12
WEBSITE: www.jdsu.com/test COMMUNICATIONS TEST AND MEASUREMENT SOLUTIONS T-BERD®/MTS-6000A MSAM Specifications Ethernet Test interfaces/bit rates 10/100/1000 M Electrical Dual-port capable 100 M Ethernet Optical Dual-port capable Gigabit Ethernet (Optical) Dual-port capable 10 GE WAN Phy (9.9G) Dual-port capable 10 GE LAN Phy (10.3G) Dual-port capable Interface type RJ45 SFP XFP XFP - Tunable General Line-rate traffic Tx and Rx for all interfaces Single-stream generation/analysis 10-stream generation/analysis per stream Auto-discovery of test sets Modes of operation Terminate Monitor Thru (intrusive) Loopback Half duplex Full duplex Timing Recovered from Rx Internal (Stratum 3) Recovered from external (bits/set) Frequency offset Tx/Rx VLAN stacking (Q-in-Q) SVLAN tag-editable fields SVLAN ID SVLAN priority SVLAN DEI SVLAN TPID CVLAN ID CVLAN priority Supports up to 8 stacked VLAN tags VPLS VPLS parameters - MAC addresses VPLS parameters - Frame type VPLS parameters - Ethertype VPLS tunnel and VC label - Lavel, CoS, TTL VPLS control word - Reserved bits, sequence number MAC in MAC/PBT/PBB 802.1ah Parameters - MAC address B-Tag - TPI, VID, priority, DEI I-Tag - TPI, SID, priority, DEI, NCA, Res1, Res2 MPLS Single-label support Stacked-label support - Up to 2 Editable parameters/results - Label Editable parameters/results - CoS Editable parameters/results - TTL MPLS-TP MPLS-TP label support (tunnel and VC) Line-rate traffic generation Traffic analysis Editable parameters/results - Label Editable parameters/results - Priority Editable parameters/results - TTL Rx filters Y.1731 OAM generation Y.1731 OAM analysis CCM message generation and analysis AIS generation Common header label - PW, LSP, Section OAM alert label (Label 14) from ITU-T G.8114 GAL (Label 13) + ACH from IETF Draft Generate/monitor OAM messages - CCM - LBM/LBR - AIS Simultaneous OAM and background traffic generation Ethernet features Layer 1 (unframed) Bit Error testing patterns High-frequency test pattern Low-frequency test pattern Mixed-frequency test pattern Random data pattern (RPAT) Jitter-tolerance test pattern (JTPAT) Supply-noise test sequence (SPAT) Layer 2 (framed) Bit Error testing patterns Compliant random-data pattern (CRPAT) Compliant jitter-tolerance pattern (CJPAT) Compliant supply-noise pattern (CSPAT) Framed Pattern test PRBS (2^11-1, 2^15-1, 2^20-1, 2^23-1, 2^31-1 and inverse) All 1s, all 0s 1:3, 1:7, 3:1, 7:1, 2 in 8 User-defined Ethernet generator Frame type 802.3 DIX VPLS with inner and outer MAC MAC in MAC 802.1ah EtherType field-editable MAC addressing Destination MAC address - Unicast Destination MAC address - Broadcast Destination MAC address - Multicast Source MAC address - User-defined Source MAC address - Auto-increment MAC frame size 64, 128, 256, 512, 1024, 1280, 1518, user-defined, jumbo (to 10 k) User-defined Jumbo (to 10 k) Random VLAN VLAN tagging 802.1q VLAN tag-editable fields - Priority - VID

T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

Embed Size (px)

Citation preview

Page 1: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

website: www.jdsu.com/test

COMMUNICATIONS TEST AND MEASUREMENT SOLUTIONS

T-BERD®/MTS-6000A MSAM Specifications

EthernetTest interfaces/bit rates

10/100/1000 M Electrical Dual-port capable100 M Ethernet Optical Dual-port capableGigabit Ethernet (Optical) Dual-port capable10 GE WAN Phy (9.9G) Dual-port capable10 GE LAN Phy (10.3G) Dual-port capable

Interface type

RJ45SFPXFPXFP - Tunable

General

Line-rate traffic Tx and Rx for all interfacesSingle-stream generation/analysis10-stream generation/analysis per streamAuto-discovery of test sets

Modes of operation

TerminateMonitorThru (intrusive)Loopback Half duplexFull duplex

Timing

Recovered from RxInternal (Stratum 3)Recovered from external (bits/set)Frequency offset Tx/Rx

VLAN stacking (Q-in-Q)SVLAN tag-editable fieldsSVLAN IDSVLAN prioritySVLAN DEISVLAN TPIDCVLAN IDCVLAN prioritySupports up to 8 stacked VLAN tagsVPLS VPLS parameters - MAC addressesVPLS parameters - Frame typeVPLS parameters - EthertypeVPLS tunnel and VC label - Lavel, CoS, TTLVPLS control word - Reserved bits, sequence numberMAC in MAC/PBT/PBB 802.1ahParameters - MAC addressB-Tag - TPI, VID, priority, DEII-Tag - TPI, SID, priority, DEI, NCA, Res1, Res2MPLSSingle-label supportStacked-label support - Up to 2Editable parameters/results - LabelEditable parameters/results - CoSEditable parameters/results - TTLMPLS-TPMPLS-TP label support (tunnel and VC)Line-rate traffic generationTraffic analysisEditable parameters/results - LabelEditable parameters/results - PriorityEditable parameters/results - TTLRx filtersY.1731 OAM generationY.1731 OAM analysisCCM message generation and analysisAIS generationCommon header label - PW, LSP, SectionOAM alert label (Label 14) from ITU-T G.8114GAL (Label 13) + ACH from IETF DraftGenerate/monitor OAM messages- CCM- LBM/LBR- AISSimultaneous OAM and background traffic generation

Ethernet features

Layer 1 (unframed) Bit Error testing patternsHigh-frequency test patternLow-frequency test patternMixed-frequency test patternRandom data pattern (RPAT)Jitter-tolerance test pattern (JTPAT)Supply-noise test sequence (SPAT)Layer 2 (framed) Bit Error testing patternsCompliant random-data pattern (CRPAT)Compliant jitter-tolerance pattern (CJPAT)Compliant supply-noise pattern (CSPAT)Framed Pattern testPRBS (2^11-1, 2^15-1, 2^20-1, 2^23-1, 2^31-1 and inverse)All 1s, all 0s1:3, 1:7, 3:1, 7:1, 2 in 8User-defined

Ethernet generator

Frame type802.3DIXVPLS with inner and outer MACMAC in MAC 802.1ahEtherType field-editableMAC addressingDestination MAC address - UnicastDestination MAC address - BroadcastDestination MAC address - MulticastSource MAC address - User-definedSource MAC address - Auto-incrementMAC frame size64, 128, 256, 512, 1024, 1280, 1518, user-defined, jumbo (to 10 k)User-definedJumbo (to 10 k)RandomVLANVLAN tagging 802.1qVLAN tag-editable fields - Priority - VID

Page 2: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

2

T-BERD/MTS-6000A MSAM SPECIFICATIONS

Ethernet OAMY.1731 Service OAM and 802.1ag CFMCCM messagesProgrammable CCM rateCCM type - Unicast, multiCastMEG ID end pointMaintenance domain levelAIS Tx/RxRDI Tx/RxLBR/LBM (Ping) - Unicast, multicastLTM/LTR (Trace)802.3ah Link OAMMode - Passive/activeVendor OUIVendor-specific infoMax PDU sizeUnidirectional linksRemote loopbackLink eventsVariable retrievalDying gaspLink faultCritical eventErrored symbol period eventErrored frame eventErrored frame period eventErrored frame second summary eventMAC frame payloadPRBS patternEditable digital wordFlow controlEmulation on/offPause framesTx insertPause quanta - definablePause frame analysis (for example, counts)

IP packet generator

IPIPv4 frame formatIPv6 frame formatTCP port numberUDP port numberIP addressingDestination IP address - User-definedSource IP Address - User-definedIPv4 editable fieldsToSDSCPFlagsProtocolTTL IPv6 editable fieldsTraffic classFlow labelNext headerHop limit

IP pingFast pingIP traceroute

Traffic Generator

Number of traffic enginesBandwidth contolledBandwidth specification in MbBandwidth granularityBandwidth specification in %Bandwidth utilization accuracy - 0.1%Burst mode - Burst size - 1 to 2 M framesBandwidth specified - DefinableContinuous TxOnce Tx - Definable frames/burstTraffic profilesConstant B/WRamp B/WBursty B/WFlood B/WTraffic generation in Mbps and % utilization

TCP/IP packet generator

10/100/1000 M Line rate stateful emulation1 GE Line rate stateful emulation10 GE Line rate stateful emulationConfigurable Src and Dest IP addressPacket lengthTCP/UDP traffic modesSource portDestination portListen portConfigurable TCP window sizeTCP client emulationTCP server emulationUp to 64 simultaneous TCP stateful sessionsSupports 4 background streamsCompatible with iPerf

RFC 2544

Asymmetric testingSymmetric testingThroughputFrame lossOut-of-sequence framesDelayBack to backJitterMaster/slaveConnectivity QuickCheckParallel testingDefinable frame sizeReport formatsGraphical resultsTotal-test-time display

Specifications cont’d.

ITU-T Y.1564

10 Traffic streamsService Configuration testService Performance testCommitted information rate (CIR)Extended IR (EIR)Maximum IR (MIR)Frame loss rate (FLR)Frame delay (FD)Frame delay variationConfigurable VLAN, priority, addressing, and pass/failThresholdsGraphical resultsSaved test profilesConfigurable DEI, TPID, TOX/DSCPInclusive of L2 Ethernet and IPv4Integrated TrueSpeed TCP traffic stream with background streamsAsymmetric testingOne-way delay with CDMA receiver

IETF RFC 6349

Automated TCP-Throughput test per RFC 6349Path MTU Detection testRound-Trip Time testWalk-the-Window testTCP-Throughput testTraffic-Shaping testTCP-Efficiency metricBuffer-Delay metricUp to 64 simultaneous TCP stateful sessionsGraphical results and report generationConfigurable file and window sizesTotal-test-time display

Layer 2 Transparency testing

Send/receive Ethernet control plane trafficEncapsulation supported - VLANEncapsulation supported - Q-in-QEncapsulation supported - Spanning TreeEncapsulation supported - Cisco protocols (Discovery, etc.)Encapsulation supported - GARPEncapsulation supported - STPSend/receive Ethernet control plane traffic- Spanning Tree frames Tx/Rx- Cisco discovery protocol- LDP frames Tx/Rx- Link aggregation LACP- Cisco UDLD, ISL, PagP, DTP, PVST-PVST+- MAC bridging 802.1d- VLAN-BRDGSTP- Custom frame builder

Page 3: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

3

T-BERD/MTS-6000A MSAM SPECIFICATIONS

Specifications cont’d.

Synchronous Ethernet ITU G.826x

10 GE Tx/Rx1000/100/10 M Tx/RxRecovered interface timing4.6 ppm frequency accuracySSM message decodeESMC message captureQuality message decodeDefinable SSM PDU rate (pps)Background data plane traffic generation

1588v2

1 GE Tx/Rx1588v2 master PRC emulation1588v2 slave emulationPacket delay variation measurements on control plane trafficGenerate up to 4 streams of background dataplane trafficFrame/packet capture and decode via WiresharkLayer 2 1588v2 messagingLayer 4 1588v2 messaging

Loopback

Manual (LLB)AutomaticLocalFar end

Delay

Round-trip delayOne-way delayDelay measurement accuracy

CAT-5 testing

Link speedLink statusCable statusCrossover/straight (MDI/MDIX)Distance to faultPin mappingPair lengthPolaritySkew

Capture/decode

Wirespeed capture up to 10 GbpsWirespeed capture up to 1000/100/10 MIntegrated Wireshark on the test set256 MB capture bufferTriggersTx and Rx captureFrame slicing

Expert decode/analysis

Decode/analysis capture filesDetect half-duflex portsDetect ICMP Layer IssuesIdentify Top TalkersTCP Layer Diagnosis - ex. Retransmissions

Traffic profiling

Detect and display up to 128 streams of live trafficSpecify filters for stream detectionStream classification

Network discovery

Automatically detect networks, domains, devices, and hosts

Traffic filtering

Ethernet (Layer 2) traffic filteringMAC source and destination addressFrame type/lengthVLAN IDVLAN priorityVLAN discoveryVLAN (Layer 2.5) tags - 802.1qTPIPriorityCFI/DEIVIDVLAN (Layer 2.5) tags - Q-in-Q, 802.1ahSVLAN IDSVLAN prioritySVLAN TPICVLAN IDCVLAN priorityIP (Layer 3) traffic filteringSource and destination IP addressSubnet maskIPv6 traffic class TOS/DSCP fieldsTCP/UDP (Layer 4) traffic filteringATP listen port

Errors Tx/Rx

Code error Tx/RxFCS error Tx/RxIP checksum Tx/RxBit error Tx/RxInsertion profile - OnceInsertion profile - RateInsertion profile - Burst

Alarms Tx/Rx

Local fault Tx/RxRemote fault Tx/Rx

Ethernet results

Custom resultsHistogram and graphical results scriptLink StatusLoss of signalLink activeFrame detectedSync obtainedVLAN-tagged frame detectedAuto-negotiation statusLink configuration ackLink advertisement statusPause capableRemote faultDestination MAC address when using ARPLink counts/statisticsBandwidth utilizationFrame rateTx MbpsRx MbpsRound-trip delayService-disruption timeReceived framesTransmitted framesReceived packetsTransmitted packetsPause framesLost framesOut-of-sequence framesOut-of-sequence packetsVLAN framesCVLAN IDSVLAN IDCVLAN prioritySVLAN priorityUnicast framesUnicast packetsMulticast framesMulticast packetsBroadcast framesBroadcast packetsFrame lengthPacket lengthPacket jitter, avgPacket jitter, max

Page 4: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

4

T-BERD/MTS-6000A MSAM SPECIFICATIONS

SONET/SDHTest interfaces/bit rates

STS-1 (e) Dual-port capableSTM-1 (e) Dual-port capableSTM-1 (o) Dual-port capableOC-3 Dual-port capableOC-12 Dual-port capableSTM-4 Dual-port capableOC-48 Dual-port capableSTM-16 Dual-port capableOC-192 Dual-port capableSTM-64 Dual-port capable

Laser type

SFPXFPXFP - Tunable

Modes of operation

TerminateMonitorThru (intrusive)Tributary scanDrop and insert

Timing

Recovered from RxInternal (Stratum 3)Recovered from external (bits/set)Recovered from 10 MHz clock

SONET/SDH features

SONET/SDH framingOverhead manipulation/analysisOptical/electrical power levelPRBS generationPM/SM TTI messages Tx/RxOverhead byte viewing/manipultionService disruption measurements- SD separation/debounce time setting- SD threshold time settingsSignal label generation/displayFrequency offset Tx/RxRound-trip delay measurementRTD measurement accuracyPRBS patterns215-1, 215-1 inverse2^20-1, 2^20-1 inverse2^23-1, 2^23-1 inverse2^31-1, 2^31-1 inverseProgrammable - 32 bitANSI and ITU implementationsAnomoly/Error generationBit/TSEFrame wordB1

Specifications cont’d.

Errored countsSymbol errorsCode violationFCS-errored framesRuntsJabbersOversized framesUndersized framesOOS framesLost framesIP checksum errorsIP packet-length errorsPkt payload errorsBit errorBit-error rateQoS measurementsThroughputFrame lossPacket jitterDelayOut of sequenceFrame/packet size binningMAC throughput RxIP throughput RxTCP/UDP throughput RxPayload throughput RxService disruption measurementsDefinable threshold timeRound-trip delay measurementsOne-way delay measurementsRx bytesRx MbitsRx framesRx frames per secondUtilization %Current Rx resultsMin Rx resultsAverage Rx resultsMax/peak Rx resultsRatio Rx resultsSeconds Rx resultsEvent logEvent, date, start time, stop time, duration, valueReal Time HistogramSeconds, minutes, hours, daysTimeCurrent date, current time, test-elapsed time

Graphical displays

Errors versus timeFrame loss versus timePacket jitter versus timeLatency versus timeThroughput versus time

Application testing

Walk the WindowFTP Throughput HTTP Throughput

B2B3HP-REIMS-REI, LP-BIPLP-REIInsert - SingleInsert - RateMultipleDefects/alarms generation/analysisLOSLOFRS-TIMMS-AISMS-RDIAU-LOPAU-AISHP-UNEQHP-RDIHP-TIMHP-PLMTU-LOPTU-AISTU-LOMLP-UNEQLP-RDILP-TIMLP-PLMLP-RFISDH mappingsVC4 Bulk, AU-4-4c, AU-4-16c, AU-4-64cVC12VC4VC3E4DS3E3E1SONET mappingsSTS-1, STS-3c, STS-12c, STS-48c, STS-192cVT1.5DS3DS1E1

Results

Signal categorySignal presentSignal-loss countSignal-loss secondsReceive frequencyReceive-frequency deviationReceive-frequency maximum deviationTransmit frequencyElectrical input level (STS-1 (dBdsx, dBm, volts) and STM-1e (dBnom only)BPV count (STS-1 only)BPV-error rate (STS-1 only)

Page 5: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

5

T-BERD/MTS-6000A MSAM SPECIFICATIONS

Specifications cont’d.

Regenerator/section OH categoryFAS/frame word-error countFAS/frame word-error rateLOF countOOF countB1-BIP-error countB1-BIP-error rateSeverely errored secondsOOF secondsSection trace mismatch (TIM)J0-Regenerator traceMultiplexer/line OH categoryAPS message countAPS bridge-request code (Ring)APS destination node (Ring)APS source node (Ring)APS path code (Ring)APS status (Ring)APS request code (Linear)APS K1 channel number (Linear)APS K2 channel number (Linear)APS MSP architecture (Linear)APS status (Linear)B2-BIP error countB2-BIP error rateSESUnavailable secondsAIS secondsREI countREI rateS1 Synchronization messageZ1 Byte valueHigh path (AU, VC3/4) OH categoryPointer-justification countPointer-increment countPointer-decrement countPointer-NDF countPointer valuePointer size (SS bits)LOP countB3-BIP-error countB3-BIP-error rateB3-BIP-errored secondsREI countVC-3/4 REI ratePOH SESPOH unavailable secondsSignal label (C2)J1 trace messagePath status (G1)Low path (VC3/12, TU3/12, VT1.5) categoryPointer transmittedPointer receivedPointer-justification countPointer-increment countPointer-decrease countPointer-NDF count

LOP countLOP secondsB3/V5 BIP countB3/V5 BIP-error rateREI countPointer transmittedPointer receivedSignal label (C2/V5)Signal label mismatchJ2 Lower-order trace messageJ2 Lower-order TIMLogic categoryPattern-loss countBit-error/TSE countBit-error/TSE ratePattern-slip countPattern-slip secondsPattern-loss countPattern-synchronization-loss secondsPattern-synchronization status AlarmsSignal-loss statusFrame-synchronization-loss statusPattern-synchronization-loss statusMS/Line-AISAIS (HP)AIS (LP)LOP (HP)LOP (LP)LOSOOFLOFMS/Line RDILP RDIHP RDIMS/Line-REIRegenerator trace identifier mismatch (TIM)High-path trace identifier mismatch (TIM)Low-path trace identifier mismatch (TIM)TUn loss of multiframe (n=12/3) Overhead-byte manipulation/viewing – high pathA1, A2, J0, J1, D1, D2, D3, C2, H1, H2, H3, G1, B2, K1, K2, F2, D4, D5, D6, H4, D7, D8, D9, H4, D7, D8, D9, Z3/F3, D10, D11, D12, Z4/K3, S1, Z1, M1/Z2, E2, Z5/N1SDH low-order view (AU/VT)V5, S2, N6, K4SOH and POH evaluationText decode of S and C bytes for the trace identifier. J0 display of 16-byte ASCII sequence. J1, J2 display of 16- or 64-byte ASCII sequence.Tandem connection monitoring (TCM) Analysis of the N1 and N2 bytes, monitoring/display of: AIS, ODI, RDI, OEI, REI, APId, incoming B3/computed BIP compari-son, IEC, TC-UNEQ

Performance measuresG.826 (ISM/OOS)G.828 (ISM/OOS)G.829 (ISM/OOS)M.2101T1.231T1.514K1/K2 event log Date, time, K1 value, code, channel, K2, bridge, MSP, statusEvent logEvent, date, start time, stop time, duration, valueReal-time histogramSeconds, minutes, hours, daysTimeCurrent date, current time, elapsed test time

OTN G.709Test interfaces/bit rates

OTU1 (2.7G)OTU2 (10.7G)OTU1e (11.045G)OTU2e (11.095G)

Laser type

SFPXFPXFP - Tunable

Modes of operation

TerminateMonitor

OTN layer

OTN/ODU framingODU1 in ODU2 multiplexingODU0 multiplexingODU-0 bulk BERT from an OTU-2ODU-0 1 GE Layer 2 and IPv4 traffic from an OTU-2ODU-0 bulk BERT from an OTU-1ODU-0 1 GE Layer 2 and IPv4 traffic from an OTU-1Generic mapping procedure (GMP) supportedGFP-T encapsulation of Ethernet 8B/10B PCSGFP-TCIDUPIOverhead manipulation/analysisPower levelPM/SM TTI messages Tx/RxOverhead manipulation/analysisService-disruption measurements- SD separation/debounce time setting- SD threshold time settingsPayload type (PT) label generation/displayTransfer delayFrequency offset Tx/Rx

Page 6: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

6

T-BERD/MTS-6000A MSAM SPECIFICATIONS

Specifications cont’d.

PRBS patterns2^20-1, 2^20-1 inverse2^23-1, 2^23-1 inverse2^31-1, 2^31-1 inverseProgrammable - 32 bitANSI and ITU implementationsError-insertion capabilitySingle, rateOTU error Tx/RxFASMFASSM-BIP/BEIPM-BIP/BEIFEC uncorrectableFEC correctableTCM1-6 BIPTCM1-6 BEIBit errorCodeword errors (correct/incorrect)OTU alarm Tx/RxLOFOOFLOMOOFOOMSM-IAESM-TIMSM-BDISM-BIAEPM-TIMPM-BDIFTFL Fwd signal failFTFL Fwd signal degradedFTFL Bwd signal failFTFL Bwd signal degradedTCM1-6 IAETCM1-6 TIMTCM 1-6 BDITCM1-6 BIAEODU errors Tx/RxFASMFASPM BIP/BEITCM BIP/BEIBit errorODU alarms Tx/RxLOFOOFLOMOOMAISOCILCKPM-TIMPM-BDIFTFLFTFL Fwd signal failFTFL Fwd signal degraded

FTFL Bwd signal failFTFL Bwd signal degradedTCM1-6 IAETCM1-6 TIMTCM 1-6 BDITCM1-6 BIAEOPU errors/alarms Tx/RxPT label mismatchClient lossBit errorODU mappingsBulkODU0ODU1ODU2SDH mappingsVC4 bulk, AU-4-4c, AU-4-16c, AU-4-64cVC4VC3SONET mappingsSTS-1, STS-3c, STS-12c, STS-48c, STS-192cEthernet mappings10 GE1 GE

Results

LEDSSignal presentFrame syncPattern syncLOSLOFLSSInterfaceInvalid Rx signal secondsLOS countOptical Rx level (dBm)Reference frequencyRound-trip delayRx-frequency maximum deviation (ppm)Rx-frequency (Hz)Rx-frequency deviation (ppm)Signal-loss countTx clock sourceTx-frequency maximum deviation (ppm)Tx-frequency (Hz)Tx-frequency deviation (ppm)FECUncorrected word errorsUncorrected word-error rateCorrected word errorsCorrectable word errorsCorrected word-error rateCorrectable word-error rateCorrected bit errorsCorrected bit-error rateCorrectable bit errorsCorrectable bit-error rate

FramingFrame-sync-loss secondsFrame-sync lossesOOF-seconds countFAS errorsFAS-error rateLOFLOF secondsMultiframe-sync-loss secondsOOM-seconds countMFAS errorsMFAS-error rateOTUOTU-AISOTU AIS secondsSM-IAESM-IAE secondsSM-BIP-error countsSM-BIP-error rateSM-BDI secondsSM-BDI countSM-BIAE secondsSM-BIAE countSM-BEI countSM-BEI-error rateSM-TIM countSM-TIM secondsSM-SAPISM-DAPISM-operator specificODU-AISODU-AIS secondsODU-LCKODU-LCK secondsODU-OCIODU-OCI secondsPM-BIP countPM BIP-error ratePM-BDI secondsPM-BDI countPM-BEI countPM-BEI-error ratePM-TIM secondsPM-TIM countPM-SAPIPM-DAPIPM-operator specificFTFLForward-fault typeForward-SF secondsForward-operator specificForward-operator identifierBackward fault typeBackward SF-seconds countBackward SD-seconds countBackward-operator identifierBackward-operator specific

Page 7: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

7

T-BERD/MTS-6000A MSAM SPECIFICATIONS

Specifications cont’d.

TCM 1-6IAE secondsBIP errorsBIP-error rateBDI secondsBIAE secondsBEI errorsBEI-error rateTIM secondsSAPIDAPIOperator-specificOPUPayload type mismatch secondsPayload type PayloadPattern-sync-loss secondsPattern-sync lossesTSE/bit errorsTSE/bit-error rate

Fibre ChannelLaser type

SFPXFP

Modes of operation

TerminateMonitorThru

Test interfaces/bit rates

1.0625 or 2.125 Gbps Dual-port capable4.25 Gbps Dual-port capable8.5 Gbps Dual-port capable10.519 Gbps Dual-port capable

Fibre Channel features

GeneralFlow controlLoginBuffer creditsFibre Channel loginat “F-port”at “N-port”Fibre Channel traffic generationTransmit traffic profilesConstantRampBurstyTraffic generation in Mbps and % utilizationConfigurable source and destination IDSequence IDOriginator IDResponder ID

Frame length - 28, 32, 76, 512, 1024, 1536, 2076, 2140, User-definedPacket payloadGranularity - 1 to 6.7%Fibre Channel traffic filteringRouting controlDestination identifierSource identifierData structure typeSequence countFibre Channel error insertionBit errorCRCFramed bitCode violationInsertion type - Single, rate, burstFibre Channel script (RFC-2544-like)8 G Fibre Channel-specificScrambling in FC-1/MAC layer, on total FC frameSupported IDLE and FILL WORD patterns include IDLE on Link INIT and as FILL WORD; IDLE on INIT and ARBFF on FILL WORD; ARBFF on INIT and as FILL WORD

Results

Login statusFar-end buffer-to-buffer creditsLogin statusTx/Rx ELP acceptTx/Rx ELP Ack1Tx/Rx ELP rejectTx/Rx ELP request

PDHTest interfacesE4DS3 Dual receiversE3 Dual receiversE1 balanced Dual receiversE1 unbalanced Dual receiversT1 Dual receiversInterface typeBNCBantamRJ-48

E4

Modes of operationTerminateMonitorThru (Intrusive)

Timing

Recovered from RxInternal (Stratum 3)Recoverd from external (bits/sets)

Framing

FramedUnframed

Test patterns

2^15-1* inverse2^20-1* inverse2^23-1* inverseUser-programmableRound-trip delayANSI and ITU

Mappings

E3E164 k

Anomaly/error insert/analysis

Frame errorsTSE/bit errorSingleRate

Defect/alarm insert/analysis

AISRDI/FAS distant

General

Frequency offset ±100 ppmNational bit supportPerformance measuresG.821 (OOS)G.826 (ISM/OOS)M.2100 (ISM/OOS)

Results

Signal categoryReceive frequencyReceive-frequency deviationReceive-frequency maximum deviationTransmit frequencyRound-trip delayFrame categoryFAS TSE countFAS TSE rateFAS word-error countFAS word-error rateFrame-synchronization-loss countFrame-synchronization-loss secondsLogic categoryTSE/bit-error countTSE/bit-error ratePattern slipsPattern-slip secondsPattern-synchronization-loss countPattern-synchronization-loss seconds

Page 8: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

8

T-BERD/MTS-6000A MSAM SPECIFICATIONS

Specifications cont’d.

DS3

Modes of operationTerminateMonitorThru (intrusive)

Timing

Recovered from RxInternal (Stratum 3)Recovered from external (bits/set)

Framing

M13C-BitUnframed

Test Patterns

All 1sAll 0s2^15-1* inverse2^20-1* inverse2^23-1* inverseRound-trip delayUser-progammable (3...32 bits)User byte1001100 (aka IDLE)1010 (aka BLUE)ANSI and ITU

Mappings

E1T164 k

Anomaly/error insert/analysis

BPV/code errorFrameParityC-Bit parityTSE/bit errorSingleRateMultiple

Defect/Alarm Insert/Analysis

AISRDI/FAS distantREBETS-16 AISTS-16 RDI/MFAC distant

General

Frequency offset ±100 ppmLoop codes Tx NIU, CSU, lineRx compensation - High - 0 ftRx compensation - Low - 450 ftRx compensation - Low - 900 ftService disruption

Performance measuresG.826 (ISM/OOS)G.821 M.2100M.2101T1.231T1.510

Results

Signal categoryReceive frequencyReceive-frequency deviationReceive-frequency maximum deviationTransmit frequencyBPV/code rateBPV/code countElectrical input levelRound-trip delay (ms)FrameFrame-error countFrame-error rateFrame-error secondsFrame-synchronization-loss countNear-end out-of-frame secondsFar-end out-of-frame secondsC-Bit formatRX X-BitsFEAC wordParity-error countParity-error rateParity-error secondsC-Bit parity-error countC-Bit parity-error rateC-Bit error secondsFEBEsDS2 frame-synchronization-loss countLogicBit-error/TSE countBit-error/TSE ratePattern slipsPattern-slip secondsPattern-synchronization-loss countPattern-synchronization-loss secondsPattern-synchronization status

E3

Modes of operationTerminateMonitorThru (intrusive)

Timing

Recovered from RxInternal (Stratum 3)Recovered from external (bits/set)

Framing

FramedUnframed

Test patterns

All 1sAll 0s20472^11-1* inverse2^15-1* inverse2^20-1* inverse2^23-1* inverseUser-progammable (3...32 bits)User byteRound-trip delay1:11:31:41:7ANSI and ITU

Mappings

E164k

Anomaly/error/insert/analysis

Code errorFAS errorTSE/bit errorSingleRate

Defect/alarm insert/analysis

AISRDI/FAS distant

General

Frequency offset Tx ±100 ppmTx LBO - 0 dB lossTx LBO - 6 dB lossNational bit support - On/offService disruption Performance measuresG.826 (ISM/OOS)G.821M.2100

Results

Signal categoryTransmit frequencyReceive frequencyReceive-frequency maximum deviationElectrical-input levelCode-error countCode-error rateRound-trip delay (ms)APS switch time (ms)

Page 9: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

9

T-BERD/MTS-6000A MSAM SPECIFICATIONS

Specifications cont’d.

Frame categoryFAS bit-error countFAS bit-error rateFAS word-error countFAS word-error rateFrame-synchronization-loss count8M FAS word-error rate8M FAS bit-error count8M FAS bit-error rate8M FAS word-error count8M FAS word-error rateLogic CcategoryTSE/bit-error countTSE/bit-error ratePattern slipsPattern-slip secondsPattern-synchronization-loss countPattern-synchronization-loss secondsPattern-synchronization status

E1Modes of operationTerminateMonitorThru (intrusive)TimingRecovered from RxInternal (Stratum 3)Recovered from external (bits/set)FramingUnframedPCM30PCM30CPCM31PCM31CTest patternsAll 1sAll 0s2^15-1* inverse2^20-1* inverse2^23-1* inverseQRSSUser-progammable (32 bits)Round-trip Delay1:11:31:41:7ANSI and ITU

Mappings64k

Anomaly/error insert/analysisCode errorFAS errorMFAS errorTSE/bit errorSingleMultipleRate

Defect/alarm insert/analysis

AISREBETS-16 AISTS-16 RDI/MFAS distant

General

Frequency offset Tx ±100 ppmService disruption Performance measuresG.826 (ISM/OOS)G.821G.829 (ISM/OOS)M.2100

Results

Signal category2M receive frequency2M reference frequency2M receive-frequency deviation2M receive-frequency maximum deviation2M transmit frequencyElectrical-input levelCode-error countCode-error rateRound-trip delay (ms)Timing slipsFrame slipsAPS switch timeLogic categoryTSE/bit-error countTSE/bit-error ratePattern slipsPattern-slip secondsPattern-synchronization-loss countPattern-synchronization statusAlarm categoryFAS/frame synchronizationMFAS synchronizationCRC synchronizationAISRDIPower-loss count2M alarmFrame categoryFAS bit-error countFAS bit-error rateFAS word-error countFAS word-error rateNonframe-alignment wordMFAS word-error countMFAS word-error rateTime-slot Rx byteCRC-error countCRC-error rateCRC-synchronization-loss countFAS-synchronization-loss countMFAS-synchronization-loss countRemote-end block error (REBE)

T1

Modes of operationTerminateMonitorThru (intrusive)

Timing

Recovered from RxInternal (Stratum 3)Recovered from external (bits/set)

Framing

UnframedSFESFSLC-96

Test patterns

63511511 QRSS2047 QRSS2047All 1sAll 0s2^15-1* inverse2^20-1* inverse2^23-1* inverseQRSSUser-progammable (3...32 bits)User byteBridged tapMultiPatRound-trip delay1:11:31:41:72 in 83 in 24MIN/MAXT1 DALY55 OCTETT1-2/96T1-3/54T1-4/120T1-5/53

Mappings

64 k56 k

Anomaly/error insert/analysis

Frame errorsBPV errorsTSE/bit errorSingleRateMultiple

Page 10: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

10

T-BERD/MTS-6000A MSAM SPECIFICATIONS

Specifications cont’d.

Defect/alarm insert analysis

AISREBE

General

Frequency offset Tx ±100 ppmPerformance measuresG.826 (ISM/OOS)G.828 (ISM/OOS)G.829 (ISM/OOS)M.2100T1.231Tx LBO - 0 dB lossTx LBO - 7.5 dB lossTx LBO - 15 dB lossTx LBO - 22.5 dB lossService disruption

Loop codes

Loop-code Tx - NIULoop-code Tx - CSULoop-code emulation - NIULoop-code emulation - CSUHDSL loop-code TxCO-to-customer directionCustomer-to-CO directionUser-defined loop-code support

Results

Signal categoryReceive frequencyReference frequencyReceive-frequency deviationReceive-frequency maximum deviationTransmit frequencySimplex currentReceive level (Vp)Receive level (dBdsx)Receive level (dBm)BPV-error countBPV-error rateFrame-slip countSignal-loss countSignal-loss secondsRound-trip delay (ms)Timing slipsFrame slipsAPS switch timeFrame categoryFrame-error countFrame-error rateFrame-error secondsFrame-loss countFrame-loss secondsSeverely errored secondsCRC-error countCRC-error rateCRC-errored secondsCRC-severely errored seconds

Logic categoryBit-error/TSE countBit-error/TSE rateBit-error/TSE secondsPattern slipsPattern-slip secondsPattern-synchronization-loss countPattern-synchronization-loss secondsChannelDSO channel-payload viewABCD bit-signaling view

CPRITest interfaces/bit rates

CPRI 3.1G optical Tx/Rx

Laser type

SFPTuned SFP

Modes of operation

TerminateMonitor

CPRI features

Optical/electrical power levelFrequency offset Tx/RxRound-trip delay measurementRTD measurement accuracyPRBS patterns2^23-1, 2^23-1 inverseANSI and ITU implementationsAnomaly/errors generationBitInsert - SingleInsert - Rate

Results

Signal categorySignal lossesSignal-loss secondsReceive frequencyReceive-frequency deviationReceive-frequency maximum deviationTransmit frequencyTransmit-frequency deviation (Hz)Transmit-frequency deviation (ppm)Transmit-frequency maximum deviation (ppm)Error statsPattern-sync lossesPattern-sync-loss secondsBit-error rateBit errorsErrored secondsError-free secondsError-free seconds, %Total bits received

Jitter O.172General features

Generate and measure jitteron electrical interfaces (DS1, E1, DS3, E3, E4, STM1e)Automatic measurement sequences- Maximum tolerable jitter (MTJ)- Measure intrinsic jitter- Jitter transfer function (JTF)Support different measurement bands- High band- Wide band- Extended band- Set user-definable bandSelect common jitter maskCreate user-definable masks

Results

Jitter results per measurement bandCurrent peak-to-peak jitter [UI]- Peak-to-peak jitter [UI]- Positive peak jitter [UI]- Negative peak jitter [UI]Maximum peak-to-peak jitter [UI]- Peak peak jitter [UI]- Positive peak jitter [UI]- Negative peak jitter [UI]Phase hitsPercentage of maskRMS jitter [UI]Jitter graphs

NextGen SONET/SDHTest interfaces/bit rates

OC-3OC-12STM-4OC-48STM-16OC-192STM-64

Laser type

SFPXFPXFP - Tunable

Modes of operation

TerminateMonitor

Timing

Recovered from RxInternal (Stratum 3)Recovered from external (bits/set)Recovered from 10 MHz clock

Page 11: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

11

T-BERD/MTS-6000A MSAM SPECIFICATIONS

Specifications cont’d.

SONET/SDH features

VCAT - High orderVCAT - Low orderLCAS emulation/analysisDifferential delay measurementMaximum VCAT group sizeGFP-FEthernet clientMaximum Ethernet client size 1 GBRound-trip delay measurementRTD measurement accuracyPRBS patterns215-1, 215-1 inverse2^20-1, 2^20-1 inverse2^23-1, 2^23-1 inverse2^31-1, 2^31-1 inverseProgrammable - 32 bitANSI and ITU implementationsAnomoly/errors generationGFP-Idle-frame errorGFP-Short-frame errorGFP-Core-header errorGFP-Type-header errorGFP-EXI errorGFP-PFI errorGFP-PLE errorFCSB1B2B3HP-REIMS-REI, LP-BIPLP-REIInsert - SingleInsert - RateDefects/alarms generation/analysisGFP-CSF alarmGFP-LFD alarmLOM2 alarmLOSLOFRS-TIMMS-AISMS-RDIAU-LOPAU-AISHP-UNEQHP-RDIHP-TIMHP-PLMTU-LOPTU-AISTU-LOMLO-UNEQLP-RDILP-TIMLP-PLMLP-RFI

SDH mappingsVC4 Bulk, AU-4-4c, AU-4-16c, AU-4-64cVC12VC4VC3GFP-FEthernetSONET mappingsSTS-1, STS-3c, STS-12c, STS-48c, STS-192cVT1.5GFP-FEthernet

Results

Signal categorySignal presentSignal-loss countSignal-loss secondsReceive frequencyReceive-frequency deviationReceive-frequency maximum deviationTransmit frequencyRegenerator/section OH categoryFAS/frame word-error countFAS/frame word-error rateLOF countOOF countB1-BIP-error countB1-BIP-error rateSeverely errored secondsOOF secondsSection trace mismatch (TIM)J0-Regenerator trace

Multiplexer/line OH categoryAPS message countAPS bridge request code (Ring)APS destination node (Ring)APS source node (Ring)APS path code (Ring)APS status (Ring)APS request code (Linear)APS K1 channel number (Linear)APS K2 channel number (Linear)APS MSP architecture (Linear),APS status (Linear)B2-BIP-error countB2-BIP-error rateSESUnavailable secondsAIS secondsREI countREI rateS1 Synchronization messageZ1 Byte value

High path (AU, VC3/4) OH categoryPointer-justification countPointer-increment countPointer-decrement countPointer-NDF countPointer valuePointer size (SS bits)LOP countB3 BIP-error countB3 BIP-error rateB3 BIP-errored secondsREI countVC-3/4 REI ratePOH SESPOH unavailable secondsSignal label (C2)J1 trace messagePath status (G1)

Low path (VC3/12, TU3/12, VT1.5) categoryPointer transmittedPointer receivedPointer-just countPointer-increment countPointer-decrement countPointer-NDF countLOP countLOP secondsB3/V5 BIP countB3/V5 BIP-error rateREI countPointer transmittedPointer receivedSignal label (C2/V5)Signal-label mismatchJ2-Lower-order trace messageJ2 Lower-order TIM

Logic categoryPattern-loss countBit-error/TSE countBit-error/TSE ratePattern-slip countPattern-slip secondsPattern-loss countPattern-synchronization-loss secondsPattern-synchronization status

AlarmsSignal-loss statusFrame-synchronization-loss statusPattern-synchronization-loss statusMS/Line-AISAIS (HP)AIS (LP)LOP (HP)LOP (LP)LOSOOFLOFMS/Line RDI

Page 12: T-BERD/MTS-6000A MSAM Specifications - · PDF fileT-BERD®/MTS-6000A MSAM Specifications. Ethernet. Test interfaces/bit rates. ... IP packet generator IP. ... Automatic. Local Far

T-BERD/MTS-6000A MSAM SPECIFICATIONS

Product specifications and descriptions in this document subject to change without notice. © 2011 JDS Uniphase Corporation 30173009 000 1011 6000MSAMSPECS.DS.TFS.TM.AE October 2011

Test & Measurement Regional Sales

NORTH AMERICATEL: 1 866 228 3762FAX: +1 301 353 9216

LATIN AMERICATEL: +1 954 688 5660FAX: +1 954 345 4668

ASIA PACIFICTEL: +852 2892 0990FAX: +852 2892 0770

EMEATEL: +49 7121 86 2222FAX: +49 7121 86 1222

WEBSITE: www.jdsu.com/test

Specifications cont’d.

LP RDIHP RDIMS/Line-REIRegenerator trace identifier mismatch (TIM)High path trace identifier mismatch (TIM)Low path trace identifier mismatch (TIM)TUn loss of multiframe (n=12/3)

Overhead byte manipulation/viewing – High pathA1, A2, J0, J1, D1, D2, D3, C2, H1, H2, H3, G1, B2, K1, K2, F2, D4, D5, D6, H4, D7, D8, D9, H4, D7, D8, D9, Z3/F3, D10, D11, D12, Z4/K3, S1, Z1, M1/Z2, E2, Z5/N1.

SDH Lower-order view (AU/VT)V5, S2, N6, K4

SOH and POH evaluationText decode of S and C bytes for the trace identifier. J0 display of 16 byte ASCII sequence. J1 and J2 display of 16- or 64-byte ASCII sequence.

Tandem connection monitoring (TCM) Analysis of the N1 and N2 bytes, monitoring/display of: AIS, ODI, RDI, OEI, REI, APId, incoming B3/computed BIP comparison, IEC, TC-UNEQ

K1/K2 event log Date, time, K1 value, code,channel, K2, bridge, MSP, status

Event logEvent, date, start time, stop time, duration, value

Real-time histogramSeconds, minutes, hours, days

TimeCurrent date, current time, elapsed test time

Services VoIP testing

10/100/1000 M electrical Ethernet interfaces1 GE optical Ethernet interface10 GE optical Ethernet interfaceSIP, Cisco SCCP, and H.323 Fast ConnectSIP parametersDial by phone/URL/e-mailNortel and Huawei SIP emulationProxy login and proxyless operationSCCP parametersSelectable Cisco phone emulation supporting at least 15 modelsConfigurable device nameH.323 parameters H.323 IDBearer capability including unrestricted digital, speech, and3.1 K audioConfigurable calling and called-party number plans and number types

Static, auto-discoverable, and no-gatekeeper operationConfigurable local and gatekeeper RAS port and Call Control portConfigurable time zoneConfigurable RTP port rangeGeneral parametersAuto answer on/offCodecs:

- G.711 A Law- G.711 U Law- G.723 5.3 K- G.723 6.3 K- G.729A- G.726- G.722

Configurable Call Manager portSelectable silence supressionConfigurable jitter buffer and speech-per-frame parametersACR or G.107 MOS scoringConfigurable jitter, loss, delay, and content thresholds pass/failMean Opinion Score results (MOS)Graphical summary results including Ethernet, transport and contentTransaction log including call log and protocol signaling

Triple-play automated test script

10/100/100 0M electrical Ethernet interfaces1 GE optical Ethernet interface10 GE optical Ethernet interface- More than 11,000 simulated calls with configurable codec

and sampling rate- Configurable voice call or tone with configurable silence

supression, sampling rate, and jitter buffer- Up to 250 simulated SDTV channels with configurable

frame size and MPEG-2/4 compression- Up to 52 simulated HDTV channels with configurable frame

size and MPEG-2/4 compression- Two configurable data streams with individual constant or

ramp traffic and configurable frame sizes including random frames

IPTV

10/100/1000 M electrical Ethernet interfaces1 GE optical Ethernet interface10 GE optical Ethernet interface- Single- and multiple-program transport stream (SPTS/

MPTS) formats- Video explorer capable of detecting 512 SPTSs and 32 MPTSs

and a video analyzer that supports 16 SPTSs and 1 MPTS- Supported measurements include bandwidth utilization,

packet loss, packet jitter, PCR jitter, continuity-error bit and error-bit indicator

- TR 101 290 priority 1 errors, such as program identification (PID), program association table (PAT), and program map table (PMT)

- Loss-distance and period errors per RFC 3357, results per-transport stream and per PID

- Measure ICC latency and R-UDP latency- Microsoft Television (MSTV) Support- Internet Group Management Protocol (IGMP) support

Primary rate ISDN

Test access - T1TE emulationNT emulationD-Channel signaling decodesCall control - NationalCall control - 5ESSCall control - NI-1D-Channel rate - 64 kD-Channel rate - 56 kCall type - DataCall type - VoiceCall type - 3.1 k audioChannel number - 1 to 24D-Channel rate - 56 k

Signaling - place/receive call

Test access - T1E&M signalingLoop-start signalingGround-start signalingAudio drop/insertSignaling bitsPlace callReceive callMF digitsDTMF digitsEvent logVF tone insertion

Fractional T1/E1

Test access - T1Fractional T1 - n x 64 kFractional T1 - n x 56 kContiguous channelsNoncontiguous channelsV.54 Loop-code support

Voice frequency

Test access - T1Listed to an audio callInsert VF tones 404, 1004, 1804, 2713, and 2804 HzUser frequencyQuiet toneHolding toneThree toneFrequency sweepImpulse noiseRx frequencyLevel (dBm)DC offset mV