1

22

33

Table of Contents

Specifi cations 1

Adjustments 2

Using the Reticle 8

Maintenance 16

Troubleshooting 18

SS Warranty 19

1

SpecificationsTube Diameter 30 mm

Length 10.2 in

Weight 14.1 oz

Eye Relief 5.0-3.1 in

Field of View @ 100 Yards 24.8-99.9 ft

Exit Pupil 6-10.5 mm

Parallax Setting 100 yds

Submersible Yes

Diopter Compensation -2~+1 dpr

Adjustment Value 0.1 MRAD

Total Adjustment Range 55 Mils

2

AdjustmentsDiopter AdjustmentThe diopter adjustment, more commonly known as the reticle focus, is used to focus the reticle to the individual shooter’s eye.

Focusing the Reticle1. Rotate the fast-focus eyepiece clockwise until it stops.2. Look through the scope at a blank wall or clear sky.

This is necessary so your eye does not naturally attempt to focus on an object you are aiming at, rather than focusing solely on the reticle.

3. Slowly rotate the fast-focus eyepiece counter-clockwise until the reticle ap-pears as focused and clear as possible.

3

TipThe dioptric adjust-ment has no effect on target clarity, it is used to focus the reticle only. It is not necessary to re-adjust the diopter each time you use the scope. The only time it will be nec-essary to re-adjust is if your eyesight changes.

Diopter Adjustment

4. Without the scope, look at surrounding objects allowing your eye to rest and adjust back to normal conditions.This is necessary because your eye will naturally try to compensate for an out-of-focus reticle while you are trying to focus it with the dioptric adjustment.

5. Quickly bring the scope up to your eye, still aiming at the blank wall or clear sky, to confi rm the reticle appears clear and focused. If it still appears fuzzy or out-of-focus, repeat steps 2-5.

4

Magnifi cation AdjustmentThe magnifi cation ring, also known as the power selector, is used to adjust the amount of magnifi cation the scope provides at one time. To adjust the magnifi cation or power, simply rotate the magnifi cation ring to the desired position. Included with the scope, are (3) interchangeable throwlevers measuring 5mm, 10mm and 15mm in length, giving the shooter the ability to pick which is best for their setup. The interchangeable throwlevers thread directly into the magnifi cation ring to help the shooter change magnifi cation quickly and seamlessly.

Magnifi cation Adjustment

5

Elevation AdjustmentThe elevation adjustment is used to adjust the bullet’s point-of-impact (POI) up or down. The adjustment value per click and direction are marked on the top face of the turret. To adjust POI up, rotate the turret counter-clockwise. To adjust POI down, rotate the turret clockwise.

Windage AdjustmentThe windage adjustment is used to adjust the bullet’s point of impact (POI) left or right. The adjustment value per click and direction are marked on the face of the turret. To adjust POI to the left, rotate the windage turret clockwise. To adjust POI to the right, rotate the windage turret counter-clockwise.

6

Re-Zeroing the Turrets1. Loosen the (3) hex- head screws located on the rim of the turret. Completely

removing these screws from the turret is not necessary. Approximately one turn on each screw will disengage turret from internal adjustment post. The turret should spin freely with no clicks.

2. Rotate the turret until “0” is aligned with zero reference line on scope body.

3. While applying slight down-ward pressure on turret, evenly tighten the (3) set screws. Do not over tighten. Using your thumb and fore-fi nger to hold the short end of wrench while tightening will supply suffi cient torque.

fi nger to hold the short end of

Set Screw

7

Illumination Control AssemblyThe illumination control assembly is the turret module located on the left side of the rifl escope. It consists of the illumination adjustment, battery compartment and spare battery compartment. Each compartment is separated and waterproof. The illumination adjustment, also known as the rheostat, is used to ad-just the brightness of the illuminated section in the reticle. To adjust the illumination brightness, simply rotate the adjustment knob counter-clockwise to decrease brightness and clockwise to increase brightness. The brightness settings are marked with corresponding numbers 1-10. (10 is the brightest, 1 is the dimmest.) The dots between each of the numbers are “OFF” positions. If there is a certain setting you use most of the time, you can rotate just one click to an “OFF” position and just one click back to your preferred setting.

just the brightness of the illuminated section in the reticle. To adjust the illumination brightness, simply rotate the adjustment knob counter-clockwise to decrease brightness and clockwise to increase brightness. The brightness settings are marked with corresponding numbers 1-10. (10 is the brightest, 1 is the dimmest.) The dots between each of the numbers are “OFF” positions. If there is a certain setting you use most of the time,

the illumination brightness, simply rotate the adjustment knob counter-clockwise to decrease brightness and clockwise to increase brightness. The brightness settings are marked with corresponding numbers 1-10. (10 is the brightest, 1 is the dimmest.) The dots between each of the numbers are “OFF” positions. If there is a certain setting you use most of the time,

Illumination Control

8

Using the ReticleRangingThe SS 1-4X24IR rifl escope utilizes a Mil-based reticle and provides the shooter with accurate target dis-tances utilizing the target ranging references. The ranging references can be used to range objects 72”, 36”, or 24” tall, as well as any object 18” wide. This gives you the ability to range objects such as human silhou-ette-sized targets, IPSC silhouettes, deer, hogs and even coyotes.

Bracket > Divide > Range24” TALL TARGET

= 200YARDS

(RANGE / 3)

200

300

400500600800

36” TALL TARGET

= 300YARDS

(RANGE / 2)

200

300

400500600800

Bracket > Range72” TALL TARGET

= 200YARDS

200

300

400500600800

18” WIDE TARGET

= 300YARDS

200

300

400500600800

9

The second focal plane, Illuminated Mil-Quad DM reticle, gives the shooter better target acquisition in CQB scenarios while maintaining the ability to range and provide aiming points at max magnifi cation.

The new Illuminated Mil-Quad DM Reticle has integrated aiming points for 100, 200, and 300 yards for most 5.56 and 7.62 rounds.

10

Using the ReticleThere are a few different ways the reticle can be utilized. Examples are listed in the following pages.

Aiming PointsExample 1Zero the center dot in the reticle at 200 yards. and utilize the top of the diamond for the 100 yard aiming point and the bottom of the diamond for the 300 yard aiming point.

The actual point of impact vs. point of aim:M852 7.62 168 Grain @ 2600 FPS .35 Mils Low @ 100 yards, Zero 200 yards, .05 Mils High at 300 yards M80 7.62 147 Grain @ 2850 FPS .45 Mils Low @ 100 yards, Zero 200 yards, .15 Mils High at 300 yards M118LR 7.62 175 Grain @ 2600 FPS .35 Mils Low @ 100 yards, Zero 200 yards, .05 Mils High at 300 yards M193 5.56 55 Grain @ 3100 FPS .55 Mils Low @ 100 yards, Zero 200 yards, .15 Mils High at 300 yards M855 5.56 62 Grain @ 3000 FPS .55 Mils Low @ 100 yards, Zero 200 yards, .15 Mils High at 300 yards

1111

12

Using the ReticleAiming PointsExample 2Zero the top point of the diamond at 100 yards and use the center dot for the 250 yard aiming point and the bottom of the diamond for the 350 yard aiming point.

The actual point of impact vs. point of aim:M852 7.62 168 Grain @ 2600 FPS Zero 100 yards, .05 Mils Low @ 250 yards, .10 Mils Low at 350 yards M80 7.62 147 Grain @ 2850 FPS Zero 100 yards, .15 Mils High @ 250 yards, .20 Mils High at 350 yards M118LR 7.62 175 Grain @ 2600 FPS Zero 100 yards, .05 Mils Low @ 250 yards, .00 Mils High at 350 yards M193 5.56 55 Grain @ 3100 FPS Zero 100 yards, .25 Mils High @ 250 yards, .20 Mils High at 350 yards M855 5.56 62 Grain @ 3000 FPS Zero 100 yards, .25 Mils High @ 250 yards, .30 Mils High at 350 yards

TipYou can look over our subtensions and develop aiming points for the caliber or application of your choice. You can also just simply sight the center dot in at 100 yards and use it like a standard crosshair.

1313

14

Using the Reticle

Aiming PointsExample 3Zero the top point of the diamond in 200 yards and use the center dot for a 300 yard aiming point and the bottom of the diamond for the 400 yard aiming point.The actual point of impact vs. point of aim:M852 7.62 168 Grain @ 2600 FPS Zero 200 yards, .05 Mils High @ 300 yards, .10 Mils Low at 400 yards M80 7.62 147 Grain @ 2850 FPS Zero 200 yards, .15 Mils High @ 300 yards, .20 Mils High at 400 yards M118LR 7.62 175 Grain @ 2600 FPS Zero 200 yards, .05 Mils High @ 300 yards, .00 Mils High at 400 yards M193 5.56 55 Grain @ 3100 FPS Zero 200 yards, .15 Mils High @ 300 yards, .10 Mils High at 400 yards M855 5.56 62 Grain @ 3000 FPS Zero 200 yards, .15 Mils High @ 300 yards, .20 Mils High at 400 yards

1515

16

Maintenance

Lens CleaningNever use household glass/all-purpose cleaners!

• Use high-quality glass cleaning solution and a lens cloth or lens pen. Using anything other than lens cleaning products can cause permanent damage to lenses.

• Remove any dirt or debris from lenses before cleaning. You can blow it out with your breath or, if necessary, low-pressure compressed air. Wiping lenses that have dirt/debris on them can cause permanent damage.

• Start with a small amount of lens cleaning solution and wipe lens in a circular motion. Increase the amount of solution and repeat if necessary.

The SS 1-4x24 rifl escope requires very little maintenance besides occasionally cleaning the lenses or replacing the illumination battery. The scope’s exterior can be wiped down with a clean, dry cloth when necessary.

17

LubricationAll moving adjustments have been permanently lubricated at the factory. Lubrication of the scope’s components is not necessary.

Battery ReplacementThe illuminated reticle is powered by a CR2032 battery. To replace the bat-tery, unscrew the battery module cap, replace battery and screw module cap back on. When installing new battery, be sure the fl at, shiny side of battery is facing out. The outer compartment of the battery module assembly is used to safely store an extra battery.

Maintenance

of the scope’s components is not necessary.

The illuminated reticle is powered by a

tery, unscrew the battery module cap, replace battery and screw module cap back on. When installing new battery, be sure the fl at, shiny side of battery is facing out. The outer compartment

used to safely store an extra battery. BatteryCompartment

Illumination Adjustment

Spare Battery Compartment

18

TroubleShootingRifl e won’t sight in because scope won’t adjust any more.The most common cause of this is a mounting issue, not a scope issue. Check all mounting hardware to ensure everything is tight and in good condition. This prob-lem can also occur when the scope is mounted too far above the bore’s axis. The SS 1-4X24IR rifl escope has been optimized for use on AR-Style platforms. It is recom-mended to mount the center axis of the scope 1.5” above the mounting rail for the best performance.

The turrets spin freely and do not click when adjusting.Although it is very uncommon, it is not impossible for the turret set screws to be-come loose over time. Make sure the screws located around the outside rim of the turret are tight. See “Re-Zeroing the Turrets” section on page 4 for instructions on resetting the turret.

19

The SS rifl escope line is backed by a very simple lifetime warranty: if your SS rifl escope ever becomes damaged or defective, under normal use, we will repair or replace it. That’s all there is to it! No registration card or proof of purchase needed. It doesn’t even matter if you are the fi rst or tenth owner, you can be confi dent your purchase is backed by the same great service and guarantee as the day it left the factory. The SS warranty does not cover loss, theft or intentional damage.

Warranty

Notes

Notes

24