STANDARD OPERATING PROCEDURE For MIKROTIK ...cbc2home.it.msd.net.my/manual/pi1m/Pi1M SOP Mikrotik...Mikrotik Router Configuration Setting IP Addressing 1. Click on IP > Addresses 2

MSD DIGITAL INTELLIGENCE SDN.BHD.

STANDARD OPERATING PROCEDURE

For

MIKROTIK ROUTERBOARD RB1100AH

This document has been prepared for the Customer's sole and

exclusive information and use and may not be made available to

any third parties except with MSD’s written consent.

© MSD Digital Intelligence Sdn. Bhd Standard Operating Procedure (SOP)

Pi1M- SOP-MIKROTIK RB1100AH-1.0

© 2012 MSD Digital Intelligence Sdn. Bhd., Selangor.

Company Number: 761551 - T

All rights reserved. No part of this publication may be reprinted, reproduced, stored in a

retrieval system or transmitted, in any form or by any means, without the prior

permission in writing from the owners.

First published and distributed in Nov, 2012.



The device used

1. >2 unit PC

2. ≥ 1 Router RB1100AH

3. >1 unit Network (Ethernet) cable 8p8c

4. Power Cable

Discussed in this guide

1. Mikrotik Configuration reset

2. Mikrotik CBC & KTW Configuration

3. Connection Test

Pre-Configure Laptop

1. Download winbox.exe from Mikrotik (http://download2.mikrotik.com/winbox.exe)

2. Disable wireless interface and firewall.

http://download2.mikrotik.com/winbox.exe



3. Set Laptop to static IP TCP/IPv4 (Subject to change)

Set – 172.16.200.2 as Laptop IP Address

Set – 255.255.255.252 as Subnet Mask

Set – 172.16.200.1 as Default Gateway

Set – 172.16.200.1 as DNS



Mikrotik Configuration reset

1. Plug in network cable from laptop and router port ETH 1 (any port will do)

2. Run winbox.exe and connect to router using MAC Address

3. Click on New Terminal

4. Type ‘system reset’

5. Type ‘y’

6. Exit winbox



Mikrotik Router Configuration

Setting IP Addressing

1. Click on IP > Addresses

2. Refer IP address from IP Address Assignment document. (e.g.: Felda Mempaga 3)

(10.16.9.1 – 10.16.10.254)

a. Set Router Ether1 Address to 172.16.200.1/30 (VSAT)

(Subject to change)

Default Configuration

Change Ether1 ip address = 172.16.200.1/30



b. Set Router Ether2 Address to 10.16.9.1/24 (CBC)

(DHCP Range 100-150)

*Repeat IP addressing Process up till ether 7

c. Set Router Ether3 Address to 10.16.10.1/26 (Switch Connection)

(DHCP Range 5-62)

d. Set Router Ether4 Address to 10.16.10.65/27 (Sub Node 1)

(DHCP Range 69-94)

e. Set Router Ether5 Address to 10.16.10.97/27 (Sub Node 2)


f. Set Router Ether6 Address to 10.16.10.129/27 (Sub Node 3)


g. Set Router Ether7 Address to 10.16.10.161/27 (Sub Node 4)




Final IP addressing Configuration



Setting DHCP Range

1. Click on IP > DHCP Server

2. Click DHCP Setup

Interface

DHCP Range

Ether2 10.16.9.100 – 10.16.9.150

Ether3 10.16.10.5 - 10.16.10.62

Ether4 10.16.10.69 - 10.16.10.94

Ether5 10.16.10.101 - 10.16.10.126

Ether6 10.16.10.133 - 10.16.10.158

Ether7 10.16.10.165 - 10.16.10.190

Select interface

Set DHCP Address Space



Setup Gateway for DHCP Network

Set DHCP Range for each interface

DNS Server (172.16.200.1)

Set Lease Time to 1 hour



*Repeat DHCP Range Process up till ether 7

Final DHCP Range table



Connection Test

1. Disable PC/Laptop wireless & firewall

2. Connect Ether2 to PC/Laptop with automatic IP Obtaining.

3. On PC/Laptop run command prompt

a. Windows = Start>run> type “cmd” > hit Enter

4. Ping laptop 172.16.200.2

5. Repeat step 2 to 4 on all other Ethernet port and ip address connected to router.

Documents

STANDARD OPERATING PROCEDURE For MIKROTIK ...cbc2home.it.msd.net.my/manual/pi1m/Pi1M SOP Mikrotik...Mikrotik Router Configuration Setting IP Addressing 1. Click on IP > Addresses 2