by ecoTECH design studioThe Sanctuary

I. To provide third party certified homes for chemically sensitive people that have a level of contamination from volatile organic compounds (VOCs) from building materials, finishes and furnishings that are as low as possible. To achieve this we will select materials, finishes and furnishing that have either no VOC or very low VOC emissions.

II. To provide third party certified homes for electrically sensitive people that have as low a level as possible of man-made electromag-netic radiations from internal and external sources. To achieve this we will select electrical equipment with low emissions, specified electrical system installation techniques to reduce or prevent emissions and provide shielding against external communications radiation.

III. Factory certification for each module in accordance with The Healthy Home Standard for Conventional Construction, Modular Addendum (2011)1.

IV. Certification of the assembled and completed house to the Healthy Home Standard for Conventional Construction (2011) from the International Institute for Building Biology and Ecology, Inc.

Methods, Materials and Components

The primary approach for the ecoTEC Living home was to select materials with no or low Volatile Organic Compound (VOC) emissions and to design and build the structure with a continuous barrier to gaseous VOCs emissions located as close as possible to occupied area of the house. Most of the emitting materials are placed outside this envelope. The sole exception to this rule is the wood structural

(studs, plate and header) in the walls. We have selected Douglas Fir as the lowest emitting cost effective structural lumber. All structural lumber exposed to the interior will be seal to slow the movement of natural emissions from the wood.The secondary approach is to use an interior wall material that is capable of soaking up and sequestering formaldehyde for a period of about 70 years. This is designed to take care of the natural formal-dehyde emissions from the wall Douglas Fir structural components. Formaldehyde absorption functions through the latex paint and drywall mud. This feature allows movement of gas from the room into the wall material.Finally, an envelope made from a material that reflects 100% of the outside sourced radio frequency (RF) radiation is installed on all six sides of the structure. The installation method used is designed to reduce to a minimum any gaps or opening in this RF shield. This is the same material that has been installed in the Pentagon to prevent electronic eavesdropping on the RF radiation from internal computer activities.

Materials and Components Inside the VOC Barrier (exposed to the occupied space)

Structural wood: FSC certified Douglas Sealed with three coats of AFM Hardseal. Wall Board: Aldehydes sequestering, no VOCs.Barrier Material: Scrim reinforced aluminum foil. Insulation: Unfaced, formaldehyde-free fiberglass.Windows/ Exterior Doors: Aluminum thermal brokeframes. Plastics are used in gaskets and seals- no flexible PVC, Glass is double

e c o T E C L i v i n g S a n c t u a r y O b j e c t i v e s

ecoTEC Living has created healthy, affordable, factory built and an environmentally sustainable housing solutions for people suffering MCS (Multiple Chemical Sensitivity), and those concerned with living in the healthiest environments. It is the beginning of a “new standard” for healthy housing in the global construction industry that includes single family and multi family housing, as well as commercial applications. The homes address the needs of the MCS community, and individuals with environmental concerns for allergies, air quality issues, and electromagnetic fields (EMF).The team at ecoTEC design studio consists of LEED-certified architects, engineers, technology experts and an advisory board consisting of some of the world’s leading MCS doctors, researchers and environmental toxicologists. In partnership and certified by the international Institute for Bau-Biologie & Ecology (IBE), the housing system is the most transparent in the industry. It is the only housing product available to date that has been scientifically designed, tested, and vetted by environmental toxicologists and building materials experts. The factory built system offers numerous design options and sizes to suit personal preferences. They can be customized to be 100% self-sustaining, with off the grid technology, without compromising on comfort or aesthetics. Trained general contractors are available to help assist with locations, permitting, site work, building and maintenance issues. A customer service help line is available seven days a week. The factory manufactures with non-contaminating construction protocols, eliminating pollution and weather issues. Prior to delivery, each structure is tested for VOCS, energy efficiency, formaldehyde, mold, electromagnetic fields (EMF), communications frequency pollution, as well as radiation. The most advanced air handling system heats and cools by fully exchanging the inside air every two hours at a minimum. The exterior is wrapped in an EMF barrier to protect from unwanted wavelengths. Custom wraps insure moisture contaminates do not enter the units while in transport or during the installation process. The wraps are fully reusable, eliminating any landfill needs. The test units are available for an extended period of time, to insure individual compatibility, with long-term housing solution as the goal. The initial test units will be available in the second half of 2011 on the East Coast, with additional units scheduled reach the rest of the US in 2012.

low-e, RF reflecting.Flooring: NOx absorbing porcelain ceramic tile.Paint: Two coats of AFM SafeCoat zero VOC.Electrical Distribution System: Electric field stopping metal clad cable used throughout. Nylon jacketed, PVC wire insulation to minimize phthalate emissions. Stainless steel receptacle and switch cover plates.Electrical Controls: Bedroom kill switch for electrical devices near the bed. Manual on, occupant sensors to meet energy code with incandescent can lights.Luminaries: Incandescent or LED recessed lighting.Communications Wiring: Telephone and Cat 6e Internet wiring to all major rooms. Optional fiber optic network.HVAC System: Electric, 25 SEER split HVAC system with on demand air purification.Air Heat Exchange System: Two-speed system, MERV 12 particu-late filter & activated coconut charcoal filter, fiberglass. Insulated polyester flex duct with nylon outer wrap.Kitchen: Stainless steel cabinets with stainless counter and sink.Bathroom: All Stainless Sink and Vanity Base, Dual-Flush, Low-Flow Porcelain Toilet, Metal Towel Bar and/ or Towel HooksPlumbing: Supply lines- Choice of stainless steel or copper. Waste lines- choice of cast iron or ABS.Closets: Aluminum shelving and standards.Interior Doors: Solid wood or aluminum and glass as desired.

Materials and Components Outside of the VOC Barrier and Occupied Space

Structural wood: FSC certified Fir and no added urea formalde-hyde plywood. Sealed with 3 coats AFM Hardseal.Roof: synthetic underlayment. Standing seam aluminum or steel roofing.Siding: Membrane seal system allows moister to escape and stops rain penetration with Corten steel and Ipe wood cladding. Air

gapping for additional release.Water Heater: Electric tankless.Main Electric Panel: Chosen for component layout and wired to minimize magnetic field generation.Internet Service: hardwired Internet modem and router.Water Filters: Carbon based whole house filter plus Reverse Osmosis for kitchen drinking and cooking water.Furnishings: Organic cotton, bed linens, blanket, towels. OMI natural latex foam pillows. Back Support Systems Vacuum-extracted bio-foam mattress. Metal frame furniture. shredded natural latex foam padding covered with organic cotton fabric.

Suitability for Intended Use

ecoTec Living recognizes that within the MCS community there is considerable individual variability in the pollutant concentra-tions that causes reactivity and in the specific pollutants that cause reactivity. That being said, we are face with constraints as to what can be designed and factory produced given affordability requirements and manufacturing feasibility. In view of this, we re-alized up front that our product will not satisfy the needs of every person with chemical and electrical sensitivities. It represents the best that can be done at this time in view of the constraints men-tioned. We urge potential customers to arrange to lease our evalu-ation home located near Quakertown PA to evaluate the home’s ability to meet their specific needs and sensitivities.

We work closely with our Clients who have special needs or desire higher EMR electrical filtration systems. Please call the Studio if you have specific requests...310.457.5477

Healthy Home Methods, Materials and Components

7/14/11, Materials-Components Eval Unit v1.3

© 2011 ecoTECH Design Studio, LLC All of the designs, drawings, and images in this booklet are the sole property of ecoTECH design studio LLC. They may not be reproduces in print or electronic media form. They are protected by International copyright law and may not be used without written permission from ecoTECH design studio. Use without permission is strictly prohibited and will be prosecuted to the full extent of the law.

Healthy Home Standard

Integrating Biology & Ecology within the Built Environment

Making Better Choices for Healthy Environments at Home, at Work, at Play

The International Institute for Bau-Biologie® & Ecology, Inc. (IBE)

P.O. Box 16313, Clearwater, Florida, 33766Phone: (866) 960-0333 www.buildingbiology.net

Healthy - Transparent - Sustainable - Affordable...Building a Healthier Planet One Square Foot at a Time