Testors Product Guide

Enamels Lacquers

A c ry l ics Fin ishes

Cements Accessories

P r o d u c t

G u i d e

Testor Enamels

Model Master Enamels

B oy d s Custom Car Enamels

Model Master Metalizers

Pa c t ra RC Finishes

Model Master A c ryl (New )

Model Master A c rylics (Original)

Pa c t ra A c rylics

Clear Lacquer Finishes

Clear Enamel Finishes

Clear Finish for A c rylics

Plastic Hobby Cements

Wood/Clear Hobby Cements

Instant Hobby Cements

Enamel Thinners

Decal Solutions

Pa rafilm/Masking Material

Pa c t ra Masking/Trim Ta p e s

T e s t o r P r o d u c t G u i d e

E n a m e l s

L a c q u e r s

A c ry l i c s

F i n i s h e s

C e m e n t s

A c c e s s o r i e s

S i z e s # Colors

1/4 oz. b o t t l e s 4 5

1 oz. b o t t l e s 1

3 oz. s p ray 4 1

Pe n s 1 4

Description:

Testor all-purpose (Lead Free) enamelsa re fast-dry i n g , easy to apply and can beused on many kinds of surfaces. F i n e l yg round pigments produce a superb flowand maximum cov e ra g e . All colors arep roduced i n - h o u s e allowing us to monitoreach batch as to color- m a t c h ,o p a c i t y,v i s c o s i t y, e t c .

Testor enamels can be used on manysurfaces including polystyrene plastic, A B Splastic,styrofoam,glass,plexiglass, wood,m e t a l ,l e a t h e r. Our enamels will not adhereto polye t hylene or polypro py l e n e . It is alsonot recommended for rubber, or flexible typesof viny l , because it will not dry on thesesurfaces; it will remain tacky to the touch.

U s a ge / Ti p s :

Always follow instructions and safetyp ro c e d u res, printed on packaging!

1 ) Best conditions: 7080 degrees F,m o d e rate relative humidity.

2 ) D ry time: depends on thickness andc o n d i t i o n s , shown are appro x i m a t e s :

F l a t s 30 min. to 1 hour

G l o s s 1 hour to touch, full cure is4872 hours.

N O T E : Paint cures from the outside in!

3 ) When brushing, use long strokes inone dire c t i o n , to minimize brush marks.

4 ) Thinning of gloss enamels: start at3 parts paint to 2 parts thinner.

Thinning of flat enamels: start at 3parts paint to 1 part thinner.

Thin to the consistency of whole milk.

5 ) When airbrushing or aerosol spray i n g ,apply paint in sev e ral mist applicationsf i r s t , letting tack between coats; this buildsup a base for the final heavy coat, w h i c hwill minimize sags and runs.

6 ) If masking with PA R A F I L M, re m ov eafter 1 hour when airbrushing, 48 hourswhen using aerosol spray.

7 ) When clear-coating over metallics, i . e . ,c h ro m e ,s i l v e r, c o p p e r, a l u m i n u m , d onot use Clear Top Coat Enamel!

T e s t o r E n a m e l sEnamels

The enamel will deleaf or dull themetallics. Instead use Glosscote o rDullcote Lacquer! You can also useclear acry l i c s , or Future floor wa x ,a sthese will not diminish the re f l e c t a n c eof the metallics.

8 ) Apply acrylics after the enamel hasc u red at least 24 hours.

9 ) To achieve a matte or semiglossf i n i s h , mix 50% gloss and 50%flat together.

10 ) To achieve a tra n s p a rent finish, m i x50% enamel with 50% gloss orflat clear.

11 ) When decaling, a l ways use a cleargloss coating over flat enamels toa c h i eve proper decal adhesion andp revent silvering.

1 2 ) Do not use Pa c t ra Formula U FuelP roofer over enamel finishes.

1 3 ) To bring out the fluorescent colors, abase coat of white needs to be appliedto the substra t e .F l u o rescent colors arenot phosphorescent,and will fade ifexposed to UV ray s .

14 ) To create a finer mist in aerosol cans,place the can in a shallow pan ofwarm water for approximately 2m i n u t e s .B e f o re application, s h a k ecan vigorously and thoro u g h l y.

15 ) If a flat enamel is not as flat as desire d ,pour out only the amount re q u i red atone time,into a separate container.

Add a little bit of talc powder andflatten to your liking. Remaining mixedenamel should be disposed of pro p e r l y.

16 ) When using tra n s p a rent or semi-t ra n sp a rent colors, the substra t e s colorwill affect the finishs color and hue,if the substrate color is not neutra l i z e d .This can be achieved by priming in ac o m p l e m e n t a ry color.

E x a m p l e :Yellow Pearl over a driedprimer coat of opaque ye l l o w.

1 7 ) To prevent gelling or eva p o ration inthe bottle during long-term stora g e ,clean off rim of bottle and inside ofc a p, tightly close cap and invert bottleto wet the cap liner; when this dries, i twill form a seal that reduces oxygendiffusion into the bottle.

1 8 ) Testor enamels have a shelf life of35 years if stored pro p e r l y.

1 9 ) Testor enamels (except for the leafingmetallics) may be re m oved with ord i n a ryoven cleaners. Leafing metallics shouldbe re m oved in layers with enamel thinner.

2 0 ) To re m ove clear lacquers, use rubbingalcohol.The alcohol will not removeenamels or attack decals.

1700 & 1900 series( F S / M i l i t a ry )

2000 & 2100 series( F S / F i g u re s )

2700 & 2900 series( C a r s )

1700 & 1900 seriesS i z e s # Colors

1/2 oz. b o t t l e s 5 8

3 oz. s p ray 2 5


1/2 oz. b o t t l e s 1 2 1


1/2 oz. b o t t l e s 3 7

3 oz. s p ray 3 6

D e s c r i p t i o n :

Model Master professional enamel paintsa re specially formulated for airbrushing, a n dthe most popular colors are packaged in 3 oz.s p ray cans. T h e re are two series of paints:the FS enamel system for the discerningm i l i t a ry modeler, and the custom car linefor the re a l i s t i c p rofessional look. The FScolors are guaranteed to match corre s p o n d i n gU.S. Government Federal Standards 595Bcolor chips for military colors.

As with other fine Testor enamels, a l lcolors are produced i n - h o u s e a l l o w i n gus to monitor each batch as to color- m a t c h ,

o p a c i t y, v i s c o s i t y, e t c . Model Master enamelscan be used on many surfaces includingp o l y s t y rene plastic, ABS plastic, s t y ro f o a m ,g l a s s ,p l e x i g l a s s , wo o d ,m e t a l ,l e a t h e r. T h eywill not adhere to polye t hylene or polypro pyl e n e.It is also not recommended for rubber, o rflexible types of viny l , because it will notd ry on these surfaces; it will remain tacky tothe touch.

U s a ge / Ti p s :



2 ) D ry time: depends on thickness andc o n d i t i o n s , shown are appro x i m a t e s :F l a t s 30 min. to 1 hourGloss & Semi-gloss 1 hour to touch,full cure is 4872 hours.


3 ) When brushing, use long strokes in oned i re c t i o n , to minimize brush marks.


Thinning of flat enamels: start at 3parts paint to 1 part thinner.



M o d e l M a s t e r E n a m e l sEnamels

6 ) If masking with PARAFILM M, re m ov eafter 1 hour when airbrushing, 48 hourswhen using aerosol spray.

7 ) When clear-coating over metallics, i . e ,c h ro m e ,s i l v e r, c o p p e r, a l u m i n u m , d onot use Clear Top Coat Enamel!The enamel will deleaf or dull them e t a l l i c s . Instead use Glosscote o rDullcote Lacquer! You can also useclear acry l i c s , or Future floor wa x ,a sthese will not diminish the re f l e c t a n c eof the metallics.


9 ) To achieve a matte or semigloss finish,mix 50% gloss and 50% flat together.

10 ) To achieve a tra n s p a rent finish, m i x50% enamel with 50% gloss or flat clear.


1 2) Do not use Pa c t ra Formula U FuelP roofer over enamel finishes.

13 ) To bring out the fluorescent colors, abase coat of white needs to be appliedto the substra t e .F l u o rescent colors arenot phosphorescent,and will fade ifexposed to UV ray s .

1 4 ) To create a finer mist in aerosol cans,place the can in a shallow pan of wa r mwater for approximately 2 minutes. B e f o rea p p l i c a t i o n , shake can vigorously andt h o ro u g h l y.

1 5 ) If a flat enamel is not as flat as desire d ,pour out only the amount re q u i red atone time, into a separate container. A d da little bit of talc powder and flatten toyour liking. Remaining mixed enamelshould be disposed of pro p e r l y.

1 6 ) When using tra n s p a rent or semi-t ra n s p a rent colors, the substra t e s colorwill affect the finishs color and hue, i fthe substrate color is not neutra l i z e d .

1 7 ) To prevent gelling or eva p o ration in thebottle during long-term storage,cleanoff rim of bottle and inside of cap, t i g h t l yclose cap and invert bottle to wet thecap liner; when this dries, it will form aseal that reduces oxygen diffusion intothe bottle.



2 0 ) To re m ove clear lacquers, use rubbinga l c o h o l . The alcohol will not re m ov eenamels or attack decals.

2 1 ) M a ny modelers prefer a 1:1 paint/thinner ra t i o , especially when spray i n gcar bodies using enamels, f o l l o w e dby an ov e rall light mist application ofs t raight Airbrush Thinner to m e l d the paint finish and boost the glossiness.Give this one a try.

52700 series( b o t t l e s )

52900 series( s p ray s )

S i z e s # Colors1/2 oz. b o t t l e s 2 0

3 oz. s p ray s 9


Exclusively licensed to Te s t o r, a ra i n b o wof the richest pearlescent and solid hot ro dcolors from the palette of legendary hot ro ddesigner Boyd Coddington.

As with the Model Master line of customcar colors, B oy d s pearlescent paints can bechanged in hue to an infinite degree of color,just by changing the underlying base coat.All colors are produced i n - h o u s e a l l o w i n gus to monitor each batch as to color- m a t c h ,o p a c i t y, v i s c o s i t y, e t c .B oy d s enamels can beused on many surfaces including polystyre n ep l a s t i c , ABS plastic, s t y ro f o a m ,g l a s s ,p l e x i g l a s s,wo o d ,m e t a l ,l e a t h e r. B oy d s enamels will nota d h e re to polye t hylene or polypro py l e n e . It isalso not recommended for rubber, or flexibletypes of viny l , because it will not dry on thesesurfaces; it will remain tacky to the touch.

U s a ge / Ti p s :



2 ) D ry time: depends on thickness and

c o n d i t i o n s , shown are appro x i m a t e s :F l a t s 30 min. to 1 hourG l o s s 1 hour to touch, full cureis 4872 hours.


3 ) When brushing, use long strokes in oned i re c t i o n , to minimize brush marks.


Thinning of flat enamels: start at3 parts paint to 1 part thinner.



6 ) If masking with PARAFILM M, re m ov eafter 1 hour when airbrushing, 4 8hours when using aerosol spray.

7 ) When clear-coating over metallics, i . e . ,c h ro m e ,s i l v e r, c o p p e r, a l u m i n u m ,do not use Clear Top Coat Enamel!The enamel will deleaf or dull them e t a l l i c s . Instead use Glosscote orDullcote Lacquer! You can also useclear acry l i c s , or Future floor wa x ,a sthese will not diminish the re f l e c t a n c eof the metallics.


9 ) To achieve a matte or semigloss finish,mix 50% gloss and 50% flat together.

B o y d s C u s t o m C a r E n a m e l sEnamels

10 ) To achieve a tra n s p a rent finish, m i x50% enamel with 50% gloss orflat clear.


12 ) Do not use Pa c t ra Formula U FuelP roofer over enamel finishes.

13 ) To bring out the fluorescent colors, abase coat of white needs to be appliedto the substra t e .F l u o rescent colors arenot phosphore s c e n t , and will fade ifexposed to UV ray s .

14 ) To create a finer mist in aerosol cans,place the can in a shallow pan ofwarm water for approximately 2m i n u t e s .B e f o re application, s h a k ecan vigorously and thoro u g h l y.

1 5 ) If a flat enamel is not as flat as desire d ,pour out only the amount re q u i red atone time, into a separate container. A d da little bit of talc powder and flatten toyour liking. Remaining mixed enamelshould be disposed of pro p e r l y.

16 ) When using tra n s p a rent or semi-t ra n s p a rent colors, the substra t e s colorwill affect the finishs color and hue, i fthe substrate color is not neutra l i z e d .

17 ) To prevent gelling or eva p o ration inthe bottle during long-term stora g e ,clean off rim of bottle and inside ofc a p, tightly close cap and invert bottleto wet the cap liner; when this driesit will form a seal that reduces oxygendiffusion into the bottle.



2 0 ) To re m ove clear lacquers, use rubbinga l c o h o l . The alcohol will not re m ov eenamels or attack decals.

1400 series

S i z e s # Colors

1/2 oz. b o t t l e s 1 5

3 oz. s p ray 6


Model Master MetalizerT M is a modifiedl a c q u e r-based metalizing coating thatp roduces a plated looking surface speciallyformulated for plastic models. The Metalizersystem consists of a wide range of buffingand non-buffing colors which allows themodeler to duplicate natural metal finishes.

Buffing Metalizer contains minimal binderor resin solids, and maximum metal contentalong with a parafin wax that allows thebuffing that produces the metal plate look.

Non-Buffing contains more alcohol andbinder which does not re q u i re buffing.

Metalizer is also easy to use; all colorsa re premixed for airbrushing (spray re a dy )o n l y. T h e re are also 6 buffing aerosols tochoose fro m .

U s a ge / Ti p s :


1 ) Best conditions for use: 7080 degrees F,m o d e rate relative humidity.

2 ) Shake and stir thoroughly before use.

3) When using buffing metalizer, b u i l dup the finish by applying light mistcoats; after last coat let dry at least 15minutes before buffing.Buff with afacial tissue, cotton ball, or a soft cloth;when buffing, start with a light circ u l a rm o t i o n ,g radually i n c reasing pre s s u reas the surface starts to buff up t othe desired finish.

4 ) Allow Buffing Metalizers Exhaust,Dark Andontic Gray, Burnt Metal andGun Metal to dry at least 1 hour beforeb u f f i n g , Titanium 30 minutes. A l l o wnon-buffing metalizers to dry 15minutes before handling.

M o d e l M a s t e r M e t a l i z e r sLacquers

5 ) Non-Buffing Metalizers are not ava i l a b l ein aerosol form, only 1/2 oz. b o t t l e s .

6 ) Thinning of Metalizers is not necessary,but if desire d , use specially formulatedModel Master Metalizer T h i n n e r. L a c q u e rthinners can also be used to clean air-b r u s h . Do not use regular enamel ora c rylic type thinners, as Metalizer is amodified lacquer-based coating.

7 ) Do not mix the buffing and non-buffingcolors together in their liquid forms, a st h ey are of different formulations.

8 ) When masking over metalizers, u s eeither wet masking or PARAFILM M.Wet masking is strips of newsprint typep a p e r, soaked in water and applied tothe area to be painted; excess water issoaked up with an absorbent material,and the area is lightly airbrushed.

9 ) To protect your Metalizer finish useModel Master Metalizer Sealer; thisseals the finish to prevent fingerprints.As these heavy leafing metallics tendto rub off quite easily on your hand,be care f u l . Other lacquer-based clearswill work also. So as not to diminishthe shine, the sealers should be appliedin light mist coats that build up thep rotective coating.

1 0 ) Use regular enamel thinner to re m ov ebuffing colors in laye r s . Use lacquerthinner to re m ove non-buffing colors.Rubbing alcohol will re m ove both thebuffing and non-buffing metalizers.

S i z e s # Colors

2/3 oz. b o t t l e 2 9

3 oz. s p ray 3 5

2/3 oz. T h i n n e r

3 1/2 oz. T h i n n e r

1/2 pt. T h i n n e r


Pa c t ra RC Finishes are specially formulatedflexible Vi nyl A c rylic Lacquers, made to bes p rayed on the inside of clear Lexan bodies(only) of remote control cars. Being flexible,the paint does not tend to crack or peelwhen the Lexan body is flexed or bent.

U s a ge / Ti p s :


1 ) Best application conditions: 7080d e g rees F, low to moderate humidity.

2 ) When applied at or above 60% re l a t i v eh u m i d i t y, the paint may develop somecloudiness as it dries. This is called ahumidity blush or hazing.

3 ) When spraying aerosol colors, a p p l yin mist coats to avoid runs and sags.Especially when applying tra n s l u c e n tc o l o r s , as they will tend to show theruns and sags clearer than opaques.

4 ) D ry time is 510 minutes between coats;sanding is not re q u i re d .

5 ) A l ways use RC thinner to thin RCc o l o r s . If airbrushing, start thinning ra t i oat 9 parts paint to 1 part thinner. A d j u s tto your personal pre f e re n c e .

6 ) Use PARAFILM M or vinyl electricaltape as a mask.

7 ) When cleaning up dried paint out ofa i r b r u s h e s , use RC thinner. If not ava i l-a b l e , use a lacquer thinner which has aketone or ester base, such as acetone,M E K , or isopro pyl acetate.

8 ) To reduce eva p o ration of solventsf rom bottles during brush application,we recommend pouring out a smallamount of paint into a separate contain-er and recapping bottle. Do not re t u r nused paint to bottle after use!

9 ) C l o u dy appearance on clear Lexanb o dy may be a result of using too stro n gof a solvent or thinner.

1 0 ) RC film can be re m oved using a 50/50mix of RC Thinner and isopro pyl alcohol.

P a c t r a R C F i n i s h e s ( V i n y l A c r y l i c L a c q u e r s )Lacquers

99000 series

S i z e s # Colors

1/2 oz. b o t t l e s 1 4 0

1 oz. b o t t l e s 4

4 oz. b o t t l e T h i n n e r

4 oz. c a n C o n c e n t rated Cleaner


The New Model Master A c rylic Ure t h a n eEnamels a re fast dry i n g ,d u ra b l e , wa t e rwa s h - u p, gloss and flat coatings, d ev e l o p e dspecifically for superior adhesion to poly-s t y rene plastic. Model Master A c rylics comein a wide variety of colors. Just like ourenamel FS System, the acrylics have beenmatched to the Federal Standards 595B colorc h i p s , as well as A NA ,R L M , and RALs t a n d a rd s . We also include a selection ofour popular car colors and clear ov e rc o a t s .Along with the paints, we have an acry l i cthinner and cleaning solution.

U s a ge / Ti p s :




3 ) Use the acryl thinner only to thin forairbrush usage. Do not use water!!

4 ) Thinning ratios to start with arerecommended as follows: 7 parts paintto 3 parts thinner for gloss colors, 1 2 / 1to 7/3 paint to thinners for the flats.

5 ) Caution!! Overthinning will pro d u c einferior results (poor adhesion, c ov e ra g e ,and finish).

6 ) Depending on conditions, M o d e lMaster gloss acrylics will dry to thetouch in approximately 45 minutes,while the flats will t a c k in about halfthat time. Full cure takes appro x i m a t e l y24 hours.

7 ) Allow a minimum of four hours drytime before recoating with acry l i c s .

8 ) Mask acrylics with either PARAFILM Mor vinyl electrical tape.

9 ) Clean dried paint from airbrushesand regular brushes with Model MasterA c ryl Cleaner or hot lacquer thinner(R/C or A e ro - G l o s s ) .

1 0 ) To re m ove dried acrylic paint fro mm o d e l , combine 1 part A c rylic Cleanerto 1 part isopropanol (isopro pyl alcohol).You may use rubbing alcohol instead ofi s o p ro p a n o l .R e m ove film in laye r s .

Important Note:

The new Model Master A c ryl paint systemhas been developed from a far more superiorformula than the o r i g i n a l Model Mastera c ry l i c s , and as such, the Model Master A c ry lpaints are in no way compatible with theoriginal paints. Do not combine colors, w e tor dry, f rom the two systems. The ModelMaster A c ryl should be thinned, when neces-s a ry, with Model Master A c ryl T h i n n e r, n o tthe A c rylic Enamel Thinner associated withthe original acry l i c s .

M o d e l M a s t e r A c r y l ( N e w F o r m u l a )Acrylics

50100 series

50400 series

S i z e s # Colors

1/2 oz. b o t t l e s 6 3

1 oz. b o t t l e s 2 0

4 oz. b o t t l e T h i n n e r

4 oz. c a n C o n c e n t rated Cleaner


Model Master A c rylic Urethane Enamelsa re fast dry i n g ,d u ra b l e , water wa s h - u p,gloss and flat coatings, d eveloped specificallyfor superior adhesion to polystyrene plastic.Model Master A c rylics come in a wide va r i e t yof colors. Just like our enamel FS System,the acrylics have been matched to the Federa lS t a n d a rds 595B color chips. We also includea selection of our popular car colors and clearov e rc o a t s . Along with the paints, we have ana c rylic thinner and cleaning solution.

U s a ge / Ti p s :




3 ) Use the acryl thinner #50499 onlyto thin for airbrush usage. Do notuse water!!


5 ) Caution!! Overthinning will pro d u c einferior results (poor adhesion, c ov e ra g e ,and finish).

6 ) Depending on conditions, M o d e lMaster gloss acrylics will dry to thetouch in approximately 90 minutes,while the flats will t a c k in about halfthat time. Full cure takes appro x i m a t e l y24 hours.

7 ) Allow a minimum of four hours dry time before recoating with acry l i c s .


9 ) Clean dried paint from airbrushesand regular brushes with Model MasterA c rylic Cleaner or hot lacquer thinner(R/C or A e ro - G l o s s ) .


M o d e l M a s t e r A c r y l i c s ( O r i g i n a l F o r m u l a )Acrylics

S i z e s # Colors

2/3 oz. b o t t l e 6 1


Pa c t ra A c rylics are a wa t e r-based enamelthat adheres to most surfaces: polystyre n e ,m e t a l , wo o d ,g l a s s ,s t y ro f o a m ,e t c . One ofthe original A c ry l i c s , this formula has beena round for over 25 years!

U s a ge/ Ti p s :


1 ) Best conditions for use: 70-80 degre e sF, m o d e rate relative humidity.


3 ) Use the acrylic thinner #50499 onlyto thin for airbrush usage. Do notuse water!!


5 ) C a u t i o n ! ! Overthinning will pro d u c einferior results (poor adhesion, c ov e ra g e ,and finish).

6 ) Depending on conditions, Model Mastergloss acrylics will dry to the touch ina p p roximately 90 minutes, while the flatswill t a c k in about half that time. F u l lc u re takes approximately 24 hours.

7 ) Allow a minimum of four hours dry timeb e f o re recoating with acry l i c s .


9 ) Clean dried paint from airbrushes andregular brushes with Model MasterA c rylic Cleaner #50498 or hot lacquerthinner (R/C or A e ro - G l o s s ) .


P a c t r a A c r y l i c sAcrylics

# 1159 & #2018 Lacquer Thinner

(1 oz. b o t t l e s )

#1959 Clear Satin

(3 oz. s p ray )

# 2 0 1 6 Semi Gloss

(1 oz. b o t t l e )

# 1160, 1260 & #1960, #2015 Dullcote

(1 & 1 3/4 oz. bottles & 3 oz. s p ray )

# 1161, 1261 & #1961,#2017 Glosscote

(1 & 1 3/4 oz. bottles & 3 oz. s p ray )


G l o s s c o t e and D u l l c o t e a re lacquer- b a s e dclear ov e rc o a t s , used to seal and pro t e c tpainted surfaces.

D u l l c o t e is used for altering glossy surfaces togive them the flat look, and to protect decals.

Clear Satin is a semigloss or matte finish.50% Gloss, 50% Flat. ( s p ray only)

G l o s s c o t e is used for a smooth glossy finish,over flat paint for good decal adhesion, or fora smooth and shiny protective laye r.

U s a ge / Ti p s :


1 ) Best conditions for use: 7080 degrees F.Low relative humidity.


3 ) Can be used over all Te s t o r / Pa c t raenamels and acry l i c s , when latter hav edried at least 24 hours or more .

4 ) Can also be used over Te s t o r / I t a l e r idecals prior to submersion in wa t e r.Lacquers hold decal together betterduring placement on model. A l way stest for compatibility on competitorsp ro d u c t .

5 ) Allow decals to dry 24 hours beforea p p l y i n g .

6 ) Apply in mist applications until desire deffect is achiev e d .

7) To create a finer mist with aerosolc a n s , place can in shallow pan of wa r mwater for approximately 2 minutes.

8 ) When airbrushing, thin down lacquerswith Lacquer Thinner/Brush Cleaner;use 3 parts lacquer to 1 part thinner.Also use Thinner/Cleaner to cleanairbrush after usage.

9 ) Testor\Italeri decals markings do nota d h e re well to bare polystyre n e . If yo up refer to apply decals directly to poly-styrene,Glosscote should be appliedfirst; once the decal has dried thoro u g h l y,ov e rc o a t , to seal decal.

1 0 ) To re m ov e , gently rub down modelusing a soft cloth or cotton balls,s a t u rated with isopro pyl alcohol. It willre m ove lacquer film without harmingdecals or painted surface.

11 ) Should not be used over Ta m i ya acry l i c s .

C l e a r L a c q u e r F i n i s h e sFinishes

#1814 High Gloss Clear

(3 oz. s p ray )

#2736 & #2936 Clear Top Coat

(1/2 oz. bottle & 3 oz. s p ray )

#2944 Gloss Pearl Clearc o a t

(3 oz. s p ray )

#52720 High Gloss Clearc o a t

(1/2 oz. b o t t l e )

U s a ge / Ti p s :



2 ) D ry time: depends on thickness andc o n d i t i o n s , shown are appro x i m a t e s :

G l o s s 1 hour to touch, full cure is4872 hours.


3 ) When brushing, use long strokes inone dire c t i o n , to minimize brush marks.

4 ) Thinning of clear enamels start at3 parts paint to 2 parts thinner.


5 ) When airbrushing or aerosol spray i n g ,apply paint in sev e ral mist applicationsfirst,letting tack between coats; thisbuilds up a base for the final heavy coat,which will minimize sags and runs.

6 ) If masking with PARAFILM M, re m ov eafter 1 hour when airbrushing, 48 hourswhen using aerosol spray.

7 ) When clear-coating over metallics, i . e . ,c h ro m e ,s i l v e r, c o p p e r, a l u m i n u m ,do not use Clear Top Coat Enamel!The enamel will deleaf or dull them e t a l l i c s . Instead use Glosscote orDullcote Lacquer! You can also use ourclear acrylics #50160 or #50161, as thesewill not diminish the reflectance of them e t a l l i c s .

C l e a r E n a m e l F i n i s h e sFinishes

#50160 Clear Flat

(1/2 oz. bottle)

#50161 Clear Gloss

(1/2 oz. b o t t l e )


Model Master A c rylic Urethane Clearc o a tEnamels are fast dry i n g ,d u ra b l e , wa t e rwa s h - u p, gloss and flat coatings, d ev e l o p e dspecifically for superior adhesion to poly-s t y rene plastic.

U s a ge / Ti p s :




3 ) Use the acrylic thinner only, to thinfor airbrush usage. Do not use water!!

4 ) Thinning ratios to start with arerecommended as follows:

7 parts paint to 3 parts thinner (7/3)for gloss colors

12/1 to 7/3 paint to thinners forflat colors

5 ) C a u t i o n ! ! Overthinning will pro d u c einferior results (poor adhesion, c ov e ra g e ,and finish).

6 ) Depending on conditions, Model MasterClear Gloss A c rylics will dry to the touchin approximately 90 minutes, while theflats will t a c k in about half that time.Full cure takes approximately 24 hours.

7 ) Allow a minimum of four hours drytime before recoating with acry l i c s .


9) Clean dried paint from airbrushesand regular brushes with Model MasterA c rylic Cleaner or hot lacquer thinner(R/C or A e ro - G l o s s ) .


C l e a r F i n i s h f o r A c r y l i c sFinishes

Regular & Non-To x i c

5/8 & 7/8 oz. tubes

Liquid Cement

7/8 oz. ( N o n - Toxic Precision A p p l i c a t o r )

1 oz. (Bottle)

1 . 1 5 o z .( P recision A p p l i c a t o r s )

Cement Pens

1/3 oz. (Liquid Cement Pe n s )


Testor cements have been used byh o b byists and craftsmen for more than 60ye a r s . Specially formulated for polystyre n e ,ABS plastics, a c e t a t e ,p l e x i g l a s s , and manyother surfaces, Testor cements create excep-tionally strong and durable bonds.

U s a ge / Ti p s :


1 ) Plastic cements do not adhere well topainted surfaces; re m ove paint downto bare plastic before cementing.

2 ) USE SPA R I N G LY ! ! O v e ra p p l i c a t i o nm ay dissolve polystyrene parts.

3 ) After applying cement, p ress and holdparts together for approximately 1530seconds to maximize bond dev e l o p m e n t .

4 ) D ry time will va ry depending on amountused and env i ronmental conditions.H o w ever normal dry times are as follows:

2 hours for regular tubed and liquidc e m e n t s .

3 hours for cement pens.

4 hours for non-toxic cements.

5 ) Apply tubed cements with either ab r u s h ,t o o t h p i c k , or precision glue tips,to obtain a precise bead of cement.

6 ) Cement pens should be used on smalldetail are a s , as the solvent eva p o ra t e stoo rapidly on large are a s .

7 ) The cements listed above should notbe used on clear styrene parts. I n s t e a duse Testor Clear Styrene Cement.

8 ) The above cements can be re m ov e df rom clothing and other non-Styre n esurfaces by dabbing nail polish re m ov e ron affected area with a clean cloth.Place absorbent cloth underneath.

P l a s t i c H o b b y C e m e n t s Cements

Extra Fast

5/8 oz. t u b e # 3 5 0 3

1 3/4 oz. t u b e # 3 5 0 4

F a s t

5/8 oz. t u b e # 3 5 0 5

1 3/4 oz. t u b e # 3 5 0 6

Clear Parts

1 oz. ( P recision A p p l i c a t o r )


Testor Wood Cement comes in 2 differe n tsizes and types: a fast setting adhesive fors t rong bonds and the extra fast setting forquick bonds. Testor Wood Cements are spe-cially formulated to bond all types of wo o d ,m e t a l ,g l a s s ,c e ra m i c s , and untreated leathers.

Testor Clear Parts Adhesive is a pre m i u mnon-solvent white glue formula, for cement-ing clear parts onto a model without cra z i n g( c a n o p i e s , windshields etc). It is also packagedin our Precision Applicator for ease of appli-c a t i o n .

U s a ge / Ti p s :


Wood Cement

1 ) The extra fast wood formulationshould be used for quick repairs only,as it does not cure as strong as theslower curing type.

2 ) D ry time will va ry depending on amountof application and env i ronmental condi-tions: tempera t u re ,h u m i d i t y, e t c .

3 ) H o w ev e r, normal time re q u i red foroptimum bond is as follows:

Wood Extra Fast 6 hours

Wood Fast 12 hours

Clear Glue 4 hours

4 ) Depending on substra t e , wood cementm ay be re m oved with nail polishre m over that contains acetone.

Clear Parts Cement

1 ) Clear Parts Cement is a wa t e r- b a s e da d h e s i v e .

2 ) Clear Parts Cement will not mar ordissolve polystyrene parts.

3 ) You can make small windows by dippinga paint brush in cement, then make aswirling motion inside of window fra m e ,being sure to touch all sides as you swirlthe brush.Then re m ove the brush, m a k i n gs u re the cement is a continuous thin cov e rbridging the entire window opening.

4 ) R e m oval: after it has dried, it shouldpeel off. It is difficult to re m ove from flatpainted surfaces. R e m oves easily fro mgloss coatings and bare polystyre n e . Alittle rubbing alcohol on a cotton swa bwill do.

W o o d / C l e a r H o b b y C e m e n t s Cements

C y a n o a c r y l a t e

1/4 oz. bottle

Cyanoacrylate Accelerator

1/2 oz. s p ray


Testor Cyanoacrylate Instant Adhesive( s u p e rglue) is for those hard-to-bond spots,as it cures in 1020 seconds. Along withthe adhesive, we also have a Cya n o a c ry l a t eA c c e l e rator which cures the superglue instantly.

U s a ge / Ti p s :


1 ) Instant cements do not adhere well topainted surfaces; re m ove paint downto bare plastic before cementing.

2 ) Shake well before use!

3 ) Apply small drops of adhesive toone surface and carefully press partst o g e t h e r.

4 ) For large seams, apply drops 1/4 t o1 / 2 a p a r t .

5 ) To re m ove instant glue from handsor models, use netromethane orn e t ro p ro p a n e .

6 ) Use for bonding disimiliar materials,i . e . , plastic to brass photo-etched parts;plastic to wood; vinyl to metal; etc.

I n s t a n t H o b b y C e m e n t s Cements

U s a ge / Ti p s :


1 ) A p p roximate mixing ra t i o s :G l o s s 3 parts paint to 2 parts thinner*F l a t s 3 parts paint to 1 part thinner


2 ) Use airbrush thinner only for thinningenamel paints to airbrush, and cleaningout airbrush and tips. Do not use as wa s h !This formulation is too aggressive andwill attack previously painted coats.

3 ) For wa s h e s , use Enamel Brush Cleaner,as this formulation is not as aggre s s i v e ,and has less tendency to attack prev i o u spainted coats.

* M a ny modelers prefer a 1:1 paint/thinnerra t i o , especially when spraying car bodiesusing enamels, followed by an ov e ra l llight mist application of straight A i r b r u s hThinner to m e l d the paint finish andboost the glossiness. Try it, youll like it.

Airbrush Thinners

1/2 pt. c a n

1 3/4 oz. b o t t l e s

Model Master Thinner

1/2 pt. c a n

1 3/4 oz. b o t t l e

Brush Cleaners

1/4 oz. b o t t l e

1 3/4 oz. b o t t l e


Testor Enamel Thinners come in a va r i e t yof sizes with 2 different formulations: one forairbrushing and one for cleaning brushes.The airbrushing thinner is a stronger solventthat should be used as a paint thinner,airbrush cleaner only!

Use the brush cleaner for wa s h e s , as it willnot attack the substrate as aggressively asthe airbrush thinner. It is also re c o m m e n d e dto use only Testor thinners in Testor paintp ro d u c t s , because it is specially formulated forthis purpose.

E n a m e l T h i n n e r sAccessories

#8804 Decal Setting Solution

1/4 oz. b o t t l e

#2145 Decal Solvent Solution

#2146 Decal Setting Solution

1/2 oz. b o t t l e s


Testor newly developed blends of decalsolvents come in both the 1/4 and 1/2 oz.s i z e s . As with other popular decal solutions,Testor solutions come in both a Setting andSolvent Solution. The Setting Solution isused for decal placement over panel linesand pro t r u s i o n s , allowing the decal to stre t c hand conform to irregular surfaces.SettingSolution also allows you to move the decalafter you have applied it to the surface, f o rp recision placement. Testor Decal Solventis for those hard-to-decal areas: corners,wing ro o t s , and other areas where the settingsolution does not seem to work well. S o l v e n tis specially designed to be put on only onceand not touched until dry, as it tends to makethe decal extremely susceptible to damage.But the good part is, it stretches and conformsto extremely irregular surfaces, and hugsdown tight when dry.

N O T E : #2146 Decal Setting Solution(MMII) is a stronger formulation than the1/4 oz. #8804 Decal Solution.

U s a ge / Ti p s :


1 ) Apply decals to model as directed ini n s t r u c t i o n s .

2 ) Blot dry decal with soft cloth, m a k i n gs u re to press out air bubbles.

3 ) Apply Decal Setting Solution with smallp a i n t b r u s h .S p read evenly! Let dry.

4 ) If applying Solvent Solution, make suredecal is in desired position before apply-i n g . Apply same way as Setting Solution.Do not touch the decal until thoro u g h l yd ry (24 hrs), or you may risk damaging it.

5 ) Both solutions may be re - a p p l i e dre p e a t e d l y, if necessary, until the desire dresult is obtained.

6 ) Solvent and Setting Solutions also wo r kwell for re m oving decals. Apply libera l l yand let soak in for a few minutes; oncedecal softens, re m ov e .

D e c a l S o l u t i o n sAccessories

Model Master # 50641

2 x 25 R o l l


PARAFILM M is a thin, l o w - t a c ,s t re t c h a b l e ,e a s y - t o - u s e ,s e l f - a d h e s i n gmasking material. It is ideal for masking compound curves and hard-to-mask are a s .PARAFILM M also works well on complexcamouflage schemes, custom car paints c h e m e s , and for detail painting of s m a l lintricate parts. The advantage of PA R A F I L MM over traditional masks is that its thinnessminimizes the paint thickness b r i d g e o r d a m that sometimes occur betweenadjacent colors.

U s a ge/ Ti p s :


1 ) Cut PARAFILM M to desired lengthand re m ove backing paper.

2 ) Hold at both ends and stretch piece to4 or 5 times its length. This stre t c h i n gthins and activates the wax surface soit becomes tacky.

3 ) L ay pre p a red PARAFILM M o n t osurface to be masked. Gently press itdown; do not use burnishing tool asthis may damage the PARAFILM M.

4 ) Ve ry lightly, trim PARAFILM Mwith sharp hobby knife to desire dp a t t e r n . Gently re - p ress cut edge downonto surface.

5 ) A l ways spray vertically or at a slightangle away from masking material asto avoid building paint up too thicklyalong edge of masking.

6 ) Allow paint to dry before slowlyre m oving PARAFILM M m a s k .

7 ) N e v e r b r i d g e PARAFILM M a c ro s sa gap and then push it down, relying onits stretch to fill a large ra d i u s .You mustwork the PARAFILM M f rom ones u r f a c e , into the fillet and then up theintersecting wa l l .

P a r a f i l m M M a s k i n g M a t e r i a lAccessories

Documents

Testors Product Guide