Upload
others
View
0
Download
0
Embed Size (px)
Citation preview
TECHNICAL INFORMATION S2 Canister Vacuums
© 2012 Miele USA
Technical Information
2
S2 Canister Vacuums
Table of Contents
A Warning and Safety Instructions ....................................................................... 4 1 General Information .................................................................................................... 4 2 Cleaning and Care ...................................................................................................... 4
2.1 Vacuums and Accessories ............................................................................. 4 2.2 Dust Compartment ......................................................................................... 4
B Modification History ............................................................................................ 5 C Technical Data ..................................................................................................... 5 D Layout of Electrical Components ...................................................................... 7 010 Casing Bottom, Motor ....................................................................................... 10 2 Function .................................................................................................................... 11
2.1 Casters ......................................................................................................... 11 4 Service ...................................................................................................................... 11
4.1 Caster Removal ............................................................................................ 11 4.2 Motor Removal ............................................................................................. 12 4.3 Cord Reel Removal ...................................................................................... 13 4.4 Cord Removal ............................................................................................... 14
020 Casing Top ......................................................................................................... 17 2 Function .................................................................................................................... 18
2.1 Bags ............................................................................................................. 18 2.2 Bag Change Indicator ................................................................................... 18 2.2 Filters ............................................................................................................ 19
4 Service ...................................................................................................................... 19 4.1 Bag Holder Removal .................................................................................... 19 4.2 Bag Change Indicator Removal .................................................................... 19 4.3 Casing Top Removal .................................................................................... 20 4.4 Motor Protection Filter Frame Removal ........................................................ 21 4.5 Cover Frame Removal ................................................................................. 21 4.6 Air Inlet Regulator Removal .......................................................................... 23 4.7 Changing the Bag ......................................................................................... 23 4.8 Replacing the Super Air Clean Filter ............................................................ 24 4.9 Replacing the Active Air Clean or Active HEPA Filter ................................... 24 4.10 Replacing One Type of Filter with Another ................................................... 25 4.11 Changing the Dust Compartment (Motor Protection) Filter ........................... 25
030 Controls, Electronic .......................................................................................... 26 2 Function .................................................................................................................... 27
2.1 Suction Power .............................................................................................. 27 3 Fault Repair .............................................................................................................. 27
3.1 Vacuum Cleaner Cannot Be Switched On .................................................... 27 3.2 Vacuum Cleaner Shuts Itself Off or Overheating Indicator LED Lights Up ... 28
4 Service ...................................................................................................................... 28 4.1 Cap Removal ................................................................................................ 28 4.2 Electronic Removal ....................................................................................... 30 4.3 On/Off Switch Removal ................................................................................ 30
040 Suction Hose, Accessories .............................................................................. 31 2 Function .................................................................................................................... 32
Technical Information
3
S2 Canister Vacuums
2.1 Accessories .................................................................................................. 32 3 Fault Repair .............................................................................................................. 32
3.1 Suction Power Too Low ................................................................................ 32 4 Service ...................................................................................................................... 33
4.1 Telescopic Suction Hose Locking Piece Replacement ................................. 33 4.2 Pushbutton Replacement (for Telescopic Hoses) ......................................... 34
List of Figures Figure D-1: Control Panel (at Rear of Vacuum) ...................................................................... 7 Figure D-2: Internal Component Layout .................................................................................. 7 Figure D-3: External Component Layout (with Basic Suction Hose) ....................................... 8 Figure D-4: External Component Layout (with Electro Accessories) ....................................... 9 Figure 010-1: Support Roller and Axle .................................................................................. 11 Figure 010-2: Caster Removal .............................................................................................. 12 Figure 010-3: Electronic Retainer.......................................................................................... 12 Figure 010-4: Motor ............................................................................................................... 13 Figure 010-5: Cord Reel and Motor....................................................................................... 13 Figure 010-6: Cord Reel Retainer on Side ............................................................................ 14 Figure 010-7: Cord Reel, Unwound ....................................................................................... 14 Figure 010-8: Cord Reel Clamped to Reel Assembly Body .................................................. 15 Figure 010-9: Screws Securing Cord Reel ............................................................................ 15 Figure 010-10: Cord Reel Tabs ............................................................................................. 16 Figure 020-1: Bag Change Indicator ..................................................................................... 18 Figure 020-2: Filter Types ..................................................................................................... 19 Figure 020-3: Bag and Holder ............................................................................................... 19 Figure 020-4: Bag Change Indicator Removal ...................................................................... 20 Figure 020-5: Casing Top Removal ...................................................................................... 20 Figure 020-6: Filter Frame Retaining Tabs ........................................................................... 21 Figure 020-7: Cover Frame Screws ...................................................................................... 22 Figure 020-8: Cover Frame Removal .................................................................................... 22 Figure 020-9: Air Inlet Regulator ........................................................................................... 23 Figure 020-10: Changing the Bag ......................................................................................... 24 Figure 020-11: Replacing the Super Air Clean Filter ............................................................. 24 Figure 020-12: Replacing the Active Air Clean or Active HEPA Filter ................................... 25 Figure 020-13: Changing the Dust Compartment Filter ......................................................... 25 Figure 030-1: Rotary Selector Switch .................................................................................... 27 Figure 030-2: Cap Screws .................................................................................................... 29 Figure 030-3: Notches ........................................................................................................... 29 Figure 030-4: Tabs ................................................................................................................ 30 Figure 040-1: Accessories .................................................................................................... 32 Figure 040-2: Telescopic Locking Piece ............................................................................... 33 Figure 040-3: Pushbutton Replacement ................................................................................ 34 List of Tables Table C-1: S2 Data Sheet, US Models .................................................................................... 6
Technical Information
4
S2 Canister Vacuums
A Warning and Safety Instructions
1 General Information
All repairs should be performed by a trained technician in strict accordance with national, state and local codes. Any repairs or maintenance performed by unqualified personnel could be dangerous.
When servicing, modifying, testing or maintaining appliances, all applicord
laws, regulations and accident prevention guidelines must be observed.
All regulations of the appropriate utility supply companies and standards relating to safety (not limited to electrical safety) are to be complied with.
Before any service work is started, the vacuum cleaner must be
disconnected from the power supply. Even with the vacuum switched off, voltage may be applied to some components.
Do not leave the vacuum unattended when it is plugged in. Turn off and
unplug the vacuum before opening the cover.
After work has been completed, a visual as well as an operational check should always be performed.
2 Cleaning and Care 2.1 Vacuums and Accessories
The vacuum cleaner and other plastic components can be cleaned using a damp cloth or a cleaner made especially for plastics.
Warning! Do not use abrasive, glass or all-purpose cleaning solutions, as these can cause considerable damage to the plastic components of the vacuum or its accessories.
2.2 Dust Compartment The dust compartment can be cleaned using another vacuum, if available, or a dry cloth or brush.
Monitor the bag change indicator and inspect all filters regularly. Replace them when necessary according to the operating instructions.
Technical Information
5
S2 Canister Vacuums
B Modification History
When? Who? What? 7/18/2012 Jessica Naples S 2121 (HomeCare) model info added
8/10/2011 Jessica Naples Cord reel troubleshooting and cord removal added
11/20/2009 Jessica Naples Conversion for Website 6/17/2008 Armin Mannert Initial compilation
C Technical Data
Model S 2110 S 2120 S 2121 S 2130 S 2180 Weight, without accessories 13.2 lbs (6kg)
Radius of operation
30' (9m)
Bag capacity 1.2 gal (4.5L)
Noise insulation Yes
Motor gentle start Yes
Suction power adjustment Rotary switch
On/off switch for Park System No
Bag type G/N
Super Air Clean filter Yes No
Active Air Clean filter No
Active HEPA filter No Optional No Yes
Bag change indicator Yes
Electric exhaust filter change indicator No
Overheating indicator light No
Blower function No
Filter grille Yes
Automatic cord rewind Yes
Technical Information
6
S2 Canister Vacuums
Model S 2110 S 2120 S 2121 S 2130 S 2180 Accessories supplied
2 single connectable suction hoses (Easylock)
Model-dependent
2-part stainless-steel suction hose Model-dependent
3-part stainless-steel telescopic suction hose (TriScope)
Model-dependent
Electro-telescopic suction hose No Yes No
Suction hose holder Integrated
Suction hose connection Cylindrical stub
Universal floor attachment
SBD 350-3 SBD 470-3 SBD 450-3 SBD 350-3
Electrobrush/ Rechargeable electrobrush
Optional accessory SEB 228 Optional accessory
Turbo brush Optional accessory
Upholstery nozzle/ Dusting brush Yes/Yes
Crevice nozzle/ Extended crevice nozzle
Yes/No
Electrical connection - USA models only
Power rating 1200W
Voltage 120V
Fuse rating 15A
Power consumption 0.3 - 1.4 kWh Table C-1: S2 Data Sheet, US Models
Technical Information
7
S2 Canister Vacuums
D Layout of Electrical Components
Figure D-1: Control Panel (at Rear of Vacuum)
Figure D-2: Internal Component Layout
1 Cord reel W16 2 Electronic 3 Main switch Q1 4 Motor
Technical Information
8
S2 Canister Vacuums
Figure D-3: External Component Layout (with Basic Suction Hose)
1 Handle 13 Bag 2 Air inlet valve 14 Motor protection filter 3 Release button 15 Exhaust filter (model-dependent) 4 Easylock suction hose 16 On/off footswitch 5 Adjustment knob for telescopic
suction hose(model-dependent) 17 Park System
6 Connection receptacle 18 Power cord 7 Suction hose (model-dependent) 19 Footswitch for automatic cord rewind 8 Telescopic suction hose
(model-dependent) 20 Bag change indicator
9 Release button for dust compartment cover
21 Accessory holder for 3 accessories
10 Suction power regulator 22 Suction hose 11 Floor attachment Not shown Suction hose holder (on underside of
appliance) 12 Carrying handle
Technical Information
9
S2 Canister Vacuums
Figure D-4: External Component Layout (with Electro Accessories)
1 Handle 12 Socket for electro accessories 2 On/off switch for electrobrush 13 Bag 3 Lock release button 14 Motor protection filter 4 Electro-telescopic wand 15 Exhaust filter (model-dependent) 5 Elbow 16 On/off footswitch 6 Plug for electro accessories 17 Park System 7 Electro telescopic wand release button 18 Power cord 8 Release button for dust compartment cover 19 Footswitch for automatic cord rewind 9 Suction power regulator 20 Bag change indicator
10 Electrobrush 21 Accessory holder for 3 accessories 11 Carrying handle 22 Suction hose SES 116
Technical Information
10
S2 Canister Vacuums
010 Casing Bottom, Motor
Technical Information
11
S2 Canister Vacuums
2 Function 2.1 Casters
The appliance has three casters that can rotate through 360°. The caster rollers are mounted on steel axles. The roller contact surfaces are covered with a soft plastic coating.
4 Service 4.1 Caster Removal
1. Lever out the support roller and axle with a flathead screwdriver. See Figure 010-1.
Figure 010-1: Support Roller and Axle
2. Lever out the caster; see Figure 010-2.
Technical Information
12
S2 Canister Vacuums
Figure 010-2: Caster Removal
4.2 Motor Removal 1. Remove the casing top. See Section 020-4.3. 2. Remove the cap. See Section 030-4.1. 3. Release the electronic retainer, Figure 010-3, Item 1, and tilt it upwards,
Figure 010-3, Item 2.
Figure 010-3: Electronic Retainer
4. Remove the cover frame; see Section 020-4.5. 5. Lift the motor (Figure 010-4, Item 1) up and out of the appliance. 6. Disconnect the connection to the cord reel.
Technical Information
13
S2 Canister Vacuums
Figure 010-4: Motor
Note: When re-installing, the rubber seal must first be installed in the cover frame.
4.3 Cord Reel Removal 1. Remove the casing top. See Section 020-4.3. 2. Remove the cap. See Section 030-4.1. 3. Release the electronic retainer, Figure 010-3, Item 1, and tilt it upwards,
Figure 010-3, Item 2. 4. Remove the cover frame; see Section 020-4.5. 5. Disconnect the cord reel (Figure 010-5, Item 1) from the motor (Figure
010-5, Item 2).
Figure 010-5: Cord Reel and Motor
6. Free the cord reel assembly from its retainers (Figure 010-5, Item 3, and Figure 010-6, Item 1).
Technical Information
14
S2 Canister Vacuums
Figure 010-6: Cord Reel Retainer on Side
7. Disconnect the cord reel from the electronic. 8. Release all wires from their guides. 9. Remove the electronic retainer.
4.4 Cord Removal Note: Use only a genuine Miele cord for the correct vacuum model number.
Note: Never replace the cord end.
1. Remove the cord reel. See Section 010-4.3. 2. Unwind the cord completely. See Figure 010-7.
Figure 010-7: Cord Reel, Unwound
Technical Information
15
S2 Canister Vacuums
3. Clamp the cord reel to the body of the cord reel assembly to immobilize it. See Figure 010-8. Failure to clamp the cord reel can allow it to rotate, changing the spring tension and affecting operation. The reel can also separate from the body, releasing the tension spring. Always clamp the reel to the body before performing any cord repair.
Figure 010-8: Cord Reel Clamped to Reel Assembly Body
4. Once the clamp is in place, remove the 2 T10 screws from the cord reel. See Figure 010-9.
Figure 010-9: Screws Securing Cord Reel
5. Release the tabs holding the two halves of the cord reel together. See Figure 010-10. The top of the reel will lift straight up.
Technical Information
16
S2 Canister Vacuums
Figure 010-10: Cord Reel Tabs
6. Remove the cord from the cord reel. 7. Install the new cord. 8. Reassemble the reel halves. Do not remove the clamp until the cord reel
halves are fully assembled. 9. When the reel has been reassembled, remove the clamp and retract the
cord slowly, leaving a 6” tail. Once the cord reel is installed in the vacuum it is important to do an operational check and ensure that the cord extends and retracts correctly.
Technical Information
17
S2 Canister Vacuums
020 Casing Top
Technical Information
18
S2 Canister Vacuums
2 Function 2.1 Bags
A clean bag is essential to the maximum efficiency of the vacuum. A clogged bag can cause restricted airflow resulting in poor suction or, in extreme cases, an overheat condition can occur resulting in the vacuum shutting off. Changing the bag is relatively easy; the most important thing to remember is to use the correct bag. A list of bags and the models in which they are used can be found in the product line information in the operating manual.
2.2 Bag Change Indicator
Figure 020-1: Bag Change Indicator
To test the bag change indicator:
1. Connect the floor attachment to the suction hose. 2. Switch on the vacuum cleaner. 3. Set the selector to full power. 4. Lift the floor attachment from the floor. If the window in the bag change
indicator is completely red, then the bag must be changed. See Section 020-4.7 for instructions.
The display function is set for mixed dust (dust, hairs, threads, carpet fluff, sand, etc.).
If large quantities of fine dust (e.g., from drilling holes in masonry, fine sand, etc.) are vacuumed, the bag pores are quickly blocked. The bag change indicator then indicates “full” even though it is not actually full. However, the bag should still be replaced.
If large quantities of hair, carpet fluff, etc., are vacuumed, the indicator might not react until the bag is stuffed full.
Technical Information
19
S2 Canister Vacuums
2.2 Filters Miele canister vacuums use several types of filters (Super Air Clean, Active Air Clean, Active HEPA) to provide a clean, healthy environment. See Figure 020-2. Vacuum model will dictate filter(s) type. See Table C-1.
Figure 020-2: Filter Types
Note: Changing from one type of filter to another type is permitted. (e.g., Active Air Clean to Active HEPA). See Section 020-4.10 for instructions.
4 Service
4.1 Bag Holder Removal 1. Open the casing top wide. 2. Remove the bag (Figure 020-3, Item 1). 3. Press the holder (Figure 020-3, Item 2) downwards on one side. 4. Remove the holder from its guide.
Figure 020-3: Bag and Holder
4.2 Bag Change Indicator Removal 1. Open the casing top. 2. Lever the bag change indicator from its guide using a small flathead
screwdriver; see Figure 020-4.
a Super Air Clean b Active Air Clean c Active HEPA (High Efficiency Particulate Air)
Technical Information
20
S2 Canister Vacuums
Figure 020-4: Bag Change Indicator Removal
4.3 Casing Top Removal 1. Open the casing top wide. 2. Lever out the hinge arms, Figure 020-5.
Figure 020-5: Casing Top Removal
Technical Information
21
S2 Canister Vacuums
4.4 Motor Protection Filter Frame Removal 1. Open the casing top wide. 2. Remove the bag. 3. Release the frame retaining tabs with a suitable tool; see Figure 020-6,
Item 1. 4. Remove the frame.
Note: If it is too difficult to release the tabs from the top, open the frame, insert the flathead screwdriver behind it and pry it out.
Figure 020-6: Filter Frame Retaining Tabs
Note: When re-installing, insert the top of the frame first.
4.5 Cover Frame Removal 1. Remove the casing top. See Section 020-4.3. 2. Remove the exhaust filter. 3. Remove the cap. See Section 030-4.1. 4. Release the electronic retainer, Figure 010-3, Item 1, and tilt it upwards,
Figure 010-3, Item 2. 5. Remove the bag holder; see Section 020-4.1. 6. Remove the six cover frame retaining screws (T20); see Figure 020-7,
Item 1.
Technical Information
22
S2 Canister Vacuums
Figure 020-7: Cover Frame Screws
7. Hold the base firmly with one hand by pressing down at Figure 020-8, Item 2. Grasp inside the cover frame at Figure 020-8, Item 3, and pull straight up, about ¼ to ½ inch, until the handle locking tabs disengage (audible click).
8. Release the cord reel retainer, Figure 020-8, Item 1, and then remove the cover frame.
Figure 020-8: Cover Frame Removal
Note: When re-installing, install the front and rear screws first, then the side screws.
Technical Information
23
S2 Canister Vacuums
4.6 Air Inlet Regulator Removal 1. Remove the casing top. See Section 020-4.3. 2. Remove the cap. See Section 030-4.1. 3. Remove the cover frame. See Section 020-4.5. 4. Turn the cover frame over. 5. Remove the air inlet regulator; see Figure 020-9, Item 1.
Figure 020-9: Air Inlet Regulator
4.7 Changing the Bag
1. Open the lid. 2. Pull the bag out by the grip next to the self-closing flap on the collar
(Figure 020-10, Item 1). 3. Discard the full bag in a suitable container (trash can). 4. Remove the NEW bag from the box. DO NOT UNFOLD IT. 5. Slide the new bag into the holder as far as it will go (Figure 020-10, Item 2). 6. Close the lid, making sure that it clicks into place.
Note: The lid will not close without a bag in place, or if the bag is inserted incorrectly. Do not force it.
Technical Information
24
S2 Canister Vacuums
Figure 020-10: Changing the Bag
4.8 Replacing the Super Air Clean Filter 1. Open the dust compartment lid. 2. Unclip the filter grill and raise it up. 3. Carefully grasp the used filter at a clean, UNSOILED section (see arrow)
and remove (Figure 020-11, Item 1). 4. Replace with a new filter. It can be inserted either side up. 5. Close the filter grill and and snap it back into place. 6. Close the dust compartment lid.
Figure 020-11: Replacing the Super Air Clean Filter
4.9 Replacing the Active Air Clean or Active HEPA Filter 1. Open the dust compartment lid. 2. Lift out the old exhaust filter (Figure 020-12, Item 1). 3. Replace it with the new filter (Figure 020-12, Item 2). 4. Close the dust compartment lid.
Technical Information
25
S2 Canister Vacuums
Figure 020-12: Replacing the Active Air Clean or Active HEPA Filter
4.10 Replacing One Type of Filter with Another
If you wish to replace the SUPER AIR CLEAN FILTER with the ACTIVE AIR CLEAN FILTER or the ACTIVE HEPA FILTER, you MUST REMOVE the grill BEFORE inserting the new type of filter.
If you wish to replace the ACTIVE AIR CLEAN FILTER or the ACTIVE HEPA FILTER with the SUPER CLEAN FILTER then you MUST ALSO INSERT the grill.
The ACTIVE AIR CLEAN FILTER can be used instead of the ACTIVE HEPA FILTER, or vice versa, without any changes.
4.11 Changing the Dust Compartment (Motor Protection) Filter
Replace the dust compartment filter every time a new box of bags is started.
1. Open the dust compartment lid. 2. Unclip the filter frame, remove the old filter (Figure 020-13, Item 1) and
replace it with a new one (Figure 020-13, Item 2). 3. Close the filter frame. 4. Close the dust compartment lid.
Figure 020-13: Changing the Dust Compartment Filter
Technical Information
26
S2 Canister Vacuums
030 Controls, Electronic
Technical Information
27
S2 Canister Vacuums
2 Function 2.1 Suction Power
Figure 030-1: Rotary Selector Switch
The suction power is set via the rotary selector switch as appropriate for the surface to be vacuumed:
: Curtains and textiles : Upholstery, cushions : High-quality carpets, rugs and runners
: Energy saving, everyday vacuuming with reduced noise level : Lightly soiled carpets and soft floors : Hard floors, heavily soiled carpets and soft floors
For more information, see the general DTD.
3 Fault Repair
3.1 Vacuum Cleaner Cannot Be Switched On Cause: On/off switch faulty. Remedy: 1. Remove the electronic; see Section 030-4.2. 2. Check the switch contacts for continuity. 3. If continuity does not exist, replace the on/off switch. See On/Off Switch
Replacement, Section 030-4.3.
Cause: 1. Faulty cord reel. 2. Faulty cord. Remedy: 1. Remove the cord reel; see Section 010-4.3. 2. Check for voltage on the back of the cord reel (between terminals L and
Technical Information
28
S2 Canister Vacuums
N). Voltage reading should be 120VAC +/- 10 volts. 3. If cord reel voltage is faulty (or nonexistent), then the cord reel is
defective. Replace it with a new one, following the instructions in Section 010-4.3.
4. If cord reel voltage is correct, then check voltage at the cord. Measure between the black and white wires on the front of the cord reel (visible through the “window”). Voltage reading should be 120VAC +/- 10 volts.
5. If cord voltage is faulty (or nonexistent), then the cord is defective. Replace it with a new one, following the instructions in Section 010-4.4.
3.2 Vacuum Cleaner Shuts Itself Off or Overheating Indicator LED
Lights Up Cause: The motor has overheated and the thermostat has tripped. Remedy: 1. Switch off the appliance. 2. Disconnect the power cord. 3. Identify the cause of overheating and rectify it.
Note: Possible fault causes:
Bag is full or fine dust has made it non-porous. Motor protection or exhaust filter severely soiled. Suction hose blocked.
Possible remedies: Change bag. Change motor protection or exhaust filter. Clear any obstructions in the suction hose.
After the problem has been rectified, the vacuum cleaner must be allowed to cool for approximately 30 minutes. It can then be used again.
4 Service 4.1 Cap Removal
1. Remove the casing top; see Section 020-4.3. 2. Remove the exhaust filter. 3. Turn the rotary switch counterclockwise as far as possible. 4. Remove the two retaining screws (T20); see Figure 030-2, Item 1.
Technical Information
29
S2 Canister Vacuums
Figure 030-2: Cap Screws
5. Press a suitable tool into the recess under the left and right footswitches next to the Park System (Figure 030-3, Item 1). Pull up at Figure 030-3, Item 2, to release the retaining tabs (Figure 030-4, Item 1).
6. Remove the cap upwards.
Figure 030-3: Notches
Technical Information
30
S2 Canister Vacuums
Figure 030-4: Tabs
4.2 Electronic Removal 1. Remove the casing top. See Section 020-4.3. 2. Remove the cap. See Section 030-4.1. 3. Release the electronic retainer, Figure 010-3, Item 1, and tilt it upwards,
Figure 010-3, Item 2. 4. Remove the cover frame; see Section 020-4.5. 5. Remove the cord reel. See Section 010-4.3. 6. Disconnect all connections from the electronic. 7. Remove the electronic from its retainer.
4.3 On/Off Switch Removal 1. Remove the casing top. See Section 020-4.3. 2. Remove the cap. See Section 030-4.1. 3. Release the electronic retainer, Figure 010-3, Item 1, and tilt it upwards,
Figure 010-3, Item 2. 4. Remove the on/off switch from its holder using a suitable tool. 5. Disconnect the plug connections.
Technical Information
31
S2 Canister Vacuums
040 Suction Hose, Accessories
Technical Information
32
S2 Canister Vacuums
2 Function 2.1 Accessories
Figure 040-1: Accessories
The accessory holder can either be clipped in position on the connection stub or the handle connection sleeve.
For more information, see the operating instructions or the general DTD.
3 Fault Repair 3.1 Suction Power Too Low
Cause: Floor attachment or suction hose blocked. Remedy: Clean the floor attachment or suction hose.
Cause: Bag full. Remedy: Change the bag.
Note: If the window in the bag change indicator is completely red, then the bag must be changed.
Cause: Motor protection filter clogged. Remedy: Replace the motor protection filter.
1 Dusting brush 2 Upholstery brush 3 Crevice nozzle 4 Accessory holder
Technical Information
33
S2 Canister Vacuums
Note: The motor protection filter should always be changed when a new pack of Miele vacuum bags is opened. A motor protection filter is supplied with every pack of Miele vacuum bags.
Cause: Exhaust filter clogged. Remedy: Replace the exhaust filter.
Note: 1. Super Air Clean This exhaust filter should always be changed when a new pack of Miele vacuum bags is opened. A Super Air Clean exhaust filter is supplied with every pack of Miele vacuum bags. 2. Active Air Clean - Active HEPA This exhaust filter must be changed after approximately 1 year. The date can be written on the filter.
4 Service
4.1 Telescopic Suction Hose Locking Piece Replacement 1. Release the old locking piece with a small flathead screwdriver. 2. Remove the cap (Figure 040-2, Item A). The pushbutton and spring
underneath will be released as well. 3. The insert (Figure 040-2, Item B) will also come out when the locking
piece is removed.
Figure 040-2: Telescopic Locking Piece
Note: When re-installing, carry out the following in the given order: 1. Install the pushbutton, Figure 040-2, Item A. 2. Press and hold the pushbutton while sliding the insert (Figure 040-2, Item
B) into the suction hose.
The insert can be replaced separately, if needed.
Technical Information
34
S2 Canister Vacuums
4.2 Pushbutton Replacement (for Telescopic Hoses) 1. Pry off the old pushbutton with a small flathead screwdriver. 2. Place the bar, Figure 040-3, Item D, in its holder. 3. Place the spring, Figure 040-3, Item A, in its holder. 4. Place the pushbutton, Figure 040-3, Item B, on the bar. 5. Push the housing, Figure 040-3, Item C, into position. 6. Check for correct function.
Figure 040-3: Pushbutton Replacement