Upload
duongquynh
View
215
Download
1
Embed Size (px)
Citation preview
This page left blank intentionally.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. www.mcubetech.co.kr
Copyright ⓒ 2009-2010 Mcube Technology Co., Ltd. All rights reserved.
The Information contained in this service manual is proprietary to the Mcube Technology Co.,
Ltd. It is only used for convenience of our customers.
The information in this document is subject to change at any time without notice. No part of this
document may be reproduced or transmitted in any form or by any means, electronic or
mechanical, for any purpose, without the express written permission of Mcube Technology.
Examples or images in this document are fictitious and do not in any way represent real patient
data. For up-to-date user information, contact your local distributor or [email protected].
If it becomes necessary for the device to undergo servicing, please contact local distributor or [email protected] for more information. Any service work performed by persons who are not authorized by Mcube Technology Co., Ltd.
may void your warranty.
Manufactured by:
Distributor:
Mcube Technology Co., Ltd. Room #803 Shinnae-Technotown, 485, Sangbong-Dong, Chungnang-Gu, Seoul, 131-220, Korea
Tel. : +82-2-3421-7780 Fax. : +82-2-3421-7076 E-mail : [email protected] Web site : www.mcubetech.co.kr
Service Manual for BioCon-700
Mcube Technology Co., Ltd. www.mcubetech.co.kr
Table of Contents
1 PRODUCT CONFIGURATION ................................................................................................... 1
1.1 PRODUCT CONFIGURATION .......................................................................................................... 1 1.2 SIGNAL INTERFACE ...................................................................................................................... 2
2 STRUCTURE AND ASSEMBLING OF THE DEVICE ............................................................ 4
2.1 STRUCTURE AND ASSEMBLING OF THE BOTTOM CASE ............................................................. 4 2.2 STRUCTURE AND ASSEMBLING OF THE UPPER CASE MODULE ................................................. 6 2.3 ASSEMBLING OF THE CONTROL B/D .......................................................................................... 8 2.4 ASSEMBLING OF THE MIDDLE CASE ......................................................................................... 10 2.5 ASSEMBLING OF THE BOTTOM CASE MODULE ........................................................................ 11 2.6 ASSEMBLING OF THE BATTERY COVER .................................................................................... 12 2.7 COVER BOLT AND LED HOLE .................................................................................................... 13 2.8 ASSEMBLING OF THE PROBE BUTTON ...................................................................................... 14 2.9 ASSEMBLING OF THE MOT-PUL B/D ......................................................................................... 15 2.10 ASSEMBLING OF THE METAL PLATE ......................................................................................... 16 2.11 ASSEMBLING OF THE ASP B/D ................................................................................................. 17 2.12 ASSEMBLING OF THE UPPER CASE MODULE ............................................................................ 18 2.13 ATTACHING URETHANE SHEETS AND LABELS ........................................................................... 19
3 STRUCTURE THE SOFTWARE ......................... 오류! 책갈피가 정의되어 있지 않습니다.
3.1 STRUCTURE ............................................................ 오류! 책갈피가 정의되어 있지 않습니다. 3.2 STATE DIAGRAM ..................................................... 오류! 책갈피가 정의되어 있지 않습니다. 3.3 CIRCUIT DIAGRAM ..................................................................................................................... 20
4 DEVICE SETUP .......................................................................................................................... 24
4.1 INSTALLING OR REMOVING THE BATTERY ................................................................................. 24 4.2 CHANGING THE THERMAL PAPER ............................................................................................. 25 4.3 CHARGING THE BATTERY MODULE OF THE BIOCON-700 ........................................................ 26 4.4 CONNECTING THE PROBE TO THE SYSTEM ............................................................................... 28 4.5 ASSEMBLING THE ROLLING CART ............................................................................................ 29 4.6 CALIBRATION ............................................................................................................................. 30
5 TROUBLESHOOTING ............................................................................................................... 32
5.1 TROUBLESHOOTING ................................................................................................................... 32 5.2 MESSAGE FOR ALERT ................................................................................................................ 33
6 MAINTENANCE .......................................................................................................................... 34
6.1 BATTERY CARE .......................................................................................................................... 34 6.2 CHANGING THE BATTERY MODULES ......................................................................................... 34 6.3 CHANGING THE THERMAL PAPER ............................................................................................. 34 6.4 CLEANING & DISINFECTION ....................................................................................................... 34 6.5 WEEKLY INSPECTION ................................................................................................................. 35 6.6 DEVICE REPAIR .......................................................................................................................... 35 6.7 DISPOSAL ................................................................................................................................... 35
7 SPECIFICATIONS ...................................................................................................................... 36
7.1 SYMBOL DIRECTORY ................................................................................................................. 36 7.2 SPECIFICATION OF COMPONENTS ............................................................................................. 37
8 ENVIRONMENTAL CONDITIONS ........................................................................................... 38
8.1 BIOCON-700 .............................................................................................................................. 38 8.2 BATTERY MODULE ..................................................................................................................... 39
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 1/42 www.mcubetech.co.kr
1 Product Configuration 1.1 Product configuration
BioCon-700 is a 3-dimensional ultrasonic equipment to measure the bladder volume and
quantity of remaining urine safely and comfortably through non-invasive method. Its overall
structure is as below.
(System Diagram of the BioCon-700)
The system, in large, consists of a console, an ultrasonic probe, and a DC adapter (power).
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 2/42 www.mcubetech.co.kr
Component Function
DC Adapter Supplies a DC power required in a battery module for charging at a console.
Console Controls system operation and various signals, and handles signal transmission and reception.
Ultrasonic Probe Transmits and receives the ultrasonic signals, being used in close contact with the patient.
The Console consists of a printer module, an LCD module, a battery module, and a
control board. Its functions are as below.
Component Function
Control Board
Controls the overall system with following major functions. - Processes user’s input. - Drives the stepping motor of the thermal printer and transmits
data - Controls the charging of a battery module - Interfaces PC through USB and serial port - Displays data on LCD - Processes data received from the analog board
Battery Module Provides the power required in the system.
LCD Module Displays various information.
Printer Module Prints the information about the bladder and bladder images in the thermal printer.
The ultrasonic probe consists of a cap, a connector, and an analog board. Its
functions are as below.
Component Function
Analog Board
Transmits an ultrasonic pulse to the ultrasonic probe, which processes the signal just received and transmits the data transferred through the A/D converter to the control board in the console. It also drives the stepping motor required in imaging.
Cap Transmits ultrasonic signal
Connector Connects the ultrasonic cable to the console
1.2 Signal Interface
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 3/42 www.mcubetech.co.kr
Adapter CJ17
Control Board
ASP B/D
SD Card
USB
CJ5
CJ2
AJ2
LCD
PrinterCJ19
CJ9
MJ1
MJ3
M_P B/D
AJ1
BJ6 BJ4MechanicalPart
Probe
speakerCJ15
CJ6
CJ7
CJ8
CJ10
MJ2
BJ5
BAT CJ4
Console
(Signal Interface of the BioCon-700)
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 4/42 www.mcubetech.co.kr
2 Structure and Assembling of the Device 2.1 Structure and Assembling of the Bottom Case
2.1.1 Structure and Components of the Bottom Case The basic components forming the Bottom case of the device are printer module, speaker. The basic structure is as below.
(Structure of the Bottom Case of the Device)
The items forming the Bottom case of the device are as below.
No. Name Material Q’TY
① Bottom case PC-ABS 1EA
② Speaker 1EA
③ Printer module 1EA
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 5/42 www.mcubetech.co.kr
2.1.2 Assembling of the Bottom Case A. Interpose ② speaker into the speaker position of bottom case and fix with glue. B. Fix ③ Printer to ① bottom case. Shown as the picture below, turn the fastener to the
direction of the arrow. After it is mounted on the ① bottom case, turn and lock the fastener as it is caught to the ① bottom case.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 6/42 www.mcubetech.co.kr
2.2 Structure and Assembling of the Upper Case Module The basic components forming the upper case of the device are LCD module, and switches, and LCD holder, and control B/D, and upper case. The basic structure is as below.
(Assembling of the LCD module)
No. Name Material Q’TY
① LCD Module 1EA
② LCD Cover 1EA
③ Upper case PC-ABS 1EA
④ LCD Holder Steel 1EA
⑤ M2.5X4 mm Bolt 4EA
A. Remove ② LCD Cover from ① LCD Module. (in case of new one).
B. As shown on the Picture B, interpose ① LCD Module into the groove of ③ Upper case
C. Cover the LCD with ④ LCD Holder and fix it with ⑤ M2.5X4 mm Bolt.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 7/42 www.mcubetech.co.kr
2.2.1 Assembling of Buttons at the Upper Case
(Assembling of buttons at the upper case)
No. Name Material Q’TY
① Upper case PC-ABS 1EA
② Main Button PC-ABS 1EA
③ Scan Button PC-ABS 1EA
④ M2X4mm Bolt 4EA
A. Put ② main button into the ① Upper case and fix it with ④ M2X4mm Bolt.
B. Put ③ Scan button into the ① Upper case and fix it with ④ M2X4mm Bolt.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 8/42 www.mcubetech.co.kr
2.3 Assembling of the Control B/D
(Connection of the connecter)
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 9/42 www.mcubetech.co.kr
No. Name Material Q’TY
① Upper case PC-ABS 1EA
② Control B/D PC-ABS 1EA
③ M2X4mm Bolt 8EA
A. Assemble the Connecters, A, B and C as shown on the picture. Mount ② Control B/D
to ①Upper case and then fix it with ③M2X4mm Bolt.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 10/42 www.mcubetech.co.kr
2.4 Assembling of the Middle Case
(Assembling of the middle case)
No. Name Material Q’TY
① Upper case PC-ABS 1EA
② Middle case PC-ABS 1EA
③ M2.4X10mm Bolt 6EA
④ M2X4mm Flat Head Bolt 2EA
A. Put the part A first as shown on the Picture A when assemble ② Middle case to ① Upper case.
B. Fix ② Middle case with ③ M2.4X10mm Bolt.
C. Fix ② Middle case with ④ M2X10mm Flat Head Bolt.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 11/42 www.mcubetech.co.kr
2.5 Assembling of the Bottom Case Module
No. Name Material Q’TY
① Upper case PC-ABS 1EA
② Bottom case PC-ABS 1EA
③ M2.5X5mm Bolt 4EA
A. Link the Connection A, B and C to each corresponding socket.
B. Mount ② Bottom case first, and then fix the unit with ③ M2.5X5mm Bolt
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 12/42 www.mcubetech.co.kr
2.6 Assembling of the Battery Cover
No. Name Material Q’TY
① Console PC-ABS 1EA
② Battery 1EA
③ Battery Cover PC-ABS 1EA
④ M2X 4mm Bolt 2EA
A. Put ② Battery into ① Console and then slide up ③ Battery Cover horizontally as shown on the
Picture A. B. Fix ③ Battery Cover with ④ M2X 4mm Bolt.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 13/42 www.mcubetech.co.kr
2.7 Cover bolt and LED hole
No. Name Material Q’TY
① Console PC-ABS 1EA
② Urethane sheet for LED Urethane 1EA
③ Urethane sheet for Bolt hole Urethane 1EA
A. Cover the LED hole with ② Urethane sticker and cover Bolt holes with ③ Urethane stickers.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 14/42 www.mcubetech.co.kr
2.8 Assembling of the Probe Button
No. Name Material Q’TY
① Probe Upper Cover PC-ABS 1EA
② Probe Button Silicone 1EA
③ Button Bracket Steel 1EA
④ M2X 4mm Bolt 4EA
A. Insert ② Probe Button into the hole of ① Probe Upper Cover in right direction.
B. Fix ② Probe Button with ③ Button Bracket firmly.
C. Fix with ④ M2X 4mm Bolt.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 15/42 www.mcubetech.co.kr
2.9 Assembling of the Mot-Pul B/D
No. Name Material Q’TY
① Probe mechanical module 1EA
② Probe Bottom Cover PC-ABS 1EA
③ Mot-Pul B/D 1EA
④ Cable 1EA
⑤ M2.5 X 6mm Support 4EA
A. Connect 12pin connector of ④ Cable to ③ Mot-Pul B/D.
B. Assemble ④ Cable to ② Probe Bottom Cover.
C. Connect ③ Mot-Pul B/D to ① Probe mechanical module
D. As shown on the Picture B, assemble ① Probe mechanical module and ② Probe Bottom Cover.
E. Fix ③ Mot-Pul B/D to ② Probe Bottom Cover with ⑤ M2.5 X 6mm Support.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 16/42 www.mcubetech.co.kr
2.10 Assembling of the Metal Plate
No. Name Material Q’TY
① Probe CKDⅠ 1EA
② Probe Metal Plate Steel 1EA
③ M2.5 X 6mm Support 4EA
④ M2.5 X 4mm Flat Head Bolt 2EA
A. Place ② Probe Metal Plate onto ① Probe CKD(complete knockdown)
B. Fix ② Probe Metal Plate with ④ M2.5 X 4mm Flat Head Bolt.
C. Fix ③ M2.5 X 6mm Support as shown on the Picture A.
D. Fix the shield of Cable to ② Probe Metal Plate
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 17/42 www.mcubetech.co.kr
2.11 Assembling of the ASP B/D
No. Name Material Q’TY
① Probe CKD Ⅱ 1EA
② ASP B/D 1EA
③ M2.5 X 4mm Bolt 4EA
A. Fix ② ASP B/D to ① Probe CKD with Ⅱ ③ M2.5 X 4mm Bolt.
B. Connect B2B B/D and ASP B/D with Coaxial cable.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 18/42 www.mcubetech.co.kr
2.12 Assembling of the Upper case module
No. Name Material Q’TY
① Probe CKD Ⅲ 1EA
② Upper case module Steel 1EA
③ M2 X 4mm Bolt 2EA
④ M2 X 4mm Flat Head Bolt 8EA
A. Assemble ① Probe CKD Ⅲ and ② Upper case module. B. Fix ① Probe CKD and Ⅲ ② Upper case module with ③M2 X 4mm Bolt and ④ M2 X 4mm Flat
Head Bolt.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 19/42 www.mcubetech.co.kr
2.13 Attaching urethane sheets and labels
A. Attach the ② Urethane labels to ① finished Probe as shown on the Picture A.
A. Shown as above Picture A, attach the label on the finished Probe and Console.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 20/42 www.mcubetech.co.kr
3 Circuit Diagram
R27 100/1005
R25 100/1005R26 100/1005
R241 100/1005R240 100/1005
nRESETJ12
nRSTOUT/GPA21J16
VSSA_ADC T14
VSSiF6
VSSi F9
VSSiB17
VSSiF11
VSSiH15
VSSi_MPLLM13
VSSi_UPLLN15
VDDaliv e (1.8V)G6
VDDaliv e (1.8V)J14
nBATT_FLTJ17PWREN J15
RTCVDD (1.8V)M12
VDDA_ADC (3.3V)P15
VDDi (1.8V)D11
VDDi (1.8V)C4
VDDi (1.8V)C17
VDDi (1.8V)C8
VDDi (1.8V)J13
VDDi_MPLL (1.8V)P14
VDDi_UPLL (1.8V)L11
VDDiarm (1.8V)G7
VDDiarm (1.8V)K3
VDDiarm (1.8V)L5
VDDiarm (1.8V)M7
VDDiarm (1.8V)N10
VDDiarm (1.8V)R1
VDDiarm (1.8V)N5
VDDMOP (SCLK ,100MHz:3.3V)D8
VDDMOP (SCLK ,100MHz:3.3V)E11
VDDMOP (SCLK ,100MHz:3.3V)A15
VDDMOP (SCLK ,100MHz:3.3V)A6
VDDMOP (SCLK ,100MHz:3.3V)E5
VDDMOP (SCLK ,100MHz:3.3V)B4
VDDMOP (SCLK ,100MHz:3.3V)H14
VDDOP (3.3V)K1
VDDOP (3.3V)M6
VDDOP (3.3V)N16
VDDOP (3.3V)N9
VSSiarmH1
VSSiarmJ7
VSSiarmM1
VSSiarm N8
VSSiarmM5
VSSiarmM9
VSSiarmU4
VSSMOPF12
VSSMOPE6
VSSMOPA12
VSSMOP D3
VSSMOPG9
VSSMOPF8
VSSMOPF3
VSSMOPC10
VSSMOPD15
VSSOPF5
VSSOPH13
VSSOPK5
VSSOPT9
VSSOP P12
VSSOPR5
U1CS3C2410A-266MHZ
R235 100/1005R234 100/1005
BATSMBR71 22/1005
R59 100/1005USB_EOT
SX_INT
USB_INT
R66 100/1005PWR_OUT
R10 100/1005
R28 100/1005R29 100/1005
R222 100/1005R221 100/1005R220 100/1005
R223 100/1005
nCD_SDWP_SD
CM
810
4/10
05
TP3
VDDMPLL
VDD33V
TOUT3
VDDiarm
VDDi
VDDMOP
VDDADC
VDDUPLL
VDDIO
CM
22op
en/1
005
CM
21op
en/1
005
TOUT4
R57
10K/1005
LnTRST
R73 100/1005
YMON_nXPON_
nYPON_
XMON_
CM
910
4/10
05
LTCK
LADDR25LADDR24
LADDR[25:24]
CM
1010
4/10
05
LTDI
SCLK1SCLK0SCLE
LTMS
VDD33V
LED_STATUS
DEBUG LED
CM5
220/1005
R75 100/1005
RTC Clock
D1
LED/2012/GREEN
R82 470/1005
R237 100/1005R236 100/1005
X232.768kHz
CM4
220/1005
CM
1110
4/10
05
nGCS6
NAND BOOT
SX_TMSSX_TDI
nSCASnSRAS
SX_TCK
I2SSDO_
I2SSCLK_
SX_TDO
I2SLRCK_
CDCLK_I2SSDI_
CM
1210
4/10
05
R61 100/1005
R65 22/1005
R63 22/1005
X1
12MHz
R68 22/1005
X-TAL
LnXDACK1R69 22/1005
LnXDREQ1
CM
1310
4/10
05
MPLL UPLLX-Tal X-Tal
LTDO
VDDRTC
VDDalive
nWBE3
LCLE
LnFRELnFCE
LnFWE
LALE
CM
1410
4/10
05
XMON
nYPONYMONnXPON
LRnBVDD33V
nWBE2
R67 4.7K/1005
CLKOUT1
CM
1510
4/10
05
R21 100/1005
R95 4.7K/1005
CM
1610
4/10
05
TXD0RXD0
SDDATA2_
SDCMD_
TOUT1
SDDATA3_
SDCLK_
SDDATA1_SDDATA0_
CM
1710
4/10
05
nRESETnRST_OUT
CB_CFG
DCLK
ADDR2
UP
LL
MP
LL
HSYNC
VDEN
ADDR4ADDR3
CM
1810
4/10
05
LADDR[14:2]
LADDR6LADDR5LADDR4LADDR3LADDR2
LADDR8LADDR7
ADDR0/GPA0B14
ADDR1D14
ADDR2A14
ADDR3C13
ADDR4B13
ADDR5D13
ADDR6A13
ADDR7C12
ADDR8B12
ADDR9G12
ADDR10D12
ADDR11E12
ADDR12B11
ADDR13A11
ADDR14C11
ADDR15G11
ADDR16/GPA1A10
ADDR17/GPA2B10
ADDR18/GPA3E10
ADDR19/GPA4D10
ADDR20/GPA5F10
ADDR21/GPA6A9
ADDR22/GPA7D9
ADDR23/GPA8E9
ADDR24/GPA9B9
ADDR25/GPA10C9
ADDR26/GPA11E8
DATA0B8
DATA1A8
DATA2D7
DATA3 E7
DATA4C7
DATA5B7
DATA6A7
DATA7 C6
DATA8F7
DATA9B6
DATA10D6
DATA11 A5
DATA12C5
DATA13B5
DATA14D5
DATA15A4
DATA16A3
DATA17B3
DATA18 A2
DATA19A1
DATA20B2
DATA21C3
DATA22 B1
DATA23C2
DATA24C1
DATA25D2
DATA26 D4
DATA27D1
DATA28E3
DATA29E2
DATA30E4
DATA31E1
ALE/GPA18G14
CLE/GPA17H12
R/nBR13
NCONU13
nFCE/GPA22G17
nFRE/GPA20G16
nFWE/GPA19G15 nXDACK0/GPB9
H2nXDACK1/GPB7
G2
nXDREQ0/GPB10H3
nXDREQ1/GPB8H4
nBE0:nWBE0:DQM0A17
nBE1:nWBE1:DQM1B16
nBE2:nWBE2:DQM2C15
nBE3:nWBE3:DQM3 A16
nSCS0:nGCS6F16
nSCS1:nGCS7F17
nSCASC14
nSRAS B15
SCKED16
SCLK0F13
SCLK1F14
G1nXBACK/GPB5nXBREQ/GPB6
G5
nGCS0D17
nGCS1/GPA12E15
nGCS2/GPA13E16
nGCS3/GPA14E14
nGCS4/GPA15E17
nGCS5/GPA16F15
nOEC16
nWAITG13
nWEE13
OM0R14
OM1U15
Address Data
Chip Select
DMA
SDRAM
NAND
U1AS3C2410A-266MHZ
LADDR9
LADDR13LADDR14
LADDR10LADDR11LADDR12
TOUT2
CM
1910
4/10
05
CM
2010
4/10
05
AIN5
AIN0
AIN7
CM2
220/1005
TP1TOUT0
LDATA11LDATA12
VSYNC
LDATA9
LDATA14LDATA13
LDATA8
LDATA15
LDATA10
LDATA22
LDATA18
LDATA20
LDATA17
LDATA19
LDATA27
LDATA25
LDATA21
LDATA23
LDATA16
LDATA31
LDATA24
LDATA29
LDATA26
LDATA28
LDATA30
CM3
220/1005
R74 100/1005
LCD_PWREN
R78 22/1005
AMPEN
R11 100/1005
R14 100/1005R13 100/1005
R238 100/1005R239 100/1005
IICSDAIICSCL
LDATA[31:0]
LDATA0
LDATA7
LDATA3LDATA2LDATA1
LDATA5LDATA6
LDATA4
MPLL
R80 100/1005 PWREN
R9 100/1005
WP_SD_
R12 100/1005
R1 100/1005
R16 100/1005
R20 100/1005
R30 22/1005R2 100/1005
R18 100/1005
R32 22/1005
R34 100/1005
R23 100/1005
R7 100/1005
R33 100/1005
R4 100/1005
R24 100/1005
R31 22/1005
LnWBE3
R6 100/1005
LnWBE2
R5 100/1005
LnWBE0LnWBE1
R22 100/1005
R70 22/1005
VDDMPLLVDDADC VDDMOP VDDIOVDDiarm VDDi
LnGCS2nGCS2
UPLL
R40 22/1005
VDDUPLL
LnGCS6VDD33V
nWBE0nWBE1
LnOEnOE
LnXDACK0
DN1DP1
R58
10K/1005
LSCKELSCLK0LSCLK1
CM
610
4/10
05
L3MODE_
L3CLOCK_L3DATA_
CM
710
4/10
05
R79 22/1005
CM
110
4/10
05
R224 100/1005
R212 100/1005
LnSRAS
R77 100k/1005
PCI
SB_SSTATSB_SCRTL
Title
Size Document Number Rev
Date: Sheet of
MCS01-DB-001 1.0
S3C2410A3
2 7Wednesday , January 27, 2010
SDDATA1SDDATA0SDCMDSDCLK
SDDATA3SDDATA2
VDD33V
R225 100/1005
R227 100/1005R226 100/1005
R213 100/1005
R242 100/1005
TCK
LnSCAS
R3 100/1005R243 100/1005
R15 100/1005
TP4
R43 22/1005R42 22/1005
R47 22/1005
R45 22/1005 R53 100/1005
USB_SUSPEND
AIN2
R214 100/1005TDI
R228 100/1005
TP2
R49 22/1005
VD[23:0]
R44 22/1005 R52 100/1005
R55 100/1005
VD23
VD1
VD9
VD0
VD4
VD15
VD22
VD20VD21
VD12
VD16
VD2
VD17
VD7
VD14
VD6
VD11
VD19
VD3
VD13
VD8
VD5
VD18
VD10
R215 100/1005
nTRST
TDOR81 22/1005
R41 22/1005LnGCS4
nGCS4
LnXDREQ0
R17 100/1005
CB_DCD
R64 4.7K/1005
R50 22/1005
R46 22/1005
R60 100/1005
R54 100/1005
R56 100/1005R48 22/1005
R229 100/1005
R231 100/1005R230 100/1005
TMS
VDD33V
LED_STATUS
R211 100/1005
nCD_SD_
LnWEnWE
USB_WAKEUP R62 100/1005
CB_FAR8 100/1005
CHARGER_INT
R36 100/1005R37 100/1005
R35 100/1005
R39 100/1005R38 100/1005
I2SSCLK
L3CLOCKL3DATAL3MODE
I2SSDOI2SSDICDCLK
I2SLRCKI2SLRCK/GPE0
T5
I2SSCLK/GPE1P5
CDCLK/GPE2N6
I2SSDI/nSS0/GPE3U5
I2SSDO/I2SSDI/GPE4U6
SPIMISO0/GPE11T7
SPIMOSI0/GPE12U7
SPIMISO1/EINT13/GPG5U9
SPIMOSI1/EINT14/GPG6R9
SPICLK0/GPE13P8
SPICLK1/EINT15/GPG7R10
nSS0/EINT10/GPG2T8
nSS1/EINT11/GPG3L9
XMON/EINT20/GPG12 P11
nXPON/EINT21/GPG13U11
YMON/EINT22/GPG14T11
nYPON/EINT23/GPG15M11
EINT0/GPF0N14
EINT1/GPF1N17
EINT2/GPF2M16
EINT3/GPF3M17
EINT4/GPF4M15
EINT5/GPF5M14
EINT6/GPF6L15
EINT7/GPF7L17
EINT8/GPG0R8
EINT9/GPG1U8
VD0/GPC8L1
VD1/GPC9L2
VD2/GPC10L4
VD3/GPC11M3
VD4/GPC12M4
VD5/GPC13M2
VD6/GPC14N1
VD7/GPC15N3
VD8/GPD0N2
VD9/GPD1N4
VD10/GPD2P1
VD11/GPD3P3
VD12/GPD4P2
VD13/GPD5T1
VD14/GPD6R2
VD15/GPD7U1
VD16/GPD8T2
VD17/GPD9R3
VD18/GPD10R4
VD19/GPD11U2
VD20/GPD12T3
VD21/GPD13U3
VD22/nSS1/GPD14T4
VD23/nSS0/GPD15P4
LEND/GPC0J4
VCLK/GPC1J2
VLINE:HSYNC/GPC2J6
VFRAME:VSYNC/GPC3K4
VM:VDEN/GPC4K2
LCDVF0/GPC5K6
LCDVF1/GPC6L6
LCDVF2/GPC7L3
LCD_PWREN/EINT12/GPG4P9
nCTS0/GPH0L14
nRTS0/GPH1L12
TXD0/GPH2K15
RXD0/GPH3 K17
TXD1/GPH4K16
RXD1/GPH5K14
nRTS1/TXD2/GPH6K13
nCTS1/RXD2/GPH7 K12
UCLK/GPH8L16
AIN0 U16
AIN1T15
AIN2U17
AIN3T16
AIN4R15
AIN5T17
AIN6R16
AIN7 N13
VrefN12
TOUT0/GPB0 F2
TOUT1/GPB1F1
TOUT2/GPB2F4
TOUT3/GPB3G3
TCLK0/GPB4 G4
TCLK1/EINT19/GPG11R11
SDCLK/GPE5T6
SDCMD/GPE6P6
SDDATA0/GPE7 R6
SDDATA1/GPE8N7
SDDATA2/GPE9P7
SDDATA3/GPE10R7
IICSCL/GPE14L7
IICSDA/GPE15M8
EXTCLKJ11
CLKOUT0/GPH9R12
CLKOUT1/GPH10U12
MPLLCAPP17
UPLLCAPL13
OM2U14
OM3T13
XTIpllH17
XTOpllH16
EINT16/GPG8U10
EINT17/GPG9T10
EINT18/GPG10P10
nTRSTH5
TCK H6
TDIJ1
TDOJ5
TMSJ3
DN0T12
DP0P13
DN1/PDN0N11
DP1/PDP0M10
XTIrtcP16
XTOrtcR17
SDIO
UART
LCD Control
LCD Data
TSP
USB
IIS
IIC
Timer
External Interrupt
ADC
Clock JTAG
SPI
U1BS3C2410A-266MHZ
VDD33V
R232 100/1005R233 100/1005
R72 100/1005
TXD1RXD1
R51 22/1005
R19 100/1005
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 21/42 www.mcubetech.co.kr
VCC1V8A
R2060/1005
R971.5K/1005
USB JUMPER SETTINGA : USB1.1B : USB2.0
V1 103Z/2KV
R87
10K/
1005
CM
4410
3/10
05
CM
4910
4/10
05
VDD33V
246
135
J3HEADER 3x2/SMD
Title
Size Document Number Rev
Date: Sheet of
MCS01-DB-002 1.0
MEMORY/USBA3
3 7Monday , September 21, 2009
DP2
V2 103Z/2KV
R2070/1005
RR
EF6
AGN
D2
5
DM
4
DAT
A131
AGN
D1
1
DAT
A738
DP
3
RP
U2
VCC(1V8)128
RS
T_N
7EO
T8
DR
EQ9
DA
CK
10D
IOR
11D
LOW
12D
GN
D1
13IN
T14
CS15
DG
ND
329
DAT
A030
DAT
A232
DAT
A333
VCC
IO2
34
DAT
A435
DAT
A536
DAT
A637
DAT
A839
DAT
A940
DG
ND
441
DAT
A10
42
43DATA1144DATA1245DATA1346DATA1447DATA1548VCCIO349VBUS50VCC(1V8)251XTAL252XTAL153VCC154VCC255WAKEUP56SUSPEND
A727
DGND226
A524
A423
A322
VCCIO121
A220
A119
A018
WR17
RD16
A625
57GND
U5ISP1582BS
R86
10K/
1005
VDD33V
+
CT1
4.7u
F/10
V/20
12
R934.7k/1005
LDATA[31:0]
R85
10K/
1005
CM
5310
4/10
05
DP
R10012K/1005
CM
5010
3/10
05
CM
5110
4/10
05
CM
4510
4/10
05
CM
4710
4/10
05
CM
4610
3/10
05
CM
4810
4/10
05
CM
5210
4/10
05
VDD33V
VBUS1
R96100k/1005
R98 22/1005R99 22/1005
VCC1V8A
X3
12MHzCM43
220/1005
CM42
220/1005
LAD
DR
[9:2
]
LADDR5
LADDR9
LADDR3
LADDR8LADDR7LADDR6
LADDR4
VDD
33V
DN1
R84470k/1005
LnWELnOE
LnGCS2
LADDR2
CM
4010
5/25
V/20
12
LnXDREQ1LnXDACK1
USB_WAKEUPUSB_SUSPEND
DN2DP2
nRST_OUT
VBUS2 VBUS1
D-2
D+3
GND04
GND15
GND_F16
GND_F27
GND_F38
GND_F49
10H1 11H2
J2
USB Port B ty pe/MINISMD
CM41104/1005
VDD33V
VBUS
USB(Device)SOCKET
VDD33V
CM
3210
4/10
05
LDATA20
LDATA22
SDCLK_
LDATA28
LDATA31
LDATA26
LDATA23
LDATA21
LDATA19
LDATA30
LDATA25
LDATA29
LDATA24
LDATA27
LDATA18
LDATA16LDATA17
R9410k/1005
SD CARD
SDDATA0_
SDCMD_
DAT29CD/DAT31 CMD
2 VSS13 VDD4 CLK5 VSS26 DAT07 DAT18
nCD10 WP11
PAD1 13
PAD4 16PAD2
14
PAD3 15
SW 12
HOLE2 18HOLE1 17
J5
DM1B-DSF-PEJ/SD CARD SOCKET
VDD33V
SDDATA1_
SDDATA2_
SDDATA3_
CM
3310
4/10
05
SDRAM(64MBYTE)
CM
3410
4/10
05
CM
3510
4/10
05
LDATA9
LDATA6
LDATA4
LADDR24LADDR25
LDATA5
LADDR[25:24] LDATA12
LDATA10LDATA11
LDATA13LDATA14LDATA15
CM
3610
4/10
05
LDATA7
LDATA2LDATA1
VDD33V
VDD33V
LnWBE0
LSCLK0
LnWBE1
LnWELnSCASLnSRAS
LSCKE
CM
3710
4/10
05
LnGCS6
R92
1meg
a/10
05
VBUS2
USB_EOT
CM
3810
4/10
05
LnWBE2LnWBE3
LDATA0
CM
2510
4/10
05
A023
A124
A225
A326
A429
A530
A631
A732
A833
A934
A1022
A1135
BA121
nWE 16nSRAS 18nSCS 19
nSCAS 17LDQM15
UDQM39
SCKE37
SCLK38
VDD2 27VDD1 14
DQ0 2
DQ14
DQ2 5
DQ3 7
DQ4 8
DQ510
DQ6 11
DQ7 13
DQ8 42
DQ944
DQ10 45
DQ11 47
DQ12 48
DQ13 50
DQ14 51
DQ15 53
VDDQ03VSS254 VSS141 VSS028
VSSQ352 VSSQ246 VSSQ112 VSSQ06
BA020
VDD01
VDDQ3 49VDDQ2 43VDDQ1 9
A1236
U2
K4S561632H-UC75/32MBYTE
VCC1V8B
LDATA[31:0]
LDATA3
CM
2310
4/10
05
LDATA8
CM
2410
4/10
05
VDD33V
CM
3910
4/10
05
LADDR25
LADDR[25:24]LADDR24
VCC1V8B
LSCLK1
VDD33V
VDD33V
LnWELnSCASLnSRAS
LSCKE
LnGCS6
nRST_OUT
LDATA[31:0]
VDD33V
42
1
53
U6
74AHC1G08/SOT
A023
A124
A225
A326
A429
A530
A631
A732
A833
A934
A1022
A1135
BA121
nWE 16nSRAS 18nSCS 19
nSCAS 17LDQM15
UDQM39
SCKE37
SCLK38
VDD2 27VDD1 14
DQ0 2
DQ14
DQ2 5
DQ3 7
DQ4 8
DQ510
DQ6 11
DQ7 13
DQ8 42
DQ944
DQ10 45
DQ11 47
DQ12 48
DQ13 50
DQ14 51
DQ15 53
VDDQ03VSS254 VSS141 VSS028
VSSQ352 VSSQ246 VSSQ112 VSSQ06
BA020
VDD01
VDDQ3 49VDDQ2 43VDDQ1 9
A1236
U3
K4S561632H-UC75/32MBYTE
CM
2610
4/10
05
LADDR[14:2]
VBUS1
DP1
USB CLIENT
LADDR12LADDR11LADDR10
R91
1.5K
/100
5
DN
LADDR4
LADDR14LADDR13
LADDR8
LADDR2
nCD_SD_
LADDR7LADDR6
LADDR9
LADDR5
LADDR3
CM
2710
4/10
05
CM
2810
4/10
05
R90
10K/
1005
LADDR[14:2]
R89
10K/
1005
CM
2910
4/10
05
WP_SD_
VDD33V
R834.7K/1005
LRnB
CM
3010
4/10
05
CM
3110
4/10
05
LDATA3
LDATA0
LDATA4
LDATA7
LDATA5
LDATA2LDATA1
LDATA6
LDATA[31:0]
LADDR12LADDR11LADDR10
DP
LADDR4
LADDR14LADDR13
LADDR8
LADDR2
LADDR6
LADDR9
LADDR5
LADDR3
LCLE
LnFWE
LALE
LADDR7
LnFRE
LnFCE
VSS 13
CLE16
ALE17
WE18WP19
I/O029
I/O130
I/O231
I/O332
I/O441
I/O542
I/O643
I/O744
VSS1 36
VCCQ 37
NC 6R/B 7
RE8
CE9
VCC12
U4
K9K1208U0A-48TSOP
NAND FLASH 64MByte
VDD33V
VDD33V
DN
VDD33V
LDAT
A9
LDA
TA10
LDAT
A11
LDAT
A5LD
ATA6
LDAT
A4
LDAT
A13
LDAT
A14
LDAT
A15
LDAT
A12
LDAT
A2LD
ATA1
LDAT
A7
LDAT
A3
LDAT
A0
LDAT
A8
USB_INT
R88
10K/
1005
DN2
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 22/42 www.mcubetech.co.kr
VCC
IO11
20
IO6
6
VAU
X5
GTS
14
GND331
GTS
21
GN
D1
21G
CK0
22G
CK1
23
VCCIO1238
GTS
03
CD
RST
24
GTS
32
DGE28
VCC126
GN
D2
25
GCK227
IO7
7IO
88
IO9
9IO
1010
IO11
11IO
1212
IO13
13IO
1414
IO15
15IO
1616
IO17
17IO
1818
IO19
19
IO2929 IO3030
IO3232 IO3333 IO3434 IO3535 IO3636 IO3737
IO3939 IO4040 IO4141 IO4242 IO4343 IO4444 TDI45 IO4646 TMS47 TCK48 IO4949 IO5050
VCC
IO13
51
IO52
52
IO53
53
IO54
54
IO55
55
IO56
56
VC
C2
57
IO58
58
IO59
59
IO60
60
IO61
61
GN
D4
62
IO63
63
IO64
64
IO65
65
IO66
66
IO67
67
IO68
68
GN
D5
69
IO70
70
IO71
71
IO72
72
IO73
73
IO74
74
GN
D6
75
IO7676
IO7777
IO78 78
IO7979
IO8080
IO81 81
IO8282
TDO83
GND7 84
IO8585
IO86 86
IO8787
VCCIO2188
IO89 89
IO9090
IO9191
IO92 92
IO9393
IO9494
IO95 95
IO9696
IO97 97
VCCIO2298
GSR99
GND8 100
U13
XC2C256-7VQG100
PRT_MOT_CE1
PRT_DI
VDD33V
CM
120
104/
1005
CM195 104/1005
PRT_MOT_CE2
PRT_ERRLED
ANGND
R14910k/1005
VDD33V
PRTPWREN
VPLD
VPLDIO
IO0213 IO0126
IO0412 IO0325
IO0611 IO05
24
IO0810
IO07 23
IO109 IO09 22
IO128
IO1121
IO147 IO13 20
IO166 IO1519
IO185 IO17
18
IO204
IO19 17
IO223 IO2116
IO242 IO2315
IO261 IO25
14
H127
H228
SH129
SH230
J10
10226-1210PE
R120 100/1005 PRT_STB5
PRT_MOT_IN1
B2 MPZ2012S331A
PRT_ERRLED
IICSDA
TP7
Probe Connector
XP_KEY
VDD33V
VDD33V
VPL
D
CM141 101/1005
R122 100/1005 PRT_DI
VPLDIO
XP_AD_CS
VDDaliv eLDATA[31:0]
LDATA1LDATA0
LDATA5LDATA6
LDATA4
LDATA7
LDATA3LDATA2
VAUX
PRT_STB1
R121 100/1005 PRT_STB6
CM197 101/1005
VDD33V
PRT_STB2
R117 100/1005R119 100/1005
IICSCL
R14510k/1005
SX_TDI
VPLD
CM
107
104/
1005
SX_TCKSX_TMS
VDD33V
R134 100/1005
PRT_STB3
KEY3
D5 BAT43WS
TP29
CM
112
104/
1005
XP_DETECTOR
CLKOUT1
CM
105
104/
1005
CM
111
104/
1005
PRT_MOT_IN2
CPLD
VDD33V
VAU
X
CM
113
104/
1005
CM130 101/1005
R124 100/1005
LDATA11LDATA12
R13
510
k/10
05
PRTPWREN
LDATA8
LDATA15
LDATA10LDATA9
LDATA14LDATA13
CM
126
101/
1005
R131 100/1005
PRT_FEEDSW
CM
132
101/
1005
R129 1k/1005
R13
610
k/10
05
18273645
RA3100/AR
VPRE CM193 104/1005
XP_KEY
PRT_MOT_IN2
PRT_MOT_IN1
18273645
RA2100/AR
XP_MOT1_DIRXP_MOT2_STEPXP_MOT1_STEP
XP_MOT2_DIR
LDATA1LDATA0
Printer Connector
CM
108
104/
1005
R13
710
k/10
05
R123 10k/1005
LnOE
R14110k/1005
VDD33V
CM131 101/1005
CM136 101/1005
ANPWR
CM137 101/1005
TP27
CM140 open/1005
CM
128
101/
1005
CM
125
101/
1005
CM
124
101/
1005
PRT_STB4
R132 100/1005
PRT_STB6PRT_STB5
PRT_FEEDSW
ANGND
CM133 101/1005
VDDPRT
CM142 101/1005
R114 100/1005 PRT_STB1
LAD
DR
2
LAD
DR
5LA
DD
R4
LAD
DR
3
R133 100/1005
PRT_PAPER
R126 100/1005R125 100/1005
R14810k/1005
VDD33V
MA+1
MB+2
MA-3
MB-4
VH15
VH26
DO7
LAT8
CLK9
VDD10
STB111
STB212
STB313
TM14
PGND115
PGND216
PGND317
PGND418
STB419
STB520
STB621
DI22
VH323
VH424
LGND25
VF26
CO27
J9
10022HS-27
LADDR[5:2]
LADDR2
LADDR5LADDR4LADDR3
XP_AD_CSXP_AD_SCLK
PRT_MOT_CE1
PRT_MOT_CE2
ANGND
R130 10k/1005
Title
Size Document Number Rev
Date: Sheet of
MCS01-DB-004 1.0
PROBE/PRINTER/KEYA3
5 7Wednesday , January 27, 2010
VDD33V
LDATA2LDATA3
LDATA5
VPL
DIO
LDATA4
CM
118
101/
1005
CM134 101/1005
XP_MOT_LIMIT
R113 100/1005 PRT_CLK
CM139 101/1005
CM
106
104/
1005
XP_AD_SDATA
XP_SCAN_EN
XP_PULSER_DAMP
XP_PULSER_PINXP_PULSER_NIN
XP_TCG_SHUNT
CM
115
104/
1005
IN211 NC210
OUT4(B-)12
NC19
OUT3(B+) 14
SGND7
VS213
PGND18
CE12
VCC1
OUT1(A+)3
VS14
OUT2(A-) 5
IN16
PGND216
CE215
U12 KA3100D
+
CT
510
uF/1
0V/2
012C
M14
710
4/10
05
KEY
KEY3
nRST_OUT
1 342
S3
1105 SABM-10T
1 342
S1
1105 SABM-10T
1 342
S4
1105 SABM-10T
1 342
S2
1105 SABM-10T
18273645
RA4100/AR
PRT_DO
PRT_DO
PRT_CLKPRT_LAT
PRT_PAPER
CM
116
104/
1005
R111 100/1005
CM
148
104/
1005
VPLDIO
R112 100/1005 PRT_LAT
CM198 101/1005
CM
127
104/
1005
VDDPRT
B3MPZ2012S331A
TP9 TP10
VDD7V2
N12N7002
R14
647
0k/1
005
MOTPWR
XP_DETECTOR
MOTGND
R14
347
0k/1
005
CM
144
104/
1005
Printer Power
LDATA7LDATA6
CM
117
104/
1005
XP_AD_SCLK
CM
150
104/
1005
SX_INT
VDDPRT
VDDPRTVDD33V
PWR_KEY
ANPWREN
R14210k/1005
+
CT
610
0uF
/16V
/734
3
VDD33V
CM
149
104/
1005
LDA
TA1
0
LDA
TA1
3LD
AT
A12
LDA
TA9
LDA
TA1
1
LDA
TA1
5
LDA
TA8
S11
S22
S33
G4
D45D3 6D27D18
P2
SI9433DY
LDA
TA1
4
MOTPWRENXP_SCAN_EN
18273645
RA1100/AR
XP_PULSER_PINXP_PULSER_NIN
CM138 101/1005
CM129 101/1005
XP_MOT2_DIR
XP_MOT1_STEPXP_MOT2_STEP
XP_MOT1_DIR
12345
J19
12512WS-05A00
R115 100/1005
KEY2
KEY0
PRT_STB2
CM
146
104/
1005
R128 100/1005
CM
123
101/
1005
CM
122
101/
1005
VPLDIO
CM
121
101/
1005
CM
109
104/
1005
CM
110
104/
1005
S11
S22
S33
G4
D45D3 6D27D18
P3
SI9433DY
SX_TDO
VDD33V
CM
143
104/
1005
ANPWR
ANGND
XP_MOT_LIMIT
D6 BAT43WS
R116 100/1005
XP_TCG_SHUNTXP_PULSER_DAMP
PRT_STB3
AIN0
VDDPRT
R247 300/1005
PRT_PWRLED
CM194 104/1005
LnGCS4LnWE
PRT_PWRLED
CM
119
101/
1005
VPLDIO
R127 10k/1005
KEY1
XP_AD_SCLKXP_AD_SDATA
XP_AD_CS
TP28
R248 300/1005
TP8
CM
114
101/
1005
N22N7002
R14
747
0k/1
005
CM
145
104/
1005
R14
447
0k/1
005
Analog Power
ANPWRENKEY2KEY1KEY0
18273645
RA5100/AR
R118 100/1005 PRT_STB4
LnXDACK0LnXDREQ0
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 23/42 www.mcubetech.co.kr
VDDaliv e
R217 4.7k/1005
TP25
THM
D12MDC30354
TP17
MOTPWR
DCIN
B9
MPZ2012S331A
B7MPZ2012S331A
R18510K/1005
N52N7002
R19
747
0k/1
005
R19
647
0k/1
005
CM
186
104/
1005
+
CT
3610
uF/1
0V/2
012
B14 MPZ2012S331A
BATSMB
N42N7002
S11
S22
S33
G4
D45D3 6D2 7D1 8
P13
SI9433DY
R18
747
0k/1
005
R191100k/1005
R19
047
0k/1
005
+
CT3
110
0uF/
16V/
7343
P11FDS6679Z
PWR_KEY
TP19
TP18
VIN1
2
ON/OFF
VOUT 3
4
GND
U21 MC33375ST-3.3
CM
170
104/
1005
CM
169
104/
1005 +
CT2
910
0uF/
16V/
7343
+
CT2
810
uF/1
0V/2
012
VDD7V2
B10MPZ2012S331A
B11
MPZ2012S331A
1
ENIN2
GN
D3
OUT 4
FLAG 5
THM
6
U20
MIC29302BU
TP16
R17
847
0k/1
005
R194100k/1005
+
CT2
610
uF/1
0V/2
012
CM
167
104/
1005
SMBDAT
R18
010
0k/1
005
CM
168
104/
1005+
CT2
710
0uF/
16V/
7343
VPRE
VDD7V2
1
ENIN2
GN
D3
OUT 4
FLAG 5
THM
6
U24
MIC29302BU
R19210k/1005
CHARGER_INT
TP21
0
0
CM
188
104/
1005 +
CT3
710
uF/1
0V/2
012
CM192
open/1005
+
CT3
810
0uF/
16V/
7343
VDDRTC
R21910K/1005
R198 WSL2512/0.01/1%
CM
190
104/
1005
CM
189
101/
1005
TP20
R200 open/1005R201 open/1005
VDD33V
0
VS- 1
VCC 2
FIL 3
VEE 4VOUT5 A26 A47 VS+8U25
LT6100
P5FDS6679Z
D11
MMSD4148
TP26
R204100/1005
DLO
+ CT32
22uF/16V/3528
+CT33
22uF/16V/3528
CM166
104/1005
VPRE
CM171
104/1005
R18122/1005
AIN2
CM
191
104/
1005
CM175
103/1005
TP22
12
F1
miniSMDC260F12+CT24
22uF/16V/3528
REF
CM
187
104/
1005
D13MMSZ4678T1
PDS
IICSCLIICSDAG11
S22
G23
D24
S1 5D1
6P15
FDC6302P
R179 WSL2512/0.01/1%
CM
178
104/
1005
123
56
478
J17
MQ172
0
SRC
+CT23
22uF/16V/3528
TP38
R2444.7k/1005
R18810k/1005
THM
VDD_CORE VDDi
VDDMPLL
VDDUPLL
VDDiarm
L4
SDS0604-220M
VDD33V
CM183104/1005
R20520k/1005
VDDADC
VDDIO
VDD33V
VDDMOP
SMBDAT
nACOK
Probe Motor Power
LOAD
SMBCLK
S11
S22
S33
G4 D4 5D3 6D2 7D1 8P14
SI9433DY
VDD33V
BT1CR2032_SOCKET
ALIVE
Vf use
B13MPZ2012S331A
Green
VIN1
2
ON/OFF
VOUT 3
4
GND
U23
MC33375ST-1.8
CM
185
104/
1005
CM
184
104/
1005
VDD_COREMOTPWREN
Power LED
0
TP14 TP15
0
SRC
R21610k/1005
Red
G11
S22
G23
D24
S1 5D1
6P16
FDC6302P
CHARGER
VDD33V
0
VDDalive
CM165
104/1005
CM172105/25V/2012
DCIN
PWR_OUT
MOTGND
B16MPZ2012S331A
B-1 T2 D3 C4 B+5
H1 6H2 7
J18
505601MR005XX00XX
TP23TP24
CM181
103/1005
0
R18222/1005
LDO
CM173
105/25V/2012
CM174
104/1005
R189WSL2512/0.01/1%
R184 0/1005
DLO
+CT30
2.2uF/20V/3516
R2454.7k/1005
0
N3
FDS6670S
nACOK
CM182
105/25V/2012
PDL
SMBCLK
R2464.7k/1005
TP31
CSIP 21
IMAX 10
PDS
31THM13
REF 4
GN
D1
5
VMAX 9
BATT 19
PDL 30
DH
IV25
DAC11
QG
ND
33
I.C.17
DLO 23
INT16
PGND 22
DLOV 24
LDO2
CSIN 20
DHI 26
CCS6
CCI7
CCV8
CSS
N28
CS
SP29
DCIN1
SRC27
ACIN3
ACOK32
VDD12
SDA14
SCL15
GN
D2
18
U22
MAX1535B/TQFN
LDO
CM
179
104/
1005
VDDRTC
R19
951
k/10
05R
202
12k/
1005
VPRE
MOTGND
Title
Size Document Number Rev
Date: Sheet of
MCS01-DB-006 1.0
POWERA3
7 7Wednesday , January 27, 2010
+CT25
22uF/16V/3528
IMAGE
LOAD
Vf use
R2031k/1005
CM176
103/1005
BATSMB
R218open/1005
VDD33V
VDD33V
BATT
P6FDS6679Z
R186 10k/1005
R193100k/1005
VPRE
+
CT3
410
uF/1
0V/2
012
D10
MMSD4148
+
CT4
310
uF/1
0V/2
012
MOTGND
CM180
104/1005
P9FDS6679Z
CM177
103/1005
VDD7V2
R1954.7k/1005
R183100K/1005
+
CT3
510
0uF
/16V
/734
3
0
VDD7V2
IICSCL
IICSDA
D9 RB160L
PWREN
B12 MPZ2012S331A
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 24/42 www.mcubetech.co.kr
4 Device Setup 4.1 Installing or Removing the Battery
The battery is installed in a bay in the BioCon-700. When you are changing the battery or removing the battery for storage, follow these instructions.
Power off Turn the system off.
Disconnect accessories Disconnect all connections from the console.
Loosen the two screws using a screwdriver.
Remove the battery cover. IMPORTANT: When removing the battery cover, be careful to not bend the cover.
Pull out the battery using the strap on the battery.
Insert the new battery. When inserting, the top side of the battery (the side having LED) should be up (facing the bottom of the unit) and the strap on the battery should be in the right. The battery cannot be properly installed if the orientation is incorrect.
WARNING: To avoid the risk of explosion, only use batteries recommended
by Mcube Technology. CAUTION: Never use excessive force to install the battery.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 25/42 www.mcubetech.co.kr
4.2 Changing the Thermal Paper
1) Open the printer cover as shown to the left.
2) Pull out the empty bobbin.
3) With the printer paper in one hand, unroll a
small length of the paper and insert into the
unit as shown.
4) Close the printer cover after inserting the
paper.
CAUTION: Be sure to insert the paper in the correct orientation. To avoid damaging the system:
- Only use thermal paper recommended by Mcube Technology. - Only print when the thermal paper is correctly loaded.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 26/42 www.mcubetech.co.kr
4.3 Charging the Battery Module of the BioCon-700
Connect an AC cord to a DC adapter.
The picture shows an adapter with the AC cord properly connected.
Connect the DC jack to the adapter terminal of the console. *Direction of the DC jack: Check the direction of the DC jack.
The picture shows a console with the proper connection to the DC jack.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 27/42 www.mcubetech.co.kr
Connect the AC plug to a socket.
Check the color indicator on the console. *Green in power indicator: Tells that the adapter connected and AC power is present. The system is ready to charge and be operated. *Yellow in power indicator: Denotes that the device is charging. When the battery is fully charged, the yellow indicator turns green. *Fully charging the battery may take up to approximately 6 hours..
WARNING:
Only use AC/DC Adapters recommended by Mcube Technology.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 28/42 www.mcubetech.co.kr
4.4 Connecting the Probe to the System
1. Check the direction of the probe connector as shown in the left picture.
2. Align the probe cable to the probe terminal. After aligning, push the probe cable straight in until there is a click sound.
* To disconnect the probe from the console, push the relief clamps marked by arrow on the probe connector and pull out.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 29/42 www.mcubetech.co.kr
4.5 Assembling the Rolling Cart Refer to “Rolling Cart Assemble Manual(MRC_BioCon_700)” for assembling instructions of a optional rolling cart.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 30/42 www.mcubetech.co.kr
4.6 Calibration There are two methods for the calibration. Following table shows the calibration process.
Step CalKit Calibration Phantom Calibration 1 Open the cap of the calibration kit and
pour saline solution up to the fill-mark of the calibration kit. Confirm that the air bubble is absent. You can also the pure water on behalf of the saline solution. But in this case, do calibration after confirming that all the air bubbles went away.
Place the CubeScan phantom on a flat surface. And open the cover of the phantom.
2 Close the cap of the calibration kit.
Drop about 5ml water to the center surface of the phantom.
3 Align the probe scan button with the arrow mark of the calibration kit, and put the probe head into the probe holder firmly.
Place the holder on the top of the Cubescan phantom. Check if the holder is in a stable and flat position.
Put the probe head into the probe holder firmly.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 31/42 www.mcubetech.co.kr
4 Connect the probe to the device. 5 Turn the device on. 6 Touch the Setup icon in the Top Screen.
7 Touch the following icon in the Setup Screen.
SCANSCAN
8 Touch the following icon in the Setup
Scan Screen.
Touch the following icon in the Setup Scan Screen.
9 Wait until the calibration is completed. If calibration is done successfully, the calibration date will be changed. If calibration error is occurred during calibration, contact a local distributor or Mcube Technology.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 32/42 www.mcubetech.co.kr
5 TROUBLESHOOTING 5.1 Troubleshooting
Error message Description Actions
BATTERY LOW!!! Battery low
Use again after charging the battery. IMPORTANT: To lengthen lifetime of the battery charge the battery when battery capacity is around 20%.
NO PAPER! Printer error
1. Check if the cover of the printer is open. If the cover is open, close the cover and try printing again. 2. Check if the thermal paper is empty. If there is no paper, insert a new roll paper and try printing again. 3. After the above actions the same trouble happen, contact authorized technical center.
NO SCANHEAD! connection error
Check if the connection between the probe-terminal in a console with the probe connector is firm. If the trouble is continued even in a proper connection, contact authorized technical center.
!ERROR! !IN CABLE
CONNECTION!
Transducer circuit open
Contact a local distributor or authorized technical center.
Mismatched Ultrasonic Probe!
Wrong probe attachment
Contact a local distributor or authorized technical center.
No SD card! No SD card installed in a SD card slot
Use after installing the SD cart to the SD card slot.
Unformatted card! Use of
unformatted card.
Use after formatting(FAT32)
Wrong file name Invalid
character as a file name
Use valid character as a file name. Do not use following characters as a file name. \ / : * ? “ < > |
Failure in reading Read error in SD card
Try after reformatting the SD card or use another SD card.
Failure in writing! Write error in SD card
Try after reformatting the SD card or use another SD card.
Abnormal probe motor !
Angle motor error
Contact a local distributor or authorized technical center.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 33/42 www.mcubetech.co.kr
5.2 Message for alert
Message Description Delete this file? Check for the file deletion.
The data has been saved “Filename”
To notice that the data is saved as a “Filename”
Recorded the file exist Do you re-record voice?
When there is a annotated voice recording to the current data.
Cannot find the file! There is no file with that name Duplicate file name There is a file with same name.
Not enough space in SD card! There is not enough space in SD card. Too long name! Too long file name. (up to 255 characters)
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 34/42 www.mcubetech.co.kr
6 MAINTENANCE 6.1 Battery Care
Do not overcharge the battery and avoid deep discharges. To lengthen the battery’s lifetime, use the system while the battery is between 25%~75%. The BioCon-700 does draw power from the battery even while powered off. To avoid deep discharge, disconnect the battery from the system if it will not be used for more than a week. When storing the battery, pre-charging to about 75% is recommended.
6.2 Changing the Battery Modules
See 4.1 “Installing or removing battery”
6.3 Changing the Thermal Paper See 4.2 “Changing the thermal paper”
6.4 Cleaning & Disinfection 6.4.1 Cleaning
1) Cleaning outer case (housing) of the system a) Wipe the main body 1~2 times using soft cloth dampened with isopropyl
alcohol or any other appropriate hospital cleaning solution.. Do not allow liquids to leak into the device while cleaning..
b) Thoroughly dry the device with a clean, soft cloth before re-deployment.
2) Cleaning the probe Since the surface of the Probe affects the result of data, users should keep
as follows; a) Before you using the device, you have to wipe out the probe cap cleanly
4~5 times by using soft cloth which was dampened with isopropyl alcohol or an appropriate hospital cleaning agent. Then you can use the device after drying with a dry, clean cloth.
b) Apply gel on the top of probe, position the probe on the abdomen of patient, and start scanning.
c) Try to scan at least 2 ~ 3 times to get more accurate results. d) Remove and re-apply gel after scanning 4 ~ 5 times, to scan again. e) Remove the residual gel on the probe’s surface after scanning finished. f) Move carefully not to drop the probe off.
WARNING: To avoid electric shock disconnect the system
from the AC mains and the battery. CAUTION: Do not immerse the console or the probe.
Do not use harsh, corrosive chemicals (e.g. hydrochloric acid, bleach).
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 35/42 www.mcubetech.co.kr
6.4.2 Disinfection 1) Disinfection of the Probe
a) Clean the Probe prior to disinfection. b) Dampen a soft cloth with disinfected solution listed in the table below. c) Wipe the probe with a dampened cloth. d) Air dry or towel dry with a soft, clean cloth. e) Inspect the Probe and the cable for any damage such as cracks.
WARNING: To avoid electric shock disconnect the system
from the AC mains and the battery CAUTION: Do not immerse the console or the probe.
Disinfectants Lists for the Probe disinfection Use any glutaraldehyde based disinfectant to disinfect the Probe. Following table lists compatible disinfectants.
Disinfection Solutions Type Country of Origin Manufacturer Cidex Liquid USA Johnson & Johnson Cidex 7 Liquid USA Johnson & Johnson Metricide 14 Liquid USA Metrex Research Inc. Metricide 28 Liquid USA Metrex Research Inc.
CAUTION: Do not use Cidex Plus or Metricide Plus 30 to
disinfect the device. Cidex Plus or Metricide Plus 30 will attack and damage the plastic enclosure. This will be considered as abuse and will void the warranty.
6.5 Weekly Inspection
a) Try to scan with the probe disconnected, check if the “NO SCANHEAD” message is displayed on the main display.
b) Thoroughly inspect the probe for cracks or leakage. c) Inspect the probe cable for any damage. d) When scanning, check for any abnormal noise emanating from the probe
head. 6.6 Device Repair
Faults not described in section “6. Troubleshooting” are intended to be serviced by a certified technician. In the event a situation outside of those described in the section occurs, contact an authorized servicer or Mcube Technology for servicing.
6.7 Disposal
The device and accessories may contain environmentally hazardous materials (mineral oil, lead, battery pack, etc). When they have reached the end of its useful service life, return them to the Mcube Technology, or follow your local regulations for hazardous waste disposal.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 36/42 www.mcubetech.co.kr
7 SPECIFICATIONS
7.1 Symbol Directory
Symbol Description
Type BF patient applied part (B= body, F= floating applied part)
Attention, see the User guide.
Direct current(DC)
Alternating current(AC)
IPX1 Degrees of protection against the ingress of water.
CE marked in accordance with the Medical Device Directive
UL classification mark for Canada and the U.S.
Collect separately from other household waste (see European Commission Directive 93/86/EEC). Refer to local regulations for disposal.
Date of manufacture
Reference number
Serial number
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 37/42 www.mcubetech.co.kr
7.2 Specification of Components Item Features
Power
AC/DC Adapter: - Model: JMW128 KA09XXXXX
Input: AC 100-240V~, 50-60Hz Output: DC 9Vdc, 3A
- Comply with UL 60601-1. - Only use adapters supplied by MCube Technology.
Battery
- Battery Pack: Li18S Battery cell: Li-ion rechargeable (2P-2S) - Scan: approximately 2400 scans** - Charging time: Fully charging a completely discharged battery may
take up to approximately 6 hours.
Ultrasound Probe
- sector scan - 2.6MHz ultrasound frequency - B-mode scan image - scan angle : 120° - water resistance: rated at IPX1(only probe)
Transducer - Diameter: 10mm - Resonant frequency:2.6MHz - Bandwidth: minimum 40% at 6dB - Penetration depth(normal patient): 18cm
Thermal printer - Built in(57mm width)
Display - 7" TFT LCD - WVGA(800×480 pixels) - 16.7 million colors
Range - Bladder volume range: 0 - 999ml - Accuracy*: ±15%,±15ml (0 - 999ml)
External Interface - USB 2.0 basic
Classification of protection against
electric shock - ClassⅡ equipment - Type BF equipment
Water resistance - Main body(Console): Ordinary equipment - Probe: rated at IPX1
Mode of operation - Continuous operation.
Dimension - 66(L)×202(W)×130(H) mm
Language - English
* Accuracy: According to the scanning instruction, and scanning on a Mcube Technology tissue-equivalent bladder phantom.
** Battery operation time: - For a new battery module fully charged - Tested on Mcube Technology’s test conditions
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 38/42 www.mcubetech.co.kr
8 ENVIRONMENTAL CONDITIONS
8.1 BioCon-700 8.1.1 Operating conditions
Condition Description
Ambient temperature range +10 – +40℃ (+50 - +104℉)
Relative humidity +30% – +75% non-condensing
Atmospheric pressure range +700hPa – +1060hPa
8.1.2 Storage and transport conditions
Condition Description
Ambient temperature range -10 – +60℃ (+14 - +140℉)
Relative humidity +20% – +80% non-condensing
Atmospheric pressure range +600hPa – +1060hPa
CAUTION: If you are not using this device more than a week, please disconnect battery from the device. Store the battery in accordance with the recommended conditions.
Service Manual for BioCon-700
Mcube Technology Co., Ltd. 39/42 www.mcubetech.co.kr
8.2 Battery Module
8.2.1 Battery Storage Conditions
Condition Description
Ambient temperature range -10 – +30℃ (+50 - +86℉) ≤ 1 Year -10 – +45℃ (+50 - +113℉) ≤ 3 Month -10 – +60℃ (+50 - +140℉) ≤ 1 Month
Relative humidity +20% – +80% non-condensing
Atmospheric pressure range +600hPa – +1060hPa
CAUTION: Prior to storing the battery, charge it to about 75%.
Units 22-2460-66 Richmond Road,
Keswick 5035, South AustraliaTelephone: 8351 1455
Facsimile:8293 7377Email: [email protected]
www.implox.com