SS7 Glossary - Squire Technologies · SS7 Glossary Squire Technologies – Confidential Document S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts \Appendix-C-SS7-SVI-Resource-Glossary

$Page 1: SS7 Glossary - Squire Technologies · SS7 Glossary Squire Technologies – Confidential Document S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts \Appendix-C-SS7-SVI-Resource-Glossary$
SS7 Glossary

Document SQ00481

Version 2.6

©Squire Technologies

This document is the property of Squire Technologies. Information contained herein is confidential. This document, either in whole or in

part, must not be reproduced or disclosed to others or used for purposes other than that for which it has been supplied, without Squire

Technologies prior written permission, or, if any part hereof is furnished by virtue of a contract with a third party, as expressly

authorised under that contract.

SS7 Glossary Squire Technologies – Confidential Document

S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts\Appendix-C-SS7-SVI-Resource-Glossary V2.6 -SQ00481.docx Page 2 of 124

Change History

Version Change Made Author Authorised Date

2.0 Added Table of Contents and changed Version Number

DR AC 10.02.2014

2.1 Added CAP SSN Attribute of SS7 Stack.

BT BT 12.08.2014

2.2 Added CAMEL Phases Attribute of SS7 Stack.

BT BT 10.10.2014

2.3 Added Stats for the ASP, AS, SCTP, L3Label, TcapLabel and SccpLabel

JF JF 15.07.2015

2.4 Added INAP Application Context Attribute to SS7 Stack

BT BT 21.09.2016

2.5 Added XML Resource JF JF 01.06.2017

2.6 Updated entries below to be current:

2.5.3.41 M2PA Timer

2.6.3.20 Options 2.6.3.21 send CVT 2.6.3.22 Send CQM 2.10.3.26 M3UA AS

2.10.3.27 SSME XML

2.10.3.28 Tx Bits Throttle 2.10.3.29 Tx MSU Throttle 2.10.3.30 Tx Congestion

2.10.3.31 Tx Failure 2.10.3.32 Routing Failures

2.10.3.33 Rx UDTS

2.11.3.42 Ignore API Client

2.13.3.36 Options 2.14.3.28 displayRegistrations

2.10.3.8 Transfer Report

BT SS 11.11.2019



Contents 1.0 Introduction ................................................................................................. 6

1.1 Resource Name ............................................................................................. 6

1.2 Resource Identifier ......................................................................................... 6

1.3 Attribute ..................................................................................................... 6

1.4 Value .......................................................................................................... 6

2.0 Resources .................................................................................................... 7

2.1 Common Attributes ........................................................................................ 7

2.1.1 Status .................................................................................................... 7

2.1.2 Flags ..................................................................................................... 7

2.1.3 Inservice ................................................................................................ 8

2.1.4 Outservice .............................................................................................. 8

2.1.5 Description ............................................................................................. 8

2.1.6 Options .................................................................................................. 9

2.2 Card ........................................................................................................... 9

2.2.1 Description ............................................................................................. 9

2.2.2 Products ................................................................................................ 9

2.2.3 Attributes ............................................................................................... 9

2.3 Driver ........................................................................................................ 15

2.3.1 Description ............................................................................................ 15

2.3.2 Products ............................................................................................... 15

2.3.3 Attributes .............................................................................................. 15

2.4 Interface .................................................................................................... 15

2.4.1 Description ............................................................................................ 15

2.4.2 Products ............................................................................................... 15

2.4.3 Attributes .............................................................................................. 15

2.5 Signalling Link .............................................................................................. 19

2.5.1 Description ............................................................................................ 19

2.5.2 Products ............................................................................................... 19

2.5.3 Attributes .............................................................................................. 19

2.6 Circuit ....................................................................................................... 27

2.6.1 Description ............................................................................................ 27

2.6.2 Products ............................................................................................... 27

2.6.3 Attributes .............................................................................................. 27

2.7 Circuit Group ............................................................................................... 33

2.7.1 Description ............................................................................................ 33

2.7.2 Products ............................................................................................... 33



2.7.3 Attributes .............................................................................................. 33

2.8 Originating Point........................................................................................... 35

2.8.1 Description ............................................................................................ 35

2.8.2 Products ............................................................................................... 35

2.8.3 Attributes .............................................................................................. 35

2.9 Destination Point .......................................................................................... 38

2.9.1 Description ............................................................................................ 38

2.9.2 Products ............................................................................................... 38

2.9.3 Attributes .............................................................................................. 38

2.10 Linkset ................................................................................................... 41

2.10.1 Description ......................................................................................... 41

2.10.2 Products ............................................................................................ 41

2.10.3 Attributes ........................................................................................... 42

2.11 SS7 Stack ................................................................................................. 48

2.11.1 Description ......................................................................................... 48

2.11.2 Products ............................................................................................ 48

2.11.3 Attributes ........................................................................................... 48

2.12 MTP Route ............................................................................................... 57

2.12.1 Description ......................................................................................... 57

2.12.2 Products ............................................................................................ 57

2.12.3 Attributes ........................................................................................... 57

2.13 SCTP ...................................................................................................... 61

2.13.1 Description ......................................................................................... 61

2.13.2 Products ............................................................................................ 61

2.13.3 Attributes ........................................................................................... 61

2.14 ASP ........................................................................................................ 70

2.14.1 Description ......................................................................................... 70

2.14.2 Products ............................................................................................ 70

2.14.3 Attributes ........................................................................................... 70

2.15 AS ......................................................................................................... 76

2.15.1 Description ......................................................................................... 76

2.15.2 Products ............................................................................................ 76

2.15.3 Attributes ........................................................................................... 76

2.16 L3 Label / SCCP Label / TCAP Label ................................................................ 82

2.16.1 L3 Label ............................................................................................. 82

2.16.2 SCCP Label ......................................................................................... 90

2.16.3 TCAP Label ....................................................................................... 116

2.17 MTP CDR ............................................................................................... 119



2.17.1 Description ....................................................................................... 119

2.17.2 Products .......................................................................................... 119

2.17.3 Attributes ......................................................................................... 120

2.18 XML ..................................................................................................... 121

2.18.1 Description ....................................................................................... 121

2.18.2 Products .......................................................................................... 121

2.18.3 Attributes ......................................................................................... 121



1.0 Introduction The SVI controls all aspects of the system by abstracting the system down to a number of database

resources. These resources are further divided into sub resource types that describe the operation

of a given resource. There are a number of instances of a given resource and each resource has a

number of configurable attributes.

These resources are used to allow the administrator to configure and maintain the system.

All of these resources are arranged into a parent-child hierarchical arrangement. When started up

the SVI will bring the resources into service starting with the system resource and continuing down

through the children resources. A resource will only be brought into service once its parent

resource is configured and in-service.

Each resource has the following components

1.1 Resource Name

Each resource has a unique name which provides a unique operation for the SVI product.

1.2 Resource Identifier An individual resource instance is identified by a unique name.

1.3 Attribute The attribute field is the attribute of the resource that is to be configured. These are described for

each resource within this document.

1.4 Value

This field contains the value of the attribute. The following type of values are valid:

Type Description

Integer This is a number in either decimal or hexadecimal format. If the number is in hexadecimal format the 'H' character is prefixed to the number to indicate it is a hexadecimal number (Ha3)

Drop Down List This type of value provides a definitive list of options from which the user can select one of the options

Resource Identifier This is a drop down list which will provide all configured resources of the same type allowing the user to select a single instance of a resource

Bit Mask Flag This type of value provides the user with a list of options from which the user can choose multiple choices.

Integer range The integer range field is a list including ranges of integers for example 1,2,3-10,12-17,20

User String This is a NULL terminated ASCII character string

IP Address This describes an IP address ie (192.168.2.182)

Boolean A Boolean flag is either True or False

Resource Identifier Range

This allows for multiple resources to be identified

Digit Match A digit match is a string of E164 numbers with the special characters '



2.0 Resources

2.1 Common Attributes

The following section contains attributes that are common to all resources

2.1.1 Status This defines the status of the attribute, which will either be in service (INS) or out of service (OOS).

Description

This defines the status of the resource instance. When configuring managed resources this should

be set to Start, all other resource types should be INS.

2.1.1.1 Definition

Applicable Modes User Type

All Read Write Licensed

Drop Down List

2.1.1.2 Values

Value Description

Niu Instance of resource not configured on system

Osf Resource is waiting for parent to be in service before it attempts to come into service

Oos The Resource has been manually removed from service

Osc The Resource is waiting for the parent to come into service before it attempts to configure this resource

Osd The resource's parent is out of service and will come straight back into service once the resource's parent is in service.

Osfd The

Oscp The resource is currently attempting to be configured

Osp The resource is currently attempting to come into service

INS The resource is INSERVICE

Start This pre-configures the resource to its correct startup state

ERR An Error has occurred on this resource.

2.1.2 Flags

2.1.2.1 Description

The following flags define internally the behaviour of the resource. These are not user defined and

are provided only for information purposes.

2.1.2.2 Definition


All Read None



2.1.2.3 Values

Value Description

Secure This resource will be secured on a fail over

Applied This indicates that a resource has been reconfigured and the system needs to reapply the configuration to the resource owner

Add Indicates that the resource is scheduled to be added to the system hierarchy

Remove Indicates that the resource is scheduled to be removed from the system hierarchy

Start Indicates that the resource is scheduled to be started

Reconfigured Indicates that the resource has been reconfigured and requires to be Removed then added and then started

Read This attribute has read permissions

Write This attribute has write permissions

No-Default This resource will not be displayed in the CLI if the default value is configured

No-Secure Do not secure this resource at failover

No-Init Do not initialise this

No-GUI Do not display this attribute in the GUI

Licensed The number of instances of this resource is licensed

2.1.3 Inservice

2.1.3.1 Description

The Inservice attribute displays the time that this resource came into service.

2.1.3.2 Definition


All resources Read Time

2.1.4 Outservice

2.1.4.1 Description

The Outservice attribute displays the time that this resource last went from an in service state to

an out of service state.

2.1.4.2 Definition


All resources Read Time

2.1.5 Description

2.1.5.1 Description

Description is a free text field to allow for a human readable name of the resource. Please note

that this field is automatically populated by the SVI-MS from the “Name” input field.

2.1.5.2 Definition


Read Write



No-Default

2.1.6 Options

2.1.6.1 Description

These are a set of options which relate to the resource in question that you can enable or disable at

any time.

2.1.6.2 Definition


Read Write No-Default

2.1.6.3 Values

Value Description

SNMP-Trap If the resource changes state, an SNMP trap will be sent to the address configured on the debug resource.

2.2 Card

2.2.1 Description

The card resource defines the operation and configuration of specialised telephony hardware

contained in the product.

2.2.2 Products

SVI-MG | SVI-9225 | SVI-STP | SVI-SG

2.2.3 Attributes

2.2.3.1 Map

2.2.3.1.1 Description When using different type of telephony hardware this attribute allows the same hardware to be

grouped together with each group starting from 0. When using the same type of hardware this will

have the same instance as the resource instance.

2.2.3.1.2 Definition


All cards Read Write

Integer

2.2.3.2 Type

2.2.3.2.1 Description This specifies the particular type of telephony hardware that is being used



All card types Read Drop Down List



Write

2.2.3.2.3 Values

Value Description

NS700 TDM Signalling only PCI card (Applicable to all MPACXXXX cards)

TP260 E1/T1 TDM to VoIP media and signalling card in PCI form factor

TP1610 E1/T1 TDM to VoIP media and signalling card in CPCI form factor

TP6310 STM-1 TDM to VoIP media and signalling card in CPCI form factor

Sangoma IP Only D500 Transcoding Card

2.2.3.3 Driver

2.2.3.3.1 Description Contains the identity of the software driver resource that the particular card is registered to.



All card types Read Write

Resource Identifier

2.2.3.4 Download

2.2.3.4.1 Description Contains the name of the cards download image.




String

2.2.3.5 Role

2.2.3.5.1 Description Describes the timing role within a H100/H110 synchronised telephony bus environment.




Drop Down List

2.2.3.5.3 Values

Value Description

A Primary Master Provides the source port timing to the H100 A Primary Master bus

B Primary Master Provides the source port timing to the H100 B Primary Master bus

A Secondary Master Provides the source port timing to the H100 A Secondary Master bus

B Secondary Master Provides the source port timing to the H100 B Secondary Master bus

A Slave Takes its timing from the A bus

B Slave Takes its timing from the B bus

2.2.3.6 Source

2.2.3.6.1 Description



If the card is providing timing to the H100 A/B primary or secondary bus this defines the onboard

source of the timing.




Drop Down List

2.2.3.6.3 Values

Value Description

Port 0 The bus timing is originated from Port 0 on the card








Internal The bus timing is originated from the internal clock on the card

None This card does not provide timing to the bus

2.2.3.7 BusType

2.2.3.7.1 Description This defines the type of telephony bus used on the TP260 if it is shipped with the MVIP option.



Card type TP260 only Read Write

Drop Down List

2.2.3.7.3 Values

Value Description

H100 The H100 bus is being used on this card

MVIP The MVIP bus is being used on this card

H110 The H110 bus is being used on this card

2.2.3.8 Address / Address Port 0

2.2.3.8.1 Description For telephony cards that are connected over IP, this defines the IP address of the card.



All cards connected over IP Read Write No-Default

IP address

2.2.3.9 Address Port 1

2.2.3.9.1 Description For telephony cards that are connected over IP and have a secondary NIC connection. this defines

the IP address of that connection.





All cards connected over IP Read Write No-Default

IP address

2.2.3.10 Subnet

2.2.3.10.1 Description For the TPxxx range of cards that defines the subnet mask of the IP connection.



For TP cards only Read Write No-Default

IP subnet mask address i.e. 255.255.255.248

2.2.3.11 Gateway

2.2.3.11.1 Description For TP cards this defines the default gateway address to be used.



TP cards only Read Write No-Default

IP address

2.2.3.12 Selfboot

2.2.3.12.1 Description This is set to True if the Card being used is a NS700 card used in self boot mode



NS700 card used in self boot mode

Read Write No-Default

Boolean

2.2.3.13 G168EC

2.2.3.13.1 Description This sets the Echo Cancellation tail length for a call with Echo cancellation



TP cards Read Write No-Default

Drop List

2.2.3.13.3 Values

Value Description

Off Disable Echo Cancellation



32ms 32 milliseconds echo cancellation tail length



2.2.3.14 H1000 Termination

2.2.3.14.1 Description This defines if the telephony card is terminating the end of the telephony bus.




Boolean

2.2.3.15 Syslog-Enable

2.2.3.15.1 Description This turns on extra debugging on the card if set to True. The debug is delivered over IP to a debug

server.



All Read Write No-Default

Drop down List

2.2.3.15.3 Values

Value Description

Disable Disable logging

Enable Enable logging

2.2.3.16 Syslog-IP

2.2.3.16.1 Description This sets the IP address of the debug server which is collecting the debug information.




IP Address

2.2.3.17 Syslog-Port

2.2.3.17.1 Description This sets the IP address port of the debug server which is collecting the debug information.




Port Address



2.2.3.18 Enable Debug

2.2.3.18.1 Description For NS700 cards this command is used to activate the debug.



NS700 Read Write No-Default

Command

2.2.3.18.3 Values

Value Description

Disable Disable logging

Enable Enable logging

2.2.3.19 Tp-Sig-Channels / Add Tp-Sig-Channel

2.2.3.19.1 Description When using the TP cards for signalling DSP channels need to be reserved for handling the signalling

on a given timeslot on an E1/T1. The DSP channels are linear from 0-30 for the first E1, 31-61 for

second E1, etc. Therefore to set up two signalling links on timeslot 1 on the first two interfaces the

DSP channels 0 and 31 would be used.




Integer Array

2.2.3.20 Internal-TFTP-Server

2.2.3.20.1 Description Used to provide the TP260 card with the IP of the TFTP server to download its firmware/config

from.




IP Address

2.2.3.21 Options

2.2.3.21.1 Description This allows for additional configuration options.




Drop Down List

2.2.3.21.3 Values

Value Description



SNMP-Trap This provides an SNMP trap when the card status changes state

2.3 Driver

2.3.1 Description The driver resource describes the behaviour of the interface between a card resource and the SVI

system. Multiple cards of the same type can be associated with a single driver.

2.3.2 Products

SVI-MG | SVI-9225 | SVI-STP | SVI-SG

2.3.3 Attributes

2.3.3.1 Type


The behaviour type of the resource instance.



All Read Write

Drop down List

2.3.3.1.3 Values

Value Description

NS700 Driver For all MPACXXXX cards

TP260 Driver TPNCP Behaviour type when controlling the TP cards over IP using the native TPNCP API TP1610 Driver TPNCP

TP6310 TPNCP

Sangoma Driver For D500

2.4 Interface

2.4.1 Description

For a TDM enabled system the interface resource is a TDM interface that is either located directly

on the SVI or on a third party media gateway.

For the SBC the interface is the connection between the signalling SVI and the RTP routers which

provide handling of the media strings.

2.4.2 Products SVI-MG | SVI-9225 | SVI-STP | SVI-SG | SVI-SBC | SVI-MGC

2.4.3 Attributes

2.4.3.1 Type


The behaviour type of the resource instance.



All Read Write

Drop Down List



2.4.3.1.3 Values

Value Description

ISDN Cable This interface is an ISDN cable either located on the SVI or on a third party media gateway

SS7 Cable This interface is an SS7 Cable either located on the SVI or on a third party media gateway

STM1 SS7 Cable This interface is an STM-1 SS7 interconnect cable located on the SVI

STM1 ISDN Cable This interface is an STM-1 ISDN interconnect cable located on the SVI

TP260 Cable

Megaco Cable This interface is on a third party Media Gateway controlled via MEGACO/H.248

MG Ethernet This interface defines the connection between the SVI and individual RTP routers

2.4.3.2 Card


For interfaces connected locally on the SVI this defines the card instance that the interface is

connected to.



As defined Read Write No-Default

Resource Identifier

2.4.3.3 Media Gateway, Media GW


For connections to a media gateway device this defines the Media Gateway resource instance that

the interface is located on.



As defined Read Write

Resource Identifier

2.4.3.4 TrunkMap


Defines the mapping of the interface onto the card it is assigned to. Note required to be set by

user.



As defined Read Write No-GUI

2.4.3.5 BoardMap


Defines the mapping of the interface onto the card it is assigned to. Note required to be set by

user.





As defined Read Write No-GUI

2.4.3.6 Crc


For NS700 card type interfaces terminating on the SVI this attribute defines if CRC is active on the

interface.



NS700 type cards Read Write

Drop Down List

2.4.3.6.3 Values

Value Description

CRC ON CRC is active on this interface

CRC OFF CRC is not active on this interface

2.4.3.7 Electrical


This defines the electrical characteristics of NS700 type interfaces terminating on the SVI.



NS700 type cards Read Write

Drop Down List

2.4.3.7.3 Values

Value

E1 75 HDB3

E1 120 HDB3

T1 100 SF_B8ZS

T1 100 SF_AMI

T1 100 ESF_B8ZS

T1 100 ESF AMI

E1 75 AMI

E1 120 AMI

2.4.3.8 Name


This defines the MGCP interface name for connection of the SVI to a media gateway via MGCP.



All Read Write

User String



2.4.3.9 Value Name


End of Life

2.4.3.10 Default Circuits


End of Life

2.4.3.11 Suffix Name


End of Life

2.4.3.12 Tdmc Gain


For H.248 remote media gateway's this allows for the gain to be set on the interface.



H.248 remote gateways Read Write

Integer

2.4.3.13 Tdmc EC


For H.248 remote media gateway's this allows for the echo cancellation to be set on the interface.



H.248 remote gateways Read Write

Boolean

2.4.3.14 Audit Timeslot


This defines how the SVI will audit an MGCP gateway interface. If this is not set then the Audit of

the interface will use the '*' wild card, if it is set to a timeslot value the Audit will use this timeslot

value to audit the entire interface.



MGCP Media Gateways Read Write

Integer

2.4.3.15 Trunk Group


End of Life.



2.5 Signalling Link

2.5.1 Description

Defines an SS7 signalling link of an SS7 interconnect.

2.5.2 Products

SVI-MG | SVI-SG | SVI-MGC | SVI-STP | SVI-9225 | SVI-9220 | SVI-SMSC

2.5.3 Attributes

2.5.3.1 Type

2.5.3.1.1 Description The behaviour type of the resource instance.



All Read Write

Drop Down List

2.5.3.1.3 Values

Value Description

SS7 Signalling Link SS7 Signalling Link

2.5.3.2 Map

2.5.3.2.1 Description Unique global identifier for the link in the MTPL3 Stack.



All Read Write

Integer

2.5.3.3 Card

2.5.3.3.1 Description End of Life

2.5.3.4 Interface

2.5.3.4.1 Description Specifies the instance of the interface resource that the signalling link will be located on.



All but M2PA links Read Write

Resource Identifier

2.5.3.5 Channelled

2.5.3.5.1 Description Specifies the Interface/Channel ID in the M2UA/SLT AS. Must be unique per AS.





M2UA and SLT Links Read Write

Integer

2.5.3.6 Trunk


2.5.3.7 Timeslot

2.5.3.7.1 Description Specifies the signalling timeslot.



All but M2PA links Read Write

Integer

2.5.3.8 SLC

2.5.3.8.1 Description Specifies the signalling link code of the signalling link.



All Links Applied Read Write

Integer

2.5.3.9 Originating

2.5.3.9.1 Description Specifies the instance of the originating point resource to which the signalling link is associated to.



All Links Read Write

Resource Identifier

2.5.3.10 Linkset

2.5.3.10.1 Description Indicates the instance of the linkset resource for which this linkset is associated to.




Resource Identifier



2.5.3.11 Interface ID

2.5.3.11.1 Description As Channel ID – must be set as the same value.




Integer

2.5.3.12 AS

2.5.3.12.1 Description If M2UA/SLT is used this specifies the AS which the signalling link is associated with.




Resource Identifier

2.5.3.13 Stream


2.5.3.14 SLT Type

2.5.3.14.1 Description Allows setting of the Service Indicator to be Special or Regular Maintenance type (for ANSI MTPL3

only).



All Links Applied Read Write

Drop Down List

2.5.3.14.3 Values

Value Description

Regular Sets SI value to 1

Special Sets SI value to 2

2.5.3.15 L2 Task

2.5.3.15.1 Description Defines the MTP Layer 2 task that controls the link. Leave blank for default.



SLT Links Read Write

User String



2.5.3.15.3 Values

Value Description

SESSMGR Sets MTP Layer 2 task to be Session Manager

2.5.3.16 Force Normal

2.5.3.16.1 Description Allows the user to define the type of proving used for this signalling link.



All Links Read Write No-Default

Drop Down List

2.5.3.16.3 Values

Value Description

Standard Will send Emergency Proving for first link aligned in a Linkset and Normal for subsequent

False As Standard

Always Emergency Will send Emergency Proving for all links in a linkset

Always Normal Will send Normal Proving for all links in a linkset

True As Always Normal

2.5.3.17 Set LPO

2.5.3.17.1 Description Used to force a Local Processor Outage MTP L3 Event on the link via the OA&M.

2.5.3.18 Set LPR

2.5.3.18.1 Description Used to force a Local Processor Recovered MTP L3 Event on the link via the OA&M.

2.5.3.19 Inhibit

2.5.3.19.1 Description Used to force an Inhibit MTP L3 Event on the link via the OA&M.

2.5.3.20 Uninhibit

2.5.3.20.1 Description Used to force an Inhibit MTP L3 Event on the link via the OA&M.

2.5.3.21 Debug

2.5.3.21.1 Description Enable enhanced debug for MTPL3 or M2PA.






Bit Mask Flag

2.5.3.21.3 Values

Value Description

None No debug enabled

M2PA M2PA debug enabled

MTPL3 MTP Layer 3 debug enabled

2.5.3.22 Protocol

2.5.3.22.1 Description End of Life (now set on ASP).

2.5.3.23 SLTM

2.5.3.23.1 Description Enable or disable the sending of Signalling Link Test Messages.




Boolean

2.5.3.23.3 Values

Value Description

True Send SLTM (default)

False Do not send SLTM

2.5.3.24 Variant

2.5.3.24.1 Description Set the protocol variant of the link.




Drop Down List

2.5.3.24.3 Values

Value Description

ITU Sets the standard used to ITU

ANSI Sets the standard used to ANSI

Chinese Sets the standard used to Chinese

TTC Sets the standard used to TTC



2.5.3.25 LI Priority Bit

2.5.3.25.1 Description For Japanese only. Allows setting of the Priority Bit on SNM, SNTM and SNTM2 messages.




Boolean

2.5.3.25.3 Values

Value Description

False Normal Priority (default)

True Set priority to 3

2.5.3.26 Transmission Rate

2.5.3.26.1 Description (T1 Links only) Specifies the Signalling Link Transmission rate.



All TDM Links Read Write

Drop Down List

2.5.3.26.3 Values

Value Description

64K Default value used for most E1 interconnects

56K Used for some T1 interconnects

2MB Used for HSL over E1 interconnects

2.5.3.27 Max Throughput


2.5.3.28 Queue Size


2.5.3.29 Tx MSU Total

2.5.3.29.1 Description Statistic showing total number of MSU’s sent since system start.



All Links Read Integer



2.5.3.30 Tx MSU Sec

2.5.3.30.1 Description Statistic showing real-time MSU/Second being sent.




2.5.3.31 Tx MSU Sec Max

2.5.3.31.1 Description Statistic showing maximum MSU/Second send rate since system start.




2.5.3.32 Rx MSU Total

2.5.3.32.1 Description Statistic showing total number of MSU’s received since system start.




2.5.3.33 Rx MSU Sec

2.5.3.33.1 Description Statistic showing real-time MSU/Second being received.




2.5.3.34 Rx MSU Sec Max

2.5.3.34.1 Description Statistic showing maximum MSU/Second receive rate since system start.




2.5.3.35 Tx Bits Total

2.5.3.35.1 Description Statistic showing total number of Bit’s sent since system start.






2.5.3.36 Tx Bits Sec

2.5.3.36.1 Description Statistic showing real-time Bit/Second being sent




2.5.3.37 Tx Bits Sec Max

2.5.3.37.1 Description Statistic showing maximum Bit/Second send rate since system start




2.5.3.38 Rx Bits Total

2.5.3.38.1 Description Statistic showing total number of Bit’s received since system start




2.5.3.39 Rx Bits Sec

2.5.3.39.1 Description Statistic showing real-time Bit/Second being received




2.5.3.40 Rx Bits Sec Max

2.5.3.40.1 Description Statistic showing maximum Bit/Second receive rate since system start




2.5.3.41 M2PA Timer




Specifies the instance of the m2pa timer resource to which the signalling link will use to override the default timer values.




Resource Identifier

2.6 Circuit

2.6.1 Description

Specifies the SS7 circuits for the SS7 interconnect.

2.6.2 Products SVI-MG | SVI-MGC | SVI-9225 | SVI-9220

2.6.3 Attributes

2.6.3.1 Type


The behaviour type for the resource instance.



All Circuits Read Write

Drop Down List

2.6.3.1.3 Values

Value Description

ISUP Circuit For ITU Based ISUP Circuits

ISUP Circuit DI For ITU Based ISUP Circuits with Drop/Insert Routing

IUP Circuit For IUP Circuits

IUP Circuit DI For IUP Circuits with Drop/Insert Routing

ANSI Circuit For ANSI ISUP Circuits

ANSI Circuit DI For ANSI ISUP Circuits with Drop/Insert Routing

ISDN Circuit For ISDN(Q.931) Circuits

2.6.3.2 Map


Unique ID for mapping Circuit onto the ISUP Stack. Must be unique per Originating Point on the

System.



ISUP Circuits Read Write

Integer

2.6.3.3 Interface


Defines the TDM Interface the circuit is assigned to



All Circuits Read Resource Identifier



Write

2.6.3.4 Cic


Defines the CIC value for the circuit within its Routeset



All ISUP Circuits Read Write

Integer

2.6.3.5 Controlling


Defines the controlling end in the case of glare calls.




Drop Down List

2.6.3.5.3 Values

Value Description

Controlling This circuit is controlling

Non Controlling This circuit is not controlling

Odd Controlling This circuit is controlling if its CIC value is Odd

Even Controlling This circuit is controlling if its CIC value is Even

2.6.3.6 Actual Controlling


Shows the actual controlling status based on the setting defined in the Controlling attribute



All ISUP Circuits Read User String

2.6.3.6.3 Values

Value Description

Controlling This circuit is controlling

Non Controlling This circuit is not controlling

2.6.3.7 Direction


Defines if the circuit can accept, make or allow calls in both directions



All Read Write

Dropdown List



2.6.3.7.3 Values

Value Description

Bothway Allow calls in either direction

Incoming Circuit will not be selected for outgoing calls

Outgoing Circuit will not accept any incoming calls

2.6.3.8 Timeslot


Defines the Media Timeslot on the TDM Interface this Circuit is assigned to.




Integer

2.6.3.9 SetupTotal


Count of number of outgoing call setup attempts made on the circuit. Used in conjunction with

‘COT Frequency’ attribute on ‘SS7 Stack’ resource.



All ISUP Circuits Read Integer

2.6.3.10 CircuitGroup


Defines the Circuit Group resource this Circuit is part of (for use with Circuit Group

Blocking/Unblocking).




Resource Identifier

2.6.3.11 Partner


Defines the Partner Circuit resource when using Drop/Insert Routing.




Resource Identifier

2.6.3.12 Stack


Defines the SS7 Stack resource for the ISUP Routeset.




Resource Identifier



2.6.3.13 CallControl


Defines the Call Control resource assigned to this Circuit.




Resource Identifier

2.6.3.14 DCall


End of Life

2.6.3.15 Datalink


Defines the ISDN Datalink resource assigned to this Circuit.



ISDN Circuits Read Write No-Default

Resource Identifier

2.6.3.16 COT Success


Time at which the circuit last had a successful COT Test.



All ISUP Circuits Read String

2.6.3.17 CC Status


Displays the current call control status of the Circuit.



All Circuits Read User String

2.6.3.17.3 Values

Value Description

CC_IDLE Idle. Circuit record not in use.

IC_WAIT_COT Incoming call requested COT test. Waiting for COT message with success for failure.

IC_WAIT_DIGITS Waiting to collect all digits from subsequence SAM messages for overlap call.

IC_SEIZE Circuit is in use for incoming call but call has not yet been routed.

IC_WAIT_ACCEPTED Incoming Call Wait for Accepted message.



Waiting for Accepted message from outgoing call

IC_WAIT_ANSWER Incoming Call Wait for Answer message. Waiting for Answer message from outgoing call

IC_WAIT_BWD_MSG Incoming Call Wait for backward message. Waiting for any response from outgoing call.

IC_CCR_TEST Incoming Call. Running CCR test.

IC_COLLECT_DIGITS Waiting to collect all digits from subsequence SAM messages for overlap call.

IC_SUSPEND Suspended Incoming Call

CC_ANSWER Answered Call

CC_WAIT_CHANNEL_FREE Waiting for Channel Free message before clearing circuit

CC_WAIT_TRANSIT_CHANNEL_FREE Waiting for Channel Free message before clearing circuit

CC_WAIT_BWD_CLEAR Waiting for backwards clear message

CC_WAIT_DISCRESP Waiting for response to disconnect request

CC_WAIT_TRANSIT_DISCRESP Waiting for response to disconnect request

CC_WAIT_BWD_CLEAR_DISCRESP Waiting for response to disconnect request from a backwards clear message

CC_IDLE_WAIT_DISCRESP Waiting for response to disconnect request before going IDLE

IC_SEIZE_WAIT_DISCRESP Waiting for response to disconnect request whilst attempting to route

OG_WAIT_CALL_PROGRESS Outgoing Call Wait for Process message. Waiting for Process message from outgoing call

OG_WAIT_ANSWER Outgoing call Wait for Answer. Waiting for ISUP ANM or ISDN CONNECT message.

OG_WAIT_BWD_MSG Outgoing Call Wait for backward message. Waiting for any response from outgoing call.

OG_WAIT_DIGITS Outgoing call. Sent initial IAM message but may be further digits in subsequent SAMs to be received

OG_WAIT_SETUP_ACK Outgoing Call Waiting for acknowledge to Setup message.

OG_SUSPEND Suspended Outgoing Call

OG_WAIT_ACCEPTED Outgoing call Wait for Answer. Waiting for ISUP ACM or ISDN ALERTING message.

OG_CCR_TEST Outgoing Call. Running CCR test.

IC_WAIT_SPEECH_PATH_CONNECT Incoming Call. Waiting for media connection to be setup

OG_WAIT_SPEECH_PATH_CONNECT Outgoing Call. Waiting for media connection to be setup

IC_SEIZE_GET_ROUTE Waiting for response to external routing request (e.g. SQL server)

CC_TRANSFER_NOTIFY Call is being transferred. In this state whilst negotiating with third leg.

IC_WAIT_CNAM_RSP Incoming call. Waiting for response to a CNAM, LNP, 800 or LIDB

IC_PLAY_ANN_PENDING_CLEAR Incoming Call. Playing announcement before clearing

IC_WAIT_TIMER_EXPIRY_B4_PLAY_ANN Incoming Call. Waiting for timer to expire before the SVI can play an announcement

IC_WAIT_SPCH_PTH_CNCT_B4_PLAY_ANN Incoming Call. Waiting for the media path to be setup before the SVI can play an announcement

IC_WAIT_SPCH_CNCT_B4_DISC Incoming Call. Waiting for media connection to be setup, then will disconnect. Occurs when call is cleared whilst media connection is being



setup

OG_WAIT_SPCH_CNCT_B4_DISC Outgoing Call. Waiting for media connection to be setup, then will disconnect. Occurs when call is cleared whilst media connection is being setup

IC_WAIT_TIMER_EXPIRY_B4_PLAY_ANN_OG_SETUP Incoming Call. Waiting for the media path to be setup before the SVI can play an announcement before sending Outgoing call setup message

IC_WAIT_SPCH_PATH_B4_PLAY_ANN_OG_SETUP Incoming Call. Waiting for the media path to be setup before the SVI can play an announcement before sending Outgoing call setup message

IC_WAIT_TIMER_AND_SPCH_CNT_B4_PLAY_ANN Incoming Call. Waiting for timer to expire before for the media path to be setup before the SVI can play an announcement

IC_PLAY_ANN_B4_OG_SETUP Incoming Call. Playing announcement before sending Outgoing call setup message

IC_PARTIAL_MATCH Incoming Call. Call has provided a partial match in the routing for an overlap call which has not received all digits.

OG_PLAY_ANN_ALLOCATED Outgoing Call.

CC_LI_ALLOCATED Lawful Intercept call.

CC_COT_TEST COT Test in progress

IC_SEIZE_TRANSLATE_NUMBER_REQ Incoming Call. Waiting for response from a number translation request

CC_THROTTLED Call throttled at ISUP, will revert other state when

2.6.3.18 Initialise


End Of Life

2.6.3.19 Block State


Displays the current status of the circuit blocks.




User String

2.6.3.19.3 Values

Value Description

IDLE Available for use

MBLK Maintenance Blocked

LBLK Locally Blocked

RBLK Remotely Blocked

MBLK-RBLK Maintenance and Remotely Blocked

LBLK-RBLK Locally and Remotely Blocked

MBLK-LBLK Maintenance and Locally Blocked

MBLK-LBLK-RBLK Maintenance, Locally and Remotely Blocked



2.6.3.20 Options


Circuit resource specific options.



All Circuits Read Write No-Default

Bit Mask Flag

2.6.3.20.3 Values

Value Description

SNMP-Trap Generate SNMP traps for this resource.

UCIC Indicates that a UCIC message was received on this circuit from far end.

2.6.3.21 send CVT


Generate a CVT message on this circuit.

2.6.3.22 Send CQM


Generate a CQM message on this circuit.

2.7 Circuit Group

2.7.1 Description

Resource used to group ISUP Circuits together for the purposes of Group Block/Reset.

2.7.2 Products

SVI-MG | SVI-MGC | SVI-9225 | SVI-9220.

2.7.3 Attributes

2.7.3.1 Type





All Read Write

Dropdown List

2.7.3.1.3 Values

Value Description

ISUP Circuit Group Defines as ISUP Circuit Group Type



2.7.3.2 Card


End of Life.

2.7.3.3 Map


End of Life.

2.7.3.4 TupFlags


End Of Life.

2.7.3.5 Priority


End Of Life.

2.7.3.6 Tcg


Timer between receipt of BLO/UBL and sending CGB/CGU.



All Read Write

Integer

2.7.3.7 Start Circuit


First Circuit in the Group.




Resource Identifier

2.7.3.8 Last Circuit


Last Circuit in the Group.




Resource Identifier

2.7.3.9 Range


Number of circuit in the group. Set automatically based on Start/Last values.





All Read

Integer

2.7.3.10 Stack


The SS7 Stack resource the circuits are assigned to.



All Circuit Groups Read Write

Resource Identifier

2.7.3.11 Interface


The TDM Interface the circuits are assigned to.



All Circuit Groups Read Write

Resource Identifier

2.7.3.12 CGRS State


Sets the behaviour regarding Circuit Group Reset messages in this Circuit Group. Updated

automatically based on Circuit Group state.



All Circuit Groups Read Drop Down List

2.7.3.12.3 Values

Value Description

Can Send Can send CGRS

Cant Send Cannot send CGRS

Never Send Never send CGRS

2.8 Originating Point

2.8.1 Description

Defines the originating point of the SS7 interconnect.

2.8.2 Products SVI-MG | SVI-MGC | SVI-9225 | SVI-9220 | SVI-STP | SVI-SMSC | SVI-SG

2.8.3 Attributes

2.8.3.1 Type







All Read Write

Drop Down List

2.8.3.1.3 Values

Value Description

SS7 Originating Point Defines as SS7 Originating Point

SIGTRAN Originating Point As SS7 Originating Point

2.8.3.2 Protocol


Sets the base standard for the originating point.



All Applied Read Write

Drop Down List

2.8.3.2.3 Values

Value Description

ETSI Sets base as ETSI

ITU Sets base as ITU

ANSI Sets bases as ANSI

TUP Sets base as TUP

TTC Sets base as TTC

China Sets base as China

2.8.3.3 STPMode


Sets the Originating Point STP Mode for special point code routing/presentation scenarios.




Drop Down List

2.8.3.3.3 Values

Value Description

None No special mode applied

Partial Partial Point Code mode applied

Full Full Point Code mode applied

2.8.3.4 Pointcode


Contains the originating pointcode (decimal). 2.8.3.4.2 Definition



Integer



2.8.3.5 Ni


Network Indicator of the route




Integer

2.8.3.5.3 Values

Value Description

0 International

1 International (Spare)

2 National

3 National (Spare)

2.8.3.6 Debug


End Of Life

2.8.3.7 Info


Displays detailed MTP Layer 3 info about Originating Point in OAM (not available in SVI_MS)



All Write N/A

2.8.3.8 Setdebug


End of Life

2.8.3.9 Retrieval Persistent


End of Life

2.8.3.10 L3Timers


Defines the MTPL3 Timer Resource in the case that the default timers need to be overridden.




Resource Identifier

2.8.3.11 MTP Route Via DPC Pointcodes


For the STP if set to Override the OPC and DPC for the outgoing message will be overwritten with

the point code for the destination and the point code of the originating point. If set to Leave then

the incoming point codes will be used (unless they have been translated).



The Destination Point value for this flag will take preference unless set to Ignore or not set.



All Read Write

Byte

2.8.3.11.3 Values

Value Description

0 Ignore

1 Leave

2 Override

2.9 Destination Point

2.9.1 Description

Defines the destination points of an SS7 signalling interconnect.

2.9.2 Products SVI-MG | SVI-MGC | SVI-9225 | SVI-9220 | SVI-STP | SVI-SMSC | SVI-SG

2.9.3 Attributes

2.9.3.1 Type





All Read Write

Drop Down List

2.9.3.1.3 Values

Value Description

SS7 Destination Point Set as type SS7 Destination Point

IPSP Destination Point For use with M3UA IPSP Interconnects

ISUP Destination Point As SS7 Destination Point

2.9.3.2 Originating


Specifies the instance of the originating point that the destination is associated to. 2.9.3.2.2 Definition


All Read Write

Resource Identifier

2.9.3.3 Pointcode


Contains the pointcode of the destination point (decimal). 2.9.3.3.2 Definition





Integer

2.9.3.4 Ni


Contains the Network Indicator of the destination point. 2.9.3.4.2 Definition



Integer

2.9.3.4.3 Values

Value Description

0 International


2 National

3 National (Spare)

2.9.3.5 Primary


This indicates the primary linkset that the destination is connected to 2.9.3.5.2 Definition


All Read Write

Resource Identifier

2.9.3.6 Secondary


If a linkset is connected to a secondary linkset this attribute contains the linkset resource instance which is the secondary route. 2.9.3.6.2 Definition


All Read Write

Resource Identifier

2.9.3.7 Loadshare


To load share between routes.



All Read Write

Boolean





The Linksets which will have TFX messages sent on should this Destination Point change state.



All Read Resource Identifier

2.9.3.9 Sls


Used for SCCP Load sharing. Updated automatically.



All Read Integer

2.9.3.10 Clink


The Linkset which is the C-Link for this Destination Point



All Read Write

Resource Identifier

2.9.3.11 Max Msg/s


Statistic showing the maximum messages/second since system start




Integer

2.9.3.12 Msg/s


Statistic showing the real-time messages/second




Integer



2.9.3.13 RQue


Used for MTPL3 throttling. Updated automatically.



All Read No-Default

Integer

2.9.3.14 ASP


End of Life.

2.9.3.15 AS


For M3UA the AS resource this Destination Point is available via.



All Read Write

Resource identifier

2.9.3.16 MTP Route Via DPC Pointcodes


For the STP if set to Override the OPC and DPC for the outgoing message will be overwritten with

the point code for the destination and the point code of the originating point. If set to Leave then

the incoming point codes will be used (unless they have been translated)



All Read Write

Byte

2.9.3.16.3 Values

Value Description

0 Ignore

1 Leave

2 Override

2.10 Linkset

2.10.1 Description Defines the Linkset or Adjacent point of the SS7 interconnect.

2.10.2 Products

SVI-MG | SVI-MGC | SVI-9225 | SVI-9220 | SVI-STP | SVI-SMSC | SVI-SG.



2.10.3 Attributes

2.10.3.1 Type





All Read Write

Drop Down List

2.10.3.1.3 Values

Value Description

SS7 Linkset Defines as SS7 Linkset

2.10.3.2 Map


End of Life

2.10.3.3 Originating


Specifies the instance of the originating point resource that the linkset is associated to.



All Read Write

Resource Identifier

2.10.3.4 Pointcode


Pointcode of the adjacent point (decimal).




Integer

2.10.3.5 Ni


Network indicator of the adjacent point.




Integer

2.10.3.5.3 Values

Value Description

0 International


2 National

3 National (Spare)



2.10.3.6 Combined


If the linkset is part of a combined linkset this value is set to the resource instance of the combined linkset, else it is set to the value of this linksets instance.



All Applied Read Write No-Default

Resource Link

2.10.3.7 TFx Required


If true Destination Points will not be set as available via this Linkset until a TFA is explicitly

received after the Linkset is available.



All Read Write

Boolean

2.10.3.7.3 Values

Value Description

False Destination Points are presumed available when Linkset is available

True Destination Points are presumed unavailable until notified by TFA



A list of destination point resources the linkset is interested to know the status through TFP/TFA

mechanism.

2.10.3.9 Add MTP Routes


Attach MTP Route resources which will be used for MTP Layer 3 routing rules on this linkset.




Resource Link

2.10.3.10 MTP CDR


End of Life

2.10.3.11 Tx MSU Total

2.10.3.11.1 Description Statistic showing total number of MSU’s sent since system start.






2.10.3.12 Tx MSU Sec

2.10.3.12.1 Description Statistic showing real-time MSU/Second being sent.




2.10.3.13 Tx MSU Sec Max

2.10.3.13.1 Description Statistic showing maximum MSU/Second send rate since system start.




2.10.3.14 Rx MSU Total

2.10.3.14.1 Description Statistic showing total number of MSU’s received since system start.




2.10.3.15 Rx MSU Sec

2.10.3.15.1 Description Statistic showing real-time MSU/Second being received.




2.10.3.16 Rx MSU Sec Max

2.10.3.16.1 Description Statistic showing maximum MSU/Second receive rate since system start.




2.10.3.17 Tx Bits Total

2.10.3.17.1 Description Statistic showing total number of Bit’s sent since system start.






2.10.3.18 Tx Bits Sec

2.10.3.18.1 Description Statistic showing real-time Bit/Second being sent.




2.10.3.19 Tx Bits Sec Max

2.10.3.19.1 Description Statistic showing maximum Bit/Second send rate since system start.




2.10.3.20 Rx Bits Total

2.10.3.20.1 Description Statistic showing total number of Bit’s received since system start.




2.10.3.21 Rx Bits Sec

2.10.3.21.1 Description Statistic showing real-time Bit/Second being received.




2.10.3.22 Rx Bits Sec Max

2.10.3.22.1 Description Statistic showing maximum Bit/Second receive rate since system start.




2.10.3.23 COO Bis


End Of Life.



2.10.3.24 IC L3Label


Range of L3 Label resources to examine when routing messages from this Linkset.



All links Read / Write String

2.10.3.24.3 Values

Value Description

Range of Resource instances

2.10.3.25 OG L3Label


Range of L3 Label resources to examine when routing messages to this Linkset.



All Links Read / Write String

2.10.3.25.3 Values

Value Description


2.10.3.26 M3UA AS


Specifies the instance of the AS resource that the linkset is associated to. Only applicable to M3UA configuration.



All Read Write

Resource Identifier

2.10.3.27 SSME XML


Specifies the instance of the XML resource that the linkset is associated to. Used to apply an xml based configuration for message routing and manipulation.



All Read Write

Resource Identifier

2.10.3.28 Tx Bits Throttle

2.10.3.28.1 Description Statistic showing real-time Bit/Second throttling.



All Linksets Read Integer



2.10.3.29 Tx MSU Throttle

2.10.3.29.1 Description Statistic showing real-time MSU/Second throttling.




2.10.3.30 Tx Congestion

2.10.3.30.1 Description Statistic showing number of times congestion was entered.




2.10.3.31 Tx Failure

2.10.3.31.1 Description Statistic showing number of failures.




2.10.3.32 Routing Failures

2.10.3.32.1 Description Statistic showing number of failures happened while attempting to process an incoming packet.




2.10.3.33 Rx UDTS

2.10.3.33.1 Description Statistic showing number of UDTS messages received.






2.11 SS7 Stack

2.11.1 Description

Resource used to define the Routset and Layer 4 (ISUP/SCCP) capabilities.

2.11.2 Products

SVI-MG | SVI-MGC | SVI-9225 | SVI-9220 | SVI-STP | SVI-SMSC | SVI-SG.

2.11.3 Attributes

2.11.3.1 Type




All Read Write

Dropdown List

2.11.3.1.3 Values

Value Description

ISUP Stack For ITU/ETSI based variants of ISUP

IUP Stack For IUP(BTNUP)

TUP Stack For TUP

ANSI Stack For ANSI ISUP

SCTP For SCCP Passthrough to M3UA Mode

SCCP Router Stack For SCCP Routing Mode

2.11.3.2 Map

2.11.3.2.1 Description End Of Life.

2.11.3.3 MTPL3

2.11.3.3.1 Description Defines if the internal MTP Layer 3 stack is to be used, or external or M3UA (no MTP Layer 3).



All Read Write

Dropdown List

2.11.3.3.3 Values

Value Description

Internal Use the Internal Stack

External Use an External Stack (no longer used)

M3UA Use M3UA

2.11.3.4 MTPL4




Defines if the internal ISUP stack is to be used or external.



All ISUP Read Write

Dropdown List

2.11.3.4.3 Values

Value Description

Internal Use Internal Stack

External Use External Stack (No longer used)

2.11.3.5 Originating Point

2.11.3.5.1 Description Links to the Originating Point Resource for the routeset.



All Read Write

Resource Identifier

2.11.3.6 Destination Point

2.11.3.6.1 Description Links to the Destination Point Resource for the routeset.



All Read Write

Resource Identifier

2.11.3.7 IP

2.11.3.7.1 Description End Of Life.

2.11.3.8 AS

2.11.3.8.1 Description For SCTP Type sets the M3UA AS the SCCP will pass through to.



All Read Write

Resource Identifier

2.11.3.9 SIO

2.11.3.9.1 Description Sets the Service Indicator for the Stack.





All Read Write

Integer

2.11.3.9.3 Values

Value Description

3 SCCP

5 ISUP

2.11.3.10 IUP ISDN

2.11.3.10.1 Description Sets the behaviour for ISUP call types.



All IUP Read Write

Dropdown List

2.11.3.10.3 Values

Value Description

Map ISDN Map ISDN (Default)

Reject Reject the call

Map Telephony Map Telephony

2.11.3.11 IUP ACI Request

2.11.3.11.1 Description Sets the type of information requested when ACI is sent.



All IUP Read Write

Dropdown List

2.11.3.11.3 Values

Value Description

None None

Full Calling Full Calling Number

Full Forward Full Forwarding Number

Full Calling and Forward

Full Calling and Forwarding Numbers

Presentation Presentation Number

Presentation and Full Presentation and Full Calling Numbers

Presentation and Forward

Presentation and Forwarding Numbers

Presentation and Forward and Full

Presentation, Full Calling and Forwarding Numbers



2.11.3.12 IUP ASUI Type

2.11.3.12.1 Description Sets the type of ASUI for IUP.



All IUP Read Write

Dropdown List

2.11.3.12.3 Values

Value Description

Type 1 Full Full numbers requested (default)

Type 2 Partial Partial numbers requested

2.11.3.13 IUP No OLI

2.11.3.13.1 Description Set behaviour for OLI in IUP.



All IUP Read Write

Dropdown List

2.11.3.13.3 Values

Value Description

Request OLI Request OLI (default)

Send Partial Request partial OLI

Send No OLI Do not send OLI

2.11.3.14 ISUP T13

2.11.3.14.1 Description Set ISUP Timer 13 (default 300 second).



All ISUP Read Write

Integer

2.11.3.15 ISUP T21




All ISUP Read Write

Integer

2.11.3.16 ISUP T24






All ISUP Read Write

Integer

2.11.3.17 ISUP T25




All ISUP Read Write

Integer

2.11.3.18 ISUP Timers

2.11.3.18.1 Description Link to Timer resource for setting of all ISUP Timers.



All ISUP Read Write

Resource Identifier

2.11.3.19 PCLI

2.11.3.19.1 Description Set Partial CLI to be presented if requested by network.



All IUP Read Write

Integer

2.11.3.20 Protocol

2.11.3.20.1 Description Set the specific ISUP protocol used.



All ISUP Read Write

Dropdown List

2.11.3.20.3 Values

Value Description

ITU White Book ITU White Book

ITU Blue Book ITU Blue Book

ANSI ANSI

French SPIROU French SPIROU

Uk isup Uk isup

Finnish ISUP Finnish ISUP



2.11.3.21 COTFrequency

2.11.3.21.1 Description Set the frequency of how often a COT test should be preformed per number of call attempts.



All ISUP Read Write

Integer

2.11.3.22 Network Appearance

2.11.3.22.1 Description End Of Life

2.11.3.23 Options

2.11.3.23.1 Description Set specific options on the SS7 Stack.




Bit Mask Flag

2.11.3.23.3 Values

Value Description

None None

Ignore-Process End Of Life

SS7 Accelerated Assumes Local Blocks are available without UBL/UBA exchange

Route SST Route SCCP SST messages rather then terminate them

Include Appearance End Of Life

2.11.3.24 Service

2.11.3.24.1 Description Set the high level service type.



All SCCP Read Write

Dropdown List

2.11.3.24.3 Values

Value Description

Map Map

TCAP TCAP

2.11.3.25 ACC DrateStart

2.11.3.25.1 Description Sets the Start Percentage for decreasing traffic rate (default 5).





All UK ISUP Read Write

Integer

2.11.3.26 ACC DrateEnd

2.11.3.26.1 Description Sets the maximum percentage for decreasing traffic rate (default 10).




Integer

2.11.3.27 ACC Drate

2.11.3.27.1 Description Current percentage being used to decrease traffic rate.



All UK ISUP Read No-Secure

Integer

2.11.3.28 ACC Irate

2.11.3.28.1 Description Percentage to be being used to increase traffic rate (default 10).




Integer

2.11.3.29 ACC Max

2.11.3.29.1 Description Calls per second rate at which to trigger ACC.




Integer

2.11.3.30 ACC Min

2.11.3.30.1 Description Calls per second rate at which to allow traffic increase (disable ACC).






Integer

2.11.3.31 ACC Throttle

2.11.3.31.1 Description Current call/second throttle applied to outgoing traffic.




Integer

2.11.3.32 ACC Congestion

2.11.3.32.1 Description Flag to show if ACC is currently being applied.




Boolean

2.11.3.33 ACC Apply

2.11.3.33.1 Description Flag to configure if ACC should be used on this route.




Boolean

2.11.3.34 ACC Tabate

2.11.3.34.1 Description Configurable Timer that monitors if congestion has abated and ACC can be removed. This requires

consecutive samples to be below the min REL rate for time Tabate.




Integer

2.11.3.35 ACC Sample

2.11.3.35.1 Description Result of the current sample.




Integer



2.11.3.36 ACC Statistics

2.11.3.36.1 Description Link to Statistics resource to allow more monitoring.




Resource Identifier

2.11.3.37 Service GT

2.11.3.37.1 Description Sets the calling party digits for the SCCP and the GMSC Address for SRI Lookups only



SRI Lookup Read Write

User String

2.11.3.38 Pass-Through-TCAP

2.11.3.38.1 Description For InitialDp allows the SCCP Data to be passed through the TCAP Stack unchanged



Pass-Through-TCAP Read Write

Byte

2.11.3.39 CAP SSN

2.11.3.39.1 Description List of Subsystem Numbers (SSN) that needs to be considered as CAMEL Subsystem numbers.



CAP SSN Read Write

Integer

2.11.3.40 CAMEL Phases

2.11.3.40.1 Description Set the supported CAMEL Phases value to be sent in Send Routing Info (SRI) request sent out.



All SCCP doing SRI Read Write

Dropdown List

2.11.3.40.3 Values

Value Description

None CamelInfo parameter not sent in SRI request

Phase 1 CAMEL Phase 1 support indication



Phase 2 CAMEL Phase 1 and 2 support indication

Phase 3 CAMEL Phase 1,2 and 3 support indication

Phase 4 CAMEL Phase 1,2,3 and 4 support indication

2.11.3.41 INAP Application Context

2.11.3.41.1 Description Set the application context value that needs to be used in INAP Initial DP message sent out.



All SCCP doing INAP IDP Read Write

Free text application context

2.11.3.42 Ignore API Client

2.11.3.42.1 Description Enable routing of all messages on this stack to the callcontrol task ignoring any API Client tasks

available to process the message.



All SCCP Read Write

Boolean

2.12 MTP Route

2.12.1 Description

Resource used to define the Routeset and Layer 4 (ISUP/SCCP) capabilities.

2.12.2 Products

SVI-STP

2.12.3 Attributes

2.12.3.1 OPC

2.12.3.1.1 Description Is the OPC present.


Value Description



Match to defined

Present The OPC is expected to be Present

Not Present The OPC is expected not to be present

2.12.3.2 DPC

2.12.3.2.1 Description Is the DPC present.


Value Description

Match to defined

Present The DPC is expected to be Present

Not Present The DPC is expected not to be present

2.12.3.3 NI


Network Indicator of the MTP route.




Integer

2.12.3.3.3 Values

Value Description

0 International


2 National

3 National (Spare)

2.12.3.4 SIO

2.12.3.4.1 Description Sets the Service Indicator for the MTP route.



All Read Write

Integer

2.12.3.4.3 Values

Value Description

3 SCCP

5 ISUP

2.12.3.5 Linkset

2.12.3.5.1 Description Indicates the instance of the linkset resource for which this linkset is associated to.






Resource Identifier

2.12.3.6 L3Message

2.12.3.6.1 Description The value of the message you wish to match, number is an integer but must be converted to hex.




Integer

2.12.3.7 Set_OPC


Specifies the instance of the originating point that the destination is associated to. 2.12.3.7.2 Definition


All Read Write

Resource Identifier

2.12.3.8 Set_DPC

Specifies the instance of the destination point that the destination is associated to.



All Read Write

Resource Identifier

2.12.3.9 Set_NI


Network Indicator of the route.




Integer

2.12.3.10 Route

The Linkset which should be used to Route to.

(When in loadshare) - The route which should be used when the SLC is even.

2.12.3.11 Destination

The destination Point you wish to Route to.



2.12.3.12 Secondary

The linkset which should be used if the primary is unavailable.

(When in loadshare) - The route which should be used when the SLC is odd.

2.12.3.13 AS Route

2.12.3.13.1 Description The M3UA AS to route to (primary) (when in loadshare) – route used when SLC is even.



M3UA Links Read Write

Resource Identifier

2.12.3.14 AS Route Sec

2.12.3.14.1 Description The M3UA AS to route to (secondary) (when in loadshare) – route used when SLC is odd.



M3UA Links Read Write

Resource Identifier

2.12.3.15 Layer 4 Db

End Of Life.

2.12.3.16 Call Control

Defines the Call Control resource assigned to this Circuit.




Resource Identifier

2.12.3.17 Options




Bit Mask Flag

2.12.3.17.2 Values

Value Description

Loadshare Use load sharing between Route and secondary

None None




2.12.3.18 In CIC Low


Matches all ISUP CIC’s above this number.




Integer

2.12.3.19 In CIC High

Matches all ISUP CIC’s below this number.




Integer

2.12.3.20 Out CIC low

Only used when “In CIC Low” configured.

Set’s the outgoing CIC to be as follows:

Out CIC low + (In CIC - In CIC low).

2.12.3.21 Out CIC High

End Of Life.

2.13 SCTP

2.13.1 Description

Creates and maintains an SCTP socket for the use of M3UA/M2PA/M2UA etc.

2.13.2 Products

SVI-MG | SVI-MGC | SVI-STP | SVI-SMSC | SVI-SG.

2.13.3 Attributes

2.13.3.1 Type




All Read Write

Resource



2.13.3.1.3 Values

Value Description

SCTP SCTP Socket

2.13.3.2 ASP

2.13.3.2.1 Description The ASP Resource associated with this SCTP socket.



All Read Write

Resource Identifier

2.13.3.3 Local Port

2.13.3.3.1 Description The SCTP port number for the local SVI process.



All Read Write

Integer

2.13.3.3.3 Values

Value Description

2905 Standard SCTP port

Other values

2.13.3.4 Local Address

2.13.3.4.1 Description IP address of the SVI-SG for the SCTP socket.



All Read Write No-Default No-Secure

String

2.13.3.4.3 Values

Value Description

IP Address

2.13.3.5 Remote Port

2.13.3.5.1 Description SCTP port number for the remote host.



All Read Write

Integer



2.13.3.5.3 Values

Value Description

2905 Standard SCTP port

Other values

2.13.3.6 Remote Address

2.13.3.6.1 Description IP Address for the remote host.




String

2.13.3.6.3 Values

Value Description

IP Address

2.13.3.7 Outgoing Streams

2.13.3.7.1 Description Number of outgoing SCTP streams for this socket.



All Read Write

Integer

2.13.3.7.3 Values

Value Description

2

2.13.3.8 Incoming Streams

2.13.3.8.1 Description Number of incoming SCTP streams for this socket.



All Read Write

Integer

2.13.3.8.3 Values

Value Description

2

2.13.3.9 End

2.13.3.9.1 Description Controls the client-server behaviour of the SCTP socket.





All Read Write

Drop-down list

2.13.3.9.3 Values

Value Description

Server

Client

IPSP M3UA only

2.13.3.10 Protocol

2.13.3.10.1 Description Allows TCP-IP sockets to be used instead of SCTP.



All Read Write

Drop Down list

2.13.3.10.3 Values

Value Description

TCP Uses a TCP/IP connection instead of SCTP

SCTP SCTP socket

2.13.3.11 IP

2.13.3.11.1 Description When using TCP/IP instead of SCTP (section 0), This is the IP socket resource to use.



SCTP over TCP/IP only Read Write No-Default No-Secure

Resource

2.13.3.12 Redundancy Model

2.13.3.12.1 Description Controls the behaviour of the SCTP socket in a redundant system.



All Read Write

Drop-Down list

2.13.3.12.3 Values

Value Description

Active The standby SCTP socket will be Activated

Inactive The standby SCTP will not be activated until Failover

Independent The SCTP will not depend on the plane in a redundant system



2.13.3.13 Multi-homed Local Address

2.13.3.13.1 Description Alternate local address for Multi-homed system.



Multi-homed systems Read Write No-Default No-Secure

String

2.13.3.13.3 Values

Value Description

IP Address

2.13.3.14 Multi-homed Remote Address

2.13.3.14.1 Description Alternate Remote address for Multi-homed system.



Multi-homed systems Read Write No-Default

String

2.13.3.14.3 Values

Value Description

IP Address

2.13.3.15 SCTP State

2.13.3.15.1 Description Internal SVI SCTP state.



none Read Integer

2.13.3.16 SCTP Tmax

2.13.3.16.1 Description Retransmission Timeout Value in milliseconds.




Integer

2.13.3.16.3 Values

Value Description



2000 (default) 2 seconds

2.13.3.17 SCTP Heartbeat

2.13.3.17.1 Description Heartbeat interval timeout in milliseconds.




Integer

2.13.3.17.3 Values

Value Description

5000 (default) 5 seconds

2.13.3.18 SCTP Max Retry

2.13.3.18.1 Description Maximum number of retransmissions before ‘unreachable’.




Integer

2.13.3.18.3 Values

Value Description

2 (default)

2.13.3.19 Fd / Sktfd

2.13.3.19.1 Description The internal file handles of the SCTP socket.



All Read No-Secure No-Init

Integer

2.13.3.19.3 Values

Value Description

System-set

2.13.3.20 No Delay

2.13.3.20.1 Description Allows the setting of the SCTP socket option ‘SCTP_NODELAY’.



All Read Drop-down list



Write

2.13.3.20.3 Values

Value Description

On SCTP_NO_DELAY set

Off SCTP_NO_DELAY not set

2.13.3.21 Tx Msg Total

2.13.3.21.1 Description Statistic showing total number of Messages sent since system start.



All Sctp Read Integer

2.13.3.22 Tx Msg/Sec

2.13.3.22.1 Description Statistic showing real-time Messages/Second being sent.




2.13.3.23 Tx Msg/Sec Max

2.13.3.23.1 Description Statistic showing maximum Messages/Second send rate since system start.



All SCTP Read Integer

2.13.3.24 Rx Msg Total

2.13.3.24.1 Description Statistic showing total number of Messages received since system start.




2.13.3.25 Rx Msg/Sec

2.13.3.25.1 Description Statistic showing real-time Messages/Second being received.






2.13.3.26 Rx Msg/Sec Max

2.13.3.26.1 Description Statistic showing maximum Messages/Second receive rate since system start.




2.13.3.27 Tx Bytes Total

2.13.3.27.1 Description Statistic showing total number of Bytes sent since system start.




2.13.3.28 Tx Bytes/Sec

2.13.3.28.1 Description Statistic showing real-time Bytes/Second being sent




2.13.3.29 Tx Bytes/Sec Max

2.13.3.29.1 Description Statistic showing maximum Bytes/Second send rate since system start




2.13.3.30 Rx Bytes Total

2.13.3.30.1 Description Statistic showing total number of Bytes received since system start




2.13.3.31 Rx Bytes/Sec

2.13.3.31.1 Description Statistic showing real-time Bytes/Second being received






2.13.3.32 Rx Bytes/Sec Max

2.13.3.32.1 Description Statistic showing maximum Bytes/Second receive rate since system start




2.13.3.33 Rx Bytes/Sec Throttle

2.13.3.33.1 Description If the number of bytes per second threshold is exceeded then the SCTP will be throttled until the

next second. The SCTP link will queue the received SCTP messages



All SCTP Write Integer

2.13.3.34 Rx Msgs/Sec Throttle

2.13.3.34.1 Description If the number of messages per second threshold is exceeded then the SCTP will be throttled until

the next second. The SCTP link will queue the received SCTP messages



All Sctp Write Integer

2.13.3.35 Rx Bytes/Sec Max Queue

2.13.3.35.1 Description Number of SCTP messages to be queued after throttle before discard



All Sctp Write Integer

2.13.3.36 Options

2.13.3.36.1 Description SCTP options.




List

2.13.3.36.3 Values

Value Description

SNMP-Trap

Listener



Validate-Addr

SO_REUSEADDR Socket option SO_REUSEADDR will be set on sockets opened for this resource

Abort-Connection-On-Close

When connection is closed SCTP ABORT will be sent rather than SHUTDOWN

Allow-Duplicate-Local-Addr-Port

Normally the SVI will check the local address-port is unique for all SCTP resources; this option skips the check for this resource

Monitor This SCTP resource is a monitor-only device

Pcap-No-SaveFile-Delay

Monitor only - Packets from a Test Pcap File are processed as quickly as possibly rather than being processed in 'real' time

Pcap-SaveFile-Preserve-Ass

Monitor only - When a Test Pcap File is loaded, any Association data will be preserved rather than deleted (default is deletion)

2.14 ASP

2.14.1 Description

Defines the ASP in a SIGTRAN configuration.

2.14.2 Products


2.14.3 Attributes

2.14.3.1 Type




All Read Write

Drop Down List

2.14.3.1.3 Values

Value Description

ASP ASP

SS7Cisco ASP For Cisco Session manager connection

2.14.3.2 SCTP

2.14.3.2.1 Description The SCTP resource used by this ASP.



All Read Write

Resource

2.14.3.3 Identifier




Identifier used in ASP UP/ NOTIFY messages.



All Read Write

Integer

2.14.3.3.3 Values

Value Description

32-bit

2.14.3.4 Protocol

2.14.3.4.1 Description The SIGTRAN protocol.



ALL Read Write

Drop Down List

2.14.3.4.3 Values

Value Description

M3UA

M2UA

M2PA

IUA

SLT

2.14.3.5 End

2.14.3.5.1 Description The Protocol End.



All Read Write

Drop Down List

2.14.3.5.3 Values

Value Description

Server

Client

IPSP

2.14.3.6 As

2.14.3.6.1 Description The AS associated with this ASP.



All Read Resource



Write

2.14.3.7 Redundancy Model

2.14.3.7.1 Description Controls the behaviour of the ASP in a redundant system.



All Read Write

Drop-Down list

2.14.3.7.3 Values

Value Description

Active The standby ASP will be Activated

Inactive The standby ASP will not be activated until Failover

Independent The ASP will not depend on the plane in a redundant system

2.14.3.8 Include Interface ID

2.14.3.8.1 Description (M2UA only) If set, includes the Interface ID. The value used will be the ‘Interface ID’ setting on the

associated Signalling Link resource.



M2UA only Read Write No-Default

List

2.14.3.8.3 Values

Value Description

On Interface id included in ASPAC and ASPIA messages

Off Interface ID not included

2.14.3.9 Client ASP State

2.14.3.9.1 Description Internal Client state.



All Read No-Secure

Integer

2.14.3.10 Server ASP State

2.14.3.10.1 Description Internal Server State.



All Read Integer



No-Secure

2.14.3.11 Tbeat

2.14.3.11.1 Description Heartbeat timer duration (milliseconds).



All Read Write

Integer

2.14.3.11.3 Values

Value Description

0 (default) No heartbeat

2.14.3.12 TACK

2.14.3.12.1 Description Internal – whether the T_ACK timer is running.



All Read Write No-Default No-Secure

Integer

2.14.3.13 Options

2.14.3.13.1 Description ASP options.




List

2.14.3.13.3 Values

Value Description

Register (Client) Triggers Routing Key registration

SNMP-Trap

UNI-IPSP (Server) Causes ASP to act as a Unidirectional IPSP





All ASP Read Integer
























































2.14.3.25.1 Description If the number of bytes per second threshold is exceeded then the ASP will be throttled until the

next second. The ASP link will queue the received SCTP messages



All ASP Write Integer


2.14.3.26.1 Description If the number of messages per second threshold is exceeded then the ASP will be throttled until the

next second. The ASP link will queue the received ASP messages







2.14.3.27.1 Description Number of ASP messages to be queued after throttle before discard




2.14.3.28 displayRegistrations

2.14.3.28.1 Description Displays the M3UA dynamic routing key registrations against the ASP resource.

2.15 AS

2.15.1 Description

Defines the AS in a SIGTRAN configuration.

2.15.2 Products


2.15.3 Attributes

2.15.3.1 Type




All Read Write

List

2.15.3.1.3 Values

Value Description

M3UA AS

IUA AS

2.15.3.2 Originating Point

Deprecated, End-Of-Life.

2.15.3.3 Destination Point




2.15.3.4 IP Resource


2.15.3.5 ASP


2.15.3.6 Traffic Mode

2.15.3.6.1 Description The AS Traffic Mode.



All Read Write

List

2.15.3.6.3 Values

Value Description

Override Last ASP active is used for all traffic

Loadshare Traffic spread equally over all ASPs

Broadcast All traffic sent using all ASPs

SCCP Routing

2.15.3.7 SCCP DB

2.15.3.7.1 Description SUA –the SCCP Db Resource to be used for routing.



SUA only Read Write No-Default

Resource

2.15.3.8 IC L3Label


Range of L3 Label resources to examine when routing M3UA messages from this AS.



M3UA only Read / Write String

2.15.3.8.3 Values

Value Description


2.15.3.9 OG L3Label


Range of L3 Label resources to examine when routing M3UA messages to this AS.



M3UA only Read / Write String



2.15.3.9.3 Values

Value Description


2.15.3.10 AS State


The internal state of the AS.



All Read List

2.15.3.10.3 Values

Value Description

AS-Inactive

AS-Pending

AS-Active

2.15.3.11 Routing Context Present


Controls SVI M3UA client’s inclusion of ‘Routing Context’ in ASPAC message.



M3UA client Read/Write List

2.15.3.11.3 Values

Value Description

Present ASPAC will include RC set to the value in section 2.15.3.12

Absent ASPAC will not include RC

2.15.3.12 Routing Context

2.15.3.12.1 Description The Routing Context value used in M3UA ASPAC messages.



M3UA client Read Write

Integer

2.15.3.12.3 Values

Value Description

0x0 - 0xFFFFFFFD Valid Routing Context values.

0xFFFFFFFE/0xFFFFFFFF Reserved for internal use

2.15.3.13 Options

2.15.3.13.1 Description The different optional configuration allowed in AS resource.



M3UA client Read Write

Bitmask



2.15.3.13.3 Values

Value Description

None No additional options configured.

Single-DAUD This will make SVI send M3UA DAUD messages with only 1 affected destination pointcode inside it.

STP-Routing Forces the SVI to process M3UA messages instead of attempting routing at MTP-L3-Routing. This means that the Labels will be checked even if the SVI-SS connection is a client

SG-Routing Forces the SVI to process M3UA messages as an SG, even if as a client.

AS-Loadshare Traffic will be load-shared across this AS and its partner (subject to AS status and DP status)

AS-Primary Traffic will be sent on this AS in preference to its partner (subject to AS status and DP status)

AS-Secondary Traffic will be sent on this AS's partner in preference to this AS (subject to AS status and DP status)

Forward-DPC-Status Will forward the DPC status of a connection if the connection type is Client

SNMP-Trap Add snmp trap generation on resource state change.





All AS Read Integer





All AS Read Integer





All AS Read Integer





All AS Read Integer







All AS Read Integer





All AS Read Integer





All AS Read Integer





All AS Read Integer





All AS Read Integer





All AS Read Integer







All AS Read Integer


2.15.3.25.1 Description If the number of bytes per second threshold is exceeded then the AS will be throttled until the next

second. The AS link will queue the received AS messages



All AS Write Integer


2.15.3.26.1 Description If the number of messages per second threshold is exceeded then the AS will be throttled until the

next second. The AS link will queue the received AS messages





2.15.3.27.1 Description Number of AS messages to be queued after throttle before discard




2.15.3.28 SSME XML

2.15.3.28.1 Description XML Resource to be used for STP routing.



All AS Read Write No-Default

Resource



2.16 L3 Label / SCCP Label / TCAP Label

The L3, SCCP and TCAP resources have a similar structure.

‘Match’ Section – multiple parameters to form a match.

<param> Present

(Where <param> is the name of a protocol parameter, which may be present in a message)

Used to match against the presence (or absence) of a parameter in the received message

‘Present’ – must be Present to match

‘Absent’ – must be Absent to match

‘Ignore’ – presence or absence does not affect the match

<param>

(Where <param> is the name of a protocol parameter)

Use to match against the value of a parameter in the received message

<value> - received parameter must be this value

‘Ignore’ – value will not affect the match

‘Set_’ Section – multiple parameters to manipulate the message

‘Set <param> Present’ Attributes

(Where <param> is the name of a protocol parameter, which may be present in a message)

Used in the manipulation of messages.

‘Present’ – parameter will be included in outgoing message

‘Absent’ – parameter will not be included in the outgoing message

‘Leave’ – parameter will not be altered

‘Set <param>’

(Where <param> is the name of a protocol parameter)

<value> - if the parameter is either (a) already in the received message or (b) ‘Set <param>

Present’ is ‘Present’, the outgoing message will have this parameter, set to this value.

‘leave’ – if present, value will not be altered

Other Labels Section

‘More <X> Labels’ ... attribute

If set, when the routing process matches this label, the labels listed in this are also

searched for a match.

‘<X> Labels’ attribute

e.g. SCCP label, TCAP label – the next layer up of parameter matching

Routing

‘MTP Route’ attribute

2.16.1 L3 Label

2.16.1.1 Description

Resource used to define the Layer 3 label for best match routing/manipulation.

2.16.1.2 Products

SVI-STP



2.16.1.3 Attributes

2.16.1.3.1 Options

2.16.1.3.1.1 Definition



Bit Mask Flag

2.16.1.3.1.2 Values

Value Description


2.16.1.3.2 OPC

2.16.1.3.2.1 Description

Match either a defined value or any OPC which is present.



All Read Integer

2.16.1.3.2.3 Values

Value Description

Match to defined

Ignore Match any OPC present

2.16.1.3.3 DPC


Match either a defined value or any DPC which is present.



All Read Integer

2.16.1.3.3.3 Values

Value Description

Match to defined

Ignore Match any DPC present

2.16.1.3.4 SI


Match either a defined value or any SI which is present.



All Read Integer



2.16.1.3.4.3 Values

Value Description

Match to defined

Ignore Match any SI present

2.16.1.3.5 NI


Match either a defined value or any NI which is present.



All Read Integer

2.16.1.3.5.3 Values

Value Description

Match to defined

Ignore Match any NI present

2.16.1.3.6 M3UA_NA_Present


(M3UA messages only) Match only if the Network Appearance parameter is present in the message




Drop Down List

2.16.1.3.6.3 Values

Value Description

Present Network Appearance must be Present

Absent Network Appearance must be Absent

Ignore Network Appearance can be present or absent, but will not count towards a best match total.

2.16.1.3.7 M3UA_NA


(M3UA messages only) Match either a defined value or any Network Appearance which is present.



All Read Integer

2.16.1.3.7.3 Values

Value Description

Match to defined

Ignore Match any NA present

2.16.1.3.8 M3UA_RC_Present


(M3UA messages only) Match only if the Routing Context parameter is present in the message






Drop Down List

2.16.1.3.8.3 Values

Value Description

Present Routing Context must be Present

Absent Routing Context must be Absent

Ignore Routing Context can be present or absent, but will not count towards a best match total.

2.16.1.3.9 M3UA_RC


(M3UA messages only) Match either a defined value or any Routing Context which is present.



All Read Integer

2.16.1.3.9.3 Values

Value Description

Match to defined

Ignore Match any RC present

2.16.1.3.10 M3UA_CI_Present


(M3UA messages only) Match only if the Correlation Id parameter is present in the message




Drop Down List

2.16.1.3.10.3 Values

Value Description

Present Correlation Id must be Present

Absent Correlation Id must be Absent

Ignore Correlation Id can be present or absent, but will not count towards a best match total.

2.16.1.3.11 M3UA_CI


(M3UA messages only) Match either a defined value or any Correlation ID which is present.



All Read Integer



2.16.1.3.11.3 Values

Value Description

Match to defined

Ignore Match any CI present

2.16.1.3.12 Set OPC


Manipulate the OPC to the defined value or leave it in the current state.



All Write Integer

2.16.1.3.12.3 Values

Value Description

Manipulate OPC to value set

Ignore Do not manipulate

2.16.1.3.13 Set DPC


Manipulate the DPC to the defined value or leave it in the current state.



All Write Integer

2.16.1.3.13.3 Values

Value Description

Manipulate DPC to value set


2.16.1.3.14 Set SI


Manipulate the SI to the defined value or leave it in the current state.



All Write Integer

2.16.1.3.14.3 Values

Value Description

Manipulate SI to value set


2.16.1.3.15 Set NI


Manipulate the NI to the defined value or leave it in the current state.



All Write Integer



2.16.1.3.15.3 Values

Value Description

Manipulate SI to value set


2.16.1.3.16 Set_M3UA_NA_Present


(M3UA messages only) Controls the presence of the Network Appearance parameter in the outgoing

message




Drop Down List

2.16.1.3.16.3 Values

Value Description

Present Network Appearance will be Present in the outgoing message

Absent Network Appearance will not be in the outgoing message

Ignore The presence of Network Appearance in the outgoing message, will be the same as in the incoming message

2.16.1.3.17 Set_M3UA_NA


(M3UA messages only)

If Network Appearance is to be included in the outgoing message (set by M3UA_NA_Present), this

attribute sets the value.



All Read Integer

2.16.1.3.17.3 Values

Value Description

0-HFFFFFFFD Insert set value into the message

Leave Do not change value

2.16.1.3.18 Set_M3UA_RC_Present


(M3UA messages only) Controls the presence of the Routing Context parameter in the outgoing

message.




Drop Down List

2.16.1.3.18.3 Values

Value Description

Present Routing Context will be Present in the outgoing message

Absent Routing Context will not be in the outgoing message



Ignore The presence of Routing Context in the outgoing message, will be the same as in the incoming message

2.16.1.3.19 Set_M3UA_RC



If Routing Context is to be included in the outgoing message (set by M3UA_RC_Present), this

attribute sets the value.



All Read Integer

2.16.1.3.19.3 Values

Value Description



2.16.1.3.20 Set_M3UA_CI_Present


(M3UA messages only) Controls the presence of the Correlation ID parameter in the outgoing

message




Drop Down List

2.16.1.3.20.3 Values

Value Description

Present Correlation ID will be Present in the outgoing message

Absent Correlation ID will not be in the outgoing message

Ignore The presence of Correlation ID in the outgoing message, will be the same as in the incoming message

2.16.1.3.21 Set_M3UA_CI



If Correlation ID is to be included in the outgoing message (set by M3UA_CI_Present), this attribute

sets the value.



All Read Integer

2.16.1.3.21.3 Values

Value Description





2.16.1.3.22 More L3Labels


Add additional Layer 3 labels for best match routing/manipulation.




2.16.1.3.23 SCCPLabels


Add SCCP labels for best match routing/manipulation.




2.16.1.3.24 MTP Route


Adds an MTP Route.




2.16.1.3.25 Tx Msg Total


Statistic showing total number of Messages being sent matching this label.



All Read Integer

2.16.1.3.26 Tx Msg/Sec


Statistic showing real-time Messages/Second being sent matching this label.



All Read Integer

2.16.1.3.27 Tx Msg/Sec Max


Statistic showing maximum Messages/Second send rate since system start matching this label.



All Read Integer



2.16.1.3.28 Rx Msg Total


Statistic showing total number of Messages received since system start.



All Read Integer

2.16.1.3.29 Rx Msg/Sec


Statistic showing real-time Messages/Second being received matching this label.



All Read Integer

2.16.1.3.30 Rx Msg/Sec Max


Statistic showing maximum Messages/Second receive rate since system start matching this label.



All Read Integer

2.16.2 SCCP Label


Resource used to define the SCCP label for best match routing/manipulation.

2.16.2.2 Products

SVI-STP

2.16.2.3 Attributes

2.16.2.3.1 Options




Bit Mask Flag

2.16.2.3.1.2 Values

Value Description


2.16.2.3.2 CDPN_Present


Define whether the CDPN is expected to be present, not present or choose to ignore the state.






Integer

2.16.2.3.2.3 Values

Value Description

Present CDPN must be present

Absent CDPN must be absent

Ignore CDPN can be present or absent, but will not count towards a best match total.

2.16.2.3.3 CDPN_National


Define the value expected or ignore the value.




Integer

2.16.2.3.3.3 Values

Value Description

Ignore CDPN can be national or international, but will not count towards a best match total.

National CDPN is national

International CDPN is international

2.16.2.3.4 CDPN_RoutingInd






Integer

2.16.2.3.4.3 Values

Value Description

Route On GT CDPN should Route using the Global Title

Route On SSN CDPN should Route using the Sub System Number

Ignore CDPN can route using the Global Title or Sub System Number, but will not count towards a best match total.

2.16.2.3.5 CDPN_SSN_Present








Integer

2.16.2.3.5.3 Values

Value Description

Present CDPN SSN must be present

Absent CDPN SSN must be absent

Ignore CDPN SSN can be present or absent, but will not count towards a best match total.

2.16.2.3.6 CDPN_SSN


Define the SSN type.




Drop Down List

2.16.2.3.6.3 Values

Value Description

ISUP Sets the type matched to ISUP

OMAP Sets the type matched to OMAP

MAP Sets the type matched to MAP

HLR Sets the type matched to HLR

VLR Sets the type matched to VLR

MSC Sets the type matched to MSC

EIC Sets the type matched to EIC

AUC Sets the type matched to AUC

ISDN SS Sets the type matched to ISDN SS

B-ISDN Sets the type matched to B-ISDN

TCtest Sets the type matched to TCtest

Ignore/Leave CDPN SSN can be any type, but will not count towards a best match total.

2.16.2.3.7 CDPN_Pointcode_Present






Integer

2.16.2.3.7.3 Values

Value Description

Present CDPN Pointcode must be present



Absent CDPN Pointcode must be absent

Ignore CDPN Pointcode can be present or absent, but will not count towards a best match total.

2.16.2.3.8 CDPN_Pointcode






Integer

2.16.2.3.8.3 Values

Value Description

Define value to match

Ignore Any CDPN Pointcode will be matched, but will not count towards a best match total.

2.16.2.3.9 CDPN_GT_Present






Integer

2.16.2.3.9.3 Values

Value Description

Present CDPN GT must be present

Absent CDPN GT must be absent

Ignore CDPN GT can be present or absent, but will not count towards a best match total.

2.16.2.3.10 CDPN_NumberingPlan_Present






Integer

2.16.2.3.10.3 Values

Value Description

Present CDPN Numbering Plan must be present

Absent CDPN Numbering Plan must be absent



Ignore CDPN Numbering Plan can be present or absent, but will not count towards a best match total.

2.16.2.3.11 CDPN_NumberingPlan


Define the Numbering Plan type.




Drop Down List

2.16.2.3.11.3 Values

Value Description

Unknown Sets the type matched to Unknown

ISDN Sets the type matched to ISDN

Generic Sets the type matched to Generic

Data Sets the type matched to Data

Telex Sets the type matched to Telex

Maritime Mobile Sets the type matched to Maritime Mobile

Land Mobile Sets the type matched to Land Mobile

ISDN/mobile Sets the type matched to ISDN/mobile

Ignore/Leave CDPN Numbering Plan can be any type, but will not count towards a best match total.

2.16.2.3.12 CDPN_TranslationType_Present






Integer

2.16.2.3.12.3 Values

Value Description

Present CDPN Translation Type must be present

Absent CDPN Translation Type must be absent

Ignore CDPN Translation Type can be present or absent, but will not count towards a best match total.

2.16.2.3.13 CDPN_ TranslationType





All Read Write

Integer



No-Default

2.16.2.3.13.3 Values

Value Description


Ignore Any CDPN Translation Type will be matched, but will not count towards a best match total.

2.16.2.3.14 CDPN_ EncodingScheme_Present






Integer

2.16.2.3.14.3 Values

Value Description

Present CDPN Encoding Scheme must be present

Absent CDPN Encoding Scheme must be absent

Ignore CDPN Encoding Scheme can be present or absent, but will not count towards a best match total.

2.16.2.3.15 CDPN_ EncodingScheme


Define the Encoding Scheme type.




Drop Down List

2.16.2.3.15.3 Values

Value Description


BCD Sets the type matched to BCD

National Sets the type matched to National

Ignore/Leave CDPN Encoding Scheme can be any type, but will not count towards a best match total.

2.16.2.3.16 CDPN_ NOA_Present








Integer

2.16.2.3.16.3 Values

Value Description

Present CDPN NOA must be present

Absent CDPN NOA must be absent

Ignore CDPN NOA can be present or absent, but will not count towards a best match total.

2.16.2.3.17 CDPN_ NOA


Define the NOA type.




Drop Down List

2.16.2.3.17.3 Values

Value Description

Spare Sets the type matched to Spare

Subscriber Sets the type matched to Subscriber



International Sets the type matched to International

Network Specific Sets the type matched to Network Specific

UK Specific Sets the type matched to UK Specific

Ignore/Leave CDPN Encoding Scheme can be any type, but will not count towards a best match total.

2.16.2.3.18 CGPN_Present


Define whether the CGPN is expected to be present, not present or choose to ignore the state.




Integer

2.16.2.3.18.3 Values

Value Description

Present CGPN must be present

Absent CGPN must be absent

Ignore CGPN can be present or absent, but will not count towards a best match total.



2.16.2.3.19 CGPN _National






Integer

2.16.2.3.19.3 Values

Value Description

Ignore CGPN can be national or international, but will not count towards a best match total.

National CGPN is national

International CGPN is international

2.16.2.3.20 CGPN_RoutingInd






Integer

2.16.2.3.20.3 Values

Value Description

Route On GT CGPN should Route using the Global Title

Route On SSN CGPN should Route using the Sub System Number

Ignore CGPN can route using the Global Title or Sub System Number, but will not count towards a best match total.

2.16.2.3.21 CGPN_SSN_Present






Integer

2.16.2.3.21.3 Values

Value Description

Present CGPN SSN must be present

Absent CGPN SSN must be absent

Ignore CGPN SSN can be present or absent, but will not count towards a best match total.



2.16.2.3.22 CGPN_SSN


Define the SSN type.




Drop Down List

2.16.2.3.22.3 Values

Value Description

ISUP Sets the type matched to ISUP

OMAP Sets the type matched to OMAP

MAP Sets the type matched to MAP

HLR Sets the type matched to HLR

VLR Sets the type matched to VLR

MSC Sets the type matched to MSC

EIC Sets the type matched to EIC

AUC Sets the type matched to AUC

ISDN SS Sets the type matched to ISDN SS

B-ISDN Sets the type matched to B-ISDN

TCtest Sets the type matched to TCtest

Ignore/Leave CGPN SSN can be any type, but will not count towards a best match total.

2.16.2.3.23 CGPN_Pointcode_Present






Integer

2.16.2.3.23.3 Values

Value Description

Present CGPN Pointcode must be present

Absent CGPN Pointcode must be absent

Ignore CGPN Pointcode can be present or absent, but will not count towards a best match total.

2.16.2.3.24 CGPN_Pointcode








Integer

2.16.2.3.24.3 Values

Value Description


Ignore Any CGPN Pointcode will be matched, but will not count towards a best match total.

2.16.2.3.25 CGPN_GT_Present






Integer

2.16.2.3.25.3 Values

Value Description

Present CGPN GT must be present

Absent CGPN GT must be absent

Ignore CGPN GT can be present or absent, but will not count towards a best match total.

2.16.2.3.26 CGPN_NumberingPlan_Present






Integer

2.16.2.3.26.3 Values

Value Description

Present CGPN Numbering Plan must be present

Absent CGPN Numbering Plan must be absent

Ignore CGPN Numbering Plan can be present or absent, but will not count towards a best match total.

2.16.2.3.27 CGPN_NumberingPlan


Define the Numbering Plan type.






Drop Down List

2.16.2.3.27.3 Values

Value Description


ISDN Sets the type matched to ISDN

Generic Sets the type matched to Generic

Data Sets the type matched to Data

Telex Sets the type matched to Telex

Maritime Mobile Sets the type matched to Maritime Mobile

Land Mobile Sets the type matched to Land Mobile

ISDN/mobile Sets the type matched to ISDN/mobile

Ignore/Leave CGPN Numbering Plan can be any type, but will not count towards a best match total.

2.16.2.3.28 CGPN_TranslationType_Present






Integer

2.16.2.3.28.3 Values

Value Description

Present CGPN Translation Type must be present

Absent CGPN Translation Type must be absent

Ignore CGPN Translation Type can be present or absent, but will not count towards a best match total.

2.16.2.3.29 CGPN_ TranslationType






Integer

2.16.2.3.29.3 Values

Value Description


Ignore Any CGPN Translation Type will be matched, but will not count towards a best match total.



2.16.2.3.30 CGPN_ EncodingScheme_Present






Integer

2.16.2.3.30.3 Values

Value Description

Present CGPN Encoding Scheme must be present

Absent CGPN Encoding Scheme must be absent

Ignore CGPN Encoding Scheme can be present or absent, but will not count towards a best match total.

2.16.2.3.31 CGPN_ EncodingScheme


Define the Encoding Scheme type.




Drop Down List

2.16.2.3.31.3 Values

Value Description


BCD Sets the type matched to BCD


Ignore/Leave CGPN Encoding Scheme can be any type, but will not count towards a best match total.

2.16.2.3.32 CGPN_ NOA_Present






Integer

2.16.2.3.32.3 Values

Value Description

Present CGPN NOA must be present

Absent CGPN NOA must be absent

Ignore CGPN NOA can be present or absent, but will not count towards a best match total.



2.16.2.3.33 CGPN_ NOA


Define the NOA type.




Drop Down List

2.16.2.3.33.3 Values

Value Description

Spare Sets the type matched to Spare

Subscriber Sets the type matched to Subscriber



International Sets the type matched to International

Network Specific Sets the type matched to Network Specific

UK Specific Sets the type matched to UK Specific

Ignore/Leave CGPN Encoding Scheme can be any type, but will not count towards a best match total.

2.16.2.3.34 set Variant


Select the variant to be used for decoding.

This attribute is not used for matching and will be applied regardless.




Integer

2.16.2.3.34.3 Values

Value Description

ITU Sets the Variant to ITU

ANSI Sets the Variant to ANSI

Use L3 Variant Use the variant of the L3 transport that the message will be sent to

2.16.2.3.35 set_cdpn_Present


Set whether the CDPN is expected to be present, not present or choose not to manipulate the

current value.




Integer



2.16.2.3.35.3 Values

Value Description

Present Set CDPN present

Absent Set CDPN absent

Leave Do not manipulate value

2.16.2.3.36 set_cdpn_National


Set whether the CDPN is expected to be present, not present or choose not to manipulate the

current value.




Integer

2.16.2.3.36.3 Values

Value Description

National Set CDPN to National

International Set CDPN to International

Ignore/Leave Do not manipulate value

2.16.2.3.37 set_cdpn_RoutingInd


Set whether the CDPN Routing Ind is expected to Route on GT, Route on SSN or choose not to

manipulate the current value.




Integer

2.16.2.3.37.3 Values

Value Description

National Set CDPN to Route on GT

International Set CDPN to Route on SSN


2.16.2.3.38 set_cdpn_SSN_Present


Set whether the SSN is expected to be present, not present or choose not to manipulate the current

value.




Integer

2.16.2.3.38.3 Values



Value Description

Present Set SSN to present

Absent Set SSN to absent


2.16.2.3.39 set_cdpn_SSN


Set the SSN is type or choose not to manipulate the current value.




Drop Down List

2.16.2.3.39.3 Values

Value Description

ISUP Sets the type to ISUP

OMAP Sets the type to OMAP

MAP Sets the type to MAP

HLR Sets the type to HLR

VLR Sets the type to VLR

MSC Sets the type to MSC

EIC Sets the type to EIC

AUC Sets the type to AUC

ISDN SS Sets the type to ISDN SS

B-ISDN Sets the type to B-ISDN

TCtest Sets the type to TCtest

Ignore/Leave CDPN SSN can be any type, but will not count towards a best match total.

2.16.2.3.40 set_cdpn_Pointcode_Present


Set whether the CDPN Pointcode is expected to be present, not present or choose not to





Integer

2.16.2.3.40.3 Values

Value Description

Present Set CDPN Pointcode must be present

Absent Set CDPN Pointcode must be absent


2.16.2.3.41 set_cdpn_Pointcode

Set the CDPN Pointcode or choose not to manipulate the current value.






Integer

2.16.2.3.41.2 Values

Value Description

Set CDPN Pointcode value


2.16.2.3.42 set_cdpn_GT_Present


Set whether the CDPN Global Title is expected to be present, not present or choose not to





Integer

2.16.2.3.42.3 Values

Value Description

Present Set CDPN GT must be present

Absent Set CDPN GT must be absent


2.16.2.3.43 set_cdpn_NumberingPlan_Present


Set whether the CDPN Numbering Plan is expected to be present, not present or choose not to





Integer

2.16.2.3.43.3 Values

Value Description

Present Set CDPN Numbering Plan must be present

Absent Set CDPN Numbering Plan must be absent


2.16.2.3.44 set_cdpn_NumberingPlan


Set the Numbering Plan type or choose not to manipulate the current value.






Drop Down List

2.16.2.3.44.3 Values

Value Description

Unknown Sets the type to Unknown

ISDN Sets the type to ISDN

Generic Sets the type to Generic

Data Sets the type to Data

Telex Sets the type to Telex

Maritime Mobile Sets the type to Maritime Mobile

Land Mobile Sets the type to Land Mobile

ISDN/mobile Sets the type to ISDN/mobile


2.16.2.3.45 set_cdpn_TranslationType_Present







Integer

2.16.2.3.45.3 Values

Value Description

Present Set CDPN Translation Type must be present

Absent Set CDPN Translation Type must be absent


2.16.2.3.46 Set_cdpn_TranslationType


Define the value expected or choose not to manipulate the current value.




Integer

2.16.2.3.46.3 Values

Value Description

set Translation Type value




2.16.2.3.47 set_cdpn_EncodingScheme_Present







Integer

2.16.2.3.47.3 Values

Value Description

Present Set CDPN Encoding Scheme must be present

Absent Set CDPN Encoding Scheme must be absent


2.16.2.3.48 set_cdpn_ EncodingScheme


Set the Encoding Scheme type or choose not to manipulate the current value.




Drop Down List

2.16.2.3.48.3 Values

Value Description


BCD Sets the type to BCD

National Sets the type to National


2.16.2.3.49 set_cdpn_NOA_Present


Set whether the CDPN NOA is expected to be present, not present or choose not to manipulate the

current value.




Integer

2.16.2.3.49.3 Values

Value Description

Present Set CDPN NOA must be present



Absent Set CDPN NOA must be absent


2.16.2.3.50 set_cdpn_ NOA


Set the NOA type or choose not to manipulate the current value.




Drop Down List

2.16.2.3.50.3 Values

Value Description

Spare Sets the type to Spare

Subscriber Sets the type to Subscriber



International Sets the type to International

Network Specific Sets the type to Network Specific

UK Specific Sets the type to UK Specific


2.16.2.3.51 set_cdpn_strip


Set the number of characters to strip from the CDPN




Integer

2.16.2.3.52 set_cdpn_prefix


Set the characters to prefix the CDPN with




Integer

2.16.2.3.53 set_cgpn_Present


Set whether the CGPN is expected to be present, not present or choose not to manipulate the

current value.



All Read Integer



Write No-Default

2.16.2.3.53.3 Values

Value Description

Present Set CGPN must be present

Absent Set CGPN must be absent


2.16.2.3.54 set_cgpn_National


Set whether the CGPN is expected to be present, not present or choose not to manipulate the

current value.




Integer

2.16.2.3.54.3 Values

Value Description

National Set CGPN must be National

International Set CGPN must be International


2.16.2.3.55 set_cgpn_RoutingInd


Set whether the CGPN Routing Ind is expected to Route on GT, Route on SSN or choose not to





Integer

2.16.2.3.55.3 Values

Value Description

National Set CGPN to Route on GT

International Set CGPN to Route on SSN


2.16.2.3.56 set_cgpn_SSN_Present


Set whether the SSN is expected to be present, not present or choose not to manipulate the current

value.






Integer

2.16.2.3.56.3 Values

Value Description

Present Set SSN must be present

Absent Set SSN must be absent


2.16.2.3.57 set_cgpn_SSN


Set the SSN is type or choose not to manipulate the current value.




Drop Down List

2.16.2.3.57.3 Values

Value Description

ISUP Sets the type to ISUP

OMAP Sets the type to OMAP

MAP Sets the type to MAP

HLR Sets the type to HLR

VLR Sets the type to VLR

MSC Sets the type to MSC

EIC Sets the type to EIC

AUC Sets the type to AUC

ISDN SS Sets the type to ISDN SS

B-ISDN Sets the type to B-ISDN

TCtest Sets the type to TCtest

Ignore/Leave CGPN SSN can be any type, but will not count towards a best match total.

2.16.2.3.58 set_cgpn_Pointcode_Present


Set whether the CGPN Pointcode is expected to be present, not present or choose not to





Integer

2.16.2.3.58.3 Values

Value Description

Present Set CGPN Pointcode must be present

Absent Set CGPN Pointcode must be absent




2.16.2.3.59 set_cgpn_Pointcode

Set the CGPN Pointcode or choose not to manipulate the current value.




Integer

2.16.2.3.59.2 Values

Value Description

Set CGPN Pointcode value


2.16.2.3.60 set_cgpn_GT_Present


Set whether the CGPN Global Title is expected to be present, not present or choose not to





Integer

2.16.2.3.60.3 Values

Value Description

Present Set CGPN GT must be present

Absent Set CGPN GT must be absent


2.16.2.3.61 set_cgpn_NumberingPlan_Present


Set whether the CGPN Numbering Plan is expected to be present, not present or choose not to





Integer

2.16.2.3.61.3 Values

Value Description

Present Set CGPN Numbering Plan must be present

Absent Set CGPN Numbering Plan must be absent




2.16.2.3.62 set_cgpn_NumberingPlan


Set the Numbering Plan type or choose not to manipulate the current value.




Drop Down List

2.16.2.3.62.3 Values

Value Description


ISDN Sets the type to ISDN

Generic Sets the type to Generic

Data Sets the type to Data

Telex Sets the type to Telex

Maritime Mobile Sets the type to Maritime Mobile

Land Mobile Sets the type to Land Mobile

ISDN/mobile Sets the type to ISDN/mobile


2.16.2.3.63 set_cgpn_TranslationType_Present







Integer

2.16.2.3.63.3 Values

Value Description

Present Set CGPN Translation Type must be present

Absent Set CGPN Translation Type must be absent


2.16.2.3.64 Set_cgpn_TranslationType


Define the value expected or choose not to manipulate the current value.




Integer



2.16.2.3.64.3 Values

Value Description

set Translation Type value


2.16.2.3.65 set_cgpn_EncodingScheme_Present







Integer

2.16.2.3.65.3 Values

Value Description

Present Set CGPN Encoding Scheme must be present

Absent Set CGPN Encoding Scheme must be absent


2.16.2.3.66 CGPN_ EncodingScheme


Set the Encoding Scheme type or choose not to manipulate the current value.




Drop Down List

2.16.2.3.66.3 Values

Value Description


BCD Sets the type to BCD



2.16.2.3.67 set_cgpn_NOA_Present


Set whether the CGPN NOA is expected to be present, not present or choose not to manipulate the

current value.




Integer



2.16.2.3.67.3 Values

Value Description

Present Set CGPN NOA must be present

Absent Set CGPN NOA must be absent


2.16.2.3.68 set_cgpn_ NOA


Set the NOA type or choose not to manipulate the current value.




Drop Down List

2.16.2.3.68.3 Values

Value Description

Spare Sets the type to Spare

Subscriber Sets the type to Subscriber



International Sets the type to International

Network Specific Sets the type to Network Specific

UK Specific Sets the type to UK Specific


2.16.2.3.69 set_cgpn_strip


Set the number of characters to strip from the CGPN




Integer

2.16.2.3.70 set_cgpn_prefix


Set the characters to prefix the CGPN with




Integer

2.16.2.3.71 More SCCPLabels


Add additional SCCP labels for best match routing/manipulation.






2.16.2.3.72 TCAPLabels


Add TCAP labels for best match routing/manipulation.




2.16.2.3.73 MTP Route


Add an MTP Route.




2.16.2.3.74 SSME Manipulation


Check the SSME engine for any Map Manipulation required for the SCCP label. The Endpoint is

created from the SCCP Calling and Called Address




Flag

2.16.2.3.74.3 Values

Value Description

On Check the SSME engine to perform MAP manipulation

Off No Manipulation required

2.16.2.3.75 Tx Msg/Sec





All Read Integer






All Read Integer








All Read Integer

2.16.2.3.78 Rx Msg/Sec





All Read Integer






All Read Integer

2.16.3 TCAP Label


Resource used to define the TCAP label for best match routing/manipulation.

2.16.3.2 Products

SVI-STP

2.16.3.3 Attributes

2.16.3.3.1 Options




Bit Mask Flag

2.16.3.3.1.2 Values

Value Description


2.16.3.3.2 Protocol








Integer

2.16.3.3.2.3 Values

Value Description

ITU CGPN Translation Type must be ITU

ANSI CGPN Translation Type must be ANSI

Ignore CGPN Translation Type can be ITU or ANSI, but will not count towards a best match total.

2.16.3.3.3 Primitive


Define the Primitive type.




Drop Down List

2.16.3.3.3.3 Values

Value Description

BEGIN Sets the type matched to BEGIN

END Sets the type matched to END

CONTINUE Sets the type matched to CONTINUE

UNI-DIRECTIONAL Sets the type matched to UNI-DIRECTIONAL

ABORT Sets the type matched to ABORT

Ignore Primitive can be any type, but will not count towards a best match total.

2.16.3.3.4 Component


Define the Component type.




Drop Down List

2.16.3.3.4.3 Values

Value Description

ITU Invoke Sets the type matched to ITU Invoke

ITU Return Result Sets the type matched to ITU Return Result

ITU Return Error Sets the type matched to ITU Return Error

ITU Reject Sets the type matched to ITU Reject

ITU Return Result NL Sets the type matched to ITU Return Result NL

ANSI Invoke Sets the type matched to ANSI Invoke

ANSI Return Result Sets the type matched to ANSI Return Result

ANSI Return Error Sets the type matched to ANSI Return Error



ANSI Reject Sets the type matched to ANSI Reject

Ignore Component can be any type, but will not count towards a best match total.

2.16.3.3.5 MAP_Operation_Code


Define the MAP Operation Code type.




Drop Down List

2.16.3.3.5.3 Values

Value Description

Insert Subscriber Data Sets the type matched to Insert Subscriber Data

Send Routing Info For SM Sets the type matched to Send Routing Info For SM

MP Forward Short Message Sets the type matched to MP Forward Short Message

Update Location Sets the type matched to Update Location

Cancel Location Sets the type matched to Cancel Location

Send IMSI Sets the type matched to Send IMSI

Send Routing Info Sets the type matched to Send Routing Info

Unstructured SS Notify Sets the type matched to Unstructured SS Notify

Inform Service Centre Sets the type matched to Inform Service Centre

Alert Service Centre Sets the type matched to Alert Service Centre

Alert Service Centre Without Result

Sets the type matched to Alert Service Centre Without Result

MT Forward Short Message Sets the type matched to MT Forward Short Message

MT AS MO Forward Short Message

Sets the type matched to MT AS MO Forward Short Message

Report SM Delivery Status Sets the type matched to Report SM Delivery Status

Set Message Waiting Data Sets the type matched to Set Message Waiting Data

Any Time Interrogation Sets the type matched to Any Time Interrogation

Ready For SM Sets the type matched to Ready For SM

Provide Subscriber Info Sets the type matched to Provide Subscriber Info

Ignore Component can be any type, but will not count towards a best match total.

2.16.3.3.6 More TCAPLabels


Add additional TCAP labels for best match routing/manipulation.




2.16.3.3.7 Tx Msg/Sec





All Read Integer








All Read Integer






All Read Integer

2.16.3.3.10 Rx Msg/Sec





All Read Integer






All Read Integer

2.17 MTP CDR

2.17.1 Description

The MTP CDR Resource is used to configure the collection of SS7 MTPL3 CDR records. This resource

can be set against a SS7 Linkset resource, and controls the way that the SVI writes to the MTP CDR

text file.

The overall configuration of MTP CDRs is explained in SalesForce solution 529.

2.17.2 Products

SVI-MG | SVI-MGC | SVI-STP | SVI-SMSC | SVI-SG



2.17.3 Attributes

2.17.3.1 Status

2.17.3.1.1 Description Must be set to INS to function



All Read Write

List

2.17.3.1.3 Values

Value Description

INS

2.17.3.2 Options


Controls various behaviours



All Read Write

List

2.17.3.2.3 Values

Value Description

Daily creates a new MTPCDR file every day (default is hourly)

Terminated RX/TX messages will be displayed differently in the CDR log. This should normally be enabled.

Threaded creates a separate thread for the MTP CDR logger

2.17.3.3 Sleep


Controls how long a threaded MTP CDR task sleeps between activity



All Read Write

Integer

2.17.3.3.3 Values

Value Description

Any (ms) Value in milliseconds

2.17.3.4 Filesize


Maximum size of a CDR file before it is closed and a new one created - old file will be given

extension .hh.mm.ssss when new one is created



All Read Write

Integer



2.17.3.4.3 Values

Value Description

Any Value in bytes

2.17.3.5 Location


Folder location where MTP CDRs will be located. Should be terminated with \



All Read Write

String

2.17.3.5.3 Values

Value Description

Any Location (normally relative to /home/squire/)

2.17.3.6 MTP Filter


The MTP Route resource used to filter which MTPL3 messages should be logged to the CDR file.

The MTP Route attributes linkset, OPC, DPC, SIO and NI can be used to filter messages.



All Read Write

Resource

2.17.3.6.3 Values

Value Description

2.18 XML

2.18.1 Description

The XML Resource is used to configure the SSME for the SVI-STP, or the SSME for the SVI-SS

2.18.2 Products

SVI-STP

2.18.3 Attributes

2.18.3.1 Status

2.18.3.1.1 Description Must be set to Start to function



All Read Write

List

2.18.3.1.3 Values



Value Description

INS

Start

2.18.3.2 Type


Controls the type of the XML



All Read Write

List

2.18.3.2.3 Values

Value Description

XML XML file to be used for the setup

2.18.3.3 File Type


The type of file to be used, to setup the relevant SSME



All Read Write

Integer

2.18.3.3.3 Values

Value Description

STP_SSME_XML_FILE STP SSME to be setup

VLD_SSME_XML_FILE Voice Destination SSME to be setup

2.18.3.4 Validation Type


The type of validation to be performed on the XML File



All Read Write

Integer

2.18.3.4.3 Values

Value Description

VLD_XSD_SCHEMA XML file to be validated against the XSD Schema defined

2.18.3.5 Filename


Location of XML File to be loaded



All Read Write

String

2.18.3.5.3 Values



Value Description

Any Location (normally relative to /home/squire/)

2.18.3.6 Validation file


The location of the XSD Schema



All Read Write

Resource

2.18.3.6.3 Values

Value Description

Any Location of the XSD Schema relative to /home/squire Default if not set /home/squire/ssme/.schema

2.18.3.7 ssmeoptions


Options to be used against the ssme xml resource

Controls various behaviours



All Read Write

Resource

2.18.3.7.3 Values

Value Description

Validate On loading the XML file validate against the XSD Schema

New Output File Creates a new output file containing the results of testing and parsing

Run Tests Run tests on loading the XML file

Check Resource Names Confirms that the resource names in the XML file exist within the SVI-SS

2.18.3.8 ssmedebug


Sets the SSME Debug level (XML task must be enabled)



All Read Write

Resource

2.18.3.8.3 Values

Value Description

All All debug turned on

Critical Only critical debug is displayed

Eng Only engineering debug is displayed

Err Only Err debug is displayed

Info Only Info debug is displayed

Log Only log debug is displayed



2.18.3.9 Ssme threshold


Sets the SSME threshold for look-ups in the SSME, if exceeded then the Input and Path is displayed

in the log file.



All Read Write

Resource

2.18.3.9.3 Values

Value Description

Any Integer set in micro seconds

2.18.3.10 Max Time


Shows the Maximum time of a call to the SSME. Set as micro sets



All Read

Resource

2.18.3.10.3 Values

Value Description


2.18.3.11 Show SSME Longest


Only available via the telnet, shows the 10 longest ssme lookups in the system. Display input and

SSME path



All Read

Resource

2.18.3.11.3 Values

Value Description


Documents

SS7 Glossary - Squire Technologies · SS7 Glossary Squire Technologies – Confidential Document S:\Support\User Guides\Product\Other Guides\Resource Glossarys\Drafts \Appendix-C-SS7-SVI-Resource-Glossary