TOM BARROW CO. - avaneds.com AVAN/022014-Honda Submittals/Air Distributi… · Project Engineer Architect Contractor Dwg. No. Date Location 04/12 SD-PRG ROUND PERFORATED GRILLE ROUND

TOM BARROW CO.MAIL & SHIP TO ADDRESS: Tel: (404) 351-10102800 Plant Atkinson Road Fax: (404) 350-9121Smyrna, Georgia 30080 www.tombarrow.com

To: Addison Smith Mechanical Contractor, Inc. Date: January 17, 2014110 Kingsbridge DriveCarrollton, GA 30117

Attn.: Chris Pitts

Subject: Honda ki ExpansionTallapoosa, Ga

Customer's # SMIT801 TBCo # 53902AD

Enclosed is one set of electronic submittal data on the following equipment:

Price Ind. Air Distribution Price Ind. Sound AttenuatorsAtco Flex Duct Ruskin Dampers & LouversRoyal take-off fittings

This is for:

X Submittal data for approval: order is being held subject to approval. Revised or corrected submittal data; order is being released per your instructions. Record purposes; order has been released for fabrication and shipment as soon as possible.

Record purposes; order has been released for fabrication and shipment according to your instructions.Purposes of reminding you that submittal was made sometime ago but you never released orderfor fabrication and shipment.

Furnishing you with requested operation and maintenance instructions. Email: Remarks:

Yours truly,TOM BARROW CO.

Daniel Maloy

DM:ceg

I. AIR DISTRIBUTION:

Price Industries

Mark Manufact. Frame NotesSDA Price Lay-In 1SDB Price Surface Mount 1SGA Price Surface Mount 1,2

SGB Kees Surface Mount 1,3RGA Price Surface Mount 1,2RGB Kees Surface Mount 1,3EGA Price Surface Mount 1

SDL1 Price Surface Mount 1SDL2 Price Surface Mount 1

Notes: 1. Finish to be White

2. Dampers3. Verify grille size prior to releasing

PROJECT: Honda ki ExpansionLOCATION: Tallapoosa, Ga January 17, 2014ARCHITECT: TBCo CONTACT: Daniel MaloyENGINEER: PHONE NUMBER:(404) 351-1010CONTRACTOR: Addison Smith Mechanical Contractor, Inc. JOB NUMBER: 53902AD

TOM BARROW COMPANYAtlanta*Albany*Ft. Myers*Jacksonville*Memphis*Nashville*Orlando*Pensacola*Savannah*Tampa

PRG80

AHCD1AHCD1 Spiral Duct Frame

ModelSMPD 4-way core, Style A

ARCD620DPRG80D

Project

Engineer

Architect

Contractor

Dwg. No.

Date

Location

04/12

SD-PRG

ROUND PERFORATED GRILLEROUND PANEL

To maintain KEES' policy of continuous product improvement, we reserve the right to change prices, specifications, ratings or dimensions without notice or obligation.

KEES INCORPORATED400 S. Industrial Dr.Elkhart Lake, WI 53020Phone: (920) 876-3391Fax: (920) 876-3065Website: www.kees.com

O.D.

3/8"1/2"

3/16" DiameterHoles on

1/4" StaggeredCenters

3/16" CountersunkMounting Holes

D

Qty. Model FinishDuct Size - D Panel Size O.D. Tag

PRG-04-RP

PRG-05-RP

PRG-06-RP

PRG-08-RP

PRG-10-RP

PRG-12-RP

PRG-14-RP

PRG-16-RP

6

8

8

10

12

14

16

18

O.B.D.

4

5

6

8

10

12

14

16

Available Standard Finishes: Material: Options:- White Powder Coat - Heavy Gauge Steel Construction - Aluminum Construction- Gloss Black Powder Coat Mounting: - Clear Anodized Finish - White Powder Coat- Flat Black Powder Coat - Mounting Screws Included - Gloss Black Powder Coat - Silver Metallic Powder Coat- Silver Metallic Powder Coat Optional Damper: - Flat Black Powder Coat- Primer - Round Damper (Steel or S.S.) - Stainless Steel Construction- "Anodized" Powder Coat Shipped Loose For Duct Mounting - #304 S.S. / Matte Finish - #316 S.S. / Matte Finish

Material

80 Egg Crate Grille – 1/2" x 1/2" x 1/2" CoreFastening: A

Countersunk Screw Holes

Border: F Material:1 1/4" (32) FlatFrame

Aluminum construction

Finish:B12 - White PowderCoat

Notes:1/2" x 1/2" x 1/2" aluminum grid coreFactory tolerance ± 1/32" (1)

Submittal Sheet80Egg Crate Grille

Item Tag:EGA,RGA

All metric dimensions () are soft converted. Imperial dimensions are converted to metric and rounded to the nearest millimeter.Page 1 of 1

PROJECT: 53902 - HONDA - 89KI EXPANSION SUBMITTAL NO: 259683 SUBMITTAL DATE: 1/17/2014ENGINEER: CUSTOMER: DESCRIPTION: Egg Crate Grille, 1/2" X 1/2" X 1/2"80//I/8.000,10.000,12.000,30.000/6.000,10.000,8.000,12.000/F/SW////A//B12

© Copyright Price Industries 2013Marketing Release version: 1.37.1.1, All In One version: 3.1.5

80D Egg Crate Register with Steel Damper – 1/2" x 1/2" x 1/2" CoreFastening: A

Countersunk Screw Holes

Border: F Material:1 1/4" (32) Flat Frame Aluminum construction

Damper: Coated SteelFinish:

B12 - White Powder Coat

Notes:1/2" x 1/2" x 1/2" aluminum grid coreComes with opposed blade damperFactory tolerance ± 1/32" (1)

Submittal Sheet80DEgg Crate Grille

Item Tag:RGA


PROJECT: 53902 - HONDA - 89KI EXPANSION SUBMITTAL NO: 259683 SUBMITTAL DATE: 1/17/2014ENGINEER: CUSTOMER: DESCRIPTION: Egg Crate Register with Damper, 1/2" X 1/2" X 1/2"80D//I/12.000,24.000,36.000/12.000,24.000,16.000/F/SW////A//B12


SMDP Louvered Plaque Face Ceiling Diffuser

Border 36: T-Bar Lay-In and Surface Mount Accessory SR: Square to Round Adapter

Notes: Material:2 Slot diffuser4 Way Core StyleThe core is easily removeable at the diffuser face withoutrequiring special toolsFactory tolerance ± 1/32" (1)

Steel ConstructionSR Adapter: Coated Steel Construction

Plan View: Finish:B12: White Powder Coat

Submittal SheetSMDPPlaque Face Diffuser

Item Tag:SDA


PROJECT: 53902 - HONDA - 89KI EXPANSION SUBMITTAL NO: 258582 SUBMITTAL DATE: 1/17/2014ENGINEER: CUSTOMER: DESCRIPTION: Steel Modular Diffuser With Plaque FaceSMDP//I/18/18/36/4A///SR/8,10/2/B12


ARCD Aluminum Round Cone Diffuser, 3 Position AdjustableVertical Airflow

Horizontal Airflow

Detail View: Accessory:

Notes:

Dimensions- inchesInlet Size A B C D E F

10 22 1/2 20 2 5/8 10 2 11/16 1 7/16

Horizontal to vertical pattern adjustment, three positionsTool free removal of inner coneFactory Tolerance: ± 1/32" (1)

Material:Spun Aluminum

Finish:B12: White Powder Coat

Submittal SheetARCDRound Ceiling Diffuser

Item Tag:SDB


PROJECT: 53902 - HONDA - 89KI EXPANSION SUBMITTAL NO: 260677 SUBMITTAL DATE: 1/17/2014ENGINEER: CUSTOMER: DESCRIPTION: Round Cone Diffuser-Aluminum,3 Position AdjustmentARCD//I/10/////////B12


AHCD1 High Capacity Drum Diffuser - Single Deflection

Nom. Width A B C D E F H Damper Width10 12 5 7/8 6 10 3/4 2 7/16 6 5 13/16 6 23/32

Damper: VCS3 Opposed Blade Damper

Notes: Material:Type A fastening (countersunk holes with screws)Adjustable deflector vanesDrum can be rotated to 30° on either side of the centrelineDetent for positioning allows for positive setting of the drumFactory tolerance: ± 1/32"(1)

Frame: Aluminum ConstructionDrum: Aluminum ConstructionDamper: Steel Construction


Submittal SheetAHCD1High Capacity Drum Diffuser

Item Tag:SDL


PROJECT: 53902 - HONDA - 89KI EXPANSION SUBMITTAL NO: 260738 SUBMITTAL DATE: 1/17/2014ENGINEER: CUSTOMER: DESCRIPTION: High Capacity Drum Diff-Sngle Deflec Al. ConstructAHCD1//I/18/10/////VCS3///B12


jmurphy

Rectangle

620D Louvered Aluminum Supply Register – 3/4" Blade Spacing, Double DeflectionCore Style: Fastening:Double Deflection A: Countersunk Screwholes with

Screw

Border: F Material:1 1/4" (32) Flat Frame Aluminum

Finish:B12 - White Powder Coat

Notes:Front blades parallel to Short dimensionIndividually adjustable roll formed blades on 3/4" (19) centersVCS3 opposed blade damper, coated steelFactory tolerance ± 1/32" (1)

Grilles may be constructed with mullions depending on size andoptions ordered.

Submittal Sheet620DLouvered Aluminum Register

Item Tag:SGA


PROJECT: 53902 - HONDA - 89KI EXPANSION SUBMITTAL NO: 258310 SUBMITTAL DATE: 1/17/2014ENGINEER: CUSTOMER: DESCRIPTION: Louvered Alum Dbl Deflec Regis W/Damp,3/4" Spacing620D//I/24.000/6.000/F/S////A/SW/B12



Nom. Width A B C D E F10 12 5 7/8 6 10 3/4 2 7/16 612 13 7/8 6 7/8 6 12 5/8 3 6 1/1615 17 9 13/16 6 15 13/16 3 13/16 7 9/16


Frame: Aluminum ConstructionDrum: Aluminum Construction



Item Tag:SDL1


PROJECT: 53902 - HONDA - 89KI EXPANSION SUBMITTAL NO: 260738 SUBMITTAL DATE: 1/17/2014ENGINEER: CUSTOMER: DESCRIPTION: High Capacity Drum Diff-Sngle Deflec Al. ConstructAHCD1//I/30,36,42/10,12,15////////B12



Nom. Width A B C D E F15 17 9 13/16 6 15 13/16 3 13/16 7 9/166 8 5/16 3 3/8 3 7 1/16 1 11/16 3 7/8


Frame: Aluminum ConstructionDrum: Aluminum ConstructionSpiral Duct Frame (SDFG): Galvanized Steel



Item Tag:SDL2


PROJECT: 53902 - HONDA - 89KI EXPANSION SUBMITTAL NO: 260738 SUBMITTAL DATE: 1/17/2014ENGINEER: CUSTOMER: DESCRIPTION: High Capacity Drum Diff-Sngle Deflec Al. ConstructAHCD1//I/24,48/6,15/SDFG/16,22//////B12


II. FLEX:

Atco Model 30 per attached.


TOM BARROW COMPANY Atlanta * Albany * Ft. Myers * Jacksonville * Memphis * Nashville * Orlando * Pensacola * Savannah * Tampa

UPC #030R-Value 4.2

UPC #036R-Value 6.0

UPC #031R-Value 8.0

All thermal performance (R-Values) are classified by Underwriters Laboratories in accordance with ADC Flexible Duct Performance

and Installation Standard (1991) using ASTM C-518 (1991), at installed wall thickness, on flat insulation only.

ATCO #030, 036, and 031 are UL 181, Class 1 Air Ducts and are manufactured with a tri-directional fiberglass scrim reinforced, met-

allized polyester outer jacket. The inner core of all three products is air-tight and designed for low-to-medium operating pressures in

HVAC systems. ATCO #036 and 031 have increased insulation for superior thermal performance.

Description

Flexible Duct Systems

A double lamination of tough polyester which encapsulates a steel wire helix forms the air-tight inner core of the ATCO #030, 036,

and 031. The double-layer core of each product is wrapped in multiple thicknesses of fiberglass insulation. All three products are

sheathed in a rugged and durable tri-directionally reinforced, metallized polyester jacket.

Construction

FEATURES & BENEFITS

Air-tight Inner Core - Energy efficient / No fiberglass erosion into air stream.

Encapsulated Wire Helix - No unraveling when cut to length / Quick installation

Smooth Inner Core - Low friction loss / Low operating cost.

Thick Blanket of Fiberglass Insulation - Energy efficient / Excellent thermal characteristics

Tough Reinforced Metallized Polyester Jacket - Tear and puncture resistant / Low maintenance.

Lightweight Compact Carton - Reduces warehouse and Jobsite handling cost.

APPLICATIONS & CODE COMPLIANCES*

ATCO #030, 036, and 031 are designed for indoor use as a supply and return air duct in residential and commercial low-to-medium

pressure heating and air conditioning systems. All three models can be used as a complete air duct system and/or a branch duct

connecting to mixing boxes, diffusers, light troffers, room inlets, or other terminal devices. UL 181, NFPA 90A & 90B, IMC, IRC, UMC

10-1, HUD 515-2.1 (b), Cities of Chicago, New York, San Francisco, County of Dade (Florida), California State Fire Marshal.*

*ATCO recommends that you check with the local code body having jurisdiction in your area to determine applicable codes.

25’ Insulated

UL 181

Class 1 Air Duct

bwebb

Line

PRODUCT & PERFORMANCE DATA

PERFORMANCE DATA

PRODUCT DATA

• Length: 25’, 50’ (Other lengths available as special order)

• Diameter: 3", 4”, 5”, 6”, 7”, 8”, 9”, 10”, 12”, 14”, 16”, 18”, 20”, 22"

• Vapor Barrier: Tri-directional, scrim reinforced metallized polyester

• End Treatment: 25’, 50’ -plain ends

• Packaging: 1 piece per carton

INSTALLATION

Air duct connections and joints shall be made per installation instructions

outlined by ATCO Rubber Products, Inc. and as required by the UL 181

listing procedure.

(Installation instructions are included inside each carton.)

STRAIGHT RUN* FD 72-R1 Test Code of the Air Diffusion Council. Friction loss is com-puted in inches of water gauge per 100 ft. of duct. By using CFM or FPMvalues for a given duct dimension, the friction loss can be determined.Conversion of CFM to FPM also can be made.

UPC #030R-Value 4.2

UPC #036R-Value 6.0

UPC #031R-Value 8.0

• Rated Positive Pressure: 10” w.g. per UL-181 (UL Listed pressure) rat-

ings are determined in straight lengths @ ambient termperatures.)

• Recommended Operating Pressures: (Determined in a 90° bend at el-

evated temperatures in accordance with ADC FD 72-R1 Test Code.)

Maximum Positive:

6” w.g. - 4” thru 12” Dia.

4” w.g. - 14” thru 20” Dia.

(With factory installed metal collars, 2” w.g. - all diameters)

Maximum Negative: 3/4” w.g. - all diameters

Maximum Velocity: 5,000 FPM

• Vapor Transmission: .05 perms

• Maximum Operating Temperatures:

-20°F to 140°F Continuous (@ maximum pressure)

-20°F to 180°F Continuous (@ 2” pos. w.g. max.)

-20°F to 250°F Intermittent (@ 1/2” pos. w.g. max.)

• Flame Spread: 25 max

Smoke Developed: 50 max

Warranty - ATCO warrants that all flexible ducts will be free from defects in material and workmanship for a period of five years from the date of pur-

chase only if the ducts are installed in accordance with ATCO’s installation instructions and under conditions specified in ATCO’s performance data.

The buyer’s exclusive remedies for any defect in the flexible ducts shall be replacement or refund of the purchase price, at ATCO’s option. ATCO

MAKES NO OTHER WARRANTIES, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE. IN PARTICULAR, ATCO MAKES NO WARRANTY OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. ATCO SHALL HAVE NO LIABILITY TO THE BUYER OR ANY THIRD PARTY

FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND WHATSOEVER, INCLUDING, BUT NOT LIMITED TO, PERSONAL INJURY,

PROPERTY DAMAGE, LOST PROFITS OR OTHER ECONOMIC INJURY DUE TO ANY DEFECT IN THE FLEXIBLE DUCTS. MATERIALS AND

SPECIFICATIONS FOR THE FLEXIBLE DUCTS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Manufacturing & Shipping Locations

Albuquerque, NM • Baltimore, MD • Cartersville, GA • Fort Worth, TX

Greensboro, NC • Houston, TX • Indianapolis, IN • Phoenix, AZ

Plainville, GA • Plant City, FL • Riverside, CA• Wiggins, MS

Sacramento, CA • Springdale, AR • Vineland, NJ

ATCO RUBBER PRODUCTS, INC.

CORPORATE HEADQUARTERS

7101 ATCO DRIVE

FORT WORTH, TEXAS 76118-7098

PHONE:(817) 595-2894

1-800-USS-DUCT (1-800-877-3828)

FAX: 1-800-366-3539 TELEX: 758-510

www.atcoflex.com

III. TAKE-OFF FITTINGS:

Royal Metal Products model 174 per attached.

PROJECT: Honda ki ExpansionLOCATION: Tallapoosa, Ga January 17, 2014ARCHITECT: TBCo CONTACT: Daniel MaloyENGINEER: PHONE NUMBER: (404) 351-1010CONTRACTOR: Addison Smith Mechanical Contractor, Inc. JOB NUMBER: 53902AD


SPECIFICATION DATA SHEET MODEL No. 174 AirTite w/Scoop & Damper - Pipe

100 Royal WayTemple, GA 30179

Phone (800) 520-6593Date: 10/8/2007

DIMENSIONAL DATASIZES AVAILABLE: 4" THROUGH 20" DIAMETER

FABRICATION DATAMaterial:ASTM-A653 CS Type B Galvanized Steel, G-30 Coating LFQ Chemical Treatment

Gasket:Fire Retartant Polyethylene Foam with Double Stick3M Tape UL94 HF-1

Gauges: 4"-10" 30GA12"-16" 28GA18"-20" 26GA

Die StampedDiameter Size: to fit Pipe Size Will Fit Pipe Range

4" 8" 6"-10"5" 9" 6"-10"6" 10" 8"-12"7" 10" 8"-12"8" 12" 10"-14"9" 12" 10"-14"10" 14" 12"-16"12" 16" 14"-18"14" 18" 16"-20"16" 20" 18"-22"18" 22" 20"-24"20" 24" 22"-26"

Assembly:Air Tites are assembled with 1/8" x 1/8" Zinc Coated Steel RivetsOptions:Duro Dyne #7210 ESO38R-150 3/8" Standoff Regulatorfor 1 1/2" wrapDuro Dyne #7206 ESO14R-200 1/4" Standoff Regulatorfor 2" wrap.

Superior Quality, Superior Service, Superior Value.. that's the Royal Advantage

IV. VOLUME DAMPERS:

Ruskin model MD-35 with 2" Stand-off and Hand Quadrant (Rectangular)

Ruskin model CDR-25 with 2" Stand-off and Hand Quadrant (Round)



ALL STATED SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE OR OBLIGATION.

3900 Dr. Greaves Rd. • Kansas City, MO 64030 • (816) 761-7476 • FAX (816) 765-8955

MD35MANUAL BALANCING DAMPER

FEATURES

• Non-stick non-corrosive bearings for long life and ease of opera-tion.

• Positive lock axles and shake proof linkage for low maintenanceoperation.

• Exceeds volume damper designs recommended by SMACNA.

OPTIONS

• 304 stainless steel construction.• Jackshaft to operate multi-section damper from one side.• Locking hand quadrant (one required per section unless damper

ordered with jackshaft option).• 2" (51) stand-off hand quadrant mounting bracket (ships loose

and does not include hand quadrant).• 1/2" (13) round control shaft.• Ollite bronze bearings.• Special finishes.

Spec MD35-708/Replaces MD35-207 © Ruskin 2008

®

Height

Width

APPLICATION

The MD35 is a ruggedly built damper designed espe-cially for manual balancing applications. It offers aneconomical manufactured product alternative to the"shop built" items often installed.

STANDARD CONSTRUCTION

FRAME5" x 1" x 16 gage (127 x 25 x 1.6) galvanized steelchannel with corner braces. Low profile top andbottom 31/2" x 3/8" x 16 gage (89 x 10 x 1.6) galva-nized steel channel 13" (330) high and under,actual.

BLADES8" (203) maximum width 16 gage (1.6) galvanizedsteel. Opposed blade action is standard with paral-lel blade action optional at no additional charge.

BLADE STOP20 gage (.9) galvanized steel standard for units 12”(305) high and under as required by SMACNA ductconstruction standards. Optional for units over 12”(305) high as stated by SMACNA duct constructionstandards.

FINISHMill galvanized.

LINKAGEExposed or concealed in frame as determined byRuskin.

AXLES1/2" (13) hex.

BEARINGSMolded synthetic.

CONTROL SHAFT3" (76) x 3/8" (10) square plated steel.1/2" (13) dia. jackshaft for multisection dampers.

MAXIMUM SIZESingle section – 48"w x 48"h (1219 x 1219).

MULTIPLE SECTION ASSEMBLY96"w x 96"h (2438 x 2438). Each section operatesindependently. Requires one hand quadrant persection. For larger sizes or common operation seemodel CD355.

MINIMUM SIZE6"w x 5h (152 x 127). Dampers under 10 3/8" (264)nominal are single blade.

TEMPERATURE LIMITS-40°F (-40°C) minimum and +240°F (+116°C) max-imum.

Dimensions in parenthesis ( ) indicate millimeters.

SUGGESTED SPECIFICATION

MD35 PERFORMANCE DATA

Furnish and install, at locations shown on plans or in accordancewith schedules, manual balancing dampers that meet or exceedthe following minimum construction standards: Frame shall be 16gage (1.6) galvanized steel formed into structural hat channelshape with tabbed corners for reinforcement. The blades shall besingle skin, 16 gage (1.6) galvanized steel with three longitudinal

grooves for reinforcement. Bearings shall be corrosion resistant,molded synthetic sleeve type turning in an extruded hole in thedamper frame. Axles shall be hexagonal positively locked into thedamper blade. Dampers shall in all respects be equivalent toRuskin Model MD35.

The MD35 is structurally designed for velocities to 2000 fpm andabove. Turbulence may produce objectionable noise in some con-ditions with velocities above 1500 fpm.

Dampers may tolerate higher pressures and velocities than thoselisted here. Conservative ratings are presented intentionally in aneffort to avoid misapplication. Consult Ruskin or your Ruskin repre-sentative when a damper is to be applied in conditions exceedingrecommended maximums.

INSTALLATION AND DIMENSIONAL INFORMATION

BRACING OF MULTIPLE SECTIONDAMPER ASSEMBLIES

The MD35 is intended to be self supporting only in its largest singlesection size. Multiple section damper assemblies may require brac-ing to support the weight of the assembly and to hold against sys-tem pressure. Ruskin recommends appropriate bracing to support

the damper horizontally at least once for every 8' of damper width.Vertical assemblies and higher system pressures may require morebracing.

3900 Dr. Greaves Rd.Kansas City, MO 64030(816) 761-7476FAX (816) 765-8955

www.ruskin.com

®

DamperWidth

48" (1219)

36" (991)

24" (610)

12" (305)

2.5" w.g.

3.0" w.g.

4.0" w.g.

5.0" w.g.

1500 fpm

1500 fpm

1500 fpm

1500 fpm

MaximumSystem

Pressure

MaximumSystemVelocity

Each sectionoperates

independently.Requires one

handquadrant per

section.

5"(127)MD35

OPPOSED BLADE

Damper can be providedwith optional jackshaft foroperation from one-side.

MD35Low profile top and bottom

illustrated. Typical units13" (330) high and under, actual.

MD35Blade Stop is standard for units 12”(305) high and under. Blade Stop is

optional for units over 12” (305) high.

Maximum73/16" (183)

73/16" (183)

96" Max.(2438)

96" Max.(2438)

Blade Stop

APPLICATIONCDR25 and CDO25 dampers are round and oval volume controldampers. They are designed to be installed inside duct workrather than flange mounted. They can be equipped with bladeseals if positive shut off is required.

STANDARD CONSTRUCTIONFRAME

Dampers under 6" (152) – 2" x 12 gage (50 x 2.8) steel.Dampers over 6" (152) through 12" (305) – 2" x 1/2" x 14 gage

(50 x 13 x 1.9) steel channel.Dampers above 12" through 24" (305 x 610) – 2" x 1/2" x 1/8"

(50 x 13 x 3) steel channel.Dampers above 24" (610) through 40" (1016) – 2" x 1" x 3/16"

(50 x 25 x 5) steel channel.Dampers above 40" (1016) through 48” (1219) – 21/2" x

11/2" x 1/4" (64 x 38 x 6) steel channel.BLADE

Without SealsDampers 18" (457) and under – 12 gage steel (2.8) steel.Dampers above 18" (457) – 10 gage steel (3.4) steel.

With SealsDampers 40" (1016) and under – 2 pieces of 18 gage

steel.Dampers above 40" (1016) – 10 gage with retainer ring.

AXLEAll axles to extend 6" (152) beyond damper frame.Dampers 24" (610) and under – 1/2" (13) diameter plated steel.Dampers above 24" (610) through 40" (1016) – 3/4" (19) diame-

ter plated steel.Dampers above 40" (1016) through 48" (1219) – 1" (25) plated

steel.BEARINGS

Stainless steel sleeve pressed into frame.FINISH

Aluminum paint.MAXIMUM TEMPERATURE

250°F (121°C).MINIMUM SIZE

CDR25 – 4" (102) diameter.CDO25 – 6" (152) diameter.

MAXIMUM SIZECDR25 – 48" (1219) diameter.CDO25 without center mullion – 36" (914) wide x 24" (610)

high.CDO25 with center mullion – 72" (1829) wide x 24" (610)

high.

OPTIONS• Neoprene blade seal. Maximum temperature 250°F (121°C).• Silicone blade seal. Maximum temperature 400°F (204°C).• 304 stainless steel construction.• 316 stn. stl. construction.• 3/4" (19) axle under 24" (610).

NOTES Dimensions in parenthesis ( ) indicate millimeters.Units furnished 1/8" (3) smaller than given opening dimensions.


MODELS CDR25 AND CDO25 ROUND AND OVAL CONTROL DAMPERS

ALL STATED SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE OR OBLIGATION. © Ruskin 2009Spec CDRO25-109/Replaces CDRO25-406

®

CDO25 withCenter Mullion

(Typical when A Dimensionexceeds 36" [914])

2"(51)

Diameter

Height

Width

CDO25

CDR25

PERFORMANCE DATA


Furnish and install, at locations shown on plans, or in accordancewith schedules, control dampers that meet the following minimumconstruction standards. Damper(s) shall be of the butterfly typeconsisting of a circular blade mounted to a shaft. Inside frame sur-face shall be clean and smooth with only blade pin stop projection.Frame shall support damper blade and maintain shape for installa-tion inside duct.

Leakage through damper in the closed position shall not exceed 3cfm per inch of circumference for units 40" (1016) and under at 1"(25) sp. Leakage through damper with factory mounted blade sealshall not exceed 0.15 cfm per inch of blade circumference at 1"(25) sp. Material thickness shall be equivalent to Ruskin modelCDR25 or CDO25 standard construction.


www.ruskin.com

®

48” (1219)

40” (1219)

36” (914)

24” (610)

12” (305)

6” (152)

4.0” w.g.

4.0” w.g.

4.0” w.g.

6.0” w.g.

8.0” w.g.

10.0” w.g.

2500 FPM

2500 FPM

2500 PM

4000 FPM

4000 FPM

4000 FPM

21.5

14.5

13.1

5.5

2.7

1.4

539

364

328

219

109

55

DamperWidth Inches

Maximum System

Pressure

Maximum System Velocity

% ofMax. Flow

CFM/Sq. Ft.

.40

.38

.34

.14

.07

.04

10.0

9.42

8.50

5.65

2.83

1.41

% ofMax. Flow

CFM/Sq. Ft.

Leakage w/o seals* Leakage with seals*

* Leakage information based on pressure differential of 1’ w.g. tested per AMCA Std. 500.

Dimensions in parentheses ( ) indicate millimeters.

CDR25 AND CDO25 PERFORMANCE DATA

V. LOUVERS

Ruskin model ELF375X with 5/8" 0.40 aluminum bird screen and Baked Enamel Finish to Match

Notes:1) Verify louver sizes prior to releasing.2) Color to be selected from Ruskin standard color chart.

PROJECT: Honda ki ExpansionLOCATION: Tallapoosa, Ga January 17, 2014ARCHITECT: TBCo CONTACT: Daniel MaloyENGINEER: 0 PHONE NUMBER:(404) 351-1010CONTRACTOR: Addison Smith Mechanical Contractor, Inc. JOB NUMBER: 53902AD


®

®

TYPICAL INSTALLATION DETAILS

Accessories at additional cost.

MasonryWall

WoodInstallation

Metal PanelWall

FlangeMount


®

Louver

ExtendedSill

CMU

CMU

Louver

IntegralFlangeFrame

Fastener(by others)

Louver

ExtendedSill

MetalPanel

Insulation

DripCap

Louver

Siding

Sheating


ELF6375DX and ELF6375DXH DRAINABLE STATIONARY LOUVERSEXTRUDED ALUMINUM LOUVER

ALL STATED SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE OR OBLIGATION. © Ruskin Manufacturing 1997Spec ELF6375DX/ELF6375DXH-597/Replaces ELF6375DX-296


6" (152) deep, 6063T5 extruded aluminum.ELF6375DX 1 – .081" (2.1) nominal wallthickness. ELF6375DXH – .125" (3.2) nomi-nal wall thickness. Downspouts and caulk-ing surfaces provided.

BLADES6063T5 extruded aluminum.ELF6375DX – .081" (2.1) nominal wallthickness. ELF6375DXH – .125" (3.2) nom-inal wall thickness. Drainable blades arepositioned at at 371/2° angle and spacedapproximately 529/32" (150) center to center.

SCREEN3/4" x .051" (19 x 1.3) expanded, flattenedaluminum bird screen in removable frame.Screen adds approximately 1/2" (13) to lou-ver depth.

FINISHMill.

MINIMUM SIZE12"w x 12"h (305 x 305).

APPROXIMATE SHIPPING WEIGHTELF6375DX - 4 lbs./ft.2 (19.5 kg /m2)ELF6375DXH - 6 lbs./ft.2 (29.3kg /m2)

MAXIMUM FACTORY ASSEMBLY SIZEShall be 75 sq. ft. (7m2) per section, not toexceed 120"w x 90"h (3048 x 2286) or 90"wx 120"h (2286 x 3048). Louvers larger than the maximum factoryassembly size will require field assembly ofsmaller sections.

SUPPORTSLouvers may be provided with rear mountedblade supports that increase overall louverdepth depending on louver size, assemblyconfiguration or windload.

Consult Ruskin for additional information.

FEATURESThe ELF6375DX and ELF6375DXH offers:• 57% Free Area.• Published performance ratings based on

testing in accordance with AMCA Publica-tion 511.

• High performance frame system with drain-able head collects and removes water toprovide excellent water penetration perfor-mance.

• Drain gutter in each blade minimizes watercascade between blades.

• Architecturally styled, hidden mullions allow-ing continuous line appearance up to 120"(3048).

• Aluminum construction for low maintenanceand high resistance to corrosion.

• All welded construction.

VARIATIONSVariations to the basic design of these louversare available at additional cost. They include:• Extended sill.• Hinged frame.• Front or rear security bars.• Filter racks.• A variety of bird and insect screens.• Selection of finishes: prime coat, baked

enamel (modified fluoropolymer), epoxy,Acrodize, Kynar, clear and color anodize.(Some variation in anodize color consistencyis possible.)

Consult Ruskin for other special requirements.

SIZETAG QTY. FRAME

A*-WIDE B*-HIGH

VARIATIONS

PROJECT LOCATIONARCH./ENGR. CONTRACTORREPRESENTATIVE DATE

*Units furnished 1/4" (6) smaller than given opening dimensions.Dimensions in inches, parenthesis ( ) indicate millimeters.

6"(152)

Varies

BirdScreen

FRAME CONSTRUCTION

STANDARD INTEGRAL FLANGE

A*

B*

11/2" (38)

A* x B*

1" (25)


PERFORMANCE DATA

WATER PENETRATIONTest size 48" wide x 48" high (1219 x 1219)

Beginning point of water penetration at .01 oz./sq. ft. is 1023 fpm (312 m/min).

Furnish and install louvers as hereinafter specified where shown onplans or as described in schedules. Louvers shall be stationarydrainable type with drain gutters in each blade and downspouts injambs and mullions. Louvers shall have a minimum of 57% freearea based on a 48" wide x 48" high (1219 x 1219) size. Stationarydrainable blades shall be contained within a 6" (152) frame. Louvercomponents (heads, jambs, sills, blades, & mullions) shall be fac-tory assembled by the louver manufacturer. Louver sizes too largefor shipping shall be built up by the contractor from factory assem-bled louver sections to provide overall sizes required. Louverdesign shall limit span between visible mullions to 10 feet (3) andshall incorporate structural supports required to withstand a wind-load of 20 lbs. per sq. ft. (.96kPa) (equivalent of a 90 mph wind[145 KPH] wind – specifier may substitute any loading required).

Louvers shall be Ruskin Model ELF6375DX or ELF6375DXHextruded 6063T5 aluminum construction as follows:

Frame: 6" (152) deep. ELF6375DX - .081" (2.1) nominal wallthickness. ELF6375DXH - .125" (3.2) nominal wall thickness.

Blades: ELF6375DX - .081" (2.1) nominal wall thickness.ELF6375DXH - .125" (3.2) nominal wall thickness.Drainable blades are positioned at 371/2° angle andspaced approximately 529/32" (150) center to center.

Screen: 3/4" x .051" (19 x 1.3) expanded, flattened aluminum in removable frame.

Finish: Select finish specification from Ruskin FinishesBrochure.

Published louver performance data bearing the AMCA CertifiedRatings Seal for Air Performance & Water Penetration must be sub-mitted for approval prior to fabrication and must demonstrate pres-sure drop and water penetration equal to or less than the Ruskinmodel specified.

AMCA Standard 500 provides a reasonable basis for testing andrating louvers. Testing to AMCA 500 is performed under a certainset of laboratory conditions. This does not guarantee that otherconditions will not occur in the actual environment where louversmust operate.

The louver system should be designed with a reasonable safetyfactor for louver performance. To ensure protection from watercarryover, design with a performance level somewhat below maxi-mum desired pressure drop and .01 oz./sq. ft. of water penetration.

Oz.

Wat

er/f

t2an

d (

ounc

es w

ater

/m2 )

of

Fre

e A

rea

15 m

in. t

est

per

iod

900(274)

1000(305)

1100(335)

1200(366)

1300(396)

1400(427)

0.3(3.23)

0.25(2.69)

0.2(2.15)

0.15(1.61)

0.1(1.08)

0.05(.54)

0

Free Area Velocity in feet and (meters) per minuteStandard air .075 lb/ft3

FREE AREA GUIDEFree Area Guide shows free area in ft2 and m2 for various sizes of ELF6375DX and ELF6375DXH.

Width – Inches and Meters

Ruskin Manufacturing Company certifiesthat the ELF6375DX and ELF6375DXHLouvers shown herein is licensed to bearthe AMCA Seal. The ratings shown arebased on tests and procedures per-formed in accordance with AMCAPublication 511 and comply with therequirements of the AMCA CertifiedRatings Program. The AMCA CertifiedRatings Seal applies to air performanceratings and water penetration ratingsonly.

Ratings do not include the effect ofa bird screen.

EXHAUST MODEINTAKE MODE

1.00 (25.40).90 (22.86).80 (20.32).70 (17.78).60 (15.24)

.50 (12.70)

.40 (10.16)

.30 (7.62)

.20 (5.08)

.10 (2.54)

.09 (2.29)

.08 (2.03)

.07 (1.78)

.06 (1.52)

.05 (1.27)

.04 (1.02)

.03 (.76)

.02 (.51)

.01 (.25)

100

(30)

200

(61)

300

(91)

400

(122

)

500

(152

)

600

(183

)70

0 (2

13)

800

(244

)90

0 (2

74)

1000

(3

05)

2000

(6

10)

3000

(9

14)

4000

(12

19)

5000

(152

4)

6000

(18

29)

7000

(21

34)

8000

(24

38)

9000

(27

34)

10,0

00 (

3048

)

Sta

tic

Pre

ssu

re D

rop

in In

ches

w.g

. an

d(m

m)

Air Velocity in feet and (meters) per minute through Free Area

PRESSURE DROP

Hei

gh

t –

Inch

es a

nd

Met

ers

0.310.030.580.050.860.081.140.111.410.131.690.161.970.182.240.212.520.232.800.263.080.293.350.313.630.343.910.36

0.490.050.930.091.380.131.820.172.260.212.700.253.150.293.590.334.030.374.470.424.920.465.360.505.800.546.250.58

0.670.061.280.121.890.182.500.233.110.293.720.354.330.404.940.465.550.526.160.576.760.637.370.687.980.748.590.80

0.860.081.630.152.400.223.180.303.950.374.720.445.500.516.270.587.050.667.820.738.590.809.370.87

10.140.94

10.921.01

1.040.101.980.182.920.273.870.364.800.455.750.536.690.627.630.718.570.809.510.88

10.450.97

11.401.06

12.341.15

13.281.23

1.220.112.320.223.430.324.540.425.640.526.740.637.860.738.960.83

10.060.93

11.171.04

12.271.14

13.381.24

14.481.35

15.591.45

1.410.132.680.253.960.375.240.496.520.617.790.729.080.84

10.350.96

11.621.08

12.901.20

14.181.32

15.451.44

16.731.00

18.011.67

1.590.153.030.284.470.425.920.557.350.688.790.82

10.240.95

11.671.08

13.121.22

14.561.35

16.001.49

17.4410.9118.881.75

20.321.89

1.770.163.370.314.980.466.590.618.180.769.790.91

11.401.06

13.001.21

14.601.36

16.201.51

17.811.66

19.411.80

21.021.95

22.622.10

1.960.183.730.355.500.517.280.689.040.84

10.811.00

12.591.17

14.351.33

16.131.50

17.901.66

19.671.83

21.441.99

23.212.16

24.982.32

2.140.204.080.386.020.567.970.749.890.92

11.831.10

13.781.28

15.711.46

17.651.64

19.591.82

21.532.00

23.472.18

25.412.36

27.352.54

2.320.224.420.416.530.618.640.80

10.731.00

12.831.19

14.951.39

17.041.58

19.141.78

21.241.97

23.352.17

25.452.37

27.552.56

29.652.76

2.510.234.770.447.050.669.330.87

11.581.08

13.861.29

16.141.50

18.401.71

20.671.92

22.942.13

25.212.34

27.482.55

29.752.76

32.022.98

2.690.255.130.487.570.70

10.010.93

12.441.16

14.881.38

17.331.61

19.751.84

22.192.06

24.632.29

27.072.52

29.512.74

31.942.97

34.383.19

2.880.275.480.518.090.75

10.700.99

13.291.24

15.891.48

18.511.72

21.101.96

23.712.20

26.312.44

28.912.69

31.522.93

34.123.17

36.733.41

3.060.285.820.548.600.80

11.371.06

14.131.31

16.901.57

19.681.83

22.442.09

25.212.34

27.982.60

30.742.86

33.513.11

36.283.37

39.053.63

3.250.306.180.579.120.85

12.061.12

14.981.39

17.921.67

20.871.94

23.792.21

26.732.48

29.672.76

32.603.03

35.543.30

38.483.58

41.413.85

3.430.326.520.619.630.89

12.741.18

15.821.47

18.921.76

22.042.05

25.122.33

28.222.62

31.322.91

34.423.20

37.523.49

40.623.77

43.724.06

3.610.346.870.64

10.150.94

13.421.25

16.671.55

19.941.85

23.232.16

26.482.46

29.752.76

33.013.07

36.283.37

39.553.68

42.823.98

46.094.28

120.3018

0.4624

0.6130

0.7636

0.9142

1.0748

1.2254

1.3760

1.5266

1.6872

1.8378

1.9884

2.1390

2.29

120.30

180.46

240.61

300.76

360.91

421.07

481.22

541.37

601.52

661.68

721.83

781.98

842.13

902.29

962.44

1022.59

1082.74

1142.90

1203.05


PERFORMANCE DATA

WATER PENETRATIONTest size 48" wide x 48" high (1219 x 1219)

Beginning point of water penetration at .01 oz./sq. ft. is 1023 fpm (312 m/min).

Furnish and install louvers as hereinafter specified where shown onplans or as described in schedules. Louvers shall be stationarydrainable type with drain gutters in each blade and downspouts injambs and mullions. Louvers shall have a minimum of 57% freearea based on a 48" wide x 48" high (1219 x 1219) size. Stationarydrainable blades shall be contained within a 6" (152) frame. Louvercomponents (heads, jambs, sills, blades, & mullions) shall be fac-tory assembled by the louver manufacturer. Louver sizes too largefor shipping shall be built up by the contractor from factory assem-bled louver sections to provide overall sizes required. Louverdesign shall limit span between visible mullions to 10 feet (3) andshall incorporate structural supports required to withstand a wind-load of 20 lbs. per sq. ft. (.96kPa) (equivalent of a 90 mph wind[145 KPH] wind – specifier may substitute any loading required).

Louvers shall be Ruskin Model ELF6375DX or ELF6375DXHextruded 6063T5 aluminum construction as follows:

Frame: 6" (152) deep. ELF6375DX - .081" (2.1) nominal wallthickness. ELF6375DXH - .125" (3.2) nominal wall thickness.

Blades: ELF6375DX - .081" (2.1) nominal wall thickness.ELF6375DXH - .125" (3.2) nominal wall thickness.Drainable blades are positioned at 371/2° angle andspaced approximately 529/32" (150) center to center.

Screen: 3/4" x .051" (19 x 1.3) expanded, flattened aluminum in removable frame.

Finish: Select finish specification from Ruskin FinishesBrochure.

Published louver performance data bearing the AMCA CertifiedRatings Seal for Air Performance & Water Penetration must be sub-mitted for approval prior to fabrication and must demonstrate pres-sure drop and water penetration equal to or less than the Ruskinmodel specified.

AMCA Standard 500 provides a reasonable basis for testing andrating louvers. Testing to AMCA 500 is performed under a certainset of laboratory conditions. This does not guarantee that otherconditions will not occur in the actual environment where louversmust operate.

The louver system should be designed with a reasonable safetyfactor for louver performance. To ensure protection from watercarryover, design with a performance level somewhat below maxi-mum desired pressure drop and .01 oz./sq. ft. of water penetration.

Oz.

Wat

er/f

t2an

d (

ounc

es w

ater

/m2 )

of

Fre

e A

rea

15 m

in. t

est

per

iod

900(274)

1000(305)

1100(335)

1200(366)

1300(396)

1400(427)

0.3(3.23)

0.25(2.69)

0.2(2.15)

0.15(1.61)

0.1(1.08)

0.05(.54)

0

Free Area Velocity in feet and (meters) per minuteStandard air .075 lb/ft3

FREE AREA GUIDEFree Area Guide shows free area in ft2 and m2 for various sizes of ELF6375DX and ELF6375DXH.

Width – Inches and Meters

Ruskin Manufacturing Company certifiesthat the ELF6375DX and ELF6375DXHLouvers shown herein is licensed to bearthe AMCA Seal. The ratings shown arebased on tests and procedures per-formed in accordance with AMCAPublication 511 and comply with therequirements of the AMCA CertifiedRatings Program. The AMCA CertifiedRatings Seal applies to air performanceratings and water penetration ratingsonly.

Ratings do not include the effect ofa bird screen.

EXHAUST MODEINTAKE MODE

1.00 (25.40).90 (22.86).80 (20.32).70 (17.78).60 (15.24)

.50 (12.70)

.40 (10.16)

.30 (7.62)

.20 (5.08)

.10 (2.54)

.09 (2.29)

.08 (2.03)

.07 (1.78)

.06 (1.52)

.05 (1.27)

.04 (1.02)

.03 (.76)

.02 (.51)

.01 (.25)

100

(30)

200

(61)

300

(91)

400

(122

)

500

(152

)

600

(183

)70

0 (2

13)

800

(244

)90

0 (2

74)

1000

(3

05)

2000

(6

10)

3000

(9

14)

4000

(12

19)

5000

(152

4)

6000

(18

29)

7000

(21

34)

8000

(24

38)

9000

(27

34)

10,0

00 (

3048

)

Sta

tic

Pre

ssu

re D

rop

in In

ches

w.g

. an

d(m

m)

Air Velocity in feet and (meters) per minute through Free Area

PRESSURE DROP

Hei

gh

t –

Inch

es a

nd

Met

ers

0.310.030.580.050.860.081.140.111.410.131.690.161.970.182.240.212.520.232.800.263.080.293.350.313.630.343.910.36

0.490.050.930.091.380.131.820.172.260.212.700.253.150.293.590.334.030.374.470.424.920.465.360.505.800.546.250.58

0.670.061.280.121.890.182.500.233.110.293.720.354.330.404.940.465.550.526.160.576.760.637.370.687.980.748.590.80

0.860.081.630.152.400.223.180.303.950.374.720.445.500.516.270.587.050.667.820.738.590.809.370.87

10.140.94

10.921.01

1.040.101.980.182.920.273.870.364.800.455.750.536.690.627.630.718.570.809.510.88

10.450.97

11.401.06

12.341.15

13.281.23

1.220.112.320.223.430.324.540.425.640.526.740.637.860.738.960.83

10.060.93

11.171.04

12.271.14

13.381.24

14.481.35

15.591.45

1.410.132.680.253.960.375.240.496.520.617.790.729.080.84

10.350.96

11.621.08

12.901.20

14.181.32

15.451.44

16.731.00

18.011.67

1.590.153.030.284.470.425.920.557.350.688.790.82

10.240.95

11.671.08

13.121.22

14.561.35

16.001.49

17.4410.9118.881.75

20.321.89

1.770.163.370.314.980.466.590.618.180.769.790.91

11.401.06

13.001.21

14.601.36

16.201.51

17.811.66

19.411.80

21.021.95

22.622.10

1.960.183.730.355.500.517.280.689.040.84

10.811.00

12.591.17

14.351.33

16.131.50

17.901.66

19.671.83

21.441.99

23.212.16

24.982.32

2.140.204.080.386.020.567.970.749.890.92

11.831.10

13.781.28

15.711.46

17.651.64

19.591.82

21.532.00

23.472.18

25.412.36

27.352.54

2.320.224.420.416.530.618.640.80

10.731.00

12.831.19

14.951.39

17.041.58

19.141.78

21.241.97

23.352.17

25.452.37

27.552.56

29.652.76

2.510.234.770.447.050.669.330.87

11.581.08

13.861.29

16.141.50

18.401.71

20.671.92

22.942.13

25.212.34

27.482.55

29.752.76

32.022.98

2.690.255.130.487.570.70

10.010.93

12.441.16

14.881.38

17.331.61

19.751.84

22.192.06

24.632.29

27.072.52

29.512.74

31.942.97

34.383.19

2.880.275.480.518.090.75

10.700.99

13.291.24

15.891.48

18.511.72

21.101.96

23.712.20

26.312.44

28.912.69

31.522.93

34.123.17

36.733.41

3.060.285.820.548.600.80

11.371.06

14.131.31

16.901.57

19.681.83

22.442.09

25.212.34

27.982.60

30.742.86

33.513.11

36.283.37

39.053.63

3.250.306.180.579.120.85

12.061.12

14.981.39

17.921.67

20.871.94

23.792.21

26.732.48

29.672.76

32.603.03

35.543.30

38.483.58

41.413.85

3.430.326.520.619.630.89

12.741.18

15.821.47

18.921.76

22.042.05

25.122.33

28.222.62

31.322.91

34.423.20

37.523.49

40.623.77

43.724.06

3.610.346.870.64

10.150.94

13.421.25

16.671.55

19.941.85

23.232.16

26.482.46

29.752.76

33.013.07

36.283.37

39.553.68

42.823.98

46.094.28

120.3018

0.4624

0.6130

0.7636

0.9142

1.0748

1.2254

1.3760

1.5266

1.6872

1.8378

1.9884

2.1390

2.29

120.30

180.46

240.61

300.76

360.91

421.07

481.22

541.37

601.52

661.68

721.83

781.98

842.13

902.29

962.44

1022.59

1082.74

1142.90

1203.05

®

®

TYPICAL INSTALLATION DETAILS

Accessories at additional cost.

MasonryWall

WoodInstallation

Metal PanelWall

FlangeMount


®

Louver

ExtendedSill

CMU

CMU

Louver

IntegralFlangeFrame

Fastener(by others)

Louver

ExtendedSill

MetalPanel

Insulation

DripCap

Louver

Siding

Sheating


ELF6375DX and ELF6375DXH DRAINABLE STATIONARY LOUVERSEXTRUDED ALUMINUM LOUVER

ALL STATED SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE OR OBLIGATION. © Ruskin Manufacturing 1997Spec ELF6375DX/ELF6375DXH-597/Replaces ELF6375DX-296


6" (152) deep, 6063T5 extruded aluminum.ELF6375DX 1 – .081" (2.1) nominal wallthickness. ELF6375DXH – .125" (3.2) nomi-nal wall thickness. Downspouts and caulk-ing surfaces provided.

BLADES6063T5 extruded aluminum.ELF6375DX – .081" (2.1) nominal wallthickness. ELF6375DXH – .125" (3.2) nom-inal wall thickness. Drainable blades arepositioned at at 371/2° angle and spacedapproximately 529/32" (150) center to center.

SCREEN3/4" x .051" (19 x 1.3) expanded, flattenedaluminum bird screen in removable frame.Screen adds approximately 1/2" (13) to lou-ver depth.

FINISHMill.

MINIMUM SIZE12"w x 12"h (305 x 305).

APPROXIMATE SHIPPING WEIGHTELF6375DX - 4 lbs./ft.2 (19.5 kg /m2)ELF6375DXH - 6 lbs./ft.2 (29.3kg /m2)

MAXIMUM FACTORY ASSEMBLY SIZEShall be 75 sq. ft. (7m2) per section, not toexceed 120"w x 90"h (3048 x 2286) or 90"wx 120"h (2286 x 3048). Louvers larger than the maximum factoryassembly size will require field assembly ofsmaller sections.

SUPPORTSLouvers may be provided with rear mountedblade supports that increase overall louverdepth depending on louver size, assemblyconfiguration or windload.

Consult Ruskin for additional information.

FEATURESThe ELF6375DX and ELF6375DXH offers:• 57% Free Area.• Published performance ratings based on

testing in accordance with AMCA Publica-tion 511.

• High performance frame system with drain-able head collects and removes water toprovide excellent water penetration perfor-mance.

• Drain gutter in each blade minimizes watercascade between blades.

• Architecturally styled, hidden mullions allow-ing continuous line appearance up to 120"(3048).

• Aluminum construction for low maintenanceand high resistance to corrosion.

• All welded construction.

VARIATIONSVariations to the basic design of these louversare available at additional cost. They include:• Extended sill.• Hinged frame.• Front or rear security bars.• Filter racks.• A variety of bird and insect screens.• Selection of finishes: prime coat, baked

enamel (modified fluoropolymer), epoxy,Acrodize, Kynar, clear and color anodize.(Some variation in anodize color consistencyis possible.)

Consult Ruskin for other special requirements.

SIZETAG QTY. FRAME

A*-WIDE B*-HIGH

VARIATIONS

PROJECT LOCATIONARCH./ENGR. CONTRACTORREPRESENTATIVE DATE

*Units furnished 1/4" (6) smaller than given opening dimensions.Dimensions in inches, parenthesis ( ) indicate millimeters.

6"(152)

Varies

BirdScreen

FRAME CONSTRUCTION

STANDARD INTEGRAL FLANGE

A*

B*

11/2" (38)

A* x B*

1" (25)

VI. Terminal Units

controls (controls provided by others) per attached.



Price Ind model SDV single duct terminal unit with field mounted

��

�� ! "!#$ %�&�'��'�� (�) �*�+

��'�� #,$$��-��.��/�0��1$$,$

��

��

��

�

��

��

��

��

��

��

��

��

�

��

��

��

��

� �!��"

23�4

��

��

5��6��

��

��

��7

��

� �4�

8�9�

:

��

��

� �4�

8�9�

:

��

��

8�9�

:

��

��7

�8�9�

:

��

��8��

;5:

��;

��

�� 8��

;5:

��

�&�

��

�8��

�;5:

��<��

��<�

=>��7

� �

��

��

��

� �

?� ��

8�9�

:

��

8@9:

��

8@9:

�;�

��

��A�

��'��''<��

��'�

��

��

#

��*(

*�*)1")1

B B

1$$$

"($

$$

�$$

$�#(

$�$

,�$$

#%�$$

#,��%�

�0($

($$

((�$

"B�

�+��

#$$$

��#1"$1$/�

#(1 "

��0($�) !#C�� D��!��"�#��$��#$%#�%��E��+�)��+&��E�#$$$�)*�

*�)��%��$��#��%�+&

$��&��'(

(��%�!)

�� E��)��&��F�� &'%

�E�B

��

*(*�

*)1")%

""

($$

#(

$$

�$$

$�#(

$�$B

$�$$

#�$$

#$��#�

�0($

1"(

((�$

,$�1

�+��

#$$$

��#1"$1$/�

#(1 "

��0($�) !#C�� D��!��"�#��$��#$%#�%��E��+�)��+&��E�#$$$�)*�

*�)��%��$��#��%�+&

$��&��'(

(��%�!)

�� E��)��&��F�� &'%

�E�"

��

*(*�

*)1")(

,,

,$$

#$$

$$

�$$

$�#(

$�$

$�$$

#�$$

#(��#�

�0($

B$$

((�$

",�"

�+��

#$$$

��#1"$1$/�

#(1 "

��0($�) !#C�� D��!��"�#��$��#$%#�%��E��+�)��+&��E�#$$$�)*�

*�)��%��$��#��%�+&

$��&��'(

(��%�!)

�� E��)��&��F�� &'%

�E�,

��

*(*�

*)1")B

# #

B$$

%$$

$$

�$$

$�#(

$�$

(�$$

B�$$

�0($

#$$

((�$

"B�

�+��

#$$$

��#1"$1$/�

#(1 "

��0($�) !#C�� D��!��"�#��$��#$%#�%��E��+�)��+&��E�#$$$�)*�

*�)��%��$��#��%�+&

$��&��'(

(��%�!)

�� E��)��&��F�� &'%

�E�G

��

*(*�

*)1")

B B

1$$$

"($

$$

�$$

$�#(

$�$

,�$$

#%�$$

#,��%�

�0($

($$

((�$

"B�

�+��

#$$$

��#1"$1$/�

#(1 "

��0($�) !#C�� D��!��"�#��$��#$%#�%��E��+�)��+&��E�#$$$�)*�

*�)��% ��$��#��%�+&

$��&��'(

(��%�!)

�� E��)��&��F�� &'%

�E� $

��

*(*�

*)1")#

B B

1 #(

,$$

$$

�$$

$�#(

$�$

,�$$

#%�$$

#G��%�

�0($

,$$

((�$

,B�B

�+��

#$$$

��#1"$1$/�

#(1 "

��0($�) !#C�� D��!��"�#��$��#$%#�%��E��+�)��+&��E�#$$$�)*�

*�)��%��$��#��%�+&

$��&��'(

(��%�!)

�� E��)��&��F�� &'%

�E�

��

*(*�

*)1")"

BB

1($

$$

$$

�$$

$�#(

$�

,�$$

#�$$

�0($

#B$

((�$

"G� 1

�+��

#$$$

��#1"$1$/�

#(1 "

��0($�) !#C�� D��!��"�#��$��#$%#�%��E��+�)��+&��E�#$$$�)*�

*�)��%��$��#��%�+&

$��&��'(

(��%�!)

�� E��)��&��F�� &'%

�E� #

��

*(*�

*)1"),

BB

1($

$$

$$

�$$

$�#(

$�

,�$$

#�$$

�0($

#B$

((�$

"G�1

�+��

#$$$

��#1"$1$/�

#(1 "

��0($�) !#C�� D��!��"�#��$��#$%#�%��E��+�)��+&��E�#$$$�)*�

*�)��%��$��#��%�+&

$��&��'(

(��%�!)

�� E��)��&�� F�� &'%

�E� 1

��

*(*�

*)1")G

""

($$

#(

$$

�$$

$�#(

$�$B

$�$$

#�$$

#$��#�

�0($

%($

((�$

"G�B

�+��

#$$$

��#1"$1$/�

#(1 "

��0($�) !#C�� D��!��"�#��$��#$%#�%��E��+�)��+&��E�#$$$�)*�

*�)��%��$��#��%�+&

$��&��'(

(��%�!)

�� E��)��&��F�� &'%

�E� %

��

*(��

��

""

($$

#(

$$

�$$

$�#(

$�$B

$�$$

#�$$

#$��#�

�0($

%($

((�$

"G�B

�+��

#$$$

��#1"$1$/�

#(1 "

��0($�) !#C�� D��!��"�#��$��#$%#�%��E��+�)��+&��E�#$$$�)*�

*�)��%��$��#��%�+&

$��&��'(

(��%�!)

�� E��)��&��F�� &'%

�E�

�#��

��

��$�%��

��&'

�$'�

��#��

$��(��#�

�"�%�$��)��

��

��

��#��"�

%�$��

%*�$�$��

'��

��#�

�%��$��+'$

��"��,*��

��

-.

��/��

��%�0

/��

��

� �!��".��1&��23

��)�

� ��(�

��

��

��

��

��

�

��#� ��))��$%��#��+�F#�'��

#$�#$�

#��+�F#�'��#��#��'�#��%�!#��%�&$

�(�&��%'

��&'

��$�%��$��#$%

#�%�,,()#$$,/�H��&��%'��I&��*

#��$"��'(

��%�

�(#��&'$%��F��$

�� (

(��#��&$�&I��*

�$#��#$%��

'��J

1��&'$%�(&

+��F��#��"�F�$

��$�%��!��%K��

%��#� �� ))��$

%��#��&'

$%�(&+

��

F��!��&+

�1B)#G

)#B)##

) G) "

�I&��#� �&��#F��!#$%L�F#�'��!��&+�� &'

$%�(&+

��

��F��#��&$

��%��%�!��&+��"$�I��#$��(��,,$�

(��$�*'*

�&(��#��$

"�(��'��

�*�$�*'*

��#��(��'��,'

��%��&�&(��#��

��*�$#��'$��#��*!�)�#��*

#-�*'*

�(��*#�)�I�&

+�+��

�#�+�%��&(

�$�%#*

(��

B��I�&+��"�F�$

��$��'!

��I��(��*

�$'��I*

��"�

��(

��'��%�&(

��"�F�$

��$��$� ��+#��"#'"�

��$��+�"��/�#$%

�+#��(��'��%�&(

��"�F�$

��$�I��&I�+

#��"#'"�

��I��+�"��

,��+�F#�'��#��%��F�%

�I�&*

��&'

$%�(&+

��F��&!�#�$�%��$�#��&�%#$��+��

��

��#$%#�%� 1$)#$$,�#$%��

��#$%

#�%�

,,$)#$

/�+

�� $��'%

��%'

��$%

��I��&$��&��&

$��

G�.��+�

F#�'��#��%��F�%

�I�&*��&'

$%�(&+

��F��&!

�#�$�%

��$�#��&�%#$��+

��

��

��#$%#�%� 1$)#$$

,#$%�

��

��#$%#�%�,,$

)#$$

,�� '��$��

��*#��&$�*�� &

%&�&")�I&

��+�F#�'��#$%

�%&��$&

��$��'%�

%'��$%

��I��&$�

�&��&

$��

$��*

�$#��'$��#��*

!�)��I��%��$�#��&�%#$��+��

�� GG(�#$%�+�

��##�#�#1B�

��)�

� ��(�

��

��

� ��

��!

� �� !��"� ��#��$��%�� &�� #��

��"#��&��'��(��$��)��

��#�$��%��*%*"+�"+,*%*"+�"�,*%*"+�"�,*%*"+�"�,*%*"+�"�,*%*"+�"-,.)()/�

%��$��$�� 01�� 2��34$��$�� 2�� $�� $��$��3#��

&'�(��$%�567'%(�/!47%8)74(& ��$$ ��)�%��"% ��$$ �� $�%��)*�)��'%� ��$��'%��'�&$��)%�&��'��"''�9�6� ��&'*�4��,�,�.8'�.!��3�,��3�,�3�,+3��"+�4'&:.)&.;��#&

<� �� #��4��+!��=��/��2�� >�3+�3�3�,%��4�6��2�� >+3�3�

)��! ��*�+��;�3?�� $��;�3 ��,$�� ,��=�� /�� 2��

4��4�� @.��A0�+$$1� ��=,$��3�3�B��,$��C��$�� 7.#%-�%��)8��3/"*��D�3-

%��$��)8�--�E�&%�+��

� �� ,��,��)��!

%�� $�� $�� !�� $�� 5�� /�� $�� $�� $� �� *%��*%��(�� $��

8 ��$��, �� =��"� � $�� %�� &�� !��

�� -� ��

� �� .�� ,��!

&��* ��> .)&"!��4'&:"' �4�� ='��

��+F0+:��1&�� > �

��"#��&��'��(��$��)��

��#�$��%��*%*"+�"+,*%*"+�"�,*%*"+�"�,*%*"+�"�,*%*"+�"�,*%*"+�"-,.)()/�

%��$��$�� 01�� 2��34$��$�� 2�� $�� $��$��3#��

&'�(��$%�567'%(�/!47%8)74(& ��$$ ��)�%��"% ��$$ �� $�%��)*�)��'%� ��$��'%��'�&$��)%�&��'��"''�9�6� ��&'*�4��,�,�.8'�.!��3�,��3�,�3�,+3��"+�4'&:.)&.;��#&

<� �� #��4��+!��=��/��2�� >�3+�3�3�,%��4�6��2�� >+3�3�

��

��

� ��

��!

� �� !��"� ��#��$��%�� &�� #��

��"#��&��'��(��$��)��#�$��%��*%*"+�"�,*%*"+�"�,*%*"+�"�

%��$��$�� 01�� 2��34$��$�� 2�� $�� $��$��3#��

&'�(��$%�567'%(�/!47%8)74(& ��$$ ��)�%��"% ��$$ �� $�%��)*�)��'%� ��$��'%��'�&$��)%�&��'��"''�9�6� ��&'*�4��,�,��.8'�.!��+3�,�3�,�3��"+&�/*4'&:.)&.;��#&&�/"��

<� �� #��4��+!��=��/��2�� >�3+�3�3�,%��4�6��2�� >+3�3�

)��! ��*�+��;�3?�� $��;�3 ��,$�� ,��=�� /�� 2��

4��4�� @.��A0�+$$1� ��=,$��3�3�B��,$��C��$�� 7.#%-�%��)8��3/"*��D�3-

%��$��)8�--�E�&%�+��

� �� ,��,��)��!

%�� $�� $�� !�� $�� 5�� /�� $�� $�� $� �� *%��*%��(�� $��

8 ��$��, �� =��"� � $�� %�� &�� !��

�� -� ��

� �� .�� ,��!

&��* ��> .)&"!��4'&:"' �4�� ='��

��+F0+:��1&�� > &�/*

&�/2 �� "��*'�� &�/"��0+# ��&�/,��%$��!�G��* ��!�G1

��"#��&��'��(��$��)��#�$��%��*%*"+�"�,*%*"+�"�,*%*"+�"�

%��$��$�� 01�� 2��34$��$�� 2�� $�� $��$��3#��

&'�(��$%�567'%(�/!47%8)74(& ��$$ ��)�%��"% ��$$ �� $�%��)*�)��'%� ��$��'%��'�&$��)%�&��'��"''�9�6� ��&'*�4��,�,��.8'�.!��+3�,�3�,�3��"+&�/*4'&:.)&.;��#&&�/"��

<� �� #��4��+!��=��/��2�� >�3+�3�3�,%��4�6��2�� >+3�3�

VII. SOUND ATTENUATORS:

Price sound attenuators per attached.



eeeeeeeeee

eeeeeeeeeeeeeeeeeeeeeeeeeee

lleleelleelle

44444444444444444444444

4 4 444 444 4 4 4 4 4 4 4

# yey lleee geg )eeeee)ee) )eegeee)ee) )eegeee)ee) eeleeeele )el)e)l)l) )ee)e)))l) )ee)eee)g) 33 555 550 500 5K 5K KK KK

44 4 AA 44A 4 4 44044 4 044 4044 d 4d444 4444 74 4044 44 44 44 4

4 404 44 44 4 444 444 4 44 444 4 444 4444 4 44444 4d4 44 4 4 4 4 44444 4 4 4 4 4 44444 4 4 4 4

47 4 AA 44A 4 4 44044 4 044 4044 A4 44 4 4444 74 4044 44 44 44 44 4

4 404 44 44 4 444 444 4 44 444 4 444 4444 4 44444 4d4 44 4 4 4 4 44444 4 4 4 4 4 44444 4 4 4 4

44 444444444 4 444444 4444 4 44444 44 44444 4 44 44 4 4 4 444 444444444 44 4 4 44 4 44 4 444 444444 44 444 44 4 444 44 4 44 444 .0

4x 444444 4 x 444 4 4 4 4 4 4 044 4 xx 44 4444 44

63 Hz 125 Hz 250 Hz 500 Hz 1000 Hz 2000 Hz 4000 Hz 8000 Hz

8 9 10 14 10 8 8 7


25 20 15 15 17 10 10 10

Images are generic representations of the silencer. The actual configuration may not be as shown.

Bank Information Component InformationQuantity: 1 Width (in.): 24.00 Quantity: 1Weight (lb): 102 Height (in.): 18.00 Width (in.): 24.00

Length (in.): 84.00 Height (in.): 18.00

Performance Dynamic Insertion Loss (dB)Air Volume (cfm): 1700

Air Velocity (fpm): 567Direction: ForwardPressure Drop (in. w.g.): 0.01 Generated Noise (dB)

Construction OptionsCasing: 22 GA Galvanized Acoustic Media: Glass Fiber Inlet Connection: 2" SlipPerforated Liner: 22 GA Galvanized Outlet Connection: 2" Slip

NotesPerformance data is derived from test values obtained in strict accordance with ASTM

E477-13.

All material used in the construction of Price silencers has a flame spread classification

of < 25 and a smoke development rating of < 50 when tested in accordance with ASTM

E84, UL723 and NFPA255.

Dynamic insertion losses are limited to 55 dB due to flanking.

• The installed silencer may have increased pressure drop resulting from system effect

caused by duct elements located upstream or downstream of the silencer.

• This silencer model was selected to achieve NC 40 criteria level based on octave band

sound levels of 0/0/0/0/0/0/0/0/ from 63Hz to 8000Hz.

24.00

18.00

84.00

18.00

24.00 84.00

Submittal SheetRM84/ZA

Rectangular Medium Velocity SilencerTag:DS-1

PROJECT: 53902 - HONDA - 89KI EXPANSION UNIT OF MEASURE: Imperial SUBMITTAL DATE: 1/17/2014ENGINEER: CUSTOMER: REVISION: DESCRIPTION: Rectangular Medium Velocity SilencerRM//I/84.00/Z/A/I/24.00/18.00/24.00/18.00/1/48.00/0.5/CL1/G/F//S2/S2/////P22//////



9 10 11 14 10 8 8 7


25 20 15 15 21 11 10 10

Images are generic representations of the silencer. The actual configuration may not be as shown.

Bank Information Component InformationQuantity: 1 Width (in.): 24.00 Quantity: 1Weight (lb): 102 Height (in.): 18.00 Width (in.): 24.00

Length (in.): 84.00 Height (in.): 18.00

Performance Dynamic Insertion Loss (dB)Air Volume (cfm): 1700

Air Velocity (fpm): 567Direction: ReversePressure Drop (in. w.g.): 0.01 Generated Noise (dB)

Construction OptionsCasing: 22 GA Galvanized Acoustic Media: Glass Fiber Inlet Connection: 2" SlipPerforated Liner: 22 GA Galvanized Outlet Connection: 2" Slip

NotesPerformance data is derived from test values obtained in strict accordance with ASTM

E477-13.

All material used in the construction of Price silencers has a flame spread classification

of < 25 and a smoke development rating of < 50 when tested in accordance with ASTM

E84, UL723 and NFPA255.

Dynamic insertion losses are limited to 55 dB due to flanking.

• The installed silencer may have increased pressure drop resulting from system effect

caused by duct elements located upstream or downstream of the silencer.

24.00

18.00

84.00

18.00

24.00 84.00

Submittal SheetRM84/ZA

Rectangular Medium Velocity SilencerTag:DS-2

PROJECT: 53902 - HONDA - 89KI EXPANSION UNIT OF MEASURE: Imperial SUBMITTAL DATE: 1/17/2014ENGINEER: CUSTOMER: REVISION: DESCRIPTION: Rectangular Medium Velocity SilencerRM//I/84.00/Z/A/I/24.00/18.00/24.00/18.00/1/48.00/0.5/CL1/G/F//S2/S2/////P22//////


Documents

TOM BARROW CO. - avaneds.com AVAN/022014-Honda Submittals/Air Distributi… · Project Engineer Architect Contractor Dwg. No. Date Location 04/12 SD-PRG ROUND PERFORATED GRILLE ROUND