St. Joseph's HospitalClinic Research Expansion240 W. Thomas Rd. Phoenix, AZ 85013

Plumbing ContractorRKS Plumbing & Mechanical, Inc.

23659 N. 35th DriveGlendale, AZ 85310

(602) 996-1866(602) 996-1816 - Fax

Operation & MaintenanceGeneral Contractor

Kitchell Contractors , Inc.1707 E. Highland Ave.

Phoenix, AZ 85016602.264.4411

Architect Archsol LLC8901 E. Pima Center Parkway Suite 205Scottsdale, AZ 85258480.471.8267

EngineerBridgers & Paxton Consulting Engineers11209 N. Tatum Blvd. Suite 160Phoenix, AZ 85028602.996.6399

RKS JOB No. 2014-167January 30, 2015

P-1

N73© 2014 AS America Inc. 7/14

MADERA™ FloWise® 16-1/2" HIGH 1.28 GPF FLUSHOMETER TOILET SYSTEM

with EVERCLEAN®

SELECTRONIC® EXPOSED AC FLUSH VALVE

MADERA™ FloWise® 16-1/2" HIGH 1.28 GPF FLUSHOMETER TOILET SYSTEM with EVERCLEAN®

❏ 3461.712 1.28 gpf 16-1/2" High Top Spud Bowl and Selectronic® Exposed AC Flush Valve

BOWL: •Floormountelongatedflushometervalvetoilet •Vitreouschina •HighEfficiency.Operatesintherangeof1.1gpfto

1.6 gpf (4.2 Lpf to 6.0 Lpf) •PermanentEverClean® surface inhibits the growth

ofstain-andodor-causingbacteria,mold,andmildew on the surface

•16-1/2"rimheightforaccessibleapplication •Powerfuldirect-fedsiphonjetaction •Fullyglazed2-1/8"trapway •Condensationchannel •10"or12"rough-in •10"x12"watersurfacearea •1-1/2"inletspud •100%factoryflushtested •Lesstoiletseat •Model3461.001

SELECTRONIC® FLUSH VALVE: •ElectronicflushvalvewithSelectronic®proximity

systemforhygienic"HandsFree"operation •Self-CleaningPistonwithintegralwiperspringhelps

preventcloggingandreducesmaintenance •Pistonoperationdeliverssuperiorflushaccuracy

andrepeatability •FullyMechanicalManualOverride-allowsvalveto

flushduringapowerfailure •Fail-SafeOperation-valveautomaticallycloses,

and does not need to be reset, on loss of power or water pressure

•AdjustableSanitaryFlush:Valvecanbeprogrammed toopenafterapre-programmedperiodofnon-use

•ChemicalresistantEPDMsealsareunaffected bychloramines

•Sensor&electroniccontrolsarefullyenclosedand water resistant

•Rangecanbeadjustedmanuallyorwithoptional remotecontrol

•IncludesULapprovedhardwiredACtransformer •InputVoltage:100-250VAC,50/60Hz.Output

Voltage:6VDC •Adjustabletailpieceforrough-inflexibility •Canbeinstalledleftorrighthand •Model6067.121

Includes:•047007-0070AInletSpud(furnishedwithbowl)•481310-1002Boltcapswithretainers(furnished

with bowl)•Inletincludes1"I.P.S.anglestopwithback-flow

protection, and vandal-resistant cap •1"Sweatsolderkit,covertubeandwallflange•Outletincludes1-1/2"vacuumbreaker

withspudcouplingandflange

BARRIER FREE

High-Efficiency Toilet System •20%watersavingswhencomparedto1.6gpf toiletsystemsSystem MaP* Score: • 1,000gramsofmiso@1.28gpf * MaximumPerformance(MaP)testingperformedby

IAPMOR&TLab.MaPReportconductedbyVeritec Consulting,Inc.andKoellerandCompany.

Operating Pressure:OverallRange:20-125psi**Recommended:25psi(flowing)-80psi(static)**Waterpressureover80psiisnotrecommended

formostplumbingfixtures.

Flow Requirement:25gpm(94.6L/min.)

Nominal Fixture Dimensions:718x356x419mm(28-1/4"x14"x16-1/2")

To Be Specified:❏Color:❏White❏ Seat: ❏AmericanStandard#5901.100

Heavydutyopenfrontlesscover ❏AmericanStandard#5905.100

Extraheavydutyopenfrontlesscover

SEEREVERSEFORROUGHING-INDIMENSIONS

Am

erican Stand

ard W

arranties

Warranties

D-IPricing Guide 2012

AS AMERICA, INC. ONE YEAR LIMITED WARRANTYIf inspection of this AS America, Inc. (“American Standard”) plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.

This limited warranty applies only to the original purchaser and installation of these products. In the event of a limited warranty claim, proof of purchase will be required—save sales receipt.

This limited warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation.

This limited warranty is void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damages; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American Standard.

American Standard's option to repair or exchange the product under this limited warranty does not cover any labor or other costs of removal or installation. IN NO EVENT WILL AMERICAN STANDARD BE LIABLE FOR THE COST OF REPAIR OR REPLACEMENT OF ANY INSTALLATION MATERIALS, INCLUDING BUT NOT LIMITED TO, TILES, MARBLE, ETC. American Standard will not be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this limited warranty. This limited warranty does not cover any liability for consequential or incidental damages, all of which are hereby expressly disclaimed, or the extension beyond the duration of this limited warranty of any implied limited warranties, including those of merchantability or fitness for an intended purpose. (Some states or provinces do not allow the exclusion or limitation of implied limited warranties, so this exclusion may not apply to you.)

This limited warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this limited warranty does not affect such statutory rights.

AS AMERICA, INC. LIMITED WARRANTY FORLXP, BOULEVARD® DUAL FLUSH, CHAMPION® PRO, CHAMPION®4, TITAN® PRO TOILETS

This toilet comes with a limited lifetime warranty on chinaware, a limited 10 year warranty on all mechanical parts of the toilet, and a limited 1 year warranty on the toilet seat if included with product. If inspection of this AS America, Inc. (“American Standard”) plumbing product, inclusive of the chinaware and all mechanical parts, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for the same or a similar model.

This limited warranty applies only to the original non-commercial purchaser and installation of the products. In the event of a limited warranty claim, proof of purchase will be required – save sales receipts.

For this warranty to become effective, the warranty registration process must be completed via the internet or telephone per the warranty registration instructions.

This limited warranty does not apply to commercial installations.  The warranty for commercial installations is 10 years on chinaware and mechanical parts, and 1 year on the toilet seat if included with product.

This warranty does not apply to local building code compliance. Since local building codes vary considerably, the purchaser of the product should check with a local building or plumbing contractor to ensure local code compliance before installation.

This warranty will be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American Standard’s instructions; or if it has been modified in a manner inconsistent with the product as shipped by American Standard.

WARNING: This warranty DOES NOT COVER any damages caused by the use of in-tank cleaners. These products can seriously corrode the fittings in the tank. This damage can cause leakage and property damage. American Standard will not be responsible or liable for any damage caused by the use of in-tank cleaners.

American Standard’s option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation including any costs of any surrounding material such as tile or marble.  American Standard is not responsible for any other incidental or consequential damages attributed to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)

This warranty gives you specific rights. You may have other statutory rights that may vary from state to state or province to province, in which case this warranty does not affect such statutory rights.

Royal®

Flushometer

Repair Parts and Maintenance Guide

2.1.1

PARTS LISTItemNo. Code No. Part No. Description

1. 0301172 A-72 CP Cover2. 0301168 A-71 Inside Cover3. — Dual Filtered Diaphragm™ Assembly

(refer to table and diagram on following page)4. 0302390 B-73-A CP ADA-Compliant Triple Seal Handle Assembly5. 0301082 A-6 CP Handle Coupling6. 0302109 B-7-A CP Socket Assembly7. 0302389 B-74-A CP ADA-Compliant Handle 8. 3302306 B-51-A Triple Seal Handle Repair Kit9. 5301139 A-31 Handle Gasket – 48 per package

10. 0306125 F-5-AW 3/4” (19 mm) CP Spud Coupling Assembly0306140 F-5-AU 1-1/4” (32 mm) CP Spud Coupling Assembly0306146 F-5-AT 1-1/2” (38 mm) CP Spud Coupling Assembly

11. 3323182 V-651-A High Back Pressure Vacuum Breaker Repair Kit12. 3393004 V-600-AA 3/4” (19 mm) x 9” (228 mm) CP Vacuum Breaker

3393006 V-600-AA 1-1/4” (32 mm) x 9” (228 mm) CP Vacuum Breaker3393007 V-600-AA 1-1/2” (38 mm) x 9” (228 mm) CP Vacuum Breaker

13. 0308676 H-550 CP Stop Coupling14. 0308801 H-551-A CP Adjustable Tailpiece 2-1/16” (52 mm long)

Standard Length*15A. 5308696 H-553 O-ring – 24 per package15B. 5308381 H-552 Locking Ring – 12 per package16. 3308386 H-700-A 1” (25 mm) CP Bak-Chek® Screwdriver Stop

3308384 H-700-A 3/4” (19 mm) CP Bak-Chek® Screwdriver Stop17. 3308853 H-541-ASD Control Stop Repair Kit †

3308856 H-543-ASD Control Stop Repair Kit ‡

18. 0308612 H-622 CP Bonnet †

0308843 H-577 CP Bonnet ‡

19. 3308772 H-1010-A Vandal Resistant Control Stop Cap Assembly †

3308790 H-1009-A Vandal Resistant Control Stop Cap Assembly ‡

20. 0308738 H-573 Control Stop Cap CP †

0308848 H-582 Control Stop Cap CP ‡

21. 3308866 H-574 Control Stop Cap with Bumper †

(–YO Variation)22. 3308867 H-576 Control Stop Cap with Extended Bumper †

(–YG Variation)* See page 4.2.1 for additional lengths† For use with 1” and 3/4” H-700-A and 1” H-600-A Bak-Chek® screwdriver control stop‡ For use with 3/4" H-600-A Bak-Chek® screwdriver control stop

Sloan products are also available in satin, brushed nickel, chrome, gold and polished brass finishes – contactfactory for part numbers.

TAILPIECES, CONTROL STOPS AND FLUSH CONNECTIONSFor additional information on tailpieces, control stops and flushconnections see Section 4.

tailpiece

control stop and caps

Valve Body(not sold separately)

082009

Repair Parts and Maintenance Guide

2.1.2

102008

Royal®

Flushometer

ROYAL® PERFORMANCE KITRelief Refill Flow

Code No. Part No. Description Valve† Head* Ring3301070 A-1101-A Low Consumption Water Closets-1.6 gpf (6.0 Lpf) Green Gray Smooth3301071 A-1102-A Water Saver Water Closets-3.5 gpf (13.2 Lpf) White Gray Smooth3301072 A-1103-A 9 Liter European Water Closets-2.4 gpf (9.0 Lpf) Blue Gray Smooth3301073 A-1106-A Wash Down Urinals-0.5 gpf (1.9 Lpf) Green Black Smooth & Slotted3301074 A-1107-A Low Consumption Urinals-1.0 gpf (3.8 Lpf) Green Black Slotted3301075 A-1108-A Water Saver Urinals-1.5 gpf (5.7 Lpf) Black Black Smooth*Closet refill heads (gray) have larger slots than urinal refill heads (black).

DIAPHRAGM ONLY KITRelief Refill Flow

Code No. Part No. Description Valve† Head* Ring3301502 A-1041-A Low Consumption Water Closets-1.6 gpf (6.0 Lpf) Green Gray Smooth3301501 A-1038-A Water Saver Water Closets-3.5 gpf (13.2 Lpf) White Gray Smooth3301505 A-1044-A 9 Liter European Water Closets-2.4 gpf (9.0 Lpf) Blue Gray Smooth3301504 A-1043-A Wash Down Urinals-0.5 gpf (1.9 Lpf) Green Black Smooth & Slotted3301503 A-1042-A Low Consumption Urinals-1.0 gpf (3.8 Lpf) Green Black Slotted3301500 A-1037-A Water Saver Urinals-1.5 gpf (5.7 Lpf) Black Black Smooth3301506 A-1045-A High-Efficiency Water Closets-1.28 gpf (4.8 Lpf) Blue Gray Smooth† Consult factory for availability of replacement plastic relief valves (green, black, blue, and white) and brass relief valves.NOTE: For older water closets that require 4.5 gpf (17.0 Lpf), choose kits A-1102-A or A-1038-A, but remove the flow ring before use. For blowout-style urinals that require 3.5 gpf (13.2 Lpf),choose kits A-1102-A or A-1038-A. For service sinks that require 6.5 gpf (24.6 Lpf), order A-36-A diaphragm repair kit (not shown Sloan Code No. 3301036) and remove the flow ring beforeuse. Regulations for low consumption fixtures prohibit the use of higher flush volumes.

*Closet refill heads (gray) have larger slots than urinal refill Heads (black).

The colors of the relief valve andthe refill head plus the shape offlow ring identify the flush volumeof a DUAL FILTERED DIAPHRAGMASSEMBLY.

DUAL FILTERED DIAPHRAGM™ ASSEMBLYAvailable in diaphragm only and Royal® Performance™ Kits.

Royal® Performance™ Kit includes dual filtered diaphragm assembly (item 3),handle repair kit with triple seal packing (item 8), high back pressurevacuum breaker repair kit (item 11), and one tailpiece O-ring (item 15A).DIAPHRAGM ONLY KIT contains “drop-in” dual filtered diaphragm assembly(item 3) ONLY.

The dual filtered diaphragm can be used in Royal,® Regal,® and similardiaphragm-style valve bodies. For use in Sloan valve bodies with a bell-shaped cover (manufactured before 1964), replace the bottom filter ring inthese kits with a blue A-108 filter ring (not shown Sloan Code No. 5301283).

NOTE: In January 1998, the Royal ® diaphragm design was upgraded to apreassembled unit with two (2) plastic filtering rings attached to the rubber diaphragm(one on top and one on bottom). If the Flushometer you are servicing has our older,segmented diaphragm with brass by-pass hole, refer to our Regal section foradditional troubleshooting information.

COVER

BODY

HANDLE COUPLING

HANDLE ASSEMBLY

FLUSH CONNECTION(VACUUM BREAKER)

SPUD COUPLING

STOPCOUPLING

CONTROLSTOP

SUPPLYFLANGE

TAILPIECE

OUTLET COUPLING

SPUD FLANGE

Royal®

Flushometer

Repair Parts and Maintenance Guide

2.1.3

062006

ATTENTION INSTALLERS: With the exception of the control stop inlet, DO NOT USE pipe sealant or plumbing grease on any valve component orcoupling! To protect the chrome or special finish of Sloan Flushometers, DO NOT USE toothed tools to install or service these valves. Use our A-50Super-Wrench™ or other smooth-jawed wrench to secure couplings.Regulations for low consumption fixtures (1.6 gpf/6.0 Lpf closets and 1.0 gpf/3.8 Lpf urinals) prohibit use of higher flush volumes.

1. Flushometer does not function (no flush).A. Control stop or main supply valve is closed. Open control stop or main

supply valve.

B. Handle assembly is damaged. Replace B-73-A handle or repair withB-51-A handle repair kit.

C. Relief valve is damaged. Replace relief valve.

2. Handle leaks.A. Handle seal or handle assembly is damaged. Replace B-73-A handle

or repair with B-51-A handle repair kit.

3. Water splashes from fixture.A. Control stop is open wider than necessary. Adjust control stop for

desired delivery of water volume.

B. Water saver/conventional diaphragm assembly is installed on lowconsumption fixture or closet diaphragm assembly is installed onurinal fixture. Determine the required flush volume (see label on valveor markings on fixture). Replace diaphragm assembly or relief valvefor appropriate flush volume of fixture.

4. Volume of water is insufficient to adequately siphon fixture.A. Control stop is not open wide enough. Adjust control stop for desired

delivery of water volume.

B. Diaphragm assembly is damaged. Replace diaphragm assembly.

C. Low consumption diaphragm assembly is installed on watersaver/conventional fixture or urinal diaphragm assembly is installedon closet fixture. Determine the required flush volume (see label onvalve or markings on fixture). Replace diaphragm assembly or reliefvalve for appropriate flush volume of fixture.

D. Inadequate water volume or pressure is available from supply.Increase flow rate or pressure to the valve. If gauges are not availableto measure supply pressure/volume, remove relief valve fromdiaphragm assembly and open the control stop.

If the fixture siphons: Additional water volume is required. Installhigher flushing volume relief valve or diaphragm assembly or cut flowring from guide.

If the fixture DOES NOT siphon (or a low consumption flush isrequired): Additional steps must be taken to increase the waterpressure and/or volume at the water supply. Contact fixturemanufacturer for minimum supply requirements of fixture.

5. Flushometer valve closes immediately (short flush).A. Worn or damaged diaphragm assembly. Replace diaphragm

assembly.

B. Handle assembly is damaged. Replace B-73-A handle or repair withB-51-A handle repair kit.

C. Low consumption diaphragm assembly is installed on watersaver/conventional fixture or urinal diaphragm assembly is installedon closet fixture. Determine the required flush volume (see label onvalve or markings on fixture). Replace relief valve or diaphragmassembly for appropriate flush volume of fixture.

6. Length of flush is too long (long flush) or fails to shut off.A. By-pass hole (upper filter ring) of diaphragm assembly is dirty.

Remove the diaphragm assembly. Disassemble the filter rings fromthe diaphragm, wash under running water, and reassemble. Replaceas necessary.

B. Relief valve or diaphragm assembly is damaged. Replace relief valveor diaphragm assembly.

C. Water saver/conventional diaphragm assembly is installed on lowconsumption fixture or closet diaphragm assembly is installed onurinal fixture. Determine the required flush volume (see label on valveor markings on fixture). Replace diaphragm assembly or relief valvefor appropriate flush volume of fixture.

D. Inside cover is damaged. Install new A-71 part.

E. Line water pressure dropped and is insufficient to close valve. Closethe control stop until pressure is restored.

F. Relief valve is not seated properly. Disassemble diaphragmcomponents (relief valve, filter rings, and diaphragm unit), wash underrunning water, and reassemble. Replace as necessary.

7. Chattering noise is heard during flush.A. Inside cover is damaged. Install new A-71 part.

B. Relief valve or diaphragm assembly is damaged. Replace relief valveor diaphragm assembly.

CARE AND CLEANING INSTRUCTIONSDO NOT USE abrasive or chemical cleaners to clean Flushometers that maydull the luster and attack the chrome or decorative finish. Use ONLY mildsoap and water, then wipe dry with a clean towel or cloth. When cleaningthe bathroom tile, protect the Flushometer from any splattering of cleaner.Acids and cleaning fluids can discolor or remove chrome plating.

TROUBLESHOOTING GUIDE

Warranty At Sloan, our warranty is more than a statement; it’s a lifetime commitment to our customers. Sloan Valve Limited Warranty Unless otherwise noted, Sloan Valve Company warrants its products, manufactured and sold for commercial or industrial uses, to be free from defects of material and workmanship for a period of three (3) years (one year for SF faucets, special finish and PWT electronics and 30 days on PWT software) from the date of first purchase. During this period, Sloan Valve Company will, at its option, repair, replace, or refund the purchase price of any produce which fails to confom with this warranty under normal use and service. This shall be the sole and exclusive remedy under this warranty. Products must be returned to Sloan Valve Company, at customer’s cost. No claims will be be allowed for labor, transportation or other costs. This warranty extends only to persons or organizations that purchase Sloan Valve Company’s products directly from Sloan Valve Company for purpose of resale. This warranty does not cover the life of batteries. There are no warranties which extend beyond the description on the face hereof. In no event is Sloan Valve Company responsible for any consequential damages of any measure whatsoever. Sloan Valve Return Policy Products which are determined to be defective or shipped incorrectly by Sloan Valve Company will be credited at invoice price. Products returned for reasons other than defects or Sloan shipping errors are subject to a 25% handling charge, return freight is at customers expense. All returns of Special Finish, Special Order, Scrub Sinks

and SloanStone product are subject to a minimum 50% handling charge and must be returned within one year. If the invoice is not available, then credit will be issued based on

the previous price sheet, if the price sheet is less than a year old. All returns must be authorized by the factory prior to returning. The factory will issue a return material authorization (RMA) number. The RMA number must be written on the shipping label, each load inspection and all related documentation. All returned material should be returned in the original, unopened shipping cartons, or suitably packed. The material is to be packaged such that it will not be damaged during the return. Material over two years old is subject to a 50% handling charge. Manual product/parts over five (5) years old and electronic product over three (3) years old will not be

excepted. PWT electronics will not be accepted after one year. Deductions will be made for any material returned that is not in saleable condition. Material not in saleable condition will be returned to customer or scrapped at

customer request. When material is to be returned, call your representative, who will contact the factory for an RMA number. The following information will be necessary: A. Invoice Number B. Product Part Number C. Product Code Number D. Product Date Code E. Quantity F. Reason for return requests (be specific, “defective” is not a reason). Material returned as defective but, on inspection, is found to be serviceable will be subject to credit reduction. A test report will be available on request. G. All returns are to be freight prepaid. The RMA number must be on each load and each container. Sloan FLUSHMATE™ Warranty For all Flushmate Warranty inquiries please go tohttps://www.flushmate.com/warranty/  

P-2

3

730427-100 Rev. B

1

2

4

CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE! !NOTE: Pictures may not exactly define contour of china and components.

INSTALLATION INSTRUCTIONS

Wall Hung Bathroom Sink

Introduction: Thank you for selecting our products...products which have been the benchmarks of fine quality for years. To help insure that the installation process will proceed smoothly, please read these instructions carefully before you begin. Also, review the recommended tools and materials list; carefully unpack and examine your new plumbing fixture.

Adjustable Wrench

Channel Lock PliersRegular Screwdriver

Recommended Tools & Materials

Phillips Screwdriver

Pipe Wrench

Putty Kinfe

DrillSaber Saw

Basin Wrench

Plumbers' Putty orCaulking

Tubing Cutter

TapeMeasure

Hacksaw

© American Standard Inc. 2003

Provide suitable reinforcement behind finished wall for lavatory hanger mounting screws. *Determine horizontal center line location of support from the table listed in Step 2. (Make sure support bottom extends to lavatory back wall bottom.)

NOTE: If replacing an existing sink be certain to shut off water supply before removing old sink.

*NOTE: For installation of models using concealed or exposed arms, follow instruction provided by arms manufacturer.

Level

HangerLocation

C/L of 2X8Support

FinishedFloor

*

Determine thedesired rim height(for example 32")then select from theTable at right theheight of the hangermounting boltscenterline

EXAMPLE:

For Lucerne:32"-1"=31"For Ledgewood:32"+2-7/8"=34-7/8"

Drill pilot holes in positioning screw slots of hanger. (Note: Some models are supplied with anchor screws, or steel hangers for lavatory installations. Other models are not provided with mounting hardware which can be purchased at local hardware outlets. Lavator-ies with bottom anchor screw holes should be secured with anchor screws in addition to hangers.

Part # ModelTABLE

Distance "A"

012403210355/03560372/037343004867/48695300

ComradeDeclynLucernePenlynLedgewoodRegalynLedgemere

- 2-1/2" (64mm)- 2-3/4" (70mm)- 1" (25mm)- 1/8" (3mm)+ 2-7/8" (73mm)+ 2-3/4" (70mm)+ 2-1/2" (64mm)

HOLES FORANCHORSCREWSIN BACKDRAPERY

RIMHEIGHT

* SUPPLIES ASREQUIRED

WASTE

FINISHED FLOOR

HANGER

C/L OF HANGERANCHORING SLOTS

MOUNTING SCREWHOLES (4)

POSITIONINGSCREW SLOTS (2)

A

Position hanger according to Step 2, making sure its center is aligned with the waste hole centerline. Mark the hanger screw locations through its mounting holes.

5

6

7

8

730427-100 Rev. B

AMERICAN STANDARD ONE-YEAR LIMITED WARRANTY

If inspection of this American Standard plumbing product, within one year after its initial installation, confirms that it is defective in materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.

This limited warranty does not apply to local building code compliance; since local building codes vary considerably, the purchaser of this product should check with a local building or plumbing contractor to insure local code compliance before installation.

This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American Standard.

American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)

This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not affect such statutory rights.

For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following address:

In the United States:American Standard, Inc.

One Centennial Ave.Piscataway, New Jersey 08855

Attention: Director of Consumer Affairs

Toll Free: (800) 442-1902

In Canada:American Standard, Inc.

2480 Stanfield Rd., Mississauga, Ontario

Canada L4Y 1S2Toll Free: (800) 387-0369

In Mexico:Customer Service Manager

American Standard, Inc.Via Morelos #330Col. Santa Clara

Ecatepec 55540 Edo. Mexico

Saniwares

SteelHanger

MountingScrew

PositioningScrew

Anchor Screw(if used)

Lavatory

Affix hanger to wall (hand tighten only). Mount lavatory for positioning, level the deck, and mark bottom anchor screw holes (if applicable). Remove lavatory, tighten the hanger positioning screws and drill pilot holes for anchor screws and 4 mounting screws. Install and tighten the mounting screws.

Return the fitted lavatory to the installed position. Connect trap to drain assembly hand tight to check alignment. It may be necessary to cut off part of the tailpiece (area "B") or part of the horizontal leg of the trap (area "C").

Secure lavatory on hanger as shown in 5. Insert and tighten anchor screws if applicable. Connect hot and cold supply lines to the shut-off valves. Tighten trap joints for watertight assembly. Apply a bead of caulk around the edge which contacts the wall as shown.

Following manufacturers instructions, install faucet and drain assembly. (Not included). Be certain to apply a bead of sealing putty on the underside of the drain (Part "A") in order to ensure a watertight seal between the lavatory and drain. Remove excess putty after installing drain on lavatory.

B

C

A

Shut-offValves

Caulk

jrodriguez

jar-signature

5/23/2014 Terms and Conditions : Chicago Faucets

http://www.chicagofaucets.com/terms.php 1/1

Limited Warranty

TO WHOM DOES THIS WARRANTY APPLY? - The Company extends the following limited warranty to the original user only.

WHAT DOES THIS WARRANTY COVER AND HOW LONG DOES IT LAST?

This warranty covers the following Commercial Products:

LIFETIME FAUCET WARRANTY - The "Faucet," defined as any metal cast, forged, stamped or formed portion of the Product,

not including electronic or moving parts or other products separately covered by this Limited Warranty or water restricting

components or other components, is warranted against material manufacturing defects for the life of the Product.

FIVE YEAR FAUCET WARRANTY - Certain Products and portions of the Product are warranted against material

manufacturing defects for a period of five (5) years from the date of Product purchase. Products warranted against material

manufacturing defects for a period of five (5) years from the date of Product purchase are referred to by the product numbers

42X, 43X, 15XX and E-Tronic™ - 4X, 5X, 6X, 7X, 8X and 9X. All zinc die cast portions of Product are warranted against

material manufacturing defects for a period of five (5) years from the date of Product purchase.

FIVE YEAR CARTRIDGE WARRANTY - The "Cartridge", defined as the metal portion of any Product typically referred to by the

product numbers containing 1-099, 1- 100, 1-310, 377X, 217X and 274X, excluding any rubber or plastic components, is

warranted against material manufacturing defects for a period of five (5) years from the date of Product purchase. All

Cartridges included in the Company's Single Control or Shower Products also are warranted against material

manufacturing defects for a period of five (5) years from the date of Product purchase.

ONE YEAR FINISH WARRANTY - COMMERCIAL - For Products used in commercial applications, the finish of the Product is

warranted against material manufacturing defects for a period of one (1) year from the date of Product purchase.

ELECTRONIC FAUCETS AND METERING MECHANICALS WARRANTY - Electronic and metering faucets mechanicals are

warranted against material manufacturing defects for a period of five (5) years from the date of Product purchase.

ELECTRONIC FAUCETS ELECTRONICS AND SOLENOID WARRANTY - Electronic faucets electronics and solenoid are

warranted against material manufacturing defects for a period of three (3) years from the date of Product purchase. This

warranty does not cover the life of the battery. The Company offers NOWARRANTY for Product batteries.

THIRTY DAY WARRANTY - PALM DEVICES - Palm devices are reconditioned and are warranted against material

manufacturing defects for a period of thirty days from the date of device purchase. The Company offers NOWARRANTY for

batteries, software (on a CD or from a website), damage the Palm device or software allegedly causes to any system, set-up

instructions, adaptors or other equipment used with the device.

P-3

5/23/2014 Terms and Conditions : Chicago Faucets

http://www.chicagofaucets.com/terms.php 1/1

Limited Warranty

TO WHOM DOES THIS WARRANTY APPLY? - The Company extends the following limited warranty to the original user only.

WHAT DOES THIS WARRANTY COVER AND HOW LONG DOES IT LAST?

This warranty covers the following Commercial Products:

LIFETIME FAUCET WARRANTY - The "Faucet," defined as any metal cast, forged, stamped or formed portion of the Product,

not including electronic or moving parts or other products separately covered by this Limited Warranty or water restricting

components or other components, is warranted against material manufacturing defects for the life of the Product.

FIVE YEAR FAUCET WARRANTY - Certain Products and portions of the Product are warranted against material

manufacturing defects for a period of five (5) years from the date of Product purchase. Products warranted against material

manufacturing defects for a period of five (5) years from the date of Product purchase are referred to by the product numbers

42X, 43X, 15XX and E-Tronic™ - 4X, 5X, 6X, 7X, 8X and 9X. All zinc die cast portions of Product are warranted against

material manufacturing defects for a period of five (5) years from the date of Product purchase.

FIVE YEAR CARTRIDGE WARRANTY - The "Cartridge", defined as the metal portion of any Product typically referred to by the

product numbers containing 1-099, 1- 100, 1-310, 377X, 217X and 274X, excluding any rubber or plastic components, is

warranted against material manufacturing defects for a period of five (5) years from the date of Product purchase. All

Cartridges included in the Company's Single Control or Shower Products also are warranted against material

manufacturing defects for a period of five (5) years from the date of Product purchase.

ONE YEAR FINISH WARRANTY - COMMERCIAL - For Products used in commercial applications, the finish of the Product is

warranted against material manufacturing defects for a period of one (1) year from the date of Product purchase.

ELECTRONIC FAUCETS AND METERING MECHANICALS WARRANTY - Electronic and metering faucets mechanicals are

warranted against material manufacturing defects for a period of five (5) years from the date of Product purchase.

ELECTRONIC FAUCETS ELECTRONICS AND SOLENOID WARRANTY - Electronic faucets electronics and solenoid are

warranted against material manufacturing defects for a period of three (3) years from the date of Product purchase. This

warranty does not cover the life of the battery. The Company offers NOWARRANTY for Product batteries.

THIRTY DAY WARRANTY - PALM DEVICES - Palm devices are reconditioned and are warranted against material

manufacturing defects for a period of thirty days from the date of device purchase. The Company offers NOWARRANTY for

batteries, software (on a CD or from a website), damage the Palm device or software allegedly causes to any system, set-up

instructions, adaptors or other equipment used with the device.