TIG Workshop Report

Embed Size (px)

DESCRIPTION

tig

Citation preview

INTRODUCTION

Originally Inert Gas Tungsten Arc Welding (Tungsten Inert Gas) is a type of arc welding made the atmosphere control. Tungsten electrodes were used. Electrodes only to produce an arc only. So for the weld when the metal Additional required to weld, trunk filler rod should be fed to the weld area as methods done in oxy-gas welding process asetilina.During the welding process is a shield in the form of gas inert (argon & helium) is used to block the welded from atmospheric air. Shield works for prevent oxidation at the electrode tip, a puddle weld and the parent metal in the vicinity of the welded. There are two types of commonly used welding nozzle weld TIG operation manually. For welding use per current is low (less than ,200 amperes) when welding thin material weld nozzles are usually of the type that can cooled in air conditioning. But, for welding require more current than , 200 amperes the nozzle weld should be cooled with water so that the electrodes do not become overheated.OBJECTIVETo gain experience and knowledge of the use of TIG arc-welding and materials safe.

To discipline students using workshop should.

To provide exposure to the students about security is important.

Ensure that the students that they know how to use TIG-machine and hand tools in the right way

Improve the students during their patience do workpiece.

Able to help students in the job environment requires skill.

SAFETY DURING WORK

Some of the measures that need to $e done while in welding workshop areaWell-dressed, neat and safe.

Wear goggles when welding. Goggles protect the eyes when students operate TIG welding.

Do not look at welding with the naked eye as strong arc light can cause eye pain, glare and 1uicy.

Put the lid onto the shirt before use TIG welding.

When wearing an apron workshop always tie back not in front.

Remove watches, rings and Bracelets as they can endanger yourself while using welding conditions and cause in1ury.

Turn off welding Before cleaning.

Always ensure TIG welding and hand tools are clean.

Make sure the door is not greasy so as to avoid injuries from occurring.

Before getting into the workshop the students must clad mechanical workshop.

Students who use TIG welding or equipment without the permission of the lecturer will be disciplinary action.

In the event of any injury to the student, please report it immediately to a lecturer in action further.

ApparatusFunction

Welding machine uses an alternating current entry (AU) and produces direct current (DC).

used for drainage flow

EnhancerrodRod additive used to strengthen the connection with the molten welding rod into a cauldron of molten enhancer

Regulator and Flow Meters

-Flow meter gas measure serves as a gauge for the working pressure required.

-There are readings on the outside while the inside of the glass tube there is a ball float that will be used to show the pressure level of work required.

-Meterreadingswillbe taken at the center of the ball at the top ofthe ball

Hos

Hoseisusedto transport the gas from the cylinder to slow pipe.hos is also used to drain water conditioning to slow pipe

References

Internet

1) http://www.machinebuilding.net/ta/t0144.htm2) https://artisansasylum.com/introduction-to-tig-welding/3) http://www.wballoys.co.uk/TIG/what-is-tig-welding.htmlBook1) Basic TIG & MIG Welding

2) The Miller Tig Handbook3) How to Weld" book by BridigumCONCLUSION

From the results of this assignment I have learned many things during this protect, especially in dealing with TIG machine. This is because there are several steps that must be followed before conducting proper welding TIG is. For example: adjust the gas pressure which is suitable for welding workpiece. I also gain experience and knowledge of the use of TIG arc-welding and materials safe .At last also know how to use TIG-machine and hand tools in the right way.

Title

TIG Welding(Tungsten Inert Gas)Lecture: MOHAMAD HAZIZAN BIN ATAN