Stock List 2012

Stock List 2012

Since 1935 ...because quality matters

Published by Hobson Engineering Co. Pty. Ltd.P.O. Box 320 Horsley Park N.S.W. 2175

Look out for other released Hobson Publications.

Sydney Brisbane Melbourne Perth10 Clay Place 56 Axis Place Unit 1 155 Abbotts Road 133 Beringarra Ave

Eastern Creek NSW 2766 Larapinta Qld 4110 Dandenong South Vic 3175 Malaga WA 6090

Ph: (02) 8818 0222 Ph: (07) 3273 0777 Ph: (03) 9797 3333 Ph: (08) 9241 9888

Fax: (02) 9620 1850 Fax: (07) 3711 4551 Fax: (03) 9799 3081 Fax: (08) 9248 8806

email: [email protected] email: [email protected] email: [email protected] email: [email protected]

www.hobson.com.au

Hobson Engineering Co. Pty. LtdA.B.N. 38 000 289 958

Quality Fasteners Since 1935

All rights reserved. Hobson Engineering Co. Pty. Ltd. is the owner of the copyright subsisting in this publication. Other than permitted by the Copyright Act, no part of this publication can be reproduced, copied or transmitted, in any form or by any means (electric, mechanical, photocopying, recording, storage in a retrieval system or otherwise), without the prior written consent of Hobson Engineering Co. Pty. Ltd. Hobson Engineering Co. Pty. Ltd. will vigorously pursue any breach of its copyright.

This publication is distributed on the basis and understanding that the publisher is not responsible for the results of any actions taken on the basis of information in this publication, nor for any error in or omission from this publication The publisher expressly disclaims all and any liability and responsibility to any person, whether a reader of this publication or not, in respect of anything, and the consequences of anything, done or omitted to be done by any such person in reliance, whether wholly or partially, upon the whole or any part of the contents of this publication. Without limiting the generality of the foregoing the publisher accepts no liability for any loss or damage either direct or consequential arising out of or in relation to the use or application of the information or products referred to herein.

Since 1935 ...because quality matters 1

Index

Metal 2Flange Hex

Series 500 4

CSK & Bugle 5Trim & Wafer 6PAN, CSK & Flower 7+ Wings 8Type 17 9Flange Hex

PAN, CSK & Wafer 11Bugle & Chipboard 12Needle Point 13Bugle, Flange Hex & Wafer 14304 Stainless 15Bugle, CSK, Trim & TDX

316 Stainless 17Flange Hex & Button

Self Embed & Bugle 18

2 . Quality Fasteners Since 1935

HEX HEAD / NO SEAL AS3566 CLASS 4

Part QFind Size (TPI) Length Thread Hex Flange Pack

(mm)

TSMC4PFH#080012 Q173 8G 18 12 Full 1/4 1000

TSMC4PFH#100016 Q180 10G 16 16 Full 5/16 1000

TSMC4PFH#100022 Q183 10G 16 22 Full 5/16 1000

TSMC4PFH#100025 Q185 10G 16 25 Full 5/16 1000

TSMC4PFH#120020 Q190 12G 14 20 Full 5/16 1000

TSMC4PFH#120025 Q509 12G 14 25 Full 5/16 1000

TSMC4PFH#120030 Q193 12G 14 30 Full 5/16 1000

TSMC4PFH#120035 Q195 12G 14 35 Full 5/16 1000

TSMC4PFH#120045 Q200 12G 14 45 Full 5/16 1000

TSMC4PFH#140022 Q220 14G 14 22 Full 3/8 1000

TSMC4PFHF140022 Q254 14G 20 22 Full 3/8 1000

HEX HEAD / WITH SEAL AS3566 CLASS 4


(mm)

TSMC4PNH#080012 Q273 8G 18 12 Full 1/4 1000

TSMC4PNH#080020 Q274 8G 18 20 Full 1/4 1000

TSMC4PNH#100016 Q275 10G 16 16 Full 5/16 1000

TSMC4PNH#100022 Q278 10G 16 22 Full 5/16 1000

TSMC4PNH#100025 Q280 10G 16 25 Full 5/16 1000

TSMC4PNH#120020 Q285 12G 14 20 Full 5/16 1000

TSMC4PNH#120030 Q288 12G 14 30 Full 5/16 1000

TSMC4PNH#120035 Q290 12G 14 35 Full 5/16 1000

TSMC4PNH#120045 Q300 12G 14 45 Full 5/16 1000

TSMC4PNH#140022 Q325 14G 14 22 Full 3/8 1000

TSMC4PNH#140042 Q330 14G 10 42 Full 3/8 1000

Flange Hex Metal SDSClass 4 Hex Head/No Seal

HEX HEAD / NO SEAL AS3566 CLASS 2


(mm)

TSMC2PFH#080012 Q505 8G 18 12 Full 1/4 1000

TSMC2PFH#100016 Q506 10G 16 16 Full 5/16 1000

TSMC2PFH#100025 Q507 10G 16 25 Full 5/16 1000

3 Quality Fasteners Since 1935

HEX HEAD WITH SEAL AS3566 CLASS 4


(mm)

TSMC4PXH#120037 Q295 12G 14 37 15 5/16 1000

HEX HEAD / WITH SEAL / SCRATCHGUARD®AS3566 CLASS 4


(mm)

TSMC4PNHS120055 Q310 12G 14 55 30 5/16 1000

TSMC4PNHS140050 Q335 14G 10 50 25 3/8 1000

TSMC4PNHS140065 Q340 14G 10 65 40 3/8 500

TSMC4PNHS140090 Q350 14G 14 90 65 3/8 500

TSMC4PNHS140115 Q260 14G 14 115 90 3/8 250

TSMC4PNHS140150 Q270 14G 14 150 100 3/8 250

HEX HEAD WITH SEAL / SCRATCHGUARD® AS3566 CLASS 4


(mm)

TSMC4PXHS120048 Q305 12G 14 48 20 5/16 1000

TSMC4PXHS120055 Q306 12G 14 55 22 5/16 1000

GRPX®

GRPX®

ME

TAL

Flange Hex Metal SDSClass 4


S500 SDSClass 3 / 4

WAFER HEAD S500 POINT PHILLIPS AS3566 CLASS 3

Part QFind Size (TPI) Length Thread Phillips Drive Pack

(mm)

TS5C3PWP#120038 QA15 12G 24 38 Full #3 1000

HEX HEAD S500 POINT / NO SEAL AS3566 CLASS 4


(mm)

TS5C4PFH#120032 Q480 12G 24 32 Full 5/16 1000

TS5C4PFH#120050 Q482 12G 24 50 Full 5/16 1000

TS5C4PFH#120065 Q484 12G 24 65 Full 5/16 1000

HEX HEAD S500 POINT / WITH SEAL AS3566 CLASS 4


(mm)

TS5C4PNH#120032 Q486 12G 24 32 Full 5/16 1000

TS5C4PNH#120050 Q488 12G 24 50 Full 5/16 1000

TS5C4PNH#120065 Q490 12G 24 65 Full 5/16 1000


CSK & Bugle Metal SDSClass 2 / 3 / 4

COUNTERSUNK HEAD PHILLIPS AS3566 CLASS 2 (Zinc Yellow)


(mm)

TSMC2PCP#060020 QA12 6G 20 20 Full #2 1000

TSMC2PCP#080025 QA13 8G 18 25 Full #2 1000

TSMC2PCP#100025 QA14 10G 24 25 Full #2 1000

TSMC2PCP#100030 Q460 10G 24 30 Full #2 1000

TSMC2PCP#100040 Q462 10G 24 40 Full #2 1000

COUNTERSUNK HEAD PHILLIPS AS3566 CLASS 3


(mm)

TSMC3PCP#080025 QA05 8G 18 25 Full #2 1000

TSMC3PCP#100025 QA06 10G 24 25 Full #2 1000

TSMC3PCP#100030 QA07 10G 24 30 Full #2 1000

TSMC3PCP#100040 QA08 10G 24 40 Full #2 1000

BUGLE HEAD PHILLIPS AS3566 CLASS 2 (Zinc Yellow)


(mm)

TSMC2PBP#060025 Q440 6G 20 25 Full #2 1000

TSMC2PBP#060030 Q442 6G 20 30 Full #2 1000

TSMC2PBP#060045 Q444 6G 20 45 Full #2 1000

BUGLE HEAD PHILLIPS AS3566 CLASS 3


(mm)

TSMC3PBP#080075 QA09 8G 18 75 Full #2 1000

TSMC3PBP#100100 QA10 10G 16 100 75 #2 500

ME

TAL


Trim & Wafer Metal SDSClass 2 / 3

TRIM HEAD MINI PHILLIPS AS3566 CLASS 3


(mm)

TSMC3PMP#100020 Q461 10G 16 20 Full #2 1000

TSMC3PMP#100030 Q463 10G 16 30 Full #2 1000

WAFER HEAD PHILLIPS AS3566 CLASS 3


(mm)

TSMC3PWP#080012 Q378 8G 18 12 Full #2 1000

TSMC3PWP#100016 Q380 10G 16 16 Full #2 1000

TSMC3PWP#100022 Q382 10G 16 22 Full #2 1000

TSMC3PWP#100030 Q384 10G 16 30 Full #2 1000

TSMC3PWP#100040 Q386 10G 16 40 Full #2 1000

TSMC3PWP#100050 Q387 10G 16 50 Full #2 1000

WAFER BUTTON HEAD PHILLIPS AS3566 CLASS 2 (Zinc Yellow)


(mm)

TSMC2PAP#080012 Q430 8G 18 12 Full #2 1000

TSMC2PAP#080016 Q432 8G 18 16 Full #2 1000

TSMC2PAP#080020 Q434 8G 18 20 Full #2 1000

TSMC2PAP#080025 Q436 8G 18 25 Full #2 1000

TSMC2PAP#080032 Q438 8G 18 32 Full #2 1000

WAFER BUTTON HEAD PHILLIPS AS3566 CLASS 3


(mm)

TSMC3PAP#080012 Q431 8G 18 12 Full #2 1000

TSMC3PAP#080016 Q433 8G 18 16 Full #2 1000

TSMC3PAP#080020 Q435 8G 18 20 Full #2 1000

TSMC3PAP#080025 Q437 8G 18 25 Full #2 1000

TSMC3PAP#080032 Q439 8G 18 32 Full #2 1000


Pan, CSK & Flower Metal SDSClass 2 / 3

PAN HEAD PHILLIPS AS3566 CLASS 2 (Zinc Yellow)


(mm)

TSMC2PPP#060012 Q495 6G 20 12 Full #2 1000

TSMC2PPP#080012 Q500 8G 18 12 Full #2 1000

TSMC2PPP#080020 Q504 8G 18 20 Full #2 1000

COUNTERSUNK RIBBED HEAD PHILLIPS AS3566 CLASS 2 (Zinc Yellow)


(mm)

TSMC2PRP#080020 Q470 8G 18 20 Full #2 1000

TSMC2PRP#080025 Q471 8G 18 25 Full #2 1000

TSMC2PRP#080030 Q472 8G 18 30 Full #2 1000

COUNTERSUNK RIBBED HEAD PHILLIPS AS3566 CLASS 3


(mm)

TSMC3PRP#080030 Q475 8G 18 30 Full #2 1000

FLOWER HEAD SELF EMBEDDING PHILLIPS AS3566 CLASS 2 (Zinc Yellow)


(mm)

TSMC2POP#080020 QA11 8G 18 20 Full #2 1000

FLOWER HEAD SELF EMBEDDING WITH WINGS SQUARE DRIVE AS3566 CLASS 2 (Zinc Yellow)

Part QFind Size (TPI) Length Thread Square Drive Pack

(mm)

TWMC2POQ#080035 Q425 8G 18 35 Full #2 1000

ME

TAL


COUNTERSUNK RIBBED HEAD WITH WINGS SQUARE DRIVE AS3566 CLASS 2 (Zinc Yellow)


(mm)

TWMC2PRQ#100030 Q414 10G 16 30 Full #2 1000

TWMC2PRQ#100035 Q415 10G 16 35 Full #2 1000

TWMC2PRQ#100040 Q416 10G 16 40 Full #2 1000

TWMC2PRQ#100045 Q418 10G 16 45 Full #2 500

TWMC2PRQ#100050 Q419 10G 16 50 Full #2 500

TWMC2PRQ#100060 Q421 10G 16 60 Full #2 500

TWMC2PRQ#100070 Q423 10G 16 70 Full #2 500

COUNTERSUNK RIBBED HEAD WITH WINGS SQUARE DRIVE AS3566 CLASS 3


(mm)

TWMC3PRQ#080022 Q395 8G 18 22 Full #2 1000

TWMC3PRQ#080032 Q400 8G 18 32 Full #2 1000

TWMC3PRQ#080040 Q399 8G 18 40 Full #2 1000

TWMC3PRQ#100035 Q401 10G 16 35 Full #2 1000

TWMC3PRQ#100040 Q402 10G 16 40 Full #2 1000

TWMC3PRQ#100045 Q404 10G 16 45 Full #2 500

TWMC3PRQ#100050 Q405 10G 16 50 Full #2 500

TWMC3PRQ#100060 Q407 10G 16 60 Full #2 500

CSK + Wings Metal SDSClass 2 / 3


T17 HEX HEAD / NO SEAL AS3566 CLASS 4


(mm)

TSWC4PFH#100020 Q519 10G 12 20 Full 5/16 1000

TSWC4PFH#100030 Q523 10G 12 30 Full 5/16 1000

TSWC4PFH#120025 Q525 12G 11 25 Full 5/16 1000

TSWC4PFH#120030 Q526 12G 11 30 Full 5/16 1000

TSWC4PFH#120040 Q530 12G 11 40 Full 5/16 1000

TSWC4PFH#140025 Q545 14G 10 25 Full 3/8 1000

TSWC4PFH#140040 Q550 14G 10 40 Full 3/8 1000

T17 HEX HEAD / WITH SEALAS3566 CLASS 4


(mm)

TSWC4PNH#100020 Q595 10G 12 20 Full 5/16 1000

TSWC4PNH#100030 Q596 10G 12 30 Full 5/16 1000

TSWC4PNH#120025 Q600 12G 11 25 Full 5/16 1000

TSWC4PNH#120030 Q601 12G 11 30 Full 5/16 1000

TSWC4PNH#120035 Q602 12G 11 35 Full 5/16 1000

TSWC4PNH#120040 Q603 12G 11 40 Full 5/16 1000

TSWC4PNH#140025 Q615 14G 10 25 Full 3/8 1000

TSWC4PNH#140040 Q620 14G 10 40 Full 3/8 1000

T17 HEX HEAD / NO SEAL / SCRATCHGUARD® AS3566 CLASS 4


(mm)

TSWC4PFHS1200405 Q535 12G 11 45 30 5/16 1000

TSWC4PFHS120050 Q540 12G 11 50 35 5/16 1000

TSWC4PFHS1200605 Q543 12G 11 65 43 5/16 1000

TSWC4PFHS140050 Q555 14G 10 50 37 3/8 1000

TSWC4PFHS1400605 Q560 14G 10 65 43 3/8 500

TSWC4PFHS1400705 Q565 14G 10 75 50 3/8 500

TSWC4PFHS140090 Q570 14G 10 90 50 3/8 500

TSWC4PFHS140100 Q575 14G 10 100 50 3/8 500

TSWC4PFHS1401105 Q580 14G 10 115 60 3/8 250

TSWC4PFHS1401205 Q585 14G 10 125 60 3/8 250

TSWC4PFHS140150 Q590 14G 10 150 100 3/8 250

TY

PE

17

Flange Hex Type17 SDSClass 4


T17 HEX HEAD / WITH SEAL / SCRATCHGUARD®AS3566 CLASS 4


(mm)

TSWC4PNHS120045 Q605 12G 11 45 30 5/16 1000

TSWC4PNHS120050 Q610 12G 11 50 35 5/16 1000

TSWC4PNHS120065 Q613 12G 11 65 43 5/16 1000

TSWC4PNHS140050 Q625 14G 10 50 37 3/8 1000

TSWC4PNHS140065 Q630 14G 10 65 43 3/8 500

TSWC4PNHS140075 Q635 14G 10 75 50 3/8 500

TSWC4PNHS140090 Q640 14G 10 90 50 3/8 500

TSWC4PNHS140100 Q645 14G 10 100 50 3/8 500

TSWC4PNHS140115 Q650 14G 10 115 60 3/8 250

TSWC4PNHS140125 Q655 14G 10 125 60 3/8 250

TSWC4PNHS140150 Q660 14G 10 150 100 3/8 250

T17 HEX HEAD WITH SEAL / SCRATCHGUARD®AS3566 CLASS 4


(mm)

TSWC4PXHS120050 Q665 12G 11 50 35 5/16 1000

TSWC4PXHS120065 Q670 12G 11 65 35 5/16 1000

GRPX®

Flange Hex Type17 SDSClass 4


T17 PAN HEAD PHILLIPS AS3566 CLASS 2 (Zinc Yellow)


(mm)

TSWC2PPP#080016 QA16 8G 15 16 Full #2 1000

TSWC2PPP#080025 QA17 8G 15 25 Full #2 1000

T17 COUNTERSUNK HEAD PHILLIPS AS3566 CLASS 2 (Zinc Yellow)


(mm)

TSWC2PCP#060020 Q720 6G 18 20 Full #2 1000

TSWC2PCP#060030 Q723 6G 18 30 Full #2 1000

TSWC2PCP#080020 Q724 8G 15 20 Full #2 1000

TSWC2PCP#100030 Q728 10G 12 30 Full #2 1000

TSWC2PCP#100040 Q730 10G 12 40 Full #2 1000

T17 COUNTERSUNK HEAD PHILLIPS AS3566 CLASS 3


(mm)

TSWC3PCP#100030 Q737 10G 12 30 Full #2 1000

TSWC3PCP#100040 Q735 10G 12 40 Full #2 1000

T17 WAFER HEAD PHILLIPS AS3566 CLASS 3


(mm)

TSWC3PWP#100025 Q680 10G 12 25 Full #2 1000

TSWC3PWP#100035 Q682 10G 12 35 Full #2 1000

TSWC3PWP#100045 Q684 10G 12 45 Full #2 1000

Pan, CSK & Wafer Type17 SDSClass 2 / 3 / 4

TY

PE

17


COUNTERSUNK RIBBED HEAD PHILLIPS - CHIPBOARDAS3566 CLASS 1 (Zinc Yellow)


(mm)

TSDCYPRP#080020 Q002 8G 9 20 20 #2 1000

TSDCYPRP#080025 Q004 8G 9 25 25 #2 1000

TSDCYPRP#080028 Q006 8G 9 28 20 #2 1000

TSDCYPRP#080030 Q007 8G 9 30 20 #2 1000

TSDCYPRP#080032 Q008 8G 9 32 22 #2 1000

TSDCYPRP#080035 Q010 8G 9 35 24 #2 1000

TSDCYPRP#080041 Q012 8G 9 41 27 #2 1000

TSDCYPRP#080045 Q014 8G 9 45 30 #2 1000

TSDCYPRP#080051 Q016 8G 9 51 35 #2 1000

TSDCYPRP#080057 Q018 8G 9 57 39 #2 1000

TSDCYPRP#080065 Q019 8G 9 65 45 #2 500

TSDCYPRP#100040 Q021 10G 8 40 27 #2 1000

TSDCYPRP#100050 QA01 10G 8 50 35 #2 1000

TSDCYPRP#100065 Q020 10G 8 65 45 #2 500

TSDCYPRP#100075 Q022 10G 8 75 50 #2 500

TSDCYPRP#100100 Q024 10G 8 100 65 #2 500

T17 BUGLE BATTEN HEAD 6 RIBS AS3566 CLASS 3 (5mm Hex Drive)

Part QFind Size (TPI) Length Thread Int Hex Drive Pack

(mm) (mm)

TSWC3PBH#140050 Q700 14G 10 50 35 5 1000

TSWC3PBH#140065 Q701 14G 10 65 45 5 1000

TSWC3PBH#140075 Q702 14G 10 75 50 5 1000

TSWC3PBH#140100 Q704 14G 10 100 66 5 500

TSWC3PBH#140125 Q705 14G 10 125 80 5 250

TSWC3PBH#140150 Q706 14G 10 150 100 5 250

Bugle Batten Type17 SDSClass 1 / 3


SQUARE DRIVE BIT

Part QFind Length Thread Square Drive Pack

(mm)

TXDBQ#01 QD10 #1 x 25 100

TXDBQ#02 QD11 #2 x 25 100

TXDBQ#03 QD12 #3 x 25 100

COUNTERSUNK RIBBED HEAD SQUARE DRIVE AS3566 CLASS 3


(mm)

TSDC3PSQ#080020 Q026 8G 9 20 20 #2 1000

TSDC3PSQ#080025 Q028 8G 9 25 25 #2 1000

TSDC3PSQ#080032 Q032 8G 9 32 22 #2 1000

TSDC3PSQ#080035 Q034 8G 9 35 24 #2 1000

TSDC3PSQ#080041 Q036 8G 9 41 27 #2 1000

TSDC3PSQ#080045 Q038 8G 9 45 30 #2 1000

TSDC3PSQ#080051 Q040 8G 9 51 35 #2 1000

TSDC3PSQ#080057 Q042 8G 9 57 39 #2 1000

TSDC3PSQ#100060 Q043 10G 8 60 42 #2 1000

TSDC3PSQ#100065 Q044 10G 8 65 45 #2 500

TSDC3PSQ#100075 Q046 10G 8 75 50 #2 500

TSDC3PSQ#100100 Q048 10G 8 100 65 #2 500

TSDC3PSQ#100125 Q050 10G 8 125 75 #2 250

TSDC3PSQ#100150 Q055 10G 8 150 100 #2 250

CSK SDSClass 1 / 3

BUGLE HEAD NEEDLE POINT PHILLIPS AS3566 CLASS 1 (Zinc Yellow)


(mm)

TSNCYPBP#060020 Q080 6G 18 20 20 #2 1000

TSNCYPBP#060025 Q082 6G 18 25 25 #2 1000

TSNCYPBP#060032 Q086 6G 18 32 32 #2 1000

TSNCYPBP#060040 Q092 6G 18 40 40 #2 1000

TSNCYPBP#060045 Q094 6G 18 45 45 #2 1000

TSNCYPBP#060050 Q095 6G 18 50 50 #2 1000

TSNCYPBP#070020 Q097 7G 16 20 20 #2 1000

TSNCYPBP#070025 Q096 7G 16 25 25 #2 1000

TSNCYPBP#070030 Q098 7G 16 30 30 #2 1000

TSNCYPBP#070040 Q099 7G 16 40 40 #2 1000

TSNCYPBP#070045 Q100 7G 16 45 45 #2 1000

TSNCYPBP#070050 Q102 7G 16 50 50 #2 1000

NE

ED

LE P

OIN

T


HEX HEAD NEEDLE POINT / NO SEAL AS3566 CLASS 4


(mm)

TSNC4PFH#080012 Q148 8G 15 12 Full 1/4 1000

TSNC4PFH#100020 Q150 10G 12 20 Full 5/16 1000

HEX HEAD NEEDLE POINT / WITH SEAL AS3566 CLASS 4


(mm)

TSNC4PNH#080012 Q149 8G 15 12 Full 1/4 1000

TSNC4PNH#100020 Q151 10G 12 20 Full 5/16 1000

WAFER BUTTON HEAD NEEDLE POINT PHILLIPS AS3566 CLASS 3


(mm)

TSNC3PAP#080012 QA02 8G 15 12 Full #2 1000

TSNC3PAP#080016 Q141 8G 15 16 Full #2 1000

TSNC3PAP#080020 Q143 8G 15 20 Full #2 1000

TSNC3PAP#080025 Q145 8G 15 25 Full #2 1000

TSNC3PAP#080032 Q147 8G 15 32 Full #2 1000

TSNC3PAP#080040 QA04 8G 15 40 Full #2 1000

WAFER BUTTON HEAD NEEDLE POINT PHILLIPS AS3566 CLASS 2 (Zinc Yellow)


(mm)

TSNC2PAP#080012 Q138 8G 15 12 Full #2 1000

TSNC2PAP#080016 Q140 8G 15 16 Full #2 1000

TSNC2PAP#080020 Q142 8G 15 20 Full #2 1000

TSNC2PAP#080025 Q144 8G 15 25 Full #2 1000

TSNC2PAP#080032 Q146 8G 15 32 Full #2 1000

TSNC2PAP#080040 QA03 8G 15 40 Full #2 1000

NE

ED

LE P

OIN

T

Needle Point SDSClass 2 / 3 / 4


304 BUGLE BATTEN T17 WITH 4 RIBS HEX DRIVE (5mm)

Part QFind Size (TPI) Length Thread Int Hex Drive Pack

(mm)

TSW04BB#140035 QT33 14G 10 35 25 5mm 500

TSW04BB#140050 QT34 14G 10 50 33 5mm 500

TSW04BB#140065 QT35 14G 10 65 45 5mm 500

TSW04BB#140075 QT36 14G 10 75 50 5mm 500

TSW04BB#140100 QT38 14G 10 100 66 5mm 250

TSW04BB#140150 QT40 14G 10 150 100 5mm 200

304 TDX TRIM HEAD - SQUARE THREAD T17 WITH 4 RIBS SQUARE DRIVE


(mm)

TSW04TDX0050 QT42 10G 8 50 33 #1 1000

TSW04TDX0055 QT43 7G 10 55 40 #1 1000

TSW04TDX0065 QT44 10G 8 65 40 #1 1000

304 STA

INLE

SS

304 TRIM HEAD T17 WITH 6 RIBS SQUARE DRIVE


(mm)

TSW04TQ#080050 QT45 8G 10 50 33 #1 1000

304 COUNTERSUNK HEAD T17 WITH 6 RIBS SQUARE DRIVE


(mm)

TSW046Q#100050 QT30 10G 12 50 34 #2 1000

TSW046Q#100065 QT31 10G 12 65 43 #2 1000

Bugle, CSK & Trim SDS304 Stainless


304 COUNTERSUNK HEAD NEEDLE POINT WITH 4 RIBS SQUARE DRIVE


(mm)

TSN044Q#080020 QT10 8G 18 20 Full #2 1000

TSN044Q#080025 QT11 8G 10 25 Full #2 1000

TSN044Q#080032 QT12 8G 10 32 Full #2 1000

TSN044Q#080038 QT13 8G 10 38 25 #2 1000

TSN044Q#080042 QT14 8G 10 42 28 #2 1000

TSN044Q#080045 QT15 8G 10 45 30 #2 1000

TSN044Q#080050 QT16 8G 10 50 34 #2 1000

TSN044Q#100065 QT17 10G 8 65 43 #2 500

TSN044Q#100075 QT18 10G 8 75 50 #2 500

TSN044Q#100100 QT19 10G 8 100 65 #2 500

304 BUTTON HEAD NEEDLE SQUARE DRIVE


(mm)

TSN04BQ#080015 QT21 8G 15 15 13 #2 1000

TSN04BQ#080020 QT22 8G 15 20 18 #2 1000

TSN04BQ#080025 QT23 8G 15 25 23 #2 1000

316 BUTTON HEAD T17 SQUARE DRIVE


(mm)

TSW16BQ#100030 QT71 10G 12 30 20 #2 1000

TSW16BQ#100038 QT72 10G 12 38 25 #2 1000

TSW16BQ#100044 QT73 10G 12 44 29 #2 1000

TSW16BQ#100060 QT75 10G 12 60 40 #2 1000

Needle Point & Type17 SDS304 Stainless


T17 HEX HEAD / NO SEAL 316 STAINLESS AS3566


(mm)

TSW16PFH#120025 QT76 12G 11 25 25 5/16 1000

TSW16PFH#120050 QT77 12G 11 50 35 5/16 1000

TSW16PFH#120065 QT78 12G 11 65 43 5/16 1000

TSW16PFH#140025 QT79 14G 10 25 25 3/8 1000

TSW16PFH#140050 QT80 14G 10 50 37 3/8 1000

TSW16PFH#140065 QT81 14G 10 65 43 3/8 500

TSW16PFH#140075 QT82 14G 10 75 50 3/8 500

TSW16PFH#140090 QT83 14G 10 90 50 3/8 500

T17 HEX HEAD / WITH SEAL316 STAINLESS AS3566


(mm)

TSW16PNH#120025 QT84 12G 11 25 25 5/16 1000

TSW16PNH#120050 QT85 12G 11 50 35 5/16 1000

TSW16PNH#120065 QT86 12G 11 65 43 5/16 1000

TSW16PNH#140025 QT87 14G 10 25 25 3/8 1000

TSW16PNH#140050 QT88 14G 10 50 37 3/8 1000

TSW16PNH#140065 QT89 14G 10 65 43 3/8 500

TSW16PNH#140075 QT90 14G 10 75 50 3/8 500

TSW16PNH#140090 QT91 14G 10 90 50 3/8 500

316 STA

INLE

SS

Flange Hex Type 17 SDS316 Stainless


316 BUGLE BATTEN T17 WITH 4 RIBS SQUARE DRIVE


(mm)

TSW16BB#060025 QT46 6G 10 25 16 #1 100

TSW16BB#060032 QT47 6G 10 32 21 #1 100

TSW16BB#060038 QT48 6G 10 38 25 #1 100

TSW16BB#060050 QT50 6G 10 50 33 #1 100

TSW16BB#080025 QT51 8G 10 25 16 #2 100

TSW16BB#080032 QT52 8G 10 32 21 #2 100

TSW16BB#080038 QT53 8G 10 38 25 #2 100

TSW16BB#080050 QT55 8G 10 50 33 #2 100

TSW16BB#080058 QT56 8G 10 58 38 #2 100

TSW16BB#080065 QT57 8G 10 65 43 #2 100

TSW16BB#080075 QT58 8G 10 75 50 #2 100

TSW16BB#100050 QT59 10G 10 50 33 #2 100

TSW16BB#100058 QT60 10G 10 58 38 #2 100

TSW16BB#100065 QT61 10G 10 65 43 #2 100

TSW16BB#100075 QT62 10G 10 75 50 #2 100

TSW16BB#120058 QT63 12G 10 58 38 #3 100

TSW16BB#120065 QT64 12G 10 65 43 #3 100

TSW16BB#120075 QT65 12G 10 75 50 #3 100

TSW16BB#140050 QT66 14G 10 50 33 #3 100

TSW16BB#140058 QT67 14G 10 58 38 #3 100

TSW16BB#140065 QT68 14G 10 65 43 #3 100

TSW16BB#140075 QT69 14G 10 75 50 #3 100

TSW16BB#140100 QT70 14G 10 100 66 #3 50

Bugle Batten & Self Embed304 Stainless

316 SELF EMBEDDING HEAD T17 SQUARE DRIVE


(mm)

TSW16SQ#100040 QT92 10G 12 40 26 #2 1000

TSW16SQ#100050 QT93 10G 12 50 33 #2 1000

TSW16SQ#100065 QT94 10G 12 65 43 #2 500

TSW16SQ#100075 QT95 10G 12 75 50 #2 500

TSW16SQ#120130 QT96 12G 12 130 90 #3 250

TSW16SQ#120150 QT97 12G 12 150 100 #3 250

Since 1935 ...because quality matters

Terms and Conditions

The Company and the Customer each agree with the other as follows:DEFINITIONSCompany means Hobson Engineering Pty Limited (A.B.N. 38 000 289 958).Customer means the party described as the customer in the Delivery Docket as amended by the Invoice.Delivery Docket means the document furnished by the Company to the Customer.GST has the same meaning as given in A New Tax System (Goods and Services Tax) Act 1999 (“Act”).Invoice means a tax invoice (as defined in the Act) furnished by the Company to the Customer in respect of the product.Product means the goods described as the product in the Delivery Docket as amended by the Invoice.Purchase Order means the request by the Customer for the Product which is accepted by the Company.Sum means the price and other monies payable for the Product together with GST payable on the supply of the Product.SUPPLYThe Company supplies to the Customer the Product in accordance with these terms and conditions as varied in writing by the Company. Any variation in writing by the Company shall take precedence to these terms and conditions. We reserve the right to supply 316 stainless steel in lieu of 304 stainless steel.PRICEThe Sum is set forth in the Purchase Order as amended by the Invoice. The Customer agrees that the Sum set forth in the Purchase Order may be amended by the Invoice in respect of the following:arithmetic error; andGST payable on the supply of the Product not included or incorrectly calculated in the Sum.In addition to the price the Customer agrees, if so requested by the Company, to pay:any increase in any GST taxes and duties which the Company may be required to collect or pay in respect of the Product after the date of the Delivery Docket; andinterest accruing on a daily basis on the unpaid balance of the Sum from the due date for payment until actual receipt at the rate of 1 per cent per month.PAYMENTThe Customer must pay the Sum within 30 days of the end of the month in which the Product is delivered to the Customer unless otherwise determined by the Company.TITLE AND RISKNotwithstanding any other term and condition, the parties agree that the risk of the Product passes on delivery, but title to the Product does not pass until the Sum is paid in full. Until such time as the Sum is paid in full the Customer is only at liberty to sell the Product in the ordinary course of its business as agent for the Company on the condition that it holds on trust and accounts to the Company for the proceeds thereof. Pending the passing of title to the Product the Company may require the Customer to mark the Product as being the property of the Company.ACCEPTANCEThe initialling or signing of the Delivery Docket by the Customer or representative of the Customer shall constitute acceptance of the Product in accord with these terms and conditions.RETURNS AND ALLOWANCESThe Customer must satisfy itself within 14 days of the date of delivery of the Product with the type and quantity of the Product. In the event that the Customer considers it has not received the appropriate type and or quantity of Product it must notify the Company in writing within 14 days of the date of delivery of the Product. The notice must refer to the Delivery Docket number, the delivery date, the invoice number (if applicable) and provide adequate details of the incorrect type and or quantity of Product.As a consequence of this condition the receipt of Products by the Company, returned by the Customer does not constitute acceptance of the Product. Acceptance by the Company shall only be given by the Company, in writing, after the Product has been inspected and found satisfactory in the opinion of the Company. In the event that the Company does not accept the Product the Customer will be notified and the Product made available to the Customer. As a consequence of this condition no transport or freight costs shall be borne by the Company unless agreed to in writing by the Company.EXCLUSION OF WARRANTYNothing in this agreement excludes, restricts or modifies any condition, warranty or liability which may at any time be implied by the Trade Practices Act or Sales of Goods Act (NSW) or equivalent State or Territory legislation or any other law where to do so is illegal or would render any provision of this agreement void.Where the Company is responsible pursuant to the aforesaid condition warranty or liability which can not be excluded the parties agree that the Company shall only be liable for the cost of repair or the resupply of the Product. Subject to this condition any express or implied condition, statement or warranty (statutory or otherwise) in respect of the Product is expressly negated and excluded.GENERALThe validity, interpretation and performance of this agreement will be governed by and construed in accordance with the law of the State of New South Wales and of the Commonwealth of Australia which the parties acknowledge is the proper law of this agreement. Each of the parties irrevocably agrees that the Courts of the State of New South Wales and of the Commonwealth of Australia will have jurisdiction to hear and determine any suit, action or proceedings, and to settle any dispute, which may arise out of or in connection with this agreement and for this purpose irrevocably submits to the jurisdiction of such Courts. DISCOUNTS as advised are applicable to the prices shown in this price list.PRICES The resale prices or discounts referred to in the price list are recommended only and there is no obligation to comply with the recommendation. Prices are subject to GST where applicable.Minimum invoice value is $40.00SHIPPING QUANTITIES On specially manufactured items (± 10%).VALIDITY ON SPECIAL QUOTATIONS 14 days unless otherwise stated.© Copyright 2005 – No part of this catalogue may be published without the written consent of the publishers.

Note: Due to research and development, products are continually improved. This may lead to the specifications being changed without notice.

As part of our ongoing commitment to serve your fastener needs, please let us know if there are any products which we lack.

Also, if you’ve got any comments on this year’s Catalogue, let us know. We’ll consider your feedback when we produce next year’s. This catalogue is for you to use – so if it’s use can be made easier, then make sure you tell us! Our aim is to have the best catalogue possible as well as the best products.

Documents

Stock List 2012