The Voltage Intensifier Circuit

7/28/2019 The Voltage Intensifier Circuit

1/20

1/1/10 8:27 AMements Themeset

Page 1 of 20ttp://www.waterfuelcell.org/Voltage%20Intensifier%20Circuit.html

The Voltage Intensifier Circuit

(Under Construction)

Stanley Meyer Developed the Voltage Intensifier Circuit (VIC) this in my opinion is a enhanced version behind the GasVoltage control circuit.

The voltage interferer circuit is more efficient but needs a higher level of understanding to successfully replicate.

Remember also that as I have said before patents are definitely not a blue print and specific key areas are left unexplainedto some degree.

I will try to section certain areas of the VIC and explain the operation in as much detail as I can. I will also try to shed new

light and theories on certain areas and how they might function.

I will also include my opinion on the parameters needed and give reference information where possible.

Please download Patent 4,936,961- "Method of the production of a fuel gas" and read through it then assess the

information I will provide below. Download Patent.

The Voltage Intensifier circuit(Diagrams from Patent)

The Molecule Voltage Breakdown
http://www.waterfuelcell.org/index.htmlhttp://www.waterfuelcell.org/Equipment.htmlhttp://www.waterfuelcell.org/index.htmlhttp://waterfuelcell.org/WFCprojects/Stanley%20Meyer%20Patents/wfc-patents/4936961.pdf


2/20



The Water Capacitor

The Hydrogen Fracturing Process (Technical Brief) Book Information

Some of the information and diagrams from now on below have been sourced from the Technical Brief. The Information anddiagrams have been gathered from different sections, these are......

section 1 ( WFC Hydrogen Fracturing process)

section 3 (Hydrogen Gas Management System)

section 7 (VIC Matrix Circuit)

I think they both offer information relating directly to the function of the Voltage Intensifier Circuit for Enhanced Gas


3/20



Generation even though section 7 is specifically for the instant explosion of water mist through an injector.

The reference information can be downloadedhere (forum)

The Hydrogen Fracturing Process (Technical Brief) Book - 7-20Figure 7-8 : VIC Matrix Circuit
http://waterfuelcell.org/phpBB2/viewforum.php?f=6


4/20



My Revised Drawings Of The VIC

(Brief Summary still under construction)


5/20



Voltage Intensifier Circuit Sectioned Analysis

(under construction)

Frequency and Duty cycle

Quote form patent

"Resonance in the circuit was achieved at a 26 volt applied pulse to the primary coil of the torroid at 0KH.sub.z"

This is actually a typo in the patent I think? it should read ...............the toroid at 10khz,sub.z

Quote from the Hydrogen Fracturing Process - Technical Brief reference page 3-16

"The established resonant frequency is most generally in the audio range from 1khz up to and beyond 10khz and is

dependent upon the amount of contaminate in natural water."


Diagrams


6/20




7/20



My thoughts

Frequency range and duty cycle - 1 to 100khz and 1 to 99% duty cycleVoltage amplitude - 1 to 12 volt (output pulse generator)Gate time - 0 to 10sec maybe more?

Transformer

Patent Quote

"In the Example of a fuel cell circuit of FIG. 1, a water capacitor is included. The step-up coil is formed on a conventionaltorroidal core formed of a compressed ferromagnetic powdered material that will not itself become permanentlymagnetized, such as the trademarked "Ferramic 06# "Permag" powder as described in Siemens Ferrites Catalog,CG-2000-

002-121, (Cleveland, Ohio) No. F626-1205. The core is 1.50 inch in diameter and 0.25 inch in thickness. A primary coil of200 turns of 24 gauge copper wire is provided and a coil of 600 turns of 36 gauge wire comprises the secondary winding."

"Resonance in the circuit was achieved at a 26 volt applied pulse to the primary coil of the torroid "

Important note

Well that's only a step up transformer of 3 times = 78 volts, so how do we get higher voltage as stated in the patent (1000volts) across the Cell.????

Maybe the primary was pulsed with around 200 volts giving a output on the secondary of around 600 volts and then theinductor doubled the voltage across the cell? I will explain how the inductor does this in the next section - Anode Inductor


8/20



(step charging).


Diagrams

My thoughts

Design the step up transformer capable of frequency range at least to 100khzDesign the transformer to step up voltage to a minimum secondary output of 500voltsThe transformer might consume 4 amp so transformer secondary and VIC may have to be designed to cope with this

load.

Anode Inductor (step charging)

Patent Quote

"As the stepped-up pulse enters first inductor (formed from 100 turns of 24 gauge wire 1 inch in diameter), anelectromagnetic field is formed around the inductor, voltage is switched off when the pulse ends, and the field collapses

and produces another pulse of the same polarity; i.e., another positive pulse is formed where the 50% duty cycle wasterminated. Thus, a double pulse frequency is produced; however, in a pulse train of unipolar pulses, there is a brief time

when pulses are not present.

By being so subjected to electrical pulses in the circuit of FIG. 1, water confined in the volume that includes the capacitor

plates takes on an electrical charge that is increased by a step charging phenomenon occurring in the water capacitor.Voltage continually increases (to about 1000 volts and more) and the water molecule starts to elongate. "

Important information


9/20



see this link here that explains the way voltage is increased through a positive pulsed - diode, inductor and capacitor

circuit. current is kept moving because of the collapsing field. That is the only thing that should be noted from the link, theother information is mostly irrelevant to our needs.

also here writes how voltage is step up without a transformer using an inductor!

Quotes from the Hydrogen Fracturing Process - Technical Brief
http://www.geocities.com/CapeCanaveral/Lab/5322/ind-kick.htmhttp://www.richieburnett.co.uk/dcreschg.html


10/20



Quotes from the Hydrogen Fracturing Process - Technical Brief 7-3

Diagrams


11/20



Important Note


12/20



Notice on the graph below how the step charging gradually levels out? It follows a Resistor capacitor universaltime constant curve.

Important note

Also note in the diagram above figure (1-4) the voltage on the gate pulse is not fully switched off this may be a necessity tosustain resonance. I don't know?

Quote from the Hydrogen Fracturing Process - Technical Brief pg - 7-7



13/20



My thoughts

Pulse inductor and identify step charging with an oscilloscope or calculate it somehow to come to approx value thentune into it.

Measure voltage with high voltage probe and oscilloscopeApply gate time to regulate gas flow

Cathode inductor(current restriction due to inductance reactance)

Patent

Stan is careful in the patent not to talk about this very important part of the circuit, this is probably the most importantpart to the technology!!!

frequency of the pulse generator is tuned into the point where the inductor restricts the most amount off current.

This is because inductors does not like high frequency pulses and they restrict current and at certain frequency can block

current nearly completely. This is because of the inductive reactance.

Read more here. I know the links refer Alternating current at a certain frequencies but it would probably occur with dcpulses aswell, more testing/experimenting needs to be done.

link 1

chokes

calculator

IMPORTANT QUOTES

Quotes from the Hydrogen Fracturing Process - Technical Brief 3-10

From the Hydrogen Fracturing Process - Technical Brief pg Appx B 01

Quote from the Hydrogen Fracturing Process - Technical Brief
http://home.new.rr.com/trumpetb/audio/XLXCjs.htmlhttp://www.electronics-tutorials.com/basics/chokes.htmhttp://www.ndt-ed.org/EducationResources/CommunityCollege/EddyCurrents/Physics/selfinductance.htm


14/20





15/20





My thoughts

Measure current entering the cell

Due to the Inductive reactance pulse the inductor until minimum current enters the cellMaybe have it variable to make fine adjustments

Water Capacitor


16/20



Patent Quote

"In an example of the circuit of FIG. 1 (in which other circuit element specifications are provided above), two concentriccylinders 4 inches long formed the water capacitor of the fuel cell in the volume of water. The outside cylinder was 0.75

inch in outside diameter; the inner cylinder was 0.5 inch in outside diameter. Spacing from the outside of the inner cylinderto the inner surface of the outside cylinder was 0.0625 inch."

Remember when I give these quotes I'm not saying this is the only way to do it! patents just give bare bones information

this is probably bordering on the minimum requirement to see any effect. That's why you have to look a little deeper. Hereis some more info I found in the hydrogen fracturing book (technical brief)

Quote from the Hydrogen Fracturing Process - Technical Brief

Diagrams


17/20



My thoughts

Initially try submerging tubes in water when testing the VICAlternatively, insulate the tube and do not submerge in water but fill it up with water

If that doesn't work try to make it smaller to lower the capacitance

Electron Bounce

I have not yet come had time to understand this. If anyone has any ideas?


18/20



Diagrams


19/20



My thoughts

not yet understood?

Resonant action (High gas yield)

Stanley Meyer Identified two stages of gas production these are

Electrical Polarization process (minimal gas yield))

Resonant gas production (high gas yield)

I feel that resonant frequency in the VIC is the condition when you achieve step charging across the capacitor at a high

voltage levels and the inductance reactance of the cathode inductor is adjusted with either pulse frequency or inductanceis varied to restrict electron flow.

for a more in depth explanation on what occurs and voltage level leading to and during resonant action see here and here

this will help you tune to resonance

also here is some more information that will help

Quote from the Hydrogen Fracturing Process - Technical Brief pg 1-3

Quote from the Hydrogen Fracturing Process - Technical Brief pg 3-17

Michel, a researcher in France the has presented a preliminary report on his efforts to replicate the VIC and can be seenhere
http://www.waterfuelcell.org/Michel.htmlhttp://www.waterfuelcell.org/Experiment%20objectives.htmlhttp://www.waterfuelcell.org/concept.html


20/20


Another researcher is working hard on a controller and transformer that will give the necessary capabilities to tune the

WFC to resonance. more soon

To discuss this further please visit the forum here.
http://waterfuelcell.org/phpBB2

Documents

The Voltage Intensifier Circuit