Upload
vuongdat
View
227
Download
0
Embed Size (px)
Citation preview
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
TECHNICAL SPECIFICATION FOR TILING AND GROUTING
TREATMENT
SYSTEM RECOMMENDATION This document is the technical proposal for tiling and grouting treatments in the following option:-
Tiling works
Option 1 ......... Installation of tiles using SILVER STAR adhesive
Option 2 ......... Installation of tiles / stones using GOLD STAR adhesive
Option 3 ......... Installation of tiles / stones using WHITE STAR adhesive
Option 4 ......... Installation of tiles / stones using DIAMOND STAR adhesive
Option 5 ......... Installation of tiles / stones using PLATINUM STAR adhesive
Option 6 ......... Installation of tiles / stones using FLEX adhesive
Grouting Works
Option 1 ......... Grouting tile joints using CEMENT POLYMER GROUT
Option 2 ......... Grouting tile / stone joints using SUPER GROUT
Option 3 ......... Grouting tile / stone joints using WIDE JOINT GROUT
Option 4 ......... Grouting tile / stone joints using EPOXY GROUT
TILING WORKS
Option 1 ....................... Installation of tiles using SILVER STAR adhesive
The main features /benefits of this system are:
Polymer modified adhesive
Easy mixing and application
Good strength
Suitable for fixing ceramic tiles for wall and floors
Interior situations
Meets the adhesion requirements of BS 5980:1980 (The United Kingdom) and the
Indian Standards Is 15477 : 2004 Type 1 ”Specification for Adhesives for use with
ceramic tiles and Mosaics”
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Specification details
System proposed: Single component, grey, polymer modified, cement based adhesive
Product specified and their descriptions:
SILVER STAR : Grey, polymer modified, cement-based thin or thick bed adhesive. The properties are
as follows.
Bed thickness : 3-6mm
Walls : Use thin bed trowel
Floors : Use thick bed trowel
Pot life @27±10C : 3 Hrs
Open time @27±10C : 10-15 min
Setting time @27±10C : 24 Hrs
Temperature resistance : -300 to 1500C
Tensile adhesion for 14 days : 1.00 kN Dry Conditions
0.75 kN Wet Conditions
Shear adhesion
o 14 day air : 10 kN
o 7 day air + 7 day wet : 6.5 kN
o 7 day air + 7 day heat : 6.5kN
Under Tile Primer: Water based under tile and stone primer to prevent efflorescence
Treatment Methodology:
Scope ................................ Walls, Floors, Interior, Dry areas, wet areas and showers (Do not use
showers for at least 2 weeks after the completion of grouting).
Substrate ........................... Brick / Concrete / Sand cement rendering / brick work / Sand cement
screed / RCC
Type of Tiles ...................... Ceramic tiles / Natural stones with high porosity
Surface Preparation ........... The newly installed substrate shall be allowed to cure and dry as per
standard practice. Sharp edges and other protrusions shall be grinded to
make them flush with the surface. The surface shall be cleaned to make
it free from all dirt, dust, efflorescence, laitance and other
contaminants. Substrate shall be level (floor), flat and plumb in line
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
(wall). All tile and other non-porous surfaces shall be cleaned by
washing with water containing detergent, then with clean water.
Any loose or hollow portions shall be filled and made flush with the
surface using 1:3 cement: sand mortar applied over Slurry bond coat.
Slurry bonding coat is prepared by mixing 2 parts by weight of Portland
cement to 1 part of ADMIX AD1. Apply the mix on the substrate using
brush immediately before applying mortar.
UNDER TILE & STONE PRIMER
Application ........................ UNDER TILE & STONE PRIMER shall be applied stone including the side
edges to prevent the efflorescence as follows:-
Clean all the tile / stone to make them free from all dirt dust
and other contaminants.
Apply a coat of UNDER TILE & STONE PRIMER to under side of
the tile / stone including the side edges and leave it to soak for
5 min and wipe off any excess primer remaining on the tile /
stone.
Apply the second coat of primer at a time gap of 30 min if the
porosity of tile / stone is high.
Tile / Stone Installation ...... Installation of tiles using SILVER STAR adhesive is as follows:-
Mix the Silver star powder and clean water in ratio of (by
weight) 4:1, until a lump free smooth paste of uniform mix is
obtained, using heavy duty slow speed (less than 300 rpm)
electrical drilling machine with spiral paddle attached. Thus,
obtained mix has 3 hrs of pot life.
Spread the adhesive on floor (at 6mm thick) and wall (at 3mm
thick) using suitable steel notch trowel. (Not more than 1 Sqm
at a time)
Press the tiles firmly in to the positions with a slightly twisting
action and use suitable rubber mallet for gentle tamping.
Use spacer of required size to maintain the uniform joint
width (Joint gaps of at least of 3mm shall be provided to
facilitate movement)
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Tiles have to be fixed within 15 min and can be adjusted up to
5-10 min @27±10C. Touch the ribs of the applied adhesive
periodically, if skin has formed; replace the dry adhesive with
fresh adhesive.
Periodically make sure that the tiles are 100% adhesion with
adhesive.
After fixing the tiles, excess adhesive on faces and at joints has
to be cleaned periodically.
For height more than 20 feet, use suitable clamps to hold the
tile or stones in position.
Grouting can be carried out after 24 hrs.
Do not use in damp condition and temperature less than 5O C.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Option 2 ......................... Installation of tiles / stones using GOLD STAR adhesive
The main features /benefits of this system are:
Grey, high polymer modified adhesive
Easy mixing and smooth application and better application
For use on walls and floors in interior and exterior
High strength
Water resistance
Meets the adhesion requirements of BS 5980:1980 (The United Kingdom) and the
Indian Standards Is 15477 : 2004 Type 2 ”Specification for Adhesives for use with
ceramic tiles and Mosaics”
Specification details
System proposed: Single component, grey, high polymer modified, cement based adhesive
Product specified and their descriptions:
GOLD STAR: Single component, grey, high polymer modified, cement based adhesive. The properties
are as follows.
Bed thickness : 3-6mm
Walls : Use thin bed trowel
Floors : Use thick bed trowel
Pot life @27±10C : 3 Hrs
Open time : 15-20 min
Setting time @27±10C : 24 Hrs
Temperature resistance : -300 to 1500C
Tensile adhesion for 14 days : 1.30 kN Dry Conditions
1.0 kN Wet Conditions
Shear adhesion
o 14 day air : 12 kN
o 7 day air + 7 day wet : 7.5 kN
o 7 day air + 7 day heat : 7.5kN
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
ADMIX AD1: White, polymer emulsion for use with cement mortar/ cement based adhesives, in
interior and exterior situations in both wet and dry conditions as bonding agent / slurry coat, once
cured acts as water resistant.
UNDER TILE & STONE PRIMER: Water based under tile and stone primer to prevent efflorescence
Treatment Methodology:
Scope ................................ Walls, Floors, Interior, Exterior Dry areas, wet areas and showers (Do
not use showers for at least 2 weeks after the completion of grouting),
Swimming pools (use in conjunction with ADMIX AD 1 and do not fill
the pools for at least 3 weeks after the completion of grouting).
Substrate ........................... Brick / Concrete / Sand cement rendering / brick work / Sand cement
screed / Un-glazed tiles / Hard natural stone / Glazed tiles (use in
conjunction with ADMIX AD 1).
Type of Tiles ...................... Mosaics / Vitrified and fully vitrified tiles / Marbles / Terrazzo / Natural
stones
Surface Preparation ........... The newly installed substrate shall be allowed to cure and dry as per
standard practice. Sharp edges and other protrusions shall be grinded to
make them flush with the surface. The surface shall be cleaned to make
it free from all dirt, dust, efflorescence, laitance and other
contaminants. Substrate shall be level (floor), flat and plumb in line
(wall). All tile and other non-porous surfaces shall be cleaned by
washing with water containing detergent, then with clean water.
Any loose or hollow portions shall be filled and made flush with the
surface using 1:3 cement : sand mortar applied over Slurry bond coat.
Slurry bonding coat is prepared by mixing 2 parts by weight of Portland
cement to 1 part of ADMIX AD 1. Apply the mix on the substrate using
brush immediately before applying mortar.
UNDER TILE & STONE PRIMER
Application ........................ Under tile & stone primer shall be applied stone including the side
edges to prevent the efflorescence as follows:-
Clean all the tile / stone to make them free from all dirt dust
and other contaminants.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Apply a coat of UNDER TILE & STONE PRIMER to under side of
the tile / stone including the side edges and leave it to soak for
5 min and wipe off any excess primer remaining on the tile /
stone.
Apply the second coat of primer at a time gap of 30 min if the
porosity of tile / stone is high.
Tile / Stone Installation ...... Installation of tile / stone using Gold Star adhesive is as follows:-
Mix the Gold Star powder and clean water in ratio of (by
weight) 4:1, until a lump free smooth paste of uniform mix is
obtained, using heavy duty slow speed (less than 300 rpm)
electrical drilling machine with spiral paddle attached. Thus,
obtained mix has 3 hrs of pot life.
In case of using ADMIX AD 1, use 1 Ltr of ADMIX AD 1 for
20 Kg bag of adhesive.
Spread the adhesive on floor (at 6mm thick) and wall (at 3mm
thick) using suitable steel notch trowel. (Not more than 1 Sqm
at a time)
Press the tile / stone firmly in to the positions with a slightly
twisting action and use suitable rubber mallet for gentle
tamping.
Use spacer of required size to maintain the uniform joint
width (Joint gaps of at least of 3mm shall be provided to
facilitate movement)
Tile / stone have to be fixed within 20 min and can be adjusted
up to 15-20 min. Touch the ribs of the applied adhesive
periodically, if skin has formed; replace the dry adhesive with
fresh adhesive.
Periodically make sure that the tile / stone are 100% adhesion
with adhesive.
After fixing the tile / stone, excess adhesive on faces and at
joints has to be cleaned periodically.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
For height more than 20 feet, use suitable clamps to hold the
tile or stones in position.
Grouting can be carried out after 24 hrs.
Do not use in damp condition and temperature less than 5O C.
Suitable clamps shall be used while installing large size stone
at height more than 20 Ft for safety purpose.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Option 3 ....................... Installation of tiles / stones using WHITE STAR adhesive
The main features /benefits of this system are:
White, high polymer modified adhesive
Easy mixing and smooth application and better application
For use on walls and floors in interior and exterior
High strength
Water resistance
Meets the adhesion requirements of BS 5980:1980 (The United Kingdom) and the
Indian Standards Is 15477 : 2004 Type 2 ”Specification for Adhesives for use with
ceramic tiles and Mosaics”
Specification details
System proposed: Single component, white, high polymer modified, cement based adhesive
Product specified and their descriptions:
WHITE STAR: Single component, White, high polymer modified, cement based adhesive. The
properties are as follows.
Bed thickness : 3-6mm
Walls : Use thin bed trowel
Floors : Use thick bed trowel
Pot life @27±10C : 3 Hrs
Open time @27±10C : 15-20 min
Setting time @27±10C : 24 Hrs
Temperature resistance : -300 to 1500C
Tensile adhesion for 14 days : 1.50 kN Dry Conditions
1.1 kN Wet Conditions
Shear adhesion
o 14 day air : 14 kN
o 7 day air + 7 day wet : 8.5 kN
o 7 day air + 7 day heat : 8.5kN
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
ADMIX AD1: White, polymer emulsion for use with cement mortar/ cement based adhesives, in
interior and exterior situations in both wet and dry conditions as bonding agent / slurry coat, once
cured acts as water resistant.
UNDER TILE & STONE PRIMER: Water based under tile and stone primer to prevent efflorescence
Treatment Methodology:
Scope ................................ Walls, Floors, Interior, Exterior Dry areas, wet areas and showers (Do
not use showers for at least 2 weeks after the completion of grouting),
Swimming pools (use in conjunction with ADMIX AD 1 and do not fill
the pools for at least 3 weeks after the completion of grouting).
Substrate ........................... Brick / Concrete / Sand cement rendering / brick work / Sand cement
screed / Un-glazed tiles / Hard natural stone / Glazed tiles (use in
conjunction with ADMIX AD 1).
Type of Tiles ...................... Transparent or Semi transparent / white colour - Mosaics / Vitrified and
fully vitrified tiles / Marbles / Terrazzo / Natural stones
Surface Preparation ........... The newly installed substrate shall be allowed to cure and dry as per
standard practice. Sharp edges and other protrusions shall be grinded to
make them flush with the surface. The surface shall be cleaned to make
it free from all dirt, dust, efflorescence, laitance and other
contaminants. Substrate shall be level (floor), flat and plumb in line
(wall). All tile and other non-porous surfaces shall be cleaned by
washing with water containing detergent, then with clean water.
Any loose or hollow portions shall be filled and made flush with the
surface using 1:3 cement : sand mortar applied over Slurry bond coat.
Slurry bonding coat is prepared by mixing 2 parts by weight of Portland
cement to 1 part of ADMIX AD1. Apply the mix on the substrate using
brush immediately before applying mortar.
UNDER TILE & STONE PRIMER
Application ........................ Under tile & stone primer shall be applied stone including the side
edges to prevent the efflorescence as follows:-
Clean all the tile / stone to make them free from all dirt dust
and other contaminants.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Apply a coat of Under tile & stone primer to under side of the
tile / stone including the side edges and leave it to soak for 5
min and wipe off any excess primer remaining on the tile /
stone.
Apply the second coat of primer at a time gap of 30 min if the
porosity of tile / stone is high.
Tile / Stone Installation ...... Installation of tile / stone using White Star adhesive is as follows:-
Mix the White Star powder and clean water in ratio of (by
weight) 4:1, until a lump free smooth paste of uniform mix is
obtained, using heavy duty slow speed (less than 300 rpm)
electrical drilling machine with spiral paddle attached. Thus,
obtained mix has 3 hrs of pot life.
In case of using ADMIX AD 1, use 1 Ltr of ADMIX AD 1 for
20 Kg bag of adhesive.
Spread the adhesive on floor (at 6mm thick) and wall (at 3mm
thick) using suitable steel notch trowel. (Not more than 1 Sqm
at a time)
Press the tile / stone firmly in to the positions with a slightly
twisting action and use suitable rubber mallet for gentle
tamping.
Use spacer of required size to maintain the uniform joint
width (Joint gaps of at least of 3mm shall be provided to
facilitate movement)
Tile / stone have to be fixed within 20 min and can be adjusted
up to 15-20 min. Touch the ribs of the applied adhesive
periodically, if skin has formed; replace the dry adhesive with
fresh adhesive.
Periodically make sure that the tile / stone are 100% adhesion
with adhesive.
After fixing the tiles, excess adhesive on faces and at joints has
to be cleaned periodically.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
For height more than 20 feet, use suitable clamps to hold the
tile or stones in position.
Grouting can be carried out after 24 hrs.
Do not use in damp condition and temperature less than 5O C.
Suitable clamps shall be used while installing large size stone
at height more than 20 Ft for safety purpose.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Option 4 ....................... Installation of tiles / stones using DIAMOND STAR adhesive
The main features /benefits of this system are:
Grey – Industrial adhesive
White – Glass Mosaic adhesive
High polymer modified
High strength
Flexible tile / stone adhesive
For interior and exterior situations
Non – slip and water resistance
Meets the adhesion requirements of BS 5980:1980 (The United Kingdom) and the
Indian Standards Is 15477 : 2004 Type 2 ”Specification for Adhesives for use with
ceramic tiles and Mosaics”
Specification details
System proposed: Single component, Grey / white, high polymer modified, high strength, flexible,
cement based adhesive
Product specified and their descriptions:
DIAMOND STAR: Single component, Grey / White, high polymer modified, high strength, flexible,
cement based adhesive. The properties are as follows.
Bed thickness : 2-6mm
Walls : Use thin bed trowel
Floors : Use thick bed trowel
Pot life @27±10C : 3 Hrs
Open time : 15-20 min
Setting time @27±10C : 24 Hrs
Temperature resistance : -300 to 1500C
Tensile adhesion for 14 days : 2.00 kN Dry Conditions ( White)
1.75 kN Wet Conditions ( Grey)
Shear adhesion
o 14 day air : 18 kN (White) 16.00 kN (Grey)
o 7 day air + 7 day wet : 10 kN (White) 9.00 kN (Grey)
o 7 day air + 7 day heat : 10 kN (White) 9.00 kN (Grey)
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
ADMIX AD1: White, polymer emulsion for use with cement mortar/ cement based adhesives, in
interior and exterior situations in both wet and dry conditions as bonding agent / slurry coat, once
cured acts as water resistant.
UNDER TILE & STONE PRIMER: Water based under tile and stone primer to prevent efflorescence
Treatment Methodology:
Scope ................................ Walls, Floors, Interior, Exterior Dry areas, wet areas, limited movement
/ vibrations, showers (Do not use showers for at least 2 weeks after the
completion of grouting), Swimming pools (use in conjunction with
ADMIX AD1 and do not fill the pools for at least 3 weeks after the
completion of grouting).
Substrate ........................... Brick / Concrete / Sand cement rendering Light weight block (prime with
ADMIX AD 1, direct fixing in dry condition) / brick work / Sand cement
screed / Anhydrate screed ( direct fixing in dry condition) / Un-glazed
tiles / Hard natural stone / Glazed tiles (use in conjunction with
ADMIX AD 1).
Type of Tiles / Stones ......... Transparent or Semi transparent / white colour - Vitrified and Glass
Mosaic tiles.
Surface Preparation ........... The newly installed substrate shall be allowed to cure and dry as per
standard practice. Sharp edges and other protrusions shall be grinded to
make them flush with the surface. The surface shall be cleaned to make
it free from all dirt, dust, efflorescence, laitance and other
contaminants. Substrate shall be level (floor), flat and plumb in line
(wall). All tile and other non-porous surfaces shall be cleaned by
washing with water containing detergent, then with clean water.
Any loose or hollow portions shall be filled and made flush with the
surface using 1:3 cement : sand mortar applied over Slurry bond coat.
Slurry bonding coat is prepared by mixing 2 parts by weight of Portland
cement to 1 part of ADMIX AD 1. Apply the mix on the substrate using
brush immediately before applying mortar.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
UNDER TILE & STONE PRIMER
Application ........................ Under tile & stone primer shall be applied stone including the side
edges to prevent the efflorescence as follows:-
Clean all the tile / stone to make them free from all dirt dust
and other contaminants.
Apply a coat of UNDER TILE & STONE PRIMER to under side of
the tile / stone including the side edges and leave it to soak for
5 min and wipe off any excess primer remaining on the tile /
stone.
Apply the second coat of primer at a time gap of 30 min if the
porosity of tile / stone is high.
Tile / Stone Installation ...... Installation of tile / stone using Diamond Star adhesive is as follows:-
Mix the Diamond Star powder and clean water in ratio of (by
weight) 4:1, until a lump free smooth paste of uniform mix is
obtained, using heavy duty slow speed (less than 300 rpm)
electrical drilling machine with spiral paddle attached. Thus,
obtained mix has 3 hrs of pot life.
In case of using ADMIX AD 1, use 1 Ltr of ADMIX AD 1 for
20 Kg bag of adhesive.
Spread the adhesive on floor (at 6mm thick) and wall (at 3mm
thick) using suitable steel notch trowel. (Not more than 1 Sqm
at a time)
Press the tile / stone firmly in to the positions with a slightly
twisting action and use suitable rubber mallet for gentle
tamping.
Use spacer of required size to maintain the uniform joint
width (Joint gaps of at least of 3mm shall be provided to
facilitate movement)
Tile / stone have to be fixed within 20 min and can be adjusted
up to 15-20 min. Touch the ribs of the applied adhesive
periodically, if skin has formed; replace the dry adhesive with
fresh adhesive.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Periodically make sure that the tile / stone are 100% adhesion
with adhesive.
After fixing the tiles, excess adhesive on faces and at joints has
to be cleaned periodically.
For height more than 20 feet, use suitable clamps to hold the
tile or stones in position.
Grouting can be carried out after 24 hrs.
Do not use in damp condition and temperature less than 50 C.
Suitable clamps shall be used while installing large size stone
at height more than 20 Ft for safety purpose.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Option 5 ....................... Installation of tiles / stones using PLATINUM STAR adhesive
The main features /benefits of this system are:
Grey / White cement based adhesive
Very high polymer modified
Very high performance and strength
Premium multi use adhesive
Excellent water and frost resistance
Excellent tensile and shear adhesion
Meets the adhesion requirements of BS 5980:1980 (The United Kingdom) and the
Indian Standards Is 15477 : 2004 Type 2 ”Specification for Adhesives for use with
ceramic tiles and Mosaics” Complies with EN 12004 : 2007 C2ES1
Specification details
System proposed: Single component, Grey / white, water and frost resistant, highly polymer
modified, cement based adhesive
Product specified and their descriptions:
PLATINUM STAR: Single component, Grey / white, water and frost resistant, highly polymer
modified, cement based adhesive. The properties are as follows.
Bed thickness : 2-6mm
Walls : Use thin bed trowel
Floors : Use thick bed trowel
Pot life @27±10C : 3 Hrs
Open time @27±10C : 20-25 min
Setting time @27±10C : 24 Hrs
Temperature resistance : -300 to 1500C
Tensile adhesion for 14 days : 2.00 kN Dry Conditions
Shear adhesion
o 14 day air : >20 kN
o 7 day air + 7 day wet : >10 kN
o 7 day air + 7 day heat : >10 kN
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
ADMIX AD1: White, polymer emulsion for use with cement mortar/ cement based adhesives, in
interior and exterior situations in both wet and dry conditions as bonding agent / slurry coat, once
cured acts as water resistant.
UNDER TILE & STONE PRIMER: Water based under tile and stone primer to prevent efflorescence
Treatment Methodology:
Scope ................................ Walls, Floors, Work tops, Interior, Exterior Dry areas, wet areas,
Showers, Swimming pools, Hydrated pools, Heated screeds, limited
movement / vibrations
Substrate ........................... Concrete / Rendering / Cement sand screed / Plaster (Prime the
substrate by ADMIX AD 1) / Plaster board (Prime the substrate by
ADMIX AD 1) / Tile backer boards / Existing ceramic tiles / existing hard
natural stone / vinyl tiles / Overlaid timber floors (seal reverse and
edges using ADMIX AD1) / Plywood (seal reverse and edges using
ADMIX AD 1) / Chip board / MDF (seal reverse and edges using
ADMIX AD 1 -Internal dry areas) / Mastic Asphalt.
Type of Tiles ...................... Transparent or Semi transparent / white colour - Vitrified and Glass
Mosaic tiles.
Surface Preparation ........... The newly installed substrate shall be allowed to cure and dry as per
standard practice. Sharp edges and other protrusions shall be grinded to
make them flush with the surface. The surface shall be cleaned to make
it free from all dirt, dust, efflorescence, laitance and other
contaminants. Substrate shall be level (floor), flat and plumb in line
(wall). All tile and other non-porous surfaces shall be cleaned by
washing with water containing detergent, then with clean water.
Any loose or hollow portions shall be filled and made flush with the
surface using 1:3 cement : sand mortar applied over Slurry bond coat.
Slurry bonding coat is prepared by mixing 2 parts by weight of Portland
cement to 1 part of ADMIX AD 1. Apply the mix on the substrate using
brush immediately before applying mortar.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
UNDER TILE & STONE PRIMER
Application ........................ Under tile & stone primer shall be applied stone including the side
edges to prevent the efflorescence as follows:-
Clean all the tile / stone to make them free from all dirt dust
and other contaminants.
Apply a coat of Under tile & stone primer to under side of the
tile / stone including the side edges and leave it to soak for 5
min and wipe off any excess primer remaining on the tile /
stone.
Apply the second coat of primer at a time gap of 30 min if the
porosity of tile / stone is high.
Tile / Stone Installation ...... Installation of tile / stone using Platinum Star adhesive is as follows:-
Mix the Platinum Star powder and clean water in ratio of (by
weight) 4:1, until a lump free smooth paste of uniform mix is
obtained, using heavy duty slow speed (less than 300 rpm)
electrical drilling machine with spiral paddle attached. Thus,
obtained mix has 3 hrs of pot life.
Spread the adhesive on floor (at 6mm thick) and wall (at 3mm
thick) using suitable steel notch trowel. (Not more than 1 Sqm
at a time)
Press the tile / stone firmly in to the positions with a slightly
twisting action and use suitable rubber mallet for gentle
tamping.
Use spacer of required size to maintain the uniform joint
width (Joint gaps of at least of 3mm shall be provided to
facilitate movement)
Tile / stone have to be fixed within 20 min and can be adjusted
up to 20-25 min. Touch the ribs of the applied adhesive
periodically, if skin has formed; replace the dry adhesive with
fresh adhesive.
Periodically make sure that the tile / stone are 100% adhesion
with adhesive.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
After fixing the tiles, excess adhesive on faces and at joints has
to be cleaned periodically.
For height more than 20 feet, use suitable clamps to hold the
tile or stones in position.
Grouting can be carried out after 24 hrs.
Do not use in damp condition and temperature less than 5O C.
Suitable clamps shall be used while installing large size stone
at height more than 20 Ft for safety purpose.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Option 6 ....................... Installation of tiles / stones using FLEX adhesive
The main features /benefits of this system are:
Grey / White
Two component system, highly polymer modified adhesive
High performance flexible adhesive
Suitable for wood and metal surface
High tensile strength
Meets the adhesion requirements of BS 5980:1980 (The United Kingdom) and the
Indian Standards Is 15477 : 2004 Type 2 ”Specification for Adhesives for use with
ceramic tiles and Mosaics” Complies with EN 12004 : 2007 C2ES1
Specification details
System proposed: Grey / White – two part – rubber based powder and water based polymer liquid.
Product specified and their descriptions:
FLEX: Two part adhesive comprising of rubber based powder and water based polymer liquid which
forms water resistant and frost resistant tile adhesive. The properties are as follows.
Bed thickness : 2-3mm
Wall and floor area : Use thin bed trowel
Pot life @27±10C : 90 min
Open time : 20-25 min
Setting time @27±10C : 48 - 72 Hrs
Temperature resistance : 50O C prolonged condition,
Up to 800 C limited conditions,
Tensile adhesion for 14 days : 3.00 kN (White) 2.5 kN (Grey)
SU 10: Polyurethane based highly flexible sealant. The properties of cured sealant are as follows:-
Hardness Shore A-DIN 53 505 : 20 - 25
Modulus at 100% ISO 8339 : 0.20 - 0.25 Mpa
Elongation at Break ISO 8339 : 250%
Elastic recovery ISO 7389 : > 70%
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Water vapour Diffusion
NFT 30018 : 32g/Sqm/24 hrs
Movement Capability : 25%
UNDER TILE & STONE PRIMER: Water based under tile and stone primer to prevent efflorescence
Treatment Methodology:
Scope ................................ Walls, Floors, Interior, Exterior, Dry areas, Wet areas, Showers,
Swimming pools, Limited movement / vibrations
Substrate ........................... Substrate subjected to some limited background movement or
vibration, especially wood / plywood / metal surface (should be
screwed to frame at 300mm centers vertically and horizontally). Over
unglazed tiles, natural stones, glazed tiles, etc
Type of Tiles ...................... Transparent or Semi transparent / white colour - Vitrified and Glass
Mosaic tiles.
Surface Preparation ........... The newly installed substrate shall be allowed to cure and dry as per
standard practice. Sharp edges and other protrusions shall be grinded to
make them flush with the surface. The surface shall be cleaned to make
it free from all dirt, dust, efflorescence, laitance and other
contaminants. Substrate shall be level (floor), flat and plumb in line
(wall). All tile and other non-porous surfaces shall be cleaned by
washing with water containing detergent, then with clean water.
Any loose or hollow portions shall be filled and made flush with the
surface using 1:3 cement : sand mortar applied over Slurry bond coat.
Slurry bonding coat is prepared by mixing 2 parts by weight of Portland
cement to 1 part of ADMIX AD 1. Apply the mix on the substrate using
brush immediately before applying mortar. Joint between the board
and shall be completely sealed using SU 10 and allowed to dry
completely.
UNDER TILE & STONE PRIMER
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Application ........................ Under tile & stone primer shall be applied stone including the side
edges to prevent the efflorescence as follows:-
Clean all the tile / stone to make them free from all dirt dust
and other contaminants.
Apply a coat of UNDER TILE & STONE PRIMER to under side of
the tile / stone including the side edges and leave it to soak for
5 min and wipe off any excess primer remaining on the tile /
stone.
Apply the second coat of primer at a time gap of 30 min if the
porosity of tile / stone is high.
Tile / Stone Installation ...... Installation of tile / stone using Flex adhesive is as follows:-
Two parts of Flex adhesive ( white / grey) i.e., 5 Ltr of water-
based liquid and 2.5 Kg of rubber-based powder shall be
mixed in a suitable sized mixing vessel using slow speed heavy
duty drilling machine fixed with mixing paddle to obtain a
homogeneous mortar.
Spread the adhesive on dry wall using thin bed trowel at bed
thickness of 2-3mm (Not more than 1 Sqm at a time)
Tile / stone have to be fixed within 20 min. Touch the ribs of
the applied adhesive periodically, if skin has formed; replace
the dry adhesive with fresh adhesive.
Press the tiles firmly in to the positions with a slightly twisting
action and use suitable rubber mallet for gentle tamping.
Use spacer of required size to maintain the uniform joint
width (Joint gaps of at least of 3mm shall be provided to
facilitate movement)
Periodically make sure that the tile / stone are 100% adhesion
with adhesive.
After fixing the tiles, excess adhesive on faces and at joints has
to be cleaned periodically.
For height more than 20 feet, use suitable clamps to hold the
tile or stones in position.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Grouting can be carried out after at least 4 days.
Do not use in damp condition and temperature less than 5O C.
Suitable clamps shall be used while installing large size stone
at height more than 20 Ft for safety purpose.
GROUTING WORKS
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Option 1 ....................... Grouting tile / stone joints using CEMENT POLYMER GROUT
The main features /benefits of this system are:
Polymer modified grout
Good compression strength
Suitable for 2-6mm joints
Available in a range of colors
Specification details
System proposed: Single component, polymer modified, water resistant, cement polymer grout.
Product specified and their descriptions:
CEMENT POLYMER GROUT: Single component, polymer modified, water resistant, cement polymer
grout. The properties are as follows.
Joint width : 2-6mm
Pot life @27±10C : 30 min
Curing time @27±10C : 24 Hrs
Specific gravity : 1.7
Temperature resistance : -300C to 1500C
Compressive Strength : 4.00 KN (24 Hrs min)
8.00 KN (48 Hrs min)
ADMIX GT1: White, synthetic polymer emulsion for use with cementitious grouts, in interior and
exterior situations in both dry and wet conditions, to increase the adhesion strength, provide greater
abrasion resistance, increases flexural strength and flexibility and reduces water permeability.
Treatment Methodology:
Scope ................................ Walls, Floors, Interior, Exterior, and Dry areas
Substrate ........................... Glazed wall tiles / mosaics / Vitrified and fully vitrified tiles / floor tiles /
industrial floor tiles
Surface Preparation ........... All installed tiles area shall be allowed to cure and dry for 7 days. Joints
shall be cleaned and made free from all dirt, dust, efflorescence,
laitance and other contaminants. All tiles shall be checked for
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
soundness and good bond with the adhesive bed and substrate, if found
bad, tiles shall be removed including bed adhesive and new reinstalled
and allowed to cure and dry completely.
Joint Grouting .................... All tile joints shall be grouted using Cement Polymer Grout as follows:-
Mix the 3 part Cement Polymer Grout powder and 1 part of
clean water until a lump free smooth paste of uniform colour
is obtained, using heavy duty slow speed (less than 300 rpm)
electrical drilling machine with spiral paddle attached. Thus,
obtained mix has 30 min of pot life.
In case of using ADMIX GT 1, dilute 0.7 – 1.5 Ltr of
ADMIX GT 1 with two parts of water and mix with 10 Kg grout
powder.
Using a grout float or rubber squeeze compact the grout into
the joint ensuring that they are completely filled, remove
excess grout as much as possible from the surface of tiles.
Use sponge or sponge-board, dampened in clean water to
clean the surface of tile diagonally.
Allow about 15 min for grout to dry.
Finally, wash down with clean water with sponge / sponge
board to remove un-dried grout film from the surface.
Once the grout has sufficiently set, polish the surface with
clean cloth.
Do not apply in damp condition.
Option 2 ....................... Grouting tile / stone joints using SUPER GROUT
The main features /benefits of this system are:
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
High performance, high polymer – modified grout
Has excellent water repellent property
High strength – suitable for 2-6mm joints
Crack resistance
Non shrink
Better efflorescence resistance
Available in a range of colors
Specification details
System proposed: Single component, high quality, fine – high polymer modified high performance
grout.
Product specified and their descriptions:
SUPER GROUT: Single component, high quality fine, polymer modified, high performance with
excellent water resistance and efflorescence resistance grout. The properties are as follows.
Joint width : 2-6mm
Pot life @27±10C : 30 min
Curing time @27±10C : 24 Hrs
Specific gravity : 1.7
Temperature resistance : -300C to 1500C
Compressive Strength : 7.00 KN (24 Hrs min)
13.00 KN (48 Hrs min)
ADMIX GT 1: White, synthetic polymer emulsion for use with cementitious grouts, in interior and
exterior situations in both dry and wet conditions, to increase the adhesion strength, provide greater
abrasion resistance, increases flexural strength and flexibility and reduces water permeability.
Treatment Methodology:
Scope ................................ Walls, Floors, Interior, Exterior, and Dry areas
Substrate ........................... Glazed tiles / mosaics / vitrified and fully vitrified tiles / ceramic tiles /
industrial tiles / granites / marbles and other natural stones.
Surface Preparation ........... All installed tiles / stone area shall be allowed to cure and dry for 7 days.
Joints shall be cleaned and made free from all dirt, dust, efflorescence,
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
laitance and other contaminants. All tiles / stones shall be checked for
soundness and good bond with the adhesive bed and substrate, if found
bad, tiles / stones shall be removed including bed adhesive and new
reinstalled and allowed to cure and dry completely.
Joint Grouting .................... All tile / stones joints shall be grouted using Super grout as follows:-
Mix the 3 part SUPER GROUT powder and 1 part of clean
water until a lump free smooth paste of uniform colour is
obtained, using heavy duty slow speed (less than 300 rpm)
electrical drilling machine with spiral paddle attached. Thus,
obtained mix has 30 min of pot life.
In case of using ADMIX GT 1, dilute 0.7 – 1.5 Ltr of
ADMIX GT 1 with two parts of water and mix with 10 Kg grout
powder .
Using a grout float or rubber squeeze compact the grout into
the joint ensuring that they are completely filled, remove
excess grout as much as possible from the surface of tiles /
stones.
Use sponge or sponge-board, dampened in clean water to
clean the surface of tile diagonally.
Allow about 15 min for grout to dry.
Finally, wash down with clean water with sponge / sponge
board to remove un-dried grout film from the surface.
Once the grout has sufficiently set, polish the surface with
clean cloth.
Do not apply in damp condition.
Option 3 ....................... Grouting tile / stone joints using WIDE JOINT GROUT
The main features /benefits of this system are:
Water resistance
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Suitable for 3-12mm joint width
Suitable for floor and walls
Specification details
System proposed: Single component, high quality water resistant, polymer modified grout.
Product specified and their descriptions:
WIDE JOINT GROUT: Single component, high quality water resistant, polymer modified grout. The
properties are as follows.
Joint width : 3-12mm and up to 20mm used with ADMIX GT 1
Pot life @27±10C : 45 min
Curing time @27±10C : 24 Hrs
Specific gravity : 1.7
Temperature resistance : -300C to 1500C
Compressive Strength : 4.00 KN (24 Hrs min)
8.00 KN (48 Hrs min)
ADMIX GT1: White, synthetic polymer emulsion for use with cementitious grouts, in interior and
exterior situations in both dry and wet conditions, to increase the adhesion strength, provide greater
abrasion resistance, increases flexural strength and flexibility and reduces water permeability.
Treatment Methodology:
Scope ................................ Walls, Floors, Interior, Exterior, and Dry areas
Substrate ........................... Ceramic floor / wall tiles / mosaics / quarries, etc (Not recommended
for tiles with metal décor or luster.
Surface Preparation ........... All installed tiles area shall be allowed to cure and dry for 7 days. Joints
shall be cleaned and made free from all dirt, dust, efflorescence,
laitance and other contaminants. All tiles shall be checked for
soundness and good bond with the adhesive bed and substrate, if found
bad, tiles shall be removed including bed adhesive and new reinstalled
and allowed to cure and dry completely.
Joint Grouting .................... All tile joints shall be grouted using Wide Joint Grout as follows:-
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Mix the 5 part Cement Polymer Grout powder and 1 part of
clean water until a lump free smooth paste of uniform colour
is obtained, using heavy duty slow speed (less than 300 rpm)
electrical drilling machine with spiral paddle attached. Thus,
obtained mix has 30 min of pot life.
In case of using ADMIX GT 1, dilute 0.7 – 1.5 Ltr of
ADMIX GT 1 with two parts of water and mix with 10 Kg grout
powder.
Using a grout float or rubber squeeze compact the grout into
the joint ensuring that they are completely filled, remove
excess grout as much as possible from the surface of tiles.
Use sponge or sponge-board, dampened in clean water to
clean the surface of tile diagonally.
Allow about 15 min for grout to dry.
Finally, wash down with clean water with sponge / sponge
board to remove un-dried grout film from the surface.
Once the grout has sufficiently set, polish the surface with
clean cloth.
Do not apply at temperature less than 50C or in damp
condition.
Option 4 ....................... Grouting tile / stone joints using EPOXY GROUT
The main features /benefits of this system are:
Sterile
Can be grouted 2-20 mm wide joint.
Durable joints
Hygienic and chemical resistant
High strength
Stain and bacteria resistant
High abrasion resistant
EPOXY GROUT meets the requirement of British Standards BS 5980:1980 minimum for
resistance to mould growth. It also confirms to BS: Part 4:1992, section 9, for use in
sterile conditions. The product additionally meets the requirement of “The Material and
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Articles in Contact with Food Regulations 1987”. The Food Safety (General Food
Hygiene) Regulations 1995 and the EC Directive 93/94 in the Hygiene of food stuffs
1993.
No required water curing and available in range of colors.
Specification details
System proposed: Three components, epoxide resin-based grout
Product specified and their descriptions:
EPOXY GROUT: Three part system, epoxide resin-based grout with high degree of resistance to
chemical attack, abrasion and impact. The properties are as follows.
Joint Width : 2-20 mm
Pot life @27±10C : 45 min
Setting time @27±10C : 48 Hrs
Temperature resistance : -300C to 700C
Water absorption : Nil
Specific gravity : 1.75
Tensile adhesion : >4.50 KN (14 days dry air) Dry
Shear adhesion : >3.60 KN (14 days dry air) Wet
Treatment Methodology:
Scope ................................ Walls, Floors, Interior, Exterior, Dry areas, Wet areas, Work tops,
Showers (Do not use showers for at least 2 weeks after the completion
of grouting), Swimming pools (Do not fill pools at least 3 weeks after the
completion of grouting), Heavily trafficked floors, Hygienic sterile areas,
Chemical resistance and Hydrotherapy pools (Do not fill pools at least 3
weeks after the completion of grouting).
Substrate ........................... Tiles and stone joints
Surface Preparation ........... All installed tiles / stone area shall be allowed to cure and dry for 7 days.
Joints shall be cleaned and made free from all dirt, dust, efflorescence,
laitance and other contaminants. All tiles / stones shall be checked for
soundness and good bond with the adhesive bed and substrate, if found
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
bad, tiles / stones shall be removed including bed adhesive and new
reinstalled and allowed to cure and dry completely.
Epoxy Grout Installation ..... All joints shall be filled by using epoxy grouts as follows:-
Stir hardener and resin before adding them in to suitable
sized, clean container and thoroughly mix using heavy duty
slow speed (less than 300 rpm) drilling machine with spiral
paddle. Slowly add the required quantity of filler depending on
the joint width, required consistency, temperature, different
usage condition, etc. Mix thoroughly until all the powder is
dispersed and uniform coloured, homogeneous mix is
obtained.
Using a hard rubber / grout float compact the grout into the
joint, ensuring that they are completely filled, strike off excess
grout diagonally from the surface of tiles / stones and joints.
Plug open-ended joints with the stiffer mix to prevent any
slumping of the grout joints occurring.
Within 30 min of application, clean off surplus grout, using
emulsifying pad and gripper dampened with clean water to
break down the grout residue. Use in circular motion and keep
the pad and gripper flat relative to the tile surface to achieve a
flush joint. Do not allow water to flow / run in to the joints.
Clean off the emulsified epoxy / water residue with a sponge
in diagonally to the grout lines, taking care not to drag grout
from the joints.
ARDEX ENDURA (INDIA) PRIVATE LIMITED E-mail: [email protected], Website: www.ardexendura.com
Any light haze remaining on the tile surface can be cleaned off
using the emulsifying pad / gripper and an alkaline detergent.
Don not allow to haze remain one surface longer than 24 hrs.
The complete setting time is 48 hrs at 270C ± 10C.
Do not apply in damp condition.