Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
A Tradition of Innovation
www.bromma.comWe reserve the right to change the design and technical data without prior notice.
© 2009 Cargotec Sweden AB – All rights reserved. PI-SSX45E - en, Rev 01, Apr 2009
Product InformatIon
SSX45E All electric Ship to Shore Spreader
The Bromma SSX45E all electric ship to shore spreader
has been designed and built for long, reliable service on
latest generation ship to shore cranes in high throughput
environments.
The telescopic spreader is of a rectangular frame construc-
tion enabling easy location on containers. The spreader is
as standard equipped with 4 x 10 tonnes lifting lugs in the
corners of the end beams for heavy lifts and for handling
damaged containers. The spreader can adjust its length to
lift 20 foot, 30 foot (option), 40 and 45 foot containers
using ISO floating twistlocks.
The spreader can retract to the 19 foot–6 inch position
in case it becomes jammed in the ship’s 20 foot cell.
The design with recessed end beams makes handling of
lashing frames and hatch covers possible. All motions of
the spreader are controlled from the driver’s cab and there
are provisions made for signals in the cab indicating the
position of the twistlocks and landing pin status.
All movements of the SSX45E are electrically driven. This
means that the speader is silent and consumes energy only
when moving.
Made of high quality steel, the standard SSX45E spreader
provides high lifting capacity with a low nominal tare
weight thanks to the box design of the telescoping beams
and the main frame. The spreader is designed in accordance
with DIN 15018 H2B4. All components can be easily assemb-
led, adjusted, removed and are accessible for inspection and
maintenance.
The spreader comes with the SCS3 Spreader Control System,
reducing and preventing downtime through improvements
in the area of electrical connections. It will also shorten
downtime through faster spreader fault diagnostics.
major features Adjustable for 20’, 30’ (option) 40’ and 45’ contai-
ners Recessed end beams allow handling of lashing
frames and hatch covers Environmental friendly due to its all electric design
Advanced communications system reduces downtime considerably
Fast trouble shooting Fulfils design criteria among DIN 15018 H2B4, FEM
1.001 and British Standard BS 2573
Container sizes with SSX45E20’ 30’ 40’ 45’
The spreader shown is customized with extra equipment
2www.bromma.comWe reserve the right to change the design and technical data without prior notice.
© 2009 Cargotec Sweden AB – All rights reserved. PI-SSX45E - en, Rev 01, Apr 2009
Tension rod
Absolute encoder
Electric motor/gearbox
Shock absorber
Endless chain
Tension rod
Shock absorber
telescoPIng system
Glide plates
The two telescopic beam units run on glide plates, one at each bottom corner of the main frame and one at each top end of the telescopic beams. Glide plates are also mounted at each lower end of the telescopic beams. This ensures low friction and a smooth movement when telescoping.
telescoPIc drIve system
The telescopic system is driven by means of an electric motor with gearbox connected to an endless chain. The motor is equipped with a built in brake which holds the spreader in position during operation. The chain is fitted with a Bromma design shock absorber at both ends. The shock absorber is designed to dampen the effects of impact on the spreader structure and components due to loads imposed to the spreader ends.
The telescoping system’s ability of absorbing extreme loads mechanically provides the end user with a highly reliable spreader with increased life even under extreme load condi-tions.
The flexibility in the system allows small changes in spreader length when handling distorted containers.
This system stops accurately in all positions. It is durable and strong but has low weight, is easy to maintain and has long service intervals. The telescoping positions are con-trolled by an absolute encoder placed on one of the gear-boxes.
3www.bromma.comWe reserve the right to change the design and technical data without prior notice.
© 2009 Cargotec Sweden AB – All rights reserved. PI-SSX45E - en, Rev 01, Apr 2009
twIstlock system
flIPPers
The spreader is equipped with flipper units located in each corner of the spreader to guide the spreader onto the con-tainer.
The flipper unit consists of an electric motor attached to a gearbox. The gearbox is bolted to the end beam. The flipper arm is attached to the outcoming gearbox shafts. The flipper arms make a movement of 180 degrees from their upper position down to their working location. The gearbox is equipped with a safety function which makes the flipper retract at a force of 3,000 Nm or more.
Flipper arm
Electric motor
Gearbox
Four twistlocks are located in the corners of the spreader to engage and lift the container.
Proximity switch for locked position
Proximity switch for unlocked position
Helical-worm geared motor
Draw bars
Twistlock
Landing pin
Blocking stop
Twistlock armProximity switch for landing pin
Blocking key
The twistlocks are manoeuvred by a helical-worm geared motor, which is connected to the twistlock arms by two draw bars. Two switches indicate the locked and unlocked positions. The switches also ensure that the motor is stopped in correct location at each end position.
A spring loaded landing pin near each twistlock is pushed up into the twistlock housing and activates a proximity switch when the spreader is landed on the container. The twistlocks can only be turned when all the corners of the spreader are landed. At the same time, the blocking key is moved high enough so the blocking stop on the twistlock lever arm passes underneath it. During hoisting the land-ing pin is in the ”down” position and prevents the twistlock from turning. The floating range is ±6 mm in all directions. The twistlock pins are proof load tested to 37 tonnes.
4www.bromma.comWe reserve the right to change the design and technical data without prior notice.
© 2009 Cargotec Sweden AB – All rights reserved. PI-SSX45E - en, Rev 01, Apr 2009
electrIcal system
The power required to operate the spreader’s electrical components is obtained from the crane. All electrical com-ponents on the spreader are designed to withstand loads imposed during container handling operations and suitable for a marine environment.
The electrical components are mounted in a stainless steel cabinet, IP 67. All cables are well protected in cable chains.
The spreader is supplied with CANopen slave units. This enhances the possibility of monitoring each I/O point and reduces the number of cables needed and the replacement time for connecting sensors and actuators to the controls.
CANopen box
The spreader has a control voltage of 24 V DC.
The electrical safety features to protect and ensure proper handling of containers are as follows: Spreader cannot be hoisted unless all four twistlocks
are fully ”Locked” or ”Unlocked”. (Provided the crane controls have a hoist permit safety circuit.)
Spreader twistlocks can only be ”Locked” or ”Unlocked” when all four corners are properly seated on a container or hatch cover.
monItorIng and dIagnostIc system scs3
For monitoring and diagnosing the SSX45E is equipped with the SCS3 Spreader Control System. The SCS3 can con-nect to a wide variety of host controllers including PLCs and PC-based control systems.
The rugged SCS3 control unit is a computer that is equipped with a touch screen and mounted on the spreader for easy access. Monitoring and diagnostics can be available in dif-ferent ways; on the screen, on the crane, via an external PC or a handheld computer.
The SCS3 system delivers advanced monitoring and diag-nostic information, which means that service staff can react faster to fault events. Instead of investigating possible sources of fault events one by one, the SCS3 gives service technicians specific, precise information, enabling them to quickly solve the problems occurred.
The SCS3 system simplifies handling of the spreader and prevents fault events. It also eliminates or minimizes junc-tion boxes, terminal strips, and relays – areas where wire breakage is common. Conventional wiring is reduced.
The SCS3 system comes as standard with all Bromma All electric ship to shore systems.
5www.bromma.comWe reserve the right to change the design and technical data without prior notice.
© 2009 Cargotec Sweden AB – All rights reserved. PI-SSX45E - en, Rev 01, Apr 2009
dImensIonal drawIngs – ssX45e
The spreader shown is customized
We reserve the right to change the design and technical data without prior notice.© 2009 Cargotec Sweden AB – All rights reserved.
PI-SSX45E - en, Rev 01, Apr 2009
For nearest contact and latest information on Bromma products and services, visit the Bromma website at www.bromma.com
Bromma is part of Cargotec Corporation
technIcal data ssX45e
Lifting capacity: (According to DIN 15018 H2B4)
41 tonnes evenly loaded
41 tonnes ±10% eccentric loading
Lifting lugs 4 x 10 tonnes in the main frame and end beams
Weight: 9.5 tonnes (without extra equipment)
Dimensions: See dimensional drawing (previous page)
Telescopic motion: From 20’ to 45’ in approximately 30 seconds
Flipper arm speed: 180° in 3–5 seconds
Twistlock rotation: 90° in approximately 1 second
Power supply: 400/230 V AC 50 Hz or otherwise as agreed
Max power consumption: 0–7.5 kW
Control system: SCS3 Spreader Control System
Control voltage: 24 V DC
Electrical cabinet: Stainless steel IP 67
Surface conditioning: Sand-blasted SA 2.5
50 microns 2-component zinc epoxy
70 microns 2-component MIO epoxy
40 microns 2-component acrylic epoxy
40 microns 2-component acrylic epoxy
Design criteria: DIN 15018 H2B4; FEM 1.001; British Standard BS 2573
Manuals: Full service and repair manual supplied
Warranty: 1 year