TRACK TECHNICAL DETAILS and FITTING INSTRUCTIONS

19mm

Max 120cm Max 8cm

30mm

Top fix or face fix

S Y S T E M 3 0 B E N D A B L E

S Y S T E M 3 0 S T R A I G H T

B R A C K E T S PA C I N G

Max 60cmMax 60cm

Top fix or face fix with brackets either side of every bend, max spacing 60cm

19mm

30mm

* A bracket is required either side of every bend

B R A C K E T S PA C I N G

* Two brackets are required at the track ends

1

Sales: 0845 465 0101e-mail: info@polesandblinds.com

www.polesandblinds.com

S Y S T E M 3 0 S T R A I G H T

S Y S T E M 3 0 B E N D A B L E

TOP FIXING

Fit track directly to ceiling or top board, using pre-drilled holes

For additional support simply drill more holes into the track using a 4mm drill bit (not supplied)

No brackets required

Fit track directly to ceiling or top board, using pre-drilled holes

No brackets required

When top fixing bendable track, DO NOT over tighten screws as this can deform the track and cause the gliders to jam

TOP FIXING

IMPORTANT

FACE FIX BRACKETS FOR SYSTEM 30

FACE FIX BRACKETS FOR SYSTEM 30

Use pre-drilled holes

2

Front

Back

Front

Back

60mm

42mm 45mm

58mm

Cover

60mm

42mm

58mm

Cover

45mm

Magnet

Magnet

Magnet

Magnet

Magnet

Cover plate

S YS T E M 3 0 S T R A I G H T J O I N E R F I N I A L S

S YS T E M 3 0 B E N D A B L E J O I N E R

Ensure magnet is at the front of the track so that the cover plate will locate correctly

The finials below are for System 30 straight and bendable only

Remove part of the inner plastic section to create space to insert the joiner

Ensure magnet is at the front of the track so that the cover plate will locate correctly

79mm

60mm

33mm

33mm

33mm

20mm

84mm

Square Barrel finial

Collar finial

Cap finial

Ball finial

43mm

Suitable for use with top fix

NOT Suitable for use with topfix

3

C U R TA I N H E A D I N G SWe recommend curtain headings should be underslung for all three tracks to ensure the best operation of the curtains

10mm

B E N D I N G S Y S T E M 3 0

Bend B

Trim here

Trim here

Bend B

Bend CBend C

Bend A Bend A

Window centre

Joiner

The track can be bent around a curved object with a radius of no less than 100mm. We recommend covering the track with a tea towel to prevent scratches.

Bend track until kerfs touch. Do not bend any further

Track lengths of 150cm - 300cm are supplied in 1 piece.Track lengths of 360cm - 600cm are supplied in 2 pieces.Track lengths of 720cm - 900cm are supplied in 3 pieces.

It’s easy to achieve:

FORWARD BENDS REVERSE BENDS CONTINUOUS BENDS

Easy to bend on site at point of installation. No more measuring up and hoping. No transporting awkward and delicate bent tracks

4

Radius 150

Radius 150

Trim off excess track at the track ends4

Bracket spacing - see front page5

Bend from the centre working outwards. Bend A, then B, then C, one side then A-C on the other side

3

B E N D I N G TO F I T A B AY

Identify front and back of track

Insert joiner, pushing the plastic filler down the track and tighten screws2

1

Front

Back

Diagram shows track joiner attaching two track lengths at the window centre

Obect

radiu

s

100mm

Bend towards the straight end NOT LIKE THIS

B E N D I N G S YS T E M 3 0

This method causes internal stress in the track which can cause the gliders to jam

DO NOT try to bend towards another bendOpen end

Open end

Curved object

Curvedobject

Bend track until kerfs touch. Do not bend any further

J O I N I N G A L L T R A C K S

Trim ends and cover with end caps/finials

Uncut factory ends

Uncut factory ends Uncut factory ends

With careful installation gliders will smoothly pass over the track joins. There is no limit to maximum track length

Join together factory cut ends and trim off the excess at track ends only

Place a support bracket as close as possible to the join

Ensure the joins are butted together tightly before tightening lock screws

5

Trim off excess track at the track ends

Bracket spacing - see front page

1

2

3

Sales: 0845 465 0101

e-mail: info@polesandblinds.com

www.polesandblinds.com