Embed Size (px)
Citation preview
1 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
TEL: +2711 952 9800 WWW.KLAMBON.COM
2 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
Klambon Water is a wholly owned subsidiary of West Rand Engineering (WRE), we are suppliers of valves, fittings and
related products to all industries and our service extends to customers throughout the world.
WRE was established in 1928 to cater for the needs of the hard rock mining industry. Their range includes ‘GLEN’ ball
and butterfly valves and Wilco snatch blocks.
WRE acquired the business and property of Malleable Castings in April 2017. Malleable also trades as a division of
WRE enabling WRE to become a fully local, South African manufacturer of Valves, Fittings, Mining and related
products. Malleable have been a long-term supplier of castings to WRE and the synergistic benefits of the acquisition
enable Malleable to increase the capacity of the foundry with a huge localization drive from South African customers.
WRE also acquired the business of Africa Thermal Insulations (ATI) which now also trades as a division of West Rand
Engineering. ATI manufactures, sells, markets and distributes building insulation products including PVC
hose throughout Africa. We believe in green business and therefore we focus on the conservation of energy within
the building industry and we strive to operate our business in a way that eliminates waste and conserves natural
resources.
These businesses are managed out of our offices in Johannesburg, Cape Town and Sydney, Australia.
Klambon Water is perfectly positioned to serve the needs of all valued customers utilising the local expertise and
manufacturing capabilities of WRE, Malleable Castings and ATI.
3 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
Index
Section A – Glen Ball Valves
Female Thread to Female Thread
Shouldered to Female Thread
Shouldered
Flanged
Section B – Glen Butterfly Valves
Shouldered
Wafer
Section C – Clamps and Gaskets
Shouldered Clamps and Gaskets
Section D – Manifolds
Cast Shouldered
Fabricated
Section E – Fabricated Fittings
Shouldered and flanged
4 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
Index
Section F – Pipe Couplings
Wide Range
Wide Range Step
Dedicated
Dedicated Step
Gripper
Section G- Flanged Adaptors
Wide Range Flange
Dedicate Flange
Gripper Flange
Section H – Dismantling Joints
Dismantling joints
Section I – Quick Adaptors
Quick Adaptors for PVC and PE Pipes
Quick Adaptors for Ductile Iron Pips
5 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
Index
Section J – Valves and Strainers
Resilient Seal Socketed Gate Valve Non-Rising Spindle
Resilient Seal Flanged Gate Valve Non-Rising Spindle
Resilient Seal Flanged Gate Valve Rising Spindle
Metal Seated Gate Valve Non-Rising Spindle
Swing Check Valve
Y Strainer
Section K – Repair and Snap Clamp
Repair Clamp
Snap Clamp
Section L – Universal Tapping Saddle
Universal Tapping Saddle
Section M – Reducing Flanges
Reducing Flanged
Section N – Rubber Expansion Joints
Rubber Expansion Joints
Section O – PVC Hose-
Mining Hose SANS 1086 – 2007
Dragline Hose SANS 271 – 2005
PIPE OD Chart
6 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
• Floating Ball Design for improved sealing and higher pressure
• Bi-directional operation
• Compact valve with minimum parts
• Full bore design reduces turbulence and decreases pressure drop through
valve
• Robust cast body
• Spindle designed to prevent possibility of blow out
• Valve maintenance done in-situ
• Handles replaced easily by removing nut
SECTION A – GLEN BALL VALVES
FEMALE TO FEMALE THREAD
Handle Mild Steel
Spindle Stainless Steel
Seats Nitrile
Ball Stainless Steel
Fasteners 4.8 Carbon Nut and
Spring Washer
Body and Cap S.G Iron
Description A
mm
B
mm
C
mm
Working
Pressure
(kPA)
Working
Temperature
(°C)
15 mm ball valve with a 90° rotating handle, stainless steel spindle and
female to female BSP thread
85 75 75 3500 -20 to 80
20 mm ball valve with a 90° rotating handle, stainless steel spindle and
female to female BSP thread
93 95 110 5400 -20 to 80
25 mm ball valve with a 90° rotating handle, stainless steel spindle and
female to female BSP thread
110 105 115 5400 -20 to 80
32 mm ball valve with a 90° rotating handle, stainless steel spindle and
female to female BSP thread
135 120 125 5400 -20 to 80
40 mm ball valve with a 90° rotating handle, stainless steel spindle and
female to female BSP thread
145 175 250 4000 -20 to 80
50mm ball valve with a 90° rotating handle, stainless steel spindle and
female to female BSP thread
140 155 165 4000 -20 to 80
80 mm ball valve with a 360° rotating handle, mild steel spindle and female
to female BSP thread
255 225 195 3700 -20 to 80
MANUFACTURED IN SOUTH AFRICA
Specifications
Materials of Construction
7 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
• Floating Ball Design for improved sealing and higher pressure
• Bi-directional operation
• Compact valve with minimum parts
• Full bore design reduces turbulence and decreases pressure drop through
valve
• Robust cast body
• Spindle designed to prevent possibility of blow out
• Valve maintenance done in-situ
• Handles replaced easily by removing nut
SHOULDERED TO FEMALE THREAD
Handle Mild Steel
Spindle Stainless Steel
Seats Nitrile
Ball Stainless Steel
Fasteners 4.8 Carbon Nut and
Spring Washer
Body and Cap S.G Iron
DESCRIPTION A
mm
B
mm
C
mm
Working
Pressure
(kPA)
Working
Temperature
(°C)
50 mm shouldered to 25 mm female BSP thread ball valve with a 360°
rotating handle and a stainless steel spindle
120 115 135 5400 -20 to 80
50 mm shouldered to 25 mm female BSP thread ball valve with a 90°
rotating handle and a stainless steel spindle
120 115 135 5400 -20 to 80
50 mm shouldered to 25 mm female BSP thread ball valve with a 90°
lockable rotating handle and a stainless steel spindle
120 115 135 5400 -20 to 80
Specification Materials of Construction
MANUFACTURED IN SOUTH AFRICA
8 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
• Floating Ball Design for improved sealing and higher pressure
• Bi-directional operation
• Compact valve with minimum parts
• Full bore design reduces turbulence and decreases pressure drop through
valve
• Robust cast body
• Spindle designed to prevent possibility of blow out
• Valve maintenance done in-situ
• Handles replaced easily by removing nut
SHOULDERED
Handle Mild Steel
Spindle Stainless Steel
Seats Nitrile
Ball Stainless Steel
Fasteners 4.8 Carbon Nut and
Spring Washer
Body and Cap S.G Iron
DESCRIPTION A
mm
B
mm
C
mm
Working
Pressure
(kPa)
Working
Temperature
(°C)
48 mm shouldered ball valve with a 360° rotating handle with a stainless
steel spindle
250 175 250 4000 -20 to 80
50 mm shouldered ball valve with a 360° rotating handle with a stainless
steel spindle
180 205 250 4000 -20 to 80
80 mm shouldered ball valve with a 360° lockable rotating handle with
a stainless steel spindle
255 225 195 2700 -20 to 80
100 mm shouldered ball valve with a 360° lockable rotating handle with
a stainless steel spindle
280 285 195 2700 -20 to 80
Specifications Materials of Construction
MANUFACTURED IN SOUTH AFRICA
9 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
• Floating Ball Design for improved sealing and higher pressure
• Bi-directional operation
• Compact valve with minimum parts
• Full bore design reduces turbulence and decreases pressure drop through
valve
• Robust cast body
• Spindle designed to prevent possibility of blow out
• Valve maintenance done in-situ
• Handles replaced easily by removing nut
• Other drilling options available upon request
FLANGED
Handle Mild Steel
Spindle Stainless Steel
Seats Nitrile
Ball Stainless Steel
Fasteners 4.8 Carbon Nut and
Spring Washer
Body and Cap S.G Iron
DESCRIPTION A
mm
B
mm
C
mm
Working
Pressure
(kPa)
Working
Temperature
(°C)
50 mm table D flanged ball valve with a 360° rotating handle 175 178 255 4000 -20 to 80
80 mm table D flanged ball valve with a 360° rotating handle 223 190 215 2700 -20 to 80
100 mm table D flanged ball valve with a 360° rotating handle 266 275 195 2700 -20 to 80
Specifications Material of Construction
MANUFACTURED IN SOUTH AFRICA
10 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
• Designed to meet international standards
• Extremely rugged
• Simple to install and operate
• No lubrication necessary
• Low maintenance cost
• Throttling facility by using the optional multi-stop handle
• Easy adaptation to flanged pipe lines
• Corrosion and abrasion resistant
SECTION B – GLEN BUTTERFLY VALVES
SHOULDERED
Body Spheroidal Graphite Iron, FBE
Coated or NBR Lined
Disc Spheroidal Graphite Iron, Nitrile
Rubber Coated or 316 Stainless
Steel
Spindle Cast Iron or 316 Stainless Steel
Rubber Lining Nitrile Rubber (EPDM available )
SIZE DESCRIPTION A
(mm)
B
(mm)
C
(mm)
Pressure
(kPa)
Temperature
(°C)
50mm SH Shouldered butterfly valve with a 90° lever and stainless steel spindle 84 205 155 2500 -20 to 80
50mm SH Shouldered butterfly valve with a multi-stop lever and stainless steel spindle 115 305 230 2500 -20 to 80
100mm SH Shouldered butterfly valve with a 90° lever and cast iron spindle 115 275 230 2500 -20 to 80
100mm SH Shouldered butterfly valve with a 90° lever and stainless steel spindle 115 275 230 2500 -20 to 80
100mm SH Shouldered butterfly valve with a multi-stop lever and cast iron spindle 115 305 230 2500 -20 to 80
100mm SH Shouldered butterfly valve with a multi-stop lever and stainless steel spindle 115 305 230 2500 -20 to 80
100mm SH Shouldered butterfly valve with a hand wheel actuator and cast iron spindle 115 360 160 2500 -20 to 80
100mm SH Shouldered butterfly valve with a hand wheel actuator and stainless steel
spindle 115 360 160 2500
-20 to 80
150mm SH Shouldered butterfly valve with a 90° lever and cast iron spindle 150 350 310 2500 -20 to 80
150mm SH Shouldered butterfly valve with a multi-stop lever and cast iron spindle 150 370 310 2500 -20 to 80
150mm SH Shouldered butterfly valve with a multi-stop lever and stainless steel spindle 150 370 310 2500 -20 to 80
150mm SH Shouldered butterfly valve with a hand wheel actuator and cast iron spindle 150 420 160 2500 -20 to 80
150mm SH Shouldered butterfly valve with a hand wheel actuator and stainless steel
spindle 150 420 160 2500
-20 to 80
200mm SH Shouldered butterfly valve with a 90° lever and cast iron spindle 135 440 500 2500 -20 to 80
200mm SH Shouldered butterfly valve with a multi-stop lever and cast iron spindle 135 475 500 2500 -20 to 80
200mm SH Shouldered butterfly valve with a multi-stop lever and stainless steel spindle 135 475 500 2500 -20 to 80
200mm SH Shouldered butterfly valve with a hand wheel actuator and stainless steel
spindle 135 542 250 2500
-20 to 80
Specification Materials of Construction MANUFACTURED IN SOUTH AFRICA
11 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
• Designed to meet international standards
• Extremely rugged
• Simple to install and operate
• Handwheel handle available on request
• No lubrication necessary
• Low maintenance cost
• Throttling facility by using the optional multi-stop handle
• Easy adaptation to flanged pipe lines
• Corrosion and abrasion resistant
• Non-toxic WRAS approved gasket and coating
WAFER
Body Cast Iron
Shaft Stainless Steel
Disc Stainless Steel
Bushing PTFE
Liner EPDM
O-Ring EPDM
Coating Fusion Bonded Epoxy
Size A
(mm)
B
(mm)
C
(mm)
D
(mm)
E
(mm)
Φ Pressure (kPa)
Temperature (°C)
50 161 80 30 90 43 56.8 2000 -10°C to 120°C
80 181 95 30 90 46 83 2000 -10°C to 120°C
100 200 115 30 90 51.5 101.5 2000 -10°C to 120°C
150 225 138 30 90 56.5 151.1 2000 -10°C to 120°C
200 241 174 30 125 60 200.5 2000 -10°C to 120°C
250 296 198 30 125 68.5 251.3 2000 -10°C to 120°C
300 336 234 30 125 79.5 300.5 2000 -10°C to 120°C
Specifications
Material of Construction
MANUFACTURED IN SOUTH AFRICA
12 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SECTION C – CLAMPS AND GASKETS
CAST SHOULDERED CLAMPS
Size Pipe OD
(mm)
Working Pressure
(kPa)
Bolt Size
(mm)
OD
(mm)
ID
(mm)
L
(mm)
H
(mm)
50 60.3 4000 M12x65 97 61 132 48
100 114.3 3500 M12x90 156 115.6 206 52
150 165.1 3500 M16x115 212 167 273 52
200 219.1 3000 M16x115 280 221 346 60
250 273 2500 M16x115 342 275 416 64
ALTERNATIVE COLOURS ARE AVAILABLE UPON REQUEST
MANUFACTURED TO SANS 815
REPLACEMENT GASKETS AVAILABLE UPON REQUEST
REPLACEMENT FASTENERS AVAILABLE UPON REQUEST
MANUFACTURED IN SOUTH AFRICA
13 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
` SECTION D – MANIFOLDS
CAST SHOULDERED
DESCRIPTION
50mm SHOULDERED INLET
5X50mm SHOULDERED OUTLET
GALVANIZED
DESCRIPTION
100mm SHOULDERED INLET
5X50mm SHOULDERED OUTLET
GALVANIZED
DESCRIPTION
50mm SHOULDERED INLET
5X50mm SHOULDERED OUTLET
PAINTED
DESCRIPTION
100mm SHOULDERED INLET
5X50mm SHOULDERED OUTLET
PAINTED
MANUFACTURED IN SOUTH AFRICA
14 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
FABRICATED
DESCRIPTION
50mm SHOULDERED MANIFOLD
5X25mm BALL VALVE
DESCRIPTION
100mm SHOULDERED MANIFOLD
50mm BALL VALVE INLET
4X25mm BALL VALVE
DESCRIPTION
150mm TABLE “D” FLANGED MANIFOLD
1X50mm BALL VALVE
6X25mm KWIKFIT COMBI BALL VALVE
DESCRIPTION
200mm TABLE “D” FLANGED MANIFOLD
1X50mm BALL VALVE
6X25mm KWIKFIT COMBI BALL VALVE
MANUFACTURED IN SOUTH AFRICA
15 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SECTION E – FABRICATED FITTINGS
SHOULDERED
DESCRIPTION
DN50 - DN200 Nominal Bore Shouldered/ Flanged Equal T
DESCRIPTION
DN50-DN200 Nominal Bore Shouldered/ Flanged Unequal T
DESCRIPTION
DN50 - DN200 Nominal Bore Shouldered/ Flanged 90° Elbow
DESCRIPTION
DN50 - DN200 Nominal Bore Shouldered/ Flanged 90° Segmented Bend
DESCRIPTION
DN50 - DN200 Nominal Bore Shouldered/ Flanged 45° Elbow
MANUFACTURED IN SOUTH AFRICA
16 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
FLANGE DRILLED TO BS 4504; BSEN 1092; SANS 1123 AND BS10
DESCRIPTION
DN50 - DN200 Nominal Bore Shouldered/ Flanged 45° Segmented Bend
DESCRIPTION
DN50 - DN200 Nominal Bore Flanged to Shouldered Adaptor
DESCRIPTION
DN50 - DN200 Nominal Bore Shouldered/ Flanged Concentric Butt-weld Reducer
17 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SECTION F – PIPE COUPLINGS
WIDE RANGE
Sleeve DN50 - 300 Rolled Steel
Sleeve DN350 - 600 Ductile Iron
End Rings DN50 - 600 Ductile Iron
Gaskets EPDM
Fasteners Electro Galvanized
Alternative 316 Stainless Steel
Coating Fusion Bonded Epoxy
Specification
• Connect plain ended pipes of various outside diameter with the same or
different nominal bore
• Profiled gasket allowing for smooth installation
• Providing a leak tight seal across the outside diameter of the pipe
• Thermal expansion and contraction of 5mm per gasket
• Angular deflection of 5 degrees
• Non-toxic WRAS approved gasket and coating
Maximum Working Pressure
• 16 Bar
Corrosion Protection
• Fusion bonded epoxy
Notes
• Gaskets must be lubricated to allow ease of installation
• Design and materials are subjected to change without
prior notice
Materials of Construction
18 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
WIDE RANGE STEP COUPLING
Sleeve DN50 - 250 Rolled Steel
End Rings DN50 - 250 Ductile Iron
Gaskets EPDM
Fasteners Electro Galvanized
Alternative 316 Stainless Steel
Coating Fusion Bonded Epoxy
Specification
• Connect plain ended pipes of various outside diameter with the
same or different nominal bore
• Profiled gasket allowing for smooth installation
• Providing a leak tight seal across the outside diameter of the pipe
• Thermal expansion and contraction of 5mm per gasket
• Angular deflection of 5 degrees
• Non-toxic WRAS approved gasket and coating
Maximum Working Pressure
• 16 Bar
Corrosion Protection
• Fusion bonded epoxy
Notes
• Gaskets must be lubricated to allow ease of installation
• Design and materials are subjected to change without
prior notice
Materials of Construction
19 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
• Fusion bonded epoxy
DEDICATED COUPLING
Sleeve DN50 – 125NB Ductile Iron
Sleeve DN150 - 2400 Rolled Steel
End Rings DN50 - 300 Ductile Iron
End Rings DN350-2400 Rolled Steel
Gaskets EPDM
Fasteners Electro Galvanized
Alternative 316 Stainless Steel
Coating Fusion Bonded Epoxy
Specification
• Connect plain ended pipes to plain ended pipes with the same outside
diameter
• Profiled gasket allowing for smooth installation
• Providing a leak tight seal across the outside diameter of the pipe
• Thermal expansion and contraction of 5mm per gasket
• Angular deflection: DN50-450 (6°), DN500-600 (5°), DN600 – 750 (4°),
DN750-1200 (3°), DN1200-1800 (2°), DN1800 (1°)
• Non-toxic WRAS approved gasket and coating
• 16 Bar
Corrosion Protection
Notes
• Gaskets must be lubricated to allow ease of installation
• Design and materials are subjected to change without prior notice
• Sizes greater than DN2400 are available on request
• Pressures greater than 16 bar are available on request
Materials of Construction
Maximum Working Pressure
20 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
• Connect plain ended pipes to plain ended pipes with different outside
diameters
• Profiled gasket allowing for smooth installation
• Providing a leak tight seal across the outside diameter of the pipe
• Thermal expansion and contraction of 5mm per gasket
• Angular deflection: DN50-450 (6°), DN500-600 (5°), DN600 – 750 (4°),
DN750-1200 (3°), DN1200-1800 (2°), DN1800 (1°)
• Non-toxic WRAS approved gasket and coating
DEDICATED STEP COUPLING
Sleeve DN50 – 125 Ductile Iron
Sleeve DN150 - 2400 Rolled Steel
End Rings DN50 - 300 Ductile Iron
End Rings DN350-2400NB Rolled Steel
Profile Plate Steel
Gaskets EPDM
Fastener Bolts Electro Galvanized
Fastener Studs 316 Stainless Steel
Coating Fusion Bonded Epoxy
Specification
• 16 Bar
Corrosion Protection
• Fusion bonded epoxy
Notes
• Gaskets must be lubricated to allow ease of installation
• Design and materials are subjected to change without prior notice
• Sizes greater than DN2400 are available on request
• Pressures greater than 16 bar are available on request
Materials of Construction
Maximum Working Pressure
21 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
• Couplings are designed to resist end pull-out on PE and PVC pipes
• It is the fastening action of the Gripper Ring that secures the
coupling onto the pipe resisting end pull-out
• Profiled gasket allowing for smooth installation
• Non-toxic WRAS approved gasket and coating
GRIPPER COUPLING
Sleeve Ductile Iron
End Rings Ductile Iron
Gripper Ring Brass
Gaskets EPDM
Fastener Electro Galvanized
Alternative 316 Stainless Steel
Coating Fusion Bonded Epoxy
Specification
• 16 bar
Corrosion Protection
• Fusion bonded epoxy
Notes
• Gaskets must be lubricated to allow ease of installation
• Design and materials are subjected to change without prior notice Materials of Construction
Maximum Working Pressure
22 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SECTION G – FLANGE ADAPTORS
WIDE RANGE FLANGE ADAPTORS
Sleeve Ductile Iron
End Ring Ductile Iron
Flange Ductile Iron
Gaskets EPDM
Fasteners Electro Galvanized
Alternative 316 Stainless Steel
Coating Fusion Bonded Epoxy
Specification
• Connect plain ended pipes of various outside diameters to flanged
equipment
• Flange drilling to BS 4504; BSEN 1092; SANS 1123 and BS 10
• Profiled gasket allowing for smooth installation
• Providing a leak tight seal across the outside diameter of the pipe
• Thermal expansion and contraction of 5mm per gasket
• Angular deflection of 2 degrees
• Non-toxic WRAS approved gasket and coating
Maximum Working Pressure
• 16 Bar
Corrosion Protection
• Fusion bonded epoxy
• Gaskets must be lubricated to allow ease of installation
• Design and materials are subjected to change without
prior notice
Materials of Construction Notes
23 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
• 16 Bar
• Gaskets must be lubricated to allow ease of installation
• Design and materials are subjected to change without prior notice
• Sizes greater than DN2400 are available on request
• Pressures greater than 16 bar are available on request
DEDICATED FLANGED ADAPTORS
Sleeve DN50 – 125NB Ductile Iron
Sleeve DN150 - 2400 Rolled Steel
End Rings DN50 - 300 Ductile Iron
End Rings DN350-2400 Rolled Steel
Flange Steel Plate
Gaskets EPDM
Fasteners 316 Stainless Steel
Coating Fusion Bonded Epoxy
Specification
• Connect plain ended pipes to flanged equipment
• Flange drilling to BS 4504; BSEN 1092; SANS 1123 and BS 10
• Profiled gasket allowing for smooth installation
• Providing a leak tight seal across the outside diameter of the pipe
• Thermal expansion and contraction of 5mm per gasket
• Angular deflection: DN50-450 (3°), DN500-750 (2°), DN750-1200 (1°),
DN1200-1800 (1°), DN1800+ (0°)
• Non-toxic WRAS approved gasket and coating
Maximum Working Pressure
Corrosion Protection
• Fusion bonded epoxy
Notes
Materials of Construction
24 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
GRIPPER FLANGED ADAPTORS
Sleeve Ductile Iron
End Rings Ductile Iron
Flange Steel Plate
Gripper Ring Brass
Gaskets EPDM
Fasteners Electro Galvanized
Alternative 316 Stainless Steel
Coating Fusion Bonded Epoxy
Specification
• Couplings are designed to resist end pull-out on PE and PVC pipes
• It is the fastening action of the Gripper Ring that secures the coupling onto
the pipe resisting end pull-out
• Flange drilling to BS 4504; BSEN 1092 and SANS 1123
• Profiled gasket allowing for smooth installation
•
Maximum Working Pressure
• 16 bar
Corrosion Protection
• Fusion bonded epoxy
Notes
• Gaskets must be lubricated to allow ease of installation
• Design and materials are subjected to change without prior notice
Materials of Construction
25 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
• A composite fitting featuring a telescopic action, designed to
provide longitudinal adjustment between a flanged pipe and
flanged equipment
• Flange drilling to BS 4504; BSEN 1092; SANS 1123 and BS 10
• Provide a simple method for installation and removal of flanged
equipment such as valves and pumps
• Thickness of flanges will not necessarily be the same as the
mating flange
• Non-toxic WRAS approved gasket and coating
SECTION H – DISMANTLING JOINTS
DISMANTLING JOINTS
Sleeve DN50 - 200 Ductile Iron
Sleeve DN250 - 2400 Rolled steel
End Ring DN50 - 300 Ductile Iron
End Ring DN350 – 2400 Rolled Steel
Flange Steel Plate
Spigot Steel Plate and Rolled Steel
Gaskets EPDM
Fastener Studs 316 Stainless Steel
Alternative 316 Stainless Steel
Fastener Tie Rods Electro Galvanized
Alternative 316 Stainless Steel
Coating Fusion Bonded Epoxy
• Gaskets must be lubricated to allow ease of installation
• Design and materials are subjected to change without
prior notice
• Sizes greater than DN2400 are available on request
• Pressures greater than 16 bar are available on request
Specification
Maximum Working Pressure
• 16 Bar
Corrosion Protection
• Fusion bonded epoxy
Notes
Materials of Construction
26 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SECTION I – QUICK ADAPTORS
QUICK ADAPTORS FOR PVC AND PE PIPES
Sleeve Ductile Iron
Flange Ductile Iron
Gaskets EPDM
Gripper Ring Brass
Coating Fusion Bonded Epoxy
Specification
• Quick adaptors are used to connect PVC and PE pipes to
flanged equipment
• A Gripper Ring is introduced to connect PE pipes to Flanged
equipment.
• Flange drilling to BS 4504; BSEN 1092; SANS 1123 and BS 10
• 16 bar
Corrosion Protection
• Fusion bonded epoxy
Materials of Construction
Maximum Working Pressure
27 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
DN OD L (mm)
40 50 52
50 50 52
50 63 54
60 63 54
65 75 57
80 75 57
80 90 60
100 90 60
100 110 64
125 125 72
125 140 76
150 160 80
200 180 86
200 200 90
200 225 90
250 250 92
300 280 98
300 315 102
350 355 114
400 400 128
28 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
DN OD L (mm)
40 50 52
50 50 52
50 63 54
60 63 54
65 75 57
80 75 57
80 90 60
100 90 60
100 110 64
125 125 72
125 140 76
150 160 80
200 180 86
200 200 90
200 225 90
250 250 92
300 280 98
300 315 102
350 355 114
400 400 128
29 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
QUICK ADAPTORS FOR DUCTILE IRON PIPES
DN OD L (mm)
80 98 49
100 118 56
125 144 63
150 170 70
200 222 77
250 274 87
300 326 97
Sleeve Ductile Iron
Flange Ductile Iron
Gripper Teeth Carbon Steel
Gasket EPDM
Coating Fusion Bonded Epoxy
Specification
• Quick adaptors are used to connect Ductile Iron pipes to
flanged equipment by inserting teeth into the rubber
• Flange drilling to BS 4504; BSEN 1092; SANS 1123 and BS 10
Maximum Working Pressure
• 16 bar
Corrosion Protection
• Fusion bonded epoxy
Materials of Construction
30 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SECTION J – VALVES AND STRAINERS
RESILIENT SEAL SOCKETED GATE VALVE NON-RISING SPINDLE
DN (mm) L (mm) H (mm)
90 335 413
110 355 435
160 405 528
200 450 616
Body Ductile Iron
Bonnet Ductile Iron
Gland Ductile Iron
HW/Cap Ductile Iron
Stem Nut Bronze
Spindle Stainless Steel
Fastener Stainless Steel
Coating Fusion Bonded Epoxy
Specification
• Non-Rising Spindle
• Fusion-Bonded Epoxy Powder Coated
• EPDM Rubber-lined S.G Iron Gate
• Supplied Socketed
• Right or Left-Hand Closing
• Cap-Top or Hand Wheel Operated
• Wedge Coated to EPDM
• Face-to-Face length according to SABS 664
• Low Torque opening and closing
• 50-450mm Sizes available
Maximum Working Pressure
• 16 bar
Corrosion Protection
• Fusion bonded epoxy
Materials of Construction
31 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
RESILIENT SEAL FLANGED GATE VALVE NON-RISING SPINDLE
Body Ductile Iron
Wedge EPDM
Wedge Core Ductile Iron
Stem Nut Stem
Stem Stainless Steel
Gasket EDPM
Stud Stainless Steel
Bonnet Ductile Iron
O-Ring EDPM
Back Seat EDPM
Washer Stainless Steal
O-Ring EPDM
O-Ring EPDM
Gland Ductile Iron
Dust Proof Cover EPDM
Cap Ductile Iron
Stud Stainless Steel
Stud Stainless Steel
Guide Nylon
Coating Fusion Bonded Epoxy
• Non-Rising Spindle
• Fusion Bonded Epoxy Powder Coated
• EPDM Rubber Lined S.G Iron Gate
• Supplied either Socketed or Flanged
• Flange drilling to BS 4504; BSEN 1092; SANS 1123 and BS 10
• Non-Drilled Flanged Valves can be supplied on request
• Right or Left-Hand Closing
• Cap-Top or Hand Wheel operated
• Resilient Sealed to EN 1171
• Face-to-Face length according to SABS 664
• Flange Connection
• Low Torque opening and closing
Maximum Working Pressure
• 16 bar
Corrosion Protection
• Fusion bonded epoxy
Materials of Construction
Specification
32 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
DN (mm) L (mm) H (mm) D (mm) K (mm) D1 (mm) n-d (mm) b (mm) f (mm)
50 216 358 165 125 98 4-18 19 3
80 229 413 200 160 132 8-18 19 3
100 254 435 220 180 156 8-18 19 3
150 280 528 285 240 211 8-22 19 3
200 317 616 30 295 266 12-22 20 3
250 356 721 405 355 319 12-26 22 3
300 380 801 460 410 340 12-26 24.5 4
33 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
RESILIENT SEAL FLANGED GATE VALVE RISING SPINDLE
Body Ductile Iron
Bonnet Ductile Iron
Wedge Ductile Iron / EPDM Coated
Stem Stainless Steel
Gasket EPDM
Wedge Nut Stainless Steel
Bolts on bonnet flange Carbon Steel
Gland Ductile Iron
Gland bolts Stainless Steel
Yoke Nut Bronze
Handwheel Ductile Iron
Handwheel Nut Ductile Iron
Coating Fusion Bonded Epoxy
Size 50mm 80mm 100mm 125mm 150mm 200mm 250mm 300mm
L 178 203 229 254 267 292 330 356
H (Open) 385 480 550 655 740 930 1130 1320
H (Closed) 320 400 450 530 590 730 880 1020
C 184 254 254 305 305 356 445 445
• Valves comply with AWWA C515
• Superior stem graphite packing
• Packing replaceable under pressure
• Flange drilling to BS 4504; BSEN 1092; SANS 1123
and BS 10
• Cap-Top or Hand Wheel operated
• Working temperature -10° to 120°C
Maximum Working Pressure
• 16 bar
Corrosion Protection
• Fusion bonded epoxy
Materials of Construction
Specification
34 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
METAL SEATED GATE VALVE NON-RISING SPINDLE
Body Ductile Iron
Bonnet Ductile Iron
Seat Stainless Steel (Bronze available)
Wedge Ductile Iron
Wedge Trim Stainless Steel (Bronze available)
Stem Stainless Steel (Brass available)
Wedge Nut Brass
Gasket Graphite
Packing Graphite
Packing Nut Stainless Steel
Bonnet Bolts and Nuts Carbon Steel
Handwheel Ductile Iron
• Valves comply with EN1171, BS5150, BS3464 or MSS SP-70
• Metal Seat: Bronze or 304 Stainless Steel
• Adjustable Stem Seat
• Available with Handwheel, Gearbox or Actuator
• Flange drilling to BS 4504; BSEN 1092; SANS 1123 and BS 10
• Face to Face dimensions in accordance with: EN558-1 Basic
Series 3, Series 15 and ASME B16.10
Maximum Working Pressure
• 16 bar for all sizes
• 25 bar for DN 50-DN 300
Corrosion Protection
• Fusion Bonded Epoxy
Materials of Construction
Specification
35 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
Size 50
mm
65
mm
80
mm
100
mm
125
mm
150
mm
200
mm
250
mm
300
mm
350
mm
400
mm
450
mm
500
mm
600
mm
L
EN558-1 Series 3
Asme B16.10
178
191
203
229
254
267
292
330
235
381
406
432
457
508
EN558-1 Series 14 150 170 180 190 200 210 230 250 270 290 310 330 350 390
EN558-1 Series 15 250 270 280 300 325 350 400 450 500 550 600 650 700 800
BS 3464 146 159 165 171 191 210 241 273 305 - - - - -
H 265 300 344 390 461 513 616 705 800 867 966 1080 1152 1310
D 175 175 255 255 305 305 355 405 405 558 558 610 610 610
36 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SWING CHECK VALVE
Body Cast Iron
Cover Cast Iron
Side Plug Brass
Hanger Pin Stainless Steel
Hanger Ductile Iron
Disc Cast Iron
Disc Trim Bronze (EPDM/NRB available)
Body Trim Bronze
Gasket Graphite
Size DN50 DN65 DN80 DN100 DN125 DN150 DN200 DN250 DN300 DN350 DN400 DN450 DN500 DN600
L 203 216 241 292 330 356 495 622 699 787 914 914 1016 1219
H 125 137 147 166 190 217 265 300 342 402 472 500 514 605
• Designed to BS5163
• Rubber seated
• Body and bonnet ductile iron
• Carbon steel plug and bolts
• EPDM Gasket
• Flange drilling to BS 4504; BSEN 1092; SANS 1123 and BS 10
Maximum Working Pressure
• 16 Bar
Corrosion Protection
• Fusion Bonded Epoxy
Materials of Construction
Specification
37 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
Y STRAINER
Body Ductile Iron
Cover Ductile Iron
Screen Stainless Steel
Gasket Graphite
Plug Ductile Iron
Coating Fusion Bonded Epoxy
Size DN50 DN65 DN80 DN100 DN125 DN150 DN200 DN250 DN300 DN350 DN400 DN450 DN500 DN600
A 230 290 310 350 400 480 600 730 850 980 1100 1200 1250 1450
B 130 158 173 218 240 281 333 460 515 755 827 930 980 1170
Plug 1/2” 1” 1” 1” 1-1/4” 1-1/2” 1-1/2” 2” 2” 2” 2” 2” 2” 2”
• Face to Face dimensions to DIN3202-F1
• Body and bonnet ductile iron
• Carbon steel plug and bolts
• Screen is SS304
• EPDM Gasket
• Flange drilling to BS 4504; BSEN 1092; SANS 1123 and BS 10
Maximum Working Pressure
• 16 Bar
Corrosion Protection
• Fusion Bonded Epoxy
Materials of Construction
Specification
38 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SECTION K - REPAIR AND SNAP CLAMPS
REPAIR CLAMPS
Clamp Shell Stainless Steel
Studs and Nut Stainless Steel
Stud Coating Molybdinum Disulfide – Telfon Dry Film Lubricant
Bolting Mechanism Stainless Steel
Nut Cap Polypropylene Plastic
Rubber Seal EPDM (nitrile and Vton available on request)
Armour Plate Stainless Steel 304 (316 on request)
Specification
• Repair Clamps are a wide-spread range of stainless steel pipe repair
clamps which should not be used to join pipes
• The Clamps offer a permanent repair for many types of pipe
• The Clamps include various clamp lengths which range up to 1200mm
wide and are suitable for practically any pipe material
• Products from DN40 mm and greater are supplied as full
circumferential repair clamps, complete with a stainless steel armour
plate vulcanized into the rubber seal at the time of moulding
• Installation in poor site conditions is made easy with a simple flip over
action and self-retaining bolts
• An all-inclusive gasket offers a reliable seal even on corroded pipes
Materials of Construction
39 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SNAP CLAMPS
• Snap Clamps are used for repairing pin-hole breaks in small diameter pipes,
they provide a quick, easy and cost-effective solution for this type of break
Clamp Shell Stainless Steel 304 (316 available in request)
Bolt and Nut Mild Steel
Bolt and Nut Coating Hot Dip Galvanized
Lugs Ductile Iron
Lugs Coating Hot Dip Galvanized
Rubber Seal EPDM
Specification
Materials of Construction
40 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SECTION L – UNIVERSAL TAPPING SADDLE
UNIVERSAL TAPPING SADDLE
Body Ductile Iron
Gasket EPDM
Boltings Stainless Steel
Inserts Nylon/SS
Straps SS304
Coating Fusion Bonded Epoxy
Thread Outlet DN (mm) Strap Num Bolting Size
3/4" – 2”
80-150 1 M12
200-300 1 M14
350-500 1 M16
600-800 1 M16
Specification
• Universal Tapping Saddles are used to make permanent
(Hot) Tapping into existing or new water and air lines
• The saddle uses a Stainless-Steel Strap that is tightened
with fasteners on either side
• Pipe outside diameters range from 80mm – 430mm
• Body is Ductile Iron and Rubber is EPDM, SBR/NR
Maximum Working Pressure
• 16 bar
Corrosion Protection
• Fusion bonded epoxy
Materials of Construction
41 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SECTION M – REDUCING FLANGES
REDUCING FLANGES
Body Ductile Iron
Fasteners Electro Galvanized
Coating Fusion Bonded Epoxy
Size (mm) Bolt Size (mm) Bolt Number Bolt Size (mm) Bolt Number
DN40-60 M16 8
DN40-80 M16 8
DN50-60 M16 8
DN50-80 M16 8
DN50-100 M16 12
DN60-80 M16 8
DN65-80 M16 12
DN65-100 M16 12
DN80-100 M16 16
DN80-125 M16 16
DN80-150 M16 8
DN100-125 M16 16
DN100-150 M16 8 M20 8
DN100-200 M16 8 M20 16
DN125-150 M16 8 M20 8
DN150-200 M20 16
DN150-250 M20 8
DN150-300 M20 8
DN200-250 M20 20
DN200-300 M20 8
DN250-300 M20 24
Specification
• Used to connect flanges with different diameters
• Flange Drilling ISO7005-2/EN1092-2 PN10/PN16
• Ductile Iron Body with Fusion Bonded Epoxy Coating
Maximum Working Pressure
• 16 bar
Corrosion Protection
• Fusion bonded epoxy
Materials of Construction
42 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
SECTION N – RUBBER EXPANSION JOINTS
RUBBER EXPANSION JOINTS
Rubber EPDM/NBR/Neoprene
Carcass Nylon Cord Fabric
Reinforcing Wire Spring Steel Wheel
Flange Carbon Steel, Since Plated
Coating Fusion Bonded Epoxy
Size L±5 Axial Compression Axial Elongation Lateral Movement Angular Movement
DN32 95 9 6 9 15°
DN40 95 10 6 9 15° DN50 105 10 7 10 15° DN65 115 13 7 11 15° DN80 130 15 8 12 15°
DN100 135 19 10 13 15° DN125 165 19 12 13 15° DN150 180 20 12 14 15° DN200 205 25 16 22 15° DN250 240 25 16 22 15° DN300 260 25 16 22 15° DN350 265 25 16 22 15° DN400 265 25 16 22 15° DN450 265 25 16 22 15° DN500 265 25 16 22 15° DN600 265 25 16 22 15°
Specification
• Rubber: EPDM/NBR
• Carcass: Nylon Cord Fabric
• Reinforcing Wire: Spring Steel
• Flanges: Carbon Steel
• Working Pressure: 16Bar
• Flange drilling to BS 4504; BSEN 1092; SANS 1123 and BS 10
Maximum Working Pressure
• DN32-DN300: 16 bar
• DN350-DN600: 10 bar
• Fusion bonded epoxy
Materials of Construction
Corrosion Protection
43 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
` SECTION O – PVC HOSE
MINING HOSE SANS 1086-2007
Outer Layer PVC
Inner Layer PVC
Reinforcement Polyester
DESCRIPTION MAXIMUM
OPERATING
PRESSURE
BURSTING
PRESSURE
10mm PVC MINING HOSE 17 BAR 68 BAR
12.5mm PVC MINING HOSE 17 BAR 68 BAR
20mm PVC MINING HOSE 15 BAR 60 BAR
25mm PVC MINING HOSE 14 BAR 56 BAR
32mm PVC MINING HOSE 10 BAR 40 BAR
40mm PVC MINING HOSE 8.8 BAR 35 BAR
50mm PVC MINING HOSE 8.8 BAR 35 BAR
Specification
• Supplied in sizes 10mm, 12.5mm, 20mm, 25mm, 32mm,
40mm & 50mm
• SANS 1086 available in orange, blue, green (Custom colours
available on request)
• Operating pressure: 9 - 17 bar (Dependent on hose size)
• Temperature range: 0°C - 40°C
• Supplied plain-ended or as complete hose assemblies of 30m
• Applications include: Compressors, jack hammers, pneumatic
tools, high-pressure air and water conveyance
• Oil resistant and non-absorbent
Maximum Working Pressure
• Please refer to below table
Materials of Construction
MANUFACTURED IN SOUTH AFRICA
44 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
DRAGLINE HOSE SANS 271-2005
Outer Layer PVC
Inner Layer PVC
Reinforcement Polyester
Specification
• Supplied in sizes 12.5mm, 20mm, & 25mm.
• SANS 271 available in black (Custom colours available on request).
• Supplied in a minimum of 100m lengths which can be cut into
specific lengths
• Operating pressure: 9 bar.
• Temperature range: 0°C - 23°C.
• UV Resistant.
• Applications: Ideal for conveyance of water in domestic, agricultural and industrial sectors.
MANUFACTURED IN SOUTH AFRICA
Materials of Construction
45 | P a g e
TEL: +2711 952 9800
Version: KW2
www.klambon.com
PIPE OUTSIDE DIAMETER CHART
