Embed Size (px)
Citation preview
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 1
LTU and Beam DumpLTU and Beam DumpInstallation Installation
April 16, 2007April 16, 2007
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 2
LTU and Beam Dump Installation LTU and Beam Dump Installation
LTU Beamline DesignLTU Beamline OverviewLTU BTH West Section 72 Installation Drawing ExampleQuadrupole Support GeometryQuadrupole Support Modal FEAQuadrupole Alignment Stage GeometryLTU Supports Geometry
LTU Installation SequenceBeam Dump GeometrySafety
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 3
LTU Beamline Overview
11 Sections (71-82)27 meter nominal section lengthVAT vacuum valve isolates each sectionTwo 40l/s ion pumps per sectionOne vacuum gauge pair per sectionOne roughing valve/pump out per section
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 4
LTU BTH West
BSY Muon Plug - LTU Start
BTH west to BTH Transition
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 5
Section 72 Installation Drawing Example
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 6
Quadrupole Support Geometry
Mount Plate
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 7
Quadrupole Support Modal FEA
Mode # frequency direction
1 113 Z
2 118 X
3 292 X
4 310 X
5 345 Y
6 385 X
7 393 X
8 398 X
9 456 Y
10 505 X
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 8
Quadrupole Alignment Stage Geometry
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 9
LTU Supports Geometry
Device Support Component Support Drift Support
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 10
Device and Quadrupole Support Installation
GROUT
BTH FLOOR
SUPPORTCOLUMN
PRE- ALIGNEDMOUNT PLATE
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 11
Core drill support mount hole patterns serially starting at section 71.
Install quadrupole and device mount plates.
Install Component and Drift supports.
Install quadrupole, dipole, and diagnostics supports.
Install Quadrupoles and Dipoles.
Install Diagnostics, collimators, and single beam.
Install vacuum drifts, ion pumps, VAT valves, bellows modules, and vacuum gauges.
Leak check and pump down section by section from 71 through 82.
LTU Installation Sequence
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 12
Beam Dump Geometry
BEAM DUMP
BEND MAGNETS
SAFETY DUMP
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 13
Beam Dump Geometry
QUARUPOLE MAGNET
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 14
Beam Dump Geometry
STOPPER
DUMP BEND MAGNETS
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 15
Beam Dump Geometry
SAFETY BEND MAGNETS
QUADRUPOLE MAGNETS
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 16
Beam Dump Geometry
DUMP SHIELDING
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 17
Beam Dump Geometry
BEND MAGNETS
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 18
Beam Dump Geometry
DUMP LINE
SAFETY BEND MAGNETS PROTECTION COLLIMATOR
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 19
Beam Dump Geometry
BEAM DUMP
OTR PROFILE MONITOR
T. Montagne
LTU – Beam Dump Installation Planning [email protected]
April 16, 2007 20
Safety
Rigging and Installation will be planned, reviewed, and performed according to SLAC Rigging and Safety Procedures.
