Upload
nguyendang
View
217
Download
3
Embed Size (px)
Citation preview
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 1 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
• VIN 4.75V to 24V • Load current of up to 1.2A • Internal Power MOSFET • Stable with Low ESR Ceramic Output Capacitors • Up to 90% Efficiency • 0.1µA Shutdown Mode • Fixed 1.4MHz Frequency • Thermal Shutdown • Cycle-by-Cycle Over Current Protection • Resistor divider adjustable Output: 0.81V to 15V • SOT26: Available in “Green” Molding Compound
(no Br, Sb) • Lead Free Finish/RoHS Compliant (Note 1)
The AP5100 is a current mode step-down converter with a built-in power MOSFET to enable smallest solution size power conversion. With the low series resistance power switch it enables a constant output current of up to 1.2A over a wide input supply range. The load and line regulation has excellent response time over the operating input voltage and temperature range. The AP5100 is self protected, through a cycle-by-cycle current limiting algorithm and an on chip thermal protection. The AP5100 will provide the voltage conversion with a low count of widely available standard external components. The AP5100 is available in SOT26 package.
Applications
• Distributed Power Systems • Battery Charger • Pre-Regulator for Linear Regulators • WLED Drivers
Typical Applications
BST
SW
FB
IN
EN C2
AP5100R1
R2
D1
GND
VIN
C3 .L1C1
ONOFF
C6
5
4
1
6
3
VOUT
Figure 1. Typical Application Circuit
Features General Description
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 2 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
Typical Applications (Continued)
BST
SW
FB
IN
ENC2
22µF6.3V
R3100kohm AP5100
R149.9kohm
R216.2kohm
D1B230A
GND
VIN
VOUT
3.3V
C322nF
3.3µHC1
10µF25V
ONOFF
C6100pF
5
4
1
6
3
L1
Figure 2. 1.4MHz, 3.3V Output at 1A Step-Down Converter
BST
SW
FB
IN
EN
C210µF16V
R3100Kohm
AP5100
R240 ohm
1%
1N5819HW-7
GND
VINC3
10nFL1
10µHC110µF25V
ONOFF
5
4
1
6
3
6V -12V
- Vout
- Vout
- Vout - Vout
LED1
LED 2
LED 3R4200Kohm
1%
D1
Figure 3. White LED Driver Application
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 3 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
AP5100 W G - 7
Package PackingGreen
G : GreenW : SOT26 7 : Tape & Reel
Device Package
Code Packaging
(Note 2) 7” Tape and Reel
Quantity Part Number Suffix AP5100WG-7 W SOT26 3000/Tape & Reel -7
Notes: 1. EU Directive 2002/95/EC (RoHS). All applicable RoHS exemptions applied. Please visit our website at http://www.diodes.com/products/lead_free.html. 2. Pad layout as shown on Diodes Inc. suggested pad layout document AP02001, which can be found on our website at
http://www.diodes.com/datasheets/ap02001.pdf. Pin Assignments
1
2
3 74
6
EN
GND IN
FB
SOT26
5
BST
( Top View )
SW
Ordering Information
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 4 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
Pin Descriptions
Pin Name Pin # Description
BST 1 Bootstrap. To form a boost circuit, a capacitor is connected between SW and BST pins to form a floating supply across the power switch driver. This capacitor is needed to drive the power switch’s gate above the supply voltage. Typical values for CBST range from 0.1uF to 1uF.
GND 2 Ground. This pin is the voltage reference for the regulated output voltage. All control circuits are referenced to this pin. For this reason care must be taken in its layout.
FB 3 Feedback. To set the output voltage, connect this pin to the output resistor divider or directly to VOUT. To prevent current limit run away during a current limit condition, the frequency foldback comparator lowers the oscillator frequency when the FB voltage is below 400mV.
EN 4 On/Off Control Input. Do not leave this pin floating. To turn the device ON, pull EN above 1.2V and to turn it off pull below 0.4V. If enable/disable is not used, connect a 100kOhm resistor between EN to VIN.
IN 5 Supply Voltage. The AP5100 operates from a +4.75V to +24V unregulated input. A decoupling capacitor C1 is required to prevent large voltage spikes from appearing at the input. Place this capacitor near the IC.
SW 6 Switch Output. This is the reference for the floating top gate driver.
Absolute Maximum Ratings (Note 3)
Symbol Description Rating Unit
ESD HBM Human Body Model ESD Protection 3 KV ESD MM Machine Model ESD Protection 300 V
VIN Supply Voltage 26 V VSW Switch Voltage -0.3 to VIN + 0.3 V
VBST Boost Voltage VSW + 6 V All Other Pins –0.3 to +6 V
TST Storage Temperature -65 to +150 °C TJ Junction Temperature +150 °C TL Lead Temperature +260 °C θJA Junction to Ambient Thermal Resistance (Note 4) 140 °C/W θJC Junction to Case Thermal Resistance (Note 4) 35 °C/W
Notes: 3. Exceeding these ratings may damage the device. 4. Test condition for SOT26: Measured on approximately 1” square of 1 oz copper.
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 5 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
Recommended Operating Ratings (Note 5)
Symbol Description Rating Unit
VIN Supply Voltage 4.75 to 24 °C TA Operating Ambient Temperature Range -25 to +85 °C
VOUT Output Voltage 0.81 to 15 V Notes: 5. The device function is not guaranteed outside of the recommended operating conditions.
Electrical Characteristics ( VIN = 12V, TA = +25°C, unless otherwise noted)
Notes: 6. Guaranteed by design.
Symbol Parameter Test Conditions Min Typ. Max Unit VFB Feedback Voltage 4.75V ≤ VIN ≤ 24V 0.790 0.810 0.830 V IFB Feedback Current VFB = 0.8V 0.1 µA
RDS(ON) Switch-On Resistance (Note 6) 0.35 Ω Switch Leakage VEN = 0V, VSW = 0V 10 µA Current Limit (Note 6) 2.4 A
fSW Oscillator Frequency VFB = 0.6V 1.1 1.4 1.7 MHz Fold-back Frequency VFB = 0V 480 kHz Maximum Duty Cycle VFB = 0.6V 87 %
tON Minimum On-Time (Note 6) 100 ns Under Voltage Lockout Threshold
Rising 3.8 4.0 4.2 V
Under Voltage Lockout Threshold Hysteresis 150 mV
EN Input Low Voltage 0.4 V EN Input High Voltage 1.2 V
EN Input Current VEN = 2V 0.3
µA VEN = 0V 0.1
IS Supply Current (Shutdown) VEN = 0V 0.1 1.0 µA IQ Supply Current (Quiescent) VEN = 2V, VFB = 1V 0.4 1.0 mA Thermal Shutdown (Note 6) 140 °C
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 6 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
Typical Performance Characteristics
VIN=12V, VOUT =3.3V, L=3.3uH, C1=10uF, C2=22uF, TA=+25•C, unless otherwise noted.
Steady State Test
(IOUT=0.5A) Load Transient Test
(IOUT=0.2A to 0.8A. Step at 0.8A/us)
Time- 1us/div
Time- 100us/div
Start-up Through Enable(No Load)
Start-up through Enable (IOUT=1A, resistive load)
Time- 50us/div
Time- 50us/div
Shutdown Through Enable(No Load)
Shutdown Through Enable (IOUT=1A, resistive load)
Time- 50us/div
Time- 50us/div
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 7 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
Typical Performance Characteristics (Continued)
Short Circuit Entry Short Circuit Recovery
Time- 50us/div
Time- 100us/div
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 8 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
Application Information
OPERATION The AP5100 is a current mode control, asynchronous buck regulator. Current mode control assures excellent line and load regulation and a wide loop bandwidth for fast response to load transients. Figure. 4 depicts the functional block diagram of AP5100. The operation of one switching cycle can be explained as follows. At the beginning of each cycle, HS (high-side) MOSFET is off. The EA output voltage is higher than the current sense amplifier output, and the current comparator’s output is low. The rising edge of the 1.4MHz oscillator clock signal sets the RS Flip-Flop. Its output turns on HS MOSFET. When the HS MOSFET is on, inductor current starts to increase. The Current Sense Amplifier senses and amplifies the inductor current. Since the current mode control is subject to sub-harmonic oscillations that peak
at half the switching frequency, Ramp slope compensation is utilized. This will help to stabilize the power supply. This Ramp compensation is summed to the Current Sense Amplifier output and compared to the Error Amplifier output by the PWM Comparator. When the sum of the Current Sense Amplifier output and the Slope Compensation signal exceeds the EA output voltage, the RS Flip-Flop is reset and HS MOSFET is turned off. The external Schottky rectifier diode (D1) conducts the inductor current. For one whole cycle, if the sum of the Current Sense Amplifier output and the Slope Compensation signal does not exceed the EA output, then the falling edge of the oscillator clock resets the Flip-Flop. The output of the Error Amplifier increases when feedback voltage (VFB) is lower than the reference voltage of 0.81V. This also increases the inductor current as it is proportional to the EA voltage.
Figure 4. Functional Block Diagram
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 9 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
Application Information (Continued)
Setting the Output Voltage The output voltage can be adjusted from 0.81V to 15V using an external resistor divider. Table 1 shows a list of resistor selection for common output voltages. Resistor R1 is selected based on a design tradeoff between efficiency and output voltage accuracy. For high values of R1 there is less current consumption in the feedback network. However the trade off is output voltage accuracy due to the bias current in the error amplifier. R2 can be determined by the following equation:
⎟⎟⎠
⎞⎜⎜⎝
⎛−×= 1
0.81OUTV
2R1R
VOUT (V) R1 (kΩ) R2 (kΩ)
1.8 80.6 (1%) 64.9 (1%)
2.5 49.9 (1%) 23.7 (1%)
3.3 49.9 (1%) 16.2 (1%)
5 49.9 (1%) 9.53 (1%)
Table 1. Resistor Selection for Common Output Voltages
Inductor Calculating the inductor value is a critical factor in designing a buck converter. For most designs, the following equation can be used to calculate the inductor value;
SWfLΔIINV)OUTVIN(VOUTV
L××−×
=
Where LΔI is the inductor ripple current.
And SWf is the buck converter switching frequency. Choose the inductor ripple current to be 30% of the maximum load current. The maximum inductor peak current is calculated from:
2LΔI
LOADIL(MAX)I +=
Peak current determines the required saturation current rating, which influences the size of the inductor. Saturating the inductor decreases the converter efficiency while increasing the temperatures of the inductor, the MOSFET and the diode. Hence choosing an inductor with appropriate saturation current rating is important. A 1µH to 10µH inductor with a DC current rating of at least 25% percent higher than the maximum load current is recommended for most applications. For highest efficiency, the inductor’s DC resistance should be less than 200mΩ. Use a larger inductance for improved efficiency under light load conditions. Input Capacitor The input capacitor reduces the surge current drawn from the input supply and the switching noise from the device. The input capacitor has to sustain the ripple current produced during the on time on the upper MOSFET. It must hence have a low ESR to minimize the losses. Due to large dI/dt through the input capacitors, electrolytic or ceramics should be used. If a tantalum must be used, it must be surge protected. Otherwise, capacitor failure could occur. For most applications, a 4.7µF ceramic capacitor is sufficient. Output Capacitor The output capacitor keeps the output voltage ripple small, ensures feedback loop stability and reduces the overshoot of the output voltage. The output capacitor is a basic component for the fast response of the power supply. In fact, during load transient, for the first few microseconds it supplies the current to the load. The converter recognizes the load transient and sets the duty cycle to maximum, but the current slope is limited by the inductor value. Maximum capacitance required can be calculated from the following equation:
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 10 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
2OUTV2)OUTV V(Δ
2)2
inductorΔIOUTL(I
oC−+
+=
Where ΔV is the maximum output voltage overshoot. ESR of the output capacitor dominates the output voltage ripple. The amount of ripple can be calculated from the equation below:
ESRinductorΔIcapacitorVout ×=
An output capacitor with ample capacitance and low ESR is the best option. For most applications, a 22µF ceramic capacitor will be sufficient. External Diode The external diode’s forward current must not exceed the maximum output current. Since power dissipation is a critical factor when choosing a diode, it can be calculated from the equation below:
0.3VoutI)INV
OUTV(1diodeP ××−=
Note: 0.3V is the voltage drop across the schottky diode. A diode that can withstand this power dissipation must be chosen. PC Board Layout This is a high switching frequency converter. Hence attention must be paid to the switching currents interference in the layout. Switching current from one power device to another can generate voltage transients across the impedances of the interconnecting bond wires and circuit traces. These interconnecting impedances should be minimized by using wide, short printed circuit traces. The input capacitor needs to be as close as possible to the IN and GND pins. The external feedback resistors should be placed next to the FB pin.
External Bootstrap Diode It is recommended that an external bootstrap diode be added when the input voltage is no greater than 5V or the 5V rail is available in the system. This helps improve the efficiency of the regulator. The bootstrap diode can be a low cost one such as IN4148 or BAT54.
AP5100
BST
SW
10nF
BOOST DIODE
5V
1
6
Figure 5. External Bootstrap Diode
Application Information (Continued)
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 Rev. 1 11 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
Marking Information (1) SOT26
1 2 3
6 74XX : Identification Code Y : Year 0~9
X : A~Z : Green
( Top View )5
W : Week : A~Z : 1~26 week;a~z : 27~52 week; z represents52 and 53 week
XX Y W X
Part Number Package Identification Code AP5100W SOT26 AJ
Package Information (All Dimensions in mm)
(1) Package type: SOT26
AP51001.2A Step-Down Converter with 1.4MHz Switching
Frequency
AP5100 Rev. 1 12 of 12 MARCH 2010 Document number: DS32130 Rev. 1 - 2 www.diodes.com © Diodes Incorporated
IMPORTANT NOTICE DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION). Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated website, harmless against all damages. Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel. Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized application. Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings noted herein may also be covered by one or more United States, international or foreign trademarks.
LIFE SUPPORT Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: 1. are intended to implant into the body, or
2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in significant injury to the user.
B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected
to cause the failure of the life support device or to affect its safety or effectiveness. Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems. Copyright © 2010, Diodes Incorporated www.diodes.com