Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
subject to technical modifications without notice
System 3-10System C13
Tiny Tubes
Nass Controls LP Nass Magnet GmbH Precision Controls Kft.
Solenoid Valve System 3-10
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4 - 5 General Data / Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6 - 7 Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 8 - 9 Accessories / Special Remarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 10 - 11
Solenoid Valve Cartridge 13
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 12 - 13 General Data / Technical Data / Special Remarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 14 - 15
Tiny T
ubes
– 3 –
Tiny Tubes
Tiny T
ubes
Tiny Tubes
1
2
3
45
6
Solenoid Valve System 3-10
Introduction Application of System 3-10 ValvesFunction
– 4 –
subject to technical modifications without notice
Introduction
The short name “System 3-10” identifies a solenoid valve . All valves of this type have got a plunger diameter of 3 mm, which has been ascertained and fixed for the size after thorough studies . The plunger diameter is an essential influencing factor;
its optimal selection is of decisive importance . After thorough studies and testing, “System 3-10” has been proven perfect for miniature pneumatic applications .
Application of System 3-10 Valves
The solenoids are especially used in pneumatics, mainly as 3/2 way valves . The switching functions “normally closed” and “normally open” are available . With these 3/2 way control valves nominal orifices of up to 0 .7 mm can be reached at 8 bars . System 3-10 is mostly used as a pilot valve in pneumatics .
The solenoid valves were developed for the use with compressed air and other inert gases . If an application with other media is requested, Nass Magnet or its subsidiaries must be contacted in every individual case .
Function
The plunger (1) of System 3-10 is pressed downwards by the reset spring (2) . The plunger itself, however, of these valve types is not equipped with any sealing elements . The plunger moves the actuator, which picks up the sealing element (3) .In voltage-free state, the reset spring, via the plunger and the actuator, acts on thesealing element, which is pressed against the lower valve seat (4) to seal it . If the solenoid valve is put under voltage, the plunger is attracted .
The actuator is relieved and moves upward being supported by the lower pressure spring (5) . The sealing element releases the lower valve seat and seals the upper valve seat (6) . Pressure can be put on the valve in different ways, depending on a 2/2 way valve or NO valve functions, or valve seats can be left off respectively . However, for these versions different spring designs are required .
Tiny T
ubes
– 5 –
Tiny Tubes
6,8±0,103x Ø1 0
+0,2
1±0,
10
2,8±
0,10
2,8±
0,10
66 3 (R)
2 (A)
1 (P)
31
2
to connect bipolar
Solenoid Valve System 3-10
3/2 Way Solenoid ValveNormally Closed (NC)Nominal Voltage 24V DC
Pneumatic Diagram
Circuit Diagram
Pneumatic Interface ISO 15218
– 6 –
subject to technical modifications without notice
31
2
General Data
Voltage tolerance -10% . . . +10%Ambient temperature -10°C . . . +50°CRelative duty cycle 100%Activation/deactivation period 5ms / 5msInsulation class of insulating materials according to DIN VDE 0580 FDegree of protection according to EN 60529 or IEC 529 IP 00 / IP 40 (see contact type)High-voltage test according to DIN VDE 0580 500 VMedium quality according to ISO 8573-1 when using NBR sealing elements Compressed air class 3, 3, 3Average lifetime of DC valves 100 million switching operationsMounting position (preferably plunger vertical) Any Imprint (customer imprint for an addition charge) Nass Magnet
Drawing No. Part No.
Nominal Orifice
Inlet / Exhaust[mm]
Pressure[bar]
Flow Data [l/min] Output
[W]
Electrical Connection
Electrical Circuit
Manual Override
Interface Position
1 - 2 2 - 3 USC JPC PIN M Type LED Protective Circuit
Mono-stable 0° 180°
1426 50 001/7700 200 3432 0 .5/ 0 .6 8 7 9 0 .6 x x x1426 60 001/7700 200 3434 0 .5/ 0 .6 8 7 9 0 .6 x x x1426 61 007/7700 200 3460 0 .5/ 0 .6 8 7 9 0 .6 x x x1426 01 001/7700 200 3428 0 .5/ 0 .6 8 7 9 0 .65 x x x x x1426 51 001/7700 200 3370 0 .5/ 0 .6 8 7 9 0 .65 x x x x x1426 61 001/7700 200 3404 0 .5/ 0 .6 8 7 9 0 .65 x x x x x1426 01 003/7701 200 3446 0 .5/ 0 .6 10 7 9 1 .0 x x x x x1426 51 003/7701 200 3448 0 .5/ 0 .6 10 7 9 1 .0 x x x x x1426 61 005/7701 200 3501 0 .5/ 0 .6 10 7 9 1 .0 x x x x x1426 00 003/7701 200 3503 0 .7/ 0 .8 8 10 13 0 .95 x x1426 51 005/7701 200 3502 0 .7/ 0 .8 8 10 13 1 .0 x x x x x1426 51 007/7701 200 3487 0 .7/ 0 .8 8 10 13 1 .0 x x x x x1426 61 003/7701 200 3458 0 .7/ 0 .8 8 10 13 1 .0 x x x x x1426 61 009/7701 200 3465 0 .7/ 0 .8 8 10 13 1 .0 x x x x x1426 71 001/7701 200 3467 0 .7/ 0 .8 8 10 13 1 .0 x x x x x
Technical Data / Standard Versions
Tiny T
ubes
– 7 –
Tiny Tubes
1823.7
17.1
1314.2
11.5 9.8
28.5
3.1
Ø2
Manual override monostable (pushing)
Electrical connectionJPC
1314.2
1826
17.1
11.5
9.8
3.1
28.5
Ø2
Manual override monostable (pushing)
Electrical connectionUSC
Electrical Connection: USC
Electrical Connection: JPC
– 8 –
subject to technical modifications without notice
18
21.4
17.1
1314.2
11.5
9.8
28.5
3.1
Ø2
Manual override monostable (pushing)
Electrical connectionJPC
1314.2
9.7
11.5 9.8
28.5
3.1
Ø20.
64
2.54
Manual overridemonostable (pushing)
Electrical Connection: PIN
Electrical Connection: M Type
Tiny T
ubes
– 9 –
Tiny Tubes
Ø1.7
6.6
9.8 - 0.200
12
2.8±0
.102.
8±0.
10
±0.05
1±0.0
50.5 0+
0.10
6±0.
05
circular
for integrated seal
for screws
Special Remarks
All valves are designed in compliance with DIN VDE 0580 . The alignment of the valves on manifolds is possible, but can lead to a restricted function . A general lifetime of the product cannot be specified, as it is decisively influenced by ambient conditions, the single application and the combination with other components . The function can only be
guaranteed in case of exclusive use of Nass Magnet products . Should there be deviating or additional operating conditions compared to the above mentioned conditions, special testing is necessary in order to verify the usability of the Nass Magnet products . Nass Magnet or one of its subsidiaries will be glad to offer assistance .
Solenoid Valve System 3-10
Special Remarks Accessories
Pneumatic Interface
– 10 –
subject to technical modifications without notice
* Two fastening screws are required per solenoid valve
Accessories
Name / Type Drawing No. Part No. Photo Ill. with Dimensions Explanations
Connector with flying leads USC type
6-80213-0002 686 0004 Flying leads length 100 mm
Connector with flying leads USC type
6-80213-0001 686 0003 Flying leads length 300 mm
Connector with flying leads JPC type
6-80113-0002 686 0002 Flying leads length 100 mm
Connector with flying leads JPC type
6-80113-0001 686 0001 Flying leads length 300 mm
Connector with flying leads JPC type
6-80113-0003 686 0005 Flying leads length 600 mm
Fastening screw* NN 3001 004 260 7655 M 1 .6x14mm
Interface incl . sealand screws 1426 00 .0-10 260 8076 4.5
seal assembled ininterface-adapter
screw M1.7x18.5
interface - adapter
solenoid valve with ISO 15218 interface
Solenoid valve with interface-adapter
3 (R)2 (A)
1 (P)
for adaptation of the pneumatic interface (consultation with Nass Magnet necessary)
9.2
6.9
5
4.4
5.3
6.8
515.234.
98
14
M 1.
6
Ø3
Tiny T
ubes
– 11 –
Tiny Tubes
Solenoid Valve Cartridge 13
Introduction Application of Cartridge 13Function
1
2
3
45
6
– 12 –
subject to technical modifications without notice
Introduction
The short name “C13” identifies a solenoid valve with an outside diameter of 13 mm . This outside diameter characterizes a possible size of 15 mm and thereby meets the
performance characteristics to be achieved in this size order . After thorough studies and testing, “Cartridge 13” has been proven perfect for miniature pneumatic applications .
Application of Cartridge 13
C 13 is used as a 2/2 or 3/2 way valve . The switching functions „normally closed” and „normally open” are available . In case of 3/2 way valves nominal orifices of up to 0 .8 mm can be reached at 8 bars . Cartridge 13 is mainly used as a pilot valve in pneumatics .
The solenoid valves were developed for the use with compressed air and other inert gases . If an application with other media is requested, Nass Magnet or its subsidiaries must be contacted in every individual case .
Function
The plunger (1) of „Cartridge 13“ is pressed downwards by the reset spring (2) . The plunger itself is not equipped with any sealing elements . The plunger moves the actuator, which picks up the sealing element (3) . In a voltage-free state, the reset spring, via the plunger and the actuator, acts on the sealing element, which is pressed against the lower valve seat (4) to seal it . If the solenoid valve is energized, the plunger is attracted . The actuator is relieved and moves upward, supported by the lower pressure spring (5) .
The sealing element releases the lower valve seat and seals the upper valve seat (6) . Pressure can be put on the valve in different ways, depending on a 2/2 way valve or NO valve functions, or valve seats can be left off respectively . However, different spring designs are required for these versions . Please contact Nass Magnet or its subsidiaries for more information .
Tiny T
ubes
– 13 –
Tiny Tubes
12.1
5.47.62
527
.128
Ø13 Manual override
2.2
1 (P)
2 (A)
3 (R)3 (R)
12.1
5.47.62
527
.128
Ø13
2.2
1 (P)
2 (A)
3 (R)3 (R)
Solenoid Valve Cartridge 13
3/2 Way Solenoid ValveNormally Closed (NC)Nominal Voltage 24V DC
Without Manual Override
Monostable Manual Override
– 14 –
subject to technical modifications without notice
General Data
Voltage tolerance -10% . . . +10%Ambient temperature -10°C . . . +50°CRelative duty cycle 100%Activation/deactivation period 5ms / 6msInsulation class of insulating materials according to DIN VDE 0580 FDegree of protection according to EN 60529 or IEC 529 IP 00High-voltage test according to DIN VDE 0580 500 VQuality of medium according to ISO 8573-1when using NBR sealing elements Compressed air class 3, 3, 3Electrical pin distance 7 .62 mm (3/10 inch)Average lifetime of DC valves 100 million switching operationsMounting position (preferably plunger in vertical direction) Any Marking Nass Magnet’s Part Number
Drawing No. Part No. Function
Nominal Orifice
Inlet / Exhaust[mm]
Pressure[bar]
Flow Data [l/min] Voltage
[V]Output
[W]Manual Override
1 - 2 2 - 3
1429 00 000/7113 200 3435 3/2 Way NC 0 .8/0 .8 10 15 17 24 DC 0 .81429 00 500/7113 200 3437 3/2 Way NC 0 .8/0 .8 10 15 17 24 DC 0 .8 x1429 00 000/7157 200 3500 3/2 Way NC 0 .8/0 .8 10 15 17 12 DC 0 .8
Additional AC and DC version on request Additional wiring: · LED · varistor · rectifier (for AC versions) · PWM = pulse width modulation · Reduction of peformance is possible
Technical Data / Standard Versions
Special Remarks
All valves are designed in compliance with DIN VDE 0580 . A general lifetime of the products cannot be specified, as it is decisively influenced by ambient conditions, the single application and the combination with other components . The function can only be guaranteed in case of exclusive use of Nass Magnet products .
Should there be deviating or additional operating conditions compared to the above-mentioned conditions, special testing is necessary in order to verify the usability of the Nass Magnet products . Nass Magnet will be glad to advise you .
Tiny T
ubes
– 15 –
Tiny Tubes
Nass Magnet GmbHEckenerstraße 4 - 630179 HanoverGermany Tel .: +49 511 6746 - 0Fax .: +49 511 6746 - 131www .nassmagnet .dee-mail: vertrieb@nassmagnet .de
Precision Controls Kft .Henger utca 28200 VeszprémHungaryTel .: +36 88 591 - 051Fax .: +36 88 591 - 075www .precisioncontrols .hue-mail: info@precisioncontrols .hu
Nass Controls LP51509 Birch New Baltimore, Michigan 48047U .S .A .Tel .: +1 586 7 25 - 66 10Fax .: +1 586 7 25 - 58 02www .nasscontrols .come-mail: sales@nasscontrols .com
Group of Companies