The Formwork Experts. Folding platform K - Doka · PDF fileThe Formwork Experts. Folding platform K User Information Instructions for assembly and use (Method statement) ... Do not

© b

y D

oka

Gm

bH, A

-330

0 A

mst

ette

n

999725002 02/2017en-GB

-

The Formwork Experts.

Folding platform KUser InformationInstructions for assembly and use (Method statement)© by Doka GmbH, A-3300 Amstetten

9725- -0405 4

2 999725002 - 02/2017

User Information Folding platform K

User Information Folding platform K

3999725002 - 02/2017

Contents

4 Introduction4 Elementary safety warnings8 Eurocodes at Doka9 Labelling of platforms (loading data)

10 Doka services

12 System description13 Areas of use14 Utilisation planning15 Main components16 Doka folding platform K in detail17 Formwork planning with Tipos-Doka18 Examples of the system in action

20 Working platform20 Working platform with formwork21 Working platform without formwork

22 Anchoring on the structure22 Overview of suspension methods26 Cone-type suspension points32 Loop-type suspension points

34 Assembly34 Set-up procedure36 Length adjustment38 Outside corners42 Inside corners44 Bridging openings in walls45 Platform assembled from single brackets

48 Repositioning48 Moving the platform

50 Protection platform

54 Other possible areas of use54 Bridging storey-high openings58 Second workdeck level60 Folding platform K as a base on which to

stand the Working scaffold Modul61 Climbing with the Folding platform K

62 General remarks62 Sideguards on exposed platform-ends63 Fall-arrest systems on the structure64 Transporting, stacking and storing

69 Component overview

4 999725002 - 02/2017

Introduction User Information Folding platform K

IntroductionElementary safety warnings

User target groups

▪ This booklet is aimed at all persons who will be work-ing with the Doka product or system that it describes. It contains information on the standard design for setting up this system, and on correct, compliant uti-lisation of the system.

▪ All persons working with the product described herein must be familiar with the contents of this booklet and with all the safety instructions it contains.

▪ Persons who are incapable of reading and under-standing this booklet, or who can do so only with dif-ficulty, must be instructed and trained by the cus-tomer.

▪ The customer is to ensure that the information mate-rials provided by Doka (e.g. User Information book-lets, Instructions for Assembly and Use, Operating Instruction manuals, plans etc.) are up to date and available to all users, and that they have been made aware of them and have easy access to them at the usage location.

▪ In the relevant technical documentation and form-work utilisation plans, Doka shows the workplace safety precautions that are necessary in order to use the Doka products safely in the usage situations shown. In all cases, users are obliged to ensure compliance with national laws, standards and regulations throughout the entire project and to take appropriate additional or alternative workplace safety precau-tions where necessary.

Hazard assessment

▪ The customer is responsible for drawing up, docu-menting, implementing and continually updating a hazard assessment at every job-site. This booklet serves as the basis for the site-specific hazard assessment, and for the instructions given to users on how to prepare and utilise the system. It does not substitute for these, however.

Remarks on this booklet

▪ This booklet can also be used as a generic method statement or incorporated with a site-specific method statement.

▪ Many of the illustrations in this booklet show the situation during formwork assembly and are therefore not always complete from the safety point of view.Any safety accessories not shown in these illustra-tions must still be used by the customer, in accord-ance with the applicable rules and regulations.

▪ Further safety instructions, especially warnings, will be found in the individual sections of this booklet!

Planning

▪ Provide safe workplaces for those using the form-work (e.g. for when it is being erected/dismantled, modified or repositioned etc). It must be possible to get to and from these workplaces via safe access routes!

▪ If you are considering any deviation from the details and instructions given in this booklet, or any application which goes beyond those described in the booklet, then revised static cal-culations must be produced for checking, as well as supplementary assembly instructions.

Regulations; industrial safety

▪ All laws, Standards, industrial safety regulations and other safety rules applying to the utilisation of our products in the country and/or region in which you are operating must be observed at all times.

▪ If a person or object falls against, or into, the side-guard component and/or any of its accessories, the component affected may only continue in use after it has been inspected and passed by an expert.

User Information Folding platform K Introduction

5999725002 - 02/2017

Rules applying during all phases of the assignment

▪ The customer must ensure that this product is erected and dismantled, reset and generally used for its intended purpose in accordance with the applica-ble laws, standards and rules, under the direction and supervision of suitably skilled persons. These persons' mental and physical capacity must not in any way be impaired by alcohol, medicines or drugs.

▪ Doka products are technical working appliances which are intended for industrial / commercial use only, always in accordance with the respective Doka User Information booklets or other technical docu-mentation authored by Doka.

▪ The stability of all components and units must be ensured during all phases of the construction work!

▪ The functional / technical instructions, safety warn-ings and loading data must all be strictly observed and complied with. Failure to do so can cause acci-dents and severe (even life-threatening) damage to health, as well as very great material damage.

▪ Fire-sources are not permitted anywhere near the formwork. Heating appliances are only allowed if properly and expertly used, and set up a safe dis-tance away from the formwork.

▪ The work must take account of the weather condi-tions (e.g. risk of slippage). In extreme weather, steps must be taken in good time to safeguard the equipment, and the immediate vicinity of the equip-ment, and to protect employees.

▪ All connections must be checked at regular intervals to ensure that they are secure and in full working order. In particular threaded connections and wedged con-nections have to be checked and retightened as nec-essary in accordance with activity on the jobsite and especially after out-of-the-ordinary occurrences (e.g. after a storm).

▪ It is strictly forbidden to weld Doka products – in par-ticular anchoring/tying components, suspension components, connector components and castings etc. – or otherwise subject them to heating. Welding causes serious change in the microstruc-ture of the materials from which these components are made. This leads to a dramatic drop in the failure load, representing a very great risk to safety.The only articles which are allowed to be welded are those for which the Doka literature expressly points out that welding is permitted.

Assembly

▪ The equipment/system must be inspected by the customer before use, to ensure that it is in suitable condition. Steps must be taken to rule out the use of any components that are damaged, deformed, or weakened due to wear, corrosion or rot.

▪ Combining our formwork systems with those of other manufacturers could be dangerous, risking damage to both health and property. If you intend to combine different systems, please contact Doka for advice first.

▪ The equipment/system must be assembled and erected in accordance with the applicable laws, Standards and rules by suitably skilled personnel of the customer's, having regard to any and all required safety inspections.

▪ It is not permitted to modify Doka products; any such modifications constitute a safety risk.

Closing the formwork

▪ Doka products and systems must be set up so that all loads acting upon them are safely transferred!

Pouring

▪ Do not exceed the permitted fresh-concrete pres-sures. Over-high pouring rates overload the form-work, cause greater deflection and risk breakage.

Stripping out the formwork

▪ Do not strip out the formwork until the concrete has reached sufficient strength and the person in charge has given the order for the formwork to be stripped out!

▪ When stripping out the formwork, never use the crane to break concrete cohesion. Use suitable tools such as timber wedges, special pry-bars or system features such as Framax stripping corners.

▪ When stripping out the formwork, do not endanger the stability of any part of the structure, or of any scaffolding, platforms or formwork that is still in place!

6 999725002 - 02/2017


Transporting, stacking and storing

▪ Observe all regulations applying to the handling of formwork and scaffolding. In addition, the Doka slinging means must be used - this is a mandatory requirement.

▪ Remove any loose parts or fix them in place so that they cannot be dislodged or fall free!

▪ All components must be stored safely, following all the special Doka instructions given in the relevant sections of this booklet!

Maintenance

▪ Only original Doka components may be used as spare parts. Repairs may only be carried out by the manufacturer or authorised facilities.

Miscellaneous

The weights as stated are averages for new material; actual weights can differ, depending on material toler-ances. Dirt accretions, moisture saturation, etc. can also affect weight.We reserve the right to make alterations in the interests of technical progress.

Symbols used

The following symbols are used in this booklet:

Important noteFailure to observe this may lead to malfunc-tion or damage.

CAUTION / WARNING / DANGERFailure to observe this may lead to material damage, and to injury to health which may range up to the severe or even life-threaten-ing.

InstructionThis symbol indicates that actions need to be taken by the user.

Sight-checkIndicates that you need to do a sight-check to make sure that necessary actions have been carried out.

TipPoints out useful practical tips.

ReferenceRefers to other documents and materials.

☞


7999725002 - 02/2017

8 999725002 - 02/2017


Eurocodes at Doka

In Europe, a uniform series of Standards known as Eurocodes (EC) was developed for the construction field by the end of 2007. These are intended to provide a uniform basis, valid throughout Europe, for product specifications, tenders and mathematical verification.The EC are the world's most highly developed Stand-ards in the construction field.In the Doka Group, the EC are to be used as standard from the end of 2008. They will thus supersede the DIN norms as the "Doka standard" for product design.

The widely used "Permissible stress design" (compar-ing the actual stresses with the permissible stresses) has been superseded by a new safety concept in the EC.The EC contrast the actions (loads) with the resistance (capacity). The previous safety factor in the permissible stresses is now divided into several partial factors. The safety level remains the same!

Comparison of the safety concepts (example)

Ed Design value of effect of actions (E ... effect; d ... design) Internal forces from action Fd (VEd, NEd, MEd)

Rd Design value of the resistance (R ... resistance; d ... design) Design capacity of cross-section (VRd, NRd, MRd)

Fd Design value of an action Steel: Rd =Rk Timber: Rd = kmod ·

Rk

Fd = F · Fk M M

(F ... force)Fk Characteristic value of an action

"actual load", service load (k ... characteristic) e.g. dead weight, live load, concrete pressure, wind

Rk Characteristic value of the resistance e.g. moment resistance to yield stress

F Partial factor for actions (in terms of load; F ... force) e.g. for dead weight, live load, concrete pres-sure, wind Values from EN 12812

M Partial factor for a material property (in terms of material; M...material) e.g. for steel or timber Values from EN 12812

kmod Modification factor (only for timber – to take account of the moisture and the duration of load action) e.g. for Doka beam H20 Values as given in EN 1995-1-1 and EN 13377

Ed

Rd

Permissible stress design EC/DIN concept

Factual Fpermissible Ed Rd

A Utilisation factor

60 [kN]

60<70 [kN]

115.5 [kN]

� ~ 1.65

Fyield

Fpermissible

Factual

9801

3-10

0

A

90 [kN]

115.5 [kN]

90<105 [kN]

Rk

Rd

Ed

�M

= 1.1

�F

= 1.5

9801

3-10

2

A

The "permissible values" communicated in Doka documents (e.g.: Qpermissible = 70 kN) do not correspond to the design values (e.g.: VRd = 105 kN)!➤ Avoid any confusion between the two!➤ Our documents will continue to state the per-

missible values. Allowance has been made for the following par-tial factors: F = 1.5 M, timber = 1.3 M, steel = 1.1 kmod = 0.9In this way, all the design values needed in an EC design calculation can be ascertained from the permissible values.


9999725002 - 02/2017

Labelling of platforms (loading data)

National regulations may require platforms to be labelled with their loading data. The form below can be used as a master copy, making it easier to label each platform.

Before the loading-data labelling is affixed, technically qualified personnel from the company responsible for erecting the system must verify that it has been prop-erly assembled and erected in accordance with the applicable laws, standards and regulations.

Construction firm / site

Note on max. loading for Doka folding platform K

Conforms to the following EN 12811 Load Class (tick relevant box)

Permitted service load:

Dead weight of the unit (platform) to be lifted and repositioned:

Please refer to the User Information booklet or planning documents for detailed usage instructions

Date Name

2 3 4 5 6

9725

-106

10 999725002 - 02/2017


Doka services

Support in every stage of the project

Doka offers a broad spectrum of services, all with a sin-gle aim: to help you succeed on the site.Every project is unique. Nevertheless, there is one thing that all construction projects have in common – and that is a basic structure with five stages. We at Doka know our clients' varying requirements. With our consulting, planning and other services, we help you achieve effective implementation of your formwork assignment using our formwork products – in every one of these stages.

Project Development Stage Bidding Stage Operations Scheduling Stage

Taking well-founded decisions thanks to professional advice and consulting

Optimising the preliminary work with Doka as an experienced part-ner

Controlled, regular forming oper-ations, for greater efficiency resulting from realistically calculated formwork concepts

Find precisely the right formwork solutions, with the aid of ▪ help with the bid invitation ▪ in-depth analysis of the initial sit-

uation ▪ objective evaluation of the plan-

ning, execution, and time-risks

Draw up potentially winning bids, by ▪ basing them on realistically calcu-

lated guideline prices ▪ making the right formwork

choices ▪ having an optimum time-calcula-

tion basis

Plan cost-effectively right from the outset, thanks to ▪ detailed offers ▪ determination of the commission-

ing quantities ▪ co-ordination of lead-times and

handover deadlines

1 2 3


11999725002 - 02/2017

The advantages for you thanks to professional advice and consulting

▪ Cost savings and time gains When we advise and support you right from the word "go", we can make sure that the right formwork systems are chosen and then used as planned. This lets you achieve optimum utilisation of the formwork equipment, and effec-tive forming operations because your workflows will be correct.

▪ Maximised workplace safety The advice and support we can give you in how to use the equip-ment correctly, and as planned, leads to greater safety on the job.

▪ Transparency Because our services and costs are completely transparent, there is no need for improvisation dur-ing the project – and no unpleas-ant surprises at the end of it.

▪ Reduced close-out costs Our professional advice on the selection, quality and correct use of the equipment helps you avoid damage, and minimise wear-and-tear.

Concrete Construction Stage Project Close-out Stage

Optimum resource utilisation with assistance from the Doka Formwork Experts

Seeing things through to a posi-tive conclusion with professional support

Workflow optimisation, thanks to ▪ thorough utilisation planning ▪ internationally experienced pro-

ject technicians ▪ appropriate transport logistics ▪ on-site support

Doka Services are a byword for transparency and efficiency here, offering ▪ jointly handled return of rented

formwork ▪ professional dismantling ▪ efficient cleaning and recondition-

ing using special equipment

4 5

12 999725002 - 02/2017

System description User Information Folding platform K

System description

The comprehensive range of ready-to-use platforms for every field

The Doka folding platforms K are pre-assembled (and thus immediately work-ready) scaffold platforms.They are delivered to the site folded closed, to save space.At the site, it takes only an instant to unfold them before they are craned to the prepared suspension points and hung into place.A range of practical accessories makes work on the site a lot easier and does away with the need for costly job-site improvisations.

Among the many advantages of the Doka folding platform K:

▪ High load-bearing capacity of up to 6 kN/m2 (600 kg/m2) - Load Class 6

▪ The 3.00 or 4.50 m long platforms are easy to plan ▪ Safe corner transition with the Folding platform K

outside corner and the Folding platform K inside cor-ner

▪ Closure platform 3.00m for length adjustment and corner solutions – all-in-one, with integral railings

▪ Retractable crane-hoisting points for an even, safe platform deck – no projecting parts that anybody might trip over

▪ Long service life thanks to its sturdy design, var-nished floor planking and galvanised steel construc-tion

▪ Deck-boards are protected by a steel profile at either end of the platform

▪ Climbing formwork K – simply adding a few standard Doka components to the platforms transforms them into a fully-fledged tiltable climbing formwork system

▪ Support lengthening piece and suspended platform – as system components for bridging storey-high openings and for safe finishing-work

▪ Good bridging of wall and window openings ▪ Handrail extension K and safety netting – for extend-

ing and reinforcing the rooftop fall barrier function ▪ Side handrail clamping unit T – the quick way of put-

ting up safe end-railings at the ends of the platforms ▪ Two different suspension methods, for better adap-

tation to the on-site situation:- cone-type mounting- loop-type suspension points

▪ Very little space required for storage and transport

9715-800

User Information Folding platform K System description

13999725002 - 02/2017

Areas of use

The comprehensive ready-to-use platform-range of the Folding platform K series meets the following require-ments: ▪ EN 12811-1 and ČSN 738101 compliant working

platforms

▪ DIN 4420-1, ÖNORM B4007 and ČSN 738106 com-pliant protection platforms

▪ Construction Worker Protection Ordinance (BauV)

Practical examples of Load Classes

Overview of possible areas of use

Load Class2

Load Class3

Load Class4, 5, 6

For service and maintenance work, especially for cleaning operations on facades

e.g. for external rendering and stucco work, coating, pointing or repair work; as a reinforce-ment or pouring platform in reinforced-concrete

construction work.

Normally for masonry and external rendering work, tiling and squared-stone facing work, and

heavy site-erection work.

Only for work in which it is not necessary to store building materials or parts on the platform

decking.

The materials and equipment stored on the platform decking may not be set down on the

platform by lifting appliances.

Building materials and parts may be set down on the platform by lifting appliances and stored

on the platform decking.Precondition:

When materials are stored on the platform decking, a clear access passage at least 0.20 m

wide must be left free.

Precondition:When materials are stored on the platform

decking, a clear access passage at least 0.20 m wide must be left free.

Permitted service load: 1.5 kN/m2 (150 kg/m2) Permitted service load: 2.0 kN/m2 (200 kg/m2)

Load ClassPermitted service load

43.0 kN/m2

(300 kg/m2)

54.5 kN/m2

(450 kg/m2)

66.0 kN/m2 (600

kg/m2)or partial-area load

The actual load is made up of the weight of the stored material and of the persons on the plat-

form. For each person, a weight of 100 kg must be

assumed.

The actual load is made up of the weight of the stored material and of the persons on the plat-

form. For each person, a weight of 100 kg must be

assumed.

Working platformwith formwork without formwork

9725-353-01 9725-354-01

Protection platformFall-stop scaffold Sloping-rooftop fall barrier Protective canopy

9725

-3

-050

2

9725

-3

-070

2

9725

-355

-01

☞ For detailed information on the different areas of use, see the section 'Working platform' or 'Protection platform'!

14 999725002 - 02/2017


Utilisation planning

with the Folding platform K product range

The suspension points of the Folding platforms K 3.00m and 4.50m always have the same grid spacing of 150 cm (distance from edge 75 cm). This greatly facilitates planning and site erection.Exception: On the Folding platform K inside corner, the distance from the edge is 80 cm.

Note:The narrowside of the Folding platform K inside corner where the rear railing is open must be facing the wall.

* ... The actual closure length is 5 cm more than the stated system dimension.1) ... Dimension when using cone-type suspension points 2) ... Dimension when using the Bow head K-ES 3) ... Fixed dimension in corner zone (Folding platform K inside corner) 4) ... Centre-to-centre spacing of suspension points 5) ... Nominal dimensions of platforms

A Doka folding platform K 3.00mB Doka folding platform K 4.50mC Doka folding platform K outside cornerD Doka folding platform K inside cornerE Closure platform 3.00m

250*

803)

803)

7575

247247

803)

401)

362)

401) 22,5

22,5

362)10

0100

100

401)

401)

2641)

362)

362)

2682)

1504)

1504)

2641)

2682)

1504)

4505) 3005)

247

1504)

1504)1504)

1504)

1504)

1504)

1504)

75

75

75

75

1504)

7575

7575

75

A

A

A

A

CAEBC

C

C

D

D

D

A

A

E

A

E

A

A

C B

B

9725-438-01

72.5

72.5

72.5

72.5

72.5

72.5

1504)

1504)

1504)

1504)

803)

295

295

445

184

A

C

B

D

9725

-438

-04

9725

-438

-05

9725

-438

-06


15999725002 - 02/2017

Main components

Doka folding platform K

▪ 2 possible lengths of platform, as required by the sit-uation:

- 3.00 m (2 brackets)- 4.50 m (3 brackets)

▪ The suspension points always have the same grid spacing of 1.50 m

Length adjustment

Closure platform 3.00m for length adjustment and cor-ner solutions – all-in-one, with integral railings

Corner solutions

Safe corner transition with the Folding platform K out-side corner and the Folding platform K inside corner

Doka folding platform K outside corner

Doka folding platform K inside corner

9725-430-01

9725-501-01

9725-429-01

9725-428-01

16 999725002 - 02/2017


Doka folding platform K in detail

System dimensions:

a ... 2120 mm b ... 1840 mm c ... 50 mm d ... 1080 mm e ... 530 mm f ... 1210 mm g ... 2450 mm

Cone and loop-type suspension points possible

To make the Folding platform K ready for loop-type sus-pension points, simply retrofit the platform with the Bow head K-ES.

Crane hoisting points

▪ No projecting parts: The retractable crane hoisting points leave an even, safe work-deck.

Attaching panel struts

▪ Connection sockets for attaching the panel struts are integrated in the platform.

A Bow head K-ES

9725-428-02

a

b

e

f

g

dc

9725-217-01A

Front crane hoisting point Rear crane hoisting point

A Doka folding platform KB Connection socketC Panel strutD Star screw

9725-218-01 9725-219-01

9725-406-01

B

D

A

C


17999725002 - 02/2017

Formwork planning with Tipos-Doka

Tipos-Doka helps you to form even more efficiently

Tipos-Doka has been developed to assist you in planning the use of your Doka formwork. For wall formwork, floor formwork and platforms, it puts the same tools into your hands that we at Doka use ourselves for formwork planning.

Easy to use, fast and accurate results

The easy-to-use interface makes for very fast working. From when you input your layout (with the 'Schal-Igel'® on-screen assistant), all the way through to when you manually put the finishing touches to the formwork solution the program gives you. All this saves time - yours.The program contains a large number of templates and wizards, so you can be sure of always getting the opti-mum technical and economical solution to your form-work task. This makes for greater operational reliability, and cuts costs.You can get to work right away with the piece-lists, plans, views, sections and perspective drawings that the program gives you. Operational reliability is also enhanced by the high level of detail of the plans.Among other things, Tipos-Doka plans the following with Folding platforms: ▪ Distribution of the folding platforms in accordance

with the Load Classes ▪ Closures ▪ Corner solutions ▪ Safety barriers

Drawings of formwork and platforms really can be this detailed! Both for the layout and for spatial representations, Tipos-Doka sets an impressive new standard of visual presentation.

Always the right quantities of formwork and accessories

You can import the automatically generated piece-lists into many other programs for further processing.Formwork components and accessories that have to be organised at short notice, or replaced by improvisation, are the ones that cost the most. This is why Tipos-Doka offers complete piece-lists that leave no room for improvisation. Planning with Tipos-Doka eliminates costs before they have a chance to even arise. And your depot can make the best possible use of its stocks.

18 999725002 - 02/2017


Examples of the system in action


19999725002 - 02/2017

20 999725002 - 02/2017

Working platform User Information Folding platform K

Working platformWorking platform with formwork

H (horizontal load) and V (vertical load) refer to the loads at the suspension point. These loads cover all the usage situations given here. The structure, and all parts of the structure, must be verified for stability on the basis of this data.

* Ensure that the Folding platform K is at the correct height relative to the top of the floor slab. See the section headed 'Loop-type suspension points'

Note:The values stated above for the permitted service load and closures must also be complied with when using inside corners and outside corners.

Formwork shored from folding platform Formwork shored from floor slab

Load Class 2 (Permitted service load: 1.5 kN/m2 (150 kg/m2) on folding platform and pouring platform).Max. width of pouring platforms 1.20 m.

Type of suspension point Suspension cone Suspension loop ES* Suspension cone Suspension loop ES*

H = 14.0 kNV = 24.0 kN

H = 14.0 kNV = 18.0 kN

H = 14.0 kNV = 24.0 kN

H = 14.0 kNV = 18.0 kN

Closures 1.00 m 0.75 m 1.00 m 0.75 mSuspended platform Allowed Not allowed Allowed Not allowedFolding platform K inside corner Allowed Not allowed Allowed Not allowed

Formwork height 3.00 m 3.00 m 5.50 m 4.00 mWind speeds up to 55 km/h (as per "UVV" accident preven-tion rule for cranes). At wind speeds of up to 45 km/h, a form-work height of 4.00 m is possible.If higher wind speeds are likely, and when work finishes for the day or before prolonged work-breaks, the formwork must be closed. Fix the panel struts of the opposing formwork to the floor-slab stably.

A Star screwB Opposing formwork

AB

9725

-463

-01

B

9725

-464

-01

CAUTIONThe panel struts on the folding platform must:➤ only be positioned in the axis of the bracket➤ only be fitted into the special connection

sockets, and➤ only be fixed with star screws.

Tie rod 15.0mm is forbidden!

User Information Folding platform K Working platform

21999725002 - 02/2017

Working platform without formwork

Doka folding platform K 3.00m and 4.50m

H (horizontal load) and V (vertical load) refer to the loads at the suspension point. These loads cover all the usage situations given here. The structure, and all parts of the structure, must be verified for stability on the basis of this data.

1) See also 'Overview of suspension methods'. 2) For closures of longer than 1.00 m, only use the Closure platform 3.00m.


2) For closures of longer than 1.00 m, only use the Closure platform 3.00m.


2) For closures of longer than 1.00 m, only use the Closure platform 3.00m. 3) Closures of up to 2.50 m long are permitted if the closure platform is resting on a Folding platform K outside corner on both sides (e.g. pier).

Type

s of

sus

pens

ion

poin

t 1) Suspension cone

Rock anchor spreader unit 15.0 + Suspension cone 15.0 with collarSuspension cone 15.0 f. insulation up to 11cm (insulation thickness up to 6cm)Suspension cone 15.0 f. insulation up to 11cm (insulation thickness up to 11 cm)Suspension loop ESBridge edge beam anchor 15.0Suspension profile AK/ES

Suspension plate AK/ES

H = 9.2 kNV = 9.2 kN

H = 16.2 kNV = 16.0 kN

H = 25.0 kNV = 26.0 kN

Load Class 2Permitted service load

1.5 kN/m2

(150 kg/m2)


2.0 kN/m2

(200 kg/m2)


3.0 kN/m2

(300 kg/m2)

Load Class 5Permitted service

load4.5 kN/m2

(450 kg/m2)


6.0 kN/m2

(600 kg/m2)

Closures 1.00 m 2.50 m 2) 1.50 m 2) 1.00 m 0.75 m 0.50 m


1.5 kN/m2

(150 kg/m2)


2.0 kN/m2

(200 kg/m2)


3.0 kN/m2

(300 kg/m2)

Load Class 5Permitted service

load4.5 kN/m2

(450 kg/m2)


6.0 kN/m2

(600 kg/m2)

Closures 1.00 m 2.50 m 2) 1.50 m 2) Not allowed Not allowed Not allowed


1.5 kN/m2

(150 kg/m2)


2.0 kN/m2

(200 kg/m2)


3.0 kN/m2

(300 kg/m2)Closures 2.50 m 2) 1.50 m 2) 3) Not allowed

22 999725002 - 02/2017

Anchoring on the structure User Information Folding platform K

Anchoring on the structureOverview of suspension methods

Cone-type suspension points

Suspension point in concrete

Without insulation (standard suspension point)

Without insulation (variant using Bridge edge beam anchor)

With insulation of up to 11 cm

Suspension point fixed in a hole subsequently drilled in the concrete

9725-216-01

Expendable parts Re-useable parts

Pigtail anchor 15.0 Sealing sleeve 15.0/5cm

Cantilever posi-tioning cone

15.0/5cm

Tie rod 15.0, length approx. 20 cm Super plate 15.0 Suspension cone

15.0/5cm

or or or

Stop anchor 15.0 Sealing sleeve S 15.0 5cm Fixing plate 15.0

Expendable parts Re-useable partsBridge edge beam anchor 15.0 Nailing cone 15.0 Screw-in cone 15.0


Pigtail anchor 15.0 Sealing sleeve 15.0 f. insulation up to 11cm

Suspension cone 15.0 f. insulation up to 11cm Cone screw Rd28

or In addition, where needed:Stop anchor 15.0 Positioning disk Rd28


Rock anchor spreader unit 15.0 Tie rod 15.0 Rock anchor installation tube Suspension cone 15.0 with collar

User Information Folding platform K Anchoring on the structure

23999725002 - 02/2017

Suspension points subsequently fixed onto the concrete floor-slab

Without insulation, or with insulation up to 10 cm thick

With insulation and/or facing brickwork between 10 and 30 cm thick

Suspension point for fair-faced concrete

The Fair-faced concrete positioning cone 15.0 5cm is particularly suitable for fair-faced concrete projects where the form-tie points and suspension points are required to make a uniform hole-pattern.

Anchoring situation

Illustrated inside the concrete

a ... 26 cm (where there is 5 cm concrete cover on both sides)

If it is intended to use this type of suspension point, a Doka technician must be contacted before the project starts.

Result (in terms of appearance):

The form-tie points and/or suspension points have a uniform, regular hole-pattern.

Re-useable partSuspension plate AK

Re-useable partSuspension profile AK

☞ Safety warning: The Fair-faced concrete positioning cone may only be used on suspension points that are located within a maximum of 80 cm from the top edge of the concrete. The reason for this restriction is the reduced load-bearing capacity of such suspension points, due to the shallower screw-in depth of the end of the tie rod nearest the form-ply.

A Fair-faced concrete positioning cone 15.0 5cmB Stop anchor double-ended 15.0C Fair-faced concrete plug 41mm

B A

9725-500-01

B C

9725-500-01

a

Tr63

5-20

1-01

24 999725002 - 02/2017


Loop-type suspension points

In order to hang the Folding platform K into place, there must be a Bow head K-ES mounted on every Suspen-sion head.1) Insert the Bow head K-ES into the Suspension

head of the Folding platform K2) Push the Safety pin ES into place

3) Secure by turning the lever-latch

Suspension point in concrete floor-slab

Without insulation (standard suspension point)




1

2

9725

-333

-01

Expendable partSuspension loop ES

2 per suspension point

Re-useable partSuspension plate ES


Re-useable partSuspension profile ES



25999725002 - 02/2017

26 999725002 - 02/2017


Cone-type suspension points

Suspension situation with cone-type suspension points:

a ... Cone axis to top of decking: 6.5 cm

Dimensioning the suspension point

Suspension point in concrete – without insulation (standard suspension point)

Tools needed: ▪ Reversible ratchet 1/2" ▪ Positioning-cone spanner 15.0 DK

Positioning point (with hole drilled through form-ply)

➤ Drill a diam. 18 mm hole in the form-ply (position as shown in shop drawing / assembly plan).

➤ Screw the stop anchor or pigtail anchor into the Can-tilever positioning cone until fully engaged.

➤ Insert a Tie rod 15.0 (length approx. 20 cm) through the hole drilled in the form-ply, screw it into the Can-tilever positioning cone and tighten it with the Super plate 15.0.

a ... 1 cm

➤ Warning against not screwing in the parts (e.g. stop anchors or pigtail anchors) far enough into the positioning cones: This may subsequently lead to reduced load-bearing capacity and to the failure of the suspension point - resulting in injury and damage.

➤ Always screw in components until they fully engage – that is, for the full length as far as the depth mark on the stop anchor or pigtail anchor.

➤ Make sure that the parts then used for the suspension point are for the same depth of concrete cover.

➤ Do not use the positioning cone as a rod connector

➤ Tie the pigtail anchor or stop anchor to the reinforcement with binding wire. This pre-vents it becoming detached during pouring and vibrating.

WARNINGSensitive anchoring, suspension and connec-tor components!➤ Never weld or heat these components.➤ Any components that are damaged or have

been weakened by corrosion or wear must be withdrawn from use.

☞ Cones and accessories are also available for a 2 cm depth of concrete cover. The articles in question are: ▪ Suspension cone 15.0 Art.n° 581970000 ▪ Cantilever positioning cone 15.0 Art.n°

581698000 ▪ Sealing sleeve 15.0 Art.n° 581989000 ▪ Sealing sleeve S 15.0 Art.n° 581696000These suspension points are prepared in a sim-ilar way to the instructions given for the Sus-pension cone 15.0/5cm. However, special care must be taken to ensure that components for different depths of concrete cover are kept strictly separate (see warnings above)!

a

9725

-249

-01

The required cube compressive strength of the con-crete at the time of loading must be specified sepa-rately for each project by the structural designer. It will depend on the following factors: ▪ load actually occurring ▪ length of stop anchor or pigtail anchor ▪ reinforcement / extra reinforcement steel ▪ distance from edgeThe introduction of the forces, the transfer of these forces into the structure, and the stability of the overall construction, must all be verified by the structural designer.The required cube compressive strength fck,cube,current must be at least 10 N/mm2, however.

A Stop anchor 15.0 or Pigtail anchor 15.0C Cantilever positioning cone 15.0 5cmD Sealing sleeve S 15.0 5cmE Depth markF Tie rod 15.0mmG Super plate 15.0H Longitudinal reinforcement and U-reinforcements, min. diam.

8 mm, spaced max. 15 cm apart

9725-398-01

E

a

GH


27999725002 - 02/2017

Note:Cantilever positioning cones 15.0 5cm are supplied together with Sealing sleeves S 15.0 5cm. Every time the cones are re-used, fit them with new sealing sleeves first.

Positioning point (with no hole drilled through form-ply)

e.g. where there is a Doka beam or the profile of a framed formwork panel directly behind the location of the positioning point.➤ Nail a Cantilever positioning cone to the form-ply

using a Fixing plate 15.0 (position as shown in pro-ject plan).

➤ Screw the stop anchor or pigtail anchor into the Can-tilever positioning cone until fully engaged.

a ... 1 cm

Note:Cantilever positioning cones 15.0 5cm are supplied together with Sealing sleeves S 15.0 5cm. Every time the cones are re-used, fit them with new sealing sleeves first.

Before pouring

➤ Check all positioning points and suspension points once again.

Suspension point

➤ Use a Reversible ratchet 1/2" and Positioning-cone spanner 15.0 DK to unscrew the Cantilever position-ing cone together with the Fixing plate 15.0.When carefully fitted, and removed without using force, the Fixing plate 15.0 can be used several times over.

➤ Screw in Suspension cone 15.0 until fully engaged, and tighten using Reversible ratchet 1/2".

Pigtail anchor 15.0

d ... min. 16.0 cm a ... 74.0 cm (where there is 5 cm concrete cover on both sides)

Anchoring in the wall

Stop anchor 15.0 16cm 55

a ... 26 cm (where there is 5 cm concrete cover on both sides)b ... min. 20 cm

1 cm distance between depth mark and cone.

A Stop anchor 15.0 or Pigtail anchor 15.0C Cantilever positioning cone 15.0 5cmD Sealing sleeve S 15.0 5cmE Depth markF Fixing plate 15.0G Longitudinal reinforcement and U-reinforcements, min. diam.


1 cm distance between depth mark and cone.

When the Fixing plate 15.0 is used, we also rec-ommend using the Sealing sleeve S 15.0 5cm.This has a trumpet-shaped end which improves the tightness of the join.

9725-410-01

E

F

a

G

➤ Warning against not screwing in the sus-pension cones sufficiently far: The resulting reduction in the load-bearing capacity may cause the suspension point to fail, leading to injury and damage.

➤ Never mix components that have different depths of concrete cover - this causes the screw-in depths to be insufficiently deep.

➤ Always screw in components until they fully engage.

I Suspension cone 15.0 5cm

I Suspension cone 15.0 5cm

See the User Information booklet 'Doka climb-ing formwork system K' for other ways of fixing anchorages in walls.

9725-411-01

I

a

d

I

9715

-276

-01

a

b

28 999725002 - 02/2017


Suspension points in concrete for reduced loading requirements

Fitting the Bridge edge beam anchor

➤ Nail a Nailing cone to the form-ply (position as shown in shop drawing / assembly plan).

➤ Push the Bridge edge beam anchor onto the nailing cone.

➤ Tie the Bridge edge beam anchor tightly to the rein-forcements with binding wire.This prevents it becoming detached during pouring and vibrating.

After formwork has been struck

➤ Remove the nailing cone from the anchoring point.

a ... concrete cover 4.0 cmb ... placement depth 11.5 cm

➤ Using a Reversible ratchet 1/2", screw in the Screw-in cone until it is fully engaged.

Making the suspension point reusable – lasting protection against corrosion

Where an ungalvanised 'standard' Bridge edge beam anchor 15.0 has been used, you can give the suspen-sion point lasting (electrochemical) protection against corrosion by screwing a Zinc plug 15.0 into the anchor after the formwork has been removed.Field of use: Especially in bridge-building: ▪ piers ▪ superstructuresFor suspension points which are intended to be re-usa-ble in many years' time, when the time comes to reha-bilitate the structure.

WARNING➤ Use of the Bridge edge beam anchor 15.0 is

only permitted up to Load Class 3. It is forbidden to place formwork or heavy loads on the platform!

Comply with the General Building-Inspectorate Approval (Z-21.6-1982)!

A Nailing cone 15.0B Sealing ring

Make sure that the sealing ring is fitted cor-rectly!

C Bridge edge beam anchor 15.0

☞ If statically required – place extra reinforcement steel.

9418

-203

-01AB

9418-204-01

C

A Nailing cone 15.0

E Screw-in cone 15.0

9418-205-01

a

b

A

E

9418-207-01


29999725002 - 02/2017

Suspension points in concrete – insulation up to 11 cm thick

Tools needed: ▪ Reversible ratchet 1/2" ▪ Reversible ratchet 3/4" ▪ Universal cone spanner 15.0/20.0

Positioning point (with hole drilled through form-ply)

➤ Drill a diam. 30 mm hole in the form-ply (position as shown in the project plan).

➤ Screw a stop anchor or pigtail anchor into the Sus-pension cone 15.0 for insulation up to 11 cm.

➤ Insert a Cone screw Rd28 through the hole drilled in the form-ply, screw it into the cone and tighten it.

a ... 0.5 cm

Note:Suspension cones 15.0 for insulation up to 11cm are supplied with Sealing sleeves (D) . Every time the cones are re-used, fit them with new sealing sleeves first.

Positioning point (with no hole drilled through form-ply)

e.g. where there is a Doka beam or the profile of a framed formwork panel directly behind the location of the positioning point.➤ Nail a Positioning disk Rd28 to the form-ply (position

as shown in project plan).➤ Screw the Suspension cone 15.0 for insulation up to

11 cm onto the Positioning disk Rd28.➤ Screw the stop anchor or pigtail anchor into the Can-

tilever positioning cone until fully engaged.

a ... 0.5 cm

Note:Suspension cones 15.0 for insulation up to 11cm are supplied with Sealing sleeves (D) . Every time the cones are re-used, fit them with new sealing sleeves first.

A Stop anchor 15.0 or Pigtail anchor 15.0C Suspension cone 15.0 f. insulation up to 11cmD Sealing sleeve 15.0 f. insulation up to 11cmE Depth markF Cone screw Rd28G Longitudinal reinforcement and U-reinforcements, min. diam.


0.5 cm distance between depth mark and cone.

9725-412-01

a

F

E

G

A Stop anchor 15.0 or Pigtail anchor 15.0C Suspension cone 15.0 f. insulation up to 11cmD Sealing sleeve 15.0 f. insulation up to 11cmE Depth markF Positioning disk Rd28G Longitudinal reinforcement and U-reinforcements, min. diam.


0.5 cm distance between depth mark and cone.

9725-413-01

a

FE

G

30 999725002 - 02/2017


Before pouring

➤ Check all positioning points and suspension points once again.

Suspension point

➤ Unscrew the Positioning disc Rd28 with a Reversible ratchet 1/2".When carefully fitted, and removed without using force, the Positioning disc Rd28 can be used several times over.

➤ Screw in the Cone screw RD 28 until fully engaged, and tighten using the Reversible ratchet 1/2".

d ... min. 16.0 cm

Dimension 'a' (installation depth)

Suspension point fixed in a hole subsequently drilled in the concrete

In concrete walls

Using Rock anchor spreader unit 15.0 + Suspen-sion cone 15.0 with collar

a ... Depth of drilled hole min. 250 mmh ... 6.5 cm

Extra components needed for preparing the suspen-sion point: ▪ Tensioning instrument B, consisting of

- 1 hollow-piston cylinder- 1 hydraulic hand pump- 1 pressure support- 1 carrying case

▪ Rock anchor installation tube ▪ Tie rod wrench 15.0/20.0 ▪ Super plate 15.0 ▪ Rock drill-bits diam. 37 or 38 mmor ▪ Tensioning instrument 300kN, consisting of

- 1 hollow-piston cylinder RH302- 1 hydraulic hand pump- 1 pressure support C- 1 carrying case- 1 Rock anchor installation tube

▪ Tie rod wrench 15.0/20.0 ▪ Super plate 15.0 ▪ Rock drill-bits diam. 37 or 38 mm

Acceptance test➤ Every anchoring point must undergo acceptance

testing.

➤ Warning against not screwing in the sus-pension cones sufficiently far: The resulting reduction in the load-bearing capacity may cause the suspension point to fail, leading to injury and damage.

➤ Never mix components that have different depths of concrete cover - this causes the screw-in depths to be insufficiently deep.

➤ Always screw in components until they fully engage.

F Cone screw RD 28

Pigtail anchor 15.0 92.5 cmStop anchor 15.0 16cm 55 44.6 cm

9725-414-01F

a

d

A Rock anchor spreader unit 15.0 (expendable anchoring compo-nent)

B Tie rod 15.0C Suspension cone 15.0 with collar

Before using, be sure to read and follow the directions in the installation instructions for the Rock anchor spreader unit 15.0 and Suspen-sion cone with collar 15.0!

☞ The Tensioning instrument B cannot be com-bined with the Tensioning instrument 300kN!

a

9725-393-01

h

A CB


31999725002 - 02/2017



With Suspension plate AK

a ... 60.0 cmb ... min. 18.0 cm


With Suspension profile AK

a ... 113.0 cmb ... min. 18.0 cmc ... max. 30.0 cm

A Suspension plate AKB Insulation, max. 10 cm thickC Doka express anchor 16x125mm

WARNING➤ Use of the Suspension plate is permitted

with Load Class 2 only. It is forbidden to place formwork or heavy loads on the platform!

Minimum load-bearing capacity for dowel-type con-nections (these forces occur simultaneously):Tensile force:5.0 kNShear force: 9.2 kNe.g.: Doka express anchor 16x125mmMinimum value of the characteristic cube compressive strength (fck,cube): 25 N/mm2 (concrete C20/25)

Follow the directions in the 'Doka express anchor 16x125mm' Fitting Instructions!

Installation hint for masonry:Leave out a brick where the suspension plate is to be mounted. The suspension plate can then be dismounted from inside the structure.

➤ Before undoing the Express anchor or dowel, make sure that the platforms have been removed from the suspension points!

9725-387-01

AC

a

b

B

9725-202-01

A Suspension profile AKB InsulationC Facing brickworkD Doka express anchor 16x125mm

WARNING➤ Use of the Suspension profile is permitted


Minimum load-bearing capacity for dowel-type con-nections (these forces occur simultaneously):Tensile force:5,0 kNShear force: 9.2 kNe.g.: Doka express anchor 16x125mmMinimum value of the characteristic cube compressive strength (fck,cube): 25 N/mm2 (concrete C20/25)




9725-416-01

AD

C

a

c

b

B

9725-419-01

32 999725002 - 02/2017


Loop-type suspension points

Thanks to the long drop-in rods, in most cases no extra safeguards are needed to protect against accidental lift-out of the platforms.

Suspension point in concrete floor-slab – without insulation (standard suspension point)

with Suspension loop ES

a ... min. 50 cmb ... min. 13.0 cmc ... 17.5 cmd ... 9.0 to 10.0 cme ... 8.0 cmf ... 4.0 cm

☞ Important note:When platforms are mounted in exposed loca-tions (e.g. on tall buildings with closed facades where the platforms are mounted near the top of the building and a storm warning has been given), extra precautions must be taken against accidental lift-out.(e.g. join the platform and the suspension points with a Quick-locking strap 55cm).

A Suspension loop ES

☞ Do not deform (bend, buckle etc.) Suspension loops!

Characteristic cube compressive strength of the con-crete (fck,cube): min. 10 N/mm2

Restriction applicable when used in Germany: ▪ No approval is necessary for steel loop-type sus-

pensions compliant with module B 119 issued by Germany's employers' liability insurance associa-tion of the construction industry (BGBau B 119).

9725-417-01

A

a

d

c

e

ff

b


33999725002 - 02/2017



with Suspension plate ES

a ... 60.0 cmb ... min. 18.0 cmc ... 7.7 cm


With Suspension profile ES

a ... 113.0 cmb ... min. 18.0 cmc ... max. 30.0 cmd ... 7.7 cm

A Suspension plate ESB Insulation, max. 10 cm thickC Doka express anchor 16x125mm

WARNING➤ Use of the Suspension plate is permitted






9725-389-01

AC

a

b

c

B

9725-420-01

A Suspension profile ESB InsulationC Facing brickworkD Express anchor 16x125mm

WARNING➤ Use of the Suspension profile is permitted






9725-415-01

AD

C

a

c

b

d

B

9725-421-01

34 999725002 - 02/2017

Assembly User Information Folding platform K

AssemblySet-up procedure

Doka folding platform K

➤ Lift the stacked platforms off the truck by crane or forklift truck, and set them down on a flat, paved sur-face.

Separating the platforms

➤ Attach the four-part lifting chain to the crane hoisting points at the front and to the extra lifting bows at the rear.

Putting up the railings

➤ Tilt up the rear railings. When you reach the stop, lift the railings and slot them into place.

Folding platform K

Attaching the crane

➤ Pull the lifting bows up out of their recesses, attach the four-part lifting chain (e.g. Doka 4-part chain 3.20m) and raise the Folding platform K.

☞ Only attach and lift 1 platform at a time.

A Doka folding platform KB Doka 4-part chain 3.20mC Lifting bow

C

BA

9725-405-03

A Doka folding platform KD Rear railing

B Doka 4-part chain 3.20mE Lifting bow (at front)F Lifting bow (at rear)

9725-405-01

D

A

9725-405-02

B

E F

User Information Folding platform K Assembly

35999725002 - 02/2017

Pulling out the pressure rod

Bolting the vertical rod in place

➤ Tilt up the vertical rod and fix it by inserting the U-bolt.

➤ Secure the U-bolt with the red safety clip to prevent it being opened accidentally.

The Folding platform K is now ready for use.

Hanging the Folding platform K into place

For all cone-type suspension points, the rule is:➤ Raise the Folding platform K with a four-part lifting

chain.

This raises the front lifting bows, opening the anti-lift-out guard.

➤ Once the Folding platform K is suspended from the suspension cone, the load is removed from the four-part lifting chain.

The lifting bows drop into the starting position, auto-matically securing the platform against accidental lift-out.

CAUTIONAfter being released, the pressure rod swings downwards!➤ Hold the pressure rod in one hand.➤ Then, with the other hand, lift up the red

safety clip and pull out the U-bolt as far as it will go.

➤ Gradually lower the pressure rod by hand.

G Safety clip (red)H U-boltI Pressure rod

G Safety clip (red)H U-boltJ Vertical rod

9725-430-02

G

I

H

9725-430-03

J

G

H

'Locked' position = lifting bow is flush with decking.

9725

-418

-01

9725

-249

-01

36 999725002 - 02/2017


Length adjustment

with Closure platform 3.00m

This ready-to-use, fold-down platform is the quick way of making closures up to 2.50 m long, and corner con-figurations.Other features include: ▪ Long service life thanks to its sturdy design and gal-

vanised steel railings.

System dimensions:

Preparing the platform

1) Tilt up the railings and slot them into place at 15°.In this form, the Closure platform is ready for use as a corner decking unit.

2) Fold out the hinged part.In this form, it is ready for use as a closure deck-ing unit.

The integral crane hoisting points enable the Closure platform to be lifted safely using a four-part lifting chain.

☞ Important note:In exposed locations (e.g. on tall buildings with closed facades where platforms are mounted near the top of the building and a storm warning has been given), loose deck-boards and clo-sure platforms must be secured against acci-dental lift-out.(e.g. join the platform railings and the guard rails of the closure platform using two con-nected Quick-locking straps 55cm).

Hinged part folded out Hinged part folded in

9725-208-01

9725

-352

-01

188

15°15°160

116

343

300

88

105

62

9725-207-01

1

2

9725-224-01


37999725002 - 02/2017

Length adjustment

➤ Position the Closure platform 3.00m across the mid-dle of the closure zone.

Manhole

➤ Position the Closure platform 3.00m across the mid-dle of the closure zone.Front hinged part must be folded back.

b ... 86 cm

with planks

Closures and corner transitions can also be made using field-built solutions.

Length adjustment

Floor planking:➤ Lay down planks with a min. cross-section of 20x5

cm. Minimum overlap 75 cm!

Setting up guard rails using the Universal railing shackle:➤ Attach the Universal railing shackles to the side rail-

ings of the folding platform using two 2.8x65 nails.➤ Insert guard-rail boards (min. 15x3 cm) into the Uni-

versal railing shackles and fix them with two 2.8x65 nails on each side. Minimum overlap 15 cm!

Nailing the railings on directly:➤ Fix the guard-rail boards (min. 15x3 cm) with two

2.8x65 nails on each side. Minimum overlap 15 cm!

Note:The plank and board thicknesses given here comply with the C24 category of EN 338.Observe all national regulations applying to deck-boards and guard-rail boards.

☞ Do not exceed the max. closures a, depending on the usage situation.See the following sections: ▪ Working platform with formwork ▪ Working platform without formwork ▪ Protection platform

☞ Do not exceed the max. closures, as stated for the length adjustment.

9725-298-01a

9725-297-01

b

A Attach a guard-rail board with a Universal railing shackle or with two 2.8x65 nails on each side

☞ Do not exceed the max. closures a, depending on the usage situation.See the following sections: ▪ Working platform with formwork ▪ Working platform without formwork ▪ Protection platform

9725-206-01

A

a

38 999725002 - 02/2017


Outside corners

The system offers several different ways of dealing with corner zones.


The whole unit can be lifted and repositioned in a single crane cycle. This makes it possible to arrange platform layouts very quickly, even in corner zones.

1) ... Dimension when using cone-type suspension points 2) ... Dimension when using the Bow head K-ES

Note:When used with formwork, comply with the permitted service load and closures stated in the section 'Working platform with formwork'.

Permitted live load: 3.0 kN/m2 (300 kg/m2)Load Class 4 to EN 12811-1:2003

AC

C

9725-452-01

401)22,5362)

Load Class 2Permitted service load 1.5 kN/m2 (150 kg/m2)


A Doka folding platform K outside cornerB Closure platform 3.00mC Doka folding platform K

A

B250

C

C

9725-465-01

A

B150

C

C

C

9725-451-01

A

A

B250

C

C

9725-448-01

☞ Important note:With Load Class 4, closures on the Folding platform K outside corner are forbidden.


39999725002 - 02/2017

Other corner solutions

Corner solution with closure platform

➤ Set down the Closure platform 3.00m on the two cor-ner folding platforms with equal overlap to either side (no additional fixing required).Front hinged part must be folded back.

c ... 15 to 75 cmd ... 75 cme ... min. 130 cmf ... min. 90 cm

Corner solution with planks

c ... 15 to 75 cmd ... 75 cme ... min. 130 cmf ... min. 90 cm

➤ Cover the corner zone with planks (min. 20x5 cm). Minimum overlap 20 cm!

➤ Fix the guard-rail boards (min. 15x3 cm) with two 2.8x65 nails on each side. Minimum overlap 15 cm!

☞ Minimum overlap 20 cm!

B Closure platform 3.00mC Doka folding platform K

BC

C

9725-296-01

c

d

ef

C Doka folding platform KD Planks

The Universal railing shackle can be used in the same way as with the length adjustment.

DC

C

9725-247-01

c

d

ef

40 999725002 - 02/2017


Set-up procedure Doka folding platform K outside corner

➤ Lift the stacked platforms off the truck by crane or forklift truck, and set them down on a flat, paved sur-face.

Separating the platforms

➤ Attach the four-part lifting chain to the crane hoisting points at the front and to the extra lifting bows at the rear.The lifting chain can be attached to stacked plat-forms in the same way.

➤ Place the waist-level guardrail and toeboards to one side.


➤ Tilt up both rear railings. When you reach the stop, lift the railings and slot them into place.

➤ Fit the waist-level guardrail and the toeboards into their respective holding plates.

➤ On the opposite side, secure each hinge with a hinge pin and spring cotter d2.

Attaching the crane

➤ Pull the lifting bows up out of their recesses, attach the four-part lifting chain (e.g. Doka 4-part chain 3.20m) and raise the Folding platform K.

A Doka folding platform K outside cornerB Doka 4-part chain 3.20m

A Doka folding platform K outside cornerC Waist-level guardrail for outside cornerD Toeboards for outside corner

E Rear railing

TR981-208-01

B

A

ATR981-203-01

CD

TR981-204-01

EE

C Waist-level guardrail for outside cornerD Toeboards for outside cornerF HingeG Hinge pin + spring cotter d2

☞ Only attach and lift 1 platform at a time.

B Doka 4-part chain 3.20m

DC

TR981-205-01

F

G

D

TR981-205-02

TR981-205-03

B


41999725002 - 02/2017





Assembling the pressure-strut unit

1) Pull out the spring cotter d3.2) Pull out the Double bolt D10/85.3) Turn the swivel profile to the fastening unit.

4) Push the Double bolt D10/85 into the fastening unit.5) Secure the Double bolt D10/85 with the spring cot-

ter d3.

The Folding platform K outside corner is now ready for use.

Hanging the Folding platform K outside corner into place

This is done in the same way as with the Folding plat-form K.




H Safety clip (red)I U-boltJ Pressure rod

H Safety clip (red)I U-boltK Vertical rod

9725-429-02

H

J

I

9725-429-03

K

H

I

A Doka folding platform K outside cornerB Doka 4-part chain 3.20mL Folding bracket KM Pressure-strut unit of outside corner

9725-429-05

1

23

9725-429-05

4

5

9725-429-04

B

A

L

M

42 999725002 - 02/2017


Inside corners


Its special rear railing distinguishes the Folding plat-form K inside corner from the Folding platform K 3.00m. It ensures that safe guard rails are in place in the area of inside corners.

Note:The narrowside of the Folding platform K inside corner where the rear railing is open must be facing the wall.

1) ... Dimension when using cone-type suspension points 2) ... Dimension when using the Bow head K-ES 3) ... Fixed dimension in corner zone (Folding platform K inside cor-ner)

Permitted service load: 6.0 kN/m2 (600 kg/m2)Load Class 6 to EN 12811-1:2003

2641)

2682)

C A

C

9725-431-01

15075 803)



A Doka folding platform K inside cornerB Closure platform 3.00mC Doka folding platform K

C A

C

B

9725-453-01

250

C A

C

B

9725-460-01

150

☞ Important note:Closures on the Folding platform K inside cor-ner are forbidden with Load Class 4 or higher.


43999725002 - 02/2017

Note:When used with formwork, comply with the permitted service load and closures stated in the section 'Working platform with formwork'.

Set-up procedure

➤ Tilt up the rear railings. When you reach the stop, lift the railings and slot them into place.

The set-up procedure from now on is the same as for the Doka folding platform K.

Hanging the Folding platform K inside corner into place

This is done in the same way as with the Folding plat-form K.

WARNINGRisk of platform tipping over when setting down formwork on the Folding platform K inside cor-ner!➤ Where loop-type suspension points are

being used, it is forbidden to set down form-work on the Folding platform K inside corner!

➤ Where cone-type suspension points are being used, the anti-liftout guard of the Fold-ing platform K inside corner must be active!

➤ Set formwork down first on the long side of the Folding platform K inside corner and then on the narrowside.

Formwork must first be removed from the nar-rowside when stripping the formwork. A Doka folding platform K inside corner

D Rear railing

☞ Important note:The Folding platform K inside corner must always be hung into place first, to prevent any collisions with adjacent folding platforms.When repositioning and dismounting the plat-forms, the Folding platform K inside corner is always the last to be lifted away.

9725-428-03

D

A

44 999725002 - 02/2017


Bridging openings in walls

For bridging wall-openings in the horizontal, either of the following may be used: ▪ Multi-purpose waling WS10 Top50 ▪ Squared timbersThese bridging beams are also suitable for use as sup-porting profiles in masonry construction.

Can also be mounted to the folding platform when this is folded closed. The bridging beam can remain on the closed folding platform.

Areas of use

* Load Class 3: 1.90m without formwork, without suspended plat-form. Load Class 2: 1.90 m with formwork, without suspended platform. Formwork shored from floor slab. (See the section headed 'Working platform with formwork', column 2)

☞ Important note: ▪ Fix the bridging beam so that it cannot fall off! ▪ The horizontal bridging beam must always

be resting against a construction with suffi-cient load-bearing capacity!

With Multi-purpose waling WS10 Top50

With squared timbers 12x14 cm

Length of Multi-purpose waling:2.75 m or 3.50 m a ... 14 cm

Possible ways of mounting to platform: ▪ Connecting pin 25 cm with spring

cotter 5mm or

▪ Hexagon screw M20x90 with nut and spring washer

▪ Fix with binding wire

9725-221-01

9725-274-01 9725

-275

-01

a

Opening width bBridged using Working platform Protection platform

Multi-purpose waling WS10 Top50 2.20 m 4.00 m

Squared timbers 12x14 cm * 1.90 m

9725-276-01

b


45999725002 - 02/2017

Platform assembled from single brackets

Makes it possible to choose any bracket spacing and any length of platform, for constructing closure plat-forms (of e.g. less than 3.0 m in length) and special shapes for use in corner zones.

Assembly

Separating the brackets

➤ Lift the Folding brackets K off the truck and set them down on a flat surface.


➤ Tilt up the railings. When you reach the stop, lift the railings and slot them into place.

➤ Place the Folding bracket K on its side, on timber supports on the ground.


➤ Raise the red safety clip and pull out the U-bolt as far as it will go.

➤ Pull out the pressure rod.

Max. influence width per bracket 1.50 m

☞ Important note:When making project-specific platforms, observe the following points: ▪ Position brackets as symmetrically as possi-

ble and keep their cantilever short. ▪ Ensure that all loads are applied centrally. ▪ The stability of the platforms must be

ensured during all phases of the construction work!

CAUTIONRisk of platforms tipping over when loads are applied non-centrally.If there is no way to avoid cantilevers extending out to one side, observe the following points:➤ Choose the widest possible bracket spacing

in relation to the cantilever!➤ Allow for the greater influence of the bracket

in the cantilevering region!➤ Contact your Doka technician for information

on further measures to prevent platforms tip-ping over.

The anti-liftout guards are not suitable for sus-taining planned forces! The anti-liftout guard is only designed to prevent the platform from being accidentally lifted out of its suspension points while work is in progress.

A Folding bracket K

A

9725-459-01

B Railing

C Red safety clipD U-boltE Pressure rod

B

9725-459-02

9725-459-03

C D

E

46 999725002 - 02/2017


Note:In cases where the bracket is unfolded while sus-pended from the crane:




Fitting the bracing

➤ Prepare an assembly bench.➤ Prepare the bracing.➤ Tilt up the Folding brackets K and stand them

spaced the specified centre-to-centre distance apart (see shop drawing / assembly plan).

➤ Secure them so that they cannot topple over.➤ The length of the scaffold tubes used will depend on

the centre-to-centre spacing of the brackets.➤ Brace the Folding brackets K in the horizontal, with 4

screw-on couplers and 2 scaffolding tubes.➤ Mount a scaffold tube as a diagonal stiffening rein-

forcement between the brackets, using 2 swivel cou-plers.

Distance between screw-on coupler and swivel cou-pler: max. 160 mm.

This set-up scheme is for platform units with 2 brackets. On platform units with 3 brackets, the number of cou-plers and scaffolding tubes will need to be adjusted accordingly.




C Red safety clipD U-boltE Pressure rod

C Red safety clipD U-boltF Vertical rod

C D

E9725-459-05

9725-459-04

F

C D

A Folding bracket KG Scaffold tube 48.3mm (length = centre-to-centre distance +

20 cm)H Scaffold tube 48.3mm (length = centre-to-centre distance +

50 cm)I Screw-on coupler 48mm 50J Swivel coupler 48mm

9725-424-01

AG

H

I J


47999725002 - 02/2017

Attaching the platform decking

Note:The plank and board thicknesses given here comply with the C24 category to EN 338.Observe all national regulations applying to deck-boards and guard-rail boards.

➤ Place the braced Folding brackets K onto a trestle.

➤ Lay deck-boards onto the bracket. (Cut them to size as shown in the illustration)

a ... length of platform b ... centre-to-centre distance c ... 13 cm d ... 6 cm e ... ø 2.4 cm f ... 141 cm g ... 154 cm h ... 177 cm

➤ Screw on an outside reinforcing board at each end of the platform (for each reinforcing board 1 Universal countersunk-head screw per deck-board).

➤ Screw on the middle reinforcing board centred between the brackets (2 Universal countersunk-head screws per deck-board).

➤ Use the square bolts included in the scope of supply to secure the deck-boards to the brackets (6 pcs. included in scope of supply of the Folding bracket K).

➤ On each bracket, fasten handrail planks onto the handrail post using carriage bolts M 10x110, spring washers A 10 and hexagon nuts M 10 (5 bolts are included with each Folding bracket K).

Note:In corner zones, or where the corners are not right-angled, the platform planking must be trimmed accord-ingly.Mount passage units as shown in the shop drawing / assembly plan.

A Plank 25/5 cmB Outside reinforcing boardC Middle reinforcing boardD Drilled hole for securing panel strut

9725-424-02

D

a

b

c

c

d

e

g

h

f

d

A

9715-2 -0151

CB B

E Folding bracket KF Threaded fasteners in scope of supply

☞ ➤ Attach guard rails so as to comply with the applicable national regulations.

F

9715-2 -051 2

E

97 5- -02 424 3

48 999725002 - 02/2017

Repositioning User Information Folding platform K

RepositioningMoving the platform

Instructions for safe repositioning of the Folding platform K

The platforms are normally lifted using suitable four-part lifting chains such as the Doka 4-part chain 3.20m.Use the Platform transport fork K/M or the Transport fork K/M plus in the following usage situations: ▪ when it is not possible to walk onto the platform to

attach the four-part lifting chain; ▪ when the platform is being used as a sloping-rooftop

fall barrier and cannot be lifted out by four-part lifting chain because of the projecting eaves.

☞ Important note:As early as in the planning phase, considera-tion should also be given to the order of reposi-tioning and dismounting the very last platform! ▪ In general, the last platform is where there

are access and exit routes for the regular work sequence. Vertical access is usually provided by stair towers or aerial work plat-forms.

▪ If there are window or door openings in the façade, then the last platform can be one that enables access through these façade open-ings.

▪ Local regulations, or the result of a hazard assessment carried out by the erector, may make it necessary to use personal fall-arrest systems (PFAS) during repositioning.

▪ When one platform is repositioned, this opens up exposed fall-hazard locations on the remaining units. Each of these openings have to be closed off with a side railing or else a barrier has to be set up at least 2.0 m short of the drop-off edge.

▪ The personnel in charge of the repositioning operation are responsible for positioning the access prohibition barriers correctly.

When platforms that are anchored to the struc-ture with cone-type suspension points are repositioned with a transport fork, observe the following:

➤ Working from the second-last platform, dis-engage the anti-liftout guard of the last plat-form. The red lifting bow (H) must be shifted into the stand-by position (fixed in the short slot).

➤ Re-lock the anti-liftout guard. After hanging the platform into place on the suspension cone, move the lifting bow back into the locked position (fixed in the long slot so that the lifting bow is flush with the plat-form decking).

9725-295-01

H

User Information Folding platform K Repositioning

49999725002 - 02/2017

Transport fork K/M plus Platform transport fork K/M

Follow the directions in the 'Transport fork K/M plus' Operating Instructions!

☞ Check before using with the Folding platform K:The tilting unit must be in the rear pin-fixing position, and fixed in place.

Dimension hWith loop-type suspension points min. 30 cmWith cone-type suspension points min. 13 cm

A Tilting unitB Slinging point for tag-lineC Tag-line (not included with product)

A

92864-205-02

92864-207-05

B

C

h

Follow the directions in the 'Platform transport fork K/M' Operating Instructions!

☞ Check before using with the Folding platform K:Telescopic beam must be completely extended, and fixed in place.

Dimension hWith loop-type suspension points min. 30 cmWith cone-type suspension points min. 13 cm

A Telescopic beamB Slinging point for tag-lineC Tag-line (not included with product)

A

9725-294-01

h

B

C

50 999725002 - 02/2017

Protection platform User Information Folding platform K

Protection platform

General remarks

▪ Protection platforms must conform to Load Class 2 or higher.

▪ For the types of suspension point and closures, con-sider the specifications given for working platforms without formwork.

Fall-stop scaffold

a ... 1.85 mb ... 2.13 md ... 0.95 m

*min. 1.00 m as per ÖNORM B 4007

B Guard rail

☞ Important note:Regarding the safety-relevant application and use of our products, strict compliance with the industrial safety laws, standards and regula-tions and other safety-related regulations as issued and amended and applicable in the country or state of use is essential.In accordance with the applicable regulations, guard rails are the first measure to be taken.

Regulation Drop height h Dimension c

As per DIN 4420-1max. 2.0 m min. 0.90 m*max. 3.0 m min. 1.30 m

Country Regulation Drop height h Dimension cGermany ASR A2.1 max. 2.0 m

Norway, Great Britain

Health and Safety at Work

Actmax. 2.0 m

Czech Republic

ČSN 738106,Government Ordinance 362/2005

max. 1.5 mSee Diagram

in ČSN 738106

c

h

b

a

9725-350-01

d

B

User Information Folding platform K Protection platform

51999725002 - 02/2017

Sloping-rooftop fall barrier

As per DIN 4420-1

a ... eaves depthh ... max. 1.50 m

Areas of use

Dimensioning example

for determining the max. dimension 'h' (from decking to edge of eaves).Given: Eaves depth 'a' = 0.80 mResults (possibilities): ▪ Folding platform (standard), as shown in area (W)

h = max. 0.70 m or ▪ Folding platform with Handrail extension K, as

shown in area (X) h = max. 1.40 m

As per ÖNORM B 4007

a ... min. 60 cm

A Handrail extension K

☞ ▪ When the Handrail extension K is used, the max. closure length is 1.00 m

▪ Allow for the min. lift-out distance b of 30 cm!

Dimension a [m]

h [m

] (fr

om d

ecki

ng to

edg

e of

eav

es)

W Folding platform – standardX with Handrail extension K

a

A

h

b

9725-370-01

9725-101

0.8

1.0

1.2

1.4

0.6

0.9

1.1

0.7

0.5

1.3

1.5

0.40.10 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3

W

X

A Handrail extension K

☞ ▪ When the Handrail extension K is used, the max. closure length is 1.00 m

▪ Allow for the min. lift-out distance b of 30 cm!

b

A

a

9725-423-01

52 999725002 - 02/2017

Protection platform User Information Folding platform K

Handrail extension K

The Handrail extension K extends the range of use of the Folding platform K as a fall barrier for work on slop-ing roofs (see diagram in the section headed 'Sloping-rooftop fall barriers').

Assembly

➤ Push the Handrail extension K all the way into the handrail posts of the Folding platform K and the Fold-ing platform K outside corner.

➤ Insert the scaffold tubes into the quick-acting cou-plings on the handrail extensions. Wedge in place firmly.

➤ Link the scaffold tubes at the corners with Swivel couplers 48mm.

➤ Fix the safety nets in place.

☞ Important note:When the Handrail extension K is used, the max. closure length is 1.00 m

Folding platform K outside corner Closure platform 3.00m In-situ bridging using planks

A Handrail extension KB Scaffold tube 48.3mmC Swivel coupler 48mmD Safety netE Doka folding platform K outside cornerF Closure platform 3.00mG Planks

9725-432-01

D

E

BC

B

A

9725-229-01

D

F

BC

B

A

9725-230-01

D

G

BC

B

A

User Information Folding platform K Protection platform

53999725002 - 02/2017

Protective canopy

The components of the Folding platform K comply with the requirements for erecting protective canopies as per EN 12811-4.

b .. Sidewall height

Cover the gaps between the decking and the wall, and between the platforms.Board thicknesses: ▪ 20/3.5 cm for spans of up to 1.50 m ▪ 24/4.5 cm for spans of up to 2.50 m

A Extra guard-rail boardB Cover for gap

Sidewall height b

As per DIN 4420-160.0 cm

Extra guard-rail boardrequired

As per ÖNORM B 4007

50.0 cmCorresponds to the standard height –

therefore no extra guard-rail board required

b

9725-358-01

AB

54 999725002 - 02/2017

Other possible areas of use User Information Folding platform K

Other possible areas of useBridging storey-high openings

Support lengthening pieces are required in situations where the pressure point of the folding platform is not resting against part of the structure (as in e.g. skeleton-type construction, wall openings, etc.).For loadability data, see: ▪ Working platform with formwork ▪ Working platform without formwork

Support lengthening piece with Multi-purpose waling and Strut

The Support lengthening piece consists of:

* Fixing items included with product.

Folding platform K 3.00m / 4.50m Folding platform K inside corner Folding platform K outside corner

N° of items

Item Designation Folding platform K 3.00m

Folding platform K 4.50m

Folding platform K inside corner

Folding platform K outside corner

A Multi-purpose waling WS10 Top50 3.50m 2 3 2 2B Swivel coupler 48mm 2 4 2 1C Screw-on coupler 48mm 50 4 6 4 2D Scaffold tube 48.3mm 2.00m 2 -- 2 --E Scaffold tube 48.3mm 2.50m 1 2 1 --F Scaffold tube 48.3mm 3.50m -- 2 -- --G Facade precast member clamp V* 2 3 2 2H Strut* 2 3 2 2

I Pin D16/112 (art. n° 500403330) 2 3 2 2

J Linch pin 6x42 (DIN 11023) 2 3 2 2K Scaffold tube 48.3mm 1.00m -- -- -- 2

9725

-426

-01

DF

AG

IJ

E

H

B

C

9725

-435

-01

DF

AG

IJE

H

B

C

9725

-434

-01

K

AG

IJ

H

B C

User Information Folding platform K Other possible areas of use

55999725002 - 02/2017

Practical example

a ... possible storey heights 212 to 457 mb1 ... with Facade precast member clamp V: 211 - 253 and 367 - 442 cm (region 'f' cannot be used) b2 ... with squared timber: 211 - 456 cmc ... 6.4 cmd ... 107 cme ... 14 cm

Note:As an alternative to the Facade precast member clamp V, a squared timber 12x14 cm can be fixed onto the multi-purpose walings with square bolts M10x160.

CAUTION➤ The Facade precast member clamp V must

be mounted within range 'b', irrespective of the length of the multi-purpose walings.

9725

-269

-01

a

b

cd

e

f

9725-212-01

56 999725002 - 02/2017


Support lengthening piece with Support girder and Strut

The Support lengthening piece consists of:

The Support lengthening piece is supplied knocked-down, incl. all necessary fixing items.

Practical example

a ... Possible storey heights 2.12 to 3.34 mb ... 333.0 cmc ... 6.4 cmd ... 107.0 cme ... Hole-grid 12x10.0 cm = 120.0 cm

N° of items

Item Designation

Fold

ing

plat

form

K 3

.00m

and

Fold

ing

plat

form

K in

side

cor

ner

Fold

ing

plat

form

K 4

.50m

A Support girder 2 3B Bearing profile 2 3C Screw-on coupler 48mm 50 2 3D Horizontal strut 1.35m 1 2E Horizontal brace d2 175 1 2F Scaffold tube 48.3mm 2.00m 1 --G Scaffold tube 48.3mm 3.50m -- 1H Strut 2 3

9725-211-01

E

D

F G

H

A

B

C

☞ Important note:The Folding platform K outside corner can only be used with multi-purpose waling and strut.

a

b

cd

e

9725-268-01


57999725002 - 02/2017

Assembly

➤ Place the Support girder on level ground. Fasten the Bearing profile onto the Support girder in the desired position (will depend on the storey height), using a Pin D16/112, and secure with a linch pin.

➤ Mount the Screw-on coupler 48mm 50 in the top hole on the Support girder.

➤ Place the 2nd Support girder on the floor beside the 1st (on 4.50 m wide platforms, a 3rd Support girder may also be needed). Centre-to-centre distance: 1.50 m. (Mount the Bearing profile and the Screw-on coupler 48mm 50 as described above).

➤ Fasten the Horizontal strut 1.35m to the Bearing pro-file with M16x45 hexagon bolts.

➤ Mount the Horizontal brace d2 175 to provide diago-nal bracing, bolting it on with M16x45 hexagon bolts.

➤ Mount a Scaffold tube 48.3mm into the Screw-on couplers 48mm 50, to provide horizontal bracing.

➤ Using a Pin D16/112, insert the Support girder into the borehole (V) on the folding platform, and secure with a linch pin.

➤ Using a Pin D16/112, insert the Strut into the bore-hole (W) on the folding platform, and secure with a linch pin.

➤ Gradually raise the folding platform:The Support girder and Strut automatically pivot downwards.

➤ Pivot the Strut forward into the Support girder, fix it in place in the borehole (X) with a Pin D16/112, and secure with a linch pin.

The Folding platform K plus Support lengthening piece is now ready for use.

Dismantling

To dismantle, perform the above steps in reverse order.

A Support girderB Bearing profileC Screw-on coupler 48mm 50U Pin D16/112

D Horizontal strut 1.35mE Horizontal brace d2 175F Scaffold tube 48.3mm

9725-236-01

A

B

UC

9725-237-01

x

E

DF

A Support girderH StrutV Borehole on the folding platformW Borehole on the folding platform

H Support girderX Borehole

9725-239-01

W

A

H

V

9725

-240

-01

H

X

58 999725002 - 02/2017


Second workdeck level

with Suspended platform 120 4.30m

For finishing-work on cured concrete surfaces or for disassembly work (e.g. dismounting unneeded suspen-sion points).

Items needed:

The Support lengthening piece is supplied knocked-down, incl. all necessary fixing items (except for *). * site-provided

Preparing the platform decking

➤ Place the deck-boards on trestles.➤ Place platform profiles onto the deck-boards, spaced

apart at the centre-distance of the brackets.➤ Fasten the platform profiles to the deck-boards with

M 10x70 square bolts.➤ Fix planks to the ends of the platforms, and diago-

nally between the platform profiles. (2 nails per deck-board)

➤ Turn over the pre-assembled decking and set it down on the ground.

Note:In corner zones, or where the corners are not right-angled, the platform planking must be trimmed accord-ingly.

☞ Important note:It is not permitted to use the Folding platform K outside corner with a Suspended platform 120 4.30m!

N° of items

Item DesignationFolding plat-

form K 3.00m

Folding plat-form K 4.50m

A Suspended platform 120 4.30m 2 3B Planks and guard-rail boards* -- --

9725-213-01B

A

B

A Platform profiles

9715-260-01

A

9715-260-02


59999725002 - 02/2017

Assembling the suspended platform

➤ Lift the Folding platform K by crane.

➤ Bolt on the inside suspension tube with an M 16x120 hexagon bolt.

➤ Bolt on the outside suspension tube with an M 16x90 hexagon bolt.

➤ Mount the platform profiles of the pre-assembled platform decking to the suspension tubes with 4 hex-agon bolts M16x90 for each profile.

➤ Use an M10x120 square bolt to attach a guard-rail board (min. 15x3 cm) as a toeboard.

➤ Insert guard-rail boards (min. 15x3 cm) into the handrail post plates and fix them with 28x65 nails.


Practical example

a ... 434.0 cmb ... 15.0 cmc ... 115.0 cm

Dismantling

To dismantle, perform the above steps in reverse order.

B Inside suspension tubeC Outside suspension tube

B C

9725-458-01

9725-458-02

9715-256-03

9715-243-029715-243-03

D Guard-rail board min. 15x3 cm

9715-290-02

D

9725

-270

-02

a

cb

60 999725002 - 02/2017


Folding platform K as a base on which to stand the Working scaffold Modul

This method is particularly recommended in situations where it is not possible to erect façade scaffolding from the ground up, e.g. because of an open building pit or because traffic and pedestrian access routes have to be left clear.The high load-bearing capacity of the Folding platform K – coupled with the statically computed scaffold heights given below – greatly extend the folding plat-forms' possible range of use.

Practical example

a ... max. 30 cm

☞ Important note:Only use types of suspension point that are per-mitted for Load Classes 5 and 6.

Sca

ffold

wid

th [m

]

Fiel

d le

ngth

[m]

Version

Sca

ffold

hei

ght [

m]

0.73 3.07 without inside bracket 240.73 3.07 with inside bracket 81.09 2.57 without inside bracket 8

Comply with the General Building-Inspectorate Approval (Z-8.22-906)!

A Sleeper or Steel waling WS10B Working scaffold Modul

a

A

B

9725-437-01


61999725002 - 02/2017

Climbing with the Folding platform K

Climbing formwork K

Simply adding a few standard components to the Folding platform K transforms it into a fully-fledged, tilt-able climbing formwork – the Climbing formwork K. ▪ It is used in situations where formwork has to be

lifted in several casting steps and where retractable formwork is not required.

▪ The formwork-plus-platforms unit is repositioned in its entirety in a single crane cycle.

▪ The formwork is set up and struck with no need for a crane, meaning that the only crane times needed are those for the lifting operations.

Follow the directions in the 'Climbing formwork K' User Information booklet!

9715-243-01

62 999725002 - 02/2017

General remarks User Information Folding platform K

General remarksSideguards on exposed platform-ends

On platforms that do not completely encircle the struc-ture, suitable sideguards must be placed across exposed end-of-platform zones.


Side handrail clamping unit T

How to mount:➤ Fasten the clamping part to the decking of the folding

platform using the wedge (clamping range 4 to 6 cm).

➤ Slot in the railing.➤ Extend the telescopic railing to the desired length

and secure it.➤ Insert toeboard (guard-rail board).

Edge protection system XP

How to mount:➤ Fasten the clamping part of the railing clamp to the

decking of the folding platform using the wedge.➤ Working from below, push the Toeboard holder XP

1.20m onto the Handrail post XP 1.20m. The bracket of the toeboard holder must be pointing downward, facing the platform.

➤ Push on the Handrail post XP 1.20m until it locks ("Easy-Click" function).

➤ Place guard-rail boards on the handrail-post plates and secure them with nails (diam. 5 mm).

A Side handrail clamping unit T with integral telescopic handrailB Guard-rail board min. 15x3 cm (site-provided)C Doka folding platform K

9725-204-01

A

BC

A Guard-rail board min. 15x3 cm (site-provided)B Railing clamp XP 40cmC Handrail post XP 1.20mD Toeboard holder XP 1.20mE Doka folding platform K

D

9725-427-01

C

B

A

E

User Information Folding platform K General remarks

63999725002 - 02/2017

Fall-arrest systems on the structure

Edge protection system XP

▪ Attached with Screw-on shoe XP, railing clamp, Handrail-post shoe or Step bracket XP

▪ Protective grating XP, guard-rail boards or scaffold tubes can be used as the safety barrier

a ... > 1.00 m

Handrail clamp S

▪ Attached with integral clamp ▪ Guard-rail boards or scaffold tubes can be used as

the safety barrier

a ... > 1.00 m

Handrail clamp T

▪ Fixed in embedded anchoring components or reinforcement hoops

▪ Guard-rail boards or scaffold tubes can be used as the safety barrier

a ... > 1.00 m

Handrail post 1.10m

▪ Fixed in a Screw sleeve 20.0 or Attachable sleeve 24mm

▪ Guard-rail boards or scaffold tubes can be used as the safety barrier

a ... > 1.00 m

Follow the directions in the 'Edge protection system XP' User Information booklet!

Follow the directions in the 'Handrail clamp S' User information!

9803

1-20

0-01

aa

9756

-206

-01

Follow the directions in the 'Handrail clamp T' User Information!

Follow the directions in the 'Handrail post 1.10m' User Information!

a

9755

-205

-01

a

9771

-200

-01

64 999725002 - 02/2017




The Folding platforms K are pre-assembled and can be collapsed for easy shipping and storage – no risk of slippage.

This optimum packing density translates into low ship-ping volume and excellent utilisation of the loading area of the truck: ▪ 84 linear metres of Doka folding platforms K per

truck semi-trailerThis corresponds to:

- 28 Folding platforms K 3.00m ▪ 94.5 linear metres of Doka folding platforms K per

truck trailerThis corresponds to:

- 21 Folding platforms K 3.00m +- 7 Folding platforms K 4.50m

Stack of 7 Folding platforms K or of 7 Folding platform K inside corners

Stack of 7 Folding platform K outside corners

a1 ... 234.0 cma2 ... 262.0 cmb ... 210.0 cmc ... 29.0 cmd ... 35.0 cme ... 10.0 cm

Stack of 10 Closure platforms 3.00m

When folded closed, the pre-assembled Closure plat-forms are easy to transport and store.With their high packing density and ideal dimensions, they make highly efficient use of the available storage and shipping capacity.

Note:Only set down stacks of platforms on flat, paved sur-faces.

☞ When stacking Folding platform K inside cor-ners, a squared timber 10x10x30 cm must be inserted to keep each stacked platform horizon-tal.

9725-307-02

D

A

C

9725-446-01

a1

b

dc

e

A Doka folding platform K or Doka folding platform K inside corner

B Doka folding platform K outside cornerC Squared timber 10x10x30 cm D Sleeper, 10 cm high

A Sleeper, 10 cm high

D

B

9725-447-01

a2

b

dc

e

9725-286-01

A

110

17.2

169


65999725002 - 02/2017

Doka skeleton transport box 1.70x0.80m

Storage and transport devices for small items: ▪ durable ▪ stackableSuitable transport appliances: ▪ crane ▪ pallet stacking truck ▪ forklift truckTo make the Doka skeleton transport box easier to load and unload, one of its sidewalls can be opened.

Using Doka skeleton transport boxes 1.70x0.80m as storage units

Max. n° of boxes on top of one another

Using Doka skeleton transport boxes 1.70x0.80m as transport devices

Lifting by crane

Repositioning by forklift truck or pallet stacking truck

The forks can be inserted under either the broadside or the narrowside of the containers.

Utilise the benefits of Doka multi-trip packaging on your site.Multi-trip packaging such as containers, stacking pal-lets and skeleton transport boxes keep everything in place on the site, minimise time wasted searching for parts, and streamline the storage and transport of sys-tem components, small items and accessories.

Max. load: 700 kgPermitted imposed load: 3150 kg

☞ ▪ Multi-trip packaging items that each contain very different loads must be stacked with the heaviest ones at the bottom and the lightest ones at the top!

▪ Rating plate must be in place and clearly leg-ible

Outdoors (on the site) IndoorsFloor gradient up to 3% Floor gradient up to 1%

2 5It is not allowed to stack empty pallets on top of one another!

➤ Only lift the boxes when their sidewalls are closed!

☞ ▪ Multi-trip packaging items may only be lifted one at a time.

▪ Use a suitable lifting chain (e.g. Doka 4-part chain 3.20m). Do not exceed the permitted load-bearing capacity.

▪ Spread-angle max. 30°!

9234-203-01

66 999725002 - 02/2017


Doka multi-trip transport box 1.20x0.80m galv.

Storage and transport devices for small items: ▪ durable ▪ stackableSuitable transport appliances: ▪ crane ▪ pallet stacking truck ▪ forklift truck

Multi-trip transport box partition

Different items in the Multi-trip transport box can be kept separate with the Multi-trip transport box partitions 1.20m or 0.80m.

Possible ways of dividing the box

Using Doka multi-trip transport boxes as storage units


Using Doka multi-trip transport boxes as transport devices

Lifting by crane



Max. load: 1500 kgPermitted imposed load: 7900 kg


▪ Rating plate must be in place and clearly leg-ible

A Slide-bolt for fixing the partition

Tr75

5-20

0-02

A

Multi-trip transport box partition Lengthways Crossways

1.20m max. 3 partitions -0.80m - max. 3 partitions






Tr755-200-04 Tr755-200-05

9206-202-01


67999725002 - 02/2017

Doka stacking pallet 1.55x0.85m and 1.20x0.80m

Storage and transport devices for long items: ▪ durable ▪ stackableSuitable transport appliances: ▪ crane ▪ pallet stacking truck ▪ forklift truckThe Bolt-on caster set B turns the stacking pallet into a fast and manoeuvrable transport trolley.

Using Doka stacking pallets as storage units

Max. n° of units on top of one another

Using Doka stacking pallets as transport devices

Lifting by crane


Follow the directions in the 'Bolt-on castor set B' Operating Instructions!

Max. load-bearing capacity: 1100 kgPermitted imposed load: 5900 kg


▪ The rating plate must be in place and clearly legible.



☞ ▪ How to use with bolt-on castor set: Always apply the fixing brake when the con-tainer is 'parked'.When Doka stacking pallets are stacked, the bottom pallet must NOT be one with a bolt-on caster set mounted to it.



▪ Load the items centrically. ▪ Fasten the load to the stacking pallet so that

it cannot slide or tip out. ▪ When lifting stacking pallets to which Bolt-on

castor sets B have been attached, you must also follow the directions in these Operating Instructions!


aDoka stacking pallet 1.55x0.85m max. 4.0 mDoka stacking pallet 1.20x0.80m max. 3.0 m

☞ ▪ Load the items centrically. ▪ Fasten the load to the stacking pallet so that

it cannot slide or tip out.

92815-2 -0124

a

= =

68 999725002 - 02/2017


Doka accessory box

Storage and transport devices for small items: ▪ durable ▪ stackableSuitable transport appliances: ▪ crane ▪ pallet stacking truck ▪ forklift truckAll connectors and anchoring components can be stored neatly in this box and the boxes can be stacked.The Bolt-on caster set B turns the stacking pallet into a fast and manoeuvrable transport trolley.

Doka accessory boxes as storage units


Doka accessory box as transport devices

Lifting by crane



Bolt-on castor set B

The Bolt-on caster set B turns the stacking pallet into a fast and manoeuvrable transport trolley.Suitable for drive-through access openings > 90 cm.

The Bolt-on caster set B can be mounted to the follow-ing multi-trip packaging items: ▪ Doka accessory box ▪ Doka stacking pallets

Follow the directions in the 'Bolt-on castor set B' Operating Instructions!

Max. load-bearing capacity: 1000 kgPermitted imposed load: 5530 kg


▪ The rating plate must be in place and clearly legible.



☞ ▪ How to use with bolt-on castor set: Always apply the fixing brake when the con-tainer is 'parked'.When Doka accessory boxes are stacked, the bottom box must NOT be one with a bolt-on castor set mounted to it.



▪ When lifting stacking pallets to which Bolt-on castor sets B have been attached, you must also follow the directions in these Operating Instructions!


Follow the directions in the Operating Instruc-tions!

92816-206-01

Article n°[kg] Article n°[kg]

69999725002 - 02/2017

User Information Folding platform K Component overview

Component overview[kg]Article n°

Doka folding platform K 3.00m 291.5 580442000Doka folding platform K 4.50m 444.5 580443000Doka-Faltbühne K

Folding bracket K 52.4 580441000Faltkonsole K

Bow head K-ES 3.9 580444000Bügelkopf K-ES

Doka folding platform K outside corner 442.0 580424000Doka-Faltbühne K Außenecke

Doka folding platform K inside corner 283.0 580413000Doka-Faltbühne K Innenecke

Closure platform 3.00m 153.5 580485000Ausgleichsbühne 3,00m

Suspended platform 120 3.30m 44.0 580411000Suspended platform 120 4.30m 52.6 580412000Hängebühne 120

Support girder 28.5 580414000Stützträger

Bearing profile 4.9 580417000Druckprofil

Strut 32.9 580416000Stützstab

Horizontal brace d2 175 2.7 582733000Horizontalstrebe d2 175

Horizontal strut 1.35m 2.1 580422000Horizontale 1,35m

Timber parts varnished yellowSteel parts galvanisedDelivery condition: folded closed

GalvanisedLength: 224 cmHeight: 245 cmDelivery condition: folded closed

GalvanisedHeight: 35 cm

Timber parts varnished yellowSteel parts galvanisedWidth: 287 cmHeight: 245 cmDelivery condition: folded closed

Timber parts varnished yellowSteel parts galvanisedWidth: 294 cmHeight: 245 cmDelivery condition: folded closed

Timber parts varnished yellowSteel parts galvanisedDelivery condition: folded closed

GalvanisedDelivery condition: folded closed


GalvanisedLength: 34 cmWidth: 19 cm

GalvanisedLength: 370 cm

Galvanised

Galvanised


70 999725002 - 02/2017

Component overview User Information Folding platform K

Scaffold tube 48.3mm 0.50m 1.7 682026000Scaffold tube 48.3mm 1.00m 3.6 682014000Scaffold tube 48.3mm 1.50m 5.4 682015000Scaffold tube 48.3mm 2.00m 7.2 682016000Scaffold tube 48.3mm 2.50m 9.0 682017000Scaffold tube 48.3mm 3.00m 10.8 682018000Scaffold tube 48.3mm 3.50m 12.6 682019000Scaffold tube 48.3mm 4.00m 14.4 682021000Scaffold tube 48.3mm 4.50m 16.2 682022000Scaffold tube 48.3mm 5.00m 18.0 682023000Scaffold tube 48.3mm 5.50m 19.8 682024000Scaffold tube 48.3mm 6.00m 21.6 682025000Scaffold tube 48.3mm .....m 3.6 682001000Gerüstrohr 48,3mm

Screw-on coupler 48mm 50 0.84 682002000Anschraubkupplung 48mm 50

Swivel coupler 48mm 1.5 582560000Drehkupplung 48mm

Multi-purpose waling WS10 Top50 3.50m 68.4 580012000Mehrzweckriegel WS10 Top50 3,50m

Steel waling WS10 Top50 3.50m 71.5 580050000Stahlwandriegel WS10 Top50 3,50m

Facade precast member clamp V 8.1 580694000Fassaden-Fertigteilklemme V

Handrail extension K 4.9 580447000Geländerverlängerung K

Handrail post XP 1.20m 4.1 586460000Geländersteher XP 1,20m

Toeboard holder XP 1.20m 0.64 586461000Fußwehrhalter XP 1,20m

Railing clamp XP 40cm 7.7 586456000Geländerzwinge XP 40cm

Handrail clamp S 11.5 580470000Schutzgeländerzwinge S

Handrail clamp T 12.3 584381000Schutzgeländerzwinge T

Handrail post 1.10m 5.5 584384000Schutzgeländer 1,10m

Galvanised

GalvanisedWidth-across: 22 mmFollow fitting instructions!

GalvanisedWidth-across: 22 mmFollow fitting instructions!

Painted blue

Painted blue

GalvanisedLength: 70 cmHeight: 41 cmWidth-across: 50 mm





GalvanisedHeight: 123 - 171 cm

GalvanisedHeight: 122 - 155 cm



71999725002 - 02/2017


Attachable sleeve 24mm 0.03 584385000Steckhülse 24mm

Screw sleeve 20.0 0.03 584386000Schraubhülse 20,0

Side handrail clamping unit T 29.1 580488000Seitenschutzgeländer T

Universal railing shackle 3.0 580478000Universal-Geländerbügel

Doka 4-part chain 3.20m 15.0 588620000Doka-Vierstrangkette 3,20m

Transport fork K/M plus 226.0 583025000Umsetzgabel K/M plus

Platform transport fork K/M 194.0 580492000Bühnen-Umsetzgabel K/M

Star screw 0.75 580425000Sternschraube

Suspension plate AK 8.3 580494000Aufhängeblech AK

Suspension loop ES 1.0 580458000Einhängeschlaufe ES

Suspension profile AK 14.8 580595000Aufhängeprofil AK

Suspension profile ES 15.3 580596000Aufhängeprofil ES

Suspension plate ES 9.2 580493000Aufhängeblech ES

Quick-locking strap 55cm 0.07 580787000Gurtschnellverschluss 55cm

GreyLength: 16.5 cmDiameter: 2.7 cm

YellowLength: 20 cmDiameter: 3.1 cm

GalvanisedLength: 115 - 175 cmHeight: 112 cm


Follow the directions in the "Opera-ting Instructions"!

GalvanisedLength: 305 cmWidth: 204 cm

Painted blueLength: 205 - 262 cmWidth: 210 cmDelivery condition: folded closedFollow the directions in the "Opera-ting Instructions"!



Non-treatedLength: 72 cm




Yellow


72 999725002 - 02/2017


Universal tool box 15.0 9.1 580392000Universal-Werkzeugbox 15,0included in scope of supply:(A) Reversible ratchet 1/2" 0.73 580580000


(B) Fork wrench 13/17 0.08 580577000(C) Fork wrench 22/24 0.22 580587000(D) Fork wrench 30/32 0.80 580897000(E) Fork wrench 36/41 1.0 580586000(F) Ring spanner 17/19 0.27 580590000(G) Square nut 22 0.31 580589000(H) Box spanner 41 0.99 580585000(I) Extension 11cm 1/2" 0.20 580581000(J) Extension 22cm 1/2" 0.31 580582000(K) Universal joint coupling 1/2" 0.16 580583000(L) Box nut 19 1/2" L 0.16 580598000(M) Box nut 13 1/2" 0.06 580576000(N) Box nut 24 1/2" 0.12 580584000(O) Box nut 30 1/2" 0.20 580575000(P) Positioning cone spanner 15.0 DK 0.30 580579000

GalvanisedLength: 8 cmWidth-across: 30 mm

Ladder system XS

Connector XS Wall formwork 20.8 588662000Anschluss XS Wandschalung

Connector XS DM/SL-1 11.7 588672000Anschluss XS DM/SL-1

System ladder XS 4.40m 33.2 588640000System-Leiter XS 4,40m

Ladder extension XS 2.30m 19.1 588641000Leiternverlängerung XS 2,30m

Securing barrier XS 4.9 588669000Sicherungsschranke XS

Ladder cage XS 1.00m 16.5 588643000Ladder cage XS 0.25m 10.5 588670000Rückenschutz XS

Ladder cage exit XS 17.0 588666000Rückenschutz-Ausstieg XS

GalvanisedWidth: 89 cmHeight: 63 cm


Galvanised

Galvanised


Galvanised



73999725002 - 02/2017


Tie rod system 15.0

Suspension cone 15.0 5cm 0.88 581971000Aufhängekonus 15,0 5cm

Cantilever positioning cone 15.0 5cm 0.45 581699000Sperrenvorlauf 15,0 5cm

Fair-faced concrete positioning cone 15.0 5cm 0.46 581973000Sichtbetonvorlauf 15,0 5cm

Sealing sleeve 15.0 5cm 0.008 581990000Dichtungshülse 15,0 5cm

Sealing sleeve S 15.0 5cm 0.009 581697000Dichtungshülse S 15,0 5cm

Fair-faced concrete plug 41mm plastic 0.007 581851000Fair-faced concrete plug 41mm concrete 0.05 581848000Sichtbetonstopfen

Fixing plate 15.0 0.15 581692000Nagelblech 15,0

Suspension cone 15.0 f. insulation up to 11cm 3.6 580495000Aufhängekonus 15,0 für Isolierung bis 11cm

Sealing sleeve 15.0 f. insulation up to 11cm 0.05 580498000Dichtungshülse 15,0 für Isolierung bis 11cm

Positioning disk Rd28 0.25 580497000Vorlaufscheibe Rd28

Cone screw Rd28 0.65 580496000Konusschraube Rd28

Tie rod 15.0mm galvanised 0.50m 0.72 581821000Tie rod 15.0mm galvanised 0.75m 1.1 581822000Tie rod 15.0mm galvanised 1.00m 1.4 581823000Tie rod 15.0mm galvanised 1.25m 1.8 581826000Tie rod 15.0mm galvanised 1.50m 2.2 581827000Tie rod 15.0mm galvanised 1.75m 2.5 581828000Tie rod 15.0mm galvanised 2.00m 2.9 581829000Tie rod 15.0mm galvanised 2.50m 3.6 581852000Tie rod 15.0mm galvanised .....m 1.4 581824000Tie rod 15.0mm non-treated 0.50m 0.73 581870000Tie rod 15.0mm non-treated 0.75m 1.1 581871000Tie rod 15.0mm non-treated 1.00m 1.4 581874000Tie rod 15.0mm non-treated 1.25m 1.8 581886000Tie rod 15.0mm non-treated 1.50m 2.1 581876000Tie rod 15.0mm non-treated 1.75m 2.5 581887000Tie rod 15.0mm non-treated 2.00m 2.9 581875000Tie rod 15.0mm non-treated 2.50m 3.6 581877000Tie rod 15.0mm non-treated 3.00m 4.3 581878000Tie rod 15.0mm non-treated 3.50m 5.0 581888000Tie rod 15.0mm non-treated 4.00m 5.7 581879000Tie rod 15.0mm non-treated 5.00m 7.2 581880000Tie rod 15.0mm non-treated 6.00m 8.6 581881000Tie rod 15.0mm non-treated 7.50m 10.7 581882000Tie rod 15.0mm non-treated .....m 1.4 581873000Ankerstab 15,0mm

Super plate 15.0 1.1 581966000Superplatte 15,0

Stop anchor 15.0 16cm 55 0.38 581997000Sperranker 15,0 16cm 55

Pigtail anchor 15.0 0.92 581984000Wellenanker 15,0

Suspension cone 15.0 with collar 1.4 580428000Bund-Aufhängekonus 15,0

Rock anchor spreader unit 15.0 0.41 581120000Felsanker-Spreizeinheit 15,0

GalvanisedLength: 16 cmDiameter: 6 cmFollow fitting instructions!

Length: 11 cmDiameter: 5 cmTool: Positioning cone spanner 15.0 DKFollow fitting instructions!

GalvanisedLength: 11 cmDiameter: 4.3 cmTool: Positioning cone spanner 15.0 DK

OrangeLength: 10 cmDiameter: 3 cm

OrangeLength: 11 cmDiameter: 4.7 cm

Grey

GalvanisedDiameter: 10 cm

GalvanisedLength: 30 cmDiameter: 5 cm

WhiteLength: 30 cmDiameter: 6 cm

GalvanisedDiameter: 9 cm


GalvanisedHeight: 6 cmDiameter: 12 cmWidth-across: 27 mm

Non-treated

Non-treatedLength: 67 cm




74 999725002 - 02/2017


Rock anchor installation tube 0.85 581123000Felsanker-Einbaurohr

Tensioning instrument B 34.5 580570000Vorspanngerät B

Screw-in cone 15.0 0.74 581895000Einschraubkonus 15,0

Bridge edge beam anchor 15.0 0.45 581896000Bridge edge beam anchor 15.0 galv. 0.44 581890000Gesimsanker 15,0

Nailing cone 15.0 0.02 581897000Nagelkonus 15,0

Hole plug 29mm 0.003 581891000Gesimsankerstopfen 29mm

Zinc plug 15.0 0.20 581889000Zinkstöpsel 15,0

Protective cap 15.0/20.0 0.03 581858000Schutzkappe 15,0/20,0

Tie-rod wrench 15.0/20.0 1.9 580594000Ankerstabschlüssel 15,0/20,0

Positioning cone spanner 15.0 DK 0.30 580579000Vorlaufschlüssel 15,0 DK

Universal cone spanner 15.0/20.0 0.90 581448000Universal-Konusschlüssel 15,0/20,0

Multi-trip packaging

Doka skeleton transport box 1.70x0.80m 87.0 583012000Doka-Gitterbox 1,70x0,80m

Doka multi-trip transport box 1.20x0.80m 70.0 583011000Doka-Mehrwegcontainer 1,20x0,80m

Multi-trip transport box partition 0.80m 3.7 583018000Multi-trip transport box partition 1.20m 5.5 583017000Mehrwegcontainer Unterteilung

Doka stacking pallet 1.55x0.85m 41.0 586151000Doka-Stapelpalette 1,55x0,85m

Doka stacking pallet 1.20x0.80m 38.0 583016000Doka-Stapelpalette 1,20x0,80m

Doka accessory box 106.4 583010000Doka-Kleinteilebox


Galvanised


Length: 7 cmFollow fitting instructions!

BlackLength: 7 cm

GreyDiameter: 3 cm

GalvanisedLength: 9.9 cmDiameter: 2.9 cmTool: Spanner for 1/2" square head

YellowLength: 6 cmDiameter: 6.7 cm






Timber parts varnished yellowSteel parts galvanised



Timber parts varnished yellowSteel parts galvanisedLength: 154 cmWidth: 83 cmHeight: 77 cm


75999725002 - 02/2017


Bolt-on castor set B 33.6 586168000Anklemm-Radsatz B

Painted blue

999725002 - 02/2017Doka GmbH | Josef Umdasch Platz 1 | 3300 Amstetten | Austria | T +43 7472 605-0 | F +43 7472 66430 | [email protected] | www.doka.com

Near to you, worldwide

Doka is one of the world leaders in developing, manu-facturing and distributing formwork technology for use in all fields of the construction sector.With more than 160 sales and logistics facilities in over 70 countries, the Doka Group has a highly efficient dis-tribution network which ensures that equipment and

technical support are provided swiftly and profession-ally.An enterprise forming part of the Umdasch Group, the Doka Group employs a worldwide workforce of more than 6000.

www.doka.com/folding-platform-k

Documents

The Formwork Experts. Folding platform K - Doka · PDF fileThe Formwork Experts. Folding platform K User Information Instructions for assembly and use (Method statement) ... Do not