Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
[To be published In the Gazette of India, Part-II, Section-3, Sub-section (i)]
Ministry of Environment, Forest and Climate Change
NOTIFICATION
New Delhi, the _ _, 2015
G.S.R _ _ _ _ (E). ― WHEREAS, by a notification of the Government of India in the
Ministry of Environment and Forests number S.O. 249(E), dated the 4th February, 2011,
erstwhile, the Central Government, with an objective to improve plastic waste management
system, framed the Plastic Waste (Management & Handling) Rules, 2011 for restricting the
manufacture and use of plastic carry bags and for setting up of plastic waste management
system by the municipal authorities;
AND WHEREAS an appraisal of implementation has revealed that desired results have not
been achieved by the prescribed authorities due to various reasons and a need was felt to
revisit these rules for the protection of public health and environment;
AND WHEREAS there is need to give thrust on plastic waste minimization, source
segregation, recycling, involving waste pickers, recyclers and waste processors in collection
of plastic waste fraction either from households or any other source of its generation or
intermediate material recovery facility and adopt polluter’s pay principle for the sustainability
of the waste management system;
NOW, THEREFORE, the following draft of certain rules, which the Central Government
proposes to make in exercise of the powers conferred by the sections 3, 6 and 25 of the
Environment (Protection) Act, 1986 (29 of 1986) and in supersession of the Plastic Waste
(Management & Handling) Rules, 2011 except as requisite things done or omitted to be
done before such supersession are hereby published for the information of public likely to
be affected thereby; and the notice is hereby given that the said draft rules shall be taken
into consideration on or after the expiry of a period of sixty days from the date on which
copies of this notification as published in the Gazette of India are made available to public;
The objections or suggestions to the draft rules, if any, may be addressed, within the period so specified, to the Secretary, Ministry of Environment and Forest and Climate Change, Indira Paryavaran Bhawan, Jor Bagh Road, Aliganj, New Delhi-110 003 or electronically at the e-mail address of the Ministry [email protected], [email protected];
2
;
The objections and suggestions which may be received from any person with respect to the
said draft rules before the expiry of the period so specified shall be considered by the
Central Government.
DRAFT RULES
1. Short title and commencement.-
(1) These rules shall be called the Plastic Waste Management Rules, 2015.
(2) Save as otherwise provided in these rules, they shall come into force on the date of
their final publication in the Official Gazette.
2. Application.-
(1) These rules shall apply to every waste generator, urban local body, Gram Panchayat,
manufacturer and producer.
(2) These rules shall not apply to the export oriented units or units in special economic
zones, notified by the Central Government, manufacturing their products against an
order for export: Provide that this exemption shall not apply to units engaged in
packaging of gutkha, tobacco and pan masala and also to any surplus or rejects, left
over products and the like.
3. Definitions.- In these rules, unless the context otherwise requires.-
(a) “Act” means the Environment (Protection) Act, 1986 (29 of 1986);
(b) “carry bags” mean bags made from plastic material, used for the purpose of
carrying or dispensing commodities but do not include bags that constitute or form
an integral part of the packaging in which goods are sealed prior to use;
(c) "commodity" means tangible item that may be bought or sold and includes all
marketable goods or wares;
3
(d) “compostable plastics” mean plastic that undergoes degradation by biological
processes during composting to yield CO2, water, inorganic compounds and biomass
at a rate consistent with other known compostable materials, excluding conventional
petro-based plastics, and does not leave visible, distinguishable or toxic residue;
(e) “consent" means the consent to establish and operate from the concerned State
Pollution Control Board or Pollution Control Committee granted under the Water
(Prevention and Control of Pollution) Act, 1974 (6 of 1974), and the Air (Prevention
and Control of Pollution) Act, 1981 (14 of 1981);
(f) “disintegration” means the physical breakdown of a material into very small
fragments;
(g) “extended producer’s responsibility (EPR)” means the responsibility of a
producer for the environmentally sound management of the product until the end of
its life;
(h) “food-stuffs” mean ready to eat food products, fast food, processed or cooked
food in liquid, powder, solid or semi-solid form;
(i) “facility” means the premises used for recycling, processing and disposal of plastic
waste;
(j) “institutional generator” means and includes occupier of the institutional
buildings such as building occupied by Central Government Departments, State
Government Departments, public or private sector companies, hospitals, schools,
colleges, universities or other places of education, organisation, academy, hotels and
restaurants;
(k) “manufacturer” means and include a person or unit or agency engaged in
production of plastic to be used as raw material by the producer.
(l) “multilayered packaging” means any material used or to be used for packaging
and has a combination of more than one layer of materials such as paper, paper
4
board, polymeric materials, metalised layers or aluminium foil, either in the form of a
laminate or co-extruded structure;
(m) “plastic” means material which contains as an essential ingredient a high polymer
such as polyethylene terephthalate, high density polyethylene, Vinyl (PVC), low
density polyethylene, polypropylene, polystyrene resins , multi-materials like
acrylonitrile butadiene styrene (ABS), polyphenylene oxide (PPO), polycarbonate
(PC), Polybutylene terephthalate (PBT) and which at some stage in its processing
into finished products can be shaped by flow;
(n) “plastic sheet” means and includes a broad, thin, usually rectangular mass or
piece of plastic;
(o) “plastic waste” means any product made of plastic which have been discarded
after use or after their intended life is over;
(p) “prescribed authority” means the authorities specified in rule 12;
(q) “producer” means persons engaged in manufacture of carry bags or multilayered
packaging or plastic sheets or like, and includes industries or individuals using plastic
sheets or like or covers made of plastic sheets or multilayered packaging for
packaging or wrapping the commodity;
(r) "registration” means registration with the State Pollution Control Board or
Pollution Control Committee concerned, as the case may be;
(s) “street vendor” shall have the same meaning as assigned to it in clause(l) of sub-
section (1) of Section 2 of the Street Vendors (Protection of Livelihood and
Regulation of
Street Vending) Act, 2014 (7 of 2014);
(t) “urban local body” means municipal corporation, municipality, nagar palika, nagar
nigam, nagar nanchayat, municipal council including notified area committee (NAC),
or any other local body constituted under the relevant statutes and, where the
management of plastic waste is entrusted to such agency;
5
(u) “virgin plastic” means plastic material which has not been subjected to use earlier
and has also not been blended with scrap or waste;
(v) “waste generator” means and includes every person or group of persons or
institution, residential and commercial establishments including Indian Railways and
Defense Cantonments which generate plastic waste;
(w) “waste management” means the scientific reduction, re-use, recovery, recycling,
composting or disposal of plastic waste;
(x) “waste pickers” mean individuals or groups of individuals voluntarily engaged in
the picking of recyclable plastic waste.
4. Conditions.- The manufacture, stocking, distribution, sale and use of carry bags, plastic
sheets or like, or cover made of plastic sheet and multilayered packaging, shall be
subject to the following conditions, namely:-
a) carry bags shall either be in natural shade (colourless), which is without any added
pigments or made using only those pigments and colourants which are in conformity
with Indian Standard : IS 9833:1981 titled as “List of pigments and colourants for
use in plastics in contact with foodstuffs, pharmaceuticals and drinking water”, as
amended from time to time;
b) recycled plastic or products made of recycled plastic shall not be used for storing,
carrying, dispensing or packaging food stuffs;
c) carry bag made of virgin or recycled plastic, shall not be less than 50 microns in
thickness;
d) plastic sheet or like, which is not an integral part of multilayered packaging or cover
made of plastic sheet used for packaging or wrapping the commodity shall not be
less than 50 microns in thickness;
e) the manufacturer shall not sell or provide or arrange plastic to be used as raw
6
material to a producer, not having valid registration from the concerned State
Pollution Control Boards or Pollution Control Committee;
f) sachets using plastic material shall not be used for storing, packing or selling gutkha,
tobacco and pan masala;
g) recycled carry bags shall conform to the Indian Standard: IS 14534:1998 titled as
Guidelines for Recycling of Plastics, as amended from time to time;
h) carry bags made from compostable plastics shall conform to the Indian Standard:
IS/ISO 17088:2008 titled as Specifications for Compostable Plastics, as amended
from time to time; and
i) plastic material, in any form, shall not be used in any package for packaging gutkha,
pan masala and tobacco in all forms.
5. Plastic waste management.- (1) The plastic waste management by the urban
local bodies in their respective jurisdiction shall be as under:-
a. Wet bio–degradable waste, dry recyclable and combustible wastes and
domestic hazardous wastes shall be segregated at source in accordance with
the Solid Waste Management Rules, 2015.
b. Plastic waste, which can be recycled, shall be channelized to registered plastic
waste recycler and recycling of plastic shall conform to the Indian Standard:
IS 14534:1998 titled as Guidelines for Recycling of Plastics, as amended from
time to time.
(2) Urban local bodies shall encourage the use of plastic waste by adopting suitable
technology such as in road construction, for energy recovery, etc. in compliance with the
standards and pollution control norms specified by the prescribed authority in this
regard.
(3) Processing and disposal of plastic including thermo-set plastic shall be as per the
guidelines issued by the Central Pollution Control Board from time to time.
7
(4) The inert from recycling or processing facilities of plastic waste shall be disposed of in
compliance with the Solid Waste Management Rules, 2015.
6. Responsibility of urban local body.-
(1) Every urban local body shall be responsible for development and setting up of
infrastructure for segregation, collection, storage, transportation, processing and
disposal of the plastic waste either on its own or by engaging agencies or
producers.
(2) The urban local body shall be responsible for setting up, operationalisation and
co-ordination of the waste management system and for performing the
associated functions, namely:-
(a) ensuring segregation, collection, storage, transportation, processing and
disposal of plastic waste;
(b) ensuring that no damage is caused to the environment during this process;
(c) ensuring channelization of recyclable plastic waste fraction to recyclers;
(d) ensuring processing and disposal on non-recyclable fraction of plastic waste
in accordance with the guidelines issued by the Central Pollution Control
Board;
(e) creating awareness among all stakeholders about their responsibilities;
(f) engaging civil societies or groups working with waste pickers; and
(g) ensuring that open burning of plastic waste does not take place..
(3) The urban local body for setting up of system for plastic waste shall seek
assistance of producers and such system shall be set up within one year from the
date of final publication of these rules in the Official Gazette.
7. Responsibility of Gram Panchayat.-
(1) Every gram panchayat either on its own or by engaging an agency shall set up,
operationalise and co-ordinate for waste management in the rural area under their
8
control and for performing the associated functions, namely.-
(a) ensuring segregation, collection, storage, transportation, processing and
disposal of plastic waste;
(b) ensuring that no damage is caused to the environment during this process;
(c) ensuring channelization of recyclable plastic waste fraction to recyclers
having valid registration;
(d) creating awareness among all stakeholders about their responsibilities; and
(e) ensuring that open burning of plastic waste does not take place
8. Responsibility of waste generator:- (1) The waste generator shall-
(a) take steps to minimize generation of plastic waste and segregate plastic waste at
source in accordance with the Solid Waste Management Rules, 2015;
(b) not litter the plastic waste and ensure segregated storage of waste at source and
handover segregated waste to waste pickers, registered recyclers or waste collection
agencies;
(2) All institutional generators of plastic waste, shall segregate and store the waste
generated by them in accordance with the Solid Waste Management Rules, 2015 and
handover segregated wastes to authorized waste processing or disposal facilities or
deposition centres either on its own or through the authorized waste collection
agency.
(3) All waste generators shall pay such user fee or charge as may be specified in the
bye-laws of the urban local bodies for plastic waste management such as waste
collection or operation of the facility thereof, etc.;
(4) Every person responsible for organising an event in open space, which involves
service of food stuff in plastic or multilayered packaging shall segregate and manage
the waste generated during such events in accordance with the Solid Waste
Management Rules, 2015
9. Responsibility of producers.-
(1) The producers, within a period of six months from the date of publication of these
rules, shall work out modalities for waste collection system based on Extended
Producers Responsibility and involving State Urban Development Departments, either
individually or collectively, through their own distribution channel or through the
urban local body concerned.
9
(2) The producer, within a period of three years from the date of final publication of
these rules, shall stop use of multilayered packaging and switch over to use of plastic
which is recyclable or compostable, for packaging commodity.
(3) The producer, within a period of three months from the date of final publication of
these rules in the Official Gazette shall apply to the Pollution Control Board or the
Pollution Control Committee, as the case may be, of the States or the Union
Territories concerned, for grant of registration.
(4) No producer shall on and after the expiry of a period of one year from the date of
final publication of these rules in the Official Gazette manufacture or use any plastic
or multilayered packaging for packaging of commodities without registration from the
concerned State Pollution Control Board or the Pollution Control Committees.
(5) Every producer shall maintain a record of details of the person engaged in supply of
plastic used as raw material to manufacture carry bags or plastic sheet or like or
cover made of plastic sheet or multilayered packaging.
10. Protocols for compostable plastic materials.- Determination of the degree of
degradability and degree of disintegration of plastic material shall be as per the protocols
of the Indian Standards listed in Schedule I to these rules.
11. Marking or labelling.-
(1) Each plastic carry bag and multilayered packaging shall have the following
information printed in English and in language being used in the State or the Union
Territory, namely:-
(a) name, registration number of the manufacturer and thickness in case of carry
bag; and
(b) name and registration number of the manufacturer in case of multilayered
packaging.
10
(2) Each recycled carry bag shall bear a label or a mark “recycled” as shown below and
shall conform to the Indian Standard: IS 14534: 1998 titled as “Guidelines for
Recycling of Plastics”, as amended from time to time;
NOTE: PET-Polyethylene terephthalate, HDPE-High density polyethylene, V-Vinyl
(PVC), LDPE- Low density polyethylene, PP-Polypropylene, PS-Polystyrene and Other
means all other resins and multi-materials like ABS (Acrylonitrile butadiene styrene),
PPO (Polyphenylene oxide), PC (Polycarbonate), PBT (Polybutylene terephalate) etc.
(3) Each carry bag made from compostable plastics shall bear a label “compostable” and
shall conform to the Indian Standard : IS/ISO 17088:2008 titled as Specifications for
“Compostable Plastics”.
12. Prescribed authority.-
(1) The State Pollution Control Board and Pollution Control Committee in respect of a
Union territory shall be the authority for enforcement of the provisions of these rules
relating to registration, manufacture of plastic products and multilayered packaging,
processing and disposal of plastic wastes.
(2) The concerned Secretary-in-charge of Urban Development of the State or a Union
Territory shall be the authority for enforcement of the provisions of these rules
relating to waste management by waste generator, use of plastic carry bags, plastic
sheets or like, covers made of plastic sheets and multilayered packaging.
(3) The concerned Gram Panchayat shall be the authority for enforcement of the
provisions of these rules relating to waste management by the waste generator, use
of plastic carry bags, plastic sheets or like, covers made of plastic sheets and
multilayered packaging in the rural area of the State or a Union Territory. .
11
(4) The authorities referred to in sub-rules (1) to (3) shall take the assistance of the
District Magistrate or the Deputy Commissioner within the territorial limits of the
jurisdiction of the concerned district in the enforcement of the provisions of these
rules.
13. Registration of producer, recyclers and manufacturer.-
(1) No person shall manufacture carry bags or recycle plastic bags or multilayered packaging
unless the person has obtained a registration from the State Pollution Control Board or
the Pollution Control Committee of the Union Territory concerned, as the case may be,
prior to the commencement of production;
(2) Every producer shall , for the purpose of registration or for renewal of registration, make
an application to the State Pollution Control Board or the Pollution Control Committee
of the Union territory concerned, in Form I
(3) Every person recycling or processing waste or proposing to recycle or process plastic
waste shall make an application to the the State Pollution Control Board or the Pollution
Control Committee , for grant of registration or renewal of registration for the recycling
unit, in Form II.
(4) Every manufacturer engaged in manufacturer of plastic to be used as raw material by
the producer shall make an application to the State Pollution Control Board or the
Pollution Control Committee of the Union territory concerned, for the grant of
registration or for the renewal of registration, in Form III.
(5) The State Pollution Control Board or the Pollution Control Committee shall not issue or
renew registration to plastic waste recycling or processing units unless the unit
possesses a valid consent under the Water (Prevention and Control of Pollution) Act,
1974 (6 of 1974) and the Air (Prevention and Control of Pollution) Act, 1981 (14 of
1981) alongwith a certificate of registration issued by the District Industries Centre or
any other Government agency authorised in this regard.
(6) The State Pollution Control Board or the Pollution Control Committee shall not renew
registration of producer unless the producer possesses and action plan endorsed by the
12
Secretary in charge of Urban Development of the concerned State or Union Territory for
setting of plastic waste management system.
(7) On receipt of the application complete in all respects for the registration for recycling or
processing of plastic waste under sub-rule (3), the State Pollution Control Board may,
after such inquiry as it considers necessary and on being satisfied that the applicant
possesses appropriate facilities, technical capabilities and equipment to handle plastic
waste safely, may grant registration to the applicant on fulfilment of the conditions as
may be laid down in terms of registration.
(8) Every State Pollution Control Board or Pollution Control Committee shall take a decision
on the grant of registration within ninety days of receipt of an application whcih is
complete in all respects.
(9) The registration granted under this rule shall initially be valid for a period of one year,
unless revoked, suspended or cancelled and shall subsequently be granted for three
years.
(10) State Pollution Control Board or the Pollution Control Committees shall not revoke,
suspend or cancel registration without providing the opportunity of a hearing to the
producer or person engaged in recycling or processing of plastic wastes.
(11) Every application for renewal of registration shall be made at least one hundred
twenty days before the expiry of the validity of the registration certificate.
14. Responsibility of retailers and street vendors-
(1) Retailers or street vendors shall not sell or provide commodities to consumer in carry
bags or plastic sheet or multilayered packaging, which are not manufactured and
labelled or marked, as per prescribed under these rules.
(2) Every retailers or street vendors selling or providing commodities in, plastic carry
bags or multilayered packaging or plastic sheets or like or covers made of plastic
sheets which are not manufactured or labelled or marked in accordance with these
rules shall be liable to pay such fines as specified under the bye-laws of the urban
local bodies.
13
15. Explicit pricing of carry bags.-
1) No carry bags shall be made available free of cost by retailers to consumers.
2) The concerned urban local body may by notification determine the minimum price for
carry bags depending upon their quality and size which covers their material and waste
management costs in order to encourage their re-use so as to minimize plastic waste
generation.
3) The urban local body by notification determine the manner of depositing with it the
payment made by the customers to the retailers for carry bags under sub-rule (2).
4) The urban local body shall utilize the amount paid by the customers for the carry bags
exclusively for the sustainability of the waste management system within their
jurisdictions.
16. State Level Advisory Body.-
(1) the State government or the union Territory shall, for the purpose of effective
monitoring of implementation of these rules, constitute a State Level Advisory
Committee consisting of the following persons, namely:-
(a) the Secretary, Department of Urban Development - Chairman
(b) one expert from State Department of Environment - Member
(c) one expert from State Pollution Control Board or
Pollution Control Committee - Member
(d) one expert from Urban Local Body - Member
(e) one expert from Non-Governmental Organisation - Member
(f) one expert from the field of Industry - Member and
(g) one expert from the field of academic institution - Member
(2) The State Level Advisory Body shall meet at least once in a year and may invite
experts, if it considers necessary.
14
17. Annual reports.-
(1) Every person engaged in recycling or processing of plastic waste shall prepare and
submit an annual report in Form-IV to the urban local body concerned under
intimation to the concerned State Pollution Control Board or Pollution Control
Committee by the 30th day of April of every year.
(2) Every urban local body shall prepare and submit an annual report in Form –V to the
concerned Secretary-in-charge of the Urban Development Department under
intimation to the concerned State Pollution Control Board or Pollution Control
Committee by the 30th day of July of every year.
(3) Each State Pollution Control Board or Pollution Control Committee shall prepare and
submit an annual report to the Central Pollution Control Board on the implementation
of these rules by the 30th day of September of every year.
(4) The Central Pollution Control Board shall prepare a consolidated annual report on the
use and management of plastic waste and forward it to the Central Government
along with its recommendations before the 30th day of December every year.
[F. No. 17-2/2001-HSMD]
Bishwanath Sinha
Joint Secretary
15
Schedule-I
[See rule 10]
1. IS/ISO 14851: 1999 Determination of the ultimate aerobic biodegradability of
plastic materials in an aqueous medium-Method by measuring the oxygen
demand in a closed Respirometer
2. IS/ISO 14852: 1999 Determination of the ultimate aerobic biodegradability of
plastic materials in an aqueous medium-Method by analysis of evolved carbon
dioxide
3. IS/ISO 14853: 2005 Plastics- Determination of the ultimate anaerobic
biodegradation of plastic materials in an aqueous system-Method by
measurement of biogas production
4. IS/ISO 14855-1: 2005 Determination of the ultimate aerobic biodegradability
of plastic materials under controlled composting conditions-Method by
analysis of evolved carbon dioxide (Part-1 General method)
5. IS/ISO 14855-2: 2007 Determination of the ultimate aerobic biodegradability
of plastic materials under controlled composting conditions-Method by
analysis of evolved carbon dioxide (Part-2: Gravimetric measurement of
carbon dioxide evolved in a laboratory- scale test )
6. IS/ISO 15985: 2004 Plastics- Determination of the ultimate anaerobic
biodegradation and disintegration under high-solids anaerobic digestion
conditions- Methods by analysis of released biogas
7. IS/ISO 16929: 2002 Plastics- Determination of degree of disintegration of
plastic materials under defined composting conditions in a pilot - scale test
8. IS/ISO 17556: 2003 Plastics- Determination of ultimate aerobic
biodegradability in soil by measuring the oxygen demand in a Respirometer or
the amount of carbon dioxide evolved
9. IS/ISO 20200:2004 Plastics- Determination of degree of disintegration of
plastic materials under simulated composting conditions in a laboratory - scale
test
16
FORM - I
[See rules 13 (2)]
APPLICATION FOR REGISTRATION FOR PRODUCERS
From: ..........................................
……………………………
…………………………….(Name and full address of the occupier)
To
The Member Secretary,
.............………. Pollution Control Board/Pollution Control Committee
…………………………………….
…………………………………….
Sir,
I/We hereby apply for registration under rule 9 of the Plastic Waste Management Rules,
2015
PART – A
GENERAL
1.(a) Name and location of the unit
(b) Address of the unit
(c) Registration required for manufacturing of:
(i) Carry bags:
(ii) Multilayered plastics
(d) Manufacturing capacity
(e) In case of renewal, previous registration number
and date of registration
2. Is the unit registered with the DIC/DCSSI of the
State Government/Union territory? If yes, attach
a copy.
3.(a) Total capital invested on the project
(b) Year of commencement of production
17
4. (a) List and quantum of products and by-products
(b) List and quantum of raw materials used
5. Furnish a flow diagram of manufacturing process
showing input and output in terms of products
and waste generated including for captive power
generation and water.
6. Minimum sizes and thickness of carry bags to be
manufactured
7. Status of compliance with these rules
PART – B
PERTAINING TO LIQUID EFFLUENT AND GASEOUS EMISSIONS
8. (a) Does the unit have a valid consent under the
Water (Prevention and control of Pollution)
Act, 1974 (6 of 1974)?
If yes, attach a copy
(b) Does the unit have a valid consent under the
Air (Prevention and Control of Pollution) Act,
1981 (14 of 1981)?
If yes, attach a copy
PART – C
PERTAINING TO WASTE
9.
Solid Wastes:
(a) Total quantum of waste generated
(b) Mode of storage within the plant
(c) Provision made for disposal of wastes
10. Attach/ Provide list of person supplying plastic to
be used as raw material to manufacture carry
bags or plastic sheet of like or multilayered
packaging
18
Name and Signature
Designation
Date :
Place :
19
FORM - II
[see rule 13 (3)]
APPLICATION FORM FOR REGISTRATION OF UNITS ENGAGED IN PROCESSING
OR RECYCLING OF PLASTIC WASTE
1. Name and Address of the
unit
2. Contact person with
designation, Tel./Fax
3. Date Commissioned
4. No. of workers (including
contract labour)
5. Consents Validity a. Water (Prevention & Control of Pollution) Act, 1974;
Valid up to _________________
b. Air (Prevention & Control of Pollution) Act, 1981;
Valid up to_________________
6. Authorization validity
7. Manufacturing Process Please attach a flow diagram of the manufacturing process
flow diagram for each product.
8. Products and installed
capacity of production
(MTA)
Products Installed capacity
9. Products manufactured
during the last three years
Year Product Quantity
20
(as applicable)
10. Raw material consumed
during the last three years
(as applicable)
Year Product Quantity
11. Water consumption Industrial _____________m3/day
Domestic_____________m3 / day
Date until which water cess has been paid (if applicable)
Waste water generation as per consent
_______________m3/day
Actual waste water generated (average of
last 3 months)
Industrial ____________m3 /day
Domestic ____________m3 /day
Waste water treatment (provide flow
diagram of the treatment scheme)
Industrial
Domestic
Waste water discharge Quantity _____________m3/day
Location _____________________
Analysis of treated waste water for pH, BOD,
COD, SS, O&G, any other parameter
stipulated by SPCB/PCC (attach details)
12. Air Pollution Control
a. Provide a flow diagram for emission
control system(s) installed for each
processing unit, utilities etc.
b. Details for facilities provided for
control of fugitive emissions due to
material handling, process, utilities etc.
c. Fuel consumption Fuel Qty per day/month
(i)
(ii)
d. Stack emission monitoring Stack attached
to
Emission (SPM, SO2, NOx
, etc.) mg/Nm3
21
(i)
(ii)
e. Ambient air quality Location Results
μg/m3
Parameters SPM, SO2,
NOx, etc.) μg/m3
(i)
(ii)
13. Waste Management: S
No
Type Category Qty.
a. Waste generation in processing
plastic-waste
(i)
(ii)
(iii)
b. Waste Collection and transportation
(attach details)
c. Waste Disposal details S
No
Type Category Qty
(i)
(ii)
d. Provide details of the disposal facility,
whether the facility is authorized by
SPCB/SPCC
e. Please attach analysis report of
characterization of waste generated
(including leachate test if applicable)
14. Details of plastic waste proposed to be
acquired through sale, auction, contract
or import, as the case may be, for use
as raw material
(i) Name
(ii) Quantity required /year
15. Occupational safety and health aspects Please provide details of facilities
16. Remarks:
Whether the unit has adequate
pollution control systems / equipment
to meet the standards of emission /
If Yes, please furnish details
22
effluent.
Whether unit is in compliance with
conditions laid down in the said rules.
Yes/No
Whether conditions exist or are likely to
exist of the material being handled /
processed posing adverse immediate or
delayed impacts on the environment.
Yes/No
Whether conditions exist (or are likely
to exist) of the material being handled /
processed by any means capable of
yielding another material (e.g. leachate)
which may possess eco-toxicity.
Yes/No
17. Any other relevant information
18. List of enclosures as per rule
Name and Signature
Designation
Date :
Place :
23
FORM - III
[See rules 13(4)]
APPLICATION FOR REGISTRATION FOR MANUFACTURERS
From: ..........................................
……………………………
…………………………….(Name and full address of the occupier)
To
The Member Secretary,
.............………. Pollution Control Board/Pollution Control Committee
…………………………………….
…………………………………….
Sir,
I/We hereby apply for registration under the Plastic Waste Management Rules, 2011
PART – A
GENERAL
1.(a) Name and location of the unit
(b) Address of the unit
(c) Registration required for manufacturing and
supply of raw material to be used by producers :
(d) Manufacturing capacity
(e) In case of renewal, previous registration number
and date of registration
2. Is the unit registered with the DIC/DCSSI of the
State Government/Union territory? If yes, attach
a copy.
3.(a) Total capital invested on the project
(b) Year of commencement of production
4. (a) List and quantum of products and by-products
24
(b) List of producers and quantum of raw materials
supplied to producers
7. Status of compliance with these rules
Name and Signature
Designation
Date :
Place :
25
Form - IV
[See rules 17 (1)]
Format of Annual Report by Operator of Facility to the Urban Local Body
Period of Reporting:
(1) Name of the City/Town and State:
(2) Population
(3) Area in sq. kilometers
(4) Number of wards covered
(5) Name & Address of the Urban local
body (Telephone/Fax/ E-mail)
(6) Name and Address of operator of
the facility
(7) Name of officer in-charge of the
facility
(Telephone/Fax/Mobile/ E-mail)
(8) Capacity:
(9) Technologies used for management
of plastic waste:
(10) Quantity of plastic waste received
during the year being reported upon
(11) Quantity of plastic waste processed
(in tons):
- Plastic waste recycled(in tons)
26
- Plastic waste processed (in tons)
- Used (in tons)
(12) Quantity of inert/ rejects sent for
final disposal to landfill sites:
(13) Details of land fill facility to which
inert/ rejects were sent for final
disposal:
- Address
-Telephone
(14) Attach status of compliance to
environmental conditions, if any
specified during grant of Consent or
registration
Signature of Operator
Dated :
Place:
27
Form - V
[See rules 17(2)]
FORMAT FOR ANNUAL REPORT ON PLASTIC WASTE MANAGEMENT TO BE
SUBMITTED BY THE URBAN LOCAL BODY
Period of Reporting:
(1) Name of the City/Town and State:
(2) Population
(3) Area in sq. kilometers
(4) Name & Address of Urban local body
Telephone No.
Fax No.
E-mail:
(5) Total Numbers of the wards in the area under
jurisdiction
(6) Quantity of Plastic Waste collected during the
year from area under jurisdiction (in tons)
(7) Quantity of plastic waste channelized for recycling
during the year (in tons)
(8) Quantity of plastic waste channelized for
processing during the year (in tons)
(9) Quantity of plastic waste channelized for use
during the year (in tons)
(10) Quantity of inert/rejects sent to landfill sites
during the year (in tons)
(11) Details of each of facilities used for processing
and disposal of plastic waste
Facility-I
i) Name of operator
ii) Address with Telephone Number/ Mobile
iii) Capacity
iv) Technology Used
28
v) Registration Number
vi) Validity of Registration (up to)
Facility-II
i) Name of operator
ii) Address with Telephone Number/ Mobile
iii) Capacity
iv) Technology Used
v) Registration Number
vi) Validity of Registration (up to)
(12) Total Numbers of Households in the area under
jurisdiction
(13) Number of households covered by door to door
collection
(14) Total number of commercial establishments and
Institutions in the area under jurisdiction
-Commercial establishments
- Institutions
(15) Number of commercial establishments and
Institutions covered by door to door collection
-Commercial establishments
- Institutions
(16) Summary of the mechanisms put in place for
management of plastic waste in the area under
jurisdiction along with the details of agencies
involved in door to door collection
(17) Attach details of infrastructure put in place for
management of plastic waste generated in the
area under jurisdiction
(18) Attach details of infrastructure required, if any
along with justification
(19) Number of slums identified in the area under
jurisdiction
(20) Number of slums provided with Waste
29
Management facilities:
(21) Give details of:
Urban local body’s own manpower deployed for
collection including street sweeping, secondary
storage, transportation, processing and disposal
of waste.
(22) Give details of:
Contractor/ concessionaire’s manpower deployed
for collection including street sweeping,
secondary storage, transportation, processing and
disposal of waste.
(23) Mention briefly, the difficulties being experienced
by the urban local body in complying with
provisions of these rules including the financial
constrains, if any
(24) Whether an Action Plan has been prepared for
improving solid waste management practices in
the city?
If yes (attach copy)
Date of revision:
Signature of CEO/Municipal Commissioner/
Executive Officer/Chief Officer
Date:
Place: