Table of ContentsProduct Layout...................................................................................................................................2Technical Specifications..................................................................................................................2General Safety Precautions...........................................................................................................2

Additional Safe Work Tips........................................................................................................3Assembly...............................................................................................................................................4Grinding Disk Maintenance............................................................................................................5

Grinding Disk Assembly.............................................................................................................5Clamping Screw Setup...............................................................................................................6

Grinding.................................................................................................................................................6Grinding Depth Gauge................................................................................................................7

Dimensions............................................................................................................................................7Parts List................................................................................................................................................8

1

Product Layout1. Handle

2. Grinding Disk Lateral Guard

3. Depth of Grind Set Screw

4. Cutting Edge Angle Wheel

5. Base

6. Screw Clamp Cradle

7. Cutting Angle Wheel

8. Scale

9. Clamping Lever

10. Mean Distance Set Screw

11. Guide Flap Valve

12. Screw Clamp

13. Guide Position Set Screw

14. Setting Screw

15. Grinding Disk

16. Grinding Disk Protective Enclosure

Technical Specifications

Supply Voltage: 230V / 50Hz

Motor Input Speed: 230W

Maximum Speed: 3000rpm

Protection : IP20

Noise Level: LWA 85dB (A)

Weight: Approx 4.5kg

General Safety PrecautionsRead the instruction manual carefully before the first use of the machine. If you have any doubt regarding the connection and operation of the unit, contact the Kogan.com customer support team.

Protect the unit from moisture, rain and dust!

• To ensure the highest degree of safety, please follow these instructions:• Use the unit only for the scope of work for which it has been designed.• When using the chainsaw sharpener outdoors, you should always use a weather resistant extension

cable to connect it, with a minimum diameter of 1.5mm2 with a splash-proof plug and socket.• The noise level in the working area will be above 85dB(A), so ear protection must be worn!• For your own safety, always use a dust mask and safety goggles.• Always unplug the unit before performing any work on it (cleaning, grinding disk replacement

etc...)• Take care to have the saw-chain secured properly to stop it from slipping out.• Please ensure that you clean dust and debris from the grinder after every use. You should also

check the unit for any damage.

2

• Do not use any caustic substances to clean the sharpener.• Do not use the unit or work on it within the proximity of flammable liquids or vapours.• Protect the power cable from any damage, including acids or oils.• Observe any and all national safety regulations regarding the installation, operation and

maintenance of this product.• Upon completion of your sharpening jobs, unplug the chainsaw sharpener from the mains power.• Working gloves will protect your fingers and skin from cutting injuries during use. Be sure to keep

your hands away from the grinding disk when it is moving.• Store the unit in a location that is inaccessible to children.• Always hold the unit with both hands when working, and be sure you are standing with secure

footing on a stable surface.

Additional Safe Work Tips• Keep your workplace tidy.

A messy workplace may cause an accident.• Always make allowances for environmental effects and factors.

Do not expose the unit to rain, or use in a wet or moist location. Ensure there is sufficient lighting and there are no flammable liquids or gases in the area.

• Prevent children from access.Do not let other people touch the unit or the power cable. Prevent unauthorised people from gaining access to the working area.

• Store the unit in a safe location.When not in use, the unit should be kept in a dry, elevated locked location, out of reach of children.

• Use the correct machine. Do not use the unit for any purpose other than what it is intended for. Only use the unit as described in the user manual.

• Wear proper clothing!Do not wear any wide or loose garments or jewellery that may get caught in moving parts. For working outdoors, rubber gloves and non-skid shoes are recommended. If you hair is long, tie it up or wear a hairnet. Use protective goggles.

• Wear a breathing mask when engaged in a dust-producing job.• Do not use the cable for any purpose other than what it is intended for.

Do not use the cable for carrying or hanging the machine. Do not use the cable itself to pull the plug out of the socket. Protect the cable from excessive temperatures, oil or sharp edges.

• Avoid any abnormal posture. Mind your safe footing and balance at all times.

• Take due care of the unit.Abide by the maintenance and grinding disk replacement regulations.Check the power cable regularly and when it is found to be damaged, have it replaced by an electrician. Check extension cables regularly and replace them if damaged.Keep the handle dry, free of dirt, oil and grease.

• Unplug the machine when not in use, prior to maintenance or when replacing a grinding disk.• Remove any spanners from the unit.

Before switching on, check to see that any wrenches or adjustment tools have been removed.• Be attentive and mind what you are doing.

Never use the machine while you are distracted, after consuming alcohol or taking medication, or under any other circumstances that may impact your ability to concentrate.

• Check the machine prior to use for any possible damage.• Before using the unit, you should check any protective devices and any parts showing any slight

damage to see that the function intended is still available. Check to see that moving parts are moving freely, do not drag and are not damaged. Any parts should be installed properly to comply with the conditions of the machines safe operation. Parts should only be repaired in a professional workshop. Do not use the unit with a defective ON/OFF switch.

3

AssemblyThe chainsaw sharpener is delivered partially assembled. One part consists of the base, on whichthe chain guide is located. The other part is the bearing arm with the motor and hand-grip.

The assembly MUST be performed with the machine unplugged!

• The unit design allows either for a desk installation or a wall mounting. When installing it on a desk, push the unit up against the edge of the desk to the stop (see Fig. 1), then screw it to the desk using the holes in the base.

• When mounting the unit onto a wall, use the respective holes in the vertical part of the base (here, a distance from the wall should be kept, or spacers should be used so that access to the rear set screws is maintained).

• After the desk top installation, fit the arm in the base by inserting the pilot pin and securing it with a hexagonal screw (see Fig. 2).

• Now, it is possible to fit a washer on the rear side screw and screw the setting wheel on (see Fig. 3).

• Screw the supporting arm control holder on the screw in the grinding disk body.• Fit the grinding disk enclosure on using the supplied screws and suitable wrench (See

Fig. 4).

TIP: When mounting unit on the wall, take care to mount the unit at the approximate height of 120 ~ 130cm from the floor to avoid working at eye height. Be sure to keep children away whenusing this unit.

To install the grinding disks, it is necessary to unscrew the auxiliary flange (see Fig. 5).

4

Grinding Disk MaintenanceTo avoid injuries and accidents, only grinding disks free of defects should be used.

Check the disk you are about to fit for any damages prior to assembly.

This can be done by a simple sound test: Hold the disk so that a pencil canbe put into the hole of the disk and the disk can swing freely (see image).

• Now tap the edge of the disk with another pencil carefully.The disk should make a clear, high pitched sound!

• If the sound is dull, then the disk is defective and should not be used.A dull sound indicates damage by cracks.

• Do not fit the disk onto the hub by force.• The central bore diameter should never be changed.• Use only disks supplied by Kogan.com.• The grinding disks should not be used if they have a diameter

smaller than 100mm. Disks that have been grinded below thisdiameter should be replaced.

• Any adjusting works to the disk should not be done unless the unit is switched off AND unplugged from the power supply.

Grinding Disk Assembly

After you have removed the ancillary flange, you can insert the grinding disk into the bodyfrom below. See that the ancillary flange and the disk are against each other (see Fig. 7).

Do not over-tighten the screws, as this can damage thedisk.

The grinding disk on the hug torque is 7Nm. Where practical, use a torque spanner. Now the lateral guard can be fitted (see Fig. 8).

Check for the correct installation of the disk: there should be no wobbling. To check, a trial run should be performed. Stand next to the machine and ensure that there is nobody else in the working area.

If the grinding disk is wobbling or shows otherwise incorrect movement, promptly switch the unit off and unplug it from the power supply before working on the grinding disk.

The unit also has a zero voltage circuit breaker, which will be disabled in the event of a power outage, avoiding the danger of having the unit start up automatically upon the power supply being restored.

5

Clamping Screw SetupBefore you start grinding, the chain should be placed between both of the attachment guides. The tooth to be sharpened should be placed against the stop. Watch out for the sharpening angle to correspond to the guides section. The type of chain to be sharpened should be determined using the sharpening block provided or by viewing the table on page 7.There you can also find out about cutting thicknesses, angles and dimensions.

Set the guides to the chain width using the set screw (A) so that it is firmly fixed in the clamping screw by the clamping lever control (B).Set the feed by set screw (E).On severely worn chains, the lateral position of the chain guide should be secured with a set screw (D).Set the top plate angle by means of the set screw, which can also be checked on the scale (F). The vice angle should be set up by the set screw (G).

Top Plate Angle Vice Angle

GrindingNow with the clamping screw adjusted and the vice angle set (Note: RHand LH teeth need to be differentiated), set the top plate angle, then leadthe grinding disk down to the tooth using the handle. Ensure your handsare clear of the grinding disk. The grind depth may be set by the set screw(K).With the clamping lever loosened (B), the set screw is being screwed orunscrewed (E) until the grinding disk to sharpen will touch the tooth.During the grinding procedure, pull the chain to the guide (L) carefully.Note: wear gloves when performing this job!

Some types of saw-chains require that the clamping screw be tilted by 5° – 10° (cf: Table: space Tilt Angle).Note the notches (Fig. 9).

To start sharpening the chain, turn the grinder on and gently lower the handle until it comes into contact with the chain. Mark the first tooth you are sharpening with a chalk line or texta mark, then grind the teeth all in one direction, then turn the clamping screw (mind the angle), then grind the teeth in the opposite direction.With worn chains, the lateral guide position (Fig. 10 Position M) should be set for the grinding disk to not touch the guide. Avoid allowing the grinding disk to touch any part of the chain other than the section being sharpened, as the chain may easily be damaged.

6

Grinding Depth GaugeDetermine the correct height of the depth gauge using the table below. When grinding, the depth gauge, the vice angle (G) should always be 0.Set the supporting strut and holder at 90°.The grind depth may be set using set screw K.

Dimensions

7

Parts List

If you have any further questions regarding the use of this product, please contact the Kogan.com customer support team.

8