RENESSE

Thank you for your recent purchaseof the TOTO® product. Please read theenclosed information to ensure the safe use of your product. .

Installation and Owner’s Manual

2007.5

•

™

0GU3025

TL170SD

Important Safeguards------------1~2Specifications -------------------------3Before Installation--------------------3Set-Up Drawing -----------------------4Components ---------------------------5Installation Procedure ---------6~9How to Use ---------------------------10Maintenance --------------------11~12Troubleshooting --------------------13Replacement Parts------------------14Warranty -------------------------------15

Single Handle Lavatory Faucet

Contents

®

English Español Français

1

EN

GLIS

H

Important Safeguards (For your safety, please follow the instructions below)

Warning Do not reverse the hot and cold water inlet. You may be scalded if they are reversed.

Do Not Do not use hot water supply that is higher than185˚F (85˚C). If water is hotter than 185°F is used, do not use steam for hotwater supply. If it is broken, property damage, scalding, andother injuries may occur.

Do not disassemble

Do not disassemble or modify the item in anyway not described in this manual.

If the system is broken, property damage, scalding and otherinjuries are likely to occur.

Read the “Important Safeguards” section thoroughly before installing the product.

Warning

Caution

●The following symbols indicate safe and proper use of the product. Failure to observe them may reult in injury or property damage.

Failure to observe this symol may result in serious injury.

Failure to observe this symbol may result in injury or property damage.

Absolutely Do NOT.

Do not disassemble

Mandatory!

The following table demonstrates the use of safety symbols in this manual.

Less than185° (85˚C)

HC

Hot water Cold water

Do Not

Caution

Do notTouch You may get scalded when they are hot.

While using hot water do not touch the spoutand spout body directly.

Do not strike or kick the product If the system is broken, property damage, scalding, and otherinjuries may occur.

Do not use the product at temperature excedingwhat local codes allows. If parts are damaged, property damage, scalding and otherinjuries may occur.

HOT

Ah!

Freezing

2

EN

GLI

SH

When the valve at the hot side is opened, hot water may cause scalding.

To use hot water, you must turn the handleon the cold side first, then turn the handle on the hot side slowly and adjust the temperature.

After water is turned off, leave the handlein turned off, leave the hand in the coldside or in the middle.The next time hot water is used, the hot water remaining in the valve may cause scalding.

Before using hot water, check with yourhand that the temperature is appropriate.

When the handle on the hot side is turned, hot water may cause scalding

Warning

Mandatory

Ah!

HOT Do not

If the system has deteriorated or worn-out,property damages, scalding and other injuries may occur.

Check water leakage and looseness in the pipe (cabinet and inspection hole etc.) regular.

If the hot water pressure is higher than thatof the cold water, you will not be able to adjustthe temperature normally, and you may be scalded.

The pressure of the water supply can notbe lower than that of the hot water.The hot water pressure must be lower than thepressure of the cold water side.

Ah!

Nolooseness

Noleakage

Slowly

3

EN

GLIS

H

34 104˚F (2˚C 40˚C)

Specifications

Cold and hotwater pressure

Minimum pressure

Maximum pressure

20psi ( 0.14MPa) (flowing pressure)

Maximum use temperature

Suitable Water Quality

Suitable ambient temperture

Supply Connection

125psi (0.86MPa) (static)

Less than 185°F (85˚C)Water that meets National/Primary

drinking water regulation

3/8” NPSM

Before installation

●To prevent being scalded due to malfunction, the water supply pressure must be higher than the hot water pressure, or you can make them equal. In addition, if you inrease the pressure of the hot water, it must still be lower than that of water supply side.

● If the water supply pressure is higher than 0.86MPa, you should buy a reducing valve to reduce the pressure to the range of 0.2-0.3MPa.

To use the faucet comfortably, the recommended pressure is about 0.2-0.3MPa.

●To prevent being scalded due to malfunction, the recommended hot water supply temerature is 140°F.

Max. 2.2gpm (8.32L/min)Flow Rate

4

EN

GLI

SH

Flex Hose(Hot)

Flex Hose(Cold)

Push button(only for faucetwith pop-up drain)

Gasket

GasketFlat packing

Winged packing

Connector Assembly

Spout mounting nut

Components

Check that you have the following parts from the package.

Faucet main body parts

Some parts may be different depending on the model.

Flat washer

Lever

Outlet

Lock washer

Spout mounting flange

Spout Key

*Observe all local plumbing codes.*Make sure that water supply is shut off.*Read these instrutions carefully to ensure proper installation.*For new lavatory installation, install the faucet before installing the lavatory.

Installation andOwner’s Manual

5

EN

GLIS

H

Set-Up Drawing*Some parts may differ from the illustration depending on the model.

3/8” NPSM

5” (1

27m

m) (

CLO

SE)

6-7/

16” (

163m

m) (

OPE

N)

2-15

/16”

(75m

m)

5-5/16 “(135mm)

1-11/16” (43 mm)

5

0 ° 5 0 °

Pop-up Drain cable connector

counter hole φ 1-5/16” to 1-7/16 (φ35±2 mm)

HOT COLD

cable length = 13-13/16” (350 mm)

1-1/4” OD (32 mm OD)

8-9/16” (218 mm)

18-3/16” (462 mm)

Deck ThicknessMax. 1-3/16” (30 mm)

5-5/16 “(135mm)

3-11/16” (94 mm)

6

EN

GLI

SH

1 Clean the cold/hotwater supply pipes

1 Clean the cold/hot water supply pipes Before installation dirt and debris in the cold/ hot water supply pipes must be washed out

Important

2 Install the spout

3 Connect the cold/hot flexhoses

5 Pop-up drain with cable.

Installation Procedure

2 Install the spout.

③Insert the packing through the cold/hot water supply hoses into thegroove in the bottom of the main faucet body and into the installation hole.

②Measure the installation holes, select from the two kinds of packing to suit your needs.

④Insert the spout mounting flange, flat washer, lock washer and nut throughthe faucet mounting shaft in thatorder, face the spout to from the frontand attach the parts.

①Wipe dirt away around the instllation hole.

spout mountingflange

Faucet mounting shaft Cold Water

supply hose Hot water supply

hose

Packing

Faucet mounting shaft

Section

Flat washer Lock Washer

Nut

Spout

Close

4Pop-up Drain with Cable installation

(Only for faucet withPop-up drain).

7

EN

GLIS

H

3 Connect the cold/hot water supply hoses

*Put the gasket into the connectors and tighten the connectors in the stop valves; use the tool to fasten them.*Put the gasket into the cap nuts of the cold/hot flex hoses, screw in the connector, use the tool to fasten them.

Flex hose(Hot)

Flex hose(Cold)

Cap nut

Gasket

GasketConnector

Stop valve

8

EN

GLI

SH

The minimum bending radius of the hose is 2 3/8”(60mm), if you bend it over the limit, it will break, which may cause early damage. ●During installation, do not bend the hose from the end surface of the main faucet body too far. ●Do not pull the hose violently. This may break the hose.

If the external reinforced layer of the hose is damaged due to friction, the hose performance will deteriorate.

●Avoid unnecessary contact of similar hoses.

●You have to bend the hoses, but be careful not to break them.

Hot watersupply hose Cold water

flex hose

R= 2 3/8” (60mm)and higher

R=2 3/8”(60mm) and higher

Cautions for installing flex hoses

Good Bad Bad Bad

9

EN

GLIS

H

cabletailpiece

u-cup seal

drain body pop up

nut

drain seal

cable handleconnector

cable baseconnector

cable

lock nut

tailpiece

drain body

locknut

drain gasket

flange nut

drain body

flange

lavatory

cable

cable handleconnector

cable baseconnector

press the clip tobe able to connect

clip

clip

groove, to which connectionis to be made

4 Pop-up Drain with Cable Installation(Only for Faucet with Pop-up Drain)- Apply pipe tape to the flange threads.

- Insert flange into the drain hole.

- Assemble the gasket. flange nut and lock nut.

- Apply pipe tape to the end threads of flange threads and install the tail piece to drain body

-Make sure that cable faces toward the faucet.

- Connect the cable base connector with cable handle connector.

Push button

faucet handle

Push button

EN

GLI

SH

How to UseHow to adjust the temperature

If it is fully turned to the left side, the water temperature is at its highest.

Turn the leverFor cold water, turn it to the right side, forhot water, turn it to the left side.

To prevent scalding due to malfunction,the recommended hot water supplytemperature is 140°F (60˚C).

Right side

(Cold)

Lever

Left side(Hot)

Close

Drain

Drain

Push button

Push

Push button

Push

Open

Open and close the Pop-up valve(Only for Faucet with Pop-up drain )

Push the push button. When the pop-up is closed, water can be kept in the washbasin. Push it again, the drain is opened and water will drain out.

10

11

EN

GLIS

H

Maintenance

1. Unscrew the aerator.

3. Install the aerator.

Use attached special tool to remove it.

Use spout key provided to install it.

Brush

Aerator

Spout key

Unscrew

For best performance and sanitary environment, please maintain it everyday.

Maintain the outlet

2. Use a brush to clear the dirt and debris from the aerator.

Be careful not to lose the parts when they are removed.

Use a cloth to clean it

Use water and a damp cloth to wipe away the dirty completely.

●Slight dirty

●Seriously dirty Use a cloth with dilute detergent to wipe away the dirt, then wash and dry it.

Aerator

12

EN

GLI

SH

●Acidic cleaning agents, alkaline cleaning agents, bleaches except for the TOTO scale cleaner. ●Solvents like thinner and benzene

Notes:

Do not use the following materials, whichare harmful to the faucet surface finish.

●Cleaning agents like cleanser or grinding powder that contain coarse particles ●Nylon scrubbers and brushes

No looseness

Confirm looseness in the main body

In case of looseness, request for service to the installer, distributor or Tech Support.

If you still use it when the main body breaks loose, it will cause leakage due to the load on the pipe.

1.For maintenance press the push button at first

pop up

drain body

pop up

Unscrew the pop up counterclockwise and take it out of the drain body

Cleaning utensil such as small brush can be used to clean the pop up

pop up

small brush

Push button

Push

Open

Cleaning Drain

Looseness in the main body

Unscrew

13

Troubleshooting

Do you lower down the lever handle tostop position? (is it set to fully closed?)

Is the stop valve fully opened?

Is the aerator blocked with debris?

Is the outlet hole frozen?Check local codes with professional help and apply hotwater to the outlet.

Clean the aerator.

Use stop valve to adjust flow.

Lower the lever handle tostop position.

―

―

P.7

P.9

―

Water flowswithout stop

Flow is too small When gas water heater device is used

with the product, is the switching method set properly?

Set the gas hot water device properly with professional help.

Is the stop valve on the cold side fully opened?

―

―

―

―

―

Adjust flow with stop valve

Does the water heater give enough hot water

Check settings and functionson the hot water device

Is the aerater blocked? Page 9Clean the aerator

Too hot

Tool Cold

Temperaturecan not beadjustedeasily.

If you do not understand the position of the stop valves, ask the installer for help.

ExplanationProblem

The parts of the product need ”breaking” for a few days before they become stable. This is not a problem

The handles become harder to turn than when you started to use the product.

● You can encounter the following during use. This is not a problem

Before contacting a repairman, check the following common problems and solutions.If the problems perists, contact your dealer or tech support

Check SolutionProblem Refer to

Is the stop valve on the hot side fully opened?

Adjust flow with stop valve

Is the stop valve on the cold/ Hot sidesfully opened?

Adjust water flow with stop valve

Does the water heater give adequate water?

Check settings and functionson water heater withprofessional help

EN

GLIS

H

Replacement Parts

14

EN

GLI

SH

Set screwLeverValve cover

Spout Kit

Spout mounting kitaerator

Flex hose (Hot)Flex hose (Cold)

Drain Assembly

Cartridge

Connector assembly

1

No.123

Description

456789

1011 2

8

34

5

6

7

910

11

WARRANTY

©2007 TOTO USA, Inc. á 1155 Southern Road, Morrow GA 30260Phone (888)-295-8134 Fax (800)-699-4889 www.totousa.comTOTO USA, INC. is a wholly owned subsidiary of TOTO Ltd.

Printed in August, 20070GU3025

LIFETIME LIMITED WARRANTYWarranty applies to selected residential faucets only.1. TOTO® warrants its faucets (“Product”) to be free from defects in materials and workmanship during normal residential use for as long as the original consumer end-user purchaser owns their home. This limited lifetime warranty is extended only to the original consumer end-user purchaser and only so long as the Product remains in use by the original consumer end-user purchaser in its original place of installation in the purchaser’s residence. This warranty applies only to Product purchased and installed in North America.2. TOTO® obligations under this warranty are limited to repair or replacement, at TOTO®’s option, of Product or parts found to be defective in normal residential use, provided that such Product was properly installed and used in accordance with the owner’s manual. TOTO® reserves the right to make such inspections as may be necessary in order to determine the cause of the defect.3. This warranty does not apply to the following items:

Damage or loss sustained in a natural calamity such as fire, earthquake, flood, thunder, electrical storm, etc.Damage or loss resulting from any accident, unreasonable use, misuse, abuse, negligence, or improper care, cleaning or maintenance of the Product.Damage or loss resulting from sediments or foreign matter contained in a water system.Damage or loss resulting from improper installation or from installation of the Product in a harsh and/or hazardous environment, or improper removal, repair or modi cation of the Product.Damage or loss resulting from the use of an abrasive cleanser.

4. If the Product is used commercially, TOTO® warrants the Product to be free from defects in materials and workmanship for one (1) year from the date the Product is installed, with all other terms of this warranty applicable except the duration of the warranty.5. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE TO PROVINCE.6. To obtain warranty repair service under this warranty, you must take the Product or deliver it prepaid to a TOTO® service facility with proof of purchase (original sales receipt) together with a letter stating the problem, or contact a TOTO ® distributor or products service contractor, or write directly to TOTO® U.S.A., INC., 1155 Southern road, Morrow, Georgia 30260, (888) 295-8134. If, because of the size of the Product or nature of the defect, the Product cannot be returned to TOTO®, receipt by TOTO ® of written notice of the defect together with proof of purchase (original sales receipt) shall constitute delivery. In such case, TOTO®

may choose to repair the Product at the purchaser’s location or pay to transport the Product to a service facility. THIS WRITTEN WARRANTY IS THE ONLY WARRANTY MADE BY TOTO®. REPAIR, REPLACEMENT OR OTHER APPROPRIATE ADJUSTMENT AS PROVIDED UNDER THIS WARRANTY SHALL BE THE EXCLUSIVE REMEDY AVAILABLE TO THE ORIGINAL PURCHASER. TOTO® SHALL NOT BE RESPONSIBLE FOR LOSS OF THE PRODUCT OR FOR OTHER INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES OR EXPENSES INCURRED BY THE ORIGINAL PURCHASER, OR FOR LABOR OR OTHER COSTS DUE TO INSTALLATION OR REMOVAL, OR COSTS OF REPAIRS BY OTHERS, OR FOR ANY OTHER EXPENSE NOT SPECIFICALLY STATED. IN NO EVENT WILL TOTO®’S RESPONSIBILITY EXCEED THE PURCHASE PRICE OF THE PRODUCT. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR USE OR FOR A PARTICULAR PURPOSE, ARE EXPRESSLY LIMITED TO THE DURATION OF THIS WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION AND EXCLUSION MAY NOT APPLY TO YOU.