The user manual - IFB Appliances · Read the manual carefully before using the chimney CALL ONLY IFB AUTHORISED PERSON TO SERVICE YOUR CHIMNEY & USE ONLY GENUINE SPARES IF IN ANY

If any protective film is fixed on the product please peel off before using the product

Read the manual carefully before using the chimney

CALL ONLY IFB AUTHORISED PERSON TO SERVICE YOUR

CHIMNEY & USE ONLY GENUINE SPARES IF IN ANY CASE IT'S

REQUIRE

India's Finest BrandTrusted by millions

The user manual

CHIMNEY

www.ifbappliances.com


IFB-印度说明书编码：3070500647备注：20150117更新

Trusted by millions

General Information Please read carefully

This chimney is suitable to install on any rigid vertical space, over a gas or electric hotplate &

can be used either in Internal Recirculation mode or outside ducting mode depending on the

model . The installation must be carried out by qualified & competent person or IFB

authorized person with the thorough knowledge of the parameters concerning the evacuation

of the contaminated air. (In conformity to the rules concerning the evacuation of

contaminated air if any as of now or in future). The company disclaims all liability for any

damage or injury caused as a result of not following the Instructions for installation contained

in the text.

1

Dear customer,

We welcome you to the proud IFB owner club.

You have just purchased one of the products from our wide range. We thank & congratulate

you for your choice, expressing trust for IFB. We are convinced that, as time goes by, you will

agree your trust was motivated. The rigour quality standard we have set for our complete

range of the products from Washing machines/Cloth Dryers/Dishwashers/Microwaves ovens

Air conditioner & Refrigerator for Domestic use & Industrial Dishwashers & Launderette

for commercial use at Hotels, Restaurants, Canteens & Housing complexes. IFB is a trusted

brand,known for user friendly & convenient products, designed to combine technology and

simplicity besides Great Looks & Unbeatable Performance.

With IFB chimney you would enjoy every day, to make delicious food for your family with

out any hassle & will keep you as fresh as before the cooking, because IFB chimneys quickly


COMPONENTS

The chimney (Cooker Hood) is made up of the following components (fig. 1):Hood canopy Complete (control switches, Lighting, Motor with Rotor & blower Box )

Duct Cover Low & Upper (model wise) glass/ Filter

2

Reducer for φ120 out-let

Upper duct cover hook

Upper duct cover

Low duct cover

Blower box assembly

Glass

Filter



Upper duct cover

Hood hook

Low duct cover

IFB -GS-60T-PL/90T-PL IFB -GL- 6 P-60CM/90CM

Blower box assembly

Filter

Hood hook

25

Customer Copy

Product………………………Model ……………………… Serial No ………………........

CustomerName ………………………………………………………………………….........

Address …………………………………………………………………………………..........

Area …………………………………………………… City …………………………...........

State……………………………………….Pin Code…………………………………….......

Telephone No. - Residence…………………………. Mobile………………………….........

E-mail……………………………………………………………………..............................

Dealer'sName ………………………………………………………………………...............

Invoice No. & Date……………………………………. Price………………………….........

Machine Delivered on………………………Machine Installed On………………….........

3

Upper support frame

Upper duct cover

Low support frame

Ceiling cover

Low duct cover

Blower box assembly

Filter

Glass


IFB GL-90 ISLAND-90CM



Upper duct cover

Low duct cover

Blower box assembly

IFB -GL- 14T-60CM/90CM

24

Customer Name & signature Date

Customer Response

1.The Installation Person was courteous & helpful Yes No

2.I would describe my experience with Installation as Unacceptable Satisfactory Non satisfactory Very satisfactory

Note: - Installation work is done on chargeable basis & on the customer risk

Scope of Work: - Company will only install the product, fix the pipe and cut the

duct cover. Installation Material like pipe, elbows, clamps & masonry work/woodwork /glass cutting/granite cutting will be carried by customer at his cost & risk . Icertify that the above information and check has been done to my satisfaction & I amfully satisfied with installation of the product.

Check Points-

1.2.

Any major transit damage to the machine observed Yes NoPower point with MCB or other Automatic Yes No

Short Circuit Devicea. Condition of Earthing/ Plug/Power Point( 230V AC 6/16 Amp) Depending on model. b.If poor/faulty or not available ,Customer has been advised to correct the same. Yes No3.User manual 4.Warranty term explained. 5.Basic use demo. 6.Trouble shooting explained 7.Do’s&Don’t explained 8.Procedure to clean/filters/outer body/ Surface/burners/spark plugs/knobs 9.Status of Indicator LED(if applicable) 10.How to use Flame failure device if applicable 11.Status of gas supply tube /pipe/regulator.If not suitable or poor/ cracked/advice the customer to correct the same.

Yes No

Yes NoYes NoYes NoYes NoYes No

Yes NoYes NoYes No

Yes No

Product……………….... Model ……………………….. Serial No ………………….......

Customer Name ………………………………………………………..………..…..............

Address …………………………………………………………………………..….............

Area ………………………………………… City ……………………...…..…..…...........

State………………………………….Pin Code………………………………….............

Telephone No. - Residence………………………..... Mobile………………………........

E-mail………………………………………………………………................................ .

Dealer's Name ………………………………………………………………………....... ..

Invoice No. & Date…………………………………. Price………………………............

Machine Delivered on……………….....…Machine Installed On…………………........

.....................

....................

.....................

......................

........................

.......................

........................

........................

.......................

......................

Installed By ……………………………………Signature……………………….

Receipt/bill no. for Installation Charges ……………………………………................. .

................................................

...... ............................

Installation Report


Low duct cover hook

Low duct cover

Shutter

Filter

Body

IFB - SS 63P-60CM/90 CM IFB -GN-5P-60CM/90CM

4


Low duct cover hook

Low duct cover

Filter

Body

23

The decision of IFB with regards to the settlement of all claims under this warranty shall be final. Any disputes subject to Calcutta court and or / other judicial/ or quasi judicial forums having jurisdiction over the registered office of the Company.

These are the only warrantee terms and conditions given by the company for the respective appliances.

Product Model Warranty period

Hob All models 1 year

Built-in-Oven All models 1 year

Cooking Range All models 1 year

Chimney Lumina ,Dama, Myro, Noir, Miro, Astra Alea

1 year

Chimney

N-3/ Black / SS Olimpia , Arco,multipla,D-2,C-1

GS-60/90T-PL, GL- 14T- 60cm, SS 63 P-60cm, GL- 6 P-60cm GN-5 P-60cm, GL-90 Island, GL-932-

60/90cm

5 year

This appliance is designed for domestic use by individuals at home only.

In case of change of city/ town from the original place of purchase at any given point oftime, then the product would attract a warranty transfercost of Rs . 300/-(The money needsto be paid to the local authorizedservice franchisee).This does not include the cost of re-installation charges . However, if the product is being shifted within the limit of the city then warranty transfer charges will not be applicable.

Outer duct cover

Duct bracket

Inner duct cover

Blower box

Air outlet

Control

Glass Panel

IFB chimney can be installed either in Re-circulation mode or Ducting mode on dependingon the models For efficiency, ensure that gap between the cooking appliances grid and thechimney should be in-between 650mm to 750mm (maximum) ideal is 650mm.The installation must be carried out by qualified & competent person or authorized By IFB withthorough knowledge . The chimney can be ducted to the outside either using flexible orrigid fire retardant ducting pipe of 120 or 150mm or 4 inch or 6 inch (Depends on the models) however choice is left with the installer. Use the rated size for the outlet duct pipe.Smaller size of the duct pipe may reduce the efficiency, may produce more noise & vibration, same will depend on the numbers of bends & length of the duct pipe. However choice is left with Installer. The installer will provide the suitable ducting and sealing material for the installation .For better performance the route of the duct pipe must be kept as short as Possible.

INSTALLATION GUIDE

5

IFB -GL-932-60CM/90CM

22

Company is not liable for any delay in servicing due to the reason that it is beyond thecontrol of the company or any of its authorized service network.

This warranty does not cover defects resulting from the accidents or damage while in transit or to our service center.

This warranty does not cover for consumables in all the product categories for examplebulbs, any kind of filters charcoal & metal, all glass parts, spark plugs, knobs & outer body/ body parts & any type of painting, plating, enameling including rusting etc. or defectsthereof.

In case of no authorized service centre present in the area/ or in case service is to be provided beyond municipal/city limits , then services would be provided from the nearest authorized service area , a fixed charge would be applied (subject to distance are minimumRS.250/-) in additionto the actual to & fro charges along with local conveyance by the shortest route. However, in order to avail the services, the products could also be broughtat the nearest authorized service centre by the customer at their own expenses and risk/damage.

In case warranty period is more than a year after the period of one year , prevailing visiting/repairing charge will be charged as and when the customer calls. However, the spare partswould still be covered under the scheme and would not attract any charges through out the warranty period of the respective product.

The company undertakes no liability in the matter of consequential loss and / or damagescaused to the customer or third party/pet any type of property due to failure / malfunction of the machine. Obligation under this warranty shall be limited to repairing or replacing the defective part.

Any routine maintenance / cleaning / servicing visit would not be covered under this warranty, and would be provided on chargeable basis as per prevailing rates / charges.

Whether defective components are to be replaced / repaired shall be left to the sole discretion of the company. In case of replacement of a part, the defective part removedfrom the product becomes the property of IFB Industries Ltd.

If the Appliance /Components Serial No. Sticker/Plate is removed/ missing/altered /tampered.

Appliances taken out of India.

Damages occurred due to improper electric circuits outside the Appliance & failure due toerratic power supply.

Failure/damage done to the appliance due to operation in an abnormally corrosive Alkaline/ Acidic atmosphere, and or use of harmful chemicals.

If defects/damage arise with optional accessories like Extended Power Supply Cable/Frame etc thereof..Failure/damage due to misuse/negligence/accidents/abuse,action of pests/rodents, fire, flood, earthquake, lightning or any other act of nature/natural calamities & damages traceable to alteration or unauthorized repairs.

Parts replaced or repaired under this warranty are warranted throughout the remaining ofthe original warranty period only.


Step 2:Take out of the chimney from the carton box and remove the filter , then put it on a horizontal work table gently. Fix the reducer tothe airout let if needed . Otherwise fix the exhaust pipe into the air outlet , make sure is connected tightly.

Step 3:Aiming the Low support frame to the holes on the blower box assembly , fix it tightly.Then pull out the exhaust pipe to the level of the low support frame.

Step 4:Insert the upper duct cover into the low duct cover.

65

0-7

50

mm

Air outlet


Upper duct cover

Low duct cover

Low support frame

Screws

Blower box assembly

IFB GL-90 ISLAND-90CM

INSTALLATION

Step 1: Fix the position of the chimney in accordance with the recommend-ed height between 650mmto750mm from the hob and the lower edge of the chimney.

621

Installation / Service / Repairing or use of non-genuine / Modification carried out byperson other than those authorized by IFB.

Failure/damage due to user's negligence towards minor maintenance such as cleaning of Filters/burners/Spark plug or not used in accordance with instructions given in the instructions manual.

If the completed warranty card is not presented to the authorized IFB personnel at the timeof repair.

If the warranty card is not fully and properly filled in and signed at the time of purchase/ installation by the company's authorized dealer/ service engineer. Copy of bill/ invoice ismandatory to avail the warranty.

The warranty becomes null and void in following cases:

Limitations of the Warranty

The warranty period will be 12/24/36/60(Twelve/Twenty-Four/Thirty Six/Sixty) months from the date of invoice for all the above mentioned products respectively. Manufacturingdefects will be rectified free of cost during the said period. However normal applicable repairing cum visiting charge would be applicable after one year. This warranty is subjectto Limitations of Warranty.

IFB Industries Ltd. (“The Company”) warrants to the original domestic purchaser of the above mentioned products (“Appliances”) that it is free from defect in workmanship and materials. During the warranty period as mentioned below the new machine, all the parts of the machine excluding the consumable components listed in the Limitations of Warrantyshall be replaced/ repaired free of charge on intimation to the company/ company authorized service centrenearest to the place where the appliance is installed.

Valid for Chimneys/Built in Hobs/ Cook Tops/ Cooking Ranges/ Built in Ovens

Warranty Terms & Conditions

303mm 285mm

99

3-1

29

3m

m

62

0m

m

595-895mm

460mm

IFB-GL-932-60CM/90CM

20

IFB -GS-60T-PL/90T-PL IFB-GL-6P-60CM/90CM

IFB-SS-63P-60CM/90CM IFB-GN-5P-60CM/90CM

600/900mm

770m

m

IFB-GL-14T-60CM/90CMIFB-GL-90 ISLAND-90CM

5 9 5 - 8 9 5 m m

3 0 0 m m 2 8 3 m m

49

0-8

80

mm

4 7 5 m m

598-595475

51

0-9

10

282

70

303

61

8-1

17

5

595-895600

332

600-892480

40

74

0-1

03

0

212 186

6 0 0 - 8 9 2

70

52

0-9

10

4 8 0

3 0 0 2 8 3

Step6: As per the screw positions on the Upper support frame, drill 4 holes (about φ8 mm) ,then fill the Expanding Rubber into the holes.Aiming the holes on the ceiling cover, fix theceiling cover with the expanding screwstightly and make sure it is firm.

Ceiling

Expanding Rubber

Expanding Screws

Ceiling cover

238

23

8

Step 5:Put the upper and low duct cover on theblower box assembly.Then pull out theexhaust pipe to the level of the upperduct cover.

Blower box assembly

Low duct cover

Upper duct cover

Step 8: Shift the complete chimney ,to make the lowsupport frame cover the upper support frame. Adjust its height. Fix it tightly with 8 pcs M4x10 screws and make sure they are firm.

Upper support frame

ScrewsLow support frame

Step 7: Put upper support frame under the ceiling cover. Use screws to fix the upper support frame to the ceiling frame.

7

19

The chimney has been designed for domestic kitchen use only, never use it for any other purposes or commercial use .Adjust the flame intensity to direct it onto the bottom of the pan only ,making sure that itdoes not engulf the sides. This will not only save(Gas Consumption) energy but its important for your own safety also. If the place where the chimney is installed contains others appliances like central heatingplant/water heating plant, ducting should not be connected to a flue (duct) which is used for exhausting fumes from these appliances. In case chimney is used in conjunction with others appliances use energy other than electric supply, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being thrown back into the room by the chimney. Flue of these appliances must be of the room sealed or balance flue type & ensureadequate supply of air in the room.

IMPORTANT

If you will follow the recommendations/instructions contained in this instruction manual, your appliances will give constant high performance and will remain efficient for many years to come. There could be possible fire hazard if you don't follow the instructions for cleaning/replacing the filters according to these instructions.

IFB declines all responsibility for any damage or injury caused as a result of not following the instructions(in order to avoid a possible risk of fire when the filters are saturated with Oil (grease).

IFB does not guarantee for possible inexactitudes due to printer or transcriptioncontained in this booklet & reserves the right to change any Specifications which is necessary or useful without Prior notice.

When using the gas hob/Cook Top with connection with chimney never leave the burners of the hob/cook top uncovered while the chimney is in use or the pans havebeen removed from the burners (switch off the burners before removing the pans). Special care has to be given while frying, never leave the frying pan unattended as overheated oil may (burst into flames) catch fire.

(DO’S&DON’T)Connect the chimney to the mains using a double pole switch,with proper earthing which corresponds with the rated voltage of the chimney.Incase of doubt please contact authorizedIFB person.

The ducting system of this appliance should not be connected to any other ventilation system which is used for any other appliance of the same type, any other type or for any other purpose. This appliance is not intended for use by persons (including Children) with reduced physical, sensory or mental capabilities or lack of experience & and knowledge, unless they have been given supervision by a person responsible for their safety.Do not leave (unattended) naked flames or flambé cooking under this cooker hood.Children should be supervised to ensure that they do not play with the appliances.

PRECAUTIONS/WARNING

Filter

Fix pin

A

Fix hole

Exhaust pipe

Step 9:

Extend the air outlet of the exhaust pipe out-of

-door. Try to make the bend of the exhaust pipe

is more than 120°.

Step 10:

Pull the upper duct cover to the ceiling, cover

the upper support frame , fix it with 4 pcs M4x

10 screws.

Screws

Upper duct cover

Step 11:

Install filter. Match the fix pin to the fix hole

and push the filter gently as the direction of

arrowA.

Step 1:Take out of the chimney from the carton box and remove the filter,then put it on a horizontal work table gently. Fix the reducerto the air outlet if needed .Otherwise use ST3.9X10 screws to fix theexhaust pipe into the air outlet make sure is connected tightly.

ST3.9X10

screw

Air outlet

IFB -GL- 14T-60CM/90CM&IFB-GL-6P-60CM/90CM&IFB-GL-10PL-60CM/90CM

8

18

To replace led lamp(pic2)Caution: LED lamp can not replace a new bulb, just can replace a new LED Lamp. Make sure all thecontrol switches are off, and the chimney is unplugged! Please follow below instructions:1.Take out the filters, and cut off the wire connection of the lamp.2.Press the spring according to the arrow direction, then you can take off the lamp unit.3.You can replace a new LED lamp unit no more then rating!4. Then put the lamp unit to the chimney in reverse direction. Connect the wire of the lamp.5. Fit on the filters.

pic2To replace normal lamp bulb(Pic.3)Caution :lamp unit may be hot! Wait until it’s cool.Use the same type light bulb!Make sure all the control switches are off, and the chimney is unplugged! Please follow below instructions:Warning: Make sure the bulb is cool before you touch it!1.Take out the filters.2.Loose the old light bulb.3.Replace a new light bulb which is the same type no more then rating!4.Fit on the filters.

Pic.3

CLEANING

LIGHTS

It's recommended to use a damp cloth & mild house hold cleaner or any special Cleaner meant for cleaning the chimney hob & cook top.Never use a wet cloth, sponge or running water.Never use thinner or products containing alcohol as they might damage the paint work.Never use abrasive cleaning materials on painted & stainless steel surface. Take care that the filters don't bend them while washing. Cleaning process must be done after 2 hours of the cooking process.

A

Cassette filters&Metal grease filters need to be cleaned every one month.But this may vary on usage pattern also.In case large amount of oil is used for cooking,same has to be cleaned after very week/fortnight.Filters can be easily clean,just put then in a soap solution of hot water&clean with a brush&then rinse under a running tap water&then wipe with a drycloth.Refix the filters properly.Instructions for removing&for refit push the filter lock backward to release the filter from the slot.

NOTE:Use of optional charcoal filter or ducting mode is left to the installer.However in that case chimney has to be used up to 2nd speed only.

pic1

Ducting Mode

5


Upper duct cover

Step 2:Fix the upper duct cover hook to the upperduct cover with M4 screws.

Step 3:Put the upper duct cover to the low duct cover.Please kindly note that the upperduct cover must fix to the low duct cover’sorientation slot.

Upper duct cover

Low duct cover

Step 4: Matching the holes of low duct cover to theblower box assembly and

fix the low duct cover to the blower box assembly ,as the direction of illustrated.

using 8pcs M4 × 10 screws

Upper duct cover

Low duct cover

Step 5: Fix the position of the chimney in accordance with the recommend-ed heightbetween 650mm to 750 mm from the hoband the lower edge of the chimney.

9

17

SPEEDSLOW SPEED:-Making chappattis/Tea/Re-heating the food/MEDIMUM:-Vegetable cooking/Parantha/Boiling.HIGH:-Deep frying/Pressure cooking/

For maximum efficiency from your chimney use the rear burners of your cook top/hobTurn on the chimney as soon as you start cooking & keep it running for a few minutes afterthe cooking. Regular maintenance & cleaning will enhance the life of the product & will ensure the good performance.

It's advisable to call qualified & authorized Service person for periodically cleaning the internal assembly; same would greatly improve the performance of the product.

Note- if due to any reason if you don't use the chimney, oil/fat may deposed on the filter & surface of the chimney it may start dripping & can cause the fire alsoNote: - before carrying out the maintenance cleaning or replacing the lamp, disconnect thechimney from the main supply (remove the plug from the socket.)

Re-circulation Mode

Check that activated charcoal filters are fitted properly, so that the impurities canbe effectively absorbed.

The chimney has to be operated at the second or lowest speed so that sufficient time is available for the filtration of the air. (Never use high speed) The activated charcoal filters can't be re-used & needs periodical change. The life of the activated charcoal filters are about 3 to 4 months. However if the chimney is used more than 4 hours a day & large amount of oil is used while cooking then filters may require more frequent replacement.*The charcoal filters have to be changed as soon as they are saturated. They can be easily replaced by turning them anti clockwise for removing & clockwise to refit them or by using screw driver to unscrew them for removing them & screwing them to tighten. (Depending on the models)*Applicable for the models which can be installed in the recirculation mode.

NOTE:IN SOFT TOUCH CONTROL,PUSH THE BUTTON AGAIN WILL STOP THE MOTOR .

Hang the entire chimney onto the two expanding screws, ensure the chimney is level and vertical.

Step 7:For IFB-GL-14T-60CM/90CM& IFB-GL-10PL-60CM/90CM& IFB-GL-6P-60CM/90CM

Step 6:For IFB-GL-14T-60CM/90CM& IFB-GL-10PL-60CM/90CM& IFB-GL-6P-60CM/90CMMark 4holes in the wall like this picture .Drill 4 holes of 8mm diameter and 60-70mm in depthin the wall where you marked .Press the 4 expanding tube in to the holes .Tighten the 4 expanding screws of 5x60mm to the expandingtube,make sure it’s fixed enough and cann’t be moved.

Expanding screw

Hood hook

10

4x50Expanding Screw

Expanding Tube

4x50Expanding Screw

Expanding Tube

Step 8: 1. Draw the upper duct cover up to the suitable high, mark on the wall two keyhole of the upper duct cover hook with pen firstly.2. Put down the upper duct cover gently, then drill the keyholes in 50-60mm depth on the horizontal level using 8mm drill.3. Press the expanding tube into the holes.4. Fix the upper duct cover to the wall with with two 4x50 expanding screws.5.Install filter.

Step1:Take out the chimney from the carton boxand remove the filter,then put it on a horizontal work table gently.Fix the reducerto the air outlet if needed.Otherwise use use ST3.9x10 screws to fix the exhaust pipe into the air outlet makesure is connected tightly.

IFB-SS-63P-60CM/90CM&IFB-GN-5P60CM/90CM

Shutter

ST3.9x10Screw


Screw hole

Low duct cover

Screw hole

Low duct cover

Low duct cover hook

M4 Screw

Step 2:Fix the low duct cover hook to the low ductcover with 2pc M4 screws.

Step 3:Put the low duct cover to the body, and use two M4x10 screwsto fix the low duct cover to the body.

11

5

Back of the chimney

A BExpanding Tube

5x60Expanding Screw

Step 5: According the space between the hole A&B ,drill 2 holes in level on the wall with 8mm in diameter and 60-70mm in depth. Press the 2 expanding tube into the holes. Tighten the 2 expanding screws of 5x60mm to the expandingtube.Make sure it is fixed firm and cannot be move.Hang the chimney on the 2 expanding screws ensure the chimney is level and vertical.

Step 4: Put the chimney on the wall and mark the position where you want to install.We recommend the height from the hob to the lower edge of the chimney should be from 650mm-750mm.

16

Accessory shown in the picture(remote) is not a standard part of the product.

A

C

B

C

D

E

Remove control

A: Touch “A” to set the standby mode or power off.

B: Touch “B” to turn on /turn off the cleaning mode.

C: Touch “C” to open or close time delay mode(3min

/6min / 9min).

D: Touch “D” to open or close the LED lamp.

E: Touch “E”, the cooker hood would starting at the

High speed, every time your touch can change the

speed level, form high speed to low speed, total have 6

different speed level. Circulate by this way, If you

touch it for sixth time, the fan function would be

closed.

LAMP

TIME

FAN

POWER

LCD

LIGHT: touch “ ” to open or close the LED lamp.

TIMER: Only when the motor is running, touch “ ”once, to enter in

time delay mode. under time delay mode, keep touch “ ”request

delay, your every touch can add 3 mins (MAX 9mins delay).

Kindly remind : Pls make sure operation in 1min after enter in time

delay mode or the machine will exit the delay status.

FAN: In standby mode, when you touch “ ” ,the cooker hood would

starting at the High speed ,you can touch “ ”to increase the speed or

touch “ ”to reduce the speed, total have 6 different speed level.

POWER: Touch “ ” once then enter in standby mode , you can start

operation. If touch “ ” when the motor is running , then machine

will be Automatic off after 60 seconds. Or you can touch “ ” twice ,

to stop all operations immediately.

12

Inner duct cover

Outer duct cover

Bracket

Inner duct cover

M4 Screw

Exhaust pipe

Reducer for 120mm outlet

Step 3:

Matching the bracket to the holes

of the inner duct cover and fix it

well with M4 screws.

Matching the bracket to the holes

of the Outer duct cover and fix it

well with M4 screws.

Step 2:Take out of the cooker hood from the carton and put it on a horizon-tal work table gently. Fix the reducer pipe into the air outlet of the inner duct, and then fix the exhaust pipe into the top of reducer,make sure is connect the reducer tightly.

Wood Screw5x60

Expanding Tube

Hook

400

Step 1:According to the size of the holes.Drill A.B.C.D.4 holes in level in the wall with 8mm in diameter and 75-85mm in depth.Press the 4 expanding tubeprovided into the holes.Tighten the4 wood screws of 5x60mm whichsupply together with the hood to theexpanding tube,make sure it is fixed enough and can not move.

Step 4:

Insert the inner duct cover into the

outer duct cover.

15

Model: IFB -GS-60T-PL/90T-PL

A B C D E F

This switch is highly-sensitive touch control, use your figure touch the key-press slightly to operate it. And this switch with smoke sensor function.Choice of Auto start & manual start in the manual .

F

A

E

C&D

B

B

A: LampTouch this button one time, the lamp will be lighted, touch again, the lamp will extinguish.B: TimerWhen the cooker hood in standby mode, touch this button 3 seconds ,the cooker hood enter into time setting state and the display screen shows the numbers. Touch + set hour (0-23 circle set) and touch - set minute(0-59 circle set), If in 10 seconds ,you don't have any operation or touch this button again ,then exit time setting state and save the times which you just set.When the cooker hood is working, touch this button one time, then it will be in timing shutdown mode and the display screen shows 03:00,each time touch can increase 1 minute, you can set timer from 0-60 minute. If in 10 seconds ,you don't have any operation, then the cooker hood work in timing shutdown mode, the lamp can turn on/off and the speed can change in this mode. If you touch this button again, then the cooker hood exit this mode. In the last 3 seconds of the time set, the cooker hood will have three DDD sound .In 60 seconds delay mode, touch this button, then will exit 60 seconds delay mode.C&D - In standby mode, touch this two button to adjust the speed you need.E: Speed/Sensor1.Speed function--In standby mode, touch this button one time, the cooker hood will start at high speed, touch this button again, the cooker hood will turn off.2.Sensor--In standby mode, touch this button 3 seconds, then it enter to automatic sensor mode,“AUTO”flash in the display screen, then means that the sensor is working, the motor and the lamps will turn on automatically if the smoke/temperature in kichen near the hood increase rapidly and it would turn off automatically when the smoke/temperature decrease rapidly, touch this button 3 seconds again, then it will exit automatic sensor ,“AUTO”extinguish in the display screen. In automatic sensor mode, the button +/-, , cann't use.F: Power/offWhen the cooker hood in original state, touch this button, it will enter to standby mode, touch this button again, it will turn off the power.When the cooker hood is working, touch this button one time, it will delay 60 seconds. The lamp can turn on/off and the speed can change in this mode.Touch this button again, then it will turn off the cooker hood immediately.When the cooker hood in timing shutdown mode, touch this button one time, it will exit timing shutdown mode and works in 60 seconds delay mode.

When in automatic state, the motor and the lamps will turn on automatically if the smoke in kitchen near the hood increase rapidly.And it would turn off automati cally when the smoke decreased.(PS: When the hood is in automatic state, other buttons of the switch and the remote controlare both could not be operated.)

13

Step 6: 1. Draw the inner duct cover up to the suitable high, mark on the wall two keyhole of the outer duct cover bracket with pen .2. Put down the inner duct cover gently, drill the keyholes in 75-85 mm depth on the horizontal level using 8mm drill.3. Press the expanding tube provided into the holes.4. Matching the inner duct cover with the holes, tighten the inner duct cover with two 5x60 wood screw provided

Step 7:

Extend the air outlet of the exhaust

pipe out-of-door. Try to make the

bend of the exhaust pipe is more

than 120°.

Step 5:

Matching the holes of outer duct

cover and blower box, fix the outer

duct cover to the blower box using

8pcs M4×10 screw provided with

the fixing tool.As the direction of

illustrated.

5x60Wood Screw

Expanding Tube

5x60Wood Screw

Expanding Tube

A B C D E

INSTRUCTIONS FOR USE

LAYOUT FOR THE CHIMNEY CONTROL SWITCH

Model: IFB-GN-5P-60CM & /90CM IFB-GL-6P-60CM/90CM

& IFB-SS-63P-60CM/90CM

A : When the hood is operating,press button A( ),

the hood will be off.

B :Press button B( )，the fan runs at the low speed.

C: Press button C( ), the fan runs at the mid speed.

D :Press button D( ), the fan runs at the high speed.

E: Press button E( ) once,turn on the light.Press it again,turn off the light.

14

A B C D EA :Lamp

Touch this button one time, the lamp will be lighted, touch again, the lamp will extinguish.

B:Timer

When the cooker hood in standby mode, touch this button 3 seconds, the cooker hood enter

into time setting state and the display screen shows the numbers. Touch Lamp button can

set hour(0-23 circle set) and touch Speed button can set minutes(0-59 circle set),if in 10

seconds ,you don’t have any operation or touch this button again, then exit time setting

state and save the time which you set.

When the cooker hood is working, touch this button one time ,then it will be in timing

shutdown mode and the display screen shows 03:00,each time touch can increase 1

minute, you can set the timer from 0-60 minute .If in 10 seconds ,you don’t have any

operation ,then the cooker hood work in timing shutdown mode, the lamp can turn on /off

and the speed can change in this mode. If you touch this button again, then the cooker hood

exit this mode. In the last 3 seconds of the time set ,the cooker hood will have three DDD

sound. In 60 seconds delay mode, touch this button, then will exit 60 seconds delay mode.

C:Display screen

Display time or timing shutdown.

D:Speed/Off

In standby mode, touch this button one time, the cooker hood will start at high speed,

touch this button second time, then will be middle speed, touch this button third time, then

will be low speed, touch this button forth time, then the cooker hood will turn off .

E:Power/Off

When the cooker hood is working, touch this button one time ,it will delay 60 seconds. The

lamp can turn on /off and the speed can change in this mode.

Touch again, then will turn off the cooker hood immediately.

When the cooker hood in timing shutdown mode, touch this button one time ,it will exit

timing shutdown mode and works in 60 seconds delay mode.

Model: IFB-GL-90 ISLAND-90CM & IFB-GL-14T-60CM/90CM

Documents

The user manual - IFB Appliances · Read the manual carefully before using the chimney CALL ONLY IFB AUTHORISED PERSON TO SERVICE YOUR CHIMNEY & USE ONLY GENUINE SPARES IF IN ANY