T916 Treadmill Owner’s And Assembly Manual Addendum · T916 Treadmill Owner’s And Assembly Manual Addendum ... Manual. Do not use attachments not recommended by the ... plastic

T916 Treadmill Owner’s And Assembly Manual Addendum

P/N 19-1001_F

STRONGER THAN EVER™® ®

Med-Fit Systems, Inc., exclusivemanufacturers of Nautilus®

Commercial Fitness Equipment

IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONSThis page is in addition to the Important Safety Instructions page in the printed Owner’s Manual

This icon means a potentially hazardous situation exists which, if not avoided, could result in death or serious injury.

When using an electrical appliance, basic precautions should always be followed, including the following:

1. Read all instructions before using this appliance.

2. DANGER - To reduce the risk of electric shock, always unplug this appliance from the electrical outlet immediately after using and before cleaning.

3. WARNING - To reduce the risk of burn, fire, electric shock, or injury to persons:

• This appliance should never be left unattended when disconnected from the outlet. It should remain connected to the outlet at all times, except when putting on or taking off parts;

• Close supervision is necessary when this appliance is used near children, invalids, or disabled persons;

• This appliance should never be used by children, invalids, or disabled persons;

• Use this appliance only for its intended use as described in the Owner’s Manual. Do not use attachments not recommended by the manufacturer;

• Never operate this appliance if it has a damaged cord or plug, if it is not workingproperly, if it has been dropped or damaged, or if it has been dropped into water. If the cord is damaged, it must be replaced using the special cord or assembly available exclusively from the manufacturer;

• Keep the cord away from heated surfaces;

• Never drop or insert any object into any opening of this appliance;

• Do not use this appliance outdoors;

• To disconnect the appliance, turn all controls to the “off” position, then remove the plug from the outlet.

4. WARNING - Connect this appliance to a properly grounded outlet in accordancewith all local codes and ordinances. See Grounding Instructions...

Notice: This Addendum provides important information regarding Important Safety Instructions, Grounding Instructions, Power Plug Receptacle Information, Assembly Instructions, Commercial

Limited Warranty Information and Contact Information that is not found in the printed Owner’s Manual.

If you need assistance, please contact Med-Fit Systems Customer Excellence at 800-235-2233

3

GROUNDING INSTRUCTIONS - SAVE THESE INSTRUCTIONSThis section is in addition to the Important Safety Instructions page in the printed Owner’s Manual

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER - Improper connection of the equipment-grounding conductor can result in a riskof electric shock. Check with a qualified electrician or serviceman if you are in doubt as towhether this appliance is properly grounded. Do not modify the plug provided with thisappliance; if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

POWER PLUG RECEPTACLESThis section replaces the Power Plug Receptacles section in the printed Owner’s Manual

If your T916 Treadmill was produced after January 2011, it is equipped with a hardwired power cord that extends from the front of the machine. The Rear Power Receptacle is no longer an available option after this production date. Make sure to position the machine so that the power cord is not a trip hazard and cannot become damaged during normal use.

If you have any questions or concerns regarding the hardwired power cord, or its safe use, please contact a Med-Fit Systems Customer Excellence representative at 800-235-2233, or 276-773-2881 outside the United States.

4

PREVENTIVE MAINTENANCEThis section is in addition to the Preventive Maintenance section in the printed Owner’s Manual

Med-Fit Systems, and our suppliers, have tested and determined that it is acceptable to add apure silicone fluid (PDMS) to the walking belt and deck in cases where machine performance isaffected by a high-friction condition. Adding a pure silicone fluid will not damage the friction-control surface.

Med-Fit Systems only recommends Clearco-brand PSF-100cSt standard viscosity pure siliconefluid. Apply 1-1/2 ounces of the pure silicone fluid between the walking belt and deck, towardsthe center and from the front to the rear. Allow the belt to run at a moderate speed for at least 5minutes before using the machine again.

If you have any questions or concerns regarding pure silicone fluid, or its safe use, pleasecontact a Med-Fit Systems Customer Excellence representative at 800-235-2233, or276-773-2881 outside the United States.

MOTOR COVERS INSTALLATION INSTRUCTIONSThis procedure replaces Steps 3, 4, and 5 (pages 4 and 5) in the printed Assembly Manual

Tools And Components

Fasteners Included:

(25) 10-32 x 3/4 SS Pan Head Screw

(16) Decorative Plastic Cap

(4) 10-32 x 1/2 SS Pan Head Screw

Components Included:

(1) Top Motor Cover

(1) LH Side Motor Cover

(1) RH Side Motor Cover

(1) Front Motor Cover

(6) Side Bracket

(1) Top Bracket

Tools Required:

#2 Phillips Screwdriver

Proper Lifting Technique

assembly questions? call 800-235-2233 for help. 5

Figure 1

Figure 2

Figure 3

Step 1. Install Side Brackets(Figures 1, 2 and 3)

1-1 Place the (16) plastic caps on (16) 10-32 x 3/4 screws;

1-2 Secure (2) side brackets to the LH side cover using (2) screws with plastic caps;

1-3 Secure (2) side brackets to the RH side cover using (2) screws with plastic caps;

1-4 Secure (2) side brackets to the top cover using (2) screws with plastic caps.

Note: make sure the end of the bracket with the hole closest to the edge is towards the cover.

Note: do not tighten any screws at this time. The screws should be loose enough for the brackets to pivot freely.


Figure 4

Figure 5

Figure 6

Step 2. Attach Side Covers To Front Cover(Figures 4 and 5)

2-1 Align the holes in the left side of the front cover with the brackets attached to the LH side cover and secure using (2)screws with plastic caps;

2-2 Align the holes in the right side of the front cover with the brackets attached tothe RH side cover and secure using (2)screws with plastic caps.

Note: do not tighten any screws at this time.

Step 3. Install Cover Assembly To Frame(Figure 6)

3-1 Route the power cord through the center opening of the front cover;

Note: the rear power receptacle is no longer available on Treadmills produced after January 2011.

3-2 Spread the side covers slightly and slide the entire cover assembly onto the frame;

3-3 Secure the front cover to the frame using (1) 10-32 x 3/4 screw in the center hole only;

Note: do not install screws in the two outer holes of the front cover. Installing these screws will prohibit the covers from aligning properly.

3-4 Secure the LH side cover along the outside of the frame using (3) 10-32 x 3/4 screws;

3-5 Secure the RH side cover along the outside of the frame using (3) 10-32 x 3/4 screws.



Figure 7

Figure 8

Figure 9

Step 4. Install Top Bracket(Figure 7)

4-1 Secure the top bracket to the LH and RH side covers using (2) screws with plastic caps.


Step 5. Install Top Cover(Figures 8 and 9)

5-1 Place the top cover into position and align the holes with the top bracket;

5-2 Secure the top cover to the top bracket using (2) screws with plastic caps;

5-3 Align the hole in the rear of the LH side cover with the bracket attached to the top cover and secure using (1) screw with plastic cap;

5-4 Align the hole in the rear of the RH side cover with the bracket attached to the top cover and secure using (1) screw with plastic cap;

5-5 Secure the top cover to the kick plate using (2) 10-32 x 1/2 screws;

5-6 Secure the LH side cover along the inside of the upright using (2) 10-32 x 1/2 screws;

5-7 Secure the RH side cover along the inside of the upright using (2) 10-32 x 1/2 screws.



Figure 10

Figure 11

Figure 12

Step 6. Final Adjustment(Figures 10, 11, and 12)

Warning: make sure all fasteners are secure before moving on.

6-1 Make sure the covers are positioned properly before tightening all the screws. All gaps should be even and all edgesshould be aligned;

Note: some screws may have to be loosened and then re-tightened to ensure the best possible fit.

6-2 Secure all plastic caps by pressing down until the cap snaps closed;

6-3 Complete Step 6 as shown in the printed Assembly Manual.


COMMERCIAL LIMITED WARRANTY INFORMATIONThis page replaces the Commercial Warranty Information page in the printed Owner’s Manual

Please read these warranty terms and conditions carefully before using your Med-Fit Systems, Inc. (Med-Fit) product. By using the product, you are consenting to be bound by the following warranty terms and conditions.

LIMITED WARRANTY.

Med-Fit warrants all new Nautilus® Commercial products to be free from defects in materials and manufacture for the warranty periods set forth below. The warranty periods commence on the invoice date of the original purchase. This warranty applies only against defects discovered within the warranty period and extends only to the original purchaser of the products. Partsrepaired or replaced under the terms of this warranty will be warranted for the remainder of theoriginal warranty period only. To claim under this warranty, the purchaser must notify Med-Fit,or an authorized Med-Fit dealer, within 30 days after the date of discovery of any nonconformity and make the affected product available for inspection by Med-Fit or its service representative. Med-Fit’s obligations under this warranty are limited as set forth below.

WARRANTY PERIODS AND COVERAGE.

Commercial Strength Products manufactured and sold after September 1, 2013.Frame parts and weldments: LifetimeMechanical part: 3 yearsWear parts: 6 monthsLabor: 1 year (United States and Canada only)

Full-Commercial Cardiovascular Products manufactured and sold after September 1, 2013.Frame parts: LifetimeMotor: 10 years

Mechanical parts and weldments: 3 yearsElectrical parts: 3 yearsWear parts (including touchscreen): 1 yearLabor: 1 year (United States and Canada only)

8-Series Cardiovascular Products manufactured and sold after September 1, 2013.(for full-commercial usage)Frame parts: 7 yearsMechanical parts and weldments: 1 yearLabor: 1 year (United States and Canada only)

Electromagnetic (Eddy) Brake parts: 10 years

8-Series Cardiovascular Products manufactured and sold after September 1, 2013.(for light-commercial usage)Frame parts: 7 yearsMotor: 5 yearsMechanical part and weldments: 3 yearsWear parts (including display): 1 yearLabor: 1 year (United States and Canada only)

10

COMMERCIAL LIMITED WARRANTY INFORMATION continued

3. The warranty does not cover damage or equipment failure caused by electrical wiring not in compliance with electrical codes or Med-Fit owner’s manual specifications, or failure toprovide reasonable and necessary maintenance as outlined in the owner’s manual. Nautilus® Commercial Strength and Full-Commercial Cardiovascular products are guaranteed against structural defects for the life of the product. Paint and powder coated surfaces are notincluded in this explicit warranty.

Nautilus® Commercial products shall be covered by the Assumed Warranty Liabilities only if within the original manufacturer warranty term period and only if all warranty conditions have previously been complied with. Med-Fit shall be entitled to verify the validity of the original warranty by requiring the warranty claimant to present evidence in the form of a serial number and proof of purchase.

4. Except in Canada, Med-Fit does not pay labor outside the United States.

2. Current Commercial Strength products include F3, P3, P4, S3, S4, S5, S6, S8, and S9 lines. Current Full-Commercial Cardiovascular products include 9-series and 10-series lines.

8-Series Cardiovascular products are warranted for both full-commercial use and light-commercial use; 6-Series Cardiovascular products are warranted for light-commercial useonly. Light-commercial use is defined as use in non-fee paying clubs and facilities, and lessthan 6 hours daily use.

CONDITIONS AND RESTRICTIONS.

This warranty is valid only in accordance with the conditions set forth below:

1. The warranty applies to the Nautilus® Commercial product only while:a. It remains in the possession of the original purchaser and proof of purchase is

demonstrated,b. It has not been subjected to accident, misuse, abuse, improper service, or non-Med-Fit

modification, andc. Claims are made within the warranty period.

WARRANTY PERIODS AND COVERAGE continued.

6-Series Cardiovascular Products manufactured and sold after September 1, 2013.(for light-commercial usage)Frame parts: 7 yearsMotor: 5 yearsMechanical parts and weldments: 2 yearsWear parts (including display): 1 yearLabor: 1 year (United States and Canada only)

11


5. The warranty does not cover the following:a. Damage due to normal wear and tear as defined by items subject to normal use and/or

exposure, consumables and cosmetic items, including, but not limited to, grips, seats, paint, scratches, and decals,

b. Repairs performed on Nautilus® Commercial products missing a serial number or with a serial tag that has been altered or defaced,

c. Service call to correct installation of the product or instruct owners on the use of theproduct,

d. Pickup and delivery involved with repairs,e. Products that are outside the warranty period,f. Any damage, failure, or loss caused by accident, misuse, neglect, abuse, improper

assembly, improper or lack of maintenance, Acts of God (such as, but not limited to, floods, power surges, etc.), or failure to follow instructions or warnings in the owner’s manual,

g. Use of the product in an application not recommended by Med-Fit, or in a manner or environment for which it was not designed,

h. Adjustments, adaptations, modifications, refurbishing, or remanufacturing will exclude all warranty coverage, and

i. Extended Warranties: Med-Fit will not be responsible for any extended coverage terms offered by a distributor or service provider other than Med-Fit.

CONDITIONS AND RESTRICTIONS continued.

DISCLAIMER AND RELEASE.

The warranties provided herein are the exclusive warranties given by Med-Fit and supersede any prior, contrary, or additional representations, whether oral or written. Any implied warranties, including the warranty of merchantability or fitness for a particular purpose that apply to any parts described above are limited in duration to the periods of express warranties given above for those same parts. Med-Fit hereby disclaims and excludes those warranties thereafter. Somestates do not allow limitations on how long an implied warranty lasts, so the above limitationmay not apply to you. Med-Fit also hereby disclaims and excludes all other obligations orliabilities, express or implied, arising by law or otherwise, with respect to any nonconformanceor defect in any product including, BUT NOT LIMITED TO: (A) ANY OBLIGATION, LIABILITY,RIGHT, CLAIM OR REMEDY IN TORT, WHETHER OR NOT ARISING FROM THENEGLIGENCE OF MED-FIT OR ITS SUPPLIERS (WHETHER ACTIVE, PASSIVE, ORIMPUTED); AND (B) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY FOR LOSSOF OR DAMAGE TO ANY EQUIPMENT. This disclaimer and release shall apply even if theexpress warranty set forth above fails of its essential purpose.

12


EXCLUSIVE REMEDIES.

For any product described above that fails to conform to its warranty, Med-Fit will provide, attheir option, replacement of failed parts/whole goods or refund the current cost of the product.Med-Fit Limited Warranty parts may be obtained by contacting the authorized dealer from whomyou purchased the item. You may be charged duties and freight associated with receiving theproduct. THESE SHALL BE THE SOLE AND EXCLUSIVE REMEDIES OF THE BUYER ORANY BREACH OF WARRANTY.

EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL DAMAGES.

Med-Fit and/or its suppliers shall have no obligation or liability, whether arising in contract(including warranty), tort (including active, passive, or imputed negligence and strict liability),or otherwise, for damage to the product, property damage, loss of use, revenue or profit,cost of capital, cost of substitute product, additional costs incurred by the purchaser (by way ofcorrection or otherwise) or any other incidental, special, indirect, or consequential damages,whether resulting from non-delivery or from use, misuse, or inability to use the product. Thisexclusion applies even if the above warranty fails of its essential purposes and regardless ofwhether such damages are sought for breach of warranty, breach of contract, negligence, or strict liability in tort or under any other legal theory. Some states do not allow the exclusion orlimitation of incidental or consequential damages, so the above limitation may not apply to you.

13

If you need assistance, please have both the serial number of your machine and the date of purchase available when you call Med-Fit Systems Customer Excellence.

TECHNICAL & CUSTOMER SERVICE

phone: 276-773-2881toll free: 800-235-2233fax: 276-773-2298e-mail: [email protected]: www.nautiluscommercial.com

SALES & CORPORATE HEADQUARTERS

Med-Fit Systems, Inc.Corporate Office543 East Alvarado StFallbrook, CA 92028phone: 760-451-3038toll free: 800-831-7665web: www.medfitsystems.com

MANUFACTURING FACILITY

709 Powerhouse RdIndependence, VA 24348phone: 276-773-2881toll free: 800-874-8941web: www.nautiluscommercial.com

CONTACT INFORMATIONThis page replaces the Contact Information page in the printed Owner’s Manual

14

Documents

T916 Treadmill Owner’s And Assembly Manual Addendum · T916 Treadmill Owner’s And Assembly Manual Addendum ... Manual. Do not use attachments not recommended by the ... plastic