Safety Technology International, Inc.2306 Airport Road
Waterford, Michigan 48327-1209Phone: 248-673-9898 Fax:
248-673-1246Toll Free: 800-888-4784 E-mail: [email protected]:
www.sti-usa.com
Safety Technology International (Europe) Ltd.Unit 49G Pipers
Road Park Farm Industrial Estate RedditchWorcestershire B98 0HU
England Tel: 44 (0) 1527 520 999Fax: 44 (0) 1527 501 999 Freephone:
0800 085 1678 (UK only)E-mail: [email protected] Web:
www.sti-europe.com
INSTALLATION OF SS-2000 FIRE SERIES STOPPER STATIONAll
specifications and information shown were current as of
publication, and are subject to change without notice. SHEET 1
10277IS JAN99
.69 in.(17mm)
SUB-102722-RPLASTIC SPACER MOLDEDIN RED (OPTIONAL)
TERMINAL BLOCK ASSEMBLY
BACKPLATE ASSEMBLYWITH STAINLESS STEELGROUND PLATE AND LUG
MOLDED BUTTONWITH KEY RESET
MOLDEDPOLYCARBONATEFACEPLATE
TURN CLOCKWISEONE QUARTER TURNTO RESET
19001 HOUSINGRETENTION SCREW#8-32 x 3/8 in.(1) PROVIDED
19015 3/32 in. ALLENWRENCH (1) PROVIDED
BUTTON LOCK NUT
FF II RREEP
U Sh
H E R E
STANDARD SINGLE OUTLET BOXNOTE: TO MOUNT STOPPER STATION
SS-2000F ON A STANDARD OUTLET BOX SUB-102722-R IS REQUIRED
19030 KEY(2) PROVIDED
10197H CONTACT HOLDER
SCREWS (2) PROVIDED19010 #6-32 x 1 in. WITHOUT SUB-102722-R19045
#6-22 x 1 1/2 in. WITH SUB-102722-R
TO PROVIDE ADEQUATECLEARANCE FOR INSTALLATIONTO ANY STANDARD
SINGLEGANG OUTLET BOX,THE SUB-102722-R SPACER IS REQ
2.25 in.(57mm)
1.62 in.(41mm)
4.87 in. (124mm)
3.25 in. (82mm)
PRODUCT DIMENSIONS
PRY BACK LEVER 'A' INDIRECTION OF ARROWTHEN USING A
FLATHEADSCREW DRIVER, INSERTAS SHOWN AND ROTATEUPWARD.
REMOVAL OF TERMINAL BLOCKS
A
INSERT TERMINALBLOCK NOTCH ASSHOWN AND ROTATEUPWARD.
INSTALLATION OF TERMINAL BLOCKS
ADAcompliant
Electronic warranty form at www.sti-usa.com/wc14
IF LASTSTATION ON
CIRCUIT,CONNECT E.O.L.
RESISTOR
12-18 AWG
CLOSE ONALARM
SINGLE DEVICE
DIAGRAM DEPICTINGMULTIPLE DEVICES
12-18 AWG
CLOSE ONALARM
SUPERVISED LOOP (SEE CAUTION NOTE)
CLOSE ONALARM
BE SURE ALL ELECTRICALPOWER IS DISCONNECTED
BEFORE STARTING THE INSTALLATION.NOTE: JUMPER NOT PROVIDED
AVIEW IN DIRECTIONS OF ARROWINSTALLATION AND REMOVAL OF TERMINAL
BLOCKS ANDTERMINAL BLOCK ASSEMBLY FROM BUTTON ASSEMBLY
TO SEPARATE TERMINALAND BUTTON ASSEMBLY
GRASP TERMINAL HOUSING, USINGTHUMB APPLY PRESSUREDOWNWARD,
REMOVE TERMINALHOUSING AS SHOWN.
REMOVAL OF TERMINAL BLOCKFROM TERMINAL HOUSING
INSERT SMALL SCREWDRIVERAS SHOWN AND PRYUPWARD, REMOVE
TERMINAL.
BACKPLATE ASSEMBLY
INSERT NOTCHAS SHOWN THENROTATE UPWARD
TERMINAL BLOCK RELEASE LEVERMUST FACE UPWARDAS SHOWN FOR
SWITCHTO FUNCTION CORRECTLY.
ELECTRICAL TERMINAL1, 2, OR 3 TERMINALSMAY BE USED
STRIP 1/4 in. OF WIRE INSULATION,INSERT IN TERMINAL (AS
SHOWN).THEN USING A PHILLIPS SCREWDRIVERTURN CLOCKWISE UNTIL
TIGHT.
AVIEW IN DIRECTIONS OF ARROWINSTALLATION OF ELECTRICALWIRE INTO
TERMINAL BLOCK
OUTGOING
INCOMING
BUTTON LOCK NUT
10196 N.O. TERMINAL BLOCK(2) PROVIDED UP TO 3TERMINALS MAY BE
USED FOREACH STATION ASSEMBLY.
A
AN UNINSULATED SECTION OF A SINGLECONDUCTOR SHOULD NOT BE
LOOPEDAROUND THE TERMINAL AND SERVE ASTWO CONNECTIONS.THE WIRE MUST
BE SEVERED, THEREBYPROVIDING SUPERVISION OF THECONNECTION IN THE
EVENT THE WIREBECOMES DISLODGED FROM THE DEVICE.
CAUTION
METAL WASHER
ALL TERMINALS ACCEPT TWO 12 TO 18 (AWG)
VOLTAGE RATED AVERAGE CURRENT
250 VDC 1 AMP24 VAC 3 AMP
SAFETY TECHNOLOGY INTERNATIONAL, INC. 2306 AIRPORT ROAD
WATERFORD MICHIGAN 48327-1209 PHONE: 248-673-9898 FAX: 248-673-1246
INFO @ www.sti-usa.comSHT. 2
10277IS JAN99
