The Articulator 2961AGC/2973AGC Parts Manual

The Articulator

2961AGC/2973AGC

Parts ManualManual Part #: Man-2961AGC

LASTEC7865 N County Road 100E

Lizton, Indiana 46149

Phone (317) 892-4444 Fax (317) 892-4188 www.lastec.com

8 Lastec, 2008

Printed in the United States of America, all rights reserved. No part of this manual may be reproduced in any form by any photographic, electronic, mechanical or other means or used in any information storage and retrieval system without written permission from

Lastec, Inc.7865 N. County Road 100E

Lizton, IN 46149

Table of Contents Section-Page

SECTION 1 GENERAL INFORMATION 1-1

1.1 How To Use The Parts List ....................................................................................... 1-21.2 Torque Values ........................................................................................................... 1-31.3 Decals ........................................................................................................................ 1-41.4 Hardware Kit (CE Only) ........................................................................................... 1-9

SECTION 2 DRIVE SYSTEM 2-1

2.1 Seat Assembly .......................................................................................................... 2-22.2 Roll-Over Protection System (ROPS) ....................................................................... 2-42.3 Rocker Assembly (Serial # 2130406 and prior) ........................................................ 2-62.4 Rocker Assembly, 61” Deck (Serial # 2140406 and later) ....................................... 2-82.5 Rocker Assembly, 73” Deck ................................................................................... 2-102.6 Left Rocker Deck Lift Assembly, 61” Deck (Prior to Serial #54410615) .............. 2-122.7 Right Rocker Deck Lift Assembly, 61” and 73” Decks (Prior to Serial #54410615)2-142.8 Left Rocker Deck Lift Assembly, 73” Deck (Prior to Serial #54410615) .............. 2-162.9 Rocker Wheel Assembly ......................................................................................... 2-182.10 Wheel Yoke Assembly ............................................................................................ 2-202.11 Wheel Assembly, 13 x 6.50 x 6............................................................................... 2-222.12 Hand Contol Assembly............................................................................................ 2-242.13 Control Box Assembly ............................................................................................ 2-262.14 Pedal Assembly (Optional as of serial #26270307) ................................................ 2-282.15 Throttle Assembly (Deleted after Serial # 24321106) ............................................ 2-302.16 Front Deck Lift Rod Assembly (Serial #24311106 and prior)................................ 2-322.17 Front Deck Lift Rod Assembly (Serial #24331106 and later) ................................ 2-342.18 Emergency Brake Assembly ................................................................................... 2-362.19 Rear Deck Lift Rod Assembly ................................................................................ 2-382.20 Framework............................................................................................................... 2-402.21 Pull Bar Assembly................................................................................................... 2-422.22 Roller Assembly Upgrade Kit (Optional)................................................................ 2-442.23 Striping Kit (Optional) ............................................................................................ 2-46

SECTION 3 HYDRAULIC SYSTEM 3-1

3.1 Hydraulic Layout Diagram (Serial #46570113 and later) ......................................... 3-23.2 Hydraulic Layout Diagram (Prior to Serial #46570113)........................................... 3-43.3 Hydraulic Pump Assemblies ..................................................................................... 3-63.4 Hydraulic Motor, Right ............................................................................................. 3-83.5 Hydraulic Motor, Left ............................................................................................. 3-103.6 Brake Assembly....................................................................................................... 3-123.7 Hydraulic Tank Assembly (Serial #46570113 and later) ........................................ 3-143.8 Hydraulic Tank Assembly (Priot to Serial #46570113) .......................................... 3-163.9 Hydraulic Drive Idler Assembly ............................................................................. 3-18

3 Lastec//072815 Table of Contents


SECTION 4 ENGINE & ELECTRICAL 4-1

4.1 Fuel Tank Assembly (Serial #46570113 and later)................................................... 4-24.2 Fuel Tank Assembly (Serial #25620207 to #46560113)........................................... 4-44.3 Fuel System ............................................................................................................... 4-64.4 Engine Guard Assembly............................................................................................ 4-84.5 Engine Assembly..................................................................................................... 4-104.6 Radiator Cowling Assembly.................................................................................... 4-124.7 Motor Mount and Hardware.................................................................................... 4-144.8 Deck Drive Idler Assembly ..................................................................................... 4-164.9 Air Filter Assembly ................................................................................................. 4-184.10 Battery Tray Assembly............................................................................................ 4-204.11 Wiring Harness ....................................................................................................... 4-22

SECTION 5 61” MOWER DECK 5-1

5.1 Deck Framework ....................................................................................................... 5-25.2 Deck 1 Hardware (Serial # 2860806 and later) ......................................................... 5-45.3 Deck 1 Hardware (Serial # 2850806 and prior) ........................................................ 5-65.4 Deck 2 Hardware....................................................................................................... 5-85.5 Deck 3 Hardware..................................................................................................... 5-105.6 Rear Discharge Baffle Assembly ............................................................................ 5-125.7 Optional Mulching Kit ............................................................................................ 5-145.8 Double Pulley Spindle (5/14 and later) ................................................................... 5-165.9 Spindle Housing ..................................................................................................... 5-185.10 Double Pulley Spindle (Prior to 5/14) ..................................................................... 5-205.11 Spindle Housing ...................................................................................................... 5-225.12 Tensioner Assembly ................................................................................................ 5-245.13 Grass Chute ............................................................................................................. 5-265.14 Rear Anti-scalp Roller (Prior to 5/14) ..................................................................... 5-28

SECTION 6 73” MOWER DECK 6-1

6.1 Deck Framework ....................................................................................................... 6-26.2 Deck 1 Hardware....................................................................................................... 6-46.3 Deck 2 Hardware....................................................................................................... 6-66.4 Deck 3 Hardware....................................................................................................... 6-86.5 Double Pulley Spindle, Decks 1 and 3 (8/14 and later) ......................................... 6-106.6 Spindle Housing, Decks 1 and 3 (8/14 and later) .................................................... 6-126.7 Double Pulley Spindle, Decks 1 and 3 (Prior to 8/14) ............................................ 6-146.8 Spindle Housing ...................................................................................................... 6-166.9 Tensioner Assembly ................................................................................................ 6-186.10 Deck 2, Double Pulley Drive Spindle (8/14 and later)............................................ 6-206.11 Deck 2, Double Pulley Drive Spindle (Prior to 8/14) ............................................. 6-226.12 Grass Chute ............................................................................................................. 6-246.13 Rear Anti-scalp Roller (Prior to 8/14) ..................................................................... 6-26

Table of Contents Lastec//072815 4


SECTION 7 INDEX 7-1

Table of Contents Lastec//072815 5

Mower//072815 1-1

1

SECTION 1 GENERAL INFORMATION

General InformationHow To Use The Parts List

General Information Mower//072815 1-2

1

1.1 How To Use The Parts List

Use the table of contents or part number index to locate the part you need.

Go to the appropriate section and locate the part in the table and illustration.

Parts shown indented under another part are included with that part. IMPORTANT:Assemblies marked with a diamond () are non-saleable and all the parts shown as included need to be purchased separately.

See the sample table below. Sample Assembly A01111 includes part F02222-22 and sub-assembly A03333. The diamond () indicates that assembly A01111 is non-saleable and all the parts shown as included need to be purchased separately. Subassembly A03333 includes parts S04444-4 and F07777-77. The diamond () indicates that subassembly A03333 is non-saleable and all the parts shown as included need to be purchased sepa-rately.

To Order Parts:

From the continental U.S., call your local Lastec distributor to order parts. If there is no Lastec distributor in your area, call 1-800-515-6798. Have your customer num-ber, unit serial number, and part numbers ready when you call.

From other international locations, contact the Lastec distributor in your area for parts.

REF PART # DESCRIPTION (Indicates Non-Saleable Items) COMMENTS QTY.

A01111 Sample Assembly 1

1 F02222-22 Sample Part 1

A03333 Sample Subassembly 1

2 S04444-4 Sample Part 1

3 F07777-77 Sample Part 1

General InformationTorque Values1

1-3 Mower//072815 General Information

1.2 Torque Values

Below is a table of suggested torque values for this unit. Please use these torque values

on this unit unless otherwise specified.

Grade Units SAE 5 SAE 8

Tensile

Strength

105000

PSI150000

PSI

Grade Mark

Bolt

Dia.

Threads.

Per In.Units SAE 5 SAE 8

6

8

10

10

12

1/4

1/4

5/16

5/16

3/8

3/8

7/16

7/16

1/2

1/2

9/16

9/16

5/8

5/8

3/4

3/4

7/8

7/8

1

32

32

24

32

24

20

28

18

24

16

24

14

20

13

20

12

18

11

18

10

16

9

14

8

in-lbs (Nm)

in-lbs (Nm)

in-lbs (Nm)

in-lbs (Nm)

in-lbs (Nm)

in-lbs (Nm)

in-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

ft-lbs (Nm)

20 (2.3)

24 (2.7)

35 (4.0)

40 (4.5)

50 (5.7)

95 (10.7)

95 (10.7)

17 (22.6)

20 (27.1)

30 (40.7)

35 (47.5)

50 (67.8)

55 (74.6)

75 (101.7)

85 (115.3)

105 (142.4)

115 (155.9)

150 (203.4)

160 (217.0)

170 (230.5)

175 (237.3)

302 (409.5)

300 (406.8)

466 (631.8)

-

30 (3.4)

45 (5.1)

50 (5.7)

65 (7.3)

125 (14.1)

150 (17.0)

23 (31.2)

25 (33.8)

40 (54.2)

45 (61.0)

65 (88.1)

70 (94.9)

100 (135.6)

110 (149.2)

135 (183.1)

150 (203.4)

195 (264.4)

210 (284.8)

220 (298.3)

225 (305.1)

473 (640.9)

400 (542.4)

714 (967.4)

General InformationDecals 1

1.3 Decals

Decals (US Only)

REF PART # DESCRIPTION COMMENTS QTY.

055843 Decal Kit, 2961AGC 61” Deck Only 1


1 049747 Decal, Comm Mower Control Panel Gas 1

2 028601 Decal, Fwd/Rev Motion 2

3 049930 Decal, Belt Routing Diagram 1

4 048227 Decal, Hydro Fill Line 1

5 019554 Decal, Warning, Operational Safety 425D 1

6 040911 Decal, Warning Operate With Guards 2

7 056591 Decal, 18 PSI 2

8 014419 Decal, Hot Engine Warning 1

9 042003 Decal, Warning, Slope 1

10 062404 Decal, AGC/ADC Hydro 1

11 040912 Decal, Danger, Thrown Objects/Arrow 1

12 045519 Decal, Sound Power Level 1

062425 Decal, Relays for 055700-055846 Not Shown 1

019552 Decal, Caution Clean Radiator Not Shown 1

13 041200 Decal, Fuel Switch 421D 1

14 044731 Decal, Control Box Engine Throttle 1

15 049466 Decal, Comm. Deck Height Adjustment 1

16 028603 Decal, Brake Control 1

17 043225 Decal, Flat World Logo 1

18 P478 Decal, Danger - Rotating Blades 2

19 062429 Decal, Lastec Made in USA 1

20 040910 Decal, Warning Operate From Seat 2

21 048504 Decal, Lastec, Roll Bar 1

22 019557 Decal, Articulator Logo Div WM 1

23 049619 Decal, 2961AGC Articulatot Large 61” Deck Only 2

049620 Decal, 2973AGC Articulator Large 73” Deck Only 2

24 049931 Decal, 61 Inches 61” Deck Only 2

049465 Decal, 73 Inches 73” Deck Only 2

P485 Decal, Fuel Equipment 325E Not Shown 2

General Information Lastec//072815 1-4

General InformationDecals1

WARNING

042003

Fuel Control Valve

OffRig

ht

Tank

Left Tank

WARNING

Without all safety shields and guards in place

at all times.

AVOID SERIOUS INJURY OR DEATH

040911

Burn Hazard

Avoid contact with any part of hot engine.

Failure to do so may result in serious injury.

Wood-Mizer Products, Inc.800-525-8100 Reorder #014419

DANGER THROWN OBJECTS

Before mowing clear area of people and objects which

may be thrown by blades.

ROTATING BLADES Do not put hands or feet under

or into mower when engine is running. 040912

WARNING


at all times.


040911

WARNING Operate from operator

seat only. Follow all safety rules in

owner manual during operation or maintenance.


040910

Fill Line

048227

Belt Routing 049930

Fill Tire to:

18 psi056591

Fill

Tire

to:

18 p

si

0565

91

This unit uses hydraulic fluid

Hydraulic Filter

(uses 2 filters/mower)

Hydraulic Fluid (1qt)

2.5 gal Service Kit (includes 2 filters)


ITEM PART #

P620

040642

049929

049928

062404

Under Seat PanOn Hydraulic Tank

LT0126

OROR

Center of Rear Bumper

73” 73”

1-5 Lastec//072815 General Information


Decals (CE Only)





2 028601 Decal, Fwd/Rev Motion 2

3 049930 Decal, Belt Routing Diagram 1

4 048227 Decal, Hydro Fill Line 1

5 019554 Decal, Warning, Operational Safety 425D 1

6 040911 Decal, Warning Operate With Guards 2

7 056591 Decal, 18 PSI 2

8 014419 Decal, Hot Engine Warning 1

9 042003 Decal, Warning, Slope 1

10 062404 Decal, AGC/ADC Hydro 1

11 040912 Decal, Danger, Thrown Objects/Arrow 1

12 045519 Decal, Sound Power Level 1

062425 Decal, Relays for 055700-055846 Not Shown 1

019552 Decal, Caution Clean Radiator Not Shown 1

13 041200 Decal, Fuel Switch 421D 1

14 044731 Decal, Control Box Engine Throttle 1

15 049466 Decal, Comm. Deck Height Adjustment 1

16 028603 Decal, Brake Control 1

17 043225 Decal, Flat World Logo 1

18 P478 Decal, Danger - Rotating Blades 2

19 062429 Decal, Lastec Made in USA 1

20 040910 Decal, Warning Operate From Seat 2

21 048504 Decal, Lastec, Roll Bar 1

22 019557 Decal, Articulator Logo Div WM 1

23 049619 Decal, 2961AGC Articulatot Large 61” Deck Only 2

049620 Decal, 2973AGC Articulator Large 73” Deck Only 2

24 049931 Decal, 61 Inches 61” Deck Only 2

049465 Decal, 73 Inches 73” Deck Only 2

P485 Decal, Fuel Equipment 325E Not Shown 2

067065 Decal Kit, CE Deck 1

040267 Decal Kit, European Languages 2

040256 Decal, Warning, Outer Decks -- German 1

040257 Decal, Warning, Outer Decks -- French 1

040258 Decal, Warning, Outer Decks -- Italian 1

040259 Decal, Warning, Outer Decks -- Spanish 1

040260 Decal, Warning, Outer Decks -- Danish 1

P117 Decal, Hands & Feet 7


General InformationDecals1

041205 Decal, Thrown Objects CE Std 1

041206 Decal, Caution Symbol CE Std 2

041209 Decal, Keep Away/Rotating Drive Line CE 2

WARNING

042003

Fuel Control Valve

OffRig

ht

Tank

Left Tank

WARNING


at all times.


040911

Burn Hazard

Avoid contact with any part of hot engine.

Failure to do so may result in serious injury.

Wood-Mizer Products, Inc.800-525-8100 Reorder #014419

DANGER THROWN OBJECTS

Before mowing clear area of people and objects which

may be thrown by blades.

ROTATING BLADES Do not put hands or feet under

or into mower when engine is running. 040912

WARNING


at all times.


040911

WARNING Operate from operator

seat only. Follow all safety rules in

owner manual during operation or maintenance.


040910

Fill Line

048227

Belt Routing 049930

Fill Tire to:

18 psi056591

Fill

Tire

to:

18

psi 05

659

1

This unit uses hydraulic fluid

Hydraulic Filter

(uses 2 filters/mower)

Hydraulic Fluid (1qt)



ITEM PART #

P620

040642

049929

049928

062404

Under Seat PanOn Hydraulic Tank

LT0128

OROR

Center of Rear Bumper

73” 73”

04120

04120

04120

CE

1-7 Lastec//072815 General Information



Mower DecksHardware Kit (CE Only)1

1.4 Hardware Kit (CE Only)

Hood Assembly, 29HP Kawasaki CE

Nut Assembly, 3/8-16 Cover Retaining

Rivet, 3/16” Dia x 3/8-1/2” Grip Range Pop

Instruction Sheet, 2961/73 CE Hardware Kit


064521 Kit, 2961/73 CE Hardware 1

1 064468 1

2 064500 6

3 F04203-6 6

IS-0307 1

1-9 Lastec//072815 Mower Decks

Mower DecksHardware Kit (CE Only) 1

290009

Mower Decks Lastec//072815 1-10

Mower//072815 2-1

2

SECTION 2 DRIVE SYSTEM

Drive SystemSeat Assembly2

2.1 Seat Assembly

Seat, Air Ride (Color Gray)

Switch, Seat

Screw, Seat Switch

Seat Belt, 2” ALR/ERI Buckle

Pan Weldment, Seat

Bolt, 3/8-16 x 4 1/2” Hex Head 316 SS

Nut, 3/8-16 Hex Half Nylon Lock 316 SS

Nut, 5/16-18 Nylok Hex

Clamp, 1/4" Wire 13/32” Mtg Hole

Bolt, 5/16-18 x 3/4” Hex Head Grade 5

Bolt, 5/16-18 x 1” Hex Head Grade 5

Washer, 5/16” x 1 1/4” Fender

Cable, Seat Lanyard

Spring, Extension 3/8” x 3”


049590 Seat Assembly, Complete Gas 1

1 P630 1

2 P826 1

3 F412 2

P776 Sold as a pair 1

4 049589 1

5 F05007-244 2

6 F05010-234 2

7 F05010-58 3 Added after Serial # 19403061 Added after Serial # 2960906

7

8 024155 Added after Serial # 2960906 1

9 F05006-102 Added after Serial # 2960906 1

10 F05006-27 3 Added after Serial # 1940306 5

11 F05011-50 3 Added after Serial # 1940306 4

12 045988 Added after Serial # 1940306 2

13 014818 1

052025 Seat Delay Assembly, LasTec Mowers Not Shown 1

2-2 Lastec//072815 Drive System

Drive SystemSeat Assembly 2

LT0064

Drive System Lastec//072815 2-3

Drive SystemRoll-Over Protection System (ROPS)2

2.2 Roll-Over Protection System (ROPS)

Frame Weldment, ROPS

Frame Weldment, Comm. ROPS Lower

Frame Weldment, Comm. ROPS Lower

Knob w/Stud, 3/8-16 x 1.50”

Nut, 3/8-16 Hex Nyloc

Pull Pin, 1/2”


Washer, 1.50” OD x .53” ID UHMW

Nut, 1/2-13 Nylon Hex Lock


Washer, 3/8” Flat SAE

Bolt, 3/8-16 x 2 3/4” Hex Head Grade 5


049796 ROPS Assembly, 2861 Folding 1

1 049831 1

1 ROPS framing members may not be sold separately. When ordering, you will receive all three frame weldments (049831, 049736 and 049736-1).

1

2 0497361 1

3 049736-11 1

4 049447 2

5 F05010-10 10

6 049448 2

7 F05008-23 2

8 049446 4

9 F05010-8 2

10 F05007-126 4

11 F05011-3 4

12 F05007-206 4


Drive SystemRoll-Over Protection System (ROPS) 2

LT0065


Drive SystemRocker Assembly (Serial # 2130406 and prior)2

2.3 Rocker Assembly (Serial # 2130406 and prior)

NOTE: Left and right Rockers are mirror images of each other. Be sure to order the cor-rect weldment or cover for the side needed. (Left side shown in illustration.)


1 F05005-79 Bolt, 1/4-20 x 1/2” Hex Head Cap 4

2 F05011-14 Washer, 1/4” Split Lock 4

3 F05011-11 Washer, 1/4” SAE Flat 4

4 049791 Cover, Left Rocker 1

049792 Cover, Right Rocker 1

5 F05009-10 Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 1

6 F05008-106 Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5 1

7 F05010-185 Nut, 5/8-11 Flexloc 3

8 F05010-8 Nut, 1/2-13 Nyl Hex Lock 1 added after serial # 1660206 4

9 F05008-23 Bolt, 1/2-13 x 3” Hex Head Grade 5 Zinc 2

10 F05009-37 Bolt, 5/8-11 X 3” Hex Head Grade 5 Zinc 2

11 049710 Rocker Weldment, Left 61” deck 1

049717 Rocker Weldment, Right 1

11 055384 Rocker Weldment, 73” Right 73” Deck 1

055385 Rocker Weldment, 73” Left 1

12 P107 Fitting, 1/4-28 Straight Grease 1

13 049893 Washer, 3 1/2” OD Wave 1

14 048173 Washer, Wheel Damper 1

15 048174 Block, Wheel Yoke Friction 1

16 F05011-5 Washer, 5/8” SAE Flat Added after serial # 1660206 2

17 F05008-35 Bolt, 1/2-13 x 4-1/2” Hex Head Gr5 1

18 043285 Spring, .72” x 2.75” x .105” MW Added after serial # 1660206 1

19 F05010-8 Nut, 1/2-13 Nyl Hex Lock Added after serial # 1660206 1


Drive SystemRocker Assembly (Serial # 2130406 and prior) 2

049715


Drive SystemRocker Assembly, 61” Deck (Serial # 2140406 and later)2

2.4 Rocker Assembly, 61” Deck (Serial # 2140406 and later)


Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade 5

Nut, 5/8-11 FlexLoc

Nut, 1/2-13 Nyl Hex Lock


Bolt, 5/8-11 x 3 Hex Head Grade 5

Rocker Weldment, Right

Rocker Weldment, Left

Rocker Weldment, Left

Cap, Hub

Fitting, 1/4-28 Straight Grease

Seal, 1 1/4” ID Trb Bearing

Washer, 3-1/2” OD Wave

Washer, Wheel Damper

Block, Wheel Yoke Friction

Wheel Yoke Assembly, 13” Comm Right

Wheel Yoke Assembly, 13” Comm

Washer, 5/8” SAE Flat



Spring, 0.72” x 2.75” x 0.105” MW

Nut, 1/2-13 Hi-Crown Acorn Cap Plated

Nut, 1/2-13 Nylon Hex Lock

Rocker Wheel Assembly, Right

Rocker Wheel Assembly, Left

Lift Assembly, Right Rocker Deck

Lift Assembly, Left Rocker Deck

NOTE: The left and right rocker assemblies are mirror images of each other. Be sure to order the correct rocker weldment, wheel yoke, rocker wheel and deck lift assemblies for the side needed. (Left side shown below.)


055086 Rocker Assembly, Right Right Side Only 1

055085 Rocker Assembly, Left Left Side Only 1

1 F05009-10 1

2 F05008-106 1

3 F05010-185 3

4 F05010-8 3

5 F05008-23 2

6 F05009-37 2

7 055084 Right Side Only 1

055486 Left Side Only. Serial #24441106 and later

1

055083 Left Side Only. Serial #2130406 to 24431106

1

8 P195 1

9 P107 1

10 P191 1

11 049893 1

12 048173 1

13 048174 1

14 049668 Right Side Only. See Section 2.10 1

046477 Left Side Only. See Section 2.10 1

15 F05011-5 2

16 F05008-106 1

1 Bolt, spring and nut reversed orientation after serial #2850806.

Serial #2850806 and later 1

F05008-35 Serial #2850806 and prior 1

17 043285 1

18 F05010-201 Serial #2850806 and later 1

F05010-8 Serial #2850806 and prior 1






Drive SystemRocker Assembly, 61” Deck (Serial # 2140406 and later) 2

LT0066


Drive SystemRocker Assembly, 73” Deck2

2.5 Rocker Assembly, 73” Deck

NOTE: The left and right rocker assemblies are mirror images of each other. Be sure to order the correct rocker weldment, wheel yoke, rocker wheel and deck lift assemblies for the side needed. (Left side shown below.)


055386 Rocker Assembly, 73” Right Right Side Only 1

055387 Rocker Assembly, 73” Left Left Side Only 1



3 F05010-185 Nut, 5/8-11 FlexLoc 3

4 F05010-8 Nut, 1/2-13 Nyl Hex Lock 3

5 F05008-23 Bolt, 1/2-13 x 3” Hex Head Grade 5 2

6 F05009-37 Bolt, 5/8-11 x 3 Hex Head Grade 5 2

7 055384 Rocker Weldment, Right Right Side Only 1

055385 Rocker Weldment, Left Left Side Only 1

8 P195 Cap, Hub 1


10 P191 Seal, 1 1/4” ID Trb Bearing 1

11 049893 Washer, 3-1/2” OD Wave 1

12 048173 Washer, Wheel Damper 1

13 048174 Block, Wheel Yoke Friction 1

14 049668 Wheel Yoke Assembly, 13” Comm Right Right Side Only. See Section 2.10 1

046477 Wheel Yoke Assembly, 13” Comm Left Side Only. See Section 2.10 1



17 043285 Spring, 0.72” x 2.75” x 0.105” MW 1

18 F05010-201 Nut, 1/2-13 Hi-Crown Acorn Cap Plated 1

19 049745 Rocker Wheel Assembly, Right Right Side Only. See Section 2.9 1

049740 Rocker Wheel Assembly, Left Left Side Only. See Section 2.9 1

20 049790 Lift Assembly, Right Rocker Deck Right Side Only. See Section 2.7 1

049726 Lift Assembly, Left Rocker Deck Left Side Only. See Section 2.8 1


Drive SystemRocker Assembly, 73” Deck 2

LT0059


Drive SystemLeft Rocker Deck Lift Assembly, 61” Deck (Prior to Serial #54410615)2

2.6 Left Rocker Deck Lift Assembly, 61” Deck (Prior to Serial #54410615)


Washer, 3/8” Suspension

Bushing, 3/8” Polyurethane Suspension

Spacer, 3/8” Suspension

Nut, 3/8-16 Hex Nyl Lock


055831 Lift Assembly, Left Rocker Deck 1


2 048712 Bushing, 1 1/16" Urethane Pivot 2

3 048692 Strap, 1U 2

4 F05011-3 Washer, 3/8” Flat SAE 4

5 F05010-10 Nut, 3/8-16 Hex Nyloc 4

6 055483 Lift Weldment, Left Deck 1



9 P829 Bushing, 1/2” ID x 3/4” OD x 1/2” Brnz 2


11 049725 Lift Weldment, Deck Tab 1

12 F05005-105 Screw, 1/4-28 x 1/4” BO Socket Head Pt Set 2

049843 Link Assembly, 3/8” Suspension 1

13 N/A Not sold separately 1




17 F05010-10 1


Drive SystemLeft Rocker Deck Lift Assembly, 61” Deck (Prior to Serial #54410615) 2

LT0060


Drive SystemRight Rocker Deck Lift Assembly, 61” and 73” Decks (Prior to Serial #54410615)2

2.7 Right Rocker Deck Lift Assembly, 61” and 73” Decks (Prior to Serial #54410615)







049790 Lift Assembly, Right Rocker Deck 1



3 048692 Strap, 1U 2


5 F05010-10 Nut, 3/8-16 Hex Nyloc 4

6 049789 Lift Weldment, Right Deck 1












17 F05010-10 1


Drive SystemRight Rocker Deck Lift Assembly, 61” and 73” Decks (Prior to Serial #54410615) 2

LT0063


Drive SystemLeft Rocker Deck Lift Assembly, 73” Deck (Prior to Serial #54410615)2

2.8 Left Rocker Deck Lift Assembly, 73” Deck (Prior to Serial #54410615)







049726 Lift Assembly, Left Rocker Deck 1



3 048692 Strap, 1U 2


5 F05010-10 Nut, 3/8-16 Hex Nyloc 4

6 049720 Lift Weldment, Left Deck 1












17 F05010-10 1


Drive SystemLeft Rocker Deck Lift Assembly, 73” Deck (Prior to Serial #54410615) 2

LT0060


Drive SystemRocker Wheel Assembly2

2.9 Rocker Wheel Assembly

NOTE: The left and right assemblies are mirror images of each other. Be sure to order the correct weldment for the side needed. (Left side shown below.)

CAUTION: Bolts holding urethane bushings must remain tight. Equipment damage may occur.


049745 Rocker Wheel Assembly, Right Right Side Only 1

049740 Rocker Wheel Assembly, Left Left Side Only 1

1 049870 Bushing, Urethane Pivot Apply water-proof axle grease to mating surfaces prior to assembly. Serial #1660206 and later

2

049510 Bushing, Rubber Pivot Serial #2780806 and prior.No longer available; order 049870

2

2 049744 Weldment, Right Rocker Wheel Pivot Right Side Only 1

049741 Weldment, Left Rocker Wheel Pivot Left Side Only 1

3 F05010-34 Nut, 5/8-11 Nyl Lock 1


5 027013 Wheel, Anti-Scalp 5-5/8" hole 1


Drive SystemRocker Wheel Assembly 2

LT0061


Drive SystemWheel Yoke Assembly2

2.10 Wheel Yoke Assembly


046477 Wheel Yoke Assembly, 13” Comm Left Side & Front Only 1

049668 Wheel Yoke Assembly, 13” Comm Right Right Side Only 1

1 P434 Nut, 3/4-16 Castle 1


3 P190 Bearing, 1” ID Tapered Roller 1

4 043968 Spacer, Wheel Yoke Bearing 2

5 F05012-79 Pin, 5/32” x 1 1/2” Cotter Serial # 2161105 and later 1

F05012-49 Pin, 1/8” x 1 1/2” Cotter Serial # 2151105 and prior 1

6 046478 Yoke Weldment, 2561 Front Wheel 1


8 F05010-177 Nut, 3/4-10 Stover Swaged 1

9 045986 Wheel Assembly, 13” x 6.5” x 6” See Section 2.11 1

10 P296 Spacer, 1.13” OD x .75” ID x .5” 2


Drive SystemWheel Yoke Assembly 2

LT0054

Valve StemThis Side

(Right SideAssembly Only)

Valve StemThis Side(Left SideAssembly Only)


Drive SystemWheel Assembly, 13 x 6.50 x 62

2.11 Wheel Assembly, 13 x 6.50 x 6

NOTE: The tire and hub are not sold separately and they are included in Wheel Assembly (045986).


045986 Wheel Assembly, 13” x 6.5” x 6” 1

1 P293 Seal, TRB, 3/4” ID 2

2 P292 Bearing, Tapered Roller, 3/4” ID 2

3 P402 Bearing Race Insert, 3/4" TRB 2


Drive SystemWheel Assembly, 13 x 6.50 x 6 2

LT0053


Drive SystemHand Contol Assembly2

2.12 Hand Contol Assembly

Screw, 1/4-28 x 1/4” BO SH Cup Pt Set

NOTE: Right and Left Control Handle Arm Assemblies are mirror images of each other with the exception of the Control Arm Weldment (item 2).


049706 Arm Assembly, Right Control Handle Right Side Only 1

049707 Arm Assembly, Left Control Handle Left Side Only 1

1 028390 Grip, Handle 1

2 027015 Arm Weldment, 2561 Right Control Right Side Only 1

027016 Arm Weldment, 2561 Left Control Left Side Only 1




6 048393 Mount, Extended Drive Handle Serial #1940106 and later 1

043950 Block, Drive Handle Mount Serial #1520306 and prior 1

7 P05035 Collar, 5/8” ID Lock 2

8 F05005-105 2

9 014834 Bearing, w/Snap Ring 5/8” ID 2

10 F05010-124 Nut, 3/8-16 Half Nyloc 1


12 F05010-58 Nut, 5/16-18 Nylok Hex 1

13 043952 Arm Pivot Weldment, Right Control 1

14 F05010-1 Nut, 3/8-16 Hex 1


056450 Turnbuckle Assembly, Hydro Diesel 1

16 018739 Rod End, 3/8-24 Right Hand 1

17 F05010-123 Nut, 3/8-24 Free 1

18 056449 Rod, Hydro Control Link 1

19 F05010-119 Nut, 5/16-24 Jam LH 1

20 014815 Rod End, 5/16-24 Male LH 1


Drive SystemHand Contol Assembly 2

LT0056


Drive SystemControl Box Assembly2

2.13 Control Box Assembly

Screw, 6-32 x 3/4” SBHC SS

Clamp, Blade Switch Mount

Switch, Blade Start/Stop

Hour Meter, Digital LCD

Key, Ignition

Switch, Ignition Key

Control Box Weldmnt, AC Gas w/ Throttle


Washer, 5/16” Split Lock

Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc

Light Assy, LED Red 3/16” FI Male Quicks

Bolt, #10-24 x 1/2” Phillips PH

Washer, #10 Split Lock

Plate, Control Box Access

Nut, #6-32 Keps

Light, Red 12 Volt .187 Tabs

Socket, 12V Accessory Panel Mount

Alarm, 3372 / 3386



Washer, Throttle Friction

Handle Weldmnt, Throttle

Knob, 1 3/8” x 3/8-24

Washer Plate, Throttle Friction

Washer, Throttle Friction

Bolt, 1/4-20 x 5/8” Hex Head Grade 5


Clamp, Cable

Bolt, 3/8-16 x 1 1/4” Carriage Grade 5

Nut, 5/16-18 Hex


Cable Assembly, 2861 Throttle

Grommet, Cable Wiper

Boot, Vinyl Cable

REF PART # DESCRIPTION COMMENTS QTY

056250 Control Box Assembly, Gas w/Buzzer 1

1 F05004-93 6

2 043956 2

3 044588 1

4 046129 1

5 045693 2

6 046122 1

7 055481 1

8 F05011-17 3

9 F05011-13 3

10 F05006-102 3

11 050477-1 1

12 F05015-17 2

13 F05011-20 2

14 048953 1

15 F05010-59 2

16 E20482 1

17 041669 1

18 049306 1

19 F05010-10 1

20 F05011-3 1

21 046239 1

22 044715 1

23 019086 1

24 046251 1

25 046293 1

26 F05005-137 2

27 F05011-14 2

28 061974 1

1 061974 replaced 046240 Throttle Conduit Clamp (serial # 33600109 and later). Also, 063206 replaced 049856 Throttle Cable. Ser-vice Kit (063210) was created for models with serial # prior to 33600109. See bulletins PB-0256 and IS-0257 for more information.

1

29 F05007-127 1

30 F05010-17 1

31 F05006-27 1

0632061 Cable Assembly, Gas Throttle 1

32 049856 1

33 061954 1

34 061953 1



Drive SystemControl Box Assembly 2

CM0003


Drive SystemPedal Assembly (Optional as of serial #26270307)2

2.14 Pedal Assembly (Optional as of serial #26270307)

Rod Weldment, Foot Control


Washer, 3/8” Push Nut

Nut, 3/8-24 Free

Pin, 3/8” x 1 5/16” Clevis

Pin, 1/8” x 3/4” Cotter

Yoke, 3/8In-24

Grip, Foot Control Black

Pedal Weldment, Foot Control

Bushing, 3/4” ID x 1” OD x 1” Oil

Washer, 20mm Bellville

Washer, 3/4” AN Yel/Cad

Ring, 3/4” External - External


NOTE: To add this Foot Pedal option to your unit after serial #26270307, order Foot Pedal Kit (056241).


056241 Pedal Kit, AGC Foot Optional 1

049739 Rod Assembly, Foot Control 2

1 049738 1

2 F05011-3 1

3 F05011-110 1

4 F05010-123 1

5 P110 1

6 F05012-3 1

7 P686 1

049728 Pedal Assembly, Control 2

8 P629 1

9 049730 1

10 029842 2

11 F05011-111 1

12 F05011-77 1

13 F04254-46 1

14 P107 1

IS-0218 Instruction Sheet, 056241 Kit 1


Drive SystemPedal Assembly (Optional as of serial #26270307) 2

LT0067


Drive SystemThrottle Assembly (Deleted after Serial # 24321106)2

2.15 Throttle Assembly (Deleted after Serial # 24321106)

NOTE: Throttle moved to control box location after Serial #24321106.


1 049856 Cable Assembly, 2861 Throttle 1

2 046240 Clamp, Throttle Conduit 1

3 019086 Knob, 1 3/8” x 3/8-24 1

4 F05015-17 Bolt, #10-24 x 1/2” PH 1

5 F05007-127 Bolt, 3/8-16 x 1 1/4” Carriage Grade 5 1

6 046251 Washer Plate, Throttle Friction 1

7 046293 Washer, Throttle Friction 1

8 046236 Handle Weldment, Throttle 1

9 046239 Washer, Throttle Friction 1


11 F05010-10 Nut, 3/8-16 Hex Nyl Lock 1


Drive SystemThrottle Assembly (Deleted after Serial # 24321106) 2

049544T


Drive SystemFront Deck Lift Rod Assembly (Serial #24311106 and prior)2

2.16 Front Deck Lift Rod Assembly (Serial #24311106 and prior)





3 034930 Plate Weldment, Deck Height Adjustment 1

4 F05010-10 Nut, 3/8-16 Hex Nyloc 10

5 048468 Rod End, 7/16-20 x 3/8 High Misalign 2



8 047234 Spring, .72 x 2.75 x .095 Dia SS Comp 1

9 047187 Spacer, 5/8” x 1” x 5/8” 1

10 F05010-38 Nut, 7/16-20 Jam 2

11 049787 Turnbuckle, Deck Lift Link 2

12 F05010-166 Nut, 3/8-24 LH Jam 2

13 018740 Rod End 3/8-24 Left Hand 2

14 S12284 Tube, 7/8” Dia Elec Motor Spacer 2

15 F05010-124 Nut, 3/8-16 Half Nyloc 1

16 F05004-123 Bolt, 3/8-16 x 3 1/2” Hex Head Gr5 1

17 P111 Ring, Kick-out, 1” 1

18 P212 Pin, 3/8” x 2 1/8” Clevis, Yzn 1

19 048712 Bushing, 1-1/16" Urethane Pivot Apply water-proof axle grease to mating surfaces prior to assembly

2

20 048692 Strap, 1U 2

21 F05006-81 Bolt, 5/16-18 x 1 3/4” FT Hex Head Gr5 Added after serial # 1940306 1

22 F05010-17 Nut, 5/16-18 Hex Added after serial # 1940306 1

23 P04211 Knob, 5/8-18 Ball 1

24 F05007-73 Bolt, 3/8-16 x 3” Hex Head Gr5 1

25 049545 Rod Weldment, Front Deck Lift 1


Drive SystemFront Deck Lift Rod Assembly (Serial #24311106 and prior) 2

049544


Drive SystemFront Deck Lift Rod Assembly (Serial #24331106 and later)2

2.17 Front Deck Lift Rod Assembly (Serial #24331106 and later)


Tube, 7/8” Dia. Elec Motor Spacer

Rod End 3/8-24 Left Hand


Nut, 3/8-24 LH Jam

Turnbuckle, Deck Lift Link

Nut, 7/16-20 Jam

Rod End, 7/16-20 x 3/8” High Misalign



049544 Rod Assembly, Front Deck Lift 1



3 055464 Plate Weldment, Deck Height Adjust 1

4 F05010-10 Nut, 3/8-16 Hex Nyloc 6

5 P04211 Knob, 5/8-18 Ball 1

6 048187 Handle Weldment, Deck Raise 1


8 047234 Spring, .72” x 2.75” x .095” Dia. SS Comp 1


10 049545 Rod Weldment, Front Deck Lift 1


12 F05010-124 Nut, 3/8-16 Half Nyloc 1

13 048712 Bushing, 1 1/16" Urethane Pivot Apply water-proof axle grease to mating surfaces prior to assembly

2

14 048692 Strap, 1U 2

15 P212 Pin, 3/8” x 2 1/8” Clevis 1

16 P111 Ring, 1” Kick-Out 1

049788 Rod Assembly, Deck Lift Link 2

17 F05010-10 2

18 S12284 1

19 018740 1

20 F05007-119 2

21 F05010-166 1

22 049787 1

23 F05010-38 1

24 048468 1


Drive SystemFront Deck Lift Rod Assembly (Serial #24331106 and later) 2

LT0057


Drive SystemEmergency Brake Assembly2

2.18 Emergency Brake Assembly


049550 Handle Assembly, E-Brake 1

1 P04211 Knob, 5/8-18 Ball 1

2 029360 Handle Weldment, E-Brake 1

3 F05010-10 Nut, 3/8-16 Hex Nyloc 2

4 P786 Bushing, 3/4” ID x 1” OD x 5/8” Lng Flanged 1

5 F05012-115 Pin, 3/4” Clevis Retaining 1


7 049537 Arm, E-Brake Link 1

8 029214 Spacer, 1.00” OD x .41” ID x 1/4” Thk Nylon-Blk 2

9 F05010-8 Nut, 1/2-13 Nyl Hex Lock 1


11 F05011-97 Washer, 1/2” Plain Belleville 6

12 029354 Block, E-Brake Pivot 1

13 029397 Rod Weldment, Brake Actuator 1

14 026407 Plate Weldment, E-Brake Lock 1

15 F05012-11 Pin, 3/16” x 1” Roll 1

16 026412 Rod Weldment, E-Brake Tensioner 1

17 F05012-1 Pin, 1/8” x 1” Cotter 1

18 P110 Pin, 3/8” x 1 5/16” Clevis 1

19 026409 Pulley, E-Brake 1

20 026416 Cable E-Brake 1


Drive SystemEmergency Brake Assembly 2

LT0055


Drive SystemRear Deck Lift Rod Assembly2

2.19 Rear Deck Lift Rod Assembly

Rod End 3/8-24 Left Hand

Nut, 3/8-24 LH Jam

Turnbuckle, Deck Lift

Nut, 3/8-24 UNF Hex Jam

Rod End, 3/8-24 Right Hand



049541 Rod Assembly, Rear Deck Lift 1


2 048712 Bushing, 1 1/16" Urethane Pivot Apply water-proof axle grease to mating surfaces prior to assembly.

2

3 048692 Strap, 1U 2


5 F05010-10 Nut, 3/8-16 Hex Nyloc 7


026448 Turnbuckle Assembly, Deck Lift 1

7 018740 1

8 F05010-166 1

9 026447 1

10 F05010-22 1

11 018739 1

12 026446 Rod Wldmnt, Spring Tensioner 1

13 F05011-101 Washer, 1/2” SAE Flat Gr5-8 (Thru Hard) 1

14 055442 Washer, 1/2” Delrin 1

15 026443 Block, Spring Tensioner 1

16 026371 Spring, 1 3/8" x 15.8” x .187” Extension 2

17 046534 Mount, Spring 1

18 F05007-109 Bolt, 3/8-16 x 4 3/4” Hex H ead Grade 5 1

19 049542 Rod Wldmnt, Rear Deck Lift 1

20 P110 Pin, 3/8” x 1 5/16” Clevis Serial # 1940306 and later 2

F05012-8 Pin, 3/8” x 1 3/32” Clevis Serial # 1520306 and prior 2



Drive SystemRear Deck Lift Rod Assembly 2

LT0058


Drive SystemFramework2

2.20 Framework



1 F05010-58 Nut, 5/16-18 Nylon Lock Hex 1

2 F05011-17 Washer, 5/16” SAE Flat 1

3 024155 Clamp, 1/4” Wire 13/32 Mtg Hole 1

4 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 1


6 047234 Spring, .72” x 2.75” x .095” Dia SS Comp 2

7 F05010-10 Nut, 3/8-16 Hex Nyloc 2

8 F05010-14 Nut, #10-24 Keps 4

9 043459 Switch, DPST NO 5A Plunger 3

10 F05004-126 Screw, 10-24 x 3/4” Phillips PH Machine 4

11 046559 Switch, DPST N/O N/C 1

12 F05004-1 Screw, 10-24 x 1/2” Sl Hex Machine 4

13 F05011-20 Washer, #10 Split Lock 4

14 044021 Cover, Handle Lockout Switch Left 1

15 044020 Cover, Handle Lockout Switch Right

16 049870 Bushing, Urethane Pivot Apply water-proof axle grease to mating surfaces prior to assembly

6

17 P195 Cap, Hub 1

18 049984 Sure Grip, Foot Pan 1

19 055841 Sure Grip, 1 1/2” Bar 1


21 P611 Holder, Jumbo Cup Black 2

22 046477 Wheel Yoke Assembly, 13” Comm See Section 2.10 1


Drive SystemFramework 2

LT0068


Drive SystemPull Bar Assembly2

2.21 Pull Bar Assembly

Bar Weldment, Pull


Nut, 5/8-11 FlexLoc

Washer, 5/8” Standard Flat


049488 Bar Assembly, Pull 1

1 049484 1

2 F05009-35 4

3 F0510-185 4

4 F05011-40 2


Drive SystemPull Bar Assembly 2

3373_018


Drive SystemRoller Assembly Upgrade Kit (Optional)2

2.22 Roller Assembly Upgrade Kit (Optional)

NOTE: Apply anti-seize to pivot bolts prior to assembly.

NOTE: Lubricate grease fittings using water-proof grease until discharge is visible from seals and bushings.


063377 Upgrade Kit, 61-73 AGC Roller Optional 1

1 P04211 Knob, 5/8-18 Ball 1

2 048930 Roller Lift Pivot Wldmnt 1

3 F05009-111 Bolt, 5/8” x 1/2” Shoulder 2

4 F05011-107 Washer, .625 ID x 1.312 OD x .050 Thick Nylon 4



7 F05010-8 Nut, 1/2-13 Hex Nylon Lock 11

8 063378 Pivot Collar Mount Weldment 61-73AGC 1

9 029109 Spacer, 3/16” Thk Deck Height 1


11 063382 Plate, Clamp Pivot Collar Mount 2

12 F04254-46 Ring, 3/4” External Retaining 1

13 F05011-77 Washer, 3/4” AN Yel/Cad 1

14 029842 Bushing, 3/4” ID x 1” OD x 1” Oil 2

15 063384 Spacer, Lift Link Arm 61-73 AGC 2

16 063383 Arm, Roller Lift Link 61-73 AGC 1

17 048941 Strip, Roller Wiper 1

18 F05011-17 Washer, 5/16” SAE Flat 3






24 023541 Bearing, 1” Flanged Mount 2

25 048908 Roller Weldment, 3373 Stripping 1

26 048910 Frame Weldment, Upgrade Kit 1




30 063870 Tube, Roller Mount Spacer 2

31 019094 Plate, Drive Motor Mount 2

32 063869 Plate, Roller Mount 1

33 F05010-185 Nut, 5/8-11 Flexlock 2

IS-0277 Instruction Sheet, 61-73 Roller Assembly 1


Drive SystemRoller Assembly Upgrade Kit (Optional) 2

290006


Drive SystemStriping Kit (Optional)2

2.23 Striping Kit (Optional)

NOTE: This 042947 Striping Kit may be purchased through your Lastec Dealer.


042947 Striping Kit, Commercial Mower 1

1 042951 Bracket Weldment, Left Striping Kit 1

2 042950 Bracket Weldment, Right Striping Kit 1

3 042949 Plate Weldment, Hanger Strap 1

4 042943 Plate, Mount Washer 2



7 042945 Pad, Rubber Striping 1

8 042942 Strap, Rubber Pad Mounting 1



IS-0192 Instruction Sheet, 61” Deck Striping Kit 1


Drive SystemStriping Kit (Optional) 2

LT0045


Lastec//072815 3-1

3

SECTION 3 HYDRAULIC SYSTEM

Hydraulic SystemHydraulic Layout Diagram (Serial #46570113 and later)3

3.1 Hydraulic Layout Diagram (Serial #46570113 and later)

Hydraulic Mainentance Kits


1 072587 Hose Assembly, 1/2” HP x 30” ORFS 8 ST 4

2 072599 Hose Assembly, 3/8” LP x 16.5” ORFS 6 45 2

3 072597 Hose Assembly, 3/8” LP x 6” ORFS 6 90 2

4 072598 Hose Assembly, 3/8” LPx12” ORFS 6 ST 2


049928 Kit, Hydro Oil Repl 5 Gal 3372 1

028535 Oil, Shell TTF-SB 5 gal

P620 Filter Element, Spin On, BE-25-25 Zinga 4

049929 Kit, Hydro Oil Repl 2 1/2 Gal 3372 1

028535 Oil, Shell TTF-SB 2.5 gal


040642 Oil,TTF-SB 32 oz. Bottle Hydro 1

028535 Oil, Shell TTF-SB 1 qt.

040630 Decal, Hydraulic TTF-SB Oil 1

040635 Black Cap, for 32 oz. Bottle Oil Container 1

040636 Bottle, 32 oz. Container for Oil 1

040637 Spout Cap/ W Red Seal for 32 oz. Container 1

047600 Kit, Hydro-Gear Flow Test 1

048400 Seal Kit, Hydro-Gear BDP 10-12 Seal Kit for Pumps 1

3-2 Lastec//072815 Hydraulic System

Hydraulic SystemHydraulic Layout Diagram (Serial #46570113 and later) 3

290013-2

TANK

FILTERS

PUMP

PUMP

MOTOR MOTOR

Hydraulic System Lastec//072815 3-3

Hydraulic SystemHydraulic Layout Diagram (Prior to Serial #46570113)3

3.2 Hydraulic Layout Diagram (Prior to Serial #46570113)

Hydraulic Mainentance Kits


1 041180 Hose Assembly, 26” OAL x 1/2” Hyd Serial #1700206 and later 4

045990 Hose Assembly, 1/2 x 15 1/2” JIC Serial #1690206 and prior 4

2 045970 Hose, 3/8” Hyd x 3 1/4” Low Pressure 2

3 015485 Fitting, 3/8” Barb Tee 1

4 049857 Hose, 3/8” Hyd x 12” Low Pressure 4

5 045972 Hose, 3/8” Hyd x 9 1/2” Low Pressure 1

061807 Hose Clamp, Dixon Worm Gear HSS6 Not Shown 12


049928 Kit, Hydro Oil Repl 5 Gal 3372 1

028535 Oil, Shell TTF-SB 5 gal


049929 Kit, Hydro Oil Repl 2 1/2 Gal 3372 1

028535 Oil, Shell TTF-SB 2.5 gal


040642 Oil,TTF-SB 32 oz. Bottle Hydro 1

028535 Oil, Shell TTF-SB 1 qt.

040630 Decal, Hydraulic TTF-SB Oil 1

040635 Black Cap, for 32 oz. Bottle Oil Container 1

040636 Bottle, 32 oz. Container for Oil 1

040637 Spout Cap/ W Red Seal for 32 oz. Container 1

047600 Kit, Hydro-Gear Flow Test 1

048400 Seal Kit, Hydro-Gear BDP 10-12 Seal Kit for Pumps 1


Hydraulic SystemHydraulic Layout Diagram (Prior to Serial #46570113) 3

F F

P P

Tank

Motor Motor

LT0076


Hydraulic SystemHydraulic Pump Assemblies3

3.3 Hydraulic Pump Assemblies

Bushing, 15mm Split Taper



Sheave, BK60 QT

Key, 5mm x 5mm x 25mm




Fitting, 6 ORFS - 6 STOR 90

Bolt, 5/16-18 x 1 3/4” Hex Head

Spacer, Hydro Actuator


Pump, 12cc Hydrostatic

Pump, 12cc Hydrostatic

Actuator Kit, RTN Std for Model 2861

Fitting, 8 ORFS - 8 STOR LL 90

Turnbuckle Assembly, Hydro

Rod End, 5/16-24 Male LH

Nut, 5/16-24 Jam LH

Rod, Hydro Control Link

Nut, 3/8-24 Free

Rod End, 3/8-24 Right Hand

NOTE: Left and right pump assemblies are mirror images of each other. (Right Pump Assembly shown below.)


049837 1

1 072560 replaced (2) 026393 Fitting, #8 SAE / #8 JIC 90 X-L Elbow, (2) 072585 replaced (1) 026394 Fitting, #6 SAE x 3/8” Hose Str and (1) P12722 Fitting, #6 90 Deg SAE #6 Hose Barb Hyd; 072587 replaced 041180 Hose Assembly, 26” OAL x 1/2” Hyd; removed 045970 Hose, 3/8” Hyd x 3-1/4 Low Pressure and 061807 Hose Clamp, Dixon Worm Gear HSS6 (Serial #46570113 and later).

Pump Assembly, 12cc Right Hydro Right Side 1

0498361 Pump Assembly, 12cc Left Hydro Left Side 1

1 019359 1

2 F05011-14 2

3 F05005-101 Tighten bolts to 84 in-lbs 2

4 018773 1

5 048532 1

6 F05007-78 1

7 F05011-3 2

8 F05010-10 2

9 072585 2

10 F05009-70 1

11 026399 1

12 F05010-58 1

13 048284 2

2 Pumps include the Actuator Kit (046820) already installed.

Right Pump 1

048285 2 Left Pump 1

046820 Parts not sold separately 1

14 072560 2

15 0725871 Hose Assembly, 1/2HP x 30In ORFS 8 ST 2

16 026470 Belt, BX54 1

049838 2

17 014815 1

18 F05010-119 1

19 049839 1

20 F05010-123 1

21 018739 1


Hydraulic SystemHydraulic Pump Assemblies 3

LT0139-1


Hydraulic SystemHydraulic Motor, Right3

3.4 Hydraulic Motor, Right

Drum, 152.4mm w/Studs

Brake, 152.4 x 25 Cam

Key, 5/16” x 1” Woodruff

Hex Nut, 1-20 Slotted


049965 Wheel/Motor Assembly, 2861 Right Rear 1

1 P04646 Nut, 1/2-20 Lug Torque to 144 ft.-lbs. 5

2 F05011-115 Washer, 1” ID .03 SS Shim As Req’d


4 043320 Brake Assembly, 3377TZ Rear Drum See Section 3.6 for parts 1

043320-1 1

043320-2 1

5 F05010-121 Nut, 5/16-18 Nylon Locking Jam 1

6 F05011-16 Washer, 5/16” Standard Flat 1

7 F05006-102 Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc 1

8 F05006-117 Bolt, 5/16-18 x 3/4” SHC SS 4



11 F05010-8 Nut, 1/2-13 Nyl Hex Lock 4

12 F05011-101 Washer, 1/2” SAE Flat Grade 5-8 (Thru Hard) 4

13 071864 1

1 071864 replaced (2) 072561 Fitting, 8 ORFS - 10 STOR 45 (Serial #47960513 and later). 072561 replaced (2) 016807 Fitting, #10 SAE-1/2” JIC 45 Elbow (Serial #46570113 to #47950513).

Fitting, 8 ORFS - 10 STOR 90 2


15 055177 Plate, E-Brake Pulley Right Serial # 2760706 and later 1

027056 Plate, E-Brake Pulley Right Serial # 2750706 and prior 1



18 055151 Plate, E-Brake Cable Retaining 1

19 F05010-124 Nut, 3/8-16 Half Nyloc 1

20 F05012-49 Pin, 1/8” x 1 1/2” Cotter 1

21 046659 Motor, Right Hydro-Gear Drive 1

22 046800 1

23 026417 1

026439 Tire Assembly, 24” x 12-12 Turf Master Not Shown 1

041098-1 Tire, 24” x 12-12 (Tire Only) 1

026440 Rim, 12” x 8 1/2” 8 Spoke 4 1/2” BC 1


Hydraulic SystemHydraulic Motor, Right 3

LT0069C


Hydraulic SystemHydraulic Motor, Left3

3.5 Hydraulic Motor, Left



Key, 5/16” x 1” Woodruff

Hex Nut, 1-20 Slotted


049966 Wheel/Motor Assembly, 2861 Left Rear 1

1 P04646 Nut, 1/2-20 Lug Torque to 144 ft.-lbs. 5



4 043320 Brake Assembly, 3377TZ Rear Drum See Section 3.6 for parts 1

043320-1 1

043320-2 1

5 F05010-121 Nut, 5/16-18 Nylon Locking Jam 1

6 F05011-16 Washer, 5/16” Standard Flat 1


8 F05006-117 Bolt, 5/16-18 x 3/4” SHC SS 4



11 F05010-8 Nut, 1/2-13 Nyl Hex Lock 4

12 F05011-101 Washer, 1/2” SAE Flat Grade 5-8 (Thru Hard) 4

13 071864 1

1 071864 replaced (2) 072561 Fitting, 8 ORFS - 10 STOR 45 (Serial #47960513 and later). 072561 replaced (2) 016807 Fitting, #10 SAE-1/2” JIC 45 Elbow (Serial #46570113 to #47950513).

Fitting, 8 ORFS - 10 STOR 90 2



16 055178 Plate, E-brake Pulley Left Serial # 2760706 and later 1

027057 Plate, E-brake Pulley Left Serial # 2750706 and prior 1



19 055151 Plate, E-Brake Cable Retaining 3

20 F05010-124 Nut, 3/8-16 Half Nyloc 3

21 F05012-49 Pin, 1/8” x 1 1/2” Cotter 1

22 046661 Motor, Hydro Gear 1

23 046800 1

24 026417 1

026439 Tire Assembly, 24” x 12-12 Turf Master Not Shown 1

041098-1 Tire, 24” x 12-12 (Tire Only) 1

026440 Rim, 12” x 8 1/2” 8 Spoke 4 1/2” BC 1


Hydraulic SystemHydraulic Motor, Left 3

LT0070C


Hydraulic SystemBrake Assembly3

3.6 Brake Assembly


Stud, 1/2-20 x 1-1/4 Press In


Shoe, 152.4 x 25 Brake

Spring, 152.4 x 25 Brake Return

Cam, 152.4 x 25 Brake

Backing Plate, 152.4 x 25 Brake

Arm, 152.4 x 25 Brake Actuator

Clip, 152.4 x 25 Retainer


043320 Brake Assembly, Rear Drum Includes Items 1 to 8 1

1 043320-1 Includes Item 2 1

2 043320-4 5

043320-2 Includes Items 3 to 8 1

3 043320-9 2

4 043320-10 2

5 043320-8 1

6 043320-7 1

7 043320-5 1

8 043320-6 1


Hydraulic SystemBrake Assembly 3

3300_045


Hydraulic SystemHydraulic Tank Assembly (Serial #46570113 and later)3

3.7 Hydraulic Tank Assembly (Serial #46570113 and later)

Fitting, 6 ORFS - 6 PushLok 45

Hose, 3/8” Hyd x 14” Low Press.

Fitting, 6 ORFS - 6 PushLok ST



Fitting, 6 ORFS - 6 PushLok 90




072591 Tank Assembly, 29AGC Hyd 1

1 P12708 Fitting, 3/8” NPT-3/8” Barb Elbow 2

2 072505 Hose Clamp, 3/16” Spring 2

3 047883 Tube, Vinyl Sight Gage 1

4 072584 Fitting, 6 ORFS - 6 MPT 45 2

5 072556 Fitting, 6 ORFS - 6 MPT 90 6

6 049891 Hose, 3/8” Low Pressure 28” 1

7 P12724 Fitting, 3/8” NPT-3/8” Barb 3

8 043251 Bushing, Hex, 3/4” x 3/8” 1

9 072582 Tank Weldment, 28AGC Hyd 1

10 F05010-124 Nut, 3/8-16 Half Nylock 4



13 F05005-79 Bolt, 1/4-20 x 1/2” HHC 4


15 P619 Filter Head, 3/8” NPT 2

16 P620 Filter Element, Spin On, BE-25-25 Zinga 2

17 027066 Hose, 2561 Oil Drain Includes (2) Fittings (P12724) 1

18 028593 Clamp. 3/4” EMY Coated 1

19 P04332 Cap, 3/8” Pipe Galvanized 1

072599 Hose Assembly, 3/8” LPx16.5” ORFS 6 45 2

20 072600 1

21 072596 1

22 072541 1

072597 Hose Assembly, 3/8” LP x 6” ORFS 6 90 2

23 072541 1

24 072594 1

25 072539 1

072598 Hose Assembly, 3/8” LP x 12” ORFS 6 ST 2

26 072541 2

27 072595 1

28 041083 Valve, Two Tank Diverter 1


Hydraulic SystemHydraulic Tank Assembly (Serial #46570113 and later) 3

290012


Hydraulic SystemHydraulic Tank Assembly (Priot to Serial #46570113)3

3.8 Hydraulic Tank Assembly (Priot to Serial #46570113)


055897 Tank Assembly, 29HP Hyd 1

1 P12708 Fitting, 3/8” NPT-3/8” Barb Elbow 1 added after Serial # 3011006 7

2 P649 Hose Clamp, 7/32”-5/8” 2

3 047883 Tube, Vinyl Sight Gage 1

4 048988 Fitting, 3/8” NPT - 3/8” Barb 45 Deg 2

5 061807 Hose Clamp, Dixon Worm Gear HSS6 Serial # 33401208 and later 9

P12739 Hose Clamp, 11/16” Worm Serial # 33391208 and prior 9

6 049857 Hose, 3/8” Hyd x 12” Low Press. 4

7 049891 Hose, 3/8” Low Pressure 28” 1

8 P12724 Fitting, 3/8” NPT-3/8” Barb Includes (2) Fittings (027066) 3

9 043251 Bushing, Hex, 3/4” x 3/8” 1

10 049596 Tank Weldment, 2861AGC Hyd 1

11 028492 Plug, 3/8” NPT Hex Brass 1 removed after Serial # 3011006 1

12 F05010-124 Nut, 3/8-16 Half Nylock 4



15 F05005-79 Bolt, 1/4-20 x 1/2” HHC 4


17 P619 Filter Head, 3/8” NPT 2

18 P620 Filter Element, Spin On, BE-25-25 Zinga 2

19 028493 Fitting, 3/8” NPT F-M-F Tee Serial # 3011006 and later 1

028072 Fitting, 3/8” NPT Street Tee Serial # 3001006 and prior 1

20 045972 Hose, 3/8” Hyd x 9 5/8” Low Press. 1

21 027066 Hose, 2561 Oil Drain Added after serial # 3011006 1

22 028593 Clamp. 3/4” EMY Coated Added after serial # 3011006 1

23 P04332 Cap, 3/8” Pipe Galvanized Added after serial # 3011006 1



Hydraulic SystemHydraulic Tank Assembly (Priot to Serial #46570113) 3

290005


Hydraulic SystemHydraulic Drive Idler Assembly3

3.9 Hydraulic Drive Idler Assembly


049570 Idler Assembly, Hydro Drive 1

1 F05010-8 Nut, 1/2-13 Nylon Hex Lock 2

2 F05011-2 Washer, 1/2” SAE Flat Added after serial # 2200406 2

3 049571 Rod, Polyurethane Spring 4

4 049569 Arm Weldment, Hydro Tensioner 1


6 046144 Pulley, 5” OD Idler 1


Hydraulic SystemHydraulic Drive Idler Assembly 3

LT0078


Lastec//072815 4-1

4

SECTION 4 ENGINE & ELECTRICAL

Engine & ElectricalFuel Tank Assembly (Serial #46570113 and later)4

4.1 Fuel Tank Assembly (Serial #46570113 and later)

Gauge, Fuel Indicator Sealed

Grommet, Fuel Gauge Sealed

Fitting,1/4” Barb 90 Tank w/3" Long Tube

Grommet, Fuel Tank Fitting

Tube, Fuel Pick Up

Vent, Remote w/Valve

Grommet, Remote Vent

Tube, 3.5" Vapor Neck


067359 Tank Assembly, Gasoline Dual Fittings 1

1 067363 Cap, Gas Fuel Tank Ratchet 350 1

2 F05004-18 Screw, 10-24 x 5/8” Unsl Indent HH Machine 2


4 085614 Grommet, Rubber 2 1/2” Dia 3

5 043441 Washer, Fuel Tank Retaining 1

6 019696 Cap, Hyd Tank (P631) 3

7 043442 Washer, Fuel Tank Double 1

072858 1

1 Replaced 067361 Fuel Dual Fitting Tank Assembly (9/14).

Tank Assembly, 7 Gallon Gas Dual Fitting Includes Fuel Tank 1

8 072735 1

9 072736 1

10 049809 1

11 028818 2

12 055446 1

13 064653 1

14 064654 1

15 067364 1

16 045897 Plate, Decal Fuel 1

17 F05004-285 Screw, 10-24 x 5/8” SBHC SS 2

18 F05010-160 Nut, 10-24 Hex Nylock 2

4-2 Lastec//072815 Engine & Electrical

Engine & ElectricalFuel Tank Assembly (Serial #46570113 and later) 4

LT0138B

Engine & Electrical Lastec//072815 4-3

Engine & ElectricalFuel Tank Assembly (Serial #25620207 to #46560113)4

4.2 Fuel Tank Assembly (Serial #25620207 to #46560113)

Gage, Fuel Indicator

Grommet, Fuel gage

Fitting,1/4” Barb 90 Tank w/ 3" Long Tube

Grommet, Fuel Tank Fitting

Tube, Fuel Pick Up


045973 Tank Assembly, Gasoline Dual Fittings 1

1 063252 Cap, Gas Fuel Tank Vented 1



4 085614 Grommet, Rubber 2 1/2” Dia 3

5 043441 Washer, Fuel Tank Retaining 1

6 019696 Cap, Hyd Tank (P631) 3

7 043442 Washer, Fuel Tank Double 1

055438 Tank Assembly, Fuel Dual Fitting Includes Fuel Tank 1

8 049908 1

9 049909 1

10 049809 1

1 Replaced 1/4” Barb 90 Tank Fitting (028820) and 1/4” x 2" Long Tygon Tubing (046532) (Serial #39030111 and later).

1

11 028818 2

12 055446 1

13 045897 Plate, Decal Fuel 1

14 P485 Decal, Fuel Equipment 1


Engine & ElectricalFuel Tank Assembly (Serial #25620207 to #46560113) 4

LT0074


Engine & ElectricalFuel System4

4.3 Fuel System

Hose Clamp, 1/2” Spring

Hose, Fuel 1/2” x 2-1/4”

Fuel Pump Module

Strap, Fuel Pump Mount

Fuel Pump

Bracket, Fuel Pump Bottom

Spacer, Fuel Pump Mount

Grommet, Fuel Pump Mount

Screw, 10-24 x 1 1/4” Unsl Ind HH Machine

Washer, #10 SAE Flat

Nut, 10-24 Hex Nylock

Hose, Fuel 5/16” x 15” Lng

Hose, Fuel 5/16” x 42” Lng

Hose Clamp, 5/16” Spring


1 072506 1

1 (21) 072506 replaced (21) P649 Hose Clamp, 7/32”-5/8”, (2) 072588 replaced (2) 061807 Clamp, 7/16-25/32 Worm and (4) 072507 replaced (4) P649 Hose Clamp, 7/32”-5/8” (Serial #46570113 and later).

Hose Clamp, 1/4” Spring 21

2 045588 Hose, 1/4” x 16” Fuel 2

3 048998 Hose, Fuel 1/4” x 48” 1

4 019298 Hose, Fuel, 1/4” x 8”, 325E98 1

5 046762 Filter, Fuel 1/4” 1

6 046772 Adapter, Fuel Hose Reducer 1

0467701 Fuel Pump Assembly, 29Hp 1

7 072588 2

8 046771 1

046765 1

9 046769 Not Sold Separately 1





14 F05004-19 2

15 F05011-18 2

16 F05010-160 2

17 055924 1

18 055896 1

19 072507 4

20 040388 Hose, Fuel 1/4” x 32" 2


22 067370 Carbon Canister, 9 Gal Added (Serial #46570113 and later) 2

23 067973 Hose Clamp, 3/16” Spring 2



26 F05010-220 Nut, 1/4-20 Flanged Hex Nylock 2


28 F05011-13 Washer, 5/16 Split Lock 1

29 045320 Hose, Fuel 1/4” x 36” 1

30 045328 Hose, Fuel 1/4” x 20” 2

31 045585 Hose, Fuel 1/4” x 14” 1

32 064658 Fitting, 1/4” Tee Barb 1


Engine & ElectricalFuel System 4

Return Line

To Injectors

To Engine CARB Port

290013-1

Fuel pump attachedto underside

of battery tray


Engine & ElectricalEngine Guard Assembly4

4.4 Engine Guard Assembly


044833 Guard Assembly, AC Series 1

1 F05010-160 Nut, 10-24 Hex Nylock 2

2 P06104 Foot, Rubber 2

3 F05004-35 Screw, 10-24 x 1/2” SBHC 2

4 044835 Guard Weldment, AC Series 1

5 F05010-10 Nut, 3/8-16 Hex Nyloc 3

6 060169 Knob, 3/8” Bore Oval/Tapered Plastic Serial # 28190707 and later 1

S08291-W Handle, Power/Feed & Up/Down Serial # 28180707 and prior;No longer available: 0rder 060169

1

7 F05007-214 Screw, 3/8-16 x 2” SHC Serial # 3021006 and later 1

F05007-58 Screw, 3/8-16 x 2” BO SHC Serial # 3020906 and prior 1

8 F05007-129 Bolt, 3/8-16 x 1 3/4” FT Grade 5 2

9 027006 Spring, 1-1/8" x 7-1/2" x .091 Extension 1


Engine & ElectricalEngine Guard Assembly 4

LT0072


Engine & ElectricalEngine Assembly4

4.5 Engine Assembly

Clutch, 5.75 Dia x 1-1/8 Bore 12V

Capture Weldment, Clutch Stop


Washer, 5/16 SAE Flat

Stop Weldment, Clutch

Washer, 5/16 Star ET

Bolt, 5/16-18 x “1 Hex Head Grade 5

Hose, Clutch Stop Bushing


Nut, 3/8-16 Half Nyloc


046125 Engine Assembly, 29HP 1

1 047662 Spark Plug, Kawasaki 2

2 046126 Engine, Kawasaki 29HP 1

3 049847 Belt, B-134 Custom 61" Deck Only 1

055445 Belt, B-130 Custom 73" Deck Only 1

4 047663 Oil Filter, Kawasaki 1

5 046783 Air Intake Assembly See Section 4.9 1

6 048205 1 Radiator, Kawasaki 2961 1

7 046719 Radiator Cowling Assembly See Section 4.6 1

8 F05004-48 Bolt, M10-1.5 x 25mm Hex Head FT 8.8 Serial # 26670407 and later 4

F05007-123 Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5 Serial # 26660407 and prior 4

9 F05011-88 Washer, 10mm Split Lock Serial # 26670407 and later 4

F05011-4 Washer, 3/8” Split Lock Serial # 26660407 and prior 4

10 046760 Valve, Oil Drain 1

11 072588 2 Hose Clamp, 1/2” Spring 2

12 055895 Hose, Fuel 1/2” x 20” Long 1

13 P12724 Fitting, 3/8” NPT-3/8” Barb 1

14 P04332 Cap, 3/8” Pipe Galvanize 1

15 026396 Spacer, Clutch 1

16 029331 Sheave, BK60 1 1/8” 1

17 S21486 Key, 1/4” SQ x 3-3/8” Long 1

18 046143 Bushing, Clutch Spacer 1

19 F05011-117 Washer, 7/16” Nord-Lock 1

20 F81003-29 Bolt, M10-1.5 x 55mm Hex Head Full Thread G5 1

072684 3 Clutch Assembly, 5.75 Pitch 1 1/8 Bore 12V 1

21 0403113 1

22 059776 1

23 F05010-58 2

24 F05011-17 4

25 040338 1

26 F05011-33 2

27 F05006-27 2

28 044683 1

29 F05011-3 1

30 F05010-124 1

057507 Muffler, 29HP Kawasaki 49069-2356-Y Not Shown 1

056547 ECU, Kawasaki Not Shown 1

057002 Fan, Kawasaki Cooling-29HP Not Shown 1

072589 Screen, Radiator Kawasaki 29Hp Not Shown 1


Engine & ElectricalEngine Assembly 4

NOTE: For further breakdown of the Kawasaki engine, see your Kawasaki Owner’s Man-ual or check www.kawpower.com.

1 Radiator holds 2.9 qt. (2.7L). Use 50/50 mix of antifreeze and water.2 Replaced (2) 061807 Hose Clamp, Dixon Worm Gear HSS6 (Serial #46570113 and later).3 Replaced 029330 Electric Clutch/Brake w/hardware (Serial #48470613 and later). When replacing the original 029330 Ogura clutch,

please order 072691 Retrofit Kit (not 072684 clutch assembly listed in the parts table above).

290002-1C


Engine & ElectricalRadiator Cowling Assembly4

4.6 Radiator Cowling Assembly


046719 Radiator Cowling Assembly 1

1 F05010-69 Nut, 1/4-20 Nylon Lock 4

2 046739 Spring, Cowling Hinge 2

3 F05010-9 Nut, 1/4-20 Keps 2


5 F05010-160 Nut, 10-24 Hex Nylock 2

6 P06104 Foot, Rubber 2

7 046668 Cowling Weldment, 29HP Engine 1

8 F05004-35 Screw, 10-24 x 1/2” SBHC 2



11 046270 Rod Weldment, Cowling Pivot 1



Engine & ElectricalRadiator Cowling Assembly 4

290002-3


Engine & ElectricalMotor Mount and Hardware4

4.7 Motor Mount and Hardware




3 F05010-14 Nut, #10-24 Keps 4

4 F05011-18 Washer, #10 SAE Flat 4

5 P07584 Clamp, 1/2” EMT Coated 4


7 049564 Mount Weldment, Engine 1

8 F05010-10 Nut, 3/8-16 Hex Nyloc 4

9 P294 Fitting, 1/4-28 45 Deg Grease 1

10 027009 Guard, Right Hydro Fan 1

11 056244 Guard, Left Hydro Fan 1

12 F05006-101 Bolt, 5/16-18 x 3/4” Hex Head W/Flat&Lock Washer 2


14 F05011-68 Washer, 1/2” Standard Flat Zn 1

045271 Pulley Assembly, 5” OD Idler, V Groove 1

15 F04254-12 Ring, 62mm IR Din #472 Retaining 2

16 045270 Pulley, 5” OD Idler, V Groove 1

17 P103 Bearing, Spindle Top 6305 RS 1

18 045272 Boss, Idler Pulley Standoff 1


20 049705 Idler Assembly, Deck Drive See Section 4.8 for parts 1

050436 Relay, 40A 12VDC Automotive Not Shown 3


Engine & ElectricalMotor Mount and Hardware 4

290001-1


Engine & ElectricalDeck Drive Idler Assembly4

4.8 Deck Drive Idler Assembly

Ring, 62mm IR Din #472 Retaining

Pulley, 5” OD Idler, V Groove

Bearing, Spindle Top 6305 RS

Boss, Idler Pulley Standoff


049705 Idler Assembly, Deck Drive 1


2 F05011-68 Washer, 1/2” Standard Flat Zn 1

045271 Pulley Assembly, 5” OD Idler, V Groove 1

3 F04254-12 2

4 045270 1

5 P103 1

6 045272 1

7 049702 Plate Weldment, Deck Drive Idler 1


9 P786 Bushing, 3/4” ID x 1” OD x 5/8” Lng Flanged 2

10 F05012-115 Pin, 3/4” Clevis Retaining 1

11 F05012-21 Pin, 3/16” x 1” Cotter 1

12 026472 Tensioner Bushing 2

13 049701 Boss Weldment, Rubber Spring Tensioner 1

14 F05010-35 Nut, 1/2-13 Hex 2


16 049869 Spring, Urethane 1



Engine & ElectricalDeck Drive Idler Assembly 4

LT0081


Engine & ElectricalAir Filter Assembly4

4.9 Air Filter Assembly

Housing, Engine Air Filter

Air Filter, Inner Element

Air Filter, Primary Element

Housing Cap, Kohler Filter

Housing Cap Dirt Ejector, Kohler Filter


046783 Air Filter Assembly 1

1 046556 Hood, Rain 1

2 P09895 Clamp, 2 1/2” Worm 3

3 046786 Filter Bracket Weldment 1

4 F05004-237 Screw, M8 x 1.25 x 60 Hex Washer Hd w/o Serr Metric 1

5 046781 Bushing, Clamp Spring 1

6 046782 Spring, Filter Clamp 1

7 046785 Bracket, Upper 1

8 F05004-238 Screw, M8 x 1.25 x 14 Hex Washer Hd w/o Serr Metric 2

9 046788 Pipe, Intake 1

10 046787 Duct, Upper 1

046789 Filter Assembly, Engine Air 1

11 046780 1

12 046554 1

13 046553 1

14 046552 1

073357 Not Shown

057501 Gauge, Kawasaki Air Filter Minder Not Shown 1


Engine & ElectricalAir Filter Assembly 4

290002-2


Engine & ElectricalBattery Tray Assembly4

4.10 Battery Tray Assembly

Box, Battery Modified

Bolt, 5/16-18 x 8-1/2” Hex Head Grade 5

Angle, Battery Hold Down

Washer, Felt Battery Terminal

Battery, Group 26 w/Handle




Channel, Battery Box Spacer

Strap, 24” Rubber w/Hooks

Nut, 1/4-20 Nylock




044696 Tray Assembly, Commercial Battery 1

049700 Battery Assembly, 33HP 1

1 049599 1

2 F05006-123 2

3 026382 1

4 P12161 1

5 067381 1

6 F05006-27 2

7 F05011-13 2

8 F05011-17 2

9 049769 1

10 P11258 1

11 F05010-69 1

12 F05011-11 1

13 F05005-116 1

14 049896 Bracket, Left Seat Latch 1

15 049895 Bracket, Right Seat Latch 1


17 F05011-13 Washer, 5/16 Split Lock 4

18 042985 Plate Weldment, Battery Tray 1

19 028352 Clamp,1” ID Coated 1


Engine & ElectricalBattery Tray Assembly 4

LT0075B


Engine & ElectricalWiring Harness4

4.11 Wiring Harness

Wire # Gauge Color/Stripe From - To

1 1A-B 6 Red Bat +, Starter2 2A-B 6 Black Bat (neg), Eng Gnd3 2C-D 16 Black Eng Gnd, Seat Delay4 2E-F 16 Black Seat Delay, CR3 - 865 2G-H 16 Black CR3 - 86, CR2 - 866 2J-K 16 Black CR2 - 86, CR1 - 307 2L-M 16 Black CR1 - 30, CR1 - 868 2N-P 16 Black CR1 - 86, Key Switch - G9 2Q-R 16 Black Key Switch - G, Splice

10 2S-T 16 Black Splice, Hour Meter11 2U-V 16 Black Splice, Aux Power Outlet12 2W-X 16 Black Eng Gnd, Fuel Pump (neg)13 2Y-Z 16 Black Eng Gnd, Clutch14 3A-B 14 Red Starter +, Splice15 3C-D 14 Red F4 (25A), Eng616 4A-B 16 Red/Black Key Switch - B, Splice17 4C-D 16 Red/Black Splice, F2 (10A)18 4E-F 16 Red/Black Splice, Blade Switch com C (NC)19 4G-H 16 Red/Black Blade Switch com C (NC), Oil Pressure Lamp20 4J-K 16 Red/Black Splice, Diagnostic Lamp21 4L-M 16 Red/Black Splice, Over Temp Alarm22 4N-P 16 Red/Black Key Switch - B, Seat23 4Q-R 16 Red/Black Seat, Brake 124 4S-T 16 Red/Black Brake 1, CR2 - 3025 4U-V 16 Red/Black CR2 - 30, Splice26 4W-X 16 Red/Black Splice, Eng627 5A-B 16 Red/Blue F1 (20A), Key Switch - L28 6A-B 16 White/Violet Blade Switch com C (NC), Right Neutral29 7A-B 16 Orange Right Neutral, Left Neutral30 8A-B 16 Orange/White Left Neutral, Brake 234 9A-B 16 Green Brake 2, CR3 - 8535 10A-B 16 Green/White Hour Meter +, Blade Sw com B (NO)36 10C-D 16 Green/White Blade Sw com B (NO), Left Neutral37 10E-F 16 Green/White Left Neutral, Brake 138 10G-H 16 Green/White Brake 1, Seat39 11A-B 16 Yellow/Black Right Neutral, Left Neutral41 12A-B 16 White Right Neutral, Brake 1 (NC)42 12C-D 16 White Brake 1 (NC), D1 Diode +43 12E-F 16 White D1 Diode (neg), CR1 - 8544 13A-B 16 White/Blue Blade Sw com B, Brake 145 14A-B 16 Green/Orange Blade Sw com B, CR2 - 8546 15A-B 16 Red/Green Key Switch - S, CR3 - 3047 16A-B 16 Red/Yellow CR4 - 87, Fuel Pump +48 17A-B 16 Black/White CR1 - 87, Eng349 18A-B 16 Brown CR4 - 86, Eng350 19A-B 16 Yellow CR2 - 87, Clutch 51 20A-B 16 Blue CR3 - 87, Starter Solenoid52 21A-B 16 Blue/Red Oil Pressure Lamp -, Eng653 22A-B 16 Black Key Switch - M, Eng654 23A-B 16 Red CR1 - 85, Clutch Delay55 24A-B 16 Red/White Eng3, Diagnostic Lamp56 25A-B 16 Yellow/White Over-Temp Alarm, Eng657 26A-B 16 Gray F3 (10A), CR4 - 8558 26C-D 16 Gray CR4 - 85, CR4 - 3059 26E-F 16 Gray CR4 - 30, Eng3 (Bullet)

29- 61-73AGC Kawasaki Harness Color Code rev. B.01Lastec Item #

*** All Wire Stranded GXL ***


Engine & ElectricalWiring Harness4

5/8"

Loo

m

Bra

ke 1

8"4"

Bra

ke 2

Tape

Hou

r M

eter

NC

Tape x4

14"

Left

Neu

tral 16

"

Rig

htN

eutr

al

3/8"

Loo

m

AB

CNC

NO

Aux

Pow

erO

utle

t11

"

25"

Key

Sw

itch

G S

B

LM

¼"

FI Q

uick

Fe

mal

e x2

LN,R

N,B

rake

1,B

rake

2-H

ousi

ng, P

acka

rd p

/n 2

9770

48. C

onta

cts,

p/n

296

5142

(F/1

4-16

).

Clu

tch

Del

ay-H

ousi

ng, P

acka

rd p

/n 2

9738

72. C

onta

cts,

p/n

296

5142

(F/1

4-16

).

Bla

de-H

ousi

ng, D

elta

Sys

tem

s p/

n 97

2306

. Con

tact

s, P

acka

rd p

/n 2

9651

42(F

/14-

16).

Key

-Hou

sing

, Pac

kard

p/n

029

7342

2. C

onta

cts,

p/n

296

2142

(F/1

4-16

).

F1,F

2,F3

,F4,

-Hou

sing

/Wire

, Bus

sman

n p/

n H

HM

.

Tape

All

Loom

End

s

Con

nect

ors

view

ed fr

om w

ire e

ntry

All

Loom

Mus

t Be

Hig

h Te

mpe

ratu

re Id

entif

ied

With

Str

ipe

NO

TE:

Eng

Gnd

5" 5/16

NI

Rin

gx2

Clu

tch

12"

5"4"

Red

Boo

tB

lack

Boo

t

Tape

Fuel

P

ump10

"

Eng

3

20"

3/16

FI F

em

Qui

cks

Red

Boo

t M

etro

p/n

M23

507

5/16

NI

Rin

gx2

30

8787A

85

86

30

8787A

85

8630

8787A

85

86

30

8787A

85

86

Met

ro p

/n M

2350

1M

etro

p/n

M23

500

Soc

kets

Vie

wed

from

R

elay

Inse

rtio

n!!

!!!!

Bla

deS

witc

hS

plic

e

CR

1,C

R2,

CR

3, C

R4

-Hou

sing

, Bos

ch p

/n 3

3344

8500

8. C

onta

cts,

Am

p p/

n 60

253-

2 (1

6/14

ga).

Eng

3-H

ousi

ng, P

acka

rd p

/n 8

9051

17. C

onta

cts,

p/n

296

2987

(M/1

4-16

).

Clu

tch

-Hou

sing

, Pac

kard

p/n

298

4883

. Con

tact

s, p

/n 2

9629

87.

Eng

6-H

ousi

ng, P

acka

rd p

/n 0

2977

042.

Con

tact

s, p

/n 2

9629

87(M

/14-

16).

F1=

20A

F2=

10A

F3=

10A

F4=

25A

5 =

RE

D /

BLU

E

4 =

RE

D /

BLA

CK

3 =

RE

D

2 =

BLA

CK

1 =

RE

D

9 =

GR

EE

N

7 =

OR

AN

GE

6 =

WH

ITE

/ V

IOLE

T

8 =

OR

AN

GE

/ W

HIT

E

10 =

GR

EE

N /

WH

ITE

11 =

YE

LLO

W /

BLA

CK

16 =

RE

D /

YE

LLO

W

15 =

RE

D /

GR

EE

N

14 =

GR

EE

N /

OR

AN

GE

13 =

WH

ITE

/ B

LUE

12 =

WH

ITE

20 =

BLU

E

18 =

BR

OW

N

17 =

BLA

CK

WH

ITE

19 =

YE

LLO

W

25 =

YE

LLO

W /

WH

ITE

10

+-

+ -

-+

+

-

F2

20F1

Tape

Tape

10 F3

Tape

¼"

FI Q

uick

Fe

mal

e x2

Ove

r-Te

mp

Ala

rm

3/8"

Loo

m

Dia

gnos

ticLa

mp

Oil

Pre

ssur

eLa

mp

3/16

" FI

Qui

ck

Fem

ale

x4

21 =

BLU

E /

RE

D

WIR

E C

OLO

R

MA

TRIX

CO

NN

EC

TOR

, TE

RM

INA

L, F

US

E H

OLD

ER

M

ATR

IX

FUS

E M

ATR

IX

Sea

t

3/8"

Loo

m

4"

2"

5"

2"

Eng

6

5"

3"

Sta

rter

Sol

enoi

dS

tart

er

10"

22 =

BLA

CK

23 =

RE

D

24 =

RE

D /

WH

ITE

¼"

FI Q

uick

Fe

mal

e x2

Tape

# 8

NI R

ing

x2 7"

7"7"

7"

53"

4" x24"

10"

4"

6"7"Ta

pe8"

Clu

tch

Del

ay

+- Tape1"

5/8"

Loo

m

4" x2

Tape

Tape

.156

FI

Fem

ale

Bul

let

25F4

4"

1/2"

Loo

m

4A,N2P,Q

22A

4C,E

,J,L

4B

4M2T

4K

4H

4F,G

Spl

ice

2U,S

2R

4D

2V

4P,Q

4R,S

2F,G

4T,U

2H,J

2K,L

2M,N

4V,W

Spl

ice

2D,E

2A

2C,W

,Y2B

2X

4X22B

++

5/8"

Loo

m

1/4"

Loo

m

3D

1A

5B

Spl

ice

1B3A

3BF4,F

1

5A 3C7"

Tape

1/4

FI F

em

Qui

ck

6A

6B 7A

7B

8A

8B

9A

9B

10A

10B

,C

10D

,E

10F,

G10

H

11A

11B

12A

12B

,C

¼"

FI Q

uick

Fe

mal

e x

2

1"1"

12E

12D

Tape

Tape

D1,

Dio

de

-

12F

13A

13B

14A

14B

15A

15B

16A 16

B

17A

17B

18B

18A

19A

19B

20B

20A

21B

+ -21

A23

A

23B

24A

25B

24B

-+

2Z

25A

26A

26B

,C

26D

,E

26F

+

26 =

GR

AY

Bat

tery

1"


Engine & ElectricalWiring Harness 4

29-61,73 Kawasaki Rev. B.01

F120A

25A

L

B

S

START

CLUTCH

CR1

CR2

CR3

Seat Sw

CR4

Eng3

F3

10A

RectifierRegulator

CR4 Eng3ECU

ECU

brn

Starter/Batt

Eng6 Eng*ECU

Regyel/wht

org

wht

30 87

30 87

30 87

85 86

Fuel Pump

red

red/blu

blk

blk

blk

blk

red/yel

red/grn

red/blk yel

blu

blk/wht

G

B

S

L

M

POSITION FUNCTION CONTACTS123

OFFRUN

START

G & ML & B

L & B & S

Key Switch

3087

Exbullet

Eng6 red

brn

G

M

gry

CR3

START

CR2

CLUTCH

CR1

OP PRESENT

Blade SW

Blade SW

OFF

OFF

Hour Meter

85 86

85 86

85 86

red/blk blk

blk

blk

blk

org/wht grn

grn/org

org

grn/wht

grn/wht

wht/vio

DELAYwht

F2

10A

com B

com C

OFF OFF

grn/wht yel/blk wht

wht/bluBrake1Brake1 Blade SW

OFF

com B

Aux PP

red/blk

red/blk

Seat LN RN

RN LN Brake2

OFF

red blk

D2

Eng Chassis

R

Water Temp

Alarm

Eng6red/blk

Eng6

ECUblkblk

Eng3

ECUredred/blk

Diagnostic

R

Eng6 blu/redred/blkOil Press

red/wht

blu/red

blk

yel/wht yel


Lastec//072815 5-1

5

SECTION 5 61” MOWER DECK

61 in DeckDeck Framework5

5.1 Deck Framework


1 049855 Belt, B-128 Deck Drive 1

2 041645 Grass Chute Assembly 1

3 049490 Deck Weldment, 61” Articulating #3 1

4 049512 Deck Weldment, 61” Center 1

5 055835 Deck Weldment, 61” Articulating #1 Serial # 2850806 and later 1

049532 Deck Weldment, 61” Articulatin #1 Serial # 2849806and prior 1

5-2 Lastec//072815 61 in Deck

61 in DeckDeck Framework 5

LT0042

61 in Deck Lastec//072815 5-3

61 in DeckDeck 1 Hardware (Serial # 2860806 and later)5

5.2 Deck 1 Hardware (Serial # 2860806 and later)


Nut, 5/8-11 FlexLoc

Deck Weldment, 61” Articulating #1

Nut, 3/8-16 Flanged Hex Nyloc

Cover, 61A Deck #1

Spindle Assembly, ZT 21” D6.3-6.3


055834 Deck Assembly, 61” Articulating #1 1

1 F05009-20 2

2 F05010-185 2

3 055835 1

4 F05010-222 3

5 055803 1

6 067695 1

1 Replaces 049892 2861AGC Double Sheave Spindle Assembly (See Section 5.10 for parts) (5/14 and later).

See Section 5.8 for parts 1


61 in DeckDeck 1 Hardware (Serial # 2860806 and later) 5

LT0043B


61 in DeckDeck 1 Hardware (Serial # 2850806 and prior)5

5.3 Deck 1 Hardware (Serial # 2850806 and prior)

NOTE: If using the rear discharge system, items 1,2,3 and 4 are not used.

NOTE: After Serial # 2850806, the rear bolt-on baffle was replaced with a full pan wrap around the deck weldment.



2 F05011-17 Washer, 5/16” SAE Flat 3

3 049781 Baffle, Outside Rear Bolt-On 1

4 F05010-58 Nut, 5/16-18 Nylok Hex 2


6 F05010-185 Nut, 5/8-11 FlexLoc 2

7 049532 Deck Weldment, 61 Articulatin #1 1

8 F05010-10 Nut, 3/8-16 Hex Nyloc Added after serial # 2410406 3

9 F05011-3 Washer, 3/8” Flat SAE Added after serial # 2410406 3

10 055803 Cover, 61A Deck #1 Added after serial # 2410406 1


61 in DeckDeck 1 Hardware (Serial # 2850806 and prior) 5

049535


61 in DeckDeck 2 Hardware5

5.4 Deck 2 Hardware

NOTE: If using the rear discharge system, items 20-25 are not used.

Item 2 and 8: Apply water-proof axle grease to mating surfaces prior to assembly.


1 049512 Deck Weldment, 61” Center 1

2 049870 Bushing, Urethane Pivot 2 Added after Serial #2790806 1

049510 Bushing, Rubber Pivot Serial #2780806 and priorNo longer available; order 049870

1

3 049894 Link, Front Deck Lift 4

4 P110 Pin, 3/8” x 1 5/16” Clevis, Yzn 2


6 F04254-46 Ring, 3/4” External - External 1



9 P212 Pin, 3/8” x 2 1/8” Clevis, Yzn 1



12 062051 Washer, Water Shed Pulley 1

045271 Pulley Assembly, 5” OD Idler, V Groove Serial # 33151108 and later 1

043543 Pulley, 5” OD V-Groove Idler No longer available: order 045271 Serial # 33141108 and prior

1

13 F04254-12 Ring, 62mm IR Din #472 Retaining 2

14 P103 Bearing, Spindle Top 6305 RS 1

15 045270 Pulley, 5” OD Idler, V Groove 1

16 045297 Boss, Idler Pulley Standoff 1

17 049868 Spacer, .53” ID x 1 1/4” OD x 1 1/4” Lng 1

18 F05007-165 Bolt, 3/8-16 x 1” Carriage, Zinc Grade 5 2

19 F05010-222 Nut, 3/8-16 Flanged Hex Nylon Lock 2

20 049784 Baffle, Outside Rear Bolt-On 1


22 F05011-17 Washer, 5/16” SAE Flat 2

23 F05010-58 Nut, 5/16-18 Nylon Lock Hex 1



26 027013 Wheel, Anti-Scalp, 5-5/8" hole 1


28 072497 Spacer, 1 OD x .65 ID x .53 Long 1


30 067695 1


Spindle Assembly, ZT 21” D6.3-6.3 See Section 5.8 for parts 1


61 in DeckDeck 2 Hardware 5


LT0030B



5.5 Deck 3 Hardware


Nut, 5/16-18 Flanged Nylok Hex


Baffle, Outside Rear Bolt-On


Nut, 5/8-11 FlexLoc

Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Grade 5


Cover, 61A Deck #3


Grass Chute Assembly


NOTE: If using the rear discharge system, items 1,2,3 and 4 are not used.



1 F05011-17 2

2 F05010-221 2

3 F05006-27 1

4 049781 1

5 F05009-20 2

6 F05010-185 2

7 F05006-93 1

8 049490 1

9 055804 1

10 F05010-222 3

11 041645 See Section 5.13 for parts 1

12 067695 1





LT0044-1B


61 in DeckRear Discharge Baffle Assembly5

5.6 Rear Discharge Baffle Assembly

Baffle Assembly, #3 Deck Mulching

Nut, 3/8-16 Flanged Hex Nyl Lock

Baffle Weldment, #3 Deck Mulching

Bolt, 3/8-16 x 1” Carriage Grade 5


Baffle Assembly, #2 Deck Rear Discharge

Baffle Weldment, #2 Deck Rear Discharge

Nut, 3/8-16 Flanged Hex Nyl Lock


NOTE: To use the rear discharge system, bolt in the rear discharge baffle weldments as shown here, and remove the factory installed rear baffle plates from decks 2 and 3. The factory installed baffle remains on deck 1.

NOTE: All units receive the rear discharge baffles -- use of the rear discharge system is optional. Rear Chute is only for use with units with serial # 2850806 and prior.


049997 Baffle Kit, Rear Discharge 1

049963 1

1 F05010-222 2

2 049873 1

3 F05007-165 1

4 F05007-85 1

049961 1

5 049960 1

6 F05010-222 3

7 F05007-165 3

8 055452 Kit, Rear Discharge Chute Serial # 2850806 and prior 1


61 in DeckRear Discharge Baffle Assembly 5

LT0048B

Factory installedBaffle removed

Factory installed Baffle removed

Factory installedBaffle remains


61 in DeckOptional Mulching Kit5

5.7 Optional Mulching Kit

This mulching kit may be purchased through your Lastec Dealer.

To properly use the mulching feature, the Deck 3 Baffle 049963 from the rear dischargekit must also be in place. The 049963 Deck 3 Baffle Includes the unit in a separate box aspart of the Rear Discharge Baffle Assembly. All factory installed rear baffles remain inplace for mulching.


049998 Baffle Kit, Mulching 61AGC 1

049962 Baffle Assembly, #2 Deck Mulching 1


2 049877 Baffle Weldment, #2 Deck Mulching 1

3 F05007-165 Bolt, 3/8-16 x 1” Carriage Grade 5 3

049964 Baffle Assembly, #1 Deck Mulching 1

4 049866 Baffle Weldment, #1 Deck Mulching 1


6 F05007-165 Bolt, 3/8-16 x 1” Carriage Grade 5 2

7 P322 Blade, 21” Gator Mulching 3


61 in DeckOptional Mulching Kit 5

LT0047C


Mower DecksDouble Pulley Spindle (5/14 and later)5

5.8 Double Pulley Spindle (5/14 and later)


Bolt, Spindle Single Pulley

Washer, 1/2” Plain Belleville

Key, 1/4” Square x 1 1/2” Long

Sheave, Double - Mower Deck


Spindle Assembly, ZT Cast


Blade, 21” x 2 1/2” x 1/4” High Lift

Blade, 21” Low-Lift

Blade, 21” Gator Mulching

Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra

Washer, 2 1/2” x 11/16” x 3/16” Nylon

Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat



067695 Spindle Assembly, ZT 21” D6.3-6.3 Non-saleable item. Parts must be purchased separately.

1

1 P107 1

1 For service order 067354 Spindle Bolt 1 1/4” Service Kit including (1) P107 1/4-28 Straight Grease Fitting and (1) 045677 Spindle Single Pulley Bolt.

1

2 0456771 Maximum Torque: 57 ft-lbs 1

3 F05011-97 1

4 028080 1

5 067688 1

6 F05007-78 4


8 F05010-222 4

9 P128 1

P246 Optional 1

P322 Optional 1

063265 Optional 1

10 029889 1

11 F05011-89 Remove to install Anti-Scalp Blade Disc

1

12 F05009-95 Torque Value: 75 ft-lbs 1

13 048898 Blade Disc, Anti-Scalp Optional part. Remove Item 11 to install Anti-Scalp Blade Disc

1


Mower DecksDouble Pulley Spindle (5/14 and later) 5

100_190


Mower DecksSpindle Housing5

5.9 Spindle Housing

Bearing, 6206-2NSE

O-Ring, 2 1/2” ID x 2 3/4” OD

Spacer, Bearing Housing

Spindle Housing, ZT- Common Core

Spacer, Spindle Bearing Housing

Washer, 1.50” x 1.185” x 16Ga

Washer, 2.435” x 1.185” x 11Ga

Shaft, Blade Spindle ZT Cast

Concerning Nachi Sealed Bearings:

One of the most common misconceptions that cause a high number of bearing failures is that a bearing needs to be completely packed full. Many people have been taught; the more grease, the better. We have even heard of cases where people do not feel bearing manufacturers use enough grease in sealed and shielded ball bearings, so they remove one seal or shield and pack the bearing with more grease. These misconceptions are completely false. Over lubri-cating the bearings forces the motor to work harder.

Nachi standard grease fill for sealed and shielded ball bearings is 20% to 30% full

Too much grease can cause excess friction, thereby overheating the bearing and causing remature failure.

Only a small of grease is required to lubricate a bearing in motion.

When a bearing is in motion, most of the grease is pushed to the side (channeling) leaving a thin film of oil between the raceways and rolling elements.

When using open bearings, pack the bearing as follows:


067696 Spindle Assembly, Center w/Stiffener Non-saleable item. Parts must be purchased separately.

1

1 P11035 3

2 P105 4

3 072511 1

4 067999 1

5 067686 1

6 034947 1

7 034948 1

8 067687 1


Mower DecksSpindle Housing 5

100_188


61 in DeckDouble Pulley Spindle (Prior to 5/14)5

5.10 Double Pulley Spindle (Prior to 5/14)

Fitting, 3/16” x 3/16” Straight Grease



Key, 1/4” x 2 1/2”

Sheave, Double - 2561 Mower

Washer, 1/4” x 1.47” x 1.01”


Plate, Deck Reinforcing


Spindle Assembly, Center w/Stiffener



Blade, 21” Low-Lift

Blade, 21” Gator Mulching


Washer, 2 1/2” x 11/16” x 3/16” Nylon

Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat




049892 Spindle Assembly, 2861AGC Double Sheave Non-saleable item. Parts must be purchased separately.

1

1 P04107 1


3 F05011-97 1

4 027053 1

5 040049 1

6 046273 1

7 F05007-85 4

8 044862 Serial # 2940906 and later 2

048183 Serial # 2930806 and prior 1


10 F05010-10 4

11 P128 1

P246 Optional 1

P322 Optional 1

063265 Optional 1

12 029889 1

13 F05011-89 Serial # 2940906 and later. Remove to install Anti-Scalp Blade Disc

1

F05011-27 Serial # 2930806 and prior 1



1


61 in DeckDouble Pulley Spindle (Prior to 5/14) 5

LT0033


61 in DeckSpindle Housing5

5.11 Spindle Housing


Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5



Seal, 2561 Spindle

Collar, Spindle Top

O-Ring, Spindle

Bearing, 6206-2NSE

Housing, Spindle

Pin, 1/8” x 1/2” Roll

Nut, 5/16-18 Nylon Lock Hex

Spacer, Spindle Bearing

O-Ring, 2 7/16" ID x 3/16" Diameter

Washer, 1.50” x 1.185” x 16Ga

Washer, 2.435” x 1.185” x 11Ga

Shaft, Center Blade Spindle










1

1 F05006-140 Added after serial # 33351208 3

2 F05006-93 3 deleted after serial # 33341208 3


4 034921 1

5 034969 1

6 034951 1

7 062999 Added after serial # 34990809 1

8 P11035 3

9 034945 1

10 F05012-64 1


12 034950 1

13 F04254-45 2

14 034947 1

15 034948 1

16 043245 1


61 in DeckSpindle Housing 5

LT0024B


61 in DeckTensioner Assembly5

5.12 Tensioner Assembly




Pulley, 5” OD Idler, Flat

Pulley, 5” OD Idler


049797 Idler Assembly, Deck Drive 1

1 F05010-222 Nut, 3/8-16 Flanged Hex Nyloc 1

2 F05010-1 Nut, 3/8-16 Hex 1

3 034982 Spring, 1 1/2” OD x 8 1/2” x .195” 1



6 047878 Idler Pivot Weldment 1



045295 Pulley Assembly, 5” OD Idler, Flat 1

9 045297 1

10 F04254-12 2

11 P103 1

12 045296 Serial # 33151108 and later 1

043367 Serial # 33141108 and prior 1


14 F05010-223 Nut, 1/2-13 Flanged Nylon Hex Lock 1

15 F05011-104 Washer, 3/8 x 1-1/2 x 1/8 Thick Hardened 1


61 in DeckTensioner Assembly 5

LT0029B


61 in DeckGrass Chute5

5.13 Grass Chute


Spring, Deere RH Torsion

Grass Chute, John Deere

Bolt, 5/16-18 x 9” Hex Head Grade 5 Spcl


041645 Grass Chute Assembly 1

1 F05010-58 1

2 041714 1

3 041572 1

4 F05006-110 1


61 in DeckGrass Chute 5

LT0044-2B


61 in DeckRear Anti-scalp Roller (Prior to 5/14)5

5.14 Rear Anti-scalp Roller (Prior to 5/14)


Plate, Anti-Scalp Adjusting


Mount Weldment, Deck Anti-Scalp

Nut, 5/8-11 FlexLoc

Nut, 5/8-11 Jam


Bushing, Urethane Pivot

Nut, 5/8-11 Jam Nylon Lock

Wheel, Anti-Scalp, 5 5/8" hole


NOTE: Lubricate all surfaces of the inner bushing (049870) with a water-proof axle grease prior to assembly.



049795 Wheel Assembly, Deck Anti-Scalp 1

1 F05010-10 2

2 063201 1

1 Replaced Deck Lift Link Rod Assembly (046700) on units with serial #34660609 and later. NOTE: 063201 is retrofittable to all units produced to date. 046700 does not work on units with serial #34660609 and later.

1

3 F05007-123 2

4 049794 1

5 F05010-185 1

6 F05010-82 1

7 F05009-35 1

8 049870 1

9 F05010-96 1

10 027013 1

11 F05009-28 1


61 in DeckRear Anti-scalp Roller (Prior to 5/14) 5

LT0046


Lastec//072815 6-1

6

SECTION 6 73” MOWER DECK

73 in DeckDeck Framework6

6.1 Deck Framework


1 048272 Belt, 72" Deck Drive 1

2 041645 Grass Chute Assembly 1

3 044632 Deck Weldment, 73 Articulating #3 1




73 in DeckDeck Framework 6

LT0049



6.2 Deck 1 Hardware


Nut, 5/8-11 FlexLoc


Nut, 3/8-16 Flanged Hex Nylock

Cover, 61A Deck #1





1 F05009-35 1

2 F05010-185 2

3 044630 1

4 F05010-222 3

5 055803 1

6 F05009-20 1

7 067694 1

1 Replaced 055444 73” Double Sheave Spindle Assembly (See Section 6.7) to improve durability (8/14).




LT0050B



6.3 Deck 2 Hardware



1 044631 Deck Weldment, 73” Articulating #2 Gas 1

2 049870 1

1 Lubricate all mating surfaces of Urethane Pivot Bushing (049870) with a water-proof axle grease prior to assembly.

Bushing, Urethane Pivot 6

048890 Plate Assembly, Deck Adjusting 2

3 055192 Bolt Weldment, Height Adjust Eye 1

4 F05010-29 Nut, 3/8-16 Jam 1

5 062950 Adjusting Weldment, Deck 1

6 P110 Pin, 3/8” x 1 5/16” Clevis, Yzn 2


8 F04254-46 Ring, 3/4” External - External 1


10 049894 Link, Front Deck Lift 2

11 P212 Pin, 3/8” x 2 1/8” Clevis, Yzn 1



048452 Pulley, 9” B-C Groove Idler 1

14 F04254-4 Ring, 1.575” ID 3000-156 Retaining Available with Pulley Only 1

15 P06030-2 Bearing, 6203-2NSL 17mm SRI-2 ABEC-1 Available with Pulley Only 1

16 048451 Pulley Weldment, 9“ Idler Available with Pulley Only 1

17 048453 Adapter, Idler Pulley Bore Available with Pulley Only 1

18 055405 Spacer, 73” Deck 1/2ID x 1-3/8 1


20 F05010-10 Nut, 3/8-16 Hex Nylon Lock 2

21 F05007-165 Bolt, 3/8-16 x 1” Carriage, Zinc Grade 5 2

22 055424 Baffle Weldment, 73” #2 Deck 1


24 F05010-1 Nut, 3/8-16 Hex 1

25 F05011-104 Washer, 3/8” x 1-1/2” x 1/8” Thick Hardened 1

26 027013 Wheel, Anti-Scalp 5-5/8" Hole 1


28 072497 Spacer, 1 OD x .65 ID x .53 Long 1


30 072486 Spindle Assembly, 73” Gas Double Sheave See Section 6.10 1



LT0032B



6.4 Deck 3 Hardware


Cover, 61A Deck #3



Nut, 5/8-11 FlexLoc


Baffle Assembly, #3 Deck Mulching 73”



Baffle Weldment, #3 Deck Mulching 73”


Grass Chute Assembly




1 F05010-222 3

2 055804 1

3 044632 1

4 F05009-20 1

5 F05010-185 2

6 F05009-35 1

055890 1

7 F05007-85 1

8 F05010-222 2

9 055891 1

10 F05007-165 1


12 067694 1

1 Replaced 055444 73” Double Sheave Spindle Assembly (See Section 6.7) to improve durability (8/14).




LT0051B


Mower DecksDouble Pulley Spindle, Decks 1 and 3 (8/14 and later)6

6.5 Double Pulley Spindle, Decks 1 and 3 (8/14 and later)




Key, 1/4” Square x 1 1/2” Long

Sheave, Double - Mower Deck





Blade, 25” x 2 1/2” x 1/4” Low Lift

Blade, 25" Gator Mulching


Washer, 2 1/2” x 11/16” x 3/16” Nylon

Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc



067694 Spindle Assembly, ZT 25” D6.3-6.3 Non-saleable item. Parts must be purchased separately.

1

1 P107 1


3 F05011-97 1

4 028080 1

5 067688 1

6 F05007-78 4


8 F05010-222 4

9 P701 1

P849 Optional 1

P848 Optional 1

063266 Optional 1

10 029889 1


1



1


Mower DecksDouble Pulley Spindle, Decks 1 and 3 (8/14 and later) 6

120_085


Mower DecksSpindle Housing, Decks 1 and 3 (8/14 and later)6

6.6 Spindle Housing, Decks 1 and 3 (8/14 and later)

Bearing, 6206-2NSE

O-Ring, 2 1/2” ID x 2 3/4” OD

Spacer, Bearing Housing

Spindle Housing, ZT- Common Core

Spacer, Spindle Bearing Housing

Washer, 1.50” x 1.185” x 16Ga

Washer, 2.435” x 1.185” x 11Ga

Shaft, Blade Spindle ZT Cast










1

1 P11035 3

2 P105 4

3 072511 1

4 067999 1

5 067686 1

6 034947 1

7 034948 1

8 067687 1


Mower DecksSpindle Housing, Decks 1 and 3 (8/14 and later) 6

100_188


73 in DeckDouble Pulley Spindle, Decks 1 and 3 (Prior to 8/14)6

6.7 Double Pulley Spindle, Decks 1 and 3 (Prior to 8/14)




Key, 1/4” x 2-1/2”

Sheave, Double - 2561 Mower

Washer, 1.50” x 1.185 x 16Ga

Washer, 3/8” x 1.5 x 1.01”

Bolt, 3/8-16 x 1 1/2” Carriage Gr5






Blade, 25” x 2 1/2” x 1/4” Low Lift

Blade, 25" Gator Mulching


Washer, 2-1/2” x 11/16” x 3/16” Nylon

Washer,2 1/2” OD x 5/8” ID x 3/16” Std Flat Znc




055444 Spindle Assembly, 73” Double Sheave Non-saleable item. Parts must be purchased separately.

1

1 P107 1

1 P107 replaced P04107 3/16” x 3/16” Straight Grease Fitting to improve durability (Serial #41071011 and later).

1


3 F05011-97 1

4 027053 1

5 040049 1

6 034947 1

7 043249 1

8 F05007-85 4

9 044862 Serial # 2940906 and later 2

048183 Serial # 2930806 and prior 1


11 F05010-10 4

12 P701 1

P849 Optional 1

P848 Optional 1

063266 Optional 1

13 029889 1

14 F05011-89 Serial # 2940906 and later.Remove to install Anti-Scalp Blade Disc

1

F05011-27 Serial # 2930806 and prior 1



1


73 in DeckDouble Pulley Spindle, Decks 1 and 3 (Prior to 8/14) 6

LT0137


73 in DeckSpindle Housing6

6.8 Spindle Housing


Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread Gr5



Seal, 2561 Spindle

Collar, Spindle Top

O-Ring, Spindle

Bearing, 6206-2NSE

Housing, Spindle

Pin, 1/8” x 1/2” Roll

Nut, 5/16-18 Nylon Lock Hex

Spacer, Spindle Bearing

O-Ring, 2 7/16" ID x 3/16" Diameter

Washer, 1.50” x 1.185” x 16Ga

Washer, 2.435” x 1.185” x 11Ga

Shaft, Center Blade Spindle










1




4 034921 1

5 034969 1

6 034951 1

7 062999 Added after serial # 34990809 1

8 P11035 3

9 034945 1

10 F05012-64 1


12 034950 1

13 F04254-45 2

14 034947 1

15 034948 1

16 043245 1


73 in DeckSpindle Housing 6

LT0024B


73 in DeckTensioner Assembly6

6.9 Tensioner Assembly



Pulley, 5” OD Idler, Flat

Pulley, 5” OD Idler



055428 Idler Assembly, 73” Deck Drive 1



045295 Pulley Assembly, 5” OD Idler, Flat 1

3 F04254-12 2

4 P103 1

5 045296 Serial # 33151108 and later 1

043367 Serial # 33141108 and prior 1

6 045297 1

7 055429 Idler Weldment, 73” Deck Drive 1





12 F05011-104 Washer, 3/8” x 1 1/2” x 1/8” Thk Hardened 1

13 034982 Spring, 1 1/2” OD x 8 1/2” x .195” 1

14 F05010-1 Nut, 3/8-16 Hex 1



17 019650 Spacer, 1/4” Thk Deck Height 2


73 in DeckTensioner Assembly 6

LT0031B


73 in DeckDeck 2, Double Pulley Drive Spindle (8/14 and later)6

6.10 Deck 2, Double Pulley Drive Spindle (8/14 and later)




Key, 1/4” x 1-1/2”

Sheave, Double - D7.0-6.3



Nut, 3/8-16 Flanged Hex Nylon Lock

Blade, 25” x 2-1/2” x 1/4” High Lift

Washer, 2 1/2” x 11/16” x 3/16” Nylon




072486 Spindle Assembly, 73” Gas Double Sheave 1

1 P107 1

2 045677 Maximum Torque: 57 ft.lbs 1

3 F05011-97 1

4 028080 1

5 073389 1

1 Replaced 072492 73” Double Sheave (Serial #54410615 and later).

1

6 F05007-78 4


8 F05010-222 4

9 P107 1

10 029889 1


1

12 F05009-95 Torque Value: 75 ft.lbs 1


1


73 in DeckDeck 2, Double Pulley Drive Spindle (8/14 and later) 6

LT0149B


73 in DeckDeck 2, Double Pulley Drive Spindle (Prior to 8/14)6

6.11 Deck 2, Double Pulley Drive Spindle (Prior to 8/14)




Key, 1/4” x 2-1/2”

Sheave, Double 73 Mower

Washer, 1.50” x 1.185” x 16Ga

Washer, 3/8” x 1.5” x 1.01”

Bolt, 3/8-16 x 1 1/2” Carriage Gr5



Nut, 3/8-16 Hex Nylon Lock

Blade, 25” x 2-1/2” x 1/4” Low Lift

Washer, 2 1/2” x 11/16” x 3/16” Nylon




055427 Spindle Assembly, 73” Gas Double Sheave 1

1 P107 1

1 P107 replaced P04107 3/16” x 3/16” Straight Grease Fitting to improve durability (Serial #41071011 and later).

1

2 045677 Maximum Torque: 57 ft.lbs 1

3 F05011-97 1

4 027053 1

5 055395 1

6 034947 1

7 043249 1

8 F05007-85 4

9 044862 2


11 F05010-10 4

12 P849 1

13 029889 1


1

15 F05009-95 Torque Value: 75 ft.lbs 1


1


73 in DeckDeck 2, Double Pulley Drive Spindle (Prior to 8/14) 6

LT0034


73 in DeckGrass Chute6

6.12 Grass Chute


Spring, Deere RH Torsion

Grass Chute, John Deere

Bolt, 5/16-18 x 9” Hex Head Grade 5 Spcl


041645 Grass Chute Assembly 1

1 F05010-58 1

2 041714 1

3 041572 1

4 F05006-110 1


73 in DeckGrass Chute 6

LT0044-2B


73 in DeckRear Anti-scalp Roller (Prior to 8/14)6

6.13 Rear Anti-scalp Roller (Prior to 8/14)


Plate, Anti-Scalp Adjusting


Mount Weldment, Deck Anti-Scalp

Nut, 5/8-11 FlexLoc

Nut, 5/8-11 Jam


Bushing, Urethane Pivot

Nut, 5/8-11 Jam Nylon Lock

Wheel, Anti-Scalp, 5 5/8" hole


NOTE: Lubricate all surfaces of the inner bushing (049870) with a water-proof axle grease prior to assembly.



049795 Wheel Assembly, Deck Anti-Scalp 1

1 F05010-10 2

2 063201 1

1 Replaced Deck Lift Link Rod Assembly (046700) on units with serial #34660609 and later. NOTE: 063201 is retrofittable to all units produced to date. 046700 does not work on units with serial #34660609 and later.

1

3 F05007-123 2

4 049794 1

5 F05010-185 1

6 F05010-82 1

7 F05009-35 1

8 049870 1

9 F05010-96 1

10 027013 1

11 F05009-28 1


73 in DeckRear Anti-scalp Roller (Prior to 8/14) 6

LT0046


Mower//072815 7-1

7

SECTION 7 INDEX

Part Number Index

014419 , Decal, Hot Engine Warning 1-4, 1-6014815, Rod End, 5/16-24 Male LH 2-24, 3-6014818, Spring, Extension 3/8” x 3” 2-2014834, Bearing, w/Snap Ring 5/8” ID 2-24015485, Fitting, 3/8” Barb Tee 3-4018739, Rod End, 3/8-24 Right Hand 2-24, 2-38, 3-6018740, Rod End 3/8-24 Left Hand 2-32, 2-34, 2-38018773, Sheave, BK60 QT 3-6019086, Knob, 1 3/8” x 3/8-24 2-30019086, Knob, 1 3/8” x 3/8-24 2-26019094, Plate, Drive Motor Mount 2-44019298, Hose, Fuel, 1/4” x 8”, 325E98 4-6019359, Bushing, 15mm Split Taper 3-6019552, Decal, Caution Clean Radiator 1-4, 1-6019554 , Decal, Warning, Operational Safety 425D 1-4,

1-6019557, Decal, Articulator Logo Div WM 1-4, 1-6019650, Spacer, 1/4” Thk Deck Height 6-18019696, Cap, Hyd Tank (P631) 4-2, 4-4023541, Bearing, 1” Flanged Mount 2-44024155, Clamp, 1/4" Wire 13/32” Mtg Hole 2-2024155, Clamp, 1/4” Wire 13/32 Mtg Hole 2-40026371, Spring, 1 3/8" x 15.8” x .187” Extension 2-38026382, Angle, Battery Hold Down 4-20026396, Spacer, Clutch 4-10026399, Spacer, Hydro Actuator 3-6026407, Plate Weldment, E-Brake Lock 2-36026409, Pulley, E-Brake 2-36, 3-8, 3-10026412, Rod Weldment, E-Brake Tensioner 2-36026416, Cable E-Brake 2-36026417, Hex Nut, 1-20 Slotted 3-8, 3-10026439, Tire Assembly, 24” x 12-12 Turf Master 3-8,

3-10026440, Rim, 12” x 8 1/2” 8 Spoke 4 1/2” BC 3-8, 3-10026443, Block, Spring Tensioner 2-38026446, Rod Wldmnt, Spring Tensioner 2-38026447, Turnbuckle, Deck Lift 2-38026448, Turnbuckle Assembly, Deck Lift 2-38026470, Belt, BX54 3-6026472, Tensioner Bushing 4-16027006, Spring, 1-1/8" x 7-1/2" x .091 Extension 4-8027009, Guard, Right Hydro Fan 4-14027013, Wheel, Anti-Scalp 5-5/8" hole 2-18027013, Wheel, Anti-Scalp 5-5/8" hole 6-6027013, Wheel, Anti-Scalp, 5-5/8" hole 5-8, 5-28, 6-26027015, Arm Weldment, 2561 Right Control 2-24027016, Arm Weldment, 2561 Left Control 2-24027053, Key, 1/4” x 2 1/2” 5-20027053, Key, 1/4” x 2-1/2” 6-14, 6-22

027056, Plate, E-Brake Pulley Right 3-8027057, Plate, E-brake Pulley Left 3-10027066, Hose, 2561 Oil Drain 3-14, 3-16028072, Fitting, 3/8” NPT Street Tee 3-16028080, Key, 1/4” Square x 1 1/2” Long 5-16, 6-10028080, Key, 1/4” x 1-1/2” 6-20028352, Clamp,1” ID Coated 4-20028390, Grip, Handle 2-24028492, Plug, 3/8” NPT Hex Brass 3-16028493, Fitting, 3/8” NPT F-M-F Tee 3-16028535, Oil, Shell TTF-SB 3-2, 3-4028593, Clamp. 3/4” EMY Coated 3-14, 3-16028601, Decal, Fwd/Rev Motion 1-4, 1-6028603, Decal, Brake Control 1-4, 1-6028818, Grommet, Fuel Tank Fitting 4-2, 4-4029109, Spacer, 3/16” Thk Deck Height 2-44029214, Spacer, 1.00” OD x .41” ID x 1/4” Thk Ny-

lon-Blk 2-36029331, Sheave, BK60 1 1/8” 4-10029354, Block, E-Brake Pivot 2-36029360, Handle Weldment, E-Brake 2-36029397, Rod Weldment, Brake Actuator 2-36029842, Bushing, 3/4” ID x 1” OD x 1” Oil 2-28, 2-44,

5-24, 6-18029889, Washer, 2 1/2” x 11/16” x 3/16” Nylon 5-16,

5-20, 6-10, 6-20, 6-22029889, Washer, 2-1/2” x 11/16” x 3/16” Nylon 6-14034921, Plate, Deck Reinforcing 5-22, 6-16034930, Plate Weldment, Deck Height Adjustment 2-32034945, Housing, Spindle 5-22, 6-16034947, Washer, 1.50 x 1.185 x 16Ga 6-16034947, Washer, 1.50” x 1.185 x 16Ga 6-14034947, Washer, 1.50” x 1.185” x 16Ga 5-18, 5-22,

6-12, 6-22034948, Washer, 2.435 x 1.185 x 11Ga 6-16034948, Washer, 2.435” x 1.185” x 11Ga 5-18, 5-22,

6-12034950, Spacer, Spindle Bearing 5-22, 6-16034951, Collar, Spindle Top 5-22, 6-16034969, Seal, 2561 Spindle 5-22, 6-16034982, Spring, 1 1/2” OD x 8 1/2” x .195” 5-24, 6-18040049, Sheave, Double - 2561 Mower 5-20, 6-14040256, Decal, Warning, Outer Decks -- German 1-6040257, Decal, Warning, Outer Decks -- French 1-6040258, Decal, Warning, Outer Decks -- Italian 1-6040259, Decal, Warning, Outer Decks -- Spanish 1-6040260, Decal, Warning, Outer Decks -- Danish 1-6040267, Decal Kit, European Languages 1-6040311, Clutch, 5.75 Dia x 1-1/8 Bore 12V 4-10

2 Lastec//072815 Index

Part Number Index

040338, Stop Weldment, Clutch 4-10040388, Hose, Fuel 1/4” x 32" 4-6040630, Decal, Hydraulic TTF-SB Oil 3-2, 3-4040635, Black Cap, for 32 oz. Bottle Oil Container 3-2,

3-4040636, Bottle, 32 oz. Container for Oil 3-2, 3-4040637, Spout Cap/ W Red Seal for 32 oz. Container 3-2040637, Spout Cap/ W Red Seal for 32oz Container 3-4040642, Oil,TTF-SB 32 oz. Bottle Hydro 3-2040642, Oil,TTF-SB 32oz Bottle Hydro 3-4040910, Decal, Warning Operate From Seat 1-4, 1-6040911, Decal, Warning Operate With Guards 1-4, 1-6040912 , Decal, Danger, Thrown Objects/Arrow 1-4, 1-6041083, Valve, Two Tank Diverter 3-14, 3-16, 4-6041098-1, Tire, 24” x 12-12 (Tire Only) 3-8, 3-10041180, Hose Assembly, 26” OAL x 1/2” Hyd 3-4041200 , Decal, Fuel Switch 421D 1-4, 1-6041205, Decal, Thrown Objects CE Std 1-7041206, Decal, Caution Symbol CE Std 1-7041209, Decal, Keep Away/Rotating Drive Line CE 1-7041572, Grass Chute, John Deere 5-26, 6-24041645, Grass Chute Assembly 5-2, 5-10, 5-26, 6-2,

6-8, 6-24041669, Socket, 12V Accessory Panel Mount 2-26041714, Spring, Deere RH Torsion 5-26, 6-24042003 , Decal, Warning, Slope 1-4, 1-6042942 , Strap, Rubber Pad Mounting 2-46042943, Plate, Mount Washer 2-46042945 , Pad, Rubber Striping 2-46042947, Striping Kit, Commercial Mower 2-46042949 , Plate Weldment, Hanger Strap 2-46042950, Bracket Wldmnt, Right Striping Kit 2-46042951, Bracket Wldmnt, Left Striping Kit 2-46042985, Plate Weldment, Battery Tray 4-20043225, Decal, Flat World Logo 1-4, 1-6043245, Shaft, Center Blade Spindle 5-22, 6-16043246, Spindle Assembly, Center w/Stiffener 5-20,

5-22, 6-14, 6-16, 6-22043249, Washer, 3/8” x 1.5 x 1.01” 6-14043249, Washer, 3/8” x 1.5” x 1.01” 6-22043251, Bushing, Hex, 3/4” x 3/8” 3-14, 3-16043285, Spring, .72” x 2.75” x .105” MW 2-6043285, Spring, 0.72” x 2.75” x 0.105” MW 2-8, 2-10043320, Brake Assembly, 3377TZ Rear Drum 3-8, 3-10043320, Brake Assembly, Rear Drum 3-12043320-1, Drum, 152.4mm w/Studs 3-8, 3-10, 3-12043320-10, Spring, 152.4 x 25 Brake Return 3-12043320-2, Brake, 152.4 x 25 Cam 3-8, 3-10, 3-12043320-4, Stud, 1/2-20 x 1-1/4 Press In 3-12

043320-5, Arm, 152.4 x 25 Brake Actuator 3-12043320-6, Clip, 152.4 x 25 Retainer 3-12043320-7, Backing Plate, 152.4 x 25 Brake 3-12043320-8, Cam, 152.4 x 25 Brake 3-12043320-9, Shoe, 152.4 x 25 Brake 3-12043367, Pulley, 5” OD Idler 5-24, 6-18043441, Washer, Fuel Tank Retaining 4-2, 4-4043442, Washer, Fuel Tank Double 4-2, 4-4043459, Switch, DPST NO 5A Plunger 2-40043543, Pulley, 5” OD V-Groove Idler 5-8043950, Block, Drive Handle Mount 2-24043952, Arm Pivot Weldment, Right Control 2-24043956, Clamp, Blade Switch Mount 2-26043968, Spacer, Wheel Yoke Bearing 2-20044020, Cover, Handle Lockout Switch Right 2-40044021, Cover, Handle Lockout Switch Left 2-40044588, Switch, Blade Start/Stop 2-26044630, Deck Weldment, 73 Articulating #1 6-2044630, Deck Weldment, 73” Articulating #1 6-4044631, Deck Weldment, 73 Articulating #2 6-2044631, Deck Weldment, 73” Articulating #2 Gas 6-6044632, Deck Weldment, 73 Articulating #3 6-2044632, Deck Weldment, 73” Articulating #3 6-8044683, Hose, Clutch Stop Bushing 4-10044696, Tray Assembly, Commercial Battery 4-20044715, Handle Weldmnt, Throttle 2-26044731, Decal, Control Box Engine Throttle 1-4, 1-6044833, Guard Assembly, AC Series 4-8044835, Guard Weldment, AC Series 4-8044862, Plate, Deck Reinforcing 5-20, 6-14, 6-22045270, Pulley, 5 OD Idler, V Groove 4-14045270, Pulley, 5” OD Idler, V Groove 4-16, 5-8045271, Pulley Assembly, 5” OD Idler, V Groove 4-14,

4-16, 5-8045272, Boss, Idler Pulley Standoff 4-14, 4-16045295 , Pulley Assembly, 5” OD Idler, Flat 5-24045295, Pulley Assembly, 5” OD Idler, Flat 6-18045296, Pulley, 5” OD Idler, Flat 5-24, 6-18045297, Boss, Idler Pulley Standoff 5-8, 5-24, 6-18045320, Hose, Fuel 1/4” x 36” 4-6045328, Hose, Fuel 1/4” x 20” 4-6045519, Decal, Sound Power Level 1-4, 1-6045585, Hose, Fuel 1/4” x 14” 4-6045588, Hose, 1/4” x 16” Fuel 4-6045677, Bolt, Spindle Single Pulley 5-16, 5-20, 6-10,

6-14, 6-20, 6-22045693, Key, Ignition 2-26045897, Plate, Decal Fuel 4-2, 4-4045970, Hose, 3/8” Hyd x 3 1/4” Low Pressure 3-4

Index Lastec//072815 3

Part Number Index

045972, Hose, 3/8” Hyd x 9 1/2” Low Pressure 3-4045972, Hose, 3/8” Hyd x 9 5/8” Low Press. 3-16045973, Tank Assembly, Gasoline Dual Fittings 4-4045986, Wheel Assembly, 13” x 6.5” x 6” 2-20, 2-22045988, Cable, Seat Lanyard 2-2045990, Hose Assembly, 1/2 x 15 1/2” JIC 3-4046122, Switch, Ignition Key 2-26046125, Engine Assembly, 29HP 4-10046126, Engine, Kawasaki 29HP 4-10046129, Hour Meter, Digital LCD 2-26046143, Bushing, Clutch Spacer 4-10046144, Pulley, 5” OD Idler 3-18046236, Handle Weldment, Throttle 2-30046239, Washer, Throttle Friction 2-26, 2-30046240, Clamp, Throttle Conduit 2-30046251, Washer Plate, Throttle Friction 2-26, 2-30046270, Rod Weldment, Cowling Pivot 4-12046273, Washer, 1/4” x 1.47” x 1.01” 5-20046293, Washer, Throttle Friction 2-26, 2-30046477, Wheel Yoke Assembly, 13” Comm 2-8, 2-10,

2-20, 2-40046478, Yoke Weldment, 2561 Front Wheel 2-20046534, Mount, Spring 2-38046552, Housing Cap, Kohler Filter 4-18046553, Air Filter, Primary Element 4-18046554, Air Filter, Inner Element 4-18046556, Hood, Rain 4-18046559, Switch, DPST N/O N/C 2-40046659, Motor, Right Hydro-Gear Drive 3-8046661, Motor, Hydro Gear 3-10046668, Cowling Weldment, 29HP Engine 4-12046719, Radiator Cowling Assembly 4-10, 4-12046739, Spring, Cowling Hinge 4-12046760, Valve, Oil Drain 4-10046761, Fuel Pump 4-6046762, Filter, Fuel 1/4” 4-6046764, Bracket, Fuel Pump Bottom 4-6046765, Fuel Pump Module 4-6046767, Grommet, Fuel Pump Mount 4-6046768, Spacer, Fuel Pump Mount 4-6046769, Strap, Fuel Pump Mount 4-60467701, Fuel Pump Assembly, 29Hp 4-6046771, Hose, Fuel 1/2” x 2-1/4” 4-6046772, Adapter, Fuel Hose Reducer 4-6046780, Housing, Engine Air Filter 4-18046781, Bushing, Clamp Spring 4-18046782, Spring, Filter Clamp 4-18046783, Air Filter Assembly 4-18046783, Air Intake Assembly 4-10

046785, Bracket, Upper 4-18046786, Filter Bracket Weldment 4-18046787, Duct, Upper 4-18046788, Pipe, Intake 4-18046789, Filter Assembly, Engine Air 4-18046800, Key, 5/16” x 1” Woodruff 3-8, 3-10046820, Actuator Kit, RTN Std for Model 2861 3-6047187, Spacer, 5/8” x 1” x 5/8” 2-32047234, Spring, .72 x 2.75 x .095 Dia SS Comp 2-32047234, Spring, .72” x 2.75” x .095” Dia SS Comp 2-40047234, Spring, .72” x 2.75” x .095” Dia. SS Comp 2-34047600, Kit, Hydro-Gear Flow Test 3-2, 3-4047662, Spark Plug, Kawasaki 4-10047663, Oil Filter, Kawasaki 4-10047878, Idler Pivot Weldment 5-24047883, Tube, Vinyl Sight Gage 3-14, 3-16048173, Washer, Wheel Damper 2-6, 2-8, 2-10048174, Block, Wheel Yoke Friction 2-6, 2-8, 2-10048183, Plate, Deck Reinforcing 5-20, 6-14048187, Handle Weldment, Deck Raise 2-34048205, Radiator, Kawasaki 2961 4-10048227, Decal, Hydro Fill Line 1-4, 1-6048272, Belt, 72" Deck Drive 6-2048284, Pump, 12cc Hydrostatic 3-6048285 2, Pump, 12cc Hydrostatic 3-6048393, Mount, Extended Drive Handle 2-24048400, Seal Kit, Hydro-Gear BDP 10-12 3-2, 3-4048451, Pulley Weldment, 9“ Idler 6-6048452, Pulley, 9” B-C Groove Idler 6-6048453, Adapter, Idler Pulley Bore 6-6048468, Rod End, 7/16-20 x 3/8 High Misalign 2-32048468, Rod End, 7/16-20 x 3/8” High Misalign 2-34048504 , Decal, Lastec, Roll Bar 1-4, 1-6048532, Key, 5mm x 5mm x 25mm 3-6048692, Strap, 1U 2-12, 2-14, 2-16, 2-32, 2-34, 2-38048712, Bushing, 1 1/16" Urethane Pivot 2-12, 2-14,

2-16, 2-34, 2-38048712, Bushing, 1-1/16" Urethane Pivot 2-32048890, Plate Assembly, Deck Adjusting 6-6048898, Blade Disc, Anti-Scalp 5-16, 5-20, 6-10, 6-14,

6-20, 6-22048908, Roller Weldment, 3373 Stripping 2-44048910, Frame Weldment, Upgrade Kit 2-44048930, Roller Lift Pivot Wldmnt 2-44048941, Strip, Roller Wiper 2-44048953, Plate, Control Box Access 2-26048988, Fitting, 3/8” NPT - 3/8” Barb 45 Deg 3-16048998, Hose, Fuel 1/4” x 48” 4-6049306, Alarm, 3372 / 3386 2-26


Part Number Index

049446, Washer, 1.50” OD x .53” ID UHMW 2-4049447, Knob w/Stud, 3/8-16 x 1.50” 2-4049448, Pull Pin, 1/2” 2-4049465, Decal, 73 Inches 1-4, 1-6049466, Decal, Comm. Deck Height Adjustment 1-4,

1-6049484, Bar Weldment, Pull 2-42049488, Bar Assembly, Pull 2-42049490, Deck Weldment, 61” Articulating #3 5-10049490, Deck Wldmnt, 61 Articulating #3 5-2049510, Bushing, Rubber Pivot 2-18, 5-8049512, Deck Weldment, 61” Center 5-8049512, Deck Wldmnt, 61 Center 5-2049526, Deck Assembly, 61” Articulating #3 5-10049532, Deck Weldment, 61 Articulatin #1 5-6049532, Deck Wldmnt, 61 Articulatin #1 5-2049537, Arm, E-Brake Link 2-36049541, Rod Assembly, Rear Deck Lift 2-38049542, Rod Wldmnt, Rear Deck Lift 2-38049544, Rod Assembly, Front Deck Lift 2-34049545, Rod Weldment, Front Deck Lift 2-32, 2-34049550, Handle Assembly, E-Brake 2-36049564, Mount Weldment, Engine 4-14049569, Arm Weldment, Hydro Tensioner 3-18049570, Idler Assembly, Hydro Drive 3-18049571, Rod, Polyurethane Spring 3-18049589, Pan Weldment, Seat 2-2049590, Seat Assembly, Complete Gas 2-2049596, Tank Weldment, 2861AGC Hyd 3-16049599, Box, Battery Modified 4-20049619, Decal, 2961AGC Articulatot Large 1-4, 1-6049620, Decal, 2973AGC Articulator Large 1-4, 1-6049668, Wheel Yoke Assembly, 13” Comm Right 2-8,

2-10, 2-20049700, Battery Assembly, 33HP 4-20049701, Boss Weldment, Rubber Spring Tensioner 4-16049702, Plate Weldment, Deck Drive Idler 4-16049705, Idler Assembly, Deck Drive 4-14, 4-16049706, Arm Assembly, Right Control Handle 2-24049707, Arm Assembly, Left Control Handle 2-24049710, Rocker Weldment, Left 2-6049717, Rocker Weldment, Right 2-6049720, Lift Weldment, Left Deck 2-16049725, Lift Weldment, Deck Tab 2-12, 2-14, 2-16049726, Lift Assembly, Left Rocker Deck 2-10, 2-16049728, Pedal Assembly, Control 2-28049730, Pedal Weldment, Foot Control 2-280497361, Frame Weldment, Comm. ROPS Lower 2-4049736-11, Frame Weldment, Comm. ROPS Lower 2-4

049738, Rod Weldment, Foot Control 2-28049739, Rod Assembly, Foot Control 2-28049740, Rocker Wheel Assembly, Left 2-8, 2-10, 2-18049741, Weldment, Left Rocker Wheel Pivot 2-18049744, Weldment, Right Rocker Wheel Pivot 2-18049745, Rocker Wheel Assembly, Right 2-8, 2-10, 2-18049747, Decal, Comm Mower Control Panel Gas 1-4,

1-6, 2-26049769, Channel, Battery Box Spacer 4-20049781, Baffle, Outside Rear Bolt-On 5-6, 5-10049784, Baffle, Outside Rear Bolt-On 5-8049787, Turnbuckle, Deck Lift Link 2-32, 2-34049788, Rod Assembly, Deck Lift Link 2-34049789, Lift Weldment, Right Deck 2-14049790, Lift Assembly, Right Rocker Deck 2-8, 2-10,

2-14049791, Cover, Left Rocker 2-6049792, Cover, Right Rocker 2-6049794, Mount Wldmnt, Deck Anti-Scalp 5-28, 6-26049795, Wheel Assembly, Deck Anti-Scalp 5-28, 6-26049796, ROPS Assembly, 2861 Folding 2-4049797, Idler Assembly, Deck Drive 5-24049809, Fitting,1/4” Barb 90 Tank w/ 3" Long Tube 4-4049809, Fitting,1/4” Barb 90 Tank w/3" Long Tube 4-2049831, Frame Weldment, ROPS 2-40498361, Pump Assembly, 12cc Left Hydro 3-6049837, Pump Assembly, 12cc Right Hydro 3-6049838, Turnbuckle Assembly, Hydro 3-6049839, Rod, Hydro Control Link 3-6049843, Link Assembly, 3/8 Suspension 2-16049843, Link Assembly, 3/8” Suspension 2-12, 2-14049847, Belt, B-134 Custom 4-10049855, Belt, B-128 Deck Drive 5-2049856, Cable Assembly, 2861 Throttle 2-26, 2-30049857, Hose, 3/8” Hyd x 12” Low Press. 3-16049857, Hose, 3/8” Hyd x 12” Low Pressure 3-4049866, Baffle Weldment, #1 Deck Mulching 5-14049868, Spacer, .53” ID x 1 1/4” OD x 1 1/4” Lng 5-8049869, Spring, Urethane 4-16049870, Bushing, Urethane Pivot 2-18, 2-40, 5-8, 5-28,

6-6, 6-26049873, Baffle Weldment, #3 Deck Mulching 5-12049877, Baffle Weldment, #2 Deck Mulching 5-14049891, Hose, 3/8” Low Pressure 28” 3-14, 3-16049892, Spindle Assembly, 2861AGC Double Sheave

5-20049893, Washer, 3 1/2” OD Wave 2-6049893, Washer, 3-1/2” OD Wave 2-8, 2-10049894, Link, Front Deck Lift 5-8, 6-6


Part Number Index

049895, Bracket, Right Seat Latch 4-20049896, Bracket, Left Seat Latch 4-20049908, Gage, Fuel Indicator 4-4049909, Grommet, Fuel gage 4-4049928, Kit, Hydro Oil Repl 5 Gal 3372 3-2, 3-4049929, Kit, Hydro Oil Repl 2 1/2 Gal 3372 3-2, 3-4049930, Decal, Belt Routing Diagram 1-4, 1-6049931, Decal, 61 Inches 1-4, 1-6049960, Baffle Weldment, #2 Deck Rear Discharge 5-12049961, Baffle Assembly, #2 Deck Rear Discharge 5-12049962, Baffle Assembly, #2 Deck Mulching 5-14049963, Baffle Assembly, #3 Deck Mulching 5-12049964, Baffle Assembly, #1 Deck Mulching 5-14049965, Wheel/Motor Assembly, 2861 Right Rear 3-8049966, Wheel/Motor Assembly, 2861 Left Rear 3-10049984, Sure Grip, Foot Pan 2-40049997, Baffle Kit, Rear Discharge 5-12049998, Baffle Kit, Mulching 61AGC 5-14050436, Relay, 40A 12VDC Automotive 4-14050477-1, Light Assy, LED Red 3/16” FI Male Quicks

2-26052025, Seat Delay Assembly, LasTec Mowers 2-2055083, Rocker Weldment, Left 2-8055084, Rocker Weldment, Right 2-8055085, Rocker Assembly, Left 2-8055086, Rocker Assembly, Right 2-8055151, Plate, E-Brake Cable Retaining 3-8, 3-10055177, Plate, E-Brake Pulley Right 3-8055178, Plate, E-brake Pulley Left 3-10055192, Bolt Weldment, Height Adjust Eye 6-6055384, Rocker Weldment, 73” Right 2-6055384, Rocker Weldment, Right 2-10055385, Rocker Weldment, 73” Left 2-6055385, Rocker Weldment, Left 2-10055386, Rocker Assembly, 73” Right 2-10055387, Rocker Assembly, 73” Left 2-10055390, Deck Assembly, 73” Articulating #1 6-4055392, Deck Assembly, 73” Articulating #3 6-8055395, Sheave, Double 73 Mower 6-22055405, Spacer, 73” Deck 1/2ID x 1-3/8 6-6055424, Baffle Weldmnt, 73” #2 Deck 6-6055427, Spindle Assembly, 73” Gas Double Sheave 6-22055428, Idler Assembly, 73” Deck Drive 6-18055429, Idler Weldment, 73” Deck Drive 6-18055438, Tank Assembly, Fuel Dual Fitting 4-4055442, Washer, 1/2” Delrin 2-38055444, Spindle Assembly, 73” Double Sheave 6-14055445, Belt, B-130 Custom 4-10055446, Tube, Fuel Pick Up 4-2, 4-4

055452, Kit, Rear Discharge Chute 5-12055464, Plate Weldment, Deck Height Adjust 2-34055481, Control Box Weldmnt, AC Gas w/ Throttle 2-26055483, Lift Weldment, Left Deck 2-12055486, Rocker Weldment, Left 2-8055803, Cover, 61A Deck #1 5-4, 5-6, 6-4055804, Cover, 61A Deck #3 5-10, 6-8055831, Lift Assembly, Left Rocker Deck 2-8, 2-12055834, Deck Assembly, 61” Articulating #1 5-4055835, Deck Weldment, 61” Articulating #1 5-4055835, Deck Weldmnt, 61 Articulating #1 5-2055841, Sure Grip, 1 1/2” Bar 2-40055843, Decal Kit, 2961AGC 1-4, 1-6055847, Decal Kit, 2973AGC 1-4, 1-6055890, Baffle Assembly, #3 Deck Mulching 73” 6-8055891, Baffle Weldment, #3 Deck Mulching 73” 6-8055895, Hose, Fuel 1/2” x 20” Long 4-10055896, Hose, Fuel 5/16” x 42” Lng 4-6055897, Tank Assembly, 29HP Hyd 3-16055924, Hose, Fuel 5/16” x 15” Lng 4-6056241, Pedal Kit, AGC Foot 2-28056244, Guard, Left Hydro Fan 4-14056250, Control Box Assembly, Gas w/Buzzer 2-26056449, Rod, Hydro Control Link 2-24056450, Turnbuckle Assembly, Hydro Diesel 2-24056547, ECU, Kawasaki 4-10056591, Decal, 18 PSI 1-4, 1-6057002, Fan, Kawasaki Cooling-29HP 4-10057501, Gauge, Kawasaki Air Filter Minder 4-18057507, Muffler, 29HP Kawasaki 49069-2356-Y 4-10059776, Capture Weldment, Clutch Stop 4-10060169, Knob, 3/8” Bore Oval/Tapered Plastic 4-8061807, Hose Clamp, Dixon Worm Gear HSS6 3-4, 3-16061953, Boot, Vinyl Cable 2-26061954, Grommet, Cable Wiper 2-26061974, Clamp, Cable 2-26062051, Washer, Water Shed Pulley 5-8, 5-24, 6-18062404, Decal, AGC/ADC Hydro 1-4, 1-6062425, Decal, Relays for 055700-055846 1-4, 1-6062429, Decal, Lastec Made in USA 1-4, 1-6062950, Adjusting Weldment, Deck 6-6062999, O-Ring, Spindle 5-22, 6-16063201, Plate, Anti-Scalp Adjusting 5-28, 6-26063206, Cable Assembly, Gas Throttle 2-26063252, Cap, Gas Fuel Tank Vented 4-4063265, Blade, 21” x 2 1/2” x 1/8” Low-Lift Ultra 5-16,

5-20063266, Blade, 25” x 2 1/2” x 1/8” Low-Lift Ultra 6-10,

6-14


Part Number Index

063377, Upgrade Kit, 61-73 AGC Roller 2-44063378, Pivot Collar Mount Weldment 61-73AGC 2-44063382, Plate, Clamp Pivot Collar Mount 2-44063383, Arm, Roller Lift Link 61-73 AGC 2-44063384, Spacer, Lift Link Arm 61-73 AGC 2-44063869, Plate, Roller Mount 2-44063870, Tube, Roller Mount Spacer 2-44064468, Hood Assembly, 29HP Kawasaki CE 1-9064500, Nut Assembly, 3/8-16 Cover Retaining 1-9064521, Kit, 2961/73 CE Hardware 1-9064653, Vent, Remote w/Valve 4-2064654, Grommet, Remote Vent 4-2064658, Fitting, 1/4” Tee Barb 4-6067065, Decal Kit, CE Deck 1-6067359, Tank Assembly, Gasoline Dual Fittings 4-2067363, Cap, Gas Fuel Tank Ratchet 350 4-2067364, Tube, 3.5" Vapor Neck 4-2067370, Carbon Canister, 9 Gal 4-6067381, Battery, Group 26 w/Handle 4-20067686, Spacer, Spindle Bearing Housing 5-18, 6-12067687, Shaft, Blade Spindle ZT Cast 5-18, 6-12067688, Sheave, Double - Mower Deck 5-16, 6-10067694, Spindle Assembly, ZT 25” D6.3-6.3 6-4, 6-8,

6-10067695, Spindle Assembly, ZT 21” D6.3-6.3 5-4, 5-8,

5-10, 5-16067696, Spindle Assembly, Center w/Stiffener 5-18,

6-12067696, Spindle Assembly, ZT Cast 5-16, 6-10, 6-20067973, Hose Clamp, 3/16” Spring 4-6067999, Spindle Housing, ZT- Common Core 5-18, 6-12071864, Fitting, 8 ORFS - 10 STOR 90 3-8, 3-10072486, Spindle Assembly, 73” Gas Double Sheave 6-20072486, Spindle Assy, 73” Gas Double Sheave 6-6072497, Spacer, 1 OD x .65 ID x .53 Long 5-8072497, Spacer, 1 OD x .65 ID x .53 Long 6-6072505, Hose Clamp, 3/16” Spring 3-14072506, Hose Clamp, 1/4” Spring 4-6072507, Hose Clamp, 5/16” Spring 4-6072511, Spacer, Bearing Housing 5-18, 6-12072539, Fitting, 6 ORFS - 6 PushLok 90 3-14072541, Fitting, 6 ORFS - 6 PushLok ST 3-14072556, Fitting, 6 ORFS - 6 MPT 90 3-14072560, Fitting, 8 ORFS - 8 STOR LL 90 3-6072582, Tank Weldment, 28AGC Hyd 3-14072584, Fitting, 6 ORFS - 6 MPT 45 3-14072585, Fitting, 6 ORFS - 6 STOR 90 3-6072587, Hose Assembly, 1/2” HP x 30” ORFS 8 ST 3-20725871, Hose Assembly, 1/2HP x 30In ORFS 8 ST 3-6

072588, Hose Clamp, 1/2” Spring 4-6, 4-10072589, Screen, Radiator Kawasaki 29Hp 4-10072591, Tank Assembly, 29AGC Hyd 3-14072594, Hose, 3/8” Hyd x 4” Low Press. 3-14072595, Hose, 3/8” Hyd x 10” Low Press. 3-14072596, Hose, 3/8” Hyd x 14” Low Press. 3-14072597, Hose Assembly, 3/8” LP x 6” ORFS 6 90 3-2,

3-14072598, Hose Assembly, 3/8” LP x 12” ORFS 6 ST 3-14072598, Hose Assembly, 3/8” LPx12” ORFS 6 ST 3-2072599, Hose Assembly, 3/8” LP x 16.5” ORFS 6 45 3-2072599, Hose Assembly, 3/8” LPx16.5” ORFS 6 45 3-14072600, Fitting, 6 ORFS - 6 PushLok 45 3-14072684, Clutch Assembly, 5.75 Pitch 1 1/8 Bore 12V

4-10072735, Gauge, Fuel Indicator Sealed 4-2072736, Grommet, Fuel Gauge Sealed 4-2072858, Tank Assembly, 7 Gallon Gas Dual Fitting 4-2073357, Housing Cap Dirt Ejector, Kohler Filter 4-18073389, Sheave, Double - D7.0-6.3 6-20085614, Grommet, Rubber 2 1/2” Dia 4-2, 4-4EE20482, Light, Red 12 Volt .187 Tabs 2-26FF04203-6, Rivet, 3/16” Dia x 3/8-1/2” Grip Range Pop

1-9F04254-12, Ring, 62mm IR Din #472 Retaining 4-14,

4-16, 5-8, 5-24, 6-18F04254-4, Ring, 1.575” ID 3000-156 Retaining 6-6F04254-45, O-Ring, 2 7/16" ID x 3/16" Diameter 5-22F04254-45, O-Ring, 2-7/16"ID x 3/16" Diameter 6-16F04254-46, Ring, 3/4” External - External 2-28, 5-8, 6-6F04254-46, Ring, 3/4” External Retaining 2-44F05004-1, Screw, 10-24 x 1/2” Sl Hex Machine 2-40F05004-123, Bolt, 3/8-16 x 3 1/2” Hex Head Gr5 2-32F05004-123, Bolt, 3/8-16 x 3 1/2” Hex Head Grade 5

2-34F05004-126, Screw, 10-24 x 3/4” Phillips PH Machine

2-40F05004-18, Screw, 10-24 x 5/8” Unsl Indent HH Ma-

chine 4-2, 4-4, 4-14F05004-19, Screw, 10-24 x 1 1/4” Unsl Ind HH Machine

4-6F05004-237, Screw, M8 x 1.25 x 60 Hex Washer Hd w/o

Serr 4-18F05004-238, Screw, M8 x 1.25 x 14 Hex Washer Hd w/o

Serr 4-18F05004-285, Screw, 10-24 x 5/8” SBHC SS 4-2F05004-35, Screw, 10-24 x 1/2” SBHC 4-8, 4-12


Part Number Index

F05004-48, Bolt, M10-1.5 x 25mm Hex Head FT 8.84-10

F05004-93, Screw, 6-32 x 3/4” SBHC SS 2-26F05005-101, Bolt, 1/4-20 x 1” Hex Head Grade 5 3-6,

4-12F05005-105, Screw, 1/4-28 x 1/4” BO SH Cup Pt Set

2-24F05005-105, Screw, 1/4-28 x 1/4” BO Socket Head Pt

Set 2-12, 2-14, 2-16F05005-116, Bolt, 1/4-20 x 1 1/4” Hex Head Grade 5

4-20F05005-123, Bolt, 1/4-20 x 3/4” Hex Head Grade 5 4-12F05005-137, Bolt, 1/4-20 x 5/8” Hex Head Grade 5 2-26F05005-68, Bolt, 1/4-20 x 1 3/4” Hex Head Grade 5 4-6F05005-79, Bolt, 1/4-20 x 1/2” Hex Head Cap 2-6F05005-79, Bolt, 1/4-20 x 1/2” HHC 3-14, 3-16F05006-101, Bolt, 5/16-18 x 3/4” Hex Head

W/Flat&Lock Washer 4-14F05006-102, Bolt, 5/16-18 x 3/4” Hex Head Grade 5 2-2,

2-40, 4-6F05006-102, Bolt, 5/16-18 x 3/4” Hex Head Grade 5 Zinc

2-26, 3-8, 3-10, 4-20, 5-8F05006-110, Bolt, 5/16-18x9 HH Gr5 Spcl 5-26, 6-24F05006-117, Bolt, 5/16-18 x 3/4” SHC SS 3-8, 3-10F05006-123, Bolt, 5/16-18 x 8-1/2” Hex Head Grade 5

4-20F05006-140, Bolt, 5/16-18 x 5” Hex Head Grade 5 5-22,

6-16F05006-27, Bolt, 5/16-18 x “1 Hex Head Grade 5 4-10F05006-27, Bolt, 5/16-18 x 1” Hex Head Grade 5 2-2,

2-26, 2-44, 4-20, 5-6, 5-8, 5-10

F05006-81, Bolt, 5/16-18 x 1 3/4” FT Hex Head Gr5 2-32F05006-93, Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread

Gr5 5-22F05006-93, Bolt, 5/16-18 x 1 1/4” Hex Head Full Thread

Grade 5 5-10F05006-93, Bolt, 5/16-18x1 1/4 HH FT Gr5 6-16F05007-109, Bolt, 3/8-16 x 4 3/4” Hex H ead Grade 5

2-38F05007-118, Bolt, 3/8-16 x 3/4” Hex Head Grade 5 2-44F05007-119, Bolt, 3/8-16 x 1 3/4” Hex Head Grade 5

2-32, 2-34F05007-123, Bolt, 3/8-16 x 1 1/4” Hex Head Grade 5

2-24, 3-8, 3-10, 4-10F05007-123, Bolt, 3/8-16x1 1/4 HH Gr5 5-28, 6-26F05007-124, Bolt, 3/8-16 x 2” Hex Head Grade 5 3-10F05007-125, Bolt, 3/8-16 x 2 1/2” Hex Head Grade 5

2-12, 2-14, 2-16, 2-40

F05007-126, Bolt, 3/8-16 x 4” Hex Head Grade 5 2-4, 2-12, 2-14, 2-16, 2-32, 2-34

F05007-127, Bolt, 3/8-16 x 1 1/4” Carriage Grade 5 2-30F05007-127, Bolt, 3/8-16 x 1 1/4” Carriage Grade 5 2-26F05007-129, Bolt, 3/8-16 x 1 3/4” FT Grade 5 4-8F05007-136, Bolt, 3/8-16 x 3 3/4” Hex Head Grade 5

2-32, 2-34, 2-38, 4-14F05007-165, Bolt, 3/8-16 x 1” Carriage Grade 5 5-12,

5-14, 6-8F05007-165, Bolt, 3/8-16 x 1” Carriage, Zinc Grade 5

5-8, 6-6F05007-206, Bolt, 3/8-16 x 2 3/4” Hex Head Grade 5 2-4F05007-214, Screw, 3/8-16 x 2” SHC 4-8F05007-244, Bolt, 3/8-16 x 4 1/2” Hex Head 316 SS 2-2F05007-58, Screw, 3/8-16 x 2” BO SHC 4-8F05007-73, Bolt, 3/8-16 x 3” Hex Head Gr5 2-32F05007-73, Bolt, 3/8-16 x 3” Hex Head Grade 5 2-34F05007-78 , Bolt, 3/8-16x1 1/2 HH Gr5 2-46F05007-78, Bolt, 3/8-16 x 1 1/2” Hex Head Grade 5 2-36,

2-38, 3-6, 5-16, 5-24, 6-6, 6-10, 6-18, 6-20

F05007-85, Bolt, 3/8-16 x 1 1/2” Carriage Gr5 6-14, 6-22

F05007-85, Bolt, 3/8-16 x 1 1/2” Carriage Grade 5 5-12, 5-20, 6-8

F05007-87, Bolt, 3/8-16 x 1” Hex Head Grade 5 3-14, 3-16

F05007-87, Bolt, 3/8-16 x 1” Hex Head Grade 5 2-24F05008-10, Bolt, 1/2-13 x 2 1/4” Hex Head Grade 5 3-18,

4-14, 4-16, 5-24F05008-106, Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade

5 2-6F05008-106, Bolt, 1/2-13 x 4 3/4” Hex Head Cap Grade

5 2-8, 2-10F05008-143, Bolt, 1/2-13 x 3 3/4” Hex Head Grade 5

2-44F05008-159, Bolt, 1/2-13 x 6 1/2” Hex Head Grade 5

2-44F05008-23, Bolt, 1/2-13 x 3” Hex Head Grade 5 2-4, 2-8,

2-10, 5-8F05008-23, Bolt, 1/2-13 x 3” Hex Head Grade 5 Zinc 2-6F05008-28, Bolt, 1/2-13 x 5 1/2” Hex Head Grade 5 3-8,

3-10F05008-35, Bolt, 1/2-13 x 4 1/2” Hex Head Cap Grade 5

2-8, 2-10F05008-35, Bolt, 1/2-13 x 4-1/2” Hex Head Gr5 2-6F05008-37 , Bolt, 1/2-13x1 1/4 HH Gr5 2-46F05008-37, Bolt, 1/2-13 x 1 1/4” Hex Head Grade 5 2-12,

2-14, 2-16, 2-44


Part Number Index

F05008-61, Bolt, 1/2-13 x 3 1/2” Hex Head Grade 5 6-6F05008-96, Bolt, 5/16-18 x 1 1/2” Hex Head Grade 5

2-24F05009-10, Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 2-6F05009-10, Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 2-8,

2-10, 5-8F05009-10, Bolt, 5/8-11 x 4 1/2” Hex Head Grade 5 6-6F05009-108, Bolt, 3/4-10 x 9” Hex Head Grade 5 2-20F05009-111, Bolt, 5/8” x 1/2” Shoulder 2-44F05009-20, Bolt, 5/8-11 x 2 1/2” Hex Head Grade 5 5-4,

5-6, 5-10, 6-4, 6-8F05009-28, Bolt, 5/8-11x4 Gr5 HH 5-28, 6-26F05009-35, Bolt, 5/8-11 x 2 3/4” Hex Head Grade 5 2-42,

6-4, 6-8F05009-35, Bolt, 5/8-11x2 3/4 HH Gr5 5-28, 6-26F05009-37, Bolt, 5/8-11 x 3 Hex Head Grade 5 2-8, 2-10F05009-37, Bolt, 5/8-11 x 3” Hex Head Grade 5 2-44F05009-37, Bolt, 5/8-11 X 3” Hex Head Grade 5 Zinc 2-6F05009-66, Bolt, 1/2-13 x 2 3/4” Hex Head Grade 8 6-18F05009-70, Bolt, 5/16-18 x 1 3/4” Hex Head 3-6F05009-95, Bolt, 5/8-18 x 1 3/4” Hex Head Grade 5 5-16,

5-20, 6-10, 6-14, 6-20, 6-22F05010-1, Nut, 3/8-16 Hex 2-24, 5-24, 6-6, 6-18F05010-10, Nut, 3/8-16 Hex Nyl Lock 2-30F05010-10, Nut, 3/8-16 Hex Nyl Lock 2-12, 2-14, 2-16F05010-10, Nut, 3/8-16 Hex Nyloc 2-4, 2-12, 2-14,

2-16, 2-26, 2-32, 2-34, 2-36, 2-38, 2-40, 3-6, 4-8, 4-14, 5-6, 5-10, 5-20, 5-28, 6-14, 6-26

F05010-10, Nut, 3/8-16 Hex Nylon Lock 6-6, 6-22F05010-119, Nut, 5/16-24 Jam LH 2-24, 3-6F05010-121, Nut, 5/16-18 Nylon Locking Jam 3-8, 3-10F05010-123, Nut, 3/8-24 Free 2-24, 2-28, 3-6F05010-124, Nut, 3/8-16 Half Nyloc 2-24, 2-32, 2-34,

3-8, 3-10, 4-10F05010-124, Nut, 3/8-16 Half Nylock 3-14, 3-16F05010-14, Nut, #10-24 Keps 2-40, 4-14F05010-160, Nut, 10-24 Hex Nylock 4-2, 4-6, 4-8, 4-12F05010-166, Nut, 3/8-24 LH Jam 2-32, 2-34, 2-38F05010-17, Nut, 5/16-18 Hex 2-26, 2-32F05010-177, Nut, 3/4-10 Stover Swaged 2-20F05010-185, Nut, 5/8-11 FlexLoc 2-8, 2-10, 5-4, 5-6,

5-10, 5-28, 6-4, 6-8, 6-26F05010-185, Nut, 5/8-11 Flexloc 2-6F05010-185, Nut, 5/8-11 Flexlock 2-44F05010-201, Nut, 1/2-13 Hi-Crown Acorn Cap Plated

2-8, 2-10F05010-22, Nut, 3/8-24 UNF Hex Jam 2-38

F05010-220, Nut, 1/4-20 Flanged Hex Nylock 4-6F05010-221, Nut, 5/16-18 Flanged Hex Nylock 4-6F05010-222, Nut, 3/8-16 Flanged Hex Nyl Lock 5-12F05010-222, Nut, 3/8-16 Flanged Hex Nyloc 5-4, 5-16,

5-24, 6-10F05010-222, Nut, 3/8-16 Flanged Hex Nylock 5-14, 6-4,

6-6, 6-8, 6-18F05010-222, Nut, 3/8-16 Flanged Hex Nylon Lock 5-8,

6-20F05010-223, Nut, 1/2-13 Flanged Hex Nylock 6-6, 6-18F05010-223, Nut, 1/2-13 Flanged Nylon Hex Lock 5-24F05010-224, Nut, 5/8-11 Flanged Hex Nylock 5-8F05010-224, Nut, 5/8-11 Flanged Hex Nylock 6-6F05010-234, Nut, 3/8-16 Hex Half Nylon Lock 316 SS

2-2F05010-29, Nut, 3/8-16 Jam 6-6F05010-34, Nut, 5/8-11 Nyl Lock 2-18F05010-35, Nut, 1/2-13 Hex 4-16F05010-38, Nut, 7/16-20 Jam 2-32, 2-34F05010-58, Nut, 5/16-18 Nylok Hex 2-2, 2-24, 3-6,

4-10, 5-6, 5-10, 5-26, 6-16, 6-24

F05010-58, Nut, 5/16-18 Nylon Lock Hex 2-40, 5-8, 5-22

F05010-59, Nut, #6-32 Keps 2-26F05010-69, Nut, 1/4-20 Nylock 4-20F05010-69, Nut, 1/4-20 Nylon Lock 4-12F05010-8, Nut, 1/2-13 Hex Nylon Lock 2-44F05010-8, Nut, 1/2-13 Nyl Hex Lock 2-6F05010-8, Nut, 1/2-13 Nyl Hex Lock 2-6F05010-8, Nut, 1/2-13 Nyl Hex Lock 2-8, 2-10, 2-36,

3-8, 3-10, 4-14F05010-8, Nut, 1/2-13 Nylon Hex Lock 2-4, 2-8, 3-18,

4-16, 5-8F05010-82, Nut, 5/8-11 Jam 5-28, 6-26F05010-9, Nut, 1/4-20 Keps 4-12F05010-96, Nut, 5/8-11 Jam Nyl Lock 5-28, 6-26F05011-101, Washer, 1/2” SAE Flat Gr5-8 (Thru Hard)

2-38F05011-101, Washer, 1/2” SAE Flat Grade 5-8 (Thru

Hard) 3-8, 3-10F05011-104, Washer, 3/8 x 1-1/2 x 1/8 Thick Hardened

5-24F05011-104, Washer, 3/8” x 1 1/2” x 1/8” Thk Hardened

6-18F05011-104, Washer, 3/8” x 1-1/2” x 1/8” Thk Hardened

6-6F05011-107, Washer, .625 ID x 1.312 OD x .050 Thick

Nylon 2-44


Part Number Index

F05011-11, Washer, 1/4” SAE Flat 2-6F05011-11, Washer, 1/4” SAE Flat 4-20F05011-110, Washer, 3/8” Push Nut 2-28F05011-111, Washer, 20mm Bellville 2-28F05011-115, Washer, 1” ID .03 SS Shim 3-8, 3-10F05011-116, Washer, 1” ID .06 SS Shim 3-8, 3-10F05011-117, Washer, 7/16” Nord-Lock 4-10F05011-13, Washer, 5/16 Split Lock 4-6, 4-20, 6-16F05011-13, Washer, 5/16” Split Lock 2-26, 2-44, 3-8,

3-10, 4-20, 5-8, 5-22F05011-14, Washer, 1/4” Split Lock 2-6, 3-14, 3-16F05011-14, Washer, 1/4” Split Lock 2-26, 3-6F05011-16, Washer, 5/16” Standard Flat 3-8, 3-10F05011-17, Washer, 5/16 SAE Flat 4-10F05011-17, Washer, 5/16” SAE Flat 5-8, 5-10F05011-17, Washer, 5/16” SAE Flat 2-26, 2-40, 2-44,

4-20, 5-6F05011-18, Washer, #10 SAE Flat 4-6, 4-14F05011-2, Washer, 1/2” SAE Flat 2-12, 2-14, 2-16,

2-36, 3-18, 4-16F05011-20, Washer, #10 Split Lock 2-26, 2-40, 4-2, 4-4F05011-27, Washer, 5/8” Split Lock 5-20, 6-14F05011-3, Washer, 3/8” Flat SAE 3-14, 3-16F05011-3, Washer, 3/8” Flat SAE 2-4, 2-12, 2-14, 2-16,

2-24, 2-26, 2-28, 2-32, 2-34, 2-38, 3-6, 3-8, 3-10, 4-10, 4-12, 4-14, 5-6

F05011-3, Washer, 3/8” SAE Flat 2-30F05011-3, Washer, 3/8” SAE Flat 2-44F05011-33, Washer, 5/16 Star ET 4-10F05011-4 , Washer, 3/8 Split Lock 2-46F05011-4, Washer, 3/8” Split Lock 2-24, 2-44, 4-10,

6-18F05011-40, Washer, 5/8” Standard Flat 2-42F05011-5, Washer, 5/8” SAE Flat 2-6F05011-5, Washer, 5/8” SAE Flat 2-8, 2-10, 2-18, 4-16F05011-50, Washer, 5/16” x 1 1/4” Fender 2-2F05011-62, Washer, 3/4” SAE Flat 2-20F05011-68, Washer, 1/2” Standard Flat Zn 4-14, 4-16F05011-77, Washer, 3/4” AN Yel/Cad 2-28, 2-44, 5-8,

6-6F05011-88, Washer, 10mm Split Lock 4-10F05011-89, Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat

5-20F05011-89, Washer, 2 1/2” OD x 5/8” ID x 3/16” Std Flat

Znc 5-16, 6-10, 6-20, 6-22F05011-89, Washer,2 1/2” OD x 5/8” ID x 3/16” Std Flat

Znc 6-14F05011-9 , Washer, 1/2 Split Lock 2-46

F05011-9, Washer, 1/2” Split Lock 2-44, 5-8F05011-97, Washer, 1/2” Plain Belleville 2-36, 5-16,

5-20, 6-10, 6-14, 6-20, 6-22F05012-1, Pin, 1/8” x 1” Cotter 2-36F05012-11, Pin, 3/16” x 1” Roll 2-36F05012-115, Pin, 3/4” Clevis Retaining 2-36, 4-16F05012-21, Pin, 3/16” x 1” Cotter 4-16F05012-3, Pin, 1/8” x 3/4” Cotter 2-28F05012-49, Pin, 1/8” x 1 1/2” Cotter 2-20, 3-8, 3-10F05012-64, Pin, 1/8” x 1/2” Roll 5-22F05012-64, Pin, 1/8x1/2 Roll 6-16F05012-79, Pin, 5/32” x 1 1/2” Cotter 2-20F05012-8, Pin, 3/8” x 1 3/32” Clevis 2-38F05015-17, Bolt, #10-24 x 1/2” PH 2-30F05015-17, Bolt, #10-24 x 1/2” Phillips PH 2-26F0510-185, Nut, 5/8-11 FlexLoc 2-42F412, Screw, Seat Switch 2-2F81003-29, Bolt, M10-1.5 x 55mm Hex Head Full

Thread G5 4-10IIS-0192 , Instr. Sheet, 61 Deck Striping Kit 2-46IS-0218, Instruction Sheet, 056241 Kit 2-28IS-0277, Instruction Sheet, 61-73 Roller Assembly 2-44IS-0307, Instruction Sheet, 2961/73 CE Hardware Kit

1-9NN/A, Bolt, 3/8-16 x 7” Hex Head Grade 5 2-12, 2-14,

2-16N/A, Bushing, 3/8” Polyurethane Suspension 2-12, 2-14,

2-16N/A, Spacer, 3/8” Suspension 2-12, 2-14, 2-16N/A, Washer, 3/8” Suspension 2-12, 2-14, 2-16PP04107, Fitting, 3/16” x 3/16” Straight Grease 5-20P04211, Knob, 5/8-18 Ball 2-32, 2-34, 2-36, 2-44P04332, Cap, 3/8” Pipe Galvanize 4-10P04332, Cap, 3/8” Pipe Galvanized 3-14, 3-16P04646, Nut, 1/2-20 Lug 3-8, 3-10P05035, Collar, 5/8” ID Lock 2-24P06030-2, Bearing, 6203-2NSL 17mm SRI-2 ABEC-1

6-6P06104, Foot, Rubber 4-8, 4-12P07584, Clamp, 1/2” EMT Coated 4-14P09895, Clamp, 2 1/2” Worm 4-18P103, Bearing, Spindle Top 6305 RS 4-14, 4-16, 5-8,

5-24, 6-18P105, O-Ring, 2 1/2” ID x 2 3/4” OD 5-18, 6-12P107, Blade, 25” x 2-1/2” x 1/4” High Lift 6-20P107, Fitting, 1/4-28 Straight Grease 2-6


Part Number Index

P107, Fitting, 1/4-28 Straight Grease 2-8, 2-10, 2-28, 2-40, 2-44, 5-16, 6-10, 6-14, 6-20, 6-22

P110, Pin, 3/8” x 1 5/16” Clevis 2-28, 2-36, 2-38P110, Pin, 3/8” x 1 5/16” Clevis, Yzn 5-8, 6-6P11035, Bearing, 6206-2NSE 5-18, 5-22, 6-12, 6-16P111, Ring, 1” Kick-Out 2-34, 2-38P111, Ring, 1” Kick-out 4-12P111, Ring, Kick-out, 1” 2-32, 5-8, 6-6P11258, Strap, 24” Rubber w/Hooks 4-20P117, Decal, Hands & Feet 1-6P12161, Washer, Felt Battery Terminal 4-20P12708, Fitting, 3/8” NPT-3/8” Barb Elbow 3-14, 3-16P12724, Fitting, 3/8” NPT-3/8” Barb 3-14, 3-16P12724, Fitting, 3/8” NPT-3/8” Barb 4-10P12739, Hose Clamp, 11/16” Worm 3-16P128, Blade, 21” x 2 1/2” x 1/4” High Lift 5-16, 5-20P190, Bearing, 1” ID Tapered Roller 2-20P191, Seal, 1 1/4” ID Trb Bearing 2-8, 2-10P195, Cap, Hub 2-8, 2-10, 2-40P212, Pin, 3/8” x 2 1/8” Clevis 2-34P212, Pin, 3/8” x 2 1/8” Clevis, Yzn 2-32, 5-8, 6-6P246, Blade, 21” Low-Lift 5-16, 5-20P292, Bearing, Tapered Roller, 3/4” ID 2-22P293, Seal, TRB, 3/4” ID 2-22P294, Fitting, 1/4-28 45 Deg Grease 4-14, 5-24, 6-18P296, Spacer, 1.13” OD x .75” ID x .5” 2-20P322, Blade, 21” Gator Mulching 5-14, 5-16, 5-20P402, Bearing Race Insert, 3/4" TRB 2-22

P434, Nut, 3/4-16 Castle 2-20P478 , Decal, Danger - Rotating Blades 1-4, 1-6P485, Decal, Fuel Equipment 4-4P485, Decal, Fuel Equipment 325E 1-4, 1-6P611, Holder, Jumbo Cup Black 2-40P619, Filter Head, 3/8” NPT 3-14, 3-16P620, Filter Element, Spin On, BE-25-25 Zinga 3-2, 3-4,

3-14, 3-16P629, Grip, Foot Control Black 2-28P630, Seat, Air Ride (Color Gray) 2-2P649, Hose Clamp, 7/32”-5/8” 3-16P686, Yoke, 3/8In-24 2-28P701, Blade, 25” x 2 1/2” x 1/4” High Lift 6-10, 6-14P776, Seat Belt, 2” ALR/ERI Buckle 2-2P786, Bushing, 3/4” ID x 1” OD x 5/8” Lng Flanged

2-36, 4-16P826, Switch, Seat 2-2P829, Bushing, 1/2” ID x 3/4” OD x 1/2” Brnz 2-12,

2-14, 2-16P848, Blade, 25" Gator Mulching 6-10, 6-14P849, Blade, 25” x 2 1/2” x 1/4” Low Lift 6-10, 6-14P849, Blade, 25” x 2-1/2” x 1/4” Low Lift 6-22SS08291-W, Handle, Power/Feed & Up/Down 4-8S12284, Tube, 7/8” Dia Elec Motor Spacer 2-32S12284, Tube, 7/8” Dia. Elec Motor Spacer 2-34S21486, Key, 1/4” SQ x 3-3/8” Long 4-10


Documents

The Articulator 2961AGC/2973AGC Parts Manual