Embed Size (px)
DESCRIPTION
Istructions
Citation preview
This Castle meets the �ammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any �ame source. The application of any foreign substance to the Castle fabric may render the �ame resistant properties ine�ective.
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THE SWEET LILYTM CASTLE FABRIC.
WARNING:
Adult assembly required.
Thanks for purchasing the SWEET LILYTM Castle. Please read and retain these instructions.
AGES 3+
68779
For video assembly instructions, please visit
www.mysweetlilycastle.com
Includes:
41x Connectors
30x White Frame Tubes
2 Fabric Castle Covers
Also includes:1 princess dress (fits sizes 3T to 6X)1 tiara1 wand1 frog prince
1
BACK FRONT
4x Grey Plastic Tubes
26x Pink Frame TubesFront side Back side
2 x #1 2 x #1
1x Green Plastic Tube
2 x Grey Plastic Connectors
4 x front bottom connectors (red)
4 x back corner connectors (red)
11 x straight connectors (white)
6 x tee connectors (yellow)
4 x roof corner X connectors (green)
4 x hip corner top connectors (blue)
4 x roof corner Y connectors (orange)
2 x #10
2 x #9
2 x #8
2 x #7
2 x #6
2 x #5
12 x #4
2 x #3
2 x #2
4 x hip corner base connectors (blue)
2 x #2
10 x #3
2 x #4
2 x #5
2 x #6
2 x #7
2 x #8
2 x #9
Front FrameAssembly:
Assemble Front frame as shown.This will be done in Three steps:
1. Start with the base—just like building a normal house.
2. Build the castle walls—add all the vertical tubes with the connectors on the top. Add tubes for the top of the walls.
3. Build the roof—add the tubes and connectors, as shown. The roof will create a four-sided peak.
Parts required for this step:- All connectors- All white frame tubes
Make sure connectors are pushed into the tubes as far as they will go.
2
#4
#4
#4#4
#4
#4
#4
#4#4
#4
#4
#4
#8
#7
#7
#9
#9#10#6 #3#6 #5
#5
#1
#2#3
#2
#1
#8
#10
Assemble Front frame as shown.
3. Build the roof—add the tubes and connectors, as shown. The roof will create a four-sided peak.
BackFrameAssembly:
Assemble Back frame as shown.
Parts required for this step:- Remaining connectors- All pink frame tubes
Make sure connectors are pushed into the tubes as far as they will go.
3
This will be done in Three steps:
1. Start with the base—just like building a normal house.
2. Build the castle walls—add all the vertical tubes with the connectors on the top. Add tubes for the top of the walls.
3. Build the roof—add the tubes and connectors, as shown. The roof will create a four-sided peak.
#1
#1#2
#2
#3
#3
#3#3
#3 #3
#3
#3
#3#3
#5#5 #4
#4
#9
#7
#6
#6#7#8
#8#9
CastleBackCover:
4
Parts required for this step:- Completed Frame (pink)
- SWEET LILY Castle Back
SWEET LILY Castle Back Cover1. Assemble pink frame as shown on page 3.
2. Remove the SWEET LILY Castle back cover
from the bag marked “Back.”
3. Completely unzip the cover all the way
around.
4. Separate the inside and outside walls
by pulling apart the hook-and-loop
fasteners (don’t forget
the windows!).
6. Line up the frame on the red seam as shown.5. Lay the cover out so both the rectangular
red seam and lavender wall face up.
BACK
5
7. Lift the inside wall up and attach it to the frame
with the hook-and-loop fasteners.
8. Pull out any excess cover from the outside corners of the frame base to make a snug pocket.
Pull the cover over the closed end of the frame and across the top of the roof (you may need a helper).
The zipper strip should align with the frame.
17xfasteners
Make sure the bottoms of the
strips line up with the bottoms of
the pads.
6
9. Zip up the cover around the frame. Press the three hook-and-loop fasteners along inside the cover at
the top of the frame to keep the roof from sagging.
10. Align and fasten the hook-and-loop fastener around
both windows.
The back of the castle is now
complete. Let’s do the front!
CastleFrontCover:
Parts required for this step:- Completed Frame (white) - SWEET LILY Castle Front
SWEET LILY Castle Front Cover1. Assemble white frame as shown on page 2.
2. Remove the SWEET LILY Castle front cover
from the bag marked “Front”.
3. Completely unzip the cover all
the way around.
5. Separate the inside and outside walls
by pulling apart the hook-and-loop
fasteners.
6. Lay the cover so the rectangular red seam
is exposed. The pink inside wall is over the
the printed floor. The doors should
be tucked under the floor.
7
FRONT
4. Unzip the front doors.
6. Line up the frame on the red seam, as shown.
7. Lift the inside wall up and attach it to the frame
with the hook-and-loop fasteners.
16x fasteners
Make sure the bottoms of the
strips line up with the bottoms
of the pads.
8
8. Pull out any excess cover from the outside corners of the frame base to make a snug pocket. Pull the cover with the doors over the closed end of the frame and across the roof (you may need a helper). The zipper strip should align with the frame.
9. Zip up cover around the frame. Press the three hook-and-loop fasteners along inside the cover at the top of the frame to keep the roof from sagging.
9
10
10. Fasten the two wide hook-and-loop fasteners around the vertical tubes on both sides of the door. Zip up the door.
11. Unhook the fasteners in the roof turret. Raise the turret by bending the green plastic tube to fit inside. The flat end fits in the middle of the center disk at the bottom and the cone-shaped end faces up.
The front of the
castle is now
complete. Let’s build
the towers!
Questions? Call 1-800-PLAYSKL
Product and colors may vary. © 2008 Hasbro. All Rights Reserved.TM & ® denote U.S. Trademarks.© 2008 Worlds Apart Ltd. All rights Reserved. PN# 0000000000
TowerAssembly:
Storage:
For the entire Dream TownTM Collection
1. Take two grey tubes and one connector. Insert a tube into each end of connector.
2. Open the hook-and-eye fasteners in the tower. Insert one end of the tube into the tower up to the the point. Fit the bottom of the plastic tube into the middle of the center disk in the tower floor.
3. Reclose the tower and attach it to the hook-and-loop fasteners at the front corners of the castle. The windows face out. Repeat Steps 1,2 and 3 for the second tower.
Parts required for this step:- 2 Tower covers- 4 Grey plastic tubes- 2 Grey plastic connectors
