sys_rec_e

8/13/2019 sys_rec_e

1/4

318 Chapter 12

Setting and Using the Control and Management Functions

System Recovery

System Recovery

By executing system recovery, you can return the system of the E5070B/E5071B (the

Windows operating system and the firmware) to the factory state (at the time of

purchase*1).

Notes on executing system recovery

Executing system recovery causes the following:

In addition to the Windows operating system and the firmware, the following settings

of the E5070B/E5071B are returned to the factory state.

Network setting

GPIB setting

Printer setting

The driver for the supported printer installed after purchase is deleted.

You need to execute initial registration again.

Files you created using the save function (files in the D drive) are not affected, but we

recommend backing them up before executing system recovery for precautionary

purposes. For more information on backup, refer to Making Backup Files on page 418.

*1.If the hard disk failed and has been replaced after purchase, the state when the replacement

was performed is recovered.
http://-/?-http://-/?-

8/13/2019 sys_rec_e

2/4

Chapter 12 319


System Recovery

g

Functions

Procedure to execute system recovery

NOTE You need the keyboard for this operation.

Step 1. Shut down the E5070B/E5071B.

Step 2. Connect the keyboard to the E5070B/E5071B.

Step 3. Insert the disk for the system recovery into the floppy disk drive of the E5070B/E5071B.

Step 4. Press the standby switch of the E5070B/E5071B to turn it on.

Step 5. When the screen as shown in the figure below appears, press and hold of the

keyboard until this screen disappears.

NOTE After several seconds, the next screen appears automatically even if you do not press any

key, so do not miss it.

If the above message does not appear, the instrument is at fault; contact your local Agilent

customer center listed at the end of this manual or distributor.

8/13/2019 sys_rec_e

3/4

320 Chapter 12


System Recovery

Step 6. The following screen appears. Check that Floppy is selected (highlighted) (if Floppy is not

selected, select it with of the keyboard), and press of the keyboard.

Step 7. The message as shown below appears. Press of the keyboard. If you want to cancel the

system recovery, press here.

Agilent Technologies System Utilities

Recovery & Backup Options (for the E5070/71B)

Choose One of the following:

_________________________________________________________________

1. Recover Factory Backup Image

2. Exit

_________________________________________________________________

Enter a Choice: _

NOTE If the above message does not appear, the instrument or the disk for the system recovery is

at fault; contact your local Agilent customer center listed at the end of this manual or

distributor.

8/13/2019 sys_rec_e

4/4

Chapter 12 321


System Recovery

g

Functions

Step 8. The message as shown below appears. Press of the keyboard. If you want to cancel the

system recovery, press here.

You chose to Restore your system by installing the original factory

installed OS and system software.

WARNING: Press C to Continue only if you are sure that you wantto proceed. The C: Drive will be completely overwritten with no

chance of recovering any data. Use Option 1 to recover the system

from a serious malfunction caused by corrupted or inadvertently

deleted files on the system's primary C: partition.

Press C to Continue or E to Exit: _

Step 9. The message as shown below appears. Press of the keyboard to start the system

recovery. If you want to cancel the system recovery, press here.

CAUTION! Interrupting this process may leave the system in an

unstable state. Allow the software to complete the

backup and recovery process. This may take up to 20

minutes depending on the system configuration.

Press C to Continue or E to Exit: _

CAUTION Never turn off the power during the system recovery because doing so may cause

serious damage to the E5070B/E5071B.

Step 10. The system recovery will be complete in about 5 minutes. When the system recovery is

complete, the message as shown below appears. Press , , and of the

keyboard at the same time to restart.

Remove the disk and Press CLT+ALT+DEL to restart your

system.

NOTE If the above message does not appear, the instrument is at fault; contact your local Agilent

customer center listed at the end of this manual or distributor.

Step 11. After restart, the screen for initial registration appears. Execute initial registration. For

information on the execution procedure, refer to Installation/Quick Start Guide.

Step 12. For the E5070B/E5071B equipped with the Option 016 touch screen, execute the

calibration of the touch screen. For information on the execution procedure, refer to

Calibration of the Touch Screen on page 322.
http://-/?-http://-/?-

Documents

sys_rec_e