SVAB GRIP L8technical information

Revision C

Revision table

Revision Description Page Date Signature Authorized

A First edition. 121213 FRJA FRER

B

Added data to SMG toggle switch. Added underlaying joystick graphics to front plate positions. Added data to cables.Added info/feature about “dead man” usage.Added info about pos. 3 back side not being pluggable. Also add-ed info about the possibility to use a toggle swith in position 3.

1810, 2481524

130319 FRJA FRER

C Changed graphics according to new graphic profile. - 130405 FRJA FRER

© 2013 SVAB Hydraulik AB. All rights reserved.

SVAB accepts no responsibility for possible errors in catalogs, brochures and other printed material. SVAB reserves the right to alter its products without prior notice. This also applies to products already or-dered provided that such alterations can be made without affecting agreed specifications. All trademarks in this material are properties of their respective owners.

Contents Page

1. INTRODUCTION ................................................................................................................... 6

2. L8 - GENERAL TECHNICAL DATA ........................................................................................... 72.1 CABLES ....................................................................................................................8

3. HOLE PATTERN LAYOUT ..................................................................................................... 103.1 FRONT PLATE HOLE PATTERN LAYOUT ...........................................................................103.2 BACK SIDE HOLE PATTERN LAYOUT ..............................................................................12

4. PROPORTIONAL THUMBWHEEL .......................................................................................... 13

5. PUSHBUTTONS ................................................................................................................... 15

6. TOGGLE SWITCHES, LEDs AND MINITRIM .......................................................................... 17

7. MOUNTINGS ....................................................................................................................... 22

8. PRODUCT CONFIGURATION CODE ...................................................................................... 248.1 L8 JOYSTICK GRIP POSITIONS ....................................................................................24

9. ACCESSORIES .................................................................................................................... 269.1 ADAPTER BALL KIT FOR STANDARD MOUNTING L8 .........................................................279.2 BELLOW WASHERS ....................................................................................................289.3 BELLOW ADAPTERS FOR STANDARD BELLOW WASHER ...................................................29

6 INTRODUCTION

1. INTRODUCTION

The SVAB Grip L8 is designed as an ergonomic joystick grip for earth-moving machinery. It can be fitted with up to three proportional thumbwheels which can be controlled by the thumb or the index finger. It can also be equipped with up to 9 pushbuttons (7 with 2 proportional thumbwheels).

Available with direct analog/digital outputs and also with SVAB internal CAN bus connection where it thereby can interact directly with other CAN bus connected units in SVAB systems.

It is possible to combine both analog/digital and CAN bus output in the same grip.

The L8 grip comes in both left and right hand design and in dark gray or black coloring.

GENERAL TECHNICAL DATA 7

2. L8 - GENERAL TECHNICAL DATA

SVAB GRIPL8 DIMENSIONS (in millimeters) AND TECHNICAL DATA

Info:

The development of the SVAB Grip L8 joystick grip comes from long experience and ergonomic stud-ies which has given the L8 great comfort and functionality.

Features:

• Ergonomically designed.

• Rubberized sur-face.

• Room for thumb-wheels and push buttons on both the front and back.

• Easily mounted on market joy-stick bases. Both hydraulic and electric.

• Adapted for a large variety of thumbwheels, pushbuttons and toggle switches.

165

12585

Operating temperature range -40°C to 70°C

Storage temperature -40°C to 85°C

Case material PC/ABS

Coating Soft touch

Mass Up to 340 g

Degree of protection IP 40

Electrical interface options Analog/Digital or CAN-bus

Front panel thickness 3mm

8 GENERAL TECHNICAL DATA

2.1 CABLES

SVAB Grip L8 cable is available for both analog/digital signals as well as for CAN bus communication. It is also possible to combine analog/digital signals and CAN bus communication in the same joystick grip.

ANALOG/ DIGITAL CABLE TECHNICAL DATA

Info:

You can choose wheth-er L8 is to be supplied with or without analog/digital cables.

Analog/digital cable is delivered without con-tacting. Consult a SVAB sales representative if contacting is required.

Materials

Conductor Tin-coated copper

Primary insulation Radiation-crosslinked, extruded polyalkene

Jacket Radiation-crosslinked modified PVF2. Thickness: .003 ± .001 in.

Wire size (AWG) 24

GENERAL TECHNICAL DATA 9

CAN CABLE DIMENSIONS (in millimeters)

Info:

When choosing CAN based communication a fully as-sembled CAN cable is always included.

L8 CAN cable has 4-pin M8 male connectors.

The L8 CAN cable uses PUR cable. This cable is intend-ed as a bonding and connection cable for high mechani-cal loads in industrial operation with abrasive stress. The PUR cable is fit for environments where there is a high demand of protection from chemical solvents and oil.

Visible cable’s length (including contact) is 90 cm.

900

M8x1

Face view

10 HOLE PATTERN LAYOUT

3. HOLE PATTERN LAYOUT

The hole pattern layout shows where the thumbwheels, push buttons and toggle switches can be placed on the front plate of the joystick grip, and the diameter of holes for pushbuttons and toggle switches.

HOLE DIAMETER

A Ø15,2

B Ø12

C Ø6,5

D Ø4,4

In chapter “3.1 FRONT PLATE HOLE PATTERN LAYOUT” below, only the right front plate is shown. The same hole pattern layout applies to both right and left joystick grip with the difference that the left front plate is mirrored according to position numbering:

FRONT PLATE LEFT FRONT PLATE RIGHT

3

6 45

12 1

4 65

32

3.1 FRONT PLATE HOLE PATTERN LAYOUT

10 (right) 11 (right) 12 (right) 13 (right) 14 (right) 15 (right)

1 2 1 2 3A1 2

4A 5A

1 2

5B4A 6A

3A 1 2

4A 5A 6A

3A 1 2 3A

6A

16 (right) 18 (right) 19 (right) 20 (right) 21 (right) 22 (right)

5A

2A

6A

3A

4

1 1 2

5C4A 6A

3A 1 2

4B 5B 6A

3A 1 2

4 5

1 2

4 5

3A 1 2

4 5

3A

6A

HOLE PATTERN LAYOUT 11

23 (right) 24 (right) 25 (right) 32 (right) 33 (right) 35 (right)

3A

4

1

5

2 3A

6A4

1

5

2 1 2

4 5

3A

6B

1A 2A 1A 2A 3A 1A

4A

2A

5A

3A

36 (right) 1A (right) 26 (right) 27 (right) 28 (right) 37 (right)

1A

4A

2A

5A

3A

6A

1 2

4A 5A

3A 1 2

4 5

3B 3B

4

1

5

2 3A

4

1 1 2 3A

5B

1D (right) 39 (right) 1G (right) 1F (right) 1H (right) 1I (right)

3A

6C4

1

5

2 1 2

4B

3A 1 2

4A 6A

3A

7 D

5B

1 2

4A 5A

3A

6C

1 2

4A

3A

5B

1 2

5A

3A

4B

1J (right) 1K (right) 1L (right) 1N (right) 1P (right)

1A 2A 3A

5 D

1 2

4A

3A

5B 6 D

1 2

4 5

3A

6 D

2A

6A

3A

5B4

1 1 2

4B 5A 6A

3A

12 HOLE PATTERN LAYOUT

3.2 BACK SIDE HOLE PATTERN LAYOUT

The back of the L8 grip always has the same hole pattern layout. When the holes aren’t used by thumb-wheel and pushbuttons, the holes are plugged.

On the L8 joystick grip’s back side only thumbwheels (position 4) and pushbuttons (positions 1, 2 and 3) can be positioned.

BACK SIDE LEFT

BACK SIDE RIGHT

1

2

3

4

1

2

3

4

PROPORTINAL THUMBWHEEL 13

4. PROPORTIONAL THUMBWHEEL

Thumbwheel SVAB HECR is our internally developed spring-loaded thumbwheel. The thumbwheel has a short rotational angle and therefore need only a relatively small influence of the thumb or finger to get full effect.

THUMBWHEEL SVAB HECR TECHNICAL DATA

Features:

• Analog and vari-able.

• Flat collar for flat surfaces. Round collar for rounder surfaces.

• Dual analog signals.

Electrical Characteristics

Supply Voltage (Vs) 4.5 VDC min.5.0 VDC typ.5.5 VDC max.

Supply Current 14 mA typ.20 mA max.

Over/Under Voltage Protection -8.5 VDC min.8.5 VDC max.

Output Voltage (Signal 1 & 2) (Vs×0.14) (Vs/2) (Vs-(Vs×0.14))0.7 2.5 4.3 VDC typ.Inverted value on output signal 2.Custom values available upon request.

Output Voltage Mechanical & Temp. Tolerance ±0.2V max.

Output Resolution 12 bit ratiometric to Vs (full scale output, 0-5 VDC)

Max. Recommended Output Current 1 mA.

Short Circuit Protection 10 minutes max.

14 PROPORTINAL THUMBWHEEL

THUMBWHEEL SVAB HECR(continued)

Environmental Characteristics

Operating Temperature -40°C to 70°C.

Storage Temperature -40°C to 85°C.

EMI/RFI 100 V/m and 200 mA BCI, 150 kHz to 2 GHz.

EMI Output Tolerance ±0.45V @ DC 25 mT (Area 1).±0.35V @ DC 25mT (Area 2), mounted in L8 handle.±0.25V @ DC 25 mT (Area 3), with additional shiel-ding*

ESD Handling ±8 kV.

ESD Operating ±15 kV air discharge.±8 kV contact discharge.

Output Signal Diagram

HECR Product Specification

Output Signal Diagram

Wiring Information Cvilux CI01-04S 1 – GND 2 – Output signal 1 3 – Output signal 2 4 – +5V

1234

Mechanical Characteristics

Rotational Cycles >4,000,000

Rotational Angle ±40°

Wiring Information

Cvilux CI01-04S

1234

1 – GND2 – Output signal 13 – Output signal 24 – +5V

PUSHBUTTONS 15

5. PUSHBUTTONS

PUSHBUTTON STANDARD OTTO (P9) TECHNICAL DATA

Info:

The P9 Dome series pushbutton switches feature a contoured dome sty-le pushbutton and share similar size and characteristics to the P7 series. Major differences are plastic housing construction and the availability of a shorting bar contact arrangement. There are two button versions: low button profile and high button profile. The P9 comes with a threaded case for hex nut mounting or with a snap-in case. The switch series features short behind panel depth. They also offer excellent mechani-cal and electrical performance while operating under severe conditions found in demanding applications.

The buttons are specified at 5Amps/4Amps. However SVAB adds a CVI-LUX connector which lower the tolerance to 2Amps.

The P9 Dome series is offered in dusttight and moistureproof sealed construction. One million mechanical operations and an electrical life of 25,000 operations at full rated load of 5 amps resistive or 3 amps inductive.

Watertight sealing is available simply by adding a “W” suffix to the part number to specify IP68S rating.

The P9 Dome series is available in standard and low-force double break snap-action and non-snap shorting bar models. All are momentary ac-tion. Special contact variations are available. High contact pressure and unique contact design provide low contact resistance for low level swit-ching capability as well as full rated service. Solder, PC Pin, and 0.110” Quick Connect termination options are available.

Positive tactile feedback signaling the operator when the switch is ope-rated is available in snap-action models but not shorting bar models.

The P9 Dome series is a quality precision switch designed for use in pa-nels, control grips, computers, instruments, heavy equipment and other demanding applications where attractive, rugged pushbutton switches are required.

Features:

• Attractive dome style button• 2 button heights• Double break or shorting bar, momentary action• All plastic housing & button construction• Threaded body or snap-in panel mounting• Withstands extreme shock & vibration• Positive tactile feedback contact transfer on snap-action models• Solder, PC Pin & 0.110” Quick Connect• terminal styles• Moistureproof & dusttight to IP64 or watertight to IP68S• UL recognized & CSA certified• RoHS/WEEE/Reach compliant

Tip!

The ”Tall Hat” -model is ideal when used as a ”dead man button” on the SVAB Grip L8 back side.

A Ø15,2

Tall Hat

Standard Matte

Electrical Ratings(sea level @ 28VDCor 115VAC,60/400Hz)Load N.O./N.C 2 2 Circuit

Resistive 2A (5A) 2A (4A)

Inductive 2A (3A) 2A

DWV 1050Vrms

Low Level 10mA @ 30mV

Electrical Life 25,000 cycles 5A @ 28VDC resistive snap-action

Mechanical Life 1,000,000 cycles

Seal IP64 or IP68S

Operating Temp. Range

-40°C to +85°C

Operating Force Standard: 1.7 lbs. +/- 0.5 lb.Low Force: 12 oz +/- 4 ozShorting Bar: 18 oz +/- 6 oz

Total Travel 0.080 inches max

Overtravel 0.010 inches min

Materials

Case Thermoplastic

Button Thermoplastic

Terminals Brass with gold over silver

Terminal Hard-ware

None provided

Mounting Hard-ware

Hex nut, lockwasherPanel gasket when applicable

Available Button Colors

Black, Green, Gray, Red, Yel-low, Blue

16 PUSHBUTTONS

PUSHBUTTON DOUBLE PRESS ITW (48EM) TECHNICAL DATA

Info:

Double press ITW is our option when a distinct re-maining button press is desired. When pressing the button it remains pressed down until the button is pressed again Features:

• Maintained action• Gold contacts• Long life• Solder or PC terminals• Panel sealed to IP 67

A Ø15,2

Circuit SPST-NO-DB

Button travel (nominal) 0.09 inches / 2.3 mm

Operating force (nominal) 3N / 306 grams

Contact bounce (nominal) 1 millisecond

Panel thickness 0.02 – 0.12 inches / 0.5 – 3mm

Temperature index -40° F to + 185° F

Current ratings (resistive) 250mA @ 12VDC, 100K cycles150mA @ 28VDC, 150K cycles (momentary)100mA @ 48VDC, 100K cycles10mA @ 12VDC, 1 million cycles (momentary)

Dielectric strength 1,000 VAC

Insulation resistance 1G OHM

Contact resistance 50 mΩ max (initial)

Torque (max) 10 inch pounds

TOGGLE SWITCHES, LED:S AND MINITRIM 17

6. TOGGLE SWITCHES, LEDs AND MINITRIM

TOGGLE SWITCH TAIWAY (SERIES 100 SPDT) TECHNICAL DATA

Info:

The toggle switch is specified at 5Amps. However SVAB adds a CVILUX connector which lower the tole-rance to 2Amps.

C Ø6,5

TypesModel No.

Switching Position

SP-1 ON NONE ON

SP-3 ON OFF ON

SP-4 (ON) OFF (ON)

SP-5 ON OFF (ON)

Term.Comm. 2-3 OPEN 2-1

SchematicO2Comm.

Specifications

Contact rating Silver plated (movable contact / Terminals: Copper alloy, silver plated).

2Amps (5Amps) @ 125VAC or 28VDC 2Amps @ 250VAC

Agency Approval:

Electrical life 50,000 make-and-break cycles at full load.

Contact resistance 10mΩmax. initial @2-4VDC 100mA for both silver and gold plated contacts.

Insulation resistance 1,000M Ωmin.

Dielectric strength 1,500V RMS @ sea level.

Operating tempera-ture

-30˚C to +85˚C

Materials

Case Diallyl phthalate(DAP)(UL 94V-0)

Toggle handle Brass, chrome plated.

Bushing Brass, nickel plated.

Housing Stainless steel.

Terminal seal Epoxy.

Actuator cap material PVC (red)

18 TOGGLE SWITCHES, LED:S AND MINITRIM

TOGGLE SWITCH SMGTECHNICAL DATA

B Ø12

TypesModel No.

Switching Position

V7 ON OFF ON

V6 (ON) OFF (ON)

Specifications

Rating 50mA 28V DC

Initial contact resistance

20mΩ max. at 1.5mA 200µV AC (1kHz)

Insulation resistance 1,000MΩ min. at 500V DC. (between termi-nals and terminals and earth)

Dielectric strength 1,000V AC(between terminals).1,500V AC(between terminals and earth) for 1 minute.

Endurance (Electrical life)

No damage electrical and mechanical func-tion after 25,000 cycles (20 cycles/minute) at the rating.

Endurance (Mechanical life)

No damage electrical and mechanical func-tion after 100,000 cycles (20 cycles/minute) at no load.

Water proofing 30 minutes at 1 meter water column : IP67

Lever strength 39.2N applied to the top of lever side from 90 degree angle of lever axis

Operating force 0.49~7.85N(50~800gf)

Accessory Cap and screw: Each one piece attached.

Materials

Case Diallyl phthalate resin (green)

Common terminal Phosphor bronze, silver plated

Fixed terminal Copper, silver plater

Frame Stainless steel

Bushing Brass, nickel plated

Cap Polybutylene terephalate

Screw Brass, nickel plated

O Ring Nitril rubber

TOGGLE SWITCHES, LED:S AND MINITRIM 19

PUSHBUTTON LED BUTTON APEM (IP) TECHNICAL DATA

NOTE! The APEM LED button may require a unique solution to be integrated with the machine or sys-tem. Always consult a SVAB sales representative before the selection of the LED button is made.

Info:

The APEM LED button can be used when you want to signal that a function has an “on” or “off” state. This by the LED remaining lit while the function is still active.

The pushbutton is specified at 5Amps. However SVAB adds a CVILUX connector which lower the tole-rance to 2Amps.

Features:

• Illuminated (LED).• Tactile feedback.• Flat round actuator for optional marking.• Sealed to IP67.

A Ø15,2

Environmental specifications

Front panel sealing IP67 according to IEC 60529

Shock resistance 100 g according to IEC 512-4, test 6c

Vibration resistance 10-500Hz - 10 g according to IEC 512-4, test 6d

Salt spray IEC 512-6, test 11f

Operating temperature -40°C to +85°C

Electrical specifications

Max. current/voltage rating with resistive load (gold plated silver contacts)

2A (5A) 28VDC, 70.000 cycles0,2A 48VDC, 500.000 cycles0,5A 48VAC, 500.000 cycles

Initial contact resistance 100 mΩ max.

Insulation resistance 1 GΩ min. at 500VDC

Dielectric strength 1.500 Vrms

Contact bounce 10 ms

Green LED

(A resistor must be series-connected by the user.

Resistor value = sup-ply voltage (minus) LED forward voltage (divided by) LED forward current

Forward current: 20mATyp. forward voltage: 2,1VMax. forward voltage: 2,3V

General specifications

Panel thickness 1,5 mm (.059) min.4 mm (.157 max.)

Total travel Funct. 3 : 1,7 mm (.067) +/- 0,3 mmFunct. 5 : 1,3 mm (.051) +/- 0,3 mm

Typical operating force 6N +/- 2N

Mechanical life 1.000.000 cycles

Torque 1,5 Nm max. applied to nut

Soldering 320°C max. for 3 sec.

20 TOGGLE SWITCHES, LED:S AND MINITRIM

PUSHBUTTONLED BUTTON APEM(continued)

Materials

Case thermoplastic UL94-V0

Actuator polyamide 6/6

Bushing/bezel zinc die-cast (zamac), black painted

Contacts silver, gold plated

Multi-wire lead AWG20, section 0,6 mm²

LED wire AWG26, section 0,12 mm2

Lens polycarbonate

Terminal seal epoxy

Available button color Black

Agency approval

2A 125VAC/250VACFile E83438

Availability consult factory for details of approved models.

Marking to order switches marked UL, complete ordering format

LED5V, 12V, 24V TECHNICAL DATA

NOTE! The L8 LED may require a unique solution to be integrated with the machine or system. Always consult a SVAB sales representative before the selec-tion of an LED is made.

Info:

The LED can be used when you want to signal that a function has an “on” or “off” state. This by the LED remaining lit while the function is still active.

D Ø4,4

Light Color Green

Wavelength (top) 565 nm

Brightness 8...20 mcd

Forward Voltage 5V, 12V

Capsule 3mm (T1)

Capsule Color Green

Capsule Type Diffuse

Beam angle 40 ˚

Forward Voltage Nominal (5V)12mA, (12V)11mA

Technology GaP

TOGGLE SWITCHES, LED:S AND MINITRIM 21

MINITRIM OTTO T8 TECHNICAL DATA

NOTE! Minitrim may require a unique solution to be integrated with the machine or system. Always con-sult a SVAB sales representative before the selection of the Minitrim is made.

The Minitrim does not occur in any of the hole pat-tern layouts and thereby cannot be configured in the product configuration code.

Contact a SVAB sales representative if you are inter-ested in Minitrim OTTO.

Info:

OTTO Minitrim gives the L8 joystick grip an additional digital XY “mini joystick” on the front plate of the L8 joystick grip.

For more information on alternative Minitrim button styles, see ottoexcellence.com.

Electrical Ratings

Load Rating

Resistive 10mA @ 5VDC (low level)

Inductive 1A @ 28VDC

DWV 1050Vrms

Low Level 10mA Resistive @ 5VDC

Electrical Life 100,000 cycles 1A Inductive @ 28VDC

Lever Travel Toggle: 15° max from center OFF

Seal IP64 or IP68S or MIL-PRF-8805 Design 3

Operating Temp Range -55°C to +85°C

Operating Force Toggle: 16 oz +/- 6 oz

Lever Pivot & Stop Strength

Switch is capable of withstanding a force of 25.0 lbs. applied to the actuating button. The button also withstands 15.0 lbs. mini-mum pull force.

Materials

Case Aluminum alloy or thermoplastic

Button Thermoplastic

Terminals Silver over brassBrass with gold over silver for low level

Terminal Hardware None provided

Mounting Hardware Hex nut, tooth lockwasher, panel seal gas-ket where applicable

22 ATTACHMENTS

7. MOUNTINGS

The L8 joystick grip is attached on the joystick base with mountings and accessories. Mountings and accessories allows the joystick grip to be fitted on a large variety of joystick bases.

STANDARD DIMENSIONS (in millimeter) NOTE! Accessories for mountings, like the adapter ball kit, is sold separately.

See “ADAPTER BALL KIT FOR STANDARD MOUNTING L8” on page 27.

Info: Standard mounting that with the help of acces-sories fit a wide range of joystick bases.

ATTACHMENTS 23

OPTION 1 DIMENSIONS (in millimeter)

Info: Option 1 has been developed for Penny + Giles joystick base JC6000 but it can also fit other brands of joy-stick bases.

Option 1 is fitted directly on the JC6000 joystick base.

44

A

A

9

6

23,90 -0,100

23,9

0

6R8

9,50 0+10

50°

2,4 SECTION A-A M5(2x)

24 PRODUCT CONFIGURATION CODE

8. PRODUCT CONFIGURATION CODE

The product configuration code allows you to configure and specify your L8 joystick grip so that we at SVAB quickly and efficiently can meet your requirements.

Accessories (page 26) such as bellow washers and adapter kits are not included in the product configura-tion code. The accessories are ordered separately.

8.1 L8 JOYSTICK GRIP POSITIONS

FRONT PLATE LEFT

BACK SIDE LEFT

BACK SIDE RIGHT

FRONT PLATE RIGHT

3

6 45

12

1

2

3

4

1

2

3

4

1

4 65

32

A H

D F G Positions 1-6 refers to the joystick grip front plates six different positions as shown below (8.1 L8 JOYSTICK GRIP POSITIONS). Here, thumbwheels, pushbuttons and toggle switches can be placed according to the selected hole pattern layout (as seen in table C on page 25).

In each position the first and second letter specifies the component code (as seen on page 25).

With the third letter you specify whether the thumbwheel, push-button or toggle switch communicates via analog/digital (A) or SVAB CAN-bus (C) communication. SVAB CAN-bus requires a control system from SVAB.

# indicates that the position is occupied by a thumbwheel. A thumb-wheel always occupies two positions.

E F * Positions 1-4 refers to the joystick grips back side as shown below (8.1 L8 JOYSTICK GRIP POSITIONS). Here, a thumbwheel and pushbuttons can be placed.

In each position the first and second letter specifies the component code (as seen on page 25).

With the third letter you specify whether the thumbwheel or pushbutton communicates via analog/digital (A) or SVAB CAN-bus (C) communication. SVAB CAN-bus requires a control system from SVAB.

# indicates that the position is not used and thereby replaced by a plug.

NOTE!The back side position 3 cannot be plugged and must therefore contain a pushbutton or a toggle switch.

* The back side position 3 can also be fitted with the TAIWAY toggle switch (V1-V4).B C

Position front plate Position back side

1 12 23 34 45 6L 8 0R 10V# P0 00 #P 00 17# 11 11 #1 11 AC# CA AA #C AN/ / / /- -- -- -- -

PRODUCT CONFIGURATION CODE 25

This symbol indicates that more information is found on the referred to page.

A Right or left joystick grip ( 6)

Code DescriptionL8 R Right gripL8 L Left grip

B Grip color ( 6)Code Description0 Gray1 Black

C Hole pattern layout for thumbwheels (TW), pushbuttons and toggle switches on the front plate ( 10)

Code Description10 1-2 TW11 1-2 TW, 3A12 1-2 TW, 4A, 5A13 1-2 TW, 4A, 5B, 6A14 1-2 TW, 3A, 4A, 5A, 6A15 1-2 TW, 3A, 6A16 1-4 TW, 2A, 3A, 5A, 6A18 1-2 TW, 3A, 4A, 5C, 6A19 1-2 TW, 3A, 4B, 5B, 6A20 1-2 TW, 4-5 TW21 1-2 TW, 3A, 4-5 TW22 1-2 TW, 3A, 4-5 TW, 6A

Code Description23 1-4 TW, 2-5 TW, 3A24 1-4 TW, 2-5 TW, 3A, 6A25 1-2 TW, 3A, 4-5 TW, 6B32 1A, 2A33 1A, 2A, 3A35 1A, 2A, 3A, 4A, 5A36 1A, 2A, 3A, 4A, 5A, 6A1A 1-2 TW, 3A, 4A, 5A26 1-2 TW, 3B, 4-5 TW27 1-4 TW, 2-5 TW, 3B28 1-4 TW, 3A37 1-2 TW, 3A, 5B

Code Description1D 1-4 TW, 2-5 TW, 3A, 6C39 1-2 TW, 3A, 4B1G 1-2 TW, 3A, 4A, 5B, 6A, 7D1F 1-2 TW, 3A, 4A, 5A, 6C1H 1-2 TW, 3A, 4A, 5B1I 1-2 TW, 3A, 4B, 5A1J 1A, 2A, 3A, 5D1K 1-2 TW, 3A, 4A, 5B, 6D1L 1-2 TW, 3A, 2-4 TW, 6D1N 1-4 TW, 2A, 3A, 5B, 6A1P 1-2 TW, 3A, 4B, 5A, 6A

This table shows the positions (1-6) of thumbwheels, pushbuttons and toggle switches in the “hole pattern layout” according to “8.1 L8 JOYSTICK GRIP POSITIONS”. The letters A, B, C and D indicates hole diameter ( 10).

D Front plate thumbwheels ( 13)Code DescriptionP1_ HECR 0,7-4,3 VDCQ1_ HECR 0-5 VDCQ2_ HECR 0,5-4,5 VDCQ3_ HECR 1,35-3,65 VDC

E Back side thumbwheel ( 13)Code DescriptionR1_ HECR 0,7-4,3 VDCS1_ HECR 0-5 VDCS2_ HECR 0,5-4,5 VDCS3_ HECR 1,35-3,65 VDC

H Mountings ( 22)Code Description01 Standard

NOTE! accessories my be required in order to fit the grip on the joystick base with the standard mounting, see 9.1 ADAPTER BALL KIT FOR STAN-DARD MOUNTING L8 page 27.

02 Option 1

F Pushbuttons ( 15)Code Description01_ Button std. OTTO (P9), black - Diameter: A12_ Button double press ITW (48EM) - Diameter: A13_ Button OTTO (P9), green - Diameter: A14_ Button OTTO (P9), gray - Diameter: A15_ Button OTTO (P9), red - Diameter: A16_ Button OTTO (P9), yellow - Diameter: A17_ Button OTTO (P9), blue - Diameter: A18_ Button OTTO (P9), ”Tall Hat” - Diameter: A

G Toggle switches, LEDs and minitrim ( 17)Code DescriptionV1_ Switch TAIWAY SP1 1-1 - Diameter: CV2_ Switch TAIWAY SP3 1-0-1 - Diameter: CV3_ Switch TAIWAY SP4 (1)-0-(1) - Diameter: CV4_ Switch TAIWAY SP5 1-0-(1) - Diameter: CV6_ Switch SMG (1)-0-(1) - Diameter: BV7_ Switch SMG 1-0-1 - Diameter: B19_ Knapp APEM with green LED - Diameter: AV9_ LED, green, 5V - Diameter: DV0_ LED, green. 12V - Diameter: DVB_ OTTO Minitrim T8

NOTE! Minitrim does not exist in any layout and cannot be configured in the product configuration code. Contact SVAB if you are interested in the minitrim.

26 ACCESSORIES

9. ACCESSORIES

Accessories allows the SVAB Grip L8 joystick grip to be fitted on market joystick bases.

Among the accessories, bellow washers and adapters can be found which facilitates the attachment of the joystick base bellow to the joystick grip.

Accessories are ordered separately and are not included in the product configuration code (page 24).

ACCESSORIES 27

9.1 ADAPTER BALL KIT FOR STANDARD MOUNTING L8

The ball head screw allows attachment of the L8 joystick grip to the joystick base with the use of a locking plate.

ADAPTER BALL KIT FOR STANDARD MOUNTING L8 DIMENSIONS (in millimeter)

Info:

This kit is compatible with the L8 joystick grip standard mounting (page 22).

The kit includes ball screws, locking plate and screws for the locking plate. The kit comes with three different standard size screws for attachment to the joystick base. M12, M14 and m14x1,5.

315

2

42

8

8

Ordering information

Description Article no.

Adapter ball kit L8 M12 , M14 & M14x1,5 167110

28 ACCESSORIES

9.2 BELLOW WASHERS

Bellow washers allows for the attachment of the joystick base bellow to the L8 joystick grip.

STANDARD BELLOW WASHER FOR STANDARD MOUNTING DIMENSIONS (in millimeter)

Info:

Bellow washer in spring steel for ”Stan-dard mounting” (page 22).

Enables the attachment of the joystick base bellow to the L8 joystick grip.

R24

10,80

26

4

R3,50

2

Ordering information

Description Article no.

Bellow washer with screws 167120

ACCESSORIES 29

9.3 BELLOW ADAPTERS FOR STANDARD BELLOW WASHER

If the joystick bases upper bellow hole is too large to fit the standard bellow washer, a bel-low adapter may be required.

The bellow adapter allows for attaching bel-lows with large upper holes to the L8 joystick grip.

Contact SVAB if you do not find a suitable mea-sure among existing bellow adapters.

BELLOW ADAPTER D76 FOR STANDARD BELLOW WASHER DIMENSIONS (in millimeter)

Info:

The bellow adapter allows for attaching bellows with large upper holes to the L8 joystick grip.

Black POM plastic.

76

A A

48,50

44,50

3xR 0,50

2,5

0

1,5

0 3

56

SECTION A-A

6

Ordering information

Description Article No.

Bellow adapter L8 D76 200572

30 ACCESSORIES

BELLOW ADAPTER 65x81 FOR STANDARD BELLOW WASHER DIMENSIONS (in millimeter)

Info:

The bellow adapter allows for attaching bellows with large upper holes to the L8 joystick grip.

Black POM plastic.

81

65

R20

40,50

32,

50

6

A

A

48

44

2 6

3

SECTION A-A

Ordering information

Description Article No.

Bellow adapter L8 65x81 200424-1

SVAB Hydraulik AB has extensive experience in hydraulics, control electronics and ergonomic design for industrial ve-hicles, with guaranteed quality production and prompt delivery.

SVAB Hydraulik AB Ulvsättersgatan 2SE-69491 HALLSBERG SWEDEN

Phone: +46 (0)582 15230 Fax: +46 (0)582 15232 E-mail: info@svab.se Web: www.svab.se