TH250 Quick Reference

Warranty Information

Wincor Nixdorf guarantees a limited warranty engagement for 12 months beginning with the date of delivery. This warranty engagement covers all those damages which occur despite a normal use of the product. Damages because of - improper or insufficient maintenance, - improper use of the product or unauthorized modifications of the product, - inadequate location or surroundings will not be covered by the warranty.

Manufacturers Certification

This device complies with the requirements of the directive 2004/108/EC with regard to “Electromagnetic Compatibility” and 2006/95/EC "Low Voltage Directive" and RoHS directive 2011/65/EU. Therefore, you will find the CE mark on the device or packaging.

Underwriters Laboratories

In addition, the device has received the UL and cUL approval.

Federal Communications Commission (FCC) Radio Frequency Interference Statement Warning

Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Information to the User This equipment must be installed and used in strict accordance with the manufacturer’s instructions. However, there is no guarantee that interference to radio communications will not occur in a particular commercial installation. If this equipment does cause interference, which can be determined by turning the equipment off and on, the user is encouraged to contact Wincor Nixdorf immediately. Wincor Nixdorf is not responsible for any radio or television interference caused by unauthorized

modification of this equipment or the substitution or attachment of connecting cables and equipment other than those specified by Wincor Nixdorf. The correction of interferences caused by such unauthorized modification, substitution or attachment will be the responsibility of the user. This class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de la classe A est conforme à la norme NMB-003 du Canada. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation.

Unpack the Printer

Unpack the printer, saving all packing materials for future shipping or storage.

Changing the paper roll

1

4

Connecting the cables

Depending on your printer configuration, the connector panel may vary from the illustration.

Connector Interface panel

optional

e.g. RS-232C

CommunicationConnector

USBConnector

Power SupplyConnector

CashDrawer

Connector

Run a diagnostic test print

Open cover

Push and hold Paper Feed Button while closing cover

Configure the printer if necessary

The TH250 is an ENERGY STAR® qualified printer. To set or to adjust the energy-savings timeout value:

Select “Set Firmware Features” from the main menu. Scroll to “Set Enter ENERGY STAR Timeout Value?” Select “Yes”. Printer responds with the following timeout value selections:

- Disable (no timeout) -> 1 click

- 15 minute timeout -> 2 clicks

- 30 minute timeout -> 3 clicks

- 60 minute timeout -> 4 clicks

Enter clicks for selection, then hold button down at least 1 second to validate.

Power cycle the printer.

To revive a printer that has entered the energy-savings mode, press the paper feed button.

Current printer tallies are printed after the diagnistic information and will vary per printer use.

Safety instructions

Do not touch the printer’s cutter and tear bar.

The print head is a thermal element and it is at high temperature during printing or just after operation. Therefore, do not touch it and its peripherals for safety reasons.

The thermal head is an ESD-sensitive device. To prevent damage, do not touch either its printing part or connecting parts.

Caution: Install the printer on a flat and stable place.

Reserve adequate space around the printer so that convenient operation and main-tenance can be performed.

Keep the printer away from water source.

Do not use or store the printer in a place exposed to heat or fire, moisture, serious pollution and direct sunlight.

Do not place the printer on a place exposed to vibration or impact.

No dew condensation is allowed to the printer. In case of such condensation, do not turn on the power until condensation completely disappeared.

Only use power supply units and cables released by Wincor Nixdorf.

Connect the printer to “UL Listed Computers” only.

Only connect cables to the 24V connector which are marked with DP-1 or DP-2.

The printer should only be disassembled or repaired by a technician who is certified by the manufacturer.

Further Information

Please find detailed information about the printer in the Operator’s Guide. That document as PDF file and needed drivers can be downloaded from this web site: http://www.wincor-nixdorf.com

http://www.wincor-nixdorf.com/internet/site_EN/EN/Support/Downloads/POSLotterySystems/poslotterysystems_node.html

Consumables Please order consumables at: http://www.wincor-nixdorf.com/mediaservice Copyright© Wincor Nixdorf Pte Ltd, 2015 The reproduction, transmission or use of this document or its contents is not permitted without express authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved.

Delivery subject to availability; technical modifications possible.

Order No. 01750275431 C