SPRAYER PARTS CATALOGUE PUMPS AND COUPLERSwestwardparts.com/public/downloads/catalogue/sprayer-parts/1... · 1-4 PUMPS AND COUPLERS SPRAYER PARTS CATALOGUE©2003 Delavan 4 Roller

PUMPS AND COUPLERSSPRAYER PARTS CATALOGUE©2003

ACCESSORIESShurFlo ........................................................... 1-78 to 1-80

CENTRIFUGAL PUMPSAce (parts only) (GE 100) ................................ 1-22Banjo.............................................................. 1-20, 1-21

CENTRIFUGAL ELECTRIC MOTOR DRIVEN PUMPSAce ................................................................ 1-37 to 1-40Banjo.............................................................. 1-20, 1-21Hypro ............................................................. 1-47, 1-48

CENTRIFUGAL FRAME MOUNT PUMPAce ................................................................ 1-37 to 1-42Hypro ............................................................. 1-47, 1-48

CENTRIFUGAL GAS ENGINE DRIVEN PUMPSAce ................................................................ 1-37 to 1-42Ace (parts only) (GE100) ................................. 1-22Banjo.............................................................. 1-20, 1-21Hypro ............................................................. 1-47, 1-48Westward(Water Transfer) .............................. 1-94

CENTRIFUGAL HYDRAULIC DRIVEN PUMPSAce ................................................................ 1-29 to 1-36Delavan .......................................................... 1-43Hypro ............................................................. 1-44 to 1-46

CENTRIFUGAL MAGNET CLUTCH PUMPSAce ................................................................ 1-41, 1-42Hypro ............................................................. 1-47, 1-48

CENTRIFUGAL PEDESTAL MOUNT PUMPSAce ................................................................ 1-37 to 1-42Banjo.............................................................. 1-20, 1-21Hypro ............................................................. 1-47, 1-48

CENTRIFUGAL PTO DRIVEN PUMPSAce ................................................................ 1-25 to 1-28Hypro ............................................................. 1-49, 1-50

COUPLERSPump Couplers ............................................... 1-96 to 1-99Quick Couplers ............................................... 1-96 to 1-99Shaft Couplings .............................................. 1-98

DIAPHRAGM 12 VOLT PUMPSFlojet .............................................................. 1-67 to 1-71ShurFlo ........................................................... 1-72 to 1-82ShurFlo Parts .................................................. 1-81, 1-82

DIAPHRAGM 110 VOLT PUMPSShurFlo ............................................................. 1-75, 1-76

DIAPHRAGM AIR DRIVEN PUMPSShurFlo ............................................................. 1-76FloJet ............................................................... 1-69

DIAPHRAGM PTO DRIVEN PUMPSHypro ............................................................... 1-52 to 1-66

ELECTRIC DRILL PUMPSShurFlo ............................................................. 1-79

FLOW LIMITER VALVE........................................................................ 1-36

FOOT VALVES & STRAINERS........................................................................ 1-95

HYDRAULIC FLOW LIMITER VALVE........................................................................ 1-36

IMPELLER PUMPSShurFlo ............................................................. 1-78, 1-79

OIL CHANGE SYSTEM 12 VOLTShurFlo ............................................................. 1-79

PISTON PUMPSHypro ............................................................... 1-17 to 1-19

PRESSURE WASHER PUMPSAccessories (General, Inter) ............................... 1-88Accessories (Westward) .................................... 1-93Comet Pump .................................................... 1-92, 1-93General Pump................................................... 1-88 to 1-91Inter Pump ....................................................... 1-88 to 1-91Westward ......................................................... 1-94

PROPORTIONATING PUMPSShurFlo ............................................................. 1-74

PUMPSPump Drive Specifications ................................. 1-2Pumps Roller Delavan ....................................... 1-3 to 1-8Pumps Roller Hypro .......................................... 1-9 to 1-16Pumps Piston Hypro ......................................... 1-17 to 1-19Pumps Centrifugal Banjo .................................. 1-20, 1-21Pumps Roller Ace .............................................. 1-23, 1-24Pumps Centrifugal Westward (Water Transfer) .. 1-94Pumps Centrifugal Ace ..................................... 1-25 to 1-42

I N D E X

PUMPS AND COUPLERSSPRAYER PARTS CATALOGUE©2003

I N D E X

PUMPS (CONTINUED)Pumps Centrifugal Delavan ............................... 1-43Pumps Centrifugal Hypro .................................. 1-44 to 1-50Pumps Turbine Delavan .................................... 1-51Pumps Diaphragm Hypro .................................. 1-52 to 1-66Pumps Diaphragm 12 Volt FloJet ...................... 1-67 to 1-71Pumps Diaphragm 12 Volt ShurFlo .................... 1-72 to 1-82Pumps Diaphragm Air Operated ....................... 1-69, 1-76Pumps Sump and Sewage ................................. 1-83 to 1-87Pumps High Pressure ........................................ 1-88 to 1-93Pumps Pressure Washer General and Inter ........ 1-88 to 1-91Pumps Pressure Washer Comet ......................... 1-92, 1-93

ROLLER PUMPSAce .................................................................. 1-23, 1-24Delavan ............................................................ 1-3 to 1-8

Hypro ............................................................... 1-9 to 1-16

ROLLER PUMPS 12 VOLTDelavan ............................................................ 1-71

SUBMERSIBLE PUMP 24 VOLTShurFlo ............................................................. 1-78

SUMP & SEWAGE PUMPSMonarch .......................................................... 1-83 to 1-87

TURBINE PUMPSDelavan ............................................................ 1-51

1-1PUMPS AND COUPLERSSPRAYER PARTS CATALOGUE©2003

Sprayer Parts©2003 04/03

1-2 PUMPS AND COUPLERSSPRAYER PARTS CATALOGUE©2003

Pump Drives

How a pump is to be driven is often a primaryconsideration in selecting the proper type ofpump. If the power source has already beendetermined, the following chart can be offurther help in selecting the type of pump thatis best suited to your needs.

PUMP SHAFT ROTATIONWith many pumps, you need to specify whichdirection the shaft rotates …either clockwise(CW) or counter clockwise (CCW). Rules onshaft rotation are as follows:

RULE #1 “Eyes on the end”Always view the rotation when you’re facingthe end of the drive shaft. If it turns clockwise,it’s a clockwise shaft. Always use this rule fordetermining rotation of the pump shaft and forthe power source shaft (PTO, for example).Once you’ve determined the rotation of thepower source shaft, remember rule #2:

RULE #2 “Opposites attract”A clockwise (CW) rotating PTO shaft willrequire a counterclockwise (CCW) rotatingpump shaft, and vice versa. All shaft rotationreferences in this catalog are based on thesetwo rules.

PTO direct-mount (Torque Bar & Chain)Location of PTO driven pumps and pump driveunits can have a significant effect on pumplife. Mounting the pump directly to the PTO isalways a good choice. Even though installationis relatively easy, use caution to insure theshaft does not get bent or damaged. Alwaysuse a quality, properly secured coupler andprovide adequate support for the pump itselfin order to withstand the extreme bouncingand vibration the system must endure. PTOmounting shields should always be used formaximum safety and protection.

If your power source is: Roller Centrifugal Turbine Diaphragm Piston

540 rpm PTO direct coupledthrough gear drive:through belt/pully:

1000 rpm PTO direct coupledthrough gear drive:through belt/pulley:

Hydraulic Motor

12 Volt DC Motor

Gas Motor direct coupledthrough gear reduct:through belt/pulley:

Electric Motor direct coupledthrough belt/pulley:

You can use these pump types:

Part No. Description

70884 Torque Bar & Chain75179 PTO Clip Mounting


Lasts up to ten times longer than cast iron pumps.Features:♦ Special alloy body and end plate♦ Stainless steel rotor, bearings and shaft♦ Glass-filled polypropylene rollers♦ Viton seals (standard)

♦ Available in reverse rotation

Stronger Than Steel, Tougher Than Roundup®

D i a m o n d S e r i e s ™ R o l l e r P u m p s

JOIN DELAVAN’S CAST IRON AND NI-RESISTPUMP FAMILY TO GIVE YOU LONGERPUMP LIFE WITH HARSH CHEMCIALS.

The following test was conducted on a conventional CastIron 8 roller pump, and an 8 roller Diamond Series™ pumpusing a rate of two times the recommended rate ofRoundup® mixed with water.The pumps were running side by side at 1000 RPM’s and 40PSI, and pumping from the same tank mixture.The pumps ran 4 hours and then soaked in the solution for24 hours. They then ran continuous with the flow beingchecked every 24 hours, until the Cast Iron pump lost 50%of it’s flow. The Diamond Series™ pump lasted 10 timeslonger and was still in like new condition!WARNING: DO NOT RUN PUMP DRY.

FLUSH WITH ANTIFREEZE AFTER USE.

Pump comparison after a usage rate of 1000RPM’s at 40 PSI with a Roundup®/watermixture twice the recommended rate.

THE BEST CHEMICALRESISTANT PUMP THAT

MONEY CAN BUY!

Diamond Series Cast Iron


D e l a v a n 4 R o l l e r P u m p

SPECIFICATIONS♦ For direct electric motor drive or belt and pulley drive at a speed of 1800 rpm, delivers up to6.5 gpm. Minimum size electric motor: 1 ¼ horsepower.♦ For direct gas engine drive at speeds up to 2600 rpm, delivers up to 9.2 gpm.♦ Pressure to 150 psi, 1000 kPa♦ Speeds of 1800/2600 rpm♦ Capacity to 9.2 gpm at 2600 rpm♦ ¾” ports♦ Max. Recommended Pressure: 150 psi (1000 kPa)♦ Max. Recommended Temperature: 120°F (50° C)♦ Max. Recommended Motor Speed: 2600 rpm

PART NO. REPLACES REPLACES OLD DESCRIPTION

70000 4400C X44-5111 4 roller side port pump

70003 4400N X44-6111 Ni-resist pump70005 4400D X44-7111 Diamond Series Pump70260 4401C-M12 50098-1 12 volt 4 roller pump

REF. PART NO. REPLACES DESCRIPTION QTY. REQ.

1 70803 15070 Snap ring 2

2 70804 48237 Nameplate 1

3 70805 48236 Cap screw 4

4 70802 31350-142 Seal ring, Buna-N 1

5 70800 48234 Roller, Polypropylene, ½” 4

6 70806 31661-14 5/8” stainless steel shaft/cast iron rotor 1

7 70807 48231 End plate, cast iron 1

8 70808 15072 Ball bearing 2

9 70801 20468 Lip seal, Viton (Fluorocarbon compound) 2

10 70809 48229 Pump body, cast iron 1

REPAIR KIT FOR 4 ROLLER PUMP PART NO. REPLACES DESCRIPTION

70600 48631-1 4 roller pump repair kit 44-4000RK

PART NO. REPLACES DESCRIPTION QTY/KIT

70800 48234 Roller, Polypropylene, ½” dia. 4

70801 20468 Lip Seal, Fluorocarbon (Viton) 2

70802 31350-142 Seal Ring 1

FLOW RATES AND HORSEPOWER REQUIREMENTS FOR4 ROLLER PUMP PRESSURE 1800 RPM 2200 RPM 2600 RPM

GPM HP GPM HP GPM HP

0 psi 6.5 .12 7.7 .15 9.2 .19

25 psi 5.4 .24 6.7 .31 8.4 .3650 psi 4.7 .35 5.9 .42 7.7 .5475 psi 4.0 .43 5.3 .54 7.1 .70100 psi 3.5 .50 4.8 .65 6.7 .84125 psi 3.0 .55 4.3 .75 6.3 1.02150 psi 2.6 .60 3.9 .85 5.9 1.17

FLOW RATES AND HORSEPOWER REQUIREMENTS FOR4 ROLLER PUMP PRESSURE 1800 RPM 2200 RPM 2600 RPM

L/MIN KW L/MIN KW L/MIN KW

0 kPa 24.5 .09 19.5 .11 35.0 .14

100 kPa 22.0 .14 27.0 .18 32.8 .22200 kPa 20.0 .19 24.5 .24 31.2 .29300 kPa 18.0 .24 23.1 .29 29.2 .37500 kPa 15.5 .31 20.5 .39 27.5 .51600 kPa 14.3 .34 19.2 .44 26.5 .57700 kPa 13.3 .37 18.0 .49 25.5 .64

5/8” Dia. ShaftShaft Couplings(Series 2738)See Page 96-99 1

8

9

7

4

6

5

10

9

8

3

2

1

REPLACEMENT PARTS FOR 4 ROLLER PUMP

Note: Horsepowerlisted is for electricmotor drives. For gasengine drives, followgas enginemanufacturer’srecommendations. (Asan estimate for gasengines, double thehorsepowerrequirements forelectric motors listed).





70008 5500N X55-6110 Ni-resist pump70009 5500D X55-7110 Diamond Series Pump70884 33680 Torque Arm & Chain

SPECIFICATIONS♦ For 540 and 1000 rpm PTO driven applications.♦ Delivers up to 45 gpm at 1000 rpm and 0 psi.FEATURES♦ Body & endplate - cast iron.♦ Ball bearings - heavy-duty shielded bearings supportshaft at both ends. These sealed bearings arelubricated at the factory for the life of the pump.♦ Shaft 15/16” dia., 416 stainless steel♦ Rotor - cast iron♦ Rollers - 1” polypropylene♦ Seals - cartridge type, Viton lip seals♦ Seal ring - Buna-N♦ Ports - 1” NPT female side ports♦ Rotation - normal PTO rotation - counter-clockwiserotation when facing the shaft end


1 70813 15334 Snap ring 2

2 70814 48255 Nameplate 1

3 70815 15341 Cap screw 4

4 70812 48252 Seal ring, Buna-N 1

5 70810 48253 Roller, Polypropylene, 1” 5

6 70816 31661-15 15/16” stainless steel shaft/cast iron rotor 1

7 70817 48248-1 End plate, cast iron 1

8 71032 16228 Ball bearing 2

9 70861 47927 Lip seal, Viton (Fluorocarbon compound) 2

10 70819 48246-1 Pump body, cast iron 1





70810 48253 Roller, Polypropylene, 1” dia. 5

70861 47927 Lip Seal, Viton 2

70812 48252 Seal Ring 1

70885 22059 Old Style Roller ¾”

FLOW RATES AND KILOWATT REQUIREMENTS FOR 5 ROLLER PUMP PRESSURE 0 KPA 200 KPA 500 KPA 700 KPA 1000 KPA

RPM L/MIN KW L/MIN KW L/MIN KW L/MIN KW L/MIN KW

450* 79 .13 70 .47 60 .99 58 1.31 48 1.68

540* 95 .20 83 .58 75 1.15 70 1.53 64 1.99650* 105 .29 105 .75 95 1.40 90 1.82 85 2.48750* 126 .37 122 .88 110 1.61 105 2.07 95 2.89850* 151 .59 141 1.08 125 1.80 118 2.27 114 3.311000** 173 1.27 168 1.80 155 2.58 148 3.09 136 3.94

CouplersSee Page 96-99

FLOW RATES AND HORSEPOWER REQUIREMENTS FOR5 ROLLER PUMP PRESSURE 0 PSI 50 PSI 100 PSI 150 PSI 200 PSI

RPM GPM HP GPM HP GPM HP GPM HP GPM HP

450* 20.8 .18 16.4 .98 14.4 1.74 11.4 2.31 7.5 2.71

540* 25.1 .27 20.5 1.16 17.8 2.03 15.4 2.74 12.2 3.44650* 30.4 .39 25.7 1.45 22.6 2.41 20.3 3.42 17.3 4.26750* 34.7 .49 30.7 1.68 26.6 2.73 24.4 4.00 22.0 5.11850* 39.7 .79 35.1 1.93 31.0 3.00 28.1 4.60 26.2 5.951000** 46.5 1.62 42.5 2.93 38.5 4.11 35.1 5.42 - -

Note: To achieve rated capacity 2.5 cm suction and pressure hose should be used.

Note: To achieve rated capacity 1” suction and pressure hose should be used.

*For PTO Speeds below850 RPM:Pressures to 200 psi (1400 kPa)are recommended.**For PTO Speeds over 850 RPM:Max. Recommended Pressure:-for continuous duty is 100 psi(700 kPa)-for intermittent duty is 150 psi(1050 kPa)Max. Recommended temp120° F (50° C)Max. Recommended PTOspeed: 1000 rpm



70002 6600C-R XX6-5111 6 roller side port- reverse rotation pump

70004 6601C X66-5110 6 roller back port pump70011 6600N XX6-6110 6 roller side port Ni-resist pump70012 6600D XX6-7110 6 roller side port Diamond Series pump70020 6600C XX6-5110 6 roller side port pump70884 33680 Torque Arm & Chain

SPECIFICATIONS♦ For 540 and 1000 rpm PTO driven applications.♦ Delivers up to 19.5 gpm♦ Pressures to 300 psi

FEATURES♦ Body & endplate - cast iron.♦ Ball bearings - heavy-duty shieldedbearings support shaft at both ends. Thesesealed bearings are lubricated at the factoryfor the life of the pump.


1 70803 15070 Snap ring 2

2 70887 46210 Nameplate 1

3 70822 15077 Cap screw 4

4 70821 24819 Seal ring 1

5 70820 19341 Roller, Polypropylene, 11/16” 6

6 70823 31661-8 Stainless steel shaft/powdered metal rotor 1

7 70824 31664-1 End plate, cast iron 1

8 70808 15072 Ball bearing 2

9 70801 20468 Lip seal, Viton 2

10 70825 24817 Pump body Cast Iron 1





70613 18756 6 roller pump repair kit old style 11/16” rollers

70615 25227 6 roller pump repair kit old style ¾” rollers


70820 19341 Roller, Polypropylene, 11/16” 6

70801 20468 Shaft Seal, Viton A 2

70821 24819 Seal Ring 1

70885 22059 Old Style ¾” Roller

ROLLER PUMP CAPACITIES AND INPUT POWER (BASED ON WATER)SPEED 0 KPA 200 KPA 500 KPA 700 KPA 1000KPA 1500 KPA 2000 KPA

MODEL (RPM) L/MIN KW L/MIN KW L/MIN KW L/MIN KW L/MIN KW L/MIN KW L/MIN KW

6 roller 450 34.0 .09 29.5 .22 22.5 .52 18.5 .71 14.7 .98 8.0 1.4 3.0 1.9

17.5 mm 540 40.9 .11 35.6 .29 29.1 .59 26.1 .80 22.0 1.21 15.9 1.8 10.2 2.3650 48.0 .13 44.5 .34 38.0 .76 34.5 1.0 30.0 1.4 23.0 2.0 17.5 2.6750 55.5 .16 52.0 .40 45.0 .86 42.0 1.2 37.5 1.7 31.5 2.3 25.5 3.0850 62.5 .19 58.0 .46 57.0 1.0 50.0 1.4 45.5 1.9 39.0 2.6 33.0 3.41000 73.8 .22 70.0 .66 64.7 1.2 61.7 1.5 57.2 2.0 50.7 3.1 44.3 3.8

ROLLER PUMP CAPACITIES AND INPUT POWER (BASED ON WATER)SPEED 0 PSI 25 PSI 50 PSI 100 PSI 200 PSI 250 PSI 300 PSI

MODEL (RPM) GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP

6 roller 11/16” 450 9.1 .12 7.8 .27 6.5 .50 5.0 .95 2.6 1.8 1.6 2.2 .7 2.6

540 10.8 .15 9.6 .35 8.5 .60 6.9 1.1 4.6 2.2 3.4 2.7 2.4 3.3650 12.7 .17 11.6 .40 10.6 .73 9.1 1.3 6.7 2.5 5.5 3.1 4.5 3.7750 14.6 .20 13.7 .47 11.2 .86 11.2 1.6 8.6 2.9 7.6 3.5 6.5 4.2850 16.5 .25 15.5 .55 14.7 1.0 13.2 1.8 10.6 3.3 9.5 4.0 8.4 4.81000 19.5 .30 18.6 .80 17.8 1.2 16.3 2.0 13.8 3.7 12.6 4.6 11.5 5.5

♦ Shaft 5/8” dia., 416 stainless steel♦ Rotor - cast iron♦ Rollers - 11/16” polypropylene♦ Seals - cartridge type, Viton lip seals♦ Seal ring - Buna-N♦ ¾” ports♦ Max. Recommended Pressure: 300 psi(2000 kPa)♦ Max. Recommended Temperature: 120°F (50° C)♦ Max. Recommended Motor Speed:1000 rpm


12

8 9

10

6 5

4

18

97

3





70007 7000C-R X77-5111 7 roller side port - reverse rotation pump70010 7000N X77-6110 7 roller side port with Ni-resist housing & rotor70015 7000D X77-7110 7 roller side port Diamond series pump70884 33680 Torque Arm & Chain

SPECIFICATIONS♦ For 540 and 1000 rpm PTO driven applications.♦ Delivers up to 22.5 gpm♦ Pressures to 200 psi♦ 15/16” shaft♦ 3/4” ports♦ Max. Recommended Pressure: 300 psi (2000 kPa)♦ Max. Recommended Temperature: 120°F (50° C)♦ Max. Recommended Motor Speed: 850 rpm


1 70813 15334 Snap ring 2

2 70828 46209 Nameplate 1

3 70815 15341 Cap screw 4

4 70827 24829 Seal ring 1



7 70831 31666-1 End plate, cast iron (77-51_) 1

7 70832 31666-2 End plate, Ni-resist (77-61_) 1

8 71032 16228 Ball bearing 2

9 70861 47927 Lip seal, Viton (77-5130, 5111, 6110, 6111, 6130) 1

9 70826 25203 Lip seal, Teflon 1

10 70833 24842-1 Pump body, cast iron (77-51_) 1

10 70834 24842-2 Pump body, Ni-resist (77-61_) 1



70603 48394-2 7 roller pump repair kit (Viton seals)70-7700RK

70604 48394-4 7 roller pump repair kit (Teflon seals)

70616 25228 7 roller pump Old style Repair Kit ¾” Rollers



70826 25203 Shaft Seal, Teflon 2

70827 24829 Seal Ring 1

70861 47927 Shaft seal, Viton A 2

70885 22059 Old Style ¾” roller


12 8 9

1056

4

3

9 81

7

DEL

AV

AN

7 R

OLL

ER P

UM

P ROLLER PUMP CAPACITIES AND INPUT POWER (BASED ON WATER)

SPEED 0 KPA 200 KPA 500 KPA 700 KPA 1000KPA 1500 KPA

MODEL (RPM) L/MIN KW L/MIN KW L/MIN KW L/MIN KW L/MIN KW L/MIN KW

7 roller 450 45.4 .22 42.0 .37 37.1 .60 34.8 .86 31.7 1.16 27.6 1.53

17.5 mm 540 56.2 .26 52.6 .48 47.9 .78 45.4 .99 41.6 1.38 37.5 1.88650 66.3 .30 61.7 .53 58.3 .87 54.9 1.16 51.5 1.59 48.1 2.18750 75.7 .34 71.9 .62 67.4 .97 65.5 1.29 61.7 1.88 58.1 2.50850 85.2 .37 81.4 .67 77.6 1.07 75.0 1.44 71.6 2.09 66.8 2.80

ROLLER PUMP CAPACITIES AND INPUT POWER (BASED ON WATER)SPEED 0 PSI 25 PSI 50 PSI 100 PSI 200 PSI

MODEL (RPM) GPM HP GPM HP GPM HP GPM HP GPM HP

7 roller 11/16” 450 12.0 .30 11.2 .50 10.4 .60 9.2 1.1 7.3 2.0

540 15.0 .35 14.0 .60 13.2 .75 12.0 1.3 9.9 2.5650 17.5 .40 16.5 .70 15.8 .85 14.5 1.5 12.7 2.9750 20.0 .45 19.2 .80 18.4 1.00 17.2 1.7 15.2 3.3850 22.5 .50 21.5 .85 21.0 1.10 19.9 1.9 17.7 3.7





70014 8800C-R X88-5111 8 roller side port - reverse rotation pump70016 8800N X88-6110 8 roller side port with Ni-resist housing & rotor70017 8800D X88-7110 8 roller side port Diamond series pump70884 33680 Torque Arm & Chain


1 70813 15334 Snap ring 2

2 70828 46209 Nameplate 1

3 70815 15341 Cap screw 4

4 70827 24829 Seal ring 1



7 70831 31666-1 End plate, cast iron (88-5110) 1

7 70832 31666-2 End plate, Ni-resist (88-6110) 1

8 71032 16228 Ball bearing 2

9 70861 47927 Lip seal, Viton 2

10 70837 24842-3 Pump body, cast iron (88-5110) 1

10 70838 24842-4 Pump body, Ni-resist (88-6110_) 1




70614 18768 8 roller pump repair kit old style 11/16” rollers



70827 24829 Seal Ring 1

70861 47927 Shaft seal, Viton A 2

70885 22059 Old Style ¾” roller

SPECIFICATIONS♦ For 540 and 1000 rpm PTO driven applications.♦ Delivers up to 24 gpm♦ Pressures to 300 psi♦ 15/16” shaft♦ 3/4” ports♦ Max. Recommended Pressure: 300 psi (2000 kPa)♦ Max. Recommended Temperature: 120°F (50° C)♦ Max. Recommended Motor Speed: 1000 rpm


12

8 9

10

6 5

4

7 9

81

3

ROLLER PUMP CAPACITIES AND INPUT POWER (BASED ON WATER)SPEED 0 KPA 200 KPA 500 KPA 700 KPA 1000KPA 1500 KPA 2000 KPA

MODEL (RPM) L/MIN KW L/MIN KW L/MIN KW L/MIN KW L/MIN KW L/MIN KW L/MIN KW

8 roller 450 41.0 .13 36.5 .25 32.0 .53 29.5 .73 25.0 1.1 19.5 1.6 14.8 2.2

17.5 mm 540 49.2 .16 45.0 .34 40.1 .64 37.5 .84 33.3 1.2 27.2 1.9 23.1 2.5650 58.5 .18 55.5 .38 50.1 .79 47.5 1.1 43.0 1.5 37.5 2.3 33.0 2.9750 68.0 .21 64.0 .44 59.5 .94 57.0 1.3 52.5 1.8 47.0 2.6 43.0 3.4850 77.0 .26 73.5 .53 68.2 1.1 66.0 1.5 62.0 2.0 56.0 2.9 51.5 3.81000 90.8 .32 87.4 .70 82.5 1.3 79.5 1.6 75.3 2.3 69.3 3.3 64.7 4.3

ROLLER PUMP CAPACITIES AND INPUT POWER (BASED ON WATER)SPEED 0 PSI 25 PSI 50 PSI 100 PSI 200 PSI 250 PSI 300 PSI


8 roller 11/16” 450 10.8 .17 9.7 .30 9.0 .50 7.8 .95 5.5 2.0 4.6 2.5 3.7 3.0

540 13.0 .20 12.1 .40 11.3 .60 10.0 1.1 7.6 2.3 6.7 2.9 6.0 3.5650 15.6 .24 14.7 .45 13.8 .76 12.7 1.5 10.3 2.8 9.4 3.4 8.6 4.0750 18.0 .29 17.1 .51 16.3 .90 15.0 1.7 12.7 3.2 11.8 3.9 11.0 4.6850 20.3 .34 19.6 .63 18.8 1.1 17.5 2.0 15.1 3.6 14.2 4.4 13.5 5.21000 24.0 .40 23.2 .85 22.4 1.3 21.0 2.3 18.7 4.0 17.8 5.0 17.0 6.0


H y p r o S i l v e r S e r i e s X L Pu m p s a n d S u p e r Ro l l e r s

Hypro was the first manufacturer to offer an alloy that is harder, smoother and more resistantto wear and corrosion than standard casting materials used for sprayer pumps. This alloy hasbeen appreciated for years in Hypro’s Silver Series XL™ roller pumps.

The material in Hypro’s Silver Series XL™ pumps provides maximum pump life. In tests using Roundup®herbicide, Hypro Silver Series XL™ roller pumps ran up to 10 times longer than standard cast iron roller pumps…and over 3 times longer than Ni-Resist roller pumps! Even after 1000 hours - long after the other pumps hadfailed- the Silver Series XL™ pumps still met new pump performance specs!Matched with Hypro’s Super Rollers, these pumps provide superior resistance to wear and/or corrosion whenhandling today’s powerful agricultural chemicals. (See below for details on Super Rollers).Hypro and your herbicide: A “Total Value” team.Today’s lower chemical application rates give farmers important economic and environmental benefits. Thosesame benefits expand further with Hypro’s longer running Silver Series XL ™ pumps. They are built to lastlonger and are completely repairable, so they are more economical. Plus, their consistent, precise, pumpperformance ensures greater overall spraying accuracy. That’s good for the environment. For the best “totalvalue”, team up your herbicide with superior Silver Series XL™ roller pumps.

Super Rollers are the result oftwo years of research,development and continuoustesting. These dark blue coloredrollers are made from a specialcombination of materials thatprovide the long life ofpolypropylene rollers and thechemical resistance of nylonrollers. Super rollers do not swellin water and maintain theirperformance when exposed tochemical carriers such as xylene.They are ideal for use with water-soluble chemicals and emulsifiableconcentrates.Super Rollers can be used for thevast majority of agriculturalapplications, and because they areversatile, there is usually no needto switch rollers or pumps. Onecaution— Super Rollers should notbe used with acids. Hyprorecommends using teflon or polyrollers or one of Hypro’s polycentrifugal pumps.


H y p r o R o l l e r P u m p C o m p a r i s o n s

Herbicide Users—Get up to 10 times longer pump life with Hypro Silver Series XL™ Roller Pumps!

Silver Series XL™ Ni-Resist Cast Iron

The three pumps shown above were photographed after being tested with a 30:1 mix of waterand Roundup® herbicide. The Ni-Resist and cast iron indicate damage from pitting andcorrosion, but the Silver Series is in like new condition after more than 1000 hours of use.

Herbicide users get up to 10 times longerpump life!♦Cast iron pumps lasted to 140 hours before failure

♦Ni-Resist pumps lasted to 332 hours before failure

♦Silver Series pumps ran over 1000 hours and still metnew pump specs!

PUMPS AND COUPLERS 1-11SPRAYER PARTS CATALOGUE©2003

H y p r o 4 R o l l e r P u m p


Shaft CouplingSee Page 96-99

REF. PART REPLACES DESCRIPTION QTY. NO. REQ.

1 71000 0100-4001C Body (cast iron) for 4001 C pump 11 71001 0100-4001N Body (Ni-resist) for 4001N pump 11 71002 0100-4101C Body (Cast iron) for 4101C pump 11 71003 0100-4101N Body (Ni-resist) for 4101N pump 11 73900 0100-4001X Body (SilverCast) with std. seal (4001) 11 73901 0100-4101X Body (SilverCast) with std. seal (4101) 12 71004 0200-4001C Endplate (cast iron) for 4001C 12 71005 0200-4001N Endplate (ni-resist) for 4001N 12 71006 0200-4101C Endplate (cast iron) for 4101C 12 71007 0200-4101N Endplate (Ni-resist) for 4101N 12 73902 0200-4001X Endplate (SilverCast) with std. seal (4001) 12 73903 0200-4101X Endplate (SilverCasst) with std. seal (4101) 13 71008 0300-4001C Rotor & shaft assy for 4001C 13 71009 0300-4001N Rotor & shaft assy for 4001N 13 71010 0300-4101C Rotor & shaft assy for 4101C 13 71011 0300-4101N Rotor & shaft assy for 4101N 13 73904 0300-4001X Rotor (SilverCast) & shaft assembly (4001) 13 73905 0300-4101X Rotor (SilverCast) & shaft assembly (4101) 1

3A 71012 0550-6600 Shaft 14 71013 2230-0002 Rotor set screw 14 73906 2230-0016 Rotor set screw (SilverCast only) 15 71014 1002-0002 Polypropylene rollers 45 71015 1005-0002 Rollers (super) standard 45 71016 1001-0002 Buna-N rubber rollers (optional) 45 71017 1055-0002 Teflon rollers (optional) 46 71018 1720-0104 O-ring gasket for endplate 17 71019 2200-0018 Endplate screw 48 71020 2107-0002 Standard seal (Viton) 28 71021 2102-0001 Optional seal (Buna-N) 28 71022 2103-0001 Optional seal (leather) 29 71592 2000-0010 Ball bearing (sealed) 2* 71024 1800-0001 Bearing retainer ring 1

12 71025 3420-0024 Base kit for mounting pump to electric 1motors w 3½” shaft centerline

13 71026 3420-0025 Base kit for mounting pump to gas 1engines w/4 3/16" shaft centerline

13 71027 3420-0026 Base kit for replacing old style 4000 1series pumps

15 71028 1320-0016 Adapter kit w 4 setscrews for gas engine 115 71029 1320-0024 Adapter kit w 4 setscrews for cub 1

tractor drive*Not Shown

PART NO. REPLACES DESCRIPTION

Pumps operating up to 1800 rpm

70040 4001C Cast iron pump 5/8” solid shaft

70041 4001N Ni-resist pump 5/8” solid shaft

70073 4001XL Silver Cast 5/8” solid shaft

70088 4001C-R Cast iron pump 5/8” solid shaft,reverse rotation

70039 4101N-EH 12 volt Ni-resist 4 roller pump1900 rpm

73928 2570-0013 12 volt motor for 70039

Pumps operating up to 2600 rpm

70042 4101C Cast iron pump 5/8” solid shaft

70043 4101N Ni-resist pump 5/8” solid shaft

70074 4101XL Silver Cast 5/8” solid shaft

70089 4101N-H Ni-resist pump ½” hollow shaft

Use series 4001/4101 as a “pressure” pump for spraying,atomizing or blending insecticides, herbicides, fumigants, etc., oras a transfer pump for water, brine, oils, solvents, and manychemicals, or as a circulating pump for lubricants, coolants, andrinsing solutions.

Body, endplate and rotor: Cast iron or Ni-resistShaft: 5/8” stainless steelPorts: ¾” NPTHorsepower: .14 to 1.10Bearings: Shielded ball type, factory lubricatedRollers: Super standard polypropylene, nylon, teflon, or Buna-NoptionalSeals: Viton Standard, Buna-N or Leather optionalSeries 4001, for electric motor drive: Output to 9 gpm;pressure to 150 psi; speed to 1800 rpm, temperature to 140° FSeries 4101, for gas engine drive: Output to 7 gpm;pressure to 150 psi; speed to 2600 rpm; temperature to 140°F

LENGTH WIDTH HEIGHT SHAFT SHAFT PORTHEIGHT DIAMETER NPT

5 11/32” 45/8” 3” 1¾” 5/8” ¾”


70620 3430-0390 4 roller pump repair kit (super Rollers)

70621 3430-0158 4 roller pump repair kit (polypropylene rollers)PART NO. REPLACES DESCRIPTION QTY/KIT

71014 1002-0002 Roller, Polypropylene 4

71015 1005-0002 Roller, super 4

71018 1720-0104 O-ring gasket for end plate 1

71020 2107-0002 Viton seal 2

SPEED 0 PSI 25 PSI 50 PSI 75 PSI 100 PSI 125 PSI 150 PSI


4001 1800 9.1 .14 8.5 .30 8.0 .46 7.6 .62 7.3 .78 7.0 .95 6.7 1.1

4101 2600 7.2 .16 6.9 .30 6.6 .46 6.4 .62 6.0 .76 5.7 .92 5.4 1.08

4001/4101 4101N-EH



1700


70044 1700C Cast iron pump

70045 1700N Ni-resist pump

70072 1700CR Cast iron pump, reverse rotation

70075 1700XL Silver cast LENGTH WIDTH HEIGHT SHAFT SHAFT PORT

HEIGHT DIAMETER NPT

7 23/32” 8¼” 6 7/32” 33/8” 15/16” 1”

The 1700 series handles a variety of liquids: water, herbicides, insecticides,emulsions, aromatic solvents, fertilizer and wettable powder. Use wheremoderate flow and pressure is desirable.Output: 20.5 gpm at 50 psiShaft: 15/16”Ports: 1” NPTHorsepower: .05 to 3.65




1 71030 1800-0003 Retainer ring 12 76510 2300-0020 Bearing cover 13 71032 2008-0001 Ball bearing (sealed) 24 71033 2112-0003 Seal (Viton) standard 24 71034 2112-0001 Seal (Buna-N) optional 24 71035 2103-0002 Seal (leather) optional 25 71036 2210-0005 Bolts for end plate 66 71037 0200-1700C End plate (cast iron) includes seal 16 71038 0200-1700N End plate (Ni-resist) includes seal 16 73907 0200-1700X End plate (SilverCast) with seal 17 71039 1720-0099 O-Ring gasket for end plate 18 71040 0300-1700C Rotor (cast iron) with shaft 18 71041 0300-1700N Rotor (Ni-resist) with shaft 18 73908 0300-1700X Rotor (SilverCast) with shaft 1

8A 71042 0301-1700C Rotor (cast iron) w/shaft (reverse rot.) 18A 71043 0301-1700N Rotor (Ni-resist) w/shaft (reverse rot.) 19 71044 0500-1502 Solid shaft only 110 71045 1610-0005 Spline key 111 71046 2230-0018 Set screw only 111 73909 2230-0034 Set screw (Silvercast only) 112 71047 1002-0005 Roller (polypropylene) 512 71048 1005-0005 Roller, Super Standard 512 71049 1055-0005 Roller (Teflon) optional 513 71050 0100-1700C Body (cast iron) includes seal 113 71051 0100-1700N Body (Ni-resist) includes seal 113 73910 0100-1700X Body (SilverCast) with seal 114 71052 3420-0010 Base kit (base and 4 bolts) 1


70625 3430-0383 5 roller pump repair kit(super rollers)

70623 3430-0160 5 roller pump repair kit(polypropylene rollers)


71047 1005-0005 Roller, Super 5

71039 1720-0099 O-ring gasket for endplate 1

71033 2112-0003 Viton seal 2

71034 2112-0004 Buna-N seal (optional)

Output to 45 gpm - pressure to 200 psiSpeed to 1000 rpm - temperature to 140°F

SPEED 0 PSI 25 PSI 50 PSI 75 PSI 100 PSI


1700 540 24.5 .13 20.5 .96 17.7 1.78 16.3 2.57 14.3 3.3

2A1

23

4

56

711

1289

10

134

3

109

11 8A

14


SPEED 0 PSI 50 PSI 100 PSI 150 PSI

MODEL (RPM) GPM HP GPM HP GPM HP GPM HP


1500

Series 1500 six roller pumps, with theirlarge capacity and high pressure capability,can be used for fire fighting in addition toother roller pump applications. They canadapt to1 3/8” or 1 ¾”, 1000 rpm PTO shaft as wellas 540 rpm. A large variety of chemicals canbe used.Output: 30 gpm at 540 rpm, 50 psiMaximum Pressure: 150 psiMaximum speed: 800 rpmShaft: 15/16” Ports: 1½” NPTHorsepower: .5 to 5.5




70076 1502XL Silver cast


7 23/32” 8¾” 8 1/8” 5” 15/16” 1½”


1

2 34

56 7

11

12

8 910

134

3

148A

11

109



70624 3430-0163 Repair kit (Poly rollers,Buna-N seals)

70625 3430-0383 Repair kit (Super rollers,Viton seals) 2 o-rings

70626 3430-0386 Repair kit (Super rollers,Viton seals) 1 o-ring

70627 3430-0387 Repair kit (super rollers,Buna-N seals)


71034 2112-0001 Buna-N seal 2

71033 2112-0003 Viton seal (optional) 2

71183 1720-0003 O-Ring gasket 1



1 71030 1800-0003 Retainer ring 12 76510 2300-0020 Bearing cover 13 71032 2008-0001 Ball bearing (sealed) 24 71034 2112-0001 Seal (Buna-N) standard 24 71033 2112-0003 Seal (Viton) optional 24 71035 2103-0002 Seal (leather) optional 25 71053 2210-0026 Bolts for end plate 66 71054 0200-1500C End plate (cast iron) includes seal 16 71055 0200-1500N End plate (Ni-resist) includes seal 16 73911 0200-1500X End plate (SilverCast) with seal 17 71183 1720-0003 O-ring gasket for end plate 18 71056 0300-1502C Rotor (cast iron) with shaft 18 71057 0300-1502N Rotor (Ni-resist) with shaft 18 73912 0300-1502X Rotor (SilverCast) with shaft 1

8A 71058 0301-1502C Rotor (cast iron) w/shaft (reverse rot.) 18A 71059 0301-1502N Rotor (Ni-resist) w/shaft (reverse rot.) 19 71044 0500-1502 Solid shaft only 110 71045 1610-0005 Spline key 111 71046 2230-0018 Set screw only 111 73909 2230-0034 Set screw (Silvercast only) 112 71047 1002-0005 Roller (polypropylene) 612 71048 1005-0005 Roller, Super Standard 612 71049 1055-0005 Roller (Teflon) optional 613 71060 0100-1500C Body (cast iron) includes seal 113 71061 0100-1500N Body (Ni-resist) inlcudes seal 113 73913 0100-1500X Body (SilverCast) with seal 114 71062 3420-0004 Base kit (base , 4 bolts & washers) 1

1500 540 34 .75 30 1.75 28 2.75 26 3.75

REPAIR KIT FOR 6 ROLLER PUMP

ROLLER PUMP CAPACITIES AND INPUT POWER (BASED ON WATER)



6500

Along with the 7560, the series 6500 is one of the most widely used pumps on farms today. It’s an economicalway to handle: water, herbicides, insecticides, emulsions, aromatic solvents, fertilizer and wettable powder.Output: 7.4 gpm at 540 rpm, 50 psi, 15gpm at 1000 rpm, 50 psiMaximum Pressure: 300 psiShaft:5/8” Ports: ¾” NPTHorsepower: .15 to 4.5




70050 6500CR Cast iron pump reverse rotation

70077 6500XL Silver Cast



1 71024 1800-0001 Bearing retainer ring 12 76511 2300-0021 Bearing cover 13 71592 2000-0010 Ball bearing (sealed) 24 71020 2107-0002 Seal (Viton) standard 24 71021 2102-0001 Seal (Buna-N) optional 24 71022 2103-0001 Seal (leather) optional 25 71063 2210-0004 Cap screw for end plate 46 71064 0200-6600C End plate (cast iron) includes seal 16 71065 0200-6600N End plate (Ni-resist) includes seal 16 73914 0200-6600X End plate (SilverCast) with std. seal 17 71066 1720-0008 O-Ring gasket for end plate 18 71067 1052-0004 Rubber roller (optional) 69 71068 1005-0004 Super roller standard 69 70820 1002-0004 Polypropylene roller 610 71070 0300-6600C Rotor with shaft (cast iron) 110 71071 0300-6600N Rotor w/shaft (Ni-resist) 110 73915 0600-6600X Rotor (SilverCast) with shaft 111 71072 0500-6600 Shaft only (includes set screw) 112 73916 2230-0007 Set screw (Silvercast only) 113 71073 0100-6600C Body (cast iron) includes seal 113 71074 0100-6600N Body (Ni-resist) includes seal 113 73917 0100-6600X Body (SilverCast) with seal 119 71029 1320-0024 Adapter for Cub 1 inch PTO 121 71076 3420-0023 Base kit for pump (includes bolts) 1

12 3 4

56

7

89

10

11

12

19

13 4 3



5 11/32” 6” 5 1/32” 3 5/32” 5/8” ¾”


70628 3430-0380 6 roller pump repair kit(super rollers)


71068 1005-0004 Super rollers 6

71066 1720-0008 O-Ring gasket for endplate 1

71020 2107-0002 Viton seal 2




6500 540 9.1 .21 7.4 .58 6.5 .81 5.6 1.13 4.8 1.44 4.0 1.77 3.3 2.10

6500 1000 16.5 .50 15.1 1.04 14.4 1.44 13.6 2.06 12.9 2.58 12.1 3.14 11.3 3.74


21



7700

Plenty of pump for both spraying and agitation - 13 gpmat 50 psi at 540 rpm PTO speed. Designed for wettablepowder herbicides and insecticides. Avoids clogging andhelps assure a proper and uniform mix.Output: 12.9 gpm at 540 rpm, 50 psiMaximum Pressure: 200 psiShaft:15/16” Ports: ¾” NPTHorsepower: .11 to 3.3




70078 7700XL SilverCast


6 7/8” 6 5/8” 6” 3 ½” 15/16” ¾”



1 71030 1800-0003 Retainer Ring 12 76510 2300-0020 Bearing Cover 13 71032 2008-0001 Ball bearing (sealed) 24 71034 2112-0001 Seal (Buna-N) optional 24 71033 2112-0003 Seal (Viton) standard 24 71035 2103-0002 Seal (leather) optional 25 71063 2210-0004 Bolts for end plate 66 71077 0200-7700C End plate (cast iron) includes seal 16 71078 0200-7700N End plate (Ni-resist) includes seal 16 73918 0200-7700X End plate (SilverCast) with seal 17 71079 1720-0014 O-Ring gasket for end plate 18 71080 0300-7700C Rotor (cast iron) with shaft 18 71081 0300-7700N Rotor (Ni-resist) with shaft 18 71082 0301-7700C Rotor (cast iron) w/shaft (reverse rot.) 18 71083 0301-7700N Rotor (Ni-resist) w/shaft (reverse rot.) 18 73919 0300-7700X Rotor (SilverCast) with shaft 19 71084 0550-7400 Solid shaft only (include set screw) 1* 73916 2230-0007 Set screw (SilverCast only) 1

11 71045 1610-0005 Spline key 112 71068 1005-0004 Super roller 712 70820 1002-0004 Roller (Polypropylene) 713 71085 0100-7700C Body (cast iron) includes seal 113 71086 0100-7700N Body (Ni-resist) includes seal 113 73920 0100-7700X Body (SilverCast) with seal 114 73496 2404-0052 1 inch hose barb 115 71087 3420-0010 Base kit for pump (with 4 bolts) 1

* Not Shown



70629 3430-0384 Repair kit (Super rollers,Viton seals)


71068 1005-0004 Super rollers 7


71033 2112-0003 Viton seal 2


SPEED 0 PSI 50 PSI 100 PSI 150 PSI 200 PSI


7700 540 14.2 .23 12.9 .56 11.9 1.10 11.2 1.64 10.3 2.22


REPAIR KIT FOR 7 ROLLER PUMP

HY

PR

O 8

RO

LLER

PU

MP


7560

The series 7560 offers a variety of choices in materials for rollers,shaft seals and pump housing. The choice reflects your pumpingneeds: water, herbicides, insecticides, emulsions, aromatic solvents,fertilizer and wettable powder. Heavy duty construction with 15/16”diameter steel shaft.Output: 11.4 gpm at 540 rpm, 50 psi, 22 gpm at 1000 rpm, 50 psiMaximum Pressure: 300 psiShaft:15/16” Ports: ¾” NPTHorsepower: .25 to 6



1 71030 1800-0003 Retainer Ring 1* 76510 2300-0020 Bearing Cover 13 71032 2008-0001 Ball bearing (sealed) 24 71033 2112-0003 Seal (Viton) standard 24 71034 2112-0001 Seal (Buna-N) optional 24 71035 2103-0002 Seal (leather) optional 25 71063 2210-0004 Cap screw for end plate 66 71090 0204-7500C End plate (cast iron) includes seal 16 71091 0204-7500N End plate (Ni-resist) includes seal 16 73921 0204-7500X End plate (SilverCast) with seal 17 71079 1720-0014 O-ring gasket for end plate 18 71068 1005-0004 Super roller standard 88 70820 1002-0004 Roller (polypropylene) optional 88 71067 1052-0004 Roller (Buna-N) optional 89 71092 0308-7560C Rotor (cast iron) with shaft 19 71093 0308-7560N Rotor (Ni-resist) with shaft 19 73922 0308-7560X Rotor (SilverCast) with shaft 110 71094 0500-7400 Solid shaft only 111 71045 1610-0005 Spline key 112 71095 0104-7500C Body (cast iron) includes seal 112 71096 0104-7500N Body (Ni-resist) includes seal 112 73923 0104-7500X Body (SilverCast) with seal 114 71097 3420-0003 Base kit (base, bolts, washers) 1

* Not Shown





70055 7560CR Cast iron pump with base kit,reverse rot.

70079 7560XL SilverCast


6 13/16” 65/8” 5 15/16” 3 3/8” 15/16” ¾”


70630 3430-0381 Pump repair kit(Super rollers)


71068 1005-0004 Super rollers 8


71033 2112-0003 Viton seal 2




7560C 540 11.8 .25 11.2 .75 10.4 1.25 9.8 1.50 9.1 2 8.3 2.50 7.8 3

7560C 1000 22.9 1 21.9 2 21.4 3 20.5 4 19.7 5 18.9 6


13

4

56

7

89 11

14

124

3

10



Hyp ro “Sma l l Twin” P i s ton Pump

5300 Use leather cups for pest control applications and general chemical spraying insecticides, herbicides,fungicides, aromatic solvents. Use rubber cups for water, soaps and detergent solutions. Use teflonfor continuous, hot service (from 100° to 140° F) on clean, non-abrasive liquids (including water,soaps, and detergents). Pump can be driven in either direction without changing inlet and outlet.

REPLACEMENT PARTS FOR PISTON PUMP

REPAIR KIT FOR PISTON CUP & GUIDE

PISTON PUMP CAPACITIES AND INPUT POWER(BASED ON WATER)

SPEED 100 PSI 200 PSI 400 PSI 500 PSIMODEL (RPM) GPM HP GPM HP GPM HP GPM HP

5320 1800 2.26 .32 2.25 .44 2.21 .66 2.20 .79

5/8 SHAFT OUTPUT @ CUPPART NO. REPLACES TYPE 1800 RPM MATERIAL WT.

70056 5320C-RX Solid 2 gpm Rubber 10

70057 5330C-RX Solid 3 gpm Rubber 10

70058 5320C-HRX Hollow 2 gpm Rubber 9 1/2

70059 5330C-HRX Hollow 3 gpm Rubber 9 1/2

MODEL SUB ASSEMBLEY COMPLETE ASSEMBLYPUMP PART NO. REPLACES PART NO. REPLACES

5315H 71100 5501-5315 71108 5500-5315

5320H 71101 5501-5320 71109 5500-5320

5325H 71102 5501-5325 71110 5500-5325

5330H 71103 5501-5330 71111 5500-5330

5315 71104 5001-5315 71112 5000-5315

5320 71105 5001-5320 71113 5000-5320

5325 71106 5001-5325 71114 5000-5325

5330 71107 5001-5330 71115 5000-5330

Sub Assemblies - Include shaft (ref. 12 or 15) with cam bearing,grease fitting assembly (ref. 10), set screw for hollow shaft (ref.13) and spline key (ref. 16 or 14).Complete Assemblies - Include the Sub assembly plus partsidentified by reference numbers 23-26


70631 3430-0007 Piston repair kit w/leather cups 1

70632 3430-0009 Piston repair kit w/rubber cups 1

70633 3430-0030 Piston repair kit w/Teflon cups 1

71116 1440-0004 Piston guide 2


70634 3430-0008 Leather cup kit w/guides

70635 3430-0010 Rubber cup kit w/guides

70636 3430-0046 Teflon cup kit w/guides

REF PART NO. REPLACES DESCRIPTION QTY.REQ.

2 in kit Piston cap screw 2

3 in kit Washer gasket (always use new 2one when replacing piston assembly

4 70631 3430-0007 Piston repair kit (leather cups) 1

4 70632 3430-0009 Piston repair kit (rubber cups) 1

4 70633 3430-0030 Piston repair kit (Teflon cups) 1

5 in kit Piston cup spreader 2

6 in kit Cup backing plate 2

7 71116 1440-0004 Piston guide 2

8 71117 0502-5300 Connecting rod (replaces 501-5300) 1

9 71118 0608-5300 Grease fitting safety cover 1

10 71121 2405-0006 Grease Fitting

12 - - Crankshaft assembly- see table Hollow Shaft

13 71120 2230-0017 Set screw for hollow shaft

15 - - Crankshaft assembly- see table solid shaft

16 71122 1610-0007 Spline key for solid shaft 2

14 71123 1610-0011 Spline key for hollow shaft 1

17 71124 2210-0006 Headbolt 8

18 71125 0204-5300C Cylinder head (cast iron) 2

19 71126 1720-0038 O-Ring for cylinder head 2

20B 71127 1720-0079 O-Ring for cylinder sleeve 2

20 71128 3550-0019 Cylinder sleeve assembly (Ni-resist) 2

21 71129 3400-0073 Unitized valve 4(stainless steel poppet spring & seat)

22 71130 0100-5300C Body (cast iron) 1

24 71131 2130-0007 Bearing shield 1

25 71032 2008-0001 Main bearing (ball bearing) 2

26 71133 1810-0013 Bearing retainer ring (shaft) 2

27 71134 1820-0025 Bearing retainer ring (housing) 1

28 71135 1510-0022 Mounting base 1

29 71136 2820-0040 Torque arm for electric motor mount 1

30 71137 2820-0028 Torque arm for gas engine mount 1

31 71029 1320-0024 Adapter for cub tractor PTO shaft 1

SHAFT SHAFT PORTLENGTH WIDTH HEIGHT HEIGHT DIA NPT

Solid shaft model

5 19/32" 5 1/8" 6 13/16" 3 1/2" 5/8" 1/2 NPT

Hollow shaft model

5 7/32" 5 1/8" 5 1/2" 2 3/4" 5/8" ID 1/2 NPT

CouplersSee Page96-99


Hypro Twin Piston Plunger Pump

Use leather cups for pest control applications and general chemical spraying insecticides,herbicides, fungicides, aromatic solvents. Use rubber cups for water, soaps and detergentsolutions. Use teflon for continuous, hot service (from 100° to 140° F) on clean, non-abrasiveliquids (including water, soaps, and detergents).Pump can be driven in either direction withoutchanging inlet and outlet. Solid shaft models include mounting base. Maximum pressure 1000psi. Maximum speed 1800 rpm.

5/8 SHAFT OUTPUT @ PLUNGERPART NO. REPLACES TYPE 1800 RPM MATERIAL WT.

70060 5321C 5/8"Solid 2.15 gpm Stainless steel 11

70038 5322C-H Hollow 5/8” 2.00 gpm Ceramic plunger 11

70037 5321C-H Hollow 5/8” 2.15 gpm Stainless steel 11

SPEED 100 PSI 200 PSI 400 PSI 500 PSI 600 PSI 800 PSI 1000 PSIMODEL (RPM) GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP

5321,5322 1750 2.23 .33 2.22 .49 2.22 .77 2.22 .88 2.20 1.04 2.20 1.32 2.15 1.53

PISTON PUMP CAPACITIES AND INPUT POWER (BASED ON WATER)

CRANKSHAFT ASSEMBLIESPart No. 73924 - Solid Shaft Sub-Assembly No. 5001-5321 con-sist of one each of the following parts: No. 0500-5321 crankshaft;No. 1600-0014 crankpin retainer,, No. 2007-0029 cam bearing, No.2405-0006 grease fitting assembly: No. 1610-0007 keyPart No. 73925 - Solid Shaft Assembly No. 5000-5321 consistsof one No. 5001-5321 crankshaft sub-assembly, two No. 1810-0013retainer rings, two No. 2008-0001 main bearings, one No. 2130-0007 bearing shieldPart No. 73926 - Hollow Shaft Sub-Assembly No. 5501-5321consists of one No. 0550-5321 crankshaft, one No. 1600-0014 crank-pin retainer, one No. 2007-0029 cam bearing, one No. 2405-0006grease fitting assembly, one No. 1610-0011 key, two No. 2230-0017 set screwsPart No. 73927 - Hollow Shaft Assembly No. 5500-5321 con-sists of one No. 5501-5321 crankshaft sub-assembly, two No.1810-0013 retainer rings, two No. 2008-0001 main bearings, oneNo. 2130-0007 bearing shield

REPAIR KIT FOR PISTON STACK & GUIDEPART NO. REPLACES DESCRIPTION

*70654 3430-0144 Plunger stack parts kit (seal rings guides,O-Rings, seal assys., capscrews, washers

70681 3430-0145 Plunger parts kit (all above plus plungers)


*2 71420 2220-0039 Socket head capscrew 2

*3 71421 2270-0042 Washer 2

4 71422 1830-0056 Retainer 2

*5 71412 2150-0027 Seal assembly 2

6 71423 1830-0054 Seal retainer 2

*7 71127 1720-0079 O-Ring for seal retainer 2

*8 71424 1440-0037 Guide 2

*9 71425 1720-0064 O-Ring for seal ring 2

*10 71426 1440-0010 Seal ring 2

11 71427 1830-0053 Guide retainer 2

12 71428 3500-0021 Plunger 2

13 71117 0502-5300 Connecting rod 1

14 71118 0608-5300 Safety cover 1

15 71429 2210-0063 Cylinder head bolt 4 or 8

15A 71430 2210-0064 Extra long cyl. head bolt for 5321C 4



18 71432 3430-0197 Set of 4 unitized valve assy. 1 set

19 71433 0108-5300C Body (cast iron) 1

21 71121 2405-0006 Grease fitting assembly 1

22 Crankshaft assy. (see listing) 1

24 71120 2230-0017 Set screws for hollow shaft 2

25 71123 1610-0011 Spline key for hollow shaft 1

26 Crankshaft assy. (see listing) 1

27 71122 1610-0007 Spline key for solid shaft 1

28 71131 2130-0007 Bearing shield 1

29 71032 2008-0001 Main bearing 2

30 71133 1810-0013 Bearing retainer 2

31 71134 1820-0025 Retaining ring (housing) 1

32 71434 1510-0041 Mounting base for 5321C (solid shaft) 1

33 71435 3420-0030 Torque arm kit for 5321C-H 1


COUPLERS SEE PAGES 96-99

5321


H y p r o “ B i g Tw i n” P i s t o n P u m p

REPAIR KIT FOR PISTON STACK & GUIDEPART NO. REPLACES DESCRIPTION

70637 3430-0037 Leather cup kit (ref. 6)

70638 3430-0039 Fabric cup kit (ref. 6)


2 71168 2220-0013 Socket head capscrew 2

3 71169 2270-0012 Washer 2

4 71170 1830-0039 Piston cup spreader 2

5 71171 1410-0054 Backing plate 2

6 70637 3430-0037 Kit with leather cups 1

6 70638 3430-0039 Kit with fabric cups 1

7 71172 1440-0005 Piston guide 2

8 71173 1410-0018 Support ring for 5210C models 2

9 71174 1410-0020 Support ring for 5206C models 2

10 71175 0503-5200 Connecting rod 1

11 71418 0602-5200 Bearing cover (name plate) 1

12 71121 2405-0006 Grease fitting assembly 1

13 Crankshaft - see listing

14 Crankshaft - see listing

15 71165 1810-0001 Retainer ring 2

16 71167 1600-0013 Roll pin 1

17 71045 1610-0005 Key 1

20 71164 1410-0006 Slinger ring 2

21 71163 2005-0002 Main bearing 1

22 71154 2210-0062 Hex head cap screw 8



25 71155 1720-0019 O-Ring for cylinder sleeve 1

26 71156 3550-0007 Cylinder sleeve 2

27 71157 3400-0038 Valve set 4

28 71150 0100-5200C Body (cast iron) 1

29 71152 1510-0024 Base 1



71168 2220-0013 Socket head cap screw 2

71169 2270-0012 Washer 2

71170 1830-0039 Piston cup spreader 2

COUPLERS SEE PAGES 96-99

MODEL CRANKSHAFT ONLY SUB ASSEMBLY COMPLETE ASSEMBLYPUMP PART NO. REPLACES PART NO. REPLACES PART NO. REPLACES

5206C-HN 71138 0550-5206 71142 5503-5206 71146 5501-5206

5210C-HN 71139 0550-5210 71143 5503-5210 71147 5501-5210

5206C-N 71140 0500-5506 71144 5003-5206 71148 5001-5206

5210C-N 71141 0500-5210 71145 5003-5210 71149 5001-5210

Sub Assemblies - Include grease fitting, crankshaft, cambearing and roll pin. (reference no. 20, 21, 35 and 18 or 19)Complete Assemblies - Include ball bearing, slinger rings,retaining rings, crankshaft, cam bearing, grease fitting and rollpin (reference no. 14, 15, 16, 20, 21, 35 and 18 or 19)

CRANKSHAFT ASSEMBLIES

PART NO. REPLACES SHAFT TYPE OUTPUT @ 1800 RPM CUP MATERIAL WT.

70062 5210C-H w/1 3/8 PTO Adapter 10 gpm Leather 16

70063 5206C-H w/1 3/8 PTO Adapter 6 gpm Leather 16

70064 5210C 1" solid shaft 10 gpm Leather 16

70065 5206C 1" solid shaft 6 gpm Leather 16

5200 series pumps have 3/4”NPT ports. Cast iron housing.Maximum operating pressure is400 lbs. Pumps come withleather cups as standard. Maxi-mum output 6 gpm or 10 gpm.Maximum temperature 140° F.

SPEED 100 PSI 200 PSI 400 PSIMODEL (RPM) GPM HP GPM HP GPM HP

5206 600 5.84 .60 5.83 .90 5.80 1.78

5210 600 10.55 1.19 10.41 1.59 10.18 2.83

PISTON PUMP CAPACITIES AND INPUT POWER(BASED ON WATER)

SHAFT SHAFT PORTLENGTH WIDTH HEIGHT HEIGHT DIA NPT

Solid shaft model

5 11/16" 6 3/8" 7 11/16" 4 1/16" 1" 3/4 NPT

Hollow shaft model

6 5/16" 6 3/8" 7 11/16" 4 1/16" PTO 3/4 NPT

5200

Maximum pressure 400 psi.Maximum Speed 800 rpm (5206) 600 rpm (5210)


B a n j o C e n t r i f u g a l P u m p

PERFORMANCE CHART @ 3450 RPM BASED ON WATER150PB, 150PO PERFORMANCE CHART @ 3450 RPM (BASED ON WATER)

Head (ft) 0 11 23 34 46 57 69 80 92

Pressure (PSI) 0 5 10 15 20 25 30 35 40

Flow (GPM) 125 110 95 80 70 50 30 15 0

200PB, 200PO PERFORMANCE CHART @ 3450 RPM (BASED ON WATER)

Head (FT) 0 11 23 34 46 57 69 80 92

Pressure (PSI) 0 5 10 15 20 25 30 35 40

Flow (GPM) 140 120 105 85 70 50 30 15 0

300 PB, 300PO PERFORMANCE CHART @ 3450 RPM (BASED ON WATER)

Head (FT) 0 11 23 34 46 57 69

Pressure (PSI) 0 5 10 15 20 25 30

Flow (GPM) 300 285 240 190 145 85 15

205PB, 205PO PERFORMANCE CHART @ 3450 RPM (BASED ON WATER)

Head (FT) 0 11 23 34 46 57 69 80 92 103

Pressure (PSI) 0 5 10 15 20 25 30 35 40 45

Flow (GPM) 195 180 170 155 145 125 110 85 60 20

SEE NEXT PAGE FORPARTS BREAKDOWN

REPAIR PARTS LIST (VITON) - NEW DESIGNPART NO. BANJO NO. DESCRIPTION

SPP 71529 12713V Viton seal assy. with 316 SS cup & spring

SPP 71530 12719AV Viton body O-Ring

SPP 71531 12717V Viton O-Ring for screw head

SPP 71532 12754V Viton O-Rng segment

SPP 71547 14774VA Viton O-Ring for acorn nut

SPP 71535 12705V Viton check valve

SPP 71559 UV15163V Prime plug O-Ring

SPP 71537 12710V Viton O-Ring for seal assy.

SPP 70687 12000AV Viton repair kit

SPP 70688 12999AV Viton pump seal/O-Ring kit

PUMP ONLY (UNASSEMBLED) – FOR GASOLINEENGINE

PART NO. BANJO NO. DESCRIPTION

SPW 150PO 150PO 1 1/2" pump only (unassembled) accepts 3/4" straight shaft 3-vane impeller

SPW 200PO 200PO 2" pump only (unassembled) accepts3/4" straight shaft 3-vane impeller

SPW 205PO 205PO 2" pump only (unassembled) accepts3/4" straight shaft 5-vane impeller

SPW300PO 300PO 3” poly pump (unassembled) accepts3/4" straight shaft 4-vane impeller

PEDESTAL PUMP AND PUMP ONLY

Pedestal pumps:With the addition of the Banjobearing pedestal, the pump iseasily adaptable to electricpower. A flexible shaft couplingis used between motor andpump shaft.

BEARING PEDESTAL PUMPS - FOR ELECTRICMOTORS


SPW 150PB 150PB 1 1/2" pump/bearing - 3/4" straight shaft with key

SPW 200PB 200PB 2" pump/bearing pedestal - 3/4" straightshaft with key 3-vane impeller

SPW 205PB 205PB 2" pump/bearing pedestal - 3/4" straightshaft with key 5-vane impeller

SPW 300PB 300PB 3" poly pump with bearing pedestal -3/4" shaft

SPP 71538 12882A Bearing Pedestal - 3/4" straight shaftwith key

(Recommended RPM 3450)

POLYPROPYLENE SELF-PRIMING FOR GASOLINE ENGINES WITH 3/4” SHAFTSAND ELECTRIC MOTORS WITH 3/4” SHAFT

UNIVERSAL BASE PLATE ASSEMBLY


SPP 71541 18700 Base Plate Assembly

Complete with bolts, washers, shims and coupling guard


B a n j o C e n t r i f u g a l P u m p

REF PART NO. DESCRIPTION QTY. 1 1/2" 2" 3"

2 71501 Body nuts SS 10 V07019 V07019 V07019

3 71502 Lock washer SS 10 V07018 V07018 V07018

4 71542 Poly pump rear bracket 1 12703A 12703A 12703A

5&6 71504 Seal assembly*+ 1 12713 12713 12713

7 71505 Screw heads O-Ring*+ 4 12717 12717 12717

8 71543 Bracket screws SS 4 12715A 12715A 12715A

9 71507 O-Ring segment*+ 1 12754 12754 12754

10 71508 Body O-Ring*+ 1 12719A 12719A 12719A

11 71544 3 vane poly pump impeller 1 12771A - -

11 71539 5 vane poly pump impeller+ 1 - 12772 -

11 71545 4 vane poly pump impeller+ 1 - - 13771

12 71546 Impeller blt SS 1 12765A 12765A 12765A

13 71547 Impeller blt gasket*+ 1 12774VA 12774VA1 12774VA

14 71548 Impeller hex nut 1 12775A 12775A 12775A

15 71527 Poly pump volute 1 12702A 12702A -

15 71549 Poly pump volute 1 - - 13702A

16 71514 Volute screws SS 2 12725 12725 12725

17 71515 Poly pump check valve+ 1 12705 12705 12705

18 71516 Poly pump body assembly 1 12711A - -

18 71551 Poly pump body assembly 1 - 12712A -

18 71552 Poly pump body assembly 1 - - 13712

19 71518 Body screws SS 10 12720 12720 12720

20 71519 Prime/drain plug 2 12777 12777 -

20 71553 Prime/drain plug 2 - - 13777

21 71554 Prime/drain plug O-Ring*+ 2 UV15163 UV15163 -

21 71555 Prime/drain plug O-Ring*+ 2 - - 13778

25 71524 Upper volute screw SS 1 12900 12900 12900

26 71525 Rear bracket washer SS 4 12901 12901 12901

27 71556 Impeller key 1 12902A 12902A 12902A

28 71557 Poly pump Slinger*+ 1 12706 - -

28 75254 Poly Pump Slinger 1 - 12716 12716

29 71528 O-Ring for seal assembly*+ 1 12710 12710 12710

71538 Bearing pedestal 3 3/4" 1 12882A 12882A 12882Astraight shaft w/key

71558 Impeller removal bolt*+ 1 12099 12099 12099

70663 Pump repair kit 11/2" & 2" pump 12000A 12000A -(consists of items marked with +)

70664 Pump repair kit 3" pump - - 13000(consists of items marked with +)

70684 Pump seal o-ring kit 11/2" & 2" pump 12999A 12999A -(consists of items marked with *)

70685 Pump seal o-ring kit 3" pump - - 13999(consists of items marked with *)

NEW DESIGNReplacement parts for pumps manufactured

beginning September, 1996.Viton replacement parts for new design on previous page.

OLD DESIGNReplacement parts for pumps manufactured

prior to September, 1996.

REF PART NO. DESCRIPTION QTY. 1 1/2" 2"

2 71501 Body nuts 10 V07019 V07019

3 71502 Lock washer 10 V07018 V07018

4 71503 Rear bracket 1 12703 12703

5&6 71504 Seal assembly*+ 1 12713 12713

7 71505 O-Ring for screw heads*+ 4 12717 12717

8 71506 Bracket screws 4 12715 12715

9 71507 O-ring segment*+ 1 12754 12754

10 71508 Body O-Ring*+ 1 12719A 12719A

11 71509 Impeller+ 1 12771 12771

12 71510 Impeller stud 1 12765 12765

13 71511 O-Ring acorn nut*+ 1 12774V 12774V

14 71512 Acorn nut 1 12775 12775

15 71513 Volute 1 12702 12702

16 71514 Volute screws 2 12725 12725

17 71515 Check valve+ 1 12705 12705

18 71516 Body 1 12711A -

18 71517 Body 1 - 12012

19 71518 Body screws 10 12720 12720

20 71519 Prime plug 1 12777 12777

21 71520 O-Ring prime plug*+ 1 12722 12722

22 71521 Drain plug 1 12723 12723

25 71524 Upper volute screw 1 12900 12900

26 71525 1/4" S.S. washer 4 12901 12901

27 71526 Impeller key 1 12902 12902

28 71520 Slinger O-Ring*+ 3 12722 12722

29 71528 Seal O-Ring*+ 1 12710 12710

71538 Bearing pedestal 3/4" 1 12882A 12882Astraight shaft w/key

70660 Pump repair kit 12000 12000(consists of items marked with +)

70661 Pump seal/O-Ring kit 12999 12999(consists of items marked with *)

70662 Viton repair kit 12000V 12000V

70686 Viton repair kit 12999V 12999V

71522 Body plug 12766 12766

71523 Spanner nut 12767 12767


A c e C e n t r i f u g a l P u m p

REPLACEMENT PARTS FOR CENTRIFUGALPUMP

QTY.REF. PART NO. REPLACES DESCRIPTION REQ.

4 71562 31040 Gasket 1

5 71563 GE-6-SS 1" O.D. shaft sleeve, 1stainless steel GE-100

5 71648 GE-6-SS-A 1" O.D. shaft sleeve GE-100-A 1

6 71565 GE-7-V 1" rotary seal, Viton 1

7 71566 GE-8-A O-Ring for GE-6A-SS shaft sleeve 1

8 71567 GE-9 Bracket 1

9 71568 30100 1 1/4" x 1" volute 1

10 71569 GE-26 Impeller, cast iron GE100 1

10A 71649 GE-26-A Impeller, cast iron GE100A 1

12 71572 41110 1/8" N.P.T. pipe plug 4

12 71573 41120 1/8" N.P.T. pipe plug, 4stainless (opt.)

13 71574 GE-54 Slinger 1

REPAIR KITS FOR CENTRIFUGAL PUMPPART NO. REPLACES DESCRIPTION

70670 RK-GE100 Seal repair kit (older model)

70671 RK-GE100A Seal repair kit (newer model)

PART NO. REPLACES DESCRIPTION QTY./KIT

71565 GE-7-V 1" rotary seal, Viton 1

71562 31040 Gasket 1

71566 GE-8-A O-Ring for GE-6 shaft sleeve 1

GASOLINE ENGINE MOUNTED

GE100-ANote: GE-100 engines have 1/2" dia. shaft; GE-100-A Engines have 5/8" dia. shaft


MODEL 661-CPUMP 0 PSI 50 PSI 100 PSI 150 PSI 200 PSI 250 PSI 300 PSISPEED GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP

400 rpm 7.0 .07 4.8 .49 4.0 .75 3.0 .80 1.5 1.00 - - - -

540 rpm 10.0 .10 9.0 .60 7.6 .95 6.8 1.2 5.7 2.0 4.2 2.2 3.5 3.0

800 rpm 14.5 .20 13.3 .92 12.5 1.28 12.0 1.75 11.1 2.25 10.0 2.75 9 3.25

1000 rpm 17.5 .25 16.8 1.00 15.8 1.75 15.0 2.50 14.4 3.00 13.2 4.00 11.8 4.50

MODEL 881-CPUMP 0 PSI 50 PSI 100 PSI 150 PSI 200 PSI 250 PSI 300 PSISPEED GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP GPM HP

400 rpm 9.8 .25 7.8 .50 6.0 1.00 4.1 1.25 3.5 1.45 3.1 1.8 2.5 2.25

540 rpm 12.7 .33 10.9 .75 9.5 1.2 8.9 1.62 7.1 2.20 6.5 2.68 5.9 3.3

800 rpm 18.6 .90 17.1 1.25 15.2 1.85 14.5 2.25 12.6 3.10 11.8 3.90 10.5 4.25

1000 rpm 22.1 1.40 21.0 1.70 19.2 2.50 18.7 3.40 17.6 4.22 16.9 4.95 15.5 5.89

A c e R o l l e r P u m p s

MODEL 661-CCAST IRON 6 ROLLER PUMP

Shaft 5/8" Stainless SteelPorts 3/4" NPT540 rpm 10 gpm max.

300 psi max.1000 rpm 17 gpm max.

300 psi max.

MODEL 881-CCAST IRON 8 ROLLER PUMP(shown with optional roller changeout plug)

Shaft 15/16" Stainless SteelPorts 3/4" NPT540 rpm 12 gpm max.

200 psi max.1000 rpm 22 gpm max.

300 psi max.

PART NO.

70103

PART NO.

70102

SEE NEXT PAGE FOR PARTS BREAKDOWN


A c e R o l l e r P u m p P a r t s

QTY. REQ.REF. PART NO. REPLACES DESCRIPTION 6 8

ROLLER ROLLER

6 71666 622-C End Plate 1

6 71667 882-C End Plate 1

*7 71066 6081 O-Ring 1

*7 71079 8081 O-Ring 1

8,9,11 71668 663-C-664 Rotor & Shaft Assy. 1

8,9,11 71669 883-C-884 Rotor & Shaft Assy. 1

*10 71068 10670 Roller, Nylon 6 8

*10 70820 10672 Roller, Polypropylene 6 8

12 71670 661C Housing 1

12 71671 881-C Housing 1

70628 25810 Repair Kit 6 Roller Super Rollers

70630 25910 Repair Kit 8 Roller Super Rollers

* in Repair KitCouplers See Page 96-99

QTY. REQ.REF. PART NO. REPLACES DESCRIPTION 6 8

ROLLER ROLLER

1 71620 41070 Retaining Ring 2

1 71663 811 Retaining Ring 2

2 71664 6610C Name Plate 1

2 71665 8810C Name Plate 1

*3 71023 BAC-37 Ball Bearing 2

*3 71032 10650 Ball Bearing 2

4 71022 6056 Seal Leather 2

4 71035 805L Seal Leather 2

*4 71021 605N Seal, Buna-N 2

*4 71034 805N Seal,Buna-N 2

4 71020 605V Seal Viton 2

4 71033 805V Seal Viton 2

5 71063 41330 Cap Screw 8 8

REF. PART NO. REPLACES DESCRIPTION QTY. REQ.1 1/2" 2"

1 71700 101.000.102 Seal, Buna 1 1

1* 71701 101.000.115 Seal, Viton 1 1

2 71702 104.000.142 Shim 1 1

3 None 106.000.102 Prime plug 1 -

3 None 106.000.104 Prime plug - 1

None 106.000.284 Drain plug 1 1

4* 71703 110.000.258 Shaft sleeve 1 1

None None O-Ring, shaft 1 1

5* 71704 116.000.146 O-Ring, casing 1 1

None None O-Ring, flange 1 1

6 71705 118.000.114 Flapper, Buna 1 -

6 71706 118.000.261 Flapper, EPDM 1 -

7 71707 119.000.206 Base Plate 1 1

8 71708 130.000.142 Casing 1 -

8 71709 130.000.239 Casing - 1

9 71710 131.000.238 Impeller 1 -

9 71714 131.000.526 Impeller - 1

10 71711 132.000.155 Adapter 1 1

11 71712 136.000.138 Flange, suction 1 -

None None Flange, discharge 1 1

12* 71713 104.000.179 Flinger 1 1

* 70700 118.000.252 Repair Kit

REPLACEMENT PARTS FOR SCOT CENTRIFUGAL PUMP

S c o t C e n t r i f u g a l P u m p

GASOLINE ENGINE MOUNTED



TRACTOR PTO DRIVENPART NO. REPLACES DESCRIPTION

70100 PTOC-600-10-6SP Cast iron 1 1/4" x 1" straight centrifugal with pulleys and 10 groove belt arranged for direct mountingon 1 3/8" 600 rpm PTO shaft. 0-60 psi. Equipped with 6 spline PTO drive shaft. Viton mechanical seal.Fully guarded for operator safety.

70101 PTOC-1000-10-21SP Cast iron 1 1/4" x 1" straight centrifugal with pulleys and 10 groove belt arranged for direct mountingon 1 3/8" 1000 rpm PTO shaft. 0-60 psi. Equipped with 21 spline split PTO drive shaft and split ringlocking collar. Viton mechanical seals. Fully guarded for operator safety.


REF. PART NO. REPLACES DESCRIPTION QTY.REQ.

1 71580 BAC-12 1 1/4" x 1" volute 12 71572 41110 1/8" NPT plug 33 71582 BAC-26-CI Impeller, cast iron 13 71583 BAC-26-VALOX Impeller, Valox 14 71584 BAC-7B Buna-N seal (optional) 14 71585 BAC-7V Viton seal (standard) 15 71586 BAC-4 Gasket, 4 hole 16 71587 40930 3/8" NC cap screw 47 71588 BAC-14MIA Mounting frame 18 71589 BAC-54 Slinger 19 71590 BAC-52 1/4" cold shut 1

10 71591 BAC-33 Internal snap ring (BAC-14) 211 71023 BAC-37 Ball bearing (BAC-6 shaft) 212 71593 BAC-32 Snap ring (BAC-6 shaft) 213 71594 BAC-5 Idler spring 114 71595 BAC-13 Idler arm 115 71596 BAC-36 External snap ring (BAC-13) 116 71645 BAC-28-8 8 groove belt (PTOC-600-10) 116 71597 BAC-28-10 10 groove belt 1

(PTOC-600-10, 600-10B)16 71598 BAC-28-10-M 10 groove belt 1

(PTOC-1000-10, 1000-10B)17 71599 BAC-29-10-1.5 10 groove pulley 1

1.7PD x 5/8” bore18 71600 BAC-6 5/8" shaft L.H. thread 118 71601 BAC-6-SS 5/8" S.S. shaft L.H. 119 71602 BAC-50 3/16" key 120 71603 BAC-57 5/16" NC set screw 121 71604 BAC-55 Idler bearing assy. 122 71605 BAC-47 Hex head idler cap screw 123 71606 BAC-30-10 10 groove pulley 10.6" PD x 2" 1

(PTOC-600-10)23 71607 BAC-30-10M 10 groove pulley 6.375" PD x 2" 1

(PTOC-1000-10)24 71608 BAC-10-6SPQC 1 3/8" 6 spline PTO (PTOC-600-10) 124 71609 BAC-10-21SP 1 3/8" 21 spline PTO (PTOC-1000-10) 124 71610 BAC-10-S 1" PTO stub drive shaft 1.25 71611 BAC-40 3/8" NC set screw 626 71612 40960 3/8" NC jam nut 627 71613 BAC-51 3/8" key 128 71614 BAC-34 Internal snap ring (BAC-15) 229 71615 BAC-31 Ball bearing for BAC-10 shaft 230 71616 BAC-38 Bearing spacer 131 71617 BAC-35 External snap ring (BAC-10) 133 71618 BAC-15 Bearing housing (PTOC-600, 1000) 133 71619 BAC-15-B Bearing housing w/base 600B 133 77801 BAC-15-A-6SP PTO drive shaft bearing 1

housing assy w/6 spline shaft37 71620 41070 Retainer ring 138 71621 BAC-46 5/8" jam nut spacer 1* 71622 40160 O-Ring for BAC-6 shaft 1* 71623 BAC-55-A Idler arm and outer roller assy. 1* 71624 BGKH Belt guard kit 1

* Does not appear in drawing


70672 RK-PTOC-600-10 Repair kit for PTOC-600-10-6SP, PTOC-600-10-QC, and PTOC-600-10B

70673 RK-PTOC-1000-10 Repair kit for PTOC-1000-10-21SP,and PTOC-1000-175-20SP

PART NO. REPLACES DESCRIPTION QTY

71597 BAC-28-10 10 groove belt (PTOC-600-10, 10B) 1

71598 BAC-28-10-M 10 groove belt (PTOC-1000-10, 10B) 1

71585 BAC-7V Viton seal 1

71586 BAC-4 Gasket, 4 hole 1

71622 40160 O -Ring for BAC-6 shaft 1

PTOC-600-10

harker

Cross-Out

harker

Typewritten Text

harker

Typewritten Text



PART NO. REPLACES

70104 PTOC-150-600-6sp

70105 PTOC-150-1000-21sp

70106 PTOC-150-600B with mounting base

70107 PTOC-150-1000B with mounting base

• The High Performance Pump. 40 GPM at 100 psi due toincreased pulley ratio and larger 1 1/2" x 1 1/4" construction

• Provides higher pressure and greater volume for applicationwith large tanks and long spray booms.

• Allow fuel savings by operating at lower engine speeds andstill maintains adequate spraying pressures

PTOC-150-600TRACTOR 450 500 540 600

PTO SPEED RPM RPM RPM RPMPSI GPM GPM GPM GPM

30 55 75 90 100

40 40 65 85 95

50 25 55 80 90

60 10 45 70 80

70 - 25 65 75

80 - 10 55 65

90 - - 30 55

100 - - - 40

PTOC-150-1000TRACTOR 700 800 900 1000

PTO SPEED RPM RPM RPM RPMPSI GPM GPM GPM GPM

30 85 90 93 100

40 74 87 90 95

50 67 80 87 90

60 44 74 80 85

70 - 63 72 78

80 - 43 65 72

90 - - 48 60

100 - - 15 40


70677 RK-PTOC-150-600 Repair kit for PTOC-150-600 series,includes belt 71659, seal 71585,and O-Ring 71652

70678 RK-PTOC-150-1000 Repair kit for PTOC-150-1000 series,includes belt 71672, seal 71585,and O-Ring 71652

1 1/2 X 1 1/4 CCW

SUCTION DISCHARGE

150 SERIESHIGH PERFORMANCE


P a r t s L i s t f o r P T O C - 1 5 0 - 1 0 0 0 - 2 1 S P & P T O C - 1 5 0 - 6 0 0 S P

REF PART NO. REPLACES REPLACES DESCRIPTION QTY.

# 71624 BGKH 052610 Belt and shaft guard (for PTO mounted centrifugal pumps) 11 71652 *BAC-4-150 40015 O-Ring, volute seal 12 71594 BAC-5 40030 Idler mounted torsion spring 13 71653 BAC-6-150/200 40055 5/8" driven shaft with keyway 14 71585 *BAC-7V 40151 Viton mechanical seal (includes 40160 O-Ring) 14 71584 BAC-7B 40110 Buna-N mechanical seal (includes 40160 O-Ring) (optional) 1# 71622 *40160 40160 O-ring for shaft 15 71654 BAC-10-6SP 40200 1 3/8" 6 tooth PTO spline drive shaft 16 71608 BAC-10-6SP-QC 40210 1 3/8" 6 tooth PTO spline shaft for quick coupler 17 71655 BAC-10-175-20SP 40180 1 3/4" 20 tooth PTO spline drive shaft, includes BAC-11-175 18 71609 BAC-10-21SP 40220 1 3/8" 21 tooth PTO spline drive shaft, includes BAC-11 19 71610 BAC-10-S 40190 1" tumblerod stub drive shaft 1

10 71656 BAC-11 40235 Split ring, locking collar (for BAC-10-21SP shaft) 113 71657 BAC-12-150 40255 Volute, 1 1/2" x 1 1/4" 114 71595 BAC-13 40270 Idler arm 116 71618 BAC-15 40340 PTO drive shaft bearing housing 1# 71619 BAC-15-B 40370 Tumblerod drive shaft bearing housing with mounting base 117 71658 BAC-26-150 40445 Impeller, cast iron with keyway 119 71659 *BAC-28-10-150 40611 Poly-v belt, 10 groove (for PTOC-150-600) 1# 71672 *BAC-28-10M-150 40621 Poly-v belt, 10 groove (for PTOC-150-1000) 120 71673 BAC-29-10-1.35 40675 1.35" P.D. x 5/8" bore poly-v pulley, 10 groove (for PTOC-150-600) 1# 71599 BAC-29-10-1.50 40680 1.5" P.D. x 5/8" bore poly-v pulley, 10 groove ( for PTOC-150-1000) 1

21A 71813 BAC-30-10-150 40741 11.6" PD x 2" bore poly-v pulley, 10 groove (PTOC-150-600) 121B 71814 BAC-30-175-150 40746 7.9" PD x 2 3/8" bore poly-v pulley for PTOC-150-1000-20SP 121B 71815 BAC-30-10M-150 40751 7.9" PD x 2" bore poly-v pulley (for PTOC-150-1000-21SP) 122 71615 BAC-31 40780 Sealed ball bearing, BAC-10 drive shaft 223 71593 BAC-32 40790 External snap ring for driven pump shaft 224 71625 BAC-32-S 40795 Spacer for pump shaft 125 71591 BAC-33 40810 Internal snap ring for mounting frame 226 71614 BAC-34 40830 Internal snap ring, BAC-15 bearing housing 227 71617 BAC-35 40840 External snap ring, BA-10 drive shaft 128 71596 BAC-36 40850 External snap ring, BAC-13 idler arm 129 71023 BAC-37 40870 Sealed ball bearing for pump shaft 230 71616 BAC-38 40900 Bearing spacer, drive shaft 131 71587 40930 40930 3/8" NC x 3/4" hex head cap screw, stainless steel (optional) 432 71611 BAC-40 40940 3/8" NC slotted set screw 333 71612 40960 40960 3/8" NC jam nut 338 71621 BAC-46 41020 5/8" spacer 139 71605 BAC-47 41040 5/8" NC x 2 1/8" hex head idler cap screw 140 71620 41070 41070 Retainer ring 141 71602 BAC-50 41080 3/16" x 3/16" x 1 1/4" key 142 71613 BAC-51 41090 3/8" x 1/2" x 1 1/2" key, PTO drive shaft 1# 71590 BAC-52 41100 1/4" cold shut, torque chain anchor 144 71572 41110 41110 1/8" NPT pipe plug 344 71573 41120 41120 1/8" NPT pipe plug, stainless steel (optional) 345 71589 BAC-54 41130 Slinger 146 71604 BAC-55 41140 Idler bearing and outer roller assembly 147 71603 BAC-57 41180 5/16" NC x 5/16"* allen head set screw for BAC-29-10 pulley 252 71807 BAC-81-QC 41450 Ball retainer sleeve 154 76519 BAC-83-QC 41470 Ball for quick coupler55 71683 BAC-14-150-MIA 40308 Mounting Frame.

* in seal kit

SEE NEXT PAGE FOREXPLODED VIEW.


PTOC-150-1000-21SP and PTOC-150-600SP



PART NO. REPLACES CLOSED CENTER OPEN CENTER PUMP ONLY

70200 FMC-HYD-204 All 4-13 gpm 70216

70201 FMC-HYD-210 Not recommended 14-17 gpm 70216

70202 FMC-HYD-310 Not recommended 18-24 gpm 70217



1 71586 BAC-4 Gasket, 4 hole 12 71626 BAC-6-HYD 5/8" driven shaft w/tang slot 12 71627 BAC-6-HYD-SS 5/8" driven shaft w/tang slot, 1

stainless2 71798 BACL-6-HYD-SS Shaft 5/8" w/tangss. for lipseal3 71584 BAC-7B Buna-N mechanical seal 13 71585 BAC-7V Viton mechanical seal 13 71796 40125 Leather seal 1# 71622 40160 O-Ring for BAC-6-HYD shaft 14 71580 BAC-12 1 1/4" x 1" volute 15 71628 BAC-14-HYD Mounting frame 15 71629 BAC-14-HYD-310 Mounting frame for BAC-75-HYD-310 1

hydraulic motor6 71630 BAC-23-SS 3/8" N.F. hex nut, stainless steel 17 71631 BAC-24-HYD-SS 3/8" washer, stainless steel 18 71632 BACH-25 1/8" x 1/8" x 1/2" impeller key 19 71633 BAC-26-HYD Impeller, Valox, w/keyway 19 71634 BAC-26-HYD-CI Impeller, cast iron, w/keyway(opt.) 110 71593 BAC-32 External snap ring, BAC-6-HYD 2

shaft11 71625 BAC-32S Spacer for BAC-6-HYD shaft 112 71591 BAC-33 Internal snap ring, 2

BAC-14-HYD frame13 71023 BAC-37 Sealed ball bearing, 2

BAC-6-HYD shaft14 71587 40930 3/8" N.C. x 3/4" hex head 4

cap screw15 71572 41110 1/8" NPT pipe plug 315 71573 41120 1/8" NPT pipe plug, 3

stainless steel16 71589 BAC-54 Slinger 117 71638 41256 5/16" N.C. x 3 1/2" hex head 4

cap screw motor to pump(FMC-HYD-204)

17 71639 41257 5/16" N.C. x 4" hex head cap 4screw motor to pump(FMC-HYD-210)

17 71640 41330 5/16" N.C. x 3/4" hex head cap 4screw motor to pump(FMC-HYD-310)

18 71641 BAC-75-HYD-204 Hydraulic motor (open or closed) 1center system with integralneedle valve) (FMC-HYD-204)

18 71642 BAC-75-HYD-210 Hydraulic motor (open or closed 1center system with integralneedle valve) (FMC-HYD-210)

18 71643 BAC-75-HYD-310 Hydraulic motor (open or closed 119 71644 BAC-76-HYD Coupling for hydraulic motor 1# 70984 40161 Steel Support spacer

#Not shown in cross section drawing

Cast iron 1 1/4" frame mounted straight centrifugal pump for tractor hydraulic system applications. Assembled with hydraulic motorequipped with internal check valve to prevent reverse rotation and resulting seal damage. Also equipped with integral needle valve tocontrol input of fluid on open center tractor hydraulic systems and a restrictor orifice to control input of fluid on closed center systemsis included with model FMC-HYD-204. (Models FMC-HYD-210 and FMC-HYD-310 are not equipped with restrictor orifice). To matchpump model with tractor hydraulic system capacity, refer to chart. Models FMC-HYD-204 and FMC-HYD-210 produce 0-100 psi atmaximum 4600 rpm and 60 gpm at open discharge. Model FMC-HYD-310 produces 0-65 psi at maximum 3950 rpm and 60 gpm atopen discharge. For open center systems which require sprayer pump pressures of from 60 to 100 psi, pump model FMC-HYD-210should be selected where the tractor system has a minimum of 8 gpm at 500 psi available at the remote ports.

Contact your WestwardParts order desk for more

information on selecting thecorrect centrifugal pump for

current model tractors.FMC-HYD-204

PUMP CAPACITIES (BASED ON WATER)10 PSI 30 PSI 40 PSI 50 PSI 60 PSI 90 PSI 100 PSI

MODEL GPM GPM GPM GPM GPM GPM GPM

204 75 60 - 50 - 20* 10*

210 75 60 - 50 - 20* 10*

310 75 60 50 - 20 - -

Data based on 1 foot lift through unrestricted suction hoseand fittings with full 1 1/4" I.D. on 1 1/4" x 1" series and 2" I.D.on 2" x 1 1/2" series. Performance based on maximum 4600rpm for 1 1/4" x 1" pumps equipped with 204 or 210 motors,and 3950 rpm for 1 1/4" x 1" pumps equipped with 310motors or all 2" x 1 1/2" pumps. * For open center systemswhich require sprayer pump pressures from 60 to 100 psi,pump model FMC-HYD-210 should be selected where thetractor has a minimum of 8 gpm at 500 psi available at theremote outlets.

REPAIR KITS FOR CENTRIFUGAL PUMP & ORBITMOTOR


70674 RK-FMC Pump seal kit for FMC-HYD-204,FMC-HYD-210, & FMC-HYD-310

70683 RK-FMCL Pump seal kit leather

70675 RK-BAC-75-204 Orbit motor repair kit (FMC-HYD-204,& FMC-HYD-210)

70689 RK-BAC-75-HYD-L New L seal kit for 71641 and71642 orbit motors

PART NO. REPLACES DESCRIPTION QTY.

71586 BAC-4 Gasket, 4 hole 1

71585 BAC-7V Viton mechanical seal 1

71622 40160 O-Ring for BAC-6-HYD shaft 1



REF. PART NO. REPLACES DESCRIPTION QTY

1 71586 BAC-4 Gasket, 4 hole 1

2 71626 BAC-6-HYD 5/8" driven shaft with tang slot 1

2 71627 BAC-6-HYD-SS 5/8" driven shaft with tang slot, 1stainless steel (optional)

3 71584 BAC-7B Buna-N mechanical seal 1(includes 40160 O-Ring) (optional)

3 71585 BAC-7V Viton mechanical seal 1(includes 40160 O-Ring)

3 71796 40125 Leather seal 1

4 71676 BAC-14-CCW Volute, 2" x 1 1/2" (for FMC-200 1and FMC-200-HYD)

# 71622 40160 O-ring for BAC-6 shaft 1

5 71628 BAC-14-HYD Mounting frame (for 1BAC-75-HYD-204 and 210hydraulic motors)

5 71629 BAC-14-HYD-310 Mounting frame (for 1BAC-75-HYD-310 hydraulic motor)

6 71630 BAC-23-SS 3/8" NF Hex nut, stainless steel 1

7 71631 BAC-24-HYD-SS 3/8" washer, stainless steel 1

8 71632 BACH-25 1/8" x 1/8" x 1/2" key 1

9 71675 41525 5 1/2" impeller cast iron, with keyway 1(for FMC-200-HYD)

10 71593 BAC-32 External snap ring, 2BAC-6 driven shaft

# 71625 BAC-32-S Spacer for BAC-6 shaft 1

11 71591 BAC-33 Internal snap ring, 2BAC-14 mounting frame

12 71023 BAC-37 Sealed ball bearing, 2BAC-6 driven shaft

13 71587 40930 3/8" NC x 3/4" hex head cap screw, 4stainless steel (optional)

14 71572 41110 1/8" NPT Pipe plug 3

14 71573 41120 1/8"* NPT pipe plug, stainless steel 3(optional)

15 71589 BAC-54 Slinger 1

16 71639 41257 5/16" NC x 4" hex head cap screw 4(for 210 motor)

# 71640 41330 5/16" NC x 3/4" cap screw 8BACH-12 volute

17 71642 BAC-75-HYD-210 8 GPM hydraulic motor for open- 1center or closed-center systemswith integral needle valve

17 71643 BAC-75-HYD-310 16 GPM hydraulic motor for 1open-center systems with integralneedle valve

18 71644 BAC-76-HYD Coupling for hydraulic motor 1

PART NO. MODEL NO. PUMP ONLY

SPP 70203 FMC-200-HYD-210 SPP 70218

SPP 70204 FMC-200-HYD-310 SPP 70219

• For high volume applications. Capacity to 180 GPM• Ideal for spraying, large tank agitation, liquid transfer, or

spray-transfer combinations• The 210 motor requires 8 GPM hydraulic input

Recommended for:- John Deere type pressure compensating closed centre systems- Case-IH type load sensing closed centre systems- Open centre systems with capacities from 8 to 17 GPM

• The 310 motor requires 16 GPM hydraulic fluid input.Recommended for large open centre systems with capacitiesfrom 16 to 24 GPM

SHUT-OFF 20 60 100 140 1800 GPM GPM GPM GPM GPM GPM

80 PSI 75 PSI 67 PSI 55 PSI 40 PSI 10 PSI

60 PSI 55 PSI 47 PSI 35 PSI 20 PSI

40 PSI 35 PSI 27 PSI 15 PSI

Maximum Pressure: 80 PSI (60 PSI for -310)Maximum Flow: 180 GPM

Note: To determine the correct performance data for yourapplication, first shut off all flow on discharge side of pump anddetermine the shut-off pressure at the pump. Use this SHUT-OFFpressure to determine which line of data applies.



70674 RK-FMC Pump seal kit Viton includes71586, 71585 & 71622

70683 RK-FMCL Pump seal kit leather includes71586, 71796 & 71622

70675 RK-BAC-75-204 Orbit motor repair kit(FMC-200-HYD-210)

70689 RK-BAC-75-HYD-L New L seal kit for71642 orbit motor

70676 RK-BAC-75-310 Orbit motor repair kit(FMC-200-HYD-310)

TRACTOR HYDRAULIC DRIVEN SYSTEM

2” X 1 1/2” CCWSUCTION DISCHARGE


Ace Hydraulic Driven Centrifugal Pump

REF. PART NO. REPLACES DESCRIPTION QTY.

*1 71652 BAC-4-150 O-Ring, volute 1

2 71626 BAC-6-HYD 5/8" driven shaft with tang slot 1

2 71627 BAC-6HYD-SS 5/8" driven shaft with tang slot, 1stainless steel (optional)

# 71584 BAC-7B Buna-N mechanical seal (optional) 1

*3 71585 BAC-7V Viton mechnical seal 1(includes 40160 O-Ring)

3 71921 BAC-7SC Silicon carbide Mechanical sealc/w 40160 o-ring. This materialis resistant to scratching byabrasive particles in spraysolution

*# 71622 40160 O-Ring for BAC-6-HYD shaft 1

4 71657 BAC-12-150 1 1/2" x 1 1/4" volute 1

5 71678 BAC-14-150-HYD Mounting frame 1

6 71630 BAC-23-SS 3/8" N.F. hex nut, stainless steel 1

7 71631 BAC-24-HYD-SS 3/8" lock washer, stainless steel 1

8 71632 BACH-25 1/8" x 1/2" x 1/2" impeller key 1

9 71658 BAC-26-150 Impeller, w/keyway cast iron 1

9 71916 BAC-26-150-P Impeller w/keyway plastic 1

10 71593 BAC-32 External snap ring, 2BAC-6-HYD driven shaft

11 71591 BAC-33 Internal snap ring, 2BAC-14-HYD-150 mounting frame

12 71023 BAC-37 Sealed ball bearing, 2BAC-6-HYD driven shaft

13 71587 40930 3/8" N.C. x 3/4" hex head cap screw, 4stainless steel (optional)

14 71572 41110 1/8" NPT pipe plug 3

14 71573 41120 1/8" NPT pipe plug, 3stainless steel (optional)


16 71679 41258 5/16" N.C. x 3 3/4" hex head cap screw 4motor to pump (for FMC-150-HYD-206)

17 71681 BAC-75-HYD-206 Hydraulic motor for open-centre or 1closed centre systems withintegral needle valve (for ModelFMC-150-HYD-206)

18 71644 BAC-76-HYD Coupling for hydraulic motor 1

19 71625 BAC-32-S Spacer for BAC-6 shaft 1

# 71808 LS-206 Flow limit valve for 71681 orbit motor 1

# 70984 40161 steel support spacer 1

* items included in repair kit# Not shown on cross section drawing



70679 RK-FMC-150 Pump seal kit, includes 71585, 71677and 71622

70675 RK-BAC-75-HYD Orbit motor repair kit(FMC-150-HYD-206

70689 RK-BAC-75-HYD-L New L seal kit for 71681 orbit motor

1 1/2” X 1 1/4” CCW

SUCTION DISCHARGE

PART NO. MODEL DESCRIPTION

SPP 70207 FMC-150-HYD-206 Hydraulic driven centrifugalpump

SPP 70231 Pump only

• The high performance pump - 20 GPM at 100 PSI• Provides higher pressure and greater volume for application

with large tanks and long booms• The 206 motor requires 7 GPM hydraulic fluid input and fits

virtually all tractor hydraulic systems• Recommended for:

- John Deere type pressure compensating closed centresystems- Case-IH type load sensing closed centre systems- Open centre systems with capacities from 7 to 16 GPM

SHUT-OFF 20 40 60 80 1000 GPM GPM GPM GPM GPM GPM





Maximum Pressure: 120 PSIMaximum Flow: 100 GPM

Note: To determine the correct performance data for yourapplication, first shut off all flow on discharge side of pump anddetermine the SHUT-OFF pressure at the pump. Use thisSHUT-OFF pressure to determine which line of data applies.

150 SERIES150 SERIES150 SERIES150 SERIES150 SERIESHIGH PERFORMANCE


Ac e H i g h C a p a c i t y H y d r a u l i c D r i v e n C e n t r i f u g a l Pu m p

• Suction 2" Discharge 1 1/2"• Recommended for use on the following Hydraulic Systems:

- Pressure Compensating Closed Centre- Load Sensing or Pressure Flow Compensating Closed Centre- Open Center from 10 to 20 GPM

• Integral Needle Valve bypasses up to 9 GPM on Open Center Systems• Standard Viton Carbon/Ceramic seal• All iron construction• Stainless Steel Shaft

PERFORMANCE CHARTSHUT-OFF 40 80 120 160 200

0 GPM GPM GPM GPM GPM GPM

120 psi 114 psi 100 psi 85 psi 65 psi 36 psi

100 psi 92 psi 83 psi 68 psi 52 psi -

80 psi 76 psi 68 psi 57 psi 43 psi -

60 psi 56 psi 50 psi 40 psi - -

Use the SHUT-OFF pressure of your spraying system to determinewhich line of data applies. The hydraulic system input pressure andflow will vary within the chart.MAXIMUM SHUT-OFF PRESSURE - 120 PSI

PART NO. MODEL NO.

SPP 70212 FMC-200-HYD-304SPP 70213 Pump Only

FOR PUMP PARTS BREAKDOWN SEE NEXT PAGE


A c e F M C - 2 0 0 - H Y D - 3 0 4

REF. # PART NO. REPLACES DESCRIPTION

1 71572 41110 Pipe plug

1 71573 41120 Pipe plug, stainless steel (optional)

2 71676 7AC-14-CCW Volute, 2" x 1-1/2

3 71918 BAC-23-A Nut, 3/8" NF, cad plated

4 71631 BAC-24-HYD-SS Washer, 3/8" star stainless steel

5 71919 BAC-26-200-CI Impeller, with extended keyway, cast iron (date code E-9 and up)

5 71675 BAC-26-HYD-200-CI Impeller, cast iron, keyway

5 70988 BAC-26-200P Impeller, thermoplastic

*6 71586 BAC-4 Gasket, 4 hole

*6 71920 BAC-4A O-Ring, body seal, effective April 1996

*7 71585 BAC-7V Seal, mechanical, Viton (includes 40160 O-Ring)

7 71921 BAC-7SC Seal, mechanical, silicon carbide (includes 40160 O-Ring (optional)

7A 71622 40160 O-Ring, shaft seal

8 71629 BAC-14-HYD-300 Mounting frame (for -300 series hydraulic motor)

10 71589 BAC-54 Slinger

11 71591 BAC-33 Snap ring, internal, BAC-14 mounting frame

12 71023 BAC-37 Ball Bearing, sealed, BAC-6 shaft

13 71593 BAC-32 Snap ring, external, BAC-6 shaft

14 71625 BAC-32-S Spacer for BAC-6 shaft

15 71922 BAC-25 Key, 1/8" x 1/8" x 13/16", extended keyway (date code E-9 and up)

15 71632 BACH-25 Key, 1/8" x 1/8" x 1/2"

16 71923 BAC-6-HYD-200-SS Shaft, extended keyway, tang, stainless steel (date code E-9 and up)

16 71626 BAC-6-HYD Shaft, 5/8" diameter, keyway and tang slot

16 71627 BAC-6-HYD-SS Shaft, 5/8" diameter, keyway and tang slot, stainless steel (optional)

16 71798 BACL-6-HYD-SS Shaft 5/8" w/tang slot SS for lipseal models

17 71644 BAC-76-HYD Coupling for hydraulic motor

18 71924 BAC-75-HYD-304 Hydraulic motor, 11 GPM

18 77817 BAC-75-HYD-307X Hydraulic Motor, 19 GPM

# 70674 RK-FMC Repair kit for FMC series pump

# 70728 RK-BAC-75-HYD-304 Repair kit for 304 motor

# 70729 RK-BAC-75-HYD-304-L Repair kit for 304-L motor

*Items included in pump repair kit.


REF NO. PART NO. MODEL 204 PART NO. MODEL 206 PART NO. MODEL 210 DESCRIPTION

1 71816 41720 71905 41721 71911 41725 Gear housing

2 71817 41731 71817 41731 71817 41731 Drive plate

3 71818 41740 71818 41740 71818 41740 End plate

4 71819 41750 71906 41751 71912 41755 Gear

5 71718 41761 71907 41764 71913 41766 Drive shaft

6 71719 41770 71719 41770 71719 41770 Steel seal retainer

6 78393 40153 78393 40153 78393 40153 Teflon Lip seal kit

7 71715 41780 71715 41780 71715 41780 Spring, reverse flow check

8 71716 41790 71716 41790 71716 41790 Valve cap, reverse flow check

9 71824 41800 71908 41805 71908 41805 Dowel pin, housing

10 71791 41810 71791 41810 71791 41810 Steel backup washer

11 71825 41820 71825 41820 71825 41820 Nylon washer

12 71792 41830 71792 41830 71792 41830 Wire ring bearing spacer

13 71793 41840 71793 41840 71793 41840 Collar, quad ring shaft seal

14* 71803 41850 71803 41850 71803 41850 O-Ring, housing seal

15* 71804 41860 71804 41860 71804 41860 O-Ring, seal retainer

16* 71805 41870 71805 41870 71805 41870 O-Ring, seal collar

17* 71806 41880 71806 41880 71806 41880 Quad ring shaft seal

18 71794 41890 71794 41890 71794 41890 Retaining ring, shaft seal

19 - 41900 - 41900 - 41905 Cap screw, 1/4" N.C. hex head

20 71826 41920 71909 41921 71914 41925 Pin, drive shaft

21 71827 41941 71827 41941 71827 41941 Snap ring, bearing

22 71717 41950 71717 41950 71717 41950 Ball, reverse flow check

23 71802 41961 71802 41961 71802 41961 Ball bearing 7/16" I.D.

24 71828 41970 71910 41971 71915 41975 Idler shaft

25 71809 41980 71809 41980 71809 41980 Retaining ring, idler gear

26 71829 41990 71829 41990 71829 41990 Ball, idler shaft

27 71801 42010 71801 42010 71801 42010 Adjusting screw, needle valve

28 - 40960 - 40960 - 40960 3/8" N.C. jam nut, needle valve

29* 71650 42030 71650 42030 71650 42030 3/8" thread seal, needle valve

30 71651 42040 71651 42040 71651 42040 Flat steel backup washer, needle valve

31 71810 42041 71810 42041 71810 42041 Valve cap, coasting check

32 71830 42042 71830 42042 71830 42042 Spring, coasting check

33 71811 42043 71811 42043 71811 42043 Ball, coasting check

34* 71812 42044 71812 42044 71812 42044 O-Ring, coasting check

70675 41371 70675 41371 70675 41371 Repair kit, RK-BAC-75-HYD

* Items included in repair kit

BAC-75-HYD-204, BAC-75-HYD-206, BAC-75-HYD-210

For motors with serial numbersbeginning with 40400

Ace Hydraulic Motor Parts List


Ref # Part No. Model 304 Part No. Model 310 Description Required1 77806 43175 77845 43170 Retaining ring, shaft seal 1

2 77807 43051 78415 43050 Steel seal retainer 12A 77844 40154 — — Hydraulic seal cartridge for -304L (replaces REF#2-7) 13 77846 43141 77847 43140 O-Ring, seal retainer 14 77848 43161 77849 43160 Quad ring shaft seal 15 77850 43125 77851 43120 Collar, quad ring shaft seal 16 77852 43151 77853 43150 O-Ring, seal collar 17 77854 43095 78417 43090 Backup washer 18 77855 43205 77856 43200 Retaining ring, bearing 29 77857 43225 77858 43220 Ball bearing 110 77859 43015 77860 43010 Drive plate 111 77861 43130 77861 43130 O-Ring, housing seal 212 77862 43085 77863 43080 Dowel pin, housing 213 77864 43005 77865 43000 Gear Housing 114 77865 43020 77866 43020 End plate 115 77867 43185 77868 43180 Cap screw, 3/8" N.C. hex head 416 77869 43210 77869 43210 Plunger, reverse flow check 117 77870 43060 77870 43060 Spring, reverse flow check 118 77871 43290 77871 43290 O-Ring, reverse flow check 119 77872 43070 77872 43070 Valve cap, reverse flow check 120 77873 43035 77874 43030 Gear 221 77875 43240 77875 43240 Retaining ring, gear 222 77876 43235 77877 43230 Idler shaft 123 77878 43255 77879 43250 Ball, idler shaft 124 77880 43195 77881 43190 Dowel pin, drive shaft 125 77810 43045 77882 43040 Drive shaft 126 77883 43270 77883 43270 Hex nut, needle valve 127 77884 43292 77884 43292 Flat steel backup washer, needle valve 128 70989 43291 70989 43291 ½" thread seal, needle valve 129 77885 43260 77885 43260 Adjusting screw, needle valve 130 77886 43300 — — Plunger, coasting check 131 77887 43305 — — Spring, coasting check 132 77888 43310 — — O-Ring, coasting check 133 77889 43315 — — Valve cap, coasting check 1

70728 041361 70676 041379 Motor repair kit, RK-BAC-75-HYD-304 or -310 —70729 041365 — — Motor repair kit, RK-BAC-75-HYD-304L —

BAC-75-HYD-304,BAC-75-HYD-304L, BAC-75-HYD-310

Ace Hydraulic Motor Parts List


A c e F l o w L i m i t e r V a l v e

FOR USE ON LOAD SENSING OR PRESSURE-FLOW COMPENSATING CLOSED CENTER SYSTEMS

MODEL LS• Installs in Ace Hydraulic Motor Inlet Port• Shuts off all hydraulic flow through valve when the motor’s capacity is exceeded• Protects Motor from overspeeding• Automatically resets when hydraulic pressure is released• Sizes available for all Ace models recommended for use on this hydraulic system

MODEL CHARTPUMP MODEL FLOW LIMITER PART NO.

FMC-HYD-204 LS204 71863

FMC-HYD-210 LS210 71864

FMC-150-HYD-206 LS206 71808

FMC-200-HYD-210 LS210-200 71864

FMC-HYD-304 LS304 71865

The flow limiter is a hydraulic device designed to shut off the flow of hydraulic oil when a specified flow is exceeded. On tractors withLOAD SENSING (LS) Closed Centre hydraulic systems, this device limits the flow of oil to the Ace motor and prevents failures due tomisapplication.The new Case-IH, John Deere, New Holland, and CAT tractors, present a great potential to turn the motors beyond their rated speeds.Flows out of the hydraulic valves can exceed 20 GPM while the motors are rated at 4-11 GPM. The flow limiter protects the ACE motorby shutting off when hydraulic flows exceed the motors capacity.The flow limiter should not be used on OPEN Center or PRESSURE COMPENSATING Closed Center hydraulic systems. The flow limitershould not be used with a restrictor orifice.

MOTOR MODEL “A”/”B” “L” “H”

200 Series 3/8" NPT 3 1/4" 7/8"

300 Series 1/2" NPT 3 5/16" 1 1/8"


Ace Frame Mounted Centrifugal Pumps

PRESSUREPUMP 20 40 60 80 100 120 140 160 MAXSHAFT PSI PSI PSI PSI PSI PSI PSI PSI HPSPEED GPM GPM GPM GPM GPM GPM GPM GPM

3200 RPM 55 30 - - - - - - 1.0

3800 RPM 63 50 20 - - - - - 1.7

4400 RPM 75 63 60 38 - - - - 3.0

5000 RPM 75 68 62 57 45 10 - - 4.2

6000 RPM 75 70 67 65 63 62 58 38 6.8

PART NO.

SPP 70205

PUMP REPAIR KIT

SPP 70674

PART NO.

SPP 70208

PUMP REPAIR KIT

SPP 70679


3200 RPM 77 45 - - - - - - 1.5

3800 RPM 96 80 38 - - - - - 4.0

4400 RPM 112 105 90 60 - - - - 6.0

5200 RPM 130 125 116 105 85 46 - - 10.0

6000 RPM 160 150 140 130 114 100 72 37 15.0

PART NO.

SPP 70206

PUMP REPAIR KIT

SPP 70674

PRESSUREPUMP 20 30 40 60 80 100 MAXSHAFT PSI PSI PSI PSI PSI PSI HPSPEED GPM GPM GPM GPM GPM GPM

2800 RPM 100 50 - - - - 1.7

3200 RPM 125 105 97 - - - 3.2

3600 RPM 140 130 121 - - - 4.0

4000 RPM 160 145 138 105 - - 5.3

4600 RPM 180 170 163 150 70 40 7.5

PUMP PARTS BREAKDOWN SEE NEXT PAGE

COUNTER CLOCKWISE ROTATION - CCW (WHEN FACING SHAFT)


A c e F M C a n d F M C - 2 0 0

1 1/4” X 1 2” X 1 1/2”FRAME MOUNTED CENTRIFUGAL PUMPS,COUNTERCLOCKWISE ROTATION

REQ.REF PART NO. REPLACES DESCRIPTION FMC FMC

-200

1 71586* BAC-4 Gasket, 4 hole 1 1

2 71600 BAC-6 5/8" driven shaft, left hand thread 1

2 71653 BAC-6-150/200 5/8" driven shaft with keyway 1

2 71601 BAC-6-SS 5/8" driven shaft, left hand thread,stainless steel (optional) 1

2 71797 BACL-6-SS 5/8" SS Shaft LH Thread for lip sealmodels

3 71584 BAC-7B Buna-N mechanical seal (includes40160 O-Ring) (optional) 1 1

3 71585* BAC-7V Viton mechanical seal (includes40160 O-Ring) 1 1

3 71921 BAC-7SC Silicon carbide mechanical 1 1seal c.w O-Ring. This materialis resistant to scratching byabrasive particles in spraysolution

# 71622* 40160 O-ring for BAC-6 shaft 1 1

5 71580 BAC-12 Volute, 1 1/4" x 1" 1

5 71676 7AC-14-CCW Volute, 2" x 1 1/2" (for FMC200 andFMC-200-HYD) 1

6 71682 BAC-14-MAG Mounting frame, machined toaccept magnetic clutch assembly 1 1

6 71588 BAC-14-MIA Mounting frame, machined foridler arm 1 1

7 71630 BAC-23-SS 3/8" NF hex nut, stainless steel 1


9 71632 BACH-25 1/8" x 1/8" x 1/2" key 1

10 71583 BAC-26-VALOX Impeller, Valox, left hand thread 1

10 71582 BAC-26-CI Impeller, cast iron, left handthread (optional) 1

10 71675 41525 5 1/2" Impeller cast iron, withkeyway (for FFMC-200-HYD) 1

11 71593 BAC-32 External snap ring, BAC-6driven shaft 2 2

12 71625 BAC-32-S Spacer for BAC-6 shaft 1 1

13 71591 BAC-33 Internal snap ring, BAC-14mounting frame 2 2

14 71023 BAC-37 Sealed ball bearing, BAC-6driven shaft 2 2

15 71587 40930 3/8" NC x 3/4" hex head capscrew stainless steel (optional) 4 4

16 71572 41110 1/8" NPT pipe plug 3 3

16 71573 41120 1/8" NPT pipe plug, stainlesssteel (optional) 3 3

17 71602 BAC-50 3/16" x 3/16" x 1 1/4" key 1 1

18 71589 BAC-54 Slinger 1 1

1 1/2” X 1 1/4”FRAME MOUNTED CENTRIFUGAL PUMPS,COUNTERCLOCKWISE ROTATIONREF PART NO. REPLACES DESCRIPTION REQ.

1 71652* BAC-4-150 O-Ring, volute seal 1

2 71653 BAC-6-150/200 5/8" driven shaft with keyway 1

3 71585* BAC-7V Viton mechanical seal (includes40160 O-Ring 1

# 71622* 40160 O-Ring for BAC-6 shaft 1

5 71657 BAC-12-150 Volute, 1 1/2" x 1 1/4" 1

6 71684 BAC-14-150-MAG Mounting frame, machined to acceptmagnetic clutch assembly 1

6 71683 BAC-14-150-MIA Mounting frame, machined foridler arm 1

7 71630 BAC-23-SS 3/8" NF hex nut, stainless steel 1


9 71632 BACH-25 1/8" x 1/8" x 1/2" key 1

10 71658 BAC-26-150 Impeller, Cast iron, with keyway 1

11 71593 BAC-32 Internal snap ring, BAC-6driven shaft 2

12 71625 BAC-32-S Spacer for BAC-6 driven shaft 1

13 71591 BAC-33 Internal snap ring, BAC-14mounting frame 2

14 71023 BAC-37 Sealed ball bearing, BAC-6driven shaft 2

15 71587 40930 3/8" NC x 3/4" hex head cap screw 4

16 71572 41110 1/8" NPT pipe plug 3

16 71573 41120 1/8" NPT pipe plug, stainlesssteel (optional) 3

17 71602 BAC-50 3/16" x 3/16" x 1 1/4" key 1


* Items included in repair kit# Not shown in exploded view drawing

ACE FMC AND FMC-200

FMC-150


Ace Frame Mounted Centrifugal Pumps

CLOCKWISE ROTATION-CW (WHEN FACING SHAFT)

FMC-CW-1501½" X 1¼"

SUCTION DISCHARGE5/8" SHAFT

FMC-CW-2002" X 1½"

SUCTION DISCHARGE5/8" SHAFT

FMC-CW-8002" X 1½"

SUCTION DISCHARGE

PUMP PARTS BREAKDOWN SEE NEXT PAGE

PART NO.

SPP 70209

PUMP REPAIR KIT

SPP 70674

PRESSUREPUMP 20 30 40 60 80 100 MAXSHAFT PSI PSI PSI PSI PSI PSI HPSPEED GPM GPM GPM GPM GPM GPM GPM

3200 RPM 70 55 5 - - - 1.4

3800 RPM 75 70 60 10 - - 1.8

4400 RPM 80 78 72 60 - - 3.0

5200 RPM 80 80 78 75 70 30 4.7

PART NO.

SPP 70214

PUMP REPAIR KIT

SPP 70674

PRESSUREPUMP 20 30 40 60 80 MAXSHAFT PSI PSI PSI PSI PSI HPSPEED GPM GPM GPM GPM GPM

2800 RPM 100 40 - - - 1.7

3200 RPM 125 100 90 - - 3.0

3600 RPM 140 125 110 - - 3.7

4000 RPM 160 140 135 90 - 4.5

4600 RPM 180 165 160 140 60 7.0

PART NO.

SPP 70215

PUMP REPAIR KIT

SPP 70682


3200 RPM 160 150 130 80 10 - - - 6.5

3600 RPM 180 180 150 120 60 40 - - 8.0

3800 RPM 180 180 175 150 120 80 30 - 10.0

4000 RPM 180 180 180 170 150 100 70 - 12.5

4200 RPM 180 180 180 180 170 140 100 50 14.2


Ace FMC-CW-150 and FMC-CW-200

1 1/2” X 1 1/4”2” X 1 1/2”

FRAME MOUNTED CENTRIFUGAL PUMPS,CLOCKWISE ROTATION

REQ.REF PART NO. REPLACES DESCRIPTION FMC FMC

-150 -200

1 71586* BAC-4 Gasket, 4 hole 1 1

2 71687 41480 5/8" driven shaft, R.H. thread 1 1

3 71685 6AC-12 Volute, 1 1/2" x 1 1/4",clockwise rotation 1 -

3 71686 7AC-14-4 Volute, 2" x 1 1/2",clockwise rotation - 1

4 71682 BAC-14-MAG Mounting frame, machined toaccept magnetic clutchassembly 1 1

4 71588 BAC-14-MIA Mounting frame, machinedfor idler arm 1 1

6 71584 BAC-7B Buna-N mechanical seal(includes 40160 O-Ring) 1 1(optional)

6 71585* BAC-7V Viton mechanical seal(includes 40160 O-Ring) 1 1

6 71921 BAC-7SC BAC-75C silicon carbide 1 1mechanical seal c/w O-Ring.This material is resistant toscratching by abrasive particlesin spray solution

7 71780 41510 Impeller valox, R.H. thread 1 -

7 71781 41515 Impeller, cast iron R.H. thread 1 -

7 71782 41520 Impeller, cast iron R.H. thread - 1

8 71572 41110 1/8" NPT pipe plug 3 3

8 71573 41120 1/8" NPT pipe plug, stainlesssteel (optional) 3 3

9 71589 BAC-54 Slinger 1 1

10 71593 BAC-32 External snap ring,BAC-6 driven shaft 2 2

11 71591 BAC-33 Internal snap ring,BAC-14 mounting frame 2 2

15 71622* 40160 O-Ring for BAC-6 shaft 1 1

17 71602 BAC-50 3/16" x 3/16" x 1 1/4" key 1 1

18 71625 BAC-32-S Spacer for BAC-6 shaft 1 1

19 71587 40930 3/8" NC x 3/4 hex head capscrew, stainless steel 4 4(optional)

# 71023 BAC-37 Sealed ball bearing,BAC-6 driven shaft 2 2

2” X 1 1/2”

FRAME MOUNTED CENTRIFUGAL PUMPS,CLOCKWISE ROTATIONREF PART NO. REPLACES DESCRIPTION REQ.

1 71694* 9000 Gasket, 8 hole 1

2 71688 ALCAL-6 Shaft, stainless steel(for FMC-CW-800) 1

3 71689 ACAL-14 Volute, 2" x 1 1/2",clockwise rotation 1

4 71690 ACAL-15 Mounting frame 1

5 71032 10650 Ball bearing, sealed 2

6 71692* 30255 .984" Viton mechanical seal 1

7 71693 ACAL-26-75 Impeller, 8" diameter, with keyway 1

8 71572 41110 1/8" NPT pipe plug 3

8 71573 41120 1/8" NPT pipe plug, stainlesssteel (optional) 3

9 71574 GE-54 Slinger 1

10 71696 BACG-32 External snap ring, BACG-6-SS-Adriven pinion shaft 2

11 71697 BACG-33 Internal snap ring, BACG-14-Amounting frame 2

14 71698 BACG-90M Seal cartridge for mechanical seal 1

15 71699* 13300-90 O-Ring 2

16 71695 41079 3/16" x 3/16" x 1/2" impeller key 2

17 71602 BAC-50 3/16" x 3/16" key 1

18 71691 ACAL-32-S Bearing spacer for ACAL-6 shaft 1

19 71587 40930 3/8" NC x 3/4" hex head cap screw 8

* Items included in repair kit# Not shown in exploded view drawing

FMC-CW-800


Ace Magnetic Clutch Centrifugal Pumps

COUNTERCLOCKWISE ROTATION-CCW (WHEN FACING SHAFT)

PART NO.

SPP 70232

PUMP REPAIR KIT

SPP 70674


3200 RPM 55 30 - - - - 1.0

3800 RPM 63 50 20 - - - 1.7

4400 RPM 75 63 60 38 - - 3.0

5200 RPM 75 70 65 61 50 15 4.2

PART NO.

SPP 70233

PUMP REPAIR KIT

SPP 70679


3200 RPM 77 45 - - - - 1.5

3800 RPM 96 80 38 - - - 4.0

4400 RPM 112 150 60 60 - - 6.0

5200 RPM 130 125 116 105 85 46 10.0

PART NO.

SPP 70234

PUMP REPAIR KIT

SPP 70674


3200 RPM 125 105 97 - - - 3.2

3600 RPM 140 130 121 - - - 4.0

4000 RPM 160 145 138 105 - - 5.3

4600 RPM 180 170 163 150 70 40 7.5

MAGNETIC CLUTCH PARTS FOR FMC, FMC-150 AND FMC-200 MODELSPART NO. REPLACES DESCRIPTION REQ.

71783 41475 Magnetic clutch assembly, rated at 13 ft/lbs and 10 h.p. at 4000 RPM (standard clutch) 1

71784 41476 Coil ring, 12 volt DC activated (for standard clutch) 1

71785 41477 Spacer, (for standard clutch) 1

PUMP PARTS BREAKDOWN SEE PAGE 1-38

FMC-MAG1 1/4” X 1”SUCTION DISCHARGE

FMC-150-MAG1 ½” X 1¼”SUCTION DISCHARGE

FMC-200-MAG2” X 1½”SUCTION DISCHARGE



PART NO.

SPP 70235

PUMP REPAIR KIT

SPP 70674


3200 RPM 70 55 5 - - - 1.4

3800 RPM 75 71 60 10 - - 1.8

4400 RPM 80 78 72 60 - - 3.0

5200 RPM 80 80 78 75 70 30 4.7

PART NO.

SPP 70236

PUMP REPAIR KIT

SPP 70674


2800 RPM 100 40 - - - - 1.7

3200 RPM 125 100 90 - - - 3.0

3600 RPM 140 125 110 - - - 3.7

4000 RPM 160 140 135 90 - - 4.5

4600 RPM 180 165 160 140 60 - 7.0

FMC-CW-800-MAG

2” X 1 1/2”SUCTION DISCHARGE

PART NO.

SPP 70237

PUMP REPAIR KIT

SPP 70682


3200 RPM 160 150 130 80 10 - - - 6.5

3600 RPM 180 180 150 120 60 40 - - 8.0

3800 RPM 180 180 175 150 120 80 30 - 10.0

4000 RPM 180 180 180 170 150 100 70 - 12.5

4200 RPM 180 180 180 180 170 140 100 50 14.2

FMC-CW-200-MAG

2” X 1 1/2”SUCTION DISCHARGE

FMC-CW-150-MAG

1½” X 1 1/¼”SUCTION DISCHARGE

MAGNETIC CLUTCH PARTS FOR FMC-CW-800-MAGPART NO. REPLACES DESCRIPTION REQ.

71786 41479 5 1/4" pulley assembly complete with bearing and clutch driver (for standard clutch) 1

71787 41485 Magnetic clutch assembly, rated for 30 ft/lb torque and 23 HP at 4000 rpm (for use with FMC-CW-800-MAG) 1

71788 41486 5" pulley assembly complete with bearing and clutch driver (for use with FMC-CW-800-MAG) 1

71789 41487 Coil ring, 12 volt DC activated (for use with the FMC-CW-800-MAG) 1

71790 41489 Spacer, (for use with the FMC-CW-800-MAG) 1

CLOCKWISE ROTATION-CW (WHEN FACING SHAFT)

Equipped with heavy duty magnetic clutch whichdraws 2 amps and is capable of transmitting 23HP at 4,000 RPM.

PUMP PARTS BREAKDOWN SEE PAGE 1-40



D e l a v a n C e n t r i f u g a l P u m p

Features: Common shaft eliminates the need for external couplings or bearing. Viton pump sealsare standard. Nylon impeller reduces wear and resists corrosion. Compact size allows for a rangeof installation points. Delavan centrifugal pumps use high quality Gresen motors. The hydraulicmotors can be adapted to operate on either “open-center” or “closed-center” tractor hydraulicsystems. Pump assembly #34945 (with #35277 metering orifice installed in the inlet port of themotor) can be used on a closed-center hydraulic system. All models can be used on open-centerhydraulic systems. For pump/motor #34945-1, a minimum of 4 gpm and a maximum of 12 gpm ofhydraulic fluid input at 1260 psi is required for the pump to operate at rated capacity. For pump/motor #35566-1, a minimum of 11 gpm and a maximum of 18 gpm at 600 psi is required. Forpump/motor #46818-1, a minimum of 17 gpm and a maximum of 24 gpm at 600 psi is required.

PUMP CAPACITIES (BASED ON WATER)20 PSI 40 PSI 60 PSI

MODEL GPM GPM GPM

34945 51 37 24

35566 59 47 29

Contact your Westward Parts order desk for more information onselecting the correct centrifugal pump for current model tractors.

PART NO. REPLACES HYDRAULIC OIL FLOW TRACTOR HYDRAULIC SYSTEM

70210 34945-1 15-45 L/min @ 8600 kPa Closed &4-12 gpm @ 1250 psi Open

70211 35566-1 42-68 L/min @ 4100 kPa Open11-18 gpm @ 600 psi

REPLACEMENT PARTS FOR CENTRIFUGAL PUMP

REPAIR KIT FOR CENTRIFUGAL PUMP & ORBITMOTOR


70608 35745 Pump repair kit

70609 38109-1 Orbit bearing and seal kit (Gresen)

70610 38109-2 Orbit seal kit (Gresen motor)

70611 38109-3 Orbit check valve kit (Gresen motor)

70612 38109-4 Orbit bypass valve kit (Gresen motor)

70618 36634 External bypass kit


70865 34912 Pump gasket 1

70866 34944 Cap locknut 1

70867 34942 Washer 1

70870 34943 Face seal assembly 1

70873 35278 Gasket slinger 1


1 70862 34907 Volute casing 1

4 70865 34912 Pump gasket 1

5 70866 34944 Cap locknut 1

6 70867 34942 Washer 1

7 70868 34915-2 Impeller assembly 1

8 70869 34941 Impeller key 1

9 70870 34943 Face seal assembly 1

10 70871 34908 Mounting support 1

11 70872 34916 Cap screw 6

12 70873 35278 Gasket slinger 1

13 70874 35312 Adapter 1

14 70875 31351-15 O-Ring 2

15 70876 35564-1 Hydraulic motor - 34945-1 assy. 1

15 70877 35564-2 Hydraulic motor - 35566-1 assy. 1

15A 70878 35277-P Metering orifice (34945-1 only) 1

17 70880 35776 Adapter 1

TRACTOR HYDRAULIC SYSTEM DRIVEN


H y p r o C e n t r i f u g a l P u m p

REPLACEMENT PARTS FOR CENTRIFUGAL PUMP

QTY.REF. PART NO. REPLACES DESCRIPTION REQ.

1 71176 2406-0007 Drain/vent plug 41 71177 2406-0016 Drain/vent plug (for Valox) 42 71178 0150-9000C Pump casing (volute) 12 71234 0150-9200C Pump casing (volute)fits 93043 71179 2253-0002 Impeller nut 13 71180 2253-0006 Impeller nut (for Valox) 14 71181 0402-9100P Impeller (polypropylene)fits 9303 14 71380 0401-9100P Impeller (nyglass std.) fits 93034 70990 0401-9200C Cast iron Impeller Fits 93045 71182 2120-0009 Mechanical seal Viton 9303 Model 15 71235 2120-0008 Mechanical seal Buna-N 9301 Models6 71236 1720-0083 O-Ring 17 71184 2210-0020 Hex head capscrew 48 71185 0750-9300C Mounting flange 111 71186 1410-0056 Slinger ring 112 71187 1820-0013 Retaining ring 113 71188 1810-0014 Snap ring 114 71023 2000-0010 Ball bearing 115 71190 1410-0073 Spacer 116 71191 2104-0005 Shaft seal 117 71192 1410-0074 Seal spacer 118 71193 2029-0014 Thrust bearing assy (w/2 races) 119 71194 1810-0026 Snap ring 120 71195 0509-2500 Shaft (HM2 - HM4 models) 120 71196 0511-2500 Shaft (HM1 models)and HMS 120 71197 0510-2500 Shaft (HM3 models) 121 71198 1610-0012 Woodruff key 122 71199 1610-0032 Roll pin (HM2 & HM4 models) 123 71200 0151-2500A Front motor body (w/main bearing) 124 71036 2210-0005 Hex head capscrew 425 71201 1720-0110 O-Ring 226 71202 07012500A Gerotor housing (HM2 models) 126 71203 0700-2500A Gerotor housing (HM1 models) 126 71204 0703-2500A Gerotor housing (HM4 models) 126 71205 0702-2500A Gerotor housing (HM3 models) 126 71714 0704-2500C Gerotor Housing (HM5C)27 71206 1600-0045 Dowel pin (HM2 & HM4 models) 127 71207 1600-0044 Dowel pin (HM1 & HM5 models) 127 71208 1600-0052 Dowel pin (HM3 models) 128 71209 1600-0042 Dowel pin (HM2 & HM4 models) 128 71210 1600-0037 Dowel pin (HM1 & HM5 models) 128 71211 1600-0051 Dowel pin (HM3 models) 129 71212 3900-0023 Gerotor (HM2 models) 129 71213 3900-0022 Gerotor (HM1 models) 129 71214 3900-0025 Gerotor (HM4 models) 129 71215 3900-0024 Gerotor (HM3 models) 129 77809 3900-0048 Gerotor (HM5C)30 71216 0251-2500A Motor end plate (w/main bearing) 131 71217 3220-0029 Bypass adjusting screw 132 71218 1700-0047 Gasket 133 71219 2270-0027 Washer 134 71220 2250-0038 Lock nut 135 71221 2270-0039 Washer 436 71222 2220-0045 Capscrew (HM2 & HM4 models) 436 71223 2220-0021 Capscrew (HM1 models) 436 71224 2220-0044 Capscrew (HM3 models) 437 71225 1720-0108 O-Ring 238 71226 3320-0016 Tank port adapter 139 71227 3260-0039 Poppet 140 71228 1820-0023 Retaining ring 141 71229 3320-0015 Tank check valve assembly 1

(includes O-Ring, tank port, adapterpoppet, retaining ring)

42 71230 3360-0021 Pressure port adapter 143 71231 1720-0105 Orifice O-Ring (HM2 & HM4 models) 144 71232 3373-0020 Metering orifice (HM2 & HM4 models) 1

TRACTOR HYDRAULIC SYSTEM DRIVENMounting almost anywhere on tractor or sprayer, series 9300 be-comes part of the vehicle’s hydraulic system and frees the PTO forother uses. “Close-coupled” design reduces mounting space – asingle stainless steel shaft is common to both pump and motor.Pump construction: Epoxy-coated cast iron housing, nylon impeller,two needle main bearings and an outboard, double sealed factory-lubricated ball bearing. Viton sealing element standard.

CLOSED OPEN HYDRAULIC MOTORPART NO. REPLACES CENTER CENTER PART NO REPLACES

70224 9304C-HM5C Yes Yes 70929 2500-0018C

70275 9304C-HM1C Yes Yes 71439 2500-0009C

70276 9304C-HM3C No Yes 71441 2500-0011C

Port Size: 2" inlet, 1 1/2" outletWeight: 21 lbs.

CLOSED OPEN HYDRAULIC MOTORPART NO. REPLACES CENTER CENTER PART NO REPLACES

70220 9303C-HM1C No Yes 71439 2500-0009C

70221 9303C-HM2C Yes No 71440 2500-0010C

70222 9303C-HM3C No Yes 71441 2500-0011C

70223 9303C-HM4C Yes No 71442 2500-0012C

70272 9303C-HM5C Yes Yes 70929 2500-0018C

Port Size: 1 1/2" inlet, 1 1/4" outletWeight: 21 lbs.

REPAIR KITS FOR ORBIT MOTORPART NO. REPLACES DESCRIPTION

70639 3430-0178 Parts repair kit HM1, HM2, HM3,HM4,HM5Parts kit contains: one each ballbearing (ref. 14), motor shaft seal(ref.16) thread seal gasket (ref.32) andwasher (ref. 33), two each motorhousing O-Rings (ref. 25) and portadapter O-Rings (ref. 37)

70640 3430-0187 Adapter kit for HM4 models onlyAdapter kit includes: one each ref. 37,ref 42 and ref. 44, and three of ref. 43

9303C-HM1: Output to 120 gpm - pressure to 180 psi - 10 gpm hyd. motor9303C-HM2: Output to 95 gpm - pressure to 100 psi - 5 gpm hyd. motor9303C-HM3: Output to 120 gpm - pressure to 100 psi - 20 gpm hyd. motor9303C-HM4: Output to 110 gpm - pressure to 100 psi - 7 gpm hyd. motor9303C-HM5C: Output to 147 gpm-pressure to 145 psi-15 gpm hyd motor9304C-HM1C: Output to 210 gpm -pressure to 115 psi - 10 gpm hyd motor9304C HM3C: Output to 190 gpm - pressure to 80 psi- 20 gpm hyd motor9304C-HM5: Output to 200 gpm - pressure to 90 psi - 15 gpm hyd motor


70641 3430-0332 Repair kit (Viton seal and O-Ring)

70642 5168248 Repair kit (Buna-N seal and O-Ring)


71182 2120-0009 Mechanical seal (viton) standard 1

71235 2120-0008 Mechanical seal (Buna-N) opt. 1

71236 1720-0083 O-Ring (Buna-N)

77715 3430-0475 Silicon seal and O-Ring

Contact your Westward Parts order desk for more informationon selecting the correct centrifugal pump for current modeltractors.


MAX. MAX.PART NO. REPLACES GPM PSI DESCRIPTION

70337 9302C-HM1C 72 140 11 gpm hydraulic motor/cast iron pump, open/closed center systemsports 1¼" inlet 1" outlet

70338 9302C-HM2C 65 90 4 gpm hydraulic motor/cast iron pump, open/closed center systemsports 1¼" inlet 1" outlet

70339 9302C-HM4C 72 110 6 gpm hydraulic motor/cast iron pump, open/closed center systemsports 1¼" Inlet 1" outlet

H y p r o C e n t r i f u g a l P u m p s

HYDRAULIC DRIVEN, STAINLESS STEEL Features:• Hydraulic motor drive (for open and closed center systems)• Maximum flow: 82-190 gpm• Maximum pressure: 130-180 psi (in closed center operation)• Maximum fluid temperature: 140°F• Port sizes:

9303S 1.5" NPT inlet1.25" NPT outlet

9306S 2" NPT inlet1.5" NPT outlet

• Housing: Stainless Steel• Impeller:

9303S series: poly9306S series: glass-filled nylon

• Motor: Internal gear gerotor• Hydraulic ports: .5" NPT• Motor capacities: 5-20 gpm• Weight: 21 lbs/9.52 kg• Centrifugal shaft seals: Viton/ceramic• Hydraulic motor seal, double lip teflon

These new Stainless Steel pumps from Hypro Corporation are justwhat you need for effectively handling caustic chemicals. TheS-series pump is ideal for use with Roundup® or other acidapplications, such as burndown and defoliation.


70225 9303S-HM1C 114 130 10 gpm hydraulic motor/stainless steel pump for open/closed center systems1 1/2" NPT inlet, 1 1/4" NPT outlet

70226 9303S-HM4C 115 93 7 gpm hydraulic motor/stainless steel pump for open/closed center systems1 1/2" NPT inlet, 1 1/4" NPT outlet

70227 9306S-HM1C 210 115 10 gpm hydraulic motor/stainless steel pump for open/closed center systems2" NPT inlet, 1 1/2" NPT outlet

70228 9306S-HM5C 210 95 15 gpm hydraulic motor/stainless steel pump for open/closed center systems2" NPT inlet, 1 1/2" NPT outlet


70329 9305C-HM3C 190 180 20 gpm hydraulic motor/cast iron pump, large open center systems, ports(NPT): 2" inlet, 1½" outlet

70330 9306C-HM1C 207 130 10 gpm hydraulic motor/cast iron pump, open/closed center systems, ports(NPT): 2" inlet, 1½" outlet.

70331 9306C-HM3C 214 135 20 gpm hydraulic motor/cast iron pump, open/closed center systems,ports(NPT): 2" inlet, 1½" outlet

70332 9306C-HM5C 212 150 15 gpm hydraulic motor/cast iron pump, large open center systems, ports(NPT): 2" inlet, 1½" outlet

77715 3430-0475 Silicon Seal and O-Ring

77716 3430-0551 Silicon Seal for 9305C-HM3C only

SERIES 9300 CAST IRON, HYDRAULIC DRIVEN PUMPS

SERIES 9302 CAST IRON, HYDRAULIC DRIVEN PUMPS


Hypro Polypropylene Centrifugal Pumps

HYDRAULIC MOTOR DRIVENMAX MAX HYD MOTOR

PART NO. MODEL NO. GPM PSI SYSTEM DESCRIPTION PART NO.

70080 9303P-HM1C 90 100 Open/closed The hydraulic motor features a fixed displacement internal gear design 7143970081 9303P-HM3C 93 100 Open for smooth operation. A double lip teflon shaft seal provides excellent 7144370082 9303P-HM4C 86 100 Open/closed reliability even with high hydraulic oil back pressure. The hardest 71444

stainless steel motor/pump shaft is supported by two needle bearingsand a ball bearing for dependable operation through years of use.

Ports: 1 1/2" NPT Inlet1 1/4" NPT Outlet

Hydraulic Ports: 1/2" NPT Inlet1/2" NPT Tank

PART NO DESCRIPTION

70639 Orbit motor repair kit

Parts kit No. 3430-0178 Contains: One each ball bearing (Ref. 14), motor shaft seal(Ref. 16), thread seal gasket (Ref. 32), and washer (Ref. 33), two each motor hous-ing O-Rings (Ref. 25), and port adapter O-Rings (Ref. 37)

REPAIR KITPART NO. REPLACES DESCRIPTION

70727 3430-0445 Contains one of ref.2, 3, 55, 56 and 57

77715 3430-0475 Silicon Seal & O-Ring

PART QTY.REF. NO. REQ. REPLACES DESCRIPTION

1 71445 1 1410-0082 Spacer

2 71182 1 2120-0009 Mechanical seal

3 71446 1 1721-0083 O-ring

4 71447 4 2406-0020 Pipe plug

5 71448 1 2250-0051 Jam nut

6 71449 1 2250-0052 Impeller nut

7 71450 1 0700-9000P Pump casing

8 71451 1 2210-0088 Screw

9 71181 1 0402-9100P Impeller

10 71452 4 2210-0087 Hex head capscrew

11 71186 1 1410-0056 Slinger ring

12 71187 1 1820-0013 Retaining ring

13 71188 1 1810-0014 Snap ring

14 71023 1 2000-0010 Ball bearing

15 71190 1 1410-0073 Spacer

16 71191 1 2104-0005 Shaft seal

17 71192 1 1410-0074 Seal spacer

18 71193 1 2029-0014 Thrust bearingassembly: Includes (1)Thrust bearing (2)Thrust bearing races

19 71194 1 1810-0026 Snap ring

20 71453 1 0507-2500 Shaft HM4, 7 1/16” long

20 71454 1 0508-2500 Shaft HM3, 7 13/16” long

20 71455 1 0506-2500 Shaft HM1, 7 5/16” long

21 71198 1 1610-0012 Woodruff key

22 71199 1 1610-0032 Roll pin (HM4 Model)

22 71456 1 1610-0030 Woodruff key (HM3Model)

22 71457 1 1610-0031 Roll pin (HM4 model)

23 71200 1 0151-2500A Front motor body:Includes (1) Main brg.

25 71201 2 1720-0110 O-ring

26 71203 1 0700-2500A Gerotor housing (HM1Model) ½” wide

26 71204 1 0703/2500A Gerotor housing (HM4Model) 5/16” wide

26 71205 1 0702-2500A Gerotor housing (HM3Model) 1” wide

27 71206 1 1600-0045 Dowel pin (HM4model)

27 71208 1 1600-0052 Dowel pin (HM3model)


27 71207 1 1600-0044 Dowel pin (HM1 model)




29 71214 1 3900-0025 Gerotor (HM4 model)

29 71215 1 3900-0024 Gerotor (HM3 model)

29 71213 1 3900-0022 Gerotor (HM1 model)

30 71216 1 0251-2500A Motor end plate: Incl.

(1) main bearing

31 71217 1 3220-0029 Valve stem

32 71218 1 1700-0047 Gasket

33 71219 1 2270-0027 Washer

34 71220 1 2250-0038 Lock nut

35 71221 4 2270-0039 Washer

36 71222 4 2220-0045 Socket head capscrew

(HM4 models)


(HM3 models)


(HM1 model)

37 71225 2 1720-0108 O-ring

38 71226 1 3320-0016 Check valve body

39 71227 1 3260-0039 Poppet


40 71228 1 1820-0023 Retaining ring

41 71229 1 3320-0015 Tank check valve assy.

Consists of: (1) O-Ring -

ref. 37, (1) check valve

Body - ref 38, (1)

Poppet - ref 39, (1)

Retaining ring - Ref 40

42 71230 1 3360-0021 Pressure port adapter

43 71231 1 1720-0105 Orifice O-Ring (HM4

models only)

44 71232 1 3373-0020 Metering orifice (HM4

models only)

45 71458 6 2270-0041 Washer

46 71459 1 0750-9300P Cover

47 71460 1 0750-9006C Intermediate flange

48 71461 4 2260-0002 Lockwasher


52 71463 2 2210-0016 Screw

53 71464 6 2250-0008 Hex nut

54 71465 1 1510-0063 Mounting foot

55 71466 1 2270-0057 Washer

56 71467 1 1700-0097 Gasket

57 71468 1 1700-0100 Rubber gasket


H y p r o C e n t r i f u g a l P u m p

Two models with different capacities (130 gpm and 105 gpm), bothmodels with the volume and pressure to handle many spraying ap-plications and liquid transfers. Pumps offer great installationversatility. The pedestal mounting base can be used for direct driveor belt and pulley drive. The pump outlet can be rotated to fourdifferent positions.Ports:Model 9202C: Inlet 1 1/4" NPT, Outlet 1" NPTModel 9203C: Inlet 1 1/2" NPT, Outlet 1 1/4" NPT

Model 9204C and 9205C: Inlet 2" NPT, Outlet 1 1/2" NPTShaft: 5/8" solid stainless steel with 3/32" x 3/16" keywayShaft Seal: Stainless steel mechanical seal of ceramic and carbonfaces with Viton sealing element. Buna-N seal is available.Outlet: Can be changed to four different positions by removingthe bolts and rotating the casing.Housing: Pressure tested cast iron. Epoxy coated inside and out.Mounting flange is drilled to accept two 3/8" bolts.Bearings: Two heavy-duty, factory lubricated shaft ball bearings.Net Weight: 15 1/2 pounds (7.03 kg).PSI: 180Output to 130 gpm: pressure to 180 psiSpeed to 6000 rpm: temperature to 140°F

PART NO REPLACES DESCRIPTION

70066 9202C Pump w/ 5/8" shaft

70067 9203C Pump w/ 5/8" shaft

70083 9203C-R Pump w/ 5/8" shaft clockwise rotation

70127 9204C Pump w/ 5/8" shaft

70128 9205C Pump w/7/8" shaft

REPAIR PARTSREF. PART NO. REPLACES DESCRIPTION QTY.

1 71233 2406-0009 Drain vent plug 4

2 71234 0150-9200C Pump casing (9202) 1(1 1/4" inlet, 1” outlet)

2 71178 0150-9000C Pump casing (9203) 1(1 1/2" inlet, 1 1/4" outlet

2 71470 0152-9000C Pump casing (9203-R) 1

3 71179 2253-0002 Impeller nut 1

4 71380 0401-9100P Impeller (9202 & 9203)9262 1

4 71469 0403-9100P Impeller (9203-R)9263 1

5 71236 1720-0083 O-Ring (Buna-N) 1

6 71182 2120-0009 Mechanical seal (Viton) standard 1

6 71235 2120-0008 Mechanical seal (Buna-N) opt. 1

6 71482 2120-0032 Mechanical seal silicon 1

7 71237 1830-0040 Seal retainer 1

8 71186 1410-0056 Slinger ring 1

11 71184 2210-0020 Bolt 4

12 71023 2000-0004 Ball bearing 2

13 71240 1610-0015 Key 1

14 71241 0501-9200 Pump shaft 1

15 71242 1610-0004 Key 1

16 71187 1820-0013 Bearing retainer ring 1

REPAIR KITSPART NO. REPLACES DESCRIPTION

70641 3430-0332 Repair kit (Viton seal and O-Ring)

70642 5168248 Repair kit (Buna-N seal and O-Ring)

77715 3430-0475 Silicone Carbide Kit


71182 2120-0009 Mechanical seal (viton) standard 1

71235 2120-0008 Mechanical seal (Buna-N) opt. 1

71236 1720-0083 O-Ring (Buna-N) 1

SERIES 9200 PEDESTAL MODELS WITH 12-VOLT CLUTCHES

PART NO. MODEL NO. MAX MAX MAXGPM PSI RPM DESCRIPTION

70230 9262C-C 88 124 5000 Pedestal mount, cast iron pump with12 volt heavy duty clutch with 5" diameterA-section pulley, 1¼" NPT inlet, 1" NPToutlet, counterclockwise rotation*.

70229 9263C-C 140 124 5000 Pedestal mount, cast iron pump with 12voltheavy duty clutch with 5" diameterA-section pulley,1½" NPT inlet,1¼" NPT outlet, counterclockwiserotation*.

70340 9263C-CR 140 127 5000 Same as above but clockwise rotation


H y p r o Po l y p r o p y l e n e C e n t r i f u g a l Pe d e s t a l Pu m p s

REF. PART NO. QTY. REPLACES DESCRIPTION

1 71471 1 0702-9200C Flange

2 71472 1 2120-0011 Mechanical seal Buna

2 70656 1 2120-0010 Mechanical seal viton

3 71446 1 1721-0083 O-ring

4 71447 4 2406-0020 Plug

5 71466 1 2270-0057 Washer

6 71448 1 2250-0051 Jam nut

7 71449 1 2250-0052 Impeller nut

8 71450 1 0700-9000P Pump casing9203P-S, 992538-C

8 71473 1 0701-9500P Pump casing 9500P-S92538-C

9 71198 1 1610-0012 Woodruff key

10 71474 1 0403-9000P Impeller (9203P-S)92538-C

10 71475 1 0402-9000P Impeller 9500P-S, 9553P-C

11 71452 6 2210-0087 Screw

REF. PART NO. QTY. REPLACES DESCRIPTION

12 71458 6 2270-0041 Washer

13 71476 1 0750-9000P Back cover 9203P-S,9253P-C

13 71481 1 0700-9500P Back cover 9500P-S9553P-C

14 71477 1 0506-9200 Shaft

14 71478 1 0507-9200 Optional stainless steel shaft

15 71032 2 2008-0001 Bearing

16 71134 1 1820-0025 Retaining ring

17 71451 1 2210-0088 Screw

18 71467 1 1700-0097 Gasket

19 71479 1 1410-0083 Slinger ring

20 71242 1 1610-0004 Key

21 71480 1 1700-0101 Gasket

MAX MAX MAXPART NO. MODEL NO. GPM PSI RPM DESCRIPTION

70084 9203P-S 92 75 4200 Pedestal mounted pump designed for direct drive with an electric motor or belt and pulleydrive with an electric motor or gas engine, 7/8" solid keyed 316 stainless steel shaft.

70085 9500P-S 83 75 4200 Clockwise rotation pedestal mounted pump designed for direct drive with a gas engine orelectric motor, 7/8" solid keyed 316 stainless steel shaft.

PUMP REPAIR KITSPART NO. DESCRIPTION

70665 Seal, O-Ring repair kit No. 3430-0333 consists of(1) ref. 2 mechanical seal, (1) ref. 3 O-Ring and(1)ref. 18 gasket

70666 Seal, O-Ring repair kit No. 3430-0335 consists of(1) ref. 2 mechanical seal, (1) ref. 3 O-Ring and(1)ref. 5 washer

Max. Flow Rate: 92 gpmMax. Pressure: 80 psiMax. Speed: 4200 rpmPorts: 1 1/2" npt inlet

1 1/4" npt outlet

SERIES 9200 PEDESTAL MODELS WITH 12-VOLT CLUTCHESMAX MAX MAX

PART NO. MODEL NO. GPM PSI RPM DESCRIPTION

70335 9253P-C 92 80 4200 Pedestal mount, polypropylene pump with 12 volt heavy duty clutch with 5" diameterA-section pulley, 1½" NPT inlet, 1¼" NPT outlet, counterclockwise rotation*.

70336 9553P-C 92 80 4200 Pedestal mount, polypropylene pump with 12 volt heavy duty clutch with 5" diameterA-section pulley, 1½" NPT inlet, 1¼" NPT outlet, clockwise rotation*.


Hypro Series 9400 Cast Iron and Poly Belt-Driven Models with 12-Groove Belt and Idler

P u l l y

SERIES 9402C & 9403CMAX MAX MAX PUMP

PART NO. MODEL NO. GPM PSI RPM SHAFT HOUSING NPT PORTS

70273 9402C-540 76 95 600 13/8" hollow, cast iron 1¼" inlet, 1" outlet6-spline

70274 9402C-540Q 76 95 600 13/8", 6-spline cast iron 1¼" inlet, 1" outletquick coupler

70277 9402C-540S 76 95 600 1" solid cast iron 1¼" inlet, 1" outlet

70278 9402C-1000 76 95 1000 13/8" hollow, 21 spline cast iron 1¼" inlet, 1" outlet

70279 9402C-1000L 76 95 1000 1¾" hollow, 20-spline cast iron 1¼" inlet, 1" outlet

70318 9402C-1000S 76 95 1000 1" solid cast iron 1¼" inlet, 1" outlet

70319 9403C-540 140 104 600 13/8" hollow, 6-spline cast iron 1½" inlet, 1¼" outlet

70320 9403C-540Q 140 104 600 13/8", 6-spline cast iron 1½" inlet, 1¼" outletquick coupler

70321 9403C-540S 140 104 600 1" solid cast iron 1½" inlet, 1¼" outlet70322 9403C-1000 140 104 1000 13/8" hollow, 21 spline cast iron 1½" inlet, 1¼" outlet

Hypro Series 9400 Cast Iron Self-Priming, Belt-Driven Models with 12-Groove Belt and Idler Pulley

SERIES 9403C-SPMAX MAX MAX PUMP

PART NO. MODEL NO. GPM PSI RPM SHAFT HOUSING NPT PORTS

70323 9403C-540-SP 120 99 600 13/8" hollow, cast iron 1½" inlet, 1¼" outlet6-spline

70324 9403C-540Q-SP 120 99 600 13/8", 6 spline quick cast iron 1½" inlet, 1¼" outletcoupler

70325 9403C-540S-SP 120 99 600 1" solid cast iron 1½" inlet, 1¼" outlet

70326 9403C-1000-SP 120 99 1000 13/8" hollow, 21- spline cast iron 1½" inlet, 1¼" outlet

70327 9403C-1000L-SP 120 99 1000 1¾" hollow, 20-spline cast iron 1½" inlet, 1¼" outlet

70328 9403C-1000S-SP 120 99 1000 1" solid cast iron 1½" inlet, 1¼" outlet

70333 9403C-1000L 140 104 1000 1¾" hollow 20-spline cast iron 1½" inlet, 1¼" outlet

70334 9403C-1000S 140 104 1000 1" solid cast iron 1½" inlet, 1¼" outlet

REPAIR PARTS LISTED ON NEXT PAGE


S e r i e s 9 4 0 2 C , 9 4 0 3 C a n d 9 4 0 3 C - S P

PART NO. REF. REPLACES DESCRIPTION

71176 1 2406-0007 Drain Plug

71178 2 0150-9000C Pump Casing (Models 9403C)

71234 2 0150-9200C Pump Casing (Models 9402C)

77718 2A 0150-9070C Pump Casing (Model 9403C-SP)

71179 3 2253-0002 Impeller Nut

71380 4 0401-9100P Impeller (Nylon) (Standard)

71181 4 0402-9100P Impeller (Nylon)

71236 5 1720-0083 O-Ring

71182 6 2120-0009 Mechanical Seal (Standard Viton)

71235 6 2120-0008 Mechanical Seal (optional Buna-N)

71482 6 2120-0032 Mechanical Seal (opt. Silicon Carbide)

71237 7 1830-0040 Seal Retainer

71186 8 1410-0056 Slinger Ring

PART NO. REF. REPLACES DESCRIPTION

71023 12 2000-0010 Ball Bearing 71023

71240 13 1610-0015 Key

71242 15 1610-0004 Key

71187 16 1820-0013 Bearing Retainer

71468 17 1700-0100 Gasket

77719 19 2001-0006 Driver Shaft Bearings

77720 20 1810-0012 Driver Shaft Bearing Retainer Ring

77721 21 1410-0094 Bearing Spacer

77722 22 2840-0053 End Cap

77723 23 1820-0032 Bearing Bore Retaining Ring

77724 46 3100-0006 Poly V-Belt (540 rpm)

77725 46 3100-0005 Poly V-Belt (1000 rpm)

Part No. 77715No. 3430-0475consists of (1)Silicon Sealand (1) O-Ring

Part No. 77724Repair Kit No. 3430-0477(for 1000 rpm drives)consists of (1) Ref. 46 Poly V-Belt,(1) Ref. 5 O-Ring, (1) Ref. 6Mechanical Seal (Viton), and (1)Ref. 17 Gasket.

Part No. 77725Repair Kit No. 3430-0476(for 540 rpm drives)consists of (1) Ref. 46 Poly V-Belt,(1) Ref. 5 O-Ring,(1) Ref. 6Mechanical Seal (Viton), and (1)Ref. 17 Gasket.

Part No. 70641Seal, O-ring Repair KitNo. 3430-0332 consistsof (1) Ref. 6 MechanicalSeal (Viton), (1) Ref. 5O-Ring and (1) Ref. 17Gasket.


D e l a v a n T u r b i n e P u m p


70018 26556-4 Cast iron pumpwith lip seals andnylon impeller

70019 26556-11 Cast iron pumpwith face seals andnylon impeller

TURBO-90 The Turbo-90 is designed to operate from a 1000 rpm PTO shaftwithout attachments. Peak performance at slower rotation meanslonger life of the seals.The Turbo-90 can pump suspended materials without accumula-tion unlike a conventional turbine pump. This is possible becauseof pressure relief passages from the seal cavities to the inlet port.The suspension circulates and, therefore, is cleared from the in-ner cavities. It can be used for large quantity liquid transfer – fromtrucks to tanks for instance. It is also perfect for high volumesprayer pumping applications.Features: A nylon impeller made of DuPont Super Tough NylonResin reinforced with 14% glass filler has been designed to re-duce corrosion, increase pump life and smooth operation becauseof less rotation weight. Seals available are either face seals or lipseals. Specify face seals for severe service. Face seals featurehard, wear-resistant phenolic rings pressing against ceramic seals.Bearings are isolated by drain cavities. Large 1 1/2” inlet andoutlet ports permit unrestricted high volume flow. Because of thehigh capacity of the Turbo-90, sufficient by-pass flow is availableto maintain maximum agitation. Shaft is made of stainless steeland has a 24 mm (15/16”) dia. with 6.4 mm (1/4”) keyway.

PUMP SHAFT 15/16”

PUMP CAPACITIES AND INPUT POWER (BASEDON WATER)

SPEED 0 PSI 10 PSI 20 PSI 30 PSI 40 PSI 50 PSI 60 PSIMODEL (RPM) GPM GPM GPM GPM GPM GPM GPM

26556 600 45 25 8 - - - -

26556 800 60 47 34 20 5 - -

26556 1000 75 65 55 45 33 20 10

26556 1200 90 80 73 65 55 45 35

Note: All flows based on 38.1 mm (1 1/2”) I.D. inlet and outlet hose.

SPEED 0 KPA 100 KPA 200 KPA 300 KPA 400 KPAMODEL (RPM) L/MIN L/MIN L/MIN L/MIN L/MIN

26556 600 170 72 - - -

26556 800 227 159 81 - -

26556 1000 284 231 174 112 38

26556 1200 340 297 252 202 148

Note: All flows based on 38.1 mm (1 1/2”) I.D. inlet and outlethose.REPLACEMENT PARTS FOR TURBINE PUMPREF PART NO. REPLACES DESCRIPTION REQ.

1 70839 17902 Hex nut (3/8” - 16 UNC) 6

4 70841 39923 End plate, cast iron 1

5 70842 39924 Body, cast iron 1

6 70843 26545 Gasket 1

7 26542 Seal ring (use seal kit) -

8 70845 31352-022 O-ring (viton) 1

11 70848 39925 Seal support -

13 70850 28709 Impeller, nylon 1

13a 70852 30512 Hub 1

14 70853 26544 Woodruff key 1

15 70854 26548 Snap ring, internal 2

16 70855 26665 Dust shield 1

17 71032 16228 Bearing, shielded 2

18 70856 39934 Cap screw, hex head 3(3/8” -16 UNC x 1 1/2”)

19 70857 26547 Snap ring, external 2

20 70858 39935 Name plate 1

21 70859 34793 Shaft 1

22 70860 25785 Pipe plug, square head 1

23 70861 47927 Lip seal 2

70619 50914 Face seal assembly

70888 45005 Lip seal assembly

NOTE: a high capacity Y line strainer with a 20 meshscreen must be used on the inlet side. Failure to usea suction strainer, as specified, may void the productwarranty.NOTE: If 540 rpm PTO coupler is used, capacity ofthe Turbo-90 pump will be reduced.

Max. RecommendedTemperature: 50°C (120°F)

Max. RecommendedPTO speed: 1251 rpm

REPAIR KITS FOR TURBINE PUMPPART NO. REPLACES DESCRIPTION

70606 28455-2* Pump repair kit with lip seals

70607 28455-1 Pump repair kit with face seals

PART NO. REPLACES DESCRIPTION QTY/.KIT

70843 26545* Gasket 1

70861 47927* Lip seal 2

70845 31352-022 O-Ring (viton) 2

70848 39925 Seal support 2

COUPLERS SEE PAGE 96-99


Hypro Low Pressure Diaphragm Pumps

MODEL MAX. MAX. MAX ESTIMATEDPART NO. NUMBER GPM PSI RPM DESCRIPTION WEIGHT EA.

70069 9910-D70 19 290 550 2 - diaphragm pump - 1 1/4" HB inlet, 3/4" HB outlet. Select shaft kif for 22 lbs.(replaces D60) desired drive.

70091 9910-D70GR 19 290 3600 9910-D70GR - with gear reduction for 5 hp gasoline engine 31 lbs.

70070 9910-D115 30.1 290 550 3 - diaphragm pump - 1 1/2" HB inlet, 1" HB outlet. Select shaft kit 35 lbs.(replaces D100) for desired drive.

70086 9910-D135 34.8 290 550 3 - diaphragm pump - 1 1/2" HB inlet, 1" HB outlet. 1 3/8" - 6 splined 38 lbs.(replaces D120) male shaft.

70092 9910-D160 42.5 290 550 4 - diaphragm pump - 2" HB inlet, 1 1/2" HB outlet. 1 3/8" - 6 splined 66 lbs.(replaces D150) male shaft.

70093 9910-D250 66 290 550 6 - diaphragm pump - 2" HB inlet, 1 1/2" HB outlet. 1 3/8" - 6 splined 92 lbs.(replaces D230) male shaft

Hypro low pressure diaphragm pumps are recommended forground and low-level spraying of herbicides, pesticides, liquid fer-tilizers and many other hard-to-handle fluids. Low cost maintenanceand almost wear-free operation make these pumps ideal for a widevariety of spraying jobs. Pressure and output are designed for

optimum performance of medium to large sized sprayers. Hyprolow pressure diaphragm pumps can be adapted for splined shaft,female coupler shaft, and solid shaft drive options. Pumps includea pulsation dampener.

Model 9910-D70Part No.: 70069Max Flow: 19 gpmMax Pressure: 290 psi2 Diaphragms

Model 9910-D115Part No.: 70070Max Flow: 30.1 gpmMax Pressure: 290 psi3 Diaphragms



Model 9910-D250Part No.: 70093Max Flow: 66 gpmMax Pressure: 290 psi6 Diaphragms


H y p r o L o w P r e s s u r e D i a p h r a g m P u m p P e r f o r m a n c e

ENGLISH STANDARD350 RPM 400 RPM 450 RPM 500 RPM 550 RPM

PSI GPM HP GPM HP GPM HP GPM HP GPM HP

0 12.7 0.3 13.7 0.3 15.7 0.4 17.2 0.6 19.0 0.6

145 10.7 1.2 11.0 1.4 13.5 1.6 14.9 1.8 16.0 1.9

217 10.3 1.7 10.5 2.0 13.4 2.3 14.4 2.5 15.9 2.7

290 10.0 2.2 10.0 2.5 13.0 2.8 14.1 3.1 15.8 3.4

METRIC350 RPM 400 RPM 450 RPM 500 RPM 550 RPM

BAR L/M HP L/M HP L/M HP L/M HP L/M HP

0 47.9 0.3 51.9 0.3 59.6 0.4 65.0 0.6 71.8 0.6

10 40.4 1.2 41.6 1.4 51.2 1.6 56.4 1.8 60.4 1.9

15 39.0 1.7 39.7 2.0 50.6 2.3 54.4 2.5 60.1 2.7

20 37.8 2.2 37.9 2.5 49.2 2.8 53.2 3.1 59.7 3.4



0 19.3 0.3 22.1 0.3 24.8 0.4 27.1 0.7 30.1 0.8

145 18.7 1.8 21.4 2.1 24.0 2.4 26.4 2.7 29.0 3.0

217 18.6 2.7 21.2 3.1 23.9 3.5 26.2 3.9 28.8 4.3

290 18.5 3.6 21.1 4.1 23.8 4.5 26.1 5.0 28.7 5.5



0 73.1 0.3 83.6 0.3 94.0 0.4 102.7 0.7 113.8 0.8

10 70.8 1.8 80.9 2.1 91.0 2.4 99.8 2.7 109.8 3.0

15 70.3 2.7 80.4 3.1 90.5 3.5 99.1 3.9 109.0 4.3

20 70.0 3.6 80.0 4.1 90.0 4.5 98.6 5.0 108.8 5.5



0 22.8 0.4 26.1 0.5 29.3 0.6 31.5 1.1 34.8 1.2

145 22.1 2.3 25.3 2.6 28.4 2.9 30.5 3.4 33.6 3.8

217 22.0 3.2 25.1 3.7 28.3 4.2 30.4 4.8 33.4 5.3

290 21.7 4.3 24.8 4.9 27.9 5.5 30.3 6.1 33.3 6.7



0 86.4 0.4 98.7 0.5 111.0 0.6 119.4 1.1 131.7 1.2

10 83.6 2.3 95.6 2.6 107.5 2.9 115.4 3.4 127.0 3.8

15 83.2 3.2 95.1 3.7 107.0 4.2 115.0 4.8 126.5 5.3

20 82.1 4.3 93.8 4.9 105.5 5.5 114.5 6.1 126.0 6.7

NOTE: “HP” is electrical horsepower. Consult your gas engine supplier for engine horsepower required.

SE

RIE

SD

70S

ER

IES

D70

SE

RIE

SD

135

SE

RIE

SD

115

SE

RIE

SD

115

SE

RIE

SD

135


Hypro Low Pressure Diaphragm Pump Performance



0 27.7 0.7 31.7 0.8 35.7 0.9 38.4 1.3 42.5 1.4

145 25.2 2.5 28.8 2.9 32.4 3.3 35.8 3.9 39.4 4.3

217 24.7 3.7 28.2 4.2 31.7 4.7 35.2 5.3 38.7 5.8

290 24.2 4.5 27.7 5.2 31.2 5.9 34.6 6.7 38.2 7.4



0 105.0 0.7 120.0 0.8 135.0 0.9 145.4 1.3 160.9 1.4

10 95.4 2.5 109.0 2.9 122.6 3.3 135.5 3.9 149.0 4.3

15 93.4 3.7 106.7 4.2 120.0 4.7 133.2 5.3 146.5 5.8

20 91.7 4.5 104.8 5.2 118.0 5.9 130.9 6.7 144.6 7.4



0 41.9 1.3 47.9 1.5 53.9 1.7 59.6 2.5 65.9 2.8

145 39.7 3.8 45.3 4.4 51.0 4.9 56.7 5.6 62.4 6.2

217 38.9 5.5 44.5 6.3 50.1 7.1 55.5 8.1 61.0 8.9

290 38.4 7.2 43.9 8.3 49.4 9.3 55.0 10.4 60.7 11.5



0 158.6 1.3 181.3 1.5 204.0 1.7 225.4 2.5 249.6 2.8

10 150.1 3.8 171.5 4.4 193.0 4.9 214.5 5.6 236.0 6.2

15 147.3 5.5 168.4 6.3 189.5 7.1 210.0 8.1 231.0 8.9

20 145.2 7.2 166.0 8.3 186.8 9.3 208.2 10.4 229.7 11.5

SE

RIE

SD

160

SE

RIE

SD

250

SE

RIE

SD

250

SE

RIE

SD

160


Hypro Medium Pressure Diaphragm Pumps

MODEL MAX MAX. MAX ESTIMATEDPART NO. NUMBER GPM PSI RPM DESCRIPTION WEIGHT EA.

70094 9910-D12GRGI 3.5 290 3600 2 - diaphragm pump - 3/4" HB inlet, (2) 3/8" HB outlets. Gearbox input 9 lbs.shaft is 5/8" I.D. to fit 2.5 hp gas engine.

70095 9910-D19 6.0 290 650 2 - diaphragm pump - 3/4" HB inlet, 1/2" NPT outlet. D19 - 3/4" solid 12 lbs.keyed shaft.

70096 9910-D19GRGI3/4 - - 3600 2 - diaphragm (semi-hydraulic) pump - 3/4" inlet; 5/8" NPT outlet. D19 - 3/4" 14 lbs.hollow shaft, gear reduced for 2.5 hp gas engine.

70097 9910-D19GRGI5/8 6.0 290 3600 2 - diaphragm (semi-hydraulic) pump - 3/4" inlet: 5/8" NPT outlet. D19 - 5/8" 14 lbs.hollow shaft, gear reduced for 2.5 hp gas engine.

70068 9910-D30 9.5 580 550 2 - diaphragm pump - 1" HB inlet, 1/2" HB outlet. D30AP-A-3/4" solid 23 lbs.70098 9910-D30AP-A extended shaft. Select shaft kit or gear reduction. 24 lbs.

70099 9910-D30GRGI 9.5 580 3600 2 - diaphragm pump - with GS40GI control unit & gear reduction - fits 5 hp 32 lbs.70108 9910-D30-B-GRGI gas engine. -B version with Buna-N diaphragms. 32 lbs.

70109 9910-D303 7.9 580 550 3 - diaphragm pump - 1" HB inlet, 1/2" HB outlet. 23 lbs.70111 9910-D303GRGI 3600 3 - diaphragm pump - with GR40 control unit & gear reduction that fits 5-6 hp 23 lbs.

gas engines.

70112 9910-D403 10.6 580 550 3 - diaphragm pump - 1" HB inlet, 1/2" HB outlet. 23 lbs.70113 9910-D403GRGI 3600 3 - diaphragm pump - with GR40 control unit & gear reduction that fits 5-6 hp 23 lbs.

gas engines.

70114 9910-D50 14.0 580 550 2 - diaphragm pump - 1 1/4" HB inlet, 1/2" HB outlet. D50AP-A-1" solid 35 lbs.70115 9910-D50AP-A extended shaft. Select shaft kit or gear reduction. 37 lbs.

70116 9910-D503 15.0 580 550 3 - diaphragm pump - 1 1/4" HB inlet, 3/4" NPT outlet. Select shaft kit or 28 lbs.gearbox

70117 9910-D503GRGI 15.0 580 3600 3 - diaphragm pump - assembled with gearbox 9910-KIT1642 and control 41 lbs.9910-RM40 for mounting on 8 hp gas engines.

HYPRO MEDIUM PRESSURE DIAPHRAGM PUMP GAS ENGINE UNITSMODEL MAX. MAX. MAX ESTIMATED

PART NO. NUMBER GPM PSI RPM DESCRIPTION WEIGHT EA.

70124 1534 6 290 650 Model D19 diaphragm pump with 9910-KIT1990 control unit and gearbox, 50 lbs.3 hp Briggs & Stratton gas engine with base.

70125 1535 9.5 580 600 Model D30 diaphragm pump with GS40GI control unit and KIT1640 gearbox, 82 lbs.5 hp Industrial Plus Briggs & Stratton gas engine with base.


Hypro Medium Pressure Diaphragm Pump

MODEL 9910-D12GRGI• Max. flow: 3.5 gpm• Max. pressure: 290 psi• Max. rated speed: 3600 rpm• Max. fluid temperature: 140°F• Port sizes: 3/4" inlet, 3/8" outlet, hose

barb

• Shaft: 5/8" hollow, gear reduced for 3hp gas engine

• Diaphragms: 2, semi-hydraulic• Housing: anodized aluminum• Weight: 9 lbs.• Pump shaft rotation: CW and CCW

Complete with control unit.

• Max. flow: 6 gpm• Max. pressure: 290 psi• Max. rated speed: 650 rpm (D252)

3600 rpm (70096,97,129)• Max. fluid temperature: 140°F• Port sizes: 3/4" inlet, 1/2" outlet D252• Port sizes: 3/4" inlet, 5/8" outlet

70096,97,129

• Shaft: D252 is 3/4" solid; 70096,97,129is 3/4" or 5/8" hollow, gear reduced for 2- 3 1/2 hp gas engine

• Diaphragms: 2, semi-hydraulic• Housing: anodized aluminum• Mounting base: included• Weight: 14 lbs

Recommended control unit: 9910-KIT1990 (SPP 70703)

MODEL 9910-D252, D9910-D252GRGI• Max. flow: 9.5 gpm• Max. pressure: 580 psi• Max. rated speed: 550 rpm• Max. fluid temperature 140°F

• Shaft: D30 flanged for shaft kit;D30AP-A flanged w/3/4" shaft ext.

• Port sizes: 1" inlet, 1/2” outlet, hose barb• Diaphragms: 2, semi-hydraulic• Housing components for liquid

handling: epoxy-coated• Weight: 23 lbs.

• Pump shaft rotation: CW and CCW

Recommended control unit: 9910-GS40GI (SPP 70071)

MODEL 9910-D50 AND -D50AP-A• Max. flow: 14 gpm• Max. pressure: 580 psi• Max. rated speed: 550 rpm• Max. fluid temperature: 140°F• Shaft: D50 flanged for shaft kit;

D50AP-A flanged w/1" shaft ext.

• Port sizes: 1 1/4" inlet, 1/2 " outlet, hosebarb

• Diaphragms: 2, full-hydraulic• Housing components for liquid han-

dling: epoxy-coated• Weight: 35 lbs.• Pump shaft rotation: CW and CCW

MODEL 9910-D503 (MODEL -D503GRGI IS NOT SHOWN.)• Max. flow: 15 gpm• Max. pressure: 580 psi• Max. rated speed: 550 rpm• Max. fluid temperature: 140°F• Shaft: flanged adapter• Port sizes: 1 1/4" (M) hose barb inlet,

3/4" NPT outlet

• Diaphragms: 3, semi-hydraulic• Housing: anodized aluminum• Mounting base: included• Weight: 28 lbs.• Pump shaft rotation: CW and CCW

Recommended control unit: 9910-RM40 (SPP 70706)

PART NO.

70094

PART NO.

70116

70117

PART NO.

70114

70115

PART NO.

70068

70098

PART NO.

70095

70096

70097

70129

MODEL 9910-D252, D9910-D252GRGI, 9910-D252GRG158,AND 9910-D252GRGIAP

Recommended control unit: 9910-GS40GI (SPP 70071)


H y p r o M e d i u m P r e s s u r e D i a p h r a g m P u m p P e r f o r m a n c e



145 9.2 1.2 10.6 1.5 11.6 1.8 12.7 2.2 13.7 2.5285 9.0 2.0 10.3 2.3 11.4 2.8 12.4 3.1 13.5 3.5430 8.7 2.7 10.0 3.0 11.1 3.5 12.1 4.0 13.2 4.5

580 8.4 3.4 9.8 3.8 10.8 4.4 11.9 4.9 12.9 5.4

METRIC STANDARD350 RPM 400 RPM 450 RPM 500 RPM 550 RPM

BAR L/M W L/M W L/M W L/M W L/M W

10 35 895 40 1119 44 1342 48 1641 52 186519.7 34 1492 39 1715 43 2088 47 2312 51 261129.7 33 2014 38 2238 42 2611 46 2984 50 3357

40.6 32 2536 37 2834 41 3282 45 3655 49 4028

ENGLISH STANDARD450 RPM 550 RPM 650 RPM

PSI GPM HP GPM HP GPM HP

50 4.2 .33 5.1 .43 6 .53

100 4.1 .37 5 .47 5.9 .57

150 4 .4 4.9 .5 5.8 .6

200 3.8 .5 4.7 .6 5.5 .8

290 3.6 .6 4.5 .8 5.3 1

METRIC STANDARD450 RPM 550 RPM 650 RPM

BAR L/MIN W L/MIN W L/MIN W

3.5 15.8 245 19.2 320 22.7 395

7 15.4 275 18.8 350 22.3 425

10.5 15.2 300 18.6 375 22 445

14 14.5 375 17.8 445 21 595

20.3 13.8 445 17 595 20 745

350 RPM 450 RPM 550 RPMPSI GPM HP GPM HP GPM HP

50 6 .4 7.9 .8 9.5 1.6

100 5.9 .9 7.8 1.3 9.3 2

200 5.7 1.3 7.5 1.8 9.1 2.5

300 5.5 1.6 7.4 2.2 9 2.8

400 5.3 2.2 7.1 2.8 8.7 3.6

580 5 2.7 6.9 3.4 8.45 4.2

350 RPM 450 RPM 550 RPMBAR L/MIN W L/MIN W L/MIN W

3.5 23 300 30 600 36 1190

7 22.5 670 29.5 970 35.2 1490

14 21.5 970 28.5 1340 34.5 1860

21 21 1190 28 1640 34 2090

28 20 1640 27 2085 33 2680

40.6 19 2012 26 2535 32 3130

350 RPM 450 RPM 550 RPMPSI GPM HP GPM HP GPM HP

50 9.5 .6 11.9 1 14 1.5

100 9.3 1 11.7 1.6 13.8 2

200 9.1 1.6 11.5 2.3 13.6 3

300 9 2 11.4 2.8 13.5 3.5

400 8.7 2.7 11 3.5 13.2 4.5

580 8.45 3.5 10.8 4.5 12.7 6.5

350 RPM 450 RPM 550 RPMBAR L/MIN W L/MIN W L/MIN W

3.5 36 450 45 745 53 1120

7 35.2 745 44.2 1190 52.3 1490

14 34.5 1190 43.5 1715 51.5 2235

21 34 1490 43 2090 51 2610

28 33 2010 42 2610 50 3350

40.6 32 2610 41 3350 48 4840

9910

-D25

299

10-D

252G

R99

10-D

3099

10-D

30A

P-A

9910

-D25

299

10-D

252G

R

9910

-D50

9910

-D50

AP-

A

9910

-D50

9910

-D50

AP-

A99

10-D

3099

10-D

30A

P-A

MO

DE

L99

10-D

503

MO

DE

L99

10-D

503



0 2.4 .02 2.6 .02 3.0 .03 3.2 .04 3.5 .04140 2.3 .3 2.5 .3 2.9 .4 3.0 .5 3.2 .5210 2.2 .4 2.4 .4 2.8 .5 2.9 .6 3.1 .6

290 2.1 .5 2.3 .5 2.5 .6 2.8 .7 3.0 .8


BAR L/M W L/M W L/M W L/M W L/M W

0 9.4 134 10.3 156 11.3 224 12.2 291 13.2 3069.8 9.0 216 9.8 231 10.7 298 11.5 365 12.5 380

14.7 8.6 291 9.4 306 10.2 372 11.0 440 12.0 45520.3 8.2 365 9.0 380 9.8 447 10.6 522 11.8 596

MO

DE

L99

10-D

12G

RG

IM

OD

EL

9910

-D12

GR

GI


Hypro High Pressure Diaphragm Pumps

CONTROL MAX MAX PUMPPART NO. UNIT MODEL GPM PSI MODEL

70708 9910-GS50GI 48 725 All models

70710 9910-VDR50 35 725 -D813, -D1064, and -D1265

Hypro high pressure diaphragm pumps are recommended for spraying of herbicides, pesticides, liquid fertilizers and many other hardto handle fluids. Low cost maintenance and almost wear-free operation make these pumps ideal for a wide variety of spraying jobs.Pressure and output are designed for optimum performance of medium to large sized sprayers.Hypro high pressure diaphragm pumps are supplied with single or double splined thru-shafts. Pumps include pulsation dampeners.

CONTROL UNITS 9910-GS50GI & 9910-VDR50Control units are available for easy flow and pressure control ofyour sprayer system. These units include a pressure relief valve tocontrol pressure, an oil-filled pressure gauge to monitor pressure,and outlet ball valves to control flow. Control Unit 9910-GS50GIcan be remote mounted with Kit No. 9910-KIT1742 (70709).No additional kit is required for remote mounting Control Unit9910-VDR50.

MODEL MAX. MAX. MAX ESTIMATEDPART NO. NUMBER GPM PSI RPM DESCRIPTION WEIGHT EA.

70118 9910-D813 21.4 725 550 3 - diaphragm pump - 1 1/4" HB inlet, 3/4" NPT outlet. Select shaft kit or 48 lbs.gearbox. 1 3/8” -6 splined male shaft extension.

70119 9910-D813GRGI 21.4 725 3600 3 - diaphragm pump assembled with gearbox 9910-KIT 1642 and control 60 lbs.9910-VDR50 for mounting on 11 hp gas engines.

70090 9910-D1064 28 725 550 4 - diaphragm pump - 1 1/2" HB inlet, 3/4" NPT outlet. Select shaft kit or 54 lbs.gearbox. 1 3/8" -6 splined male shaft extension.

70120 9910-D1064GRGI 28 725 3600 4 - diaphragm pump assembled with gearbox 9910-KIT 1642 and control 65 lbs.9910-VDR50 for mounting on 18 HP gas engines.

70121 9910-D1265 33.2 725 550 5 - diaphragm pump - 1 1/2" HB inlet, 3/4" NPT outlet. 1 3/8" -6 splined male 66 lbs.shaft extension

70122 9910-D1516 40 725 550 6 - diaphragm pump - 1 1/2" HB inlet, 3/4" NPT outlet. 1 3/8" -6 splined male 78 lbs.shaft extension.

70123 9910-D1554 41 725 550 4 - diaphragm pump - 1 1/2" HB inlet, 3/4" HB outlet, 1 3/8" - 6 splined male 120 lbs.shaft extension. Complete with pulsation dampener.

MODEL 9910-D813Part No.: SPP 70118Max. flow: 21.4 gpmMax. pressure: 725 psiMax. speed: 550 rpm3 Diaphragms

MODEL 9910-D1516Part No.: SPP 70122Max. flow: 40 gpmMax pressure: 725 psiMax speed: 550 rpm6 Diaphragms

MODEL 9910-D1064Part No.: SPP 70090Max. flow: 28 gpmMax. pressure: 725 psiMax. speed: 550 rpm4 Diaphragms

MODEL 9910-D1554Part No.: SPP 70123Max. flow: 41 gpmMax. pressure: 725 psiMax. speed: 550 rpm4 Diaphragms

MODEL 9910-D1265Part No.: SPP 70121Max. flow: 33.2 gpmMax. pressure: 725 psiMax. speed: 550 rpm5 Diaphragms


Hyp ro H igh Pre s su re D iaph ragm Pump Per fo rmance



0 14.7 2.2 17.0 2.5 18.2 2.9 19.7 3.5 20.8 3.6435 13.5 4.1 15.5 4.6 17.3 5.3 19.0 5.9 19.6 6.3580 13.4 5.3 15.2 6.0 17.1 6.8 18.3 7.6 19.2 8.1

725 13.3 6.4 14.9 7.4 16.9 8.4 17.8 9.3 18.7 9.9


BAR L/MIN HP L/MIN HP L/MIN HP L/MIN HP L/MIN HP

0 55.6 2.2 64.3 2.5 68.7 2.9 74.6 3.5 78.6 3.530 51.1 4.1 58.7 4.6 65.5 5.3 71.9 5.9 74.2 6.340 50.8 5.3 57.7 6.0 64.8 6.8 69.3 7.6 72.6 8.150 50.4 6.4 56.5 7.4 63.9 8.4 67.5 9.3 70.8 9.9



0 18.9 2.8 21.5 3.1 24.2 3.9 25.4 4.4 27.9 5.0435 18.6 4.4 20.7 5.4 23.5 6.7 25.2 7.1 27.6 7.5580 18.1 5.5 18.7 6.2 21.0 7.8 24.8 8.3 27.2 9.1

725 17.5 8.5 16.3 9.9 18.3 11.1 24.3 12.2 26.7 13.1



0 71.6 2.8 81.5 3.1 91.6 3.9 96.1 4.4 105.6 5.030 70.3 4.4 78.4 5.4 89.0 6.7 95.2 7.1 104.3 7.540 68.4 5.5 70.9 6.2 79.6 7.8 93.7 8.3 103.0 9.150 66.2 8.5 61.6 9.9 69.2 11.1 91.9 12.2 101.0 13.1



0 23.8 3.8 26.8 4.5 29.7 5.1 31.9 5.5 33.3 5.8435 22.4 7.0 25.5 8.0 28.7 9.1 31.4 9.7 32.7 10.2580 22.2 9.1 25.3 10.4 28.4 11.8 31.1 12.5 32.6 12.8

725 22.1 11.2 25.0 12.3 28.2 14.6 30.8 15.5 31.4 15.6



0 90.0 3.8 101.5 4.5 112.6 5.1 120.7 5.5 126.1 5.830 84.8 7.0 96.7 8.0 108.5 9.1 118.9 9.7 123.9 10.240 84.2 9.1 95.7 10.4 107.5 11.8 117.7 12.5 123.4 12.850 83.7 11.2 94.8 12.3 106.8 14.6 116.4 15.5 118.7 15.6

MO

DE

L99

10-D

813

MO

DE

L99

10-D

813

MO

DE

L99

10-D

1265

MO

DE

L99

10-D

1265

MO

DE

L99

10-D

1064

MO

DE

L99

10-D

1064


Hypro High Pressure Diaphragm Pump Performance



0 27.7 4.5 31.6 5.4 34.9 6.1 36.3 6.7 39.8 7.1435 26.4 8.2 30.4 9.6 33.9 10.8 35.9 11.5 39.5 12.0580 26.2 10.5 30.2 12.3 33.7 13.9 35.8 14.7 39.3 15.3725 26.0 12.9 29.9 15.1 33.5 16.9 35.7 17.9 38.4 18.6



0 104.7 4.5 119.7 5.4 132.0 6.1 137.5 6.7 150.6 7.130 100.0 8.2 115.2 9.6 128.3 10.8 135.8 11.5 149.4 12.040 99.1 10.5 114.2 12.3 127.7 13.9 135.6 14.7 148.6 15.350 98.3 12.9 113.2 15.1 126.7 16.9 135.3 17.9 145.3 18.6

MO

DE

L99

10-D

1516

ENGLISH STANDARD450 RPM 550 RPM

PSI GPM HP GPM HP

100 40.7 4.5 42.3 5.2300 40 8.1 41.7 8.5500 39 15.7 40.6 16.1725 38.5 19.4 40.1 20.2

METRIC STANDARD450 RPM 550 RPM

BAR L/MIN HP L/MIN HP

7 154 4.5 160 5.2

21 151.4 8.1 157.8 8.5

35 147.6 15.7 153.7 16.1

50 145.7 19.4 151.8 20.2

Note: The “HP” shown is electrical horsepower. Consult yourgas engine supplier for the engine horsepower required.

MO

DE

L99

10-D

1554

MO

DE

L99

10-D

1554

MO

DE

L99

10-D

1516


H y p r o D i a p h r a g m P u m p s

CONTROL UNITS FOR PRESSURE AND OUTPUT CONTROL OF SPRAYERS

MODEL MAX. MAX. ESTIMATEDPART NO. NUMBER GPM PSI DESCRIPTION WEIGHT EA.

70702 9910-KIT1994 3.5 290 Control unit for Model 9910-D12GRGI. Includes relief valve and two 3/8" hose 1 lbs.barb outlets.

70703 9910-KIT1990 6.0 290 Control unit for mounting on 9910-D19 model pump. Includes relief valve and 1 lbs.pressure/bypass selector. 5/8" HB bypass port and 3/8” HB outlet.

70071 9910-GS40GI 21 580 Control unit for mounting on 9910-D30 and D50 model pumps. Includes high 3.5 lbs.Repair Kit 70668 pressure relief valve and 3 1/2" HB outlets with individual shut-offs.

70704 9910-KIT1741 - - Remote mounting kit for 9910-GS40GI control unit. Includes mounting bracket, bolts, 1 lbs.and hose barb.

70705 9910-GR40 11 580 Control unit for 9910-D303 and D403 model pumps include adjustable high pressure 2 lbs.relief valves, complete bypass lever, 2 1/2" guage, outlet barbs and 5/8” bypass barb.

70706 9910-RM40 24 580 Control unit for 9910-D503 model pump. Includes high pressure relief valve and two 3.5 lbs.1/2” HB outlet with individual shut-offs. Unit can be either direct or remote mounted.

70707 9910-KIT1897 - - Remote mounting kit for 9910-RM40. 2 lbs.

70708 9910-GS50GI 48 725 Remote control unit for Models 9910-D813, -D1064, -D1265, -D1516, and D1554 8.5 lbspumps, Includes relief valve and three 1/2” HB outlets with individual shut-offs.

70709 9910-KIT1742 - - Remote mounting kit for 9910-GS50GI control unit. Includes mounting bracket, 1.25 lbsbolts and hose barb.

70710 9910-VDR50 35 725 Control unit for mounting on Models 9910-D503, -D813, - D1064, and -D1265 pumps. 3.5 lbs.Includes high pressure relief valve and two 1/2" HB outlets with individual shut-offs.For additional hose barbs, order 9910-130491 (71754).

70087 3300-0087 42.5 290 Remote control units for 9910-D70, -D115, -D135, and -D160 pumps. Includes 7.75 lbs70712 3300-0088 built-in relief valve, 1" HB inlet, and each unit is supplied with the following hose barb

outlets that can be interchanged onto the individual shut-off valves:(3) 3/8" HB outlets(3) 1/2" HB outlets(3) 3/4" HB outletsmodel 3300-0088 includes a manual by-pass lever.

70713 3300-0082 66 290 Remote control unit for models 9910-D250 pumps. Unit maintains constant pressure 18 lbs.of the system when a boom section is shut off. Includes main shut-off valve, single1 1/2"HB return for all four 3/4" HB outlets, and 1 1/2" HB inlet.

70702 70703 70071 70710 70706

70708 70087 70713



GEAR REDUCTION KITSMODEL ESTIMATED

PART NO. NUMBER DESCRIPTION WEIGHT EA.

70698 9910-KIT1640 For Model 9910-D30, D303 and D403 pumps 6:1 gear box for standard 5 hp gas engines with 6.5 lbs.3/4” shaft.

70714 9910-KIT1642 For Model 9910-D50, D503, D813, D1064 and D1265 pumps 6:1 gear box for standard 8-18 hp 8.5 lbs.gas engine with 1” shaft.

1-3/8-6B FEMALE PTO SHAFT KITSMODEL ESTIMATED


70697 9910-KIT1704 For Model 9910-D50, D30 7 lbs.

70667 9910-KIT1708 For Model 9910-D70 and Model 9910-D115 pumps 5.25 lbs.

70715 9910-KIT2204 For Model 9910-D503 7 lbs.

Kits include female PTO coupler and retaining clamp, torque arm and mounting bracket, chains, and necessaryhardware.

1-3/8-6B MALE PTO SHAFT KITSMODEL ESTIMATED


70699 9910-KIT1702 For Model 9910-D30 pumps 3 lbs.

70716 9910-KIT1706 For Model 9910-D50 4.25 lbs.

70717 9910-KIT1710 For Model 9910-D70 and Model 9910-D115 pumps 5.5 lbs.


70719 9910-KIT2201 For Models 9910-D813, D1064, D1265 pumps 4.25 lbs.

Kits include male PTO shaft adapter, mounting bracket and necessary hardware.

1” SOLID SHAFT KITSMODEL ESTIMATED


70701 9910-KIT1703 For Model 9910-D30 pumps 2.5 lbs.


70669 9910-KIT1711 For Model 9910-D70 and Model 9910-D115 pumps 5 lbs.


70723 9910-KIT2203 For Model 9910-D813, D1064, D1265 pumps 3.75 lbs.

Kits include solid shaft adapter, mounting bracket and necessary hardware.

HYDRAULIC MOTOR MOUNTING FLANGE KITMODEL FITS DIAPHRAGM ESTIMATED

PART NO. NUMBER DESCRIPTION PUMP MODELS WEIGHT EA.

70724 9910-HYD5312 Hydraulic motor mounting flange kit that includes one 9910-D30, D303, D403, D50, D503, 5.5 lbs.flange, one 1" hollow shaft and two bolts. D813, D1064 and D1265

70725 9910-HYD1570 Hydraulic motor mounting flange kit that includes one 9910-D160 and D250 2.5 lbs.flange, one coupling and six bolts.

70726 9910-HYD5341 Hydraulic motor mounting flange kit that includes one 9910-D115 and D70 5.5 lbs.coupling and two pins.

70726 70725 70724

70698 70714


DIAPHRAGM PUMP REPAIR KITS

PART FOR PUMP KIT MODELNUMBER MODEL 9910- NUMBER DESCRIPTION

71755 D70 9910-KIT2363 Diaphragm kit71756 9910-KIT2364 Valve kit71757 9910-KIT2365 O-Ring kit

71831 D115 and D135 9910-KIT2369 Diaphragm kit71832 9910-KIT2370 Valve kit71833 9910-KIT2026 O-Ring kit



71840 D12GRGI and 9910-KIT1882 Diaphragm kit71841 D12GI/12V 9910-KIT1992 Valve kit

71842 D503 9910-KIT1881 Diaphragm kit71843 9910-KIT1987 Valve kit

71844 D19 9910-KIT1723 Diaphragm kit71845 (all versions) 9910-KIT1914 Valve kit71846 9910-KIT1913 O-Ring kit

71847 D30 9910-KIT2110 Diaphragm kit (Buna-N diaphragm)70644 (all versions) 9910-KIT1724 Diaphragm kit (Desmopan diaphragm)71848 9910-KIT1917 Valve kit70643 9910-KIT1916 O-Ring kit

71849 D50 9910-KIT2111 Diaphragm kit (Buna-N diaphragm)70652 9910-KIT1725 Diaphragm kit (Desmopan diaphragm)71850 9910-KIT1920 Valve kit70653 9910-KIT1919 O-Ring



71856 D1265 9910-KIT2100 Diaphragm kit71854 9910-KIT1964 Valve kit71855 9910-KIT2378 O-Ring kit71857 D1554 9910-KIT1734 Diaphragm Kit71858 9910-KIT1965 Valve kit71859 9910-KIT1744 O-Ring kit




Hypro Diaphragm Pump- Replacement parts for pump 9910-D30


2 71254 9910-620101 Head assembly (right hand) 13 71255 9910-620102 Head assembly (left hand) 14 71256 9910-320130 Nut (12MA) 85 71406 9910-620085 Diaphragm (Desmopan) 26 71257 9910-620120 Piston 27 71258 9910-620140 Connecting rod 18 71259 9910-620110 Piston sleeve 29 71260 9910-580130 Retainer ring 2

10 71261 9910-380300 Connecting rod pin 211 71262 9910-380080 Retainer ring 412 71263 9910-160230 Piston ring 213 71264 9910-580360 Retaining bolt 2* 71266 9910-550131 Lock nut 2

16 71267 9910-180150 Nut (10MA) 2* 71268 9910-550200 Stud 2

18 71245 9910-620030 O-Ring 421 71271 9910-620025 Oil sealing cap 122 71246 9910-620210 O-Ring 123 71272 9910-620291 Retaining ring 124 71273 9910-620190 Ball bearing 225 71274 9910-390440 Nut 226 71275 9910-550331 Washer 227 71276 9910-550330 Stud 128 71247 9910-180101 O-Ring 129 71277 9910-550030 Oil sight glass 130 71248 9910-550040 O-Ring 131 71278 9910-550056 Cap for oil sight glass 132 71279 9910-620160 Spacer washer 133 71280 9910-550060 Roller bearings 134 71281 9910-620130 Seal 135 71282 9910-620330 Retainer ring 136 71283 9910-620170 Crankshaft 137 71284 9910-620150 Manifold 138 71285 9910-550340 Threaded adapter 139 71249 9910-550350 O-Ring 140 71286 9910-550242 Barb nut 141 71287 9910-550370 Hose barb 142 71250 9910-390060 O-Ring 4

71289 9910-390270 Nut 844 71407 9910-621780 Bolt (8MAx40) 8

*Not shown


45 71291 9910-620230 Accumulator head 145B 71316 2270-0004 Washer 246 71244 9910-550190 Accumulator diaphragm 147 71292 9910-622070 Accumulator pressure assy. 148 71293 9910-30211 Studs 249 71408 9910-650542 O-Ring 150 71294 9910-180020 Air valve 151 71252 9910-390290 O-Ring 152 71295 9910-620680 Key 153 71296 9910-620172 Crankshaft (AP model) 155 71297 9910-620661 Retainer 156 71409 9910-620670 Washer 157 71299 9910-180370 Bolt 158 71436 9910-620630 Seal 159 71300 9910-620021 Spacer 160 71324 9910-650660 Damper body 161 71325 9910-650670 Damper diaphragm 162 71326 9910-650690 Clamp 1

63A 71317 2840-0028 Shield 165 71273 9910-620190 Ball Bearing 166 71301 9910-620240 Male 6 spline 1 3/8" PTO shaft 167 71302 9910-620470 Bolt (10 MAx20) 368 71303 9910-200231 Lock washer 469 71304 9910-621600 1" solid shaft 170 71305 9910-500160 Collar 171 71306 9910-620270 Female 6 spline 1 3/8" PTO adapter 172 71256 9910-320130 Nut 173 71307 9910-320131 Washer 174 71308 9910-500171 Lock retaining washer 175 71309 9910-320170 Bolt (12MAx75) 176 71310 9910-620340 Bolt (12MAx20) 178 71312 9910-620650 Torsion spring 179 71313 9910-320640 Chain (450 mm) 180 71314 9910-320641 Chain (320 mm) 181 71315 9910-320650 “S” hook 382 71318 9910-380200 Base 283 71319 9910-380210 Bolt (8MAx75) 284 71320 9910-380241 Lock washer 285 71321 9910-380240 Nut 286 71322 9910-450145 Discharge flange housing 187 71323 9910-110130 Hose barb & nut 488 71289 9910-390270 Nut 2


H y p r o D i a p h r a g m P u m p

REPLACEMENT PARTS FOR PUMP 9910-D60REF. PART NO. REPLACES DESCRIPTION QTY.

REQ.

1 71327 9910-550010 Pump body 1

2 71328 9910-550101 Head assembly (right hand) 1

3 71329 9910-550102 Head assembly (left hand) 1

4 71330 9910-550150 Manifold 1

5 71331 9910-559200 Accumulator pressure assembly 1

7 71332 9910-550080* Diaphragm 2

7 71333 9910-55008V Viton diaphragm 2

8 71334 9910-550110 D60BP piston sleeve 2

9 71335 9910-550120 Piston 2

10 71336 9910-320030*^ O-Ring 4

11 71395 9910-759050 Check valve assembly 4

12 71338 9910-550020 Stud 2

13 71267 9910-180150 Nut 8

14 71266 9910-550131 Lock nut 2

15 71286 9910-550242 Barb nut 2

16 71287 9910-550370 1” hose barb (inlet) 1

17 71339 9910-550380 3/4” hose barb (outlet) 1

18 71249 9910-550350^ O-Ring 2

19 71285 9910-550340 Threaded adapter 2

20 71267 9910-180150 Nut 2

21 71268 9910-550200 Stud 8

23 71340 9910-550310 Roller bearing 1

24 71252 9910-390290^ O-Ring 4

25 71276 9910-550330 Stud 2

26 71341 9910-550300 Air valve 1

27 71251 9910-650540^ O-Ring 1

28 71342 9910-180371 Bolt (8MAx25) 4

29 71343 9910-550230 Accumulator head 1

30 71244 9910-550190* Accumulator diaphragm 1

31 71321 9910-380240 Nut 4

32 71278 9910-550056 Cap for oil sight glass 1

33 71248 9910-550040^ O-Ring 1

34 71277 9910-550030 Oil sight glass 1

35 71274 9910-390440 Nut 2

36 71247 9910-180101^ O-Ring 1

37 71344 9910-550290 Roll pin


38 71256 9910-320130 Nut 1

39 71307 9910-320131 Washer 1

40 71305 9910-500160 Collar 1

42 71309 9910-320170 Bolt (12MAx75) 1

43 71345 9910-550250 Female splined shaft 1

44 71346 9910-200391 Retainer ring 1

45 71347 9910-550470 Seal ring 1

46 71348 9910-550070 Spacer for crankshaft 1

47 71280 9910-550060 Roller bearing 1

48 71349 9910-550170 D60BP crankshaft 1

49 71315 9910-320650 Chain, S hook 4

50 71313 9910-320640 Chain 1

51 71267 9910-180150 Nut 2

52 71303 9910-200231 Washer 2

53 71350 9910-320620 Washer 1

54 71351 9910-320630 Bolt 1

55 71352 9910-580020 Stud 2

56 71313 9910-320640 Chain 1

57 71353 9910-550280 Roller bearings 2

58 71354 9910-550140 Piston backup 1

59 71264 9910-580360 Retaining bolt 2

61 71355 9910-580080 Base 1

64 71357 9910-550160 Spacer sleeve 1

65 71358 9910-320610 Wing nut 1

66 71359 9910-550491 Oil seal cover 1

67 71360 9910-550480 Oil seal spacer ring 1

68 71361 9910-130171 Oil drain plug 1

69 71362 9910-550510 Adapter 1

70 71304 9910-621600 1" solid shaft 1

71 71301 9910-620240 1 3/8" male 6 spline PTO shaft 1

72 71303 9910-200231 Washer 3

73 71302 9910-620470 Bolt 3

74 71317 2840-0028 Safety shield 1

75 71316 2270-0004 Washer 4

REPAIR KITS FOR PUMPPART NO. REPLACES DESCRIPTION

70645 9910-KIT1720* Diaphragm repair kit

70646 9910-KIT1902^ O-Ring repair kit

9910-D60 PARTS ONLY


H y p r o D i a p h r a g m P u m p

9910-D100 PARTS ONLY

REPLACEMENT PARTS FOR PUMP 9910-D100REF. PART NO. REPLACES DESCRIPTION QTY.

REQ.

1 71363 9910-580010 Pump body 1

2 71364 9910-580150 Manifold 1

3 71328 9910-550101 Head assembly (right hand) 2

4 71329 9910-550102 Head assembly (left hand) 1

5 71267 9910-180150 Nut 12

8 71332 9910-550080* Diaphragm 3

9 71366 9910-580110 Piston sleeve 3

10 71367 9910-500260 Piston ring 3

11 71264 9910-580360 Retaining bolt 3

12 71368 9910-580120 Piston 3

13 71261 9910-380300 Connecting rod pin 3

14 71262 9910-380080 Retainer ring 6

15 71369 9910-580140 Connecting rod 3

16 71336 9910-320030*^ O-Ring 6

17 71395 9910-759050 Check valve assembly 6

18 71370 9910-580060 Hose barb nut 1

19 71252 9910-390290^ O-Ring for adapter 2

20 71371 9910-580030 Adapter 1

21 71289 9910-390270 Nut 3

22 71267 9910-180150 Nut 3

23 71372 9910-580050^ O-Ring 1

24 71373 9910-280030 Stud 3

25 71374 9910-580180 Accumulator pressure assembly 1

26 71244 9910-550190* Accumulator diaphragm 1

27 71343 9910-550230 Accumulator head 1

28 71341 9910-550300 Air valve 1

29 71251 9910-650540 O-Ring 1

30 71342 9910-180371 Bolt (8MAx25) 4

31 71346 9910-200391 Retainer ring 1

32 71347 9910-550470 Seal 1

33 71348 9910-550070 Spacer ring 2

34 71280 9910-550060 Roller bearing 1

35 71349 9910-550170 Crankshaft 1

36 71260 9910-580130 Retainer ring 2

37 71268 9910-550200 Stud 12

38 71340 9910-550310 Roller bearing 1

39 71276 9910-550330 Stud 2

40 71247 9910-180101^ O-Ring 1


41 71277 9910-550030 Oil sight glass 1

42 71274 9910-390440 Nut 2

43 71248 9910-550040^ O-Ring 1

44 71278 9910-550056 Cap for oil sight glass 1

45 71321 9910-380240 Nut 4

46 71285 9910-550340 Threaded adapter 1

47 71249 9910-550350^ O-Ring 1

48 71287 9910-550370 1" hose barb (outlet) 1

49 71286 9910-550242 Barb nut 1

50 71375 9910-580040 1 1/8" hose barb (inlet) 1

51 71338 9910-550020 Stud 3

52 71376 9910-250310^ Adapter 1

53 71359 9910-550491 Oil seal cover 1

54 71360 9910-550480 Spring for pressure ring 1

55 71361 9910-130171 Oil drain plug 1

56 71317 2840-0028 Safety shield 1

57 71316 2270-0004 Washer 4

58 71256 9910-320130 Nut 1

59 71307 9910-320131 Washer 1

60 71305 9910-500160 Collar 1

61 71308 9910-500171 Lock retaining washer 1

62 71309 9910-320170 Bolt(12MAx75) 1

63 71344 9910-550290 Roll pin 2

64 71345 9910-550250 Female splined shaft 1

65 71377 9910-380271 Torque bracket 1

66 71267 9910-180150 Nut 2

67 71303 9910-200231 Lock washer 2

68 71378 9910-650340 S hook 4

69 71313 9910-320640 Chain 2

70 71358 9910-320610 Wing nut 1

71 71350 9910-320620 Washer 1

72 71351 9910-320630 Eye bolt 1

74 71302 9910-620470 Bolts 3

75 71303 9910-200231 Washer 3

76 71301 9910-620240 1 3/8" male 6 spline PTO shaft 1

77 71362 9910-550510 Adapter 1

78 71304 9910-621600 1" solid shaft 1

80 71355 9910-580080 Base 1

82 71379 9910-540300 Bolt (10MAx30) 1

REPAIR KITS FOR PUMPPART NO. REPLACES DESCRIPTION

70647 9910-KIT1721* Diaphragm repair kit

70648 9910-KIT1905^ O-Ring repair kit


Flojet Electric Diaphragm Pumps

NEW OLD DEMAND SWITCH PRESSURE GALLONSPART NO. REPLACES REPLACES VOLTS AMPS OR RELIEF VALVE RANGE PER MIN.

70240 2100-755 12 7 Demand Switch 25 - 60 1 - 2

70241 2100-894 12 7 Relief Valve **0 - 45 1 - 2

70242 2100-734 2100-774 12 7 Relief Valve **0 - 30 1 - 2

70243 4300-142 12 9 Demand Switch 30 - 45 3.7

70244 2100-959 12 8 Relief Valve **0 - 70 1 - 2

70257 2100-615 12 8 Relief Valve **0-60 1 - 22

70262 2100-979 115 .5 Relief Valve 0 - 60 1 - 2

70245 2100-914 2100-855 115 .5 Relief Valve **0 - 50 1 - 2

70179 D3835V5011 115 .5 Demand Switch 0 - 60 1 - 2

70246 D3225H1411 2100-856 24 4.0 Relief Valve 0-70 1 - 2

70247 2100-573 12 7 Relief Valve **0 - 70 1 - 2.1

70254 D3135B1411 2100-596 12 7 Relief Valve **0 - 31 1 - 1.1

70255 2100-840 12 7 Relief Valve **0 - 50 1 - 2.1

70198 4300-504A 12 14 Demand Switch 0-40 4.570197 4100-502A 12 14 on/off 0-40 4.5

**Non Adjustable Pressure

• DEMAND SWITCH MODELS operate only when liquid flow isrequired. Pump and motor stop instantly when discharge isclosed.

• RELIEF VALVE MODELS have pressure controlled by aninternal relief valve, and run continuously unless electriccurrent is turned off

• Diaphragm design eliminates troublesome shaft seal.• Pump can be run indefinitely without damage.• No metal comes in contact with liquid being pumped.• Ball bearing drive – assures longer pump life.• Excellent self-priming capability.• Nitrile diaphragms and viton valves are standard.• Small solids, such as dirt, sand, and powders will not damage

pump.• Maximum temperature of pumped liquid 160°F (71°C).• Permanent magnet motor – long life brushes.• Not to be used for Petroleum based products

PART NO. DESCRIPTION

SPP 71727*** Viton check valve repair kit for 2000 & 2100 series relief valve pumps (includes check valve & o-Ring)

SPP 71728**** Viton check valve repair kit for 2000 & 2100 series demand pumps (includes check valve & o-Ring)

SPP 70692** Nitrile diaphragm repair kit for 2000 & 2100 series pumps (includes diaphragm & pistons)

SPP 70693* Cam bearing repair kit for 2100 series pumps (includes cam bearing set screw)

SPP 70694 Diaphragm repair kit for 4300 series pumps (includes pistons & screens)

SPP 70695 Check valve repair kit for 4300 series pumps (includes o-ring & ferrules)

SEE PARTS BREAKDOWNON NEXT PAGE AND PAGE 1-71

SPP 70240DEMAND PUMP

SPP 70242RELIEF VALVE PUMP


Floject Electric Disphragm Pump

PARTS LIST FOR 2000 SERIES FLOJET PUMPS (MANUFACTURED UNTIL SEPTEMBER 1989)

REF PART NO. REPLACES DESCRIPTION QTY.

1 71720 02009-004 Motor 12 Volt 1

1 71721 02029-000 Motor 110 Volt 1

2 71722 11028-101 Base 1

3 71723 20132-000 Grommets set of 4

7 71725 21022-012 Cam bearing Assembly 1

8 71726 20016-000 Bearing Cover 1

9 See Kit See ** Piston inner & outer 2(includes No. 11)

11 See Kit See ** Diaphragm (includes No. 9) 1

12 71727 20028-086 Check valve assembly Viton 1(relief valve pump)***

12 71743 20028-022 Check Valve assembly Buna 1(relief valve pump)

12 71728 20028-087 Check valve assembly Viton 1(demand pump)****

14 71730 91005-001 Relief valve spring 20-30 psi 2

16 71732 02095-100 Pressure switch (demand pump) 1

71733 20097-001 Brush kit (12 volt) set of 2

71747 21010-002 Diaphragm Buna

71749 21010-004 Diaphragm EPDM

REPAIR KITS FOR 2000 SERIES PUMPSPART NO. REPLACES DESCRIPTION

71747** 21010-002 Diaphragm kit Nitrile

71727*** 20028-086 Viton check valve assy.(relief valve pump)

71728**** 20028-087 Viton check valve assy.(demand pump)

REF PART NO. REPLACES DESCRIPTION QTY.

1 71720 02009-004 Motor 12 volt 1

1 71721 02029-000 Motor 110 volt 1

2 71734 20115-116 Brush end bell assy. (D.C.) 1

3 71722 11028-101 Base plate 1

4 71723 20132-000 Grommet set of 4

5 71735 20131-002 Screw (for base plate) 2

7 71737 20552-000 Set screw (for cam bearing) 1

8 See kit See * Cam/bearing 1

9 71738 20428-100 P.P. bearing cover 1

10 See kit See ** Piston (inner & outer) 2

12 See kit See ** Diaphragm 1

13 71727 20028-086 Check valve assembly Viton 1(relief valve pump)***

13 71743 20028-022 Check valve assembly Buna 1(relief valve pump)

13 71728 20028-087 Check valve assembly Viton 1(demand switch pump)****

15 71739 20378-003 Bypass spring 60 to 70 psi 2(relief valve pump)

16 71740 20500-507 P.P. pump housing 1

17 71732 02095-100 Pressure switch 60 psi 1(demand pump)

* 71748 5157096 Fuse Holder

18 71736 20131-001 Pump Screw

71747 21010-002 Diaphragm Buna

71749 21010-004 Diaphragm EPDM

71750 20028-008 Santoprene check valve assembly(demand pump)

71753 20028-002 Santoprene check valve assembly(relief pump)

*Not shown

PARTS LIST FOR 2100 SERIES FLOJET PUMPS (MANUFACTURED AFTER SEPTEMBER 1989)

REPAIR KITS FOR 2000 SERIES PUMPSPART NO. REPLACES DESCRIPTION

70693* 21004-002 Cam/bearing kit

71747** 21010-002 Diaphragm kit Nitrile

71727*** 20028-086 Viton check valve kit(relief valve pump)

71728**** 20028-087 Viton check valve kit(demand switch pump)


Flojet Air Operated Diaphragm Pump

DESCRIPTIONFLOJET Industrial G-57 Series Pumps are designed for general commercial andindustial applications. These pumps are constructed from a selection of materials forhandling a broad range of chemicals.

Allowed fluids for Santoprene® materialsPotable Water, Acids Alkaline, Soaps Alcohols, KetonesNot Allowed Fluids for Santoprene® materialsOils, Solvents, Soaps with Solvents, D-Limonene, Aromatic Hydrocarbons

PERFORMANCE SPECIFICATIONSPUMPLiquid Temperature Min40°F (4.4°C)................................... Max ............ 120°F (48.9°C)Priming ....................... Dry ............... 15 ft. (4.5 m)................................... Wet .............. 20 ft. (6.1 m)Flow Rates .................. MaxUp to 5 GPM (18.9 L/min)Gas Supply Pressure ...... 20 to 100 PSI (1.4 to 6.9 bar)Noise Level ................... Max ........................... 87dB

FlexibleHose

Rigid Pipe PART NO. REPLACES

70261 G575205WARNING: DO NOT PUMPGASOLINE OR FLAMMABLE LIQUIDSOR USE WHERE FLAMMABLE VAPORS ARE PRESENT.

REF. NO. PART NO. REPLACES DESCRIPTION Qty.1A 70480 20740-050A Kit, Check Valve, Assy., Santo®,

Hastelloy 42A 70481 20730-000A Kit, Diaphragm, Santo&, w/O-Rings 23A 70482 20751-000A Kit, Shaft & Slide Valve Assy. (Santo®) 24 70483 20896-000A Kit, Flange & Housing Assy.w/O-Ring 25 70484 20753-000A Kit End Caps 26 70485 20793-100A Kit Hardware - Includes

Screws #10x1.5" Hi Low 14Retainer Clip Small 2Retainer Clip Large 2Exhaust Port 1Exhaust Muffler 1

7 70486 20132-000 Kit, Grommets 2

REPLACEMENT PARTS FOR G575205

Santoprene and Viton Material with 1/2" Ports

Flow in gpm (l/min) *Indicates airlet pressure

Pres

sure

in P

SI (

Bar

)

PRODUCT DATAPump Design .......................................... Duplex DiaphragmWetted Parts ..... Diaphragm Material Santoprene®......................... Check Valve Seat Material Santoprene®......................... Housing and check valve material......................................... Polypropylene (Glass Reinforced)......................... Springs ........................................ HastelloyPorts ................. Gas Inlet & Outlet ¼" (6.3 mm)Product Inlet 3/8" (9.5 mm)Product Outlet 3/8" (9.5 mm)Net Weight .......................................... 1.2 Pounds (0.54kg)® A registered trade mark of Monsanto Co.® A registered trade mark of I.E. DuPont Co.


F l o j e t S e n s o r V S D P u m p

KEY PART NO. MODEL #4515-743 PART NO. MODEL #4525-743 DESCRIPTION 00 70487 20409-043 70487 20409-043 Service Kit1 70488 20404-027 70489 20404-028 Upper Housing with Sensor Housing2 70695 20407-030 70695 20407-030 Check Valve Assembly3 70694 20403-040 70694 20403-040 Diaphragm Assembly (includes screws)4 70492 20419-002 70492 20419-002 Lower Housing Assembly5 70493 R2009-128A 70494 R2009-127A Motors with Sensor7 70495 20406-037A 70496 20406-038A Pump Head Assembly8 71742 20408-000 71742 20408-000 Side Clips (pair)

REPLACEMENT PARTS FOR SENSOR VSD PUMPS

PRODUCT FEATURES• Variable speed Drive

• Water Pressure System Pump

• Solid state proprietary micro controller

• Automatically adjusts to 12 or 24 V dc electrical systems

• Pressure regulated variable speed drive

• Hall effect pressure sensor - pat. pend.

• No switch, no points, no contacts

• Reduced current, extended life

• Saves energy at all flow rates

• CSA listed for US and Canadian sales

• EN ISO 8846 USCG Ignition Protection

• Space saving, eliminates accumulator tank

PART NO. REPLACES

70258 R4515743 70259 R4525743

FLOJET R4515/R4525SERIES SENSOR VSD WATER SYSTEMSStyles Available: Sensor VSD 3.7 Model No. R4515-743

0-3.7 gpm VSD Water Pressure SystemSensor VSD 4.5 Model No. R4525-7430-4.5 gpm VSD Water Pressure System

SHUT-OFF PRESSURER4515 35psi ............................. (2.4 bar)R4525 40 psi ............................ (2.8 bar)

SPECIFICATIONS (PATENT PENDING)Materials Pump Body ............................ Polypropylene

Diaphragm ............................. SantopreneValves .................................... EPDMSensor .................................... Magnetic Hall EffectVSD ....................................... PWM Solid State

TemperatureWater ..................................... 160°F (70°C) max

Thermal ProtectionMotor .................................... 266°F (130°C) max

DimensionsR4515 .................................... 3.75"H x 6.3W x 9.0"L(95mm x 160mm x 221 mm)R4525 .................................... 3.75"H x 6.3"W x 10.3"L(95mm x 160mm x 252mm)

Weight R4515 .................................... 4.3 lb/2.0 kgR4525 .................................... 6.3 lb / 3.0 kg

Flow R4515 .................................... 0-3.7 gpm / 14 lpmR4525 .................................... 0-4.5 gpm / 17 lpm

Running Pressure (see curves)R4515 .................................... 25 psi (1.7 bar)R4525 .................................... 30 psi (2.1 bar)


Flojet Model 4300 Series Parts List

REF PART NO. REPLACES DESCRIPTION

4 71722 11028-101 Baseplate assy. with grommet & screws

5 71723 20132-000 Grommet kit

8 71737 20552-000 Cam/bearing set screw

9 71746 20400-002 Cam/bearing kit with set screw

12 70694 20403-040 Diaphragm kit, santo with piston & screws


13 70695 20407-030 Check valve assy. kit EPDM with O-Ring& ferrules

14 70696 20404-001 Upper housing switch assy. kit

16 71741 20381-002 1/2" port hose barb

71742 20408-000 Port clip

71752 20132-005 Fan & shroud kit


70260 4401C-M12 12 volt motor driven 4 roller pump

FOR REPLACEMENT PARTS SEEDELAVAN 4 ROLLER PUMPBREAKDOWN ON PAGE 1-4.

For the smaller pumping jobs, where a tractor PTO is not available thepower to run this pump comes from the tractor’s 12 volt battery.

FEATURES• Pressure to 40 psi (276 kPa)• Capacity is 6.8 gpm (25.7 L/min) at 0 psi (0 kPa) or 4.1 gpm

(15.5 L/min) at 40 psi (275 kPa)• Draws 28.1 amperes at 40 psi (275 kPa)• Body and endplate – cast iron• Ball bearings – heavy-duty shielded bearings support shaft at

both ends. These sealed bearings are lubricated at the factoryfor the life of the pump

• Shaft – 1/2" hollow, 416 stainless steel• Rotor – corrosion resistant alloy• Rollers – 1/2" polypropylene• Seals – cartridge type, Viton lip seals• Ports – 3/4" NPT (F) side ports• Rotation – clockwise rotation when facing the motor shaft end• Mounting hole configuration interchanges with competitive unit

PRESSURE (PSI) FLOW RATE (GPM) AMPERES

0 6.8 13.3

5 6.5 15.1

10 6.5 17.0

15 5.8 18.8

20 5.4 20.7

25 5.1 22.5

30 4.7 24.4

35 4.4 26.2

40 4.1 28.1

DELAVAN ELECTRIC ROLLER PUMP


Shurflo 8000 Series Diaphragm Pumps

PART NO. MODEL DESCRIPTION PSI BAR GPM LPM AMPS

70290 8000-343-236 All Viton Pump 20 1.4 .93 3.5 3.91.2 gpm [4.5 lpm] open flow, all Viton elastomers 40 2.8 .84 3.2 4.960 psi [4.1 bar] Demand Switch, 3/8" NPT-Female ports. 60 4.1 .76 2.9 5.8

70287 8000-541-236 Lawn and Garden Pump 20 .89 .70 3.0 2.325 gallon [95 lt] tank or less, 1.0 gpm [3.8 lpm] open flow, 40 2.8 .70 2.6 3.2Viton valves, Santoprene diaphragm, 60 4.1 .62 2.3 3.860 psi [4.1 bar] Demand Switch, 3/8" NPT - Female ports.

70263 8000-542-136 Low Flow Standard Pump 20 1.4 1.11 4.3 4.11.2 gpm open flow, Viton® valves, Santoprene® diaphragm, 40 2.8 0.98 3.7 5.160 PSI Demand Switch, 1/2" MSPT* ports 60 4.1 0.90 3.4 6.0

70264 8000-542-296 Switch/Bypass Pump 20 1.4 1.18 4.5 3.71.3 gpm open flow, Viton® valves, 40 2.8 1.06 4.0 4.9Santoprene® diaphragm, 60 psi Internal Bypass, 60 4.1 0.90 3.4 5.9with 60 psi demand switch, 3/8" NPT-Female ports

70265 8000-543-136 Standard Pump 20 1.4 1.26 4.7 5.01.4 gpm open flow, Viton® valves, Santoprene® diaphragm, 40 2.8 1.14 4.3 6.260 PSI Demand Switch, 1/2" MSPT* ports. 60 4.1 1.02 3.9 7.3

70280 8000-543-236 Standard Pump 20 1.4 1.26 4.7 5.01.4 gpm [5.3 lpm] open flow, Viton valves, Santoprene diaphragm, 40 2.8 1.14 4.3 6.260 psi [4.1 bar] Demand Switch, 3/8" NPT - Female ports. 60 4.1 1.02 3.9 7.3

70289 8000-543-238 High Pressure Pump 20 1.4 1.45 5.5 4.21.4 gpm [5.3 lpm] open flow, Viton valves, Santoprene diaphragm, 40 2.8 1.31 5.0 5.5100 psi [6.9 bar] Demand Switch, 3/8" NPT - Female ports 60 4.1 1.22 4.6 6.5

100 6.9 0.96 3.6 8.7

70266 8000-543-936 Standard Pump w/Wire Harness 20 1.4 1.26 4.7 5.01.4 gpm open flow, Viton® valves, 40 2.8 1.14 4.3 6.2Santoprene® diaphragm, prewired with two wire molded 60 4.1 1.02 3.9 7.3connectors, 60 psi Demand Switch, 3/8" NPT-Female ports.

70267 8000-643-236 Transfer Pump 20 1.4 1.44 5.4 4.11.8 gpm open flow, Buna valves, Geolast® diaphragm 40 2.8 1.33 5.0 5.660 psi Demand Switch, 3/8" NPT-Female ports 60 4.1 1.22 4.6 6.8

70268 8006-543-236 Standard Pump w/Reversed Pump Head 20 1.4 1.26 4.7 5.01.4 gpm open flow, Viton® valves, Santoprene® diaphragm 40 2.8 1.14 4.3 6.260 psi Demand Switch, 3/8" NPT -Female ports 60 4.1 1.02 3.9 7.3

70288 8007-543-236 Standard Pump w/Electrical Package** 20 1.4 1.57 5.9 4.31.4 gpm [5.3 lpm] open flow, Viton valves, Santoprene diaphragm, 40 2.8 1.39 5.3 5.660 psi [4.1 bar] Demand Switch with built-in on/off power 60 4.1 1.23 4.7 6.8switch, fuse holder, prewired with two wire molded connector andmotor shroud, 3/8" NPT - Female ports.

70291 8030-813-239 150 psi High Pressure Pump 80 5.5 .94 3.5 4.61.5 gpm [5.7 lpm] open flow, Viton valves, Santoprene diaphragm, 100 6.9 .86 3.2 6.3150 psi [10.3 bar] Demand Switch, 3/8" NPT - Female ports. 150 10.2 .61 2.3 7.5

AUTOMATIC DEMAND 12 VDCFeatures• Self priming up to 8 feet [2.4m]• Chemical resistant material• Designed for heavy duty spraying and fluid transfer applications• Can run dry without damageAdditional features of pump with Elect. Pkg.**• Built in on/off switch included• In-line fuse assembly providedThe 8000 Series diaphragm pump is Shurflo’s most widely used agriculturepump. With its conical shaped viton valves and automatic demand switch. The8000 Series pump is the pump of choice for sprayers used on the farm or aroundthe yard. These 12 VDC pumps deliver up to 1.4 gpm [5.3 lpm]providing maximum performance in a wide range of applications

SEE PAGE 1-81 FOR PARTS BREAKDOWN

ELECTRICAL PKG.PART NO. SPP 71759


8 0 0 0 S e r i e s D i a p h r a g m P u m p s

BY-PASS 12 VDC


70281 8000-543-250 Standard By-Pass Pump 20 1.4 1.20 4.5 3.91.4 gpm [5.3 lpm] open flow, Viton valves, Santoprene diaphragm, 40 2.8 1.10 4.2 5.245 psi [3.1 bar] internal by-pass, 3/8" NPT - Female ports 60 4.1 1.00 3.8 6.2

70284 8007-543-850 By-Pass Pump w/Elect. Pkg.** 20 1.4 1.20 4.5 3.9used on all 1.4 gpm [5.3 lpm] open flow, Viton valves, Santoprene diaphragm, 40 2.8 1.10 4.2 5.2Westward 60 psi [4.1 bar] internal by-pass with built-in on/off switch, 60 4.1 1.00 3.8 6.2sprayers Prewired w/2-wire molded connector and motor shroud,

3/8" NPT - Female ports.

70269 8006-543-250 Bypass Pump w/Reserved Pumphead 20 1.4 1.30 4.9 4.01.4 gpm open flow, Viton® valves, Santoprene® diaphragm, 40 2.8 0.69 2.6 5.260 psi internal bypass with built-in on/off switch, 50 4.1 0.18 0.7 5.5Fuse holder, Prewired w/2-wire molded connector and motorshroud. No Demand Switch, 3/8" NPT-Female ports.

Features• Self priming up to 8 feet [2.4 m]• Chemical resistant materials• Internal bypass• Can run dry without damageAdditional features of pump with Elect. Pkg.**• Built in on/off switch included• In-line fuse assembly providedThese Shurflo internal bypass pumps are the answer to applications where anautomatic demand switch is not required. Pumps with by-pass will continue to runat high pressure. Ideal for intermittent duty applications. They incorporate a triplechamber with viton elastomers to withstand the toughest of applications. Perfectfor spot sprayers, foam markers and transfer applications where smooth consist-ent flow is needed



70292 2088-313-145 Premium Pump with Fin Cooled Motor 10 0.7 3.09 11.7 6.43.6 gpm [13.6 lpm] open flow, Viton valves, Santoprene diaphragm 30 2.1 2.49 9.4 8.745 psi [3.1 bar] Demand Switch, 1/2" MSP ports, Continuous duty 50 3.4 1.90 7.2 10.1

70282 2088-343-135 Standard Pump 10 0.7 2.80 10.6 5.33.0 gpm [11.3 lpm] open flow, Viton valves, Santoprene diaphragm, 30 2.1 2.36 8.9 6.745 psi [3.1 bar] Demand Switch, 1/2" MSP ports. 50 3.4 1.42 5.4 8.0

70317 2088-474-144 Standard Pump, 24V 3.0 gpm open flow, Viton valves, Santoprenediaphragm, 45 psi [3.1 bar] Demand Switch,1/2" MSP Parts

2088 SERIES DIAPHRAGM PUMPSAUTOMATIC DEMAND 12V DCFeatures•Self Priming up to 12 feet [3.7 m]•Can run dry without damage•Built-in check valve (may vary on models) prevents back flow of fluid into the solution tank•Continuous duty motor (fin cooled version only)•Chemical resistant materials•Automatic demandShurflo 2088 Series diaphragm pumps are considered to be the workhorse ofpumps. They are used in a variety of spot spraying, mini-bulk transfer andfertilizer applications that require flows of up to 3.6 gpm [13.6 lpm]. They areavailable in a variety of chemical resistant materials


PREMIUM

STANDARD

STANDARD BY-PASS

ELECTRICAL PKG.PART NO.71759ROCKER SWITCHPART NO. 71758

BY-PASSW/ELECT. PKG.


S h u r f l o P o w e r T w i n P u m p ™

POWER TWIN PUMPPOWER TWIN PUMPPOWER TWIN PUMPPOWER TWIN PUMPPOWER TWIN PUMPTMTMTMTMTM

"FIRST IN FL"FIRST IN FL"FIRST IN FL"FIRST IN FL"FIRST IN FLUID INNOUID INNOUID INNOUID INNOUID INNOVVVVVAAAAATION"TION"TION"TION"TION"

SHURFLSHURFLSHURFLSHURFLSHURFLO IS PLEASED TO OFFER OUR NEWO IS PLEASED TO OFFER OUR NEWO IS PLEASED TO OFFER OUR NEWO IS PLEASED TO OFFER OUR NEWO IS PLEASED TO OFFER OUR NEWTWIN-HEAD HIGH FLTWIN-HEAD HIGH FLTWIN-HEAD HIGH FLTWIN-HEAD HIGH FLTWIN-HEAD HIGH FLOW PUMP!OW PUMP!OW PUMP!OW PUMP!OW PUMP!For over a decade Shurflo’s 2088 Series family ofpumps has proven reliable, durable and powerfulperformance in a wide range of applications.• Self priming• Up to 7 gpm• 45 psi pressure setting• Splash-proof switch

GREAT FOR PROPORTIONING FLUIDS• Low AMP draw• Optional manifold system• Quiet/balanced operation• Long life premium motor

PART NO. MODEL # DESCRIPTION

70315 4111-035 12 VDC with heat sink, Viton valves, Santoprene diaphragm, splash-proof switch, 45 psi with manifold

70316 4211-035 12 VDC with heat sink, Viton valves, Santoprene diaphragm, splash-proof switch, 45 psi, no manifold

TYPICAL PERFORMANCEPRESSURE FLOW CURRENT VOLTAGE(PSI/BAR) (GPM/LPM)

OPEN 7.0/26.5 9.8 12 VDC

10/0.7 6.4/24.2 12.8 12 VDC

20/1.4 5.8/22.0 15.2 12 VDC

30/2.1 5.0/18.7 17.1 12 VDC

40/2.8 4.2/16.0 19.1 12 VDC


8000 and 8020 Series Diaphragm Pumps

AUTOMATIC DEMAND 115V AC


70286 8000-033-236 All Viton Pump 20 1.4 .89 3.4 .401.0 gpm [3.8 lpm] open flow, Viton valves, Viton diaphragm 40 2.8 .76 2.9 .4860 psi [4.1 bar] demand switch, 3/8" NPT - female ports 60 4.1 .64 2.4 .54

70294 8000-533-236 Standard Pump 20 1.4 1.15 4.3 .461.4 gpm [5.3 lpm] open flow, Viton valves, Santoprene diaphragm, 40 2.8 .97 3.7 .5560 psi [4.1 bar] demand switch, 3/8" NPT - female ports 60 4.1 .85 3.2 .64

70304 8020-513-236 Standard pump with 6' [1.8 m] Power Cord 10 0.7 1.26 4.8 .411.4 gpm [5.3 lpm] open flow, Viton valves, Santoprene diaphragm, 20 1.4 1.15 4.3 .4660 psi [4.1 bar] demand switch, 3/8" NPT - female ports, Polypro parts 30 2.1 1.05 4.0 .51

40 2.8 .97 3.7 .5550 3.4 .91 3.4 .6060 4.1 .85 3.2 .64

70293 8020-833-238 High Pressure Pump with 6' [1.8 m] Power Cord 10 0.7 1.35 5.1 .461.4 gpm [5.3 lpm] open flow, Viton valves, Santoprene diaphragm, 20 1.4 1.26 4.8 .51100 psi [6.9 bar] demand switch, 3/8" NPT - female ports, Nylon parts 30 2.1 1.17 4.4 .56

40 2.8 1.10 4.2 .6150 3.4 1.05 4.0 .6560 4.1 1.00 3.8 .7070 4.8 .96 3.6 .7480 5.5 .93 3.5 .7890 6.2 .89 3.4 .82

100 6.9 .85 3.2 .85

70296 8030-863-239 150 psi High Pressure Pump 80 5.5 .94 3.5 .761.5 gpm [5.7 lpm] open flow, Viton valves, Santoprene diaphragm, 100 6.9 .86 3.2 .86150 psi (10.3 bar) demand switch 3/8" NPT female ports 150 10.2 .61 2.3 1.00

Features• Self priming up to 8 feet [2.4 m]• Chemical resistant materials• Can run dry without damage• Built-in check valve• Corded pump optionalThese Shurflo 8000 and 8020 Series Demand pumps provide the same reliabil-ity as the 12 VDC version except in a 115 VAC capacity. They are ideal inagricultural applications that require high pressure with flow rates up to 1.4gpm [5.3 lpm] with low amp draw. They can be mounted in any position, arecompact, and are designed for long trouble free life.


8000 AND 8020 SERIES DIAPHRAGM PUMPS

BY-PASS 115 VAC


70305 8020-503-250 By-pass pump with 6 ft. power cord. 10 0.7 1.36 5.1 .341.4 gpm [5.3 lpm] open flow, Viton valves, Santoprene diaphragm, 20 1.4 1.21 4.6 .4145 psi [3.1 bar] internal by-pass, 3/8" NPT - female ports, nylon parts 30 2.1 1.05 4.0 .46

40 2.8 .65 2.5 .5150 3.4 .19 0.7 .54


2 0 8 8 S e r i e s D i a p h r a g m P u m p s

Features• Self Priming up to 12 feet [3.7 m]• Can run dry without damage• Built-in check valve (may vary on models) prevents back flow of fluid into the solution tank• Chemical resistant materials• Automatic demandShurflo 2088 Series diaphragm pumps are considered to be the workhorse of pumps. They are usedin a variety of spot spraying, mini-bulk transfer and fertilizer applications that require flows of up to 3.6gpm [13.6 lpm]. They are available in a variety of chemical resistant materials



70310 2088-394-144 Standard Pump with Power Cord 10 0.7 2.40 9.1 .553.0 gpm [11.4 lpm] open flow, Viton valves, Santoprene diaphragm, 30 2.1 1.90 7.2 .6545 psi [3.1 bar] Demand Switch, 1/2” MSP ports 50 3.4 1.40 5.3 .75

70295 2088-394-154 Standard Pump 10 0.7 2.71 10.2 .653.2 gpm [12.1 lpm] open flow, Viton valves, Santoprene diaphragm, 30 2.1 2.10 8.0 .8940 psi [2.8 bar] demand switch, 1/2” MSP ports 50 3.4 1.59 6.0 1.04


70297 166-200-36 Viton Air Pump 2.0 gpm [7.6 lpm] open flow, Viton valves and diaphragm

70298 166-200-46 Buna Air Pump 2.0 gpm [7.6 lpm] open flow, Buna valves and diaphragm

70299 166-200-56 EPDM Air Pump 2.0 gpm [7.6 lpm] open flow, EPDM valves and diaphragm

70300 166-200-57 Santoprene Air Pump 2.0 gpm [7.6 lpm] open flow, Santo valves and diaphragm

1 6 6 S e r i e s D i a p h r a g m P u m p s

AIR DRIVENFeatures• 2 chamber dual diaphragm• On demand operation• 30 to 60 psi [2.1 - 4.1 bar]• Positive displacement• Chemical resistant polypropylene bodyShurflo’s 166 Air Operated Demand Pumps employ a dual diaphragm design, with a patented fast action switching mechanism allowingfor consistent flow and pressure. They are built for the toughest pumping applications and are available in a variety of elastomersthat allow them to be compatible with most caustic or acidic fluids. Ideal for chemical transfer, liquid fertilizer injection and agriculturalsprayers.

9 4 S e r i e s P r o p o r t i o n i n g P u m p s

PART NO. MODEL DESCRIPTION PSI BAR GPM LPM

70302 94-260-21 Water Driven Proportioning Pump 20 1.4 1.15 4.33:1 ratio, 3.0 gpm [11.4 lpm] open flow, EPDM seals and valves, 40 2.8 .97 3.7Santoprene diaphragm, 50 psi [3.4 bar], 3/8" barb fittings

70303 94-260-22 Water Driven Proportioning Pump 20 1.4 .89 3.45:1 ratio, 3.2 gpm [12.1 lpm] open flow, EPDM seals and valves, 40 2.8 .76 2.9Santoprene diaphragm, 50 psi [3.4 bar], 3/8" barb fittings

The Brix Pump is a proportioning device which pumps two liquids (e.g. water and concen-trate) in an exact ratio. The particular ratio is determined in the pump, and is thereby maintainedprecisely, independent of system flow or pressure changes, with no need to set or regularlyreadjust brix at the discharge point.The pump operates on the source pressure of one of the proportioned liquids, typicallyincoming water, eliminating the need for CO2 pressurized air or electric power.

AUTOMATIC DEMAND 115 VAC


402 Series Midi-Fram Pumps 12 VDC


70308 402-140-033 Standard Light Duty Transfer Pump 0 0.0 .75 2.8 1.6.75 gpm [2.8 lpm], Viton valves, Santoprene diaphragm, 10 0.7 .60 2.3 2.5Nylon, 30 psi [2.1 bar] switch, 3/8" barb ports, with Heat Sink 25 1.7 .50 1.9 2.7

70309 402-040-000 Light Duty Transfer Pump w/Santoprene Elastomers 0 0.0 .50 1.9 1.2.50 gpm [1.9 lpm], Santoprene elastomers, Nylon, no switch, 10 0.7 .40 1.5 1.43/8" barb ports, without Baseplate or Heat Sink. 25 1.7 .30 1.1 1.7

Features• Self-priming up to 4 feet [1.2 m]• Can be run dry without damage• Chemical resistant construction• Available in 12 VDCShurflo’s Model 402 Series is ideal for light duty applications requiring moderatepressure with flow rates up to 0.75 gpm(2.8 lpm) with low amp draw. Availablewith Santoprene or Viton valves and Santoprene diaphragm, the 402 Series canaccommodate a wide range of chemicals typically found in agriculture.

SLV Series Demand Pump 12VDC

Features• Automatic demand; 25 PSI (1.72 bar) on /40 PSI (2.76 bar) off• Self priming up to 2.5 vertical feet (.76 m)• Long life pressure switch• Santoprene® diaphragm, Viton® valves• Thermally protected ball bearing motor with splashproof housing• Internal fan radiates heat; external heat sink not required• Integral on/off switch optionalNew from Shurflo, the SLV is an economy spot sprayer pump forlow volume intermittent duty applications. Unique design has nometals in the fluid path for maximum chemical resistance. Bigpump features include automatic demand operation andeleastomers that handle a wide variety of chemicals. Perfect for lowvolume spraying and transfer. Cost effective yet with highperformance and reliability; the SLV offers tremendous value.


70270 SLV10-AA40 Automatic Demand Pump 3 0.2 0.9 3.4 1.81.0 GPM open flow, Viton® valves 10 0.7 0.73 2.8 2.1Santoprene® Diaphragm 20 1.4 0.62 2.3 2.340 PSI Demand Switch, 3/8" Barb Ports 30 2.1 0.49 1.9 2.5Integral on/off switch included

70271 SLV10-AA41 Automatic Demand Pump 3 0.2 0.9 3.4 1.81.0 GPM open flow, Viton® valves 10 0.7 0.73 2.8 2.1Santoprene® Diaphragm 20 1.4 0.62 2.3 2.340 PSI Demand Switch, 3/8" Barb Ports 30 2.1 0.49 1.9 2.5

SLV10-AA40 includes on/off switch

WITH BASEPLATEAND SWITCH

WITHOUT BASEPLATEOR SWITCH


9300 Series Submersible Pump 24 VDC

Features• Accommodates for wells 4 inches

[10.2 cm] in diameter and larger• Accepts a variety of jacketed cables

from your power source• Runs dry without damage• Corrosion-proof housing with stainless-

steel fasteners• Long-life, 24 VDC operation• Quick Disconnect for easy installation

and service

VERT. LIFT SOLAR ARRAY CURRENTSPART NO. MODEL DESCRIPTION FT METER GPH LPH WATTS AMPS

70301 9325-043-101 1.8 gpm [6.8lpm] open flow, EPDM valves, 20 6.1 117 443 58 1.5Santoprene diaphragm 60 18.3 109 413 78 2.1Net weight - 6 lbs. 100 30.5 103 390 99 2.6

140 42.7 99 375 115 3.1180 54.9 93 352 135 3.6230 70.1 82 310 155 4.1

A solution to your remote water needs,Shurflo’s 9300 Series Submersible Pump!It’s rugged, durable and built to last. Thispump delivers a steady 82 gph (310 lph)operating @ 100 psi [6.9 bar] maximumdepth of 230 feet (70.1 m). It incorporatesa unique waterblocked cable connectorthat is impervious to water leakage andcondensation problems preventingwaterwicking. Great for applications inlivestock watering, irrigation, ponds,islands, remote homes and cabins.

Features• Self-priming to 7 1/2 feet [2.3 m] vertical• Maximum head of 40 feet [12.2 m] (12 psi)

[.83 bar]• Liquid temps from 40°F to 185°F [4.4°C to

85°C]• Thermal overload protection• Stainless steel shaft• BUNA-N impeller and lip seal• Built-in reversible switch and 8 foot [2.4 m]

cable with battery clips (3000-350 only)

A variety of uses for these pumps has beenmade possible by the use of a buna impellerfor applications in pumping water tochanging oil in cars, trucks, farm equipmentand center point irrigation systems. Pumpsincorporate thermal overload protection.The premium model includes a built-in3 position switch to simplify flow reversal.

Not intended for use with flammable liquids, or in flammable environments.

DISCHG. FT. CURRENTPART NO. MODEL DESCRIPTION PSI BAR OF HEAD GPM LPM (AMPS)

70311 3000-050 Standard 0 0.00 0.0 3.75 14.2 6.55 0.34 11.5 3.40 12.9 7.1

10 0.69 23.0 2.50 9.5 7.4

70312 3000-350 Premium 0 0.00 0.0 3.75 14.2 6.55 0.34 11.5 3.40 12.9 7.1

10 0.70 23.0 2.50 9.5 7.4

3000 Series Flexible Impeller Pumps 12VDC

STANDARD3000-050

PREMIUM3000-350


D r i l l P u m p

PART NO. MODEL PORTS FLOW - OPEN LPH

70313 3010-000 3/4" (M) GHT ports 200 gph 757

Features• Self-primes to 8 feet [2.4 m] vertical• Pump liquids 40°F to 120°F [4.4°C to 48.8°C]• BUNA impeller and seals• 1/4" [6.35 mm] shaft fits standard drills

Attaches to any standard 1/4" [6.35 mm] drill motor. Ideal for pumping water from appliances,aquariums, water beds, sinks, toilets or drums. Includes a 1/4" [6.35 mm] oil probe that easilyallows the transfer of oil from cars, trucks or lawn and farm engines and equipment.

Not intended for use with flammable liquids, or in flammable environments.

Features• Complete with necessary tub-

ing and oil storage container• Built-in reversible switch and

eight foot cable with batteryclips

• Thermal overload protection• BUNA-N impeller

Makes a messy job clean and easy. Simply install the oil probein the engine oil dipstick tube, attach the battery clips, and flip aswitch. Oil is safely removed and stored in the easy to carrycontainer.

PART NO. MODEL PORTS

70314 3000-400 3/4" M garden hose, 3/8" NPT - female

O i l C h a n g e S y s t e m


A c c e s s o r i e s

Twist-on In-line strainersThese twist-on strainers will protect thepumps filtering dirt and other foreignparticles often found in tanks used inag spraying. Mounts directly onpumphead using integral molded-inthreads. Their transparent designmakes it easy to see when it’s time toclean out the strainer. A simple twistof the wrist opens the strainer - notools required.


70283 181-101 Accumulator Tank24 ounce total capacity (liquid and air), pre-pressurized to 20 psi [1.8 bar],(0 to 100 PSI [6.9 bar] range of adjustment), Santoprene bladder, mountingbracket, 1/2" (F) NPT ports

Twist-on Water Strainer71866 170-060-00 316 ss, 50 mesh screen, 1/2" [12 mm] Barb inlet, EPDM O-Ring.71867 170-061-00 316 ss, 50 mesh screen, 1/2" [12 mm] Pipe inlet, EPDM O-Ring

Additional fitting p/n 73454 needed for use with 8000 series pumps with 3/8"NPT - female ports

ACCUMULATORTANK

73454

TWIST-ON WATER STRAINER

Swivel Barbed Straight With Wingnut


71869 8-071-01 1/2" NPT - female x 3/8" barb*

71870 8-070-01 1/2" NPT - female x 1/2" barb*

71871 8-154-01 1/2" NPT - female x 5/8" barb

71872 8-156-01 1/2" NPT - female x 3/4" barb

71873 8-161-01 1/2" NPT - female x 1/2" barb

71874 8-162-01 1/2" NPT - female x 3/8" barb

*Swivel only


71875 8-034-01 1/2" NPT - female x 1/2" barb*

71876 8-065* 1/2" NPT - female x 1/2" NPT male*

71877 8-060-01 1/2" NPT - female x 3/8" barb*

71878 8-157-01 1/2" NPT - female x 3/4" barb

71879 8-155-01 1/2" NPT - female x 5/8" barb

71880 8-158-01 1/2" NPT - female x 1/2" barb

71881 8-159-01 1/2" NPT - female x 3/8" barb

*Swivel only

Swivel Barbed Elbow With Wingnut

71866

71867


8 0 0 0 S e r i e s P a r t s K i t L i s t

1 2 3A 3B 4 5A 5B 6 7 8COMPLETE CHECK BY-PASS DRIVE

PUMP PUMP PUMP HEAD SWITCH VALVE UPPER NON BY-PASS DIAPHRAGM IMPELLERPART NO. MODEL NO. ASSEMBLY ASSEMBLY ASSEMBLY HOUSING VALVE ASSEMBLY ASSEMBLY ASSEMBLY MOTOR

70286 8000-033-236 94-380-05 94-375-05 94-374-10 94-379-00 94-390-05 94-395-06 94-385-04 11-150-0071882 71760 71883 71761 71762 71764 71776 71884

70290 8000-343-236 94-380-05 94-375-05 94-374-10 94-379-00 94-390-05 94-395-05 94-385-04 11-111-0071882 71760 71883 71761 71762 71885 71776 71766

70294 8000-533-236 94-380-02 94-375-05 94-374-10 94-379-00 94-390-05 94-395-06 94-385-03 11-150-0071767 71760 71883 71761 71762 71764 71765 71884

70287 8000-541-236 N/A 94-375-06 94-374-05 94-379-00 94-390-05 94-395-06 94-385-02 11-148-0471886 71779 71761 71762 71764 71925 71887

70280 8000-543-236 94-380-02 94-375-06 94-374-05 94-379-00 94-390-05 94-395-06 94-385-03 11-111-0071767 71886 71779 71761 71762 71764 71765 71766

70289 8000-543-238 N/A 94-375-18 94-374-05 94-379-00 94-390-05 94-395-06 94-385-03 11-111-0071888 71779 71761 71762 71764 71765 71766

70281 8000-543-250 94-382-09 N/A N/A 94-379-00 94-391-09 94-395-06 94-385-03 11-111-0071768 71761 71763 71764 71765 71766

70288 8007-543-236 94-380-02 94-375-06 94-374-05 94-379-00 94-390-05 94-395-06 94-385-03 11-184-0071767 71886 71779 71761 71762 71764 71765 71889

70284 8007-543-850 N/A N/A N/A 94-379-00 94-391-07 94-395-06 94-385-03 11-168-0171761 71777 71764 71765 71778

70305 8020-503-250 94-382-09 N/A N/A 94-379-00 94-391-08 94-395-06 N/A 11-194-0071768 71761 71890 71764 71891

70304 8020-513-236 94-380-02 94-375-06 N/A 94-379-00 94-390-05 94-395-06 N/A 11-194-0171767 71886 71761 71762 71764 71892

70293 8020-833-238 94-380-28 94-375-15 N/A 94-379-01 94-390-15 94-395-16 N/A 11-195-0171893 71894 71895 71896 71897 71898

70291 8030-813-239 N/A 94-375-15 N/A 94-379-01 94-390-15 N/A N/A 11-227-0071894 71895 71896 71899

70296 8030-863-239 N/A 94-375-15 94-374-10 94-379-01 94-390-15 N/A N/A 11-223-0071894 71883 71895 71896 71900

71758 Rocker switch only 10-360 fits Pump No. 70284

71759 Complete electric pkg c/w rocker switch 84-712-00 fits Pump No. 70284

used on all Westward Sprayers

71758

71759


2 0 8 8 S e r i e s P a r t s K i t L i s t

1 2 3 4 5 6 7DRIVE

COMPLETE CHECK BY-PASS IMPELLERPUMP PUMP PUMP HEAD SWITCH VALVE UPPER NON BY-PASS DIAPHRAGMPART NO. MODEL NO. ASSEMBLY ASSEMBLY ASSEMBLY HOUSING VALVE ASSEMBLY ASSEMBLY MOTOR

70292 2088-313-145 94-236-15 94-230-55 94-237-05 94-231-30 94-232-05 94-238-03 11-185-0671769 71901 71773 71770 71774 71775 71902

70282 2088-343-135 94-231-05 94-230-36 94-237-05 94-231-30 94-232-05 94-238-03 11-111-0071772 71771 71773 71770 71774 71775 71766

70310 2088-394-144 94-231-05 94-230-36 94-237-05 94-231-30 94-232-05 94-238-03 11-195-0171772 71771 71773 71770 71774 71775 71898

70295 2088-394-154 94-231-05 94-230-36 94-237-05 94-231-30 94-232-05 94-238-03 11-150-1071772 71771 71773 71770 71774 71775 71904

94-231-05 Upper housing with switch kit to fit pump numbers 70282, 70310 and 70295 (includes71772 ref #2, 3 and 4)


M o n a r c h S u m p & S e w a g e S u b m e r s i b l e E f f l u e n t P u m p s

SUBMERSIBLE EFFLUENT PUMPS - AUTOMATIC AND MANUALSOLIDS SHIP WT. CORD

MODEL NO PART NO. HP VOLT PH HANDLING (LBS.) SWITCH LENGTH

WS30M 620010 1/3 115V 1 11/16" 51 Manual 20'

WS30AM 620000 1/3 115V 1 11/16" 53 Automatic 20'

HIGH HEAD SUBMERSIBLE EFFLUENT PUMPS - AUTOMATIC AND MANUALWS50HM 620200 1/2 115V 1 3/4" 57 Manual 30'

WS50HM-20 620218 1/2 115V 1 3/4" 56 Manual 20'

WS50HAM 620212 1/2 115V 1 3/4" 59 Automatic 30'

WS50HAM-20 620219 1/2 115V 1 3/4" 58 Automatic 20'

WS50HM-12 620204 1/2 208/230V 1 3/4" 57 Manual 30'

WS50HM-12-20 620220 1/2 208/230V 1 3/4" 56 Manual 20'

WS50HAM-12 620217 1/2 208/230V 1 3/4" 59 Automatic 30'

WS50HAM-12-20 620221 1/2 208/230V 1 3/4" 58 Automatic 20'

WS100HM-12 620201 1 208/230V 1 3/4" 58 Manual 30'

WS100HM-12-20 620222 1 208/230V 1 3/4" 57 Manual 20'

WS100HAM-12 620213 1 208/230V 1 3/4" 60 Automatic 30'

WS100HAM-12-20 620223 1 208/230V 1 3/4" 59 Automatic 20'

WS100HM-32 620207 1 208/230V 3 3/4" 62 Manual 30'

WS100HM-34 620206 1 460V 3 3/4" 62 Manual 30'

Note: Manual models do not include float switch. Automatic models include float switch.

WS SERIES SUBMERSIBLE EFFLUENT PUMPSAutomatic, Manual, and High Head Effluent Pumps.Features.1. Construction - Motor and pump housing is Cast Iron Class 30.2. Cord - Power cord sealed at motor housing. WS50 and WS100

uses SJOW. WS30 uses SJTW.3. Impeller - Cast Iron Class 30. Solids handling non-clog impeller.

Two vanes on the WS50 and WS100. Three vanes on the WS30.4. Seal - Mechanical carbon/ceramic type 6, 5/8 rotary.5. Shaft - Motor shaft is 416 stainless steel.6. Motor - Oil filled chamber with automatic overload protection,

double ball bearing. Capacitor Start designed for hi-torqueand are thermally protected with automatic reset (single phaseonly).

7. Switch - Mercury Free float switch for automatic on-offoperation; piggyback style

8. Discharge - 2" NPT. Adaptor kit for 3" NPT available9. Fasteners - Stainless steel fasteners throughout, for service-

ability.

PERFORMANCE CHARTSTOTAL HEAD IN FEET SHUT-OFF

5 10 15 20 25 HEADMODEL NO. RPM CAPACITIES IN U.S. GPM (FT.)

WS30 1750 105 90 70 45 15 28

TOTAL HEAD IN FEET SHUT-OFFHIGH HEAD 10 20 30 40 50 60 70 80 90 HEADMODEL NO. RPM CAPACITIES IN U.S. GPM (FT.)

WS50H 3450 115 98 78 57 30 0 60

WS100H 3450 150 140 128 115 97 76 53 27 0 90


M o n a r c h S u m p & S e w a g e S u b m e r s i b l e E f f l u e n t P u m p s

SOLIDS SHIP WT. CORDMODEL NO PART NO. HP VOLT PH HANDLING (LBS.) SWITCH LENGTH

WS41M 620011 4/10 115 1 7/8" 53 Manual 20'

WS41AM 620001 4/10 115 1 7/8" 55 Automatic 20'

WS51M 620012 1/2 115 1 1 3/8" 55 Manual 20'

WS51AM 620002 1/2 115 1 1 3/8" 57 Automatic 20'

WS52M 620013 1/2 115 1 2" 57 Manual 20'

WS52AM 620003 1/2 115 1 2" 59 Automatic 20'

WS102M-12 620203 1 208/230 1 2" 62 Manual 20'

WS102M-12 620215 1 208/230 1 2" 64 Automatic 20'

WS102M-32 620208 1 208/230 3 2" 63 Manual 20'

WS102M-34 620209 1 460 3 2" 63 Manual 20'

WS SERIES SUBMERSIBLE SEWAGE PUMPSAutomatic and Manual Sewage PumpsFeaturesConstruction - Motor and pump housing is Cast Iron Class 30.Cord - Power cord sealed at motor housing. WS102 uses SJOW. WS41, WS51, and WS52uses SJTW.Impeller - Cast Iron Class 30. Two vane solids handling non-clog impeller.Seal - Mechanical carbon/ceramic type 6, 5/8 rotary.Shaft - Motor shaft is 416 stainless steel.Motor - Oil filled chamber with automatic overload protection, double ball bearing.Capacitor Start designed for hi-torque and are thermally protected with automatic reset(single phase only).Switch - Mercury Free float switch for automatic on-off operation; piggyback style.Discharge - 2" NPT. Adapter kit for 3" NPT available.Fasteners - Stainless steel fasteners throughout, for serviceability.

SUBMERSIBLE EFFLUENT PUMPS - AUTOMATIC AND MANUAL

SpecificationsSUBMERSIBLE EFFLEUNT SUBMERSIBLE SEWAGE

MODELS WS30 WS50H WS100H WS41 WS51 WS52 WS102

Height 13.75" 15.10" 15.10" 14.63" 15.75" 16.50" 17.80"

Min. Dia. 14" 18" 18" 14" 14" 14" 18"

Max. Depth 28' 60' 90' 26' 27' 23' 37'

Discharge 2" NPT 2" NPT 2" NPT 2" NPT 2" NPT 2" NPT 2" NPT

Cut-in Height 16" 17" 17" 17" 17" 17" 18"

Cut-out Height 8" 8" 8" 8" 8" 8" 8"

Adjustable Yes Yes Yes Yes Yes Yes Yes

Performance ChartsMODEL RPM TOTAL HEAD IN FEET SHUT-OFFNO 5 10 15 20 25 30 35 HEAD

CAPACITIES IN U.S. GPM (FT.)

WS41 1750 118 95 70 40 8 53

WS51 1750 155 120 83 52 14 27

WS52 1750 135 90 47 14 23

WS102 1750 175 149 118 85 46 16 37

WS102AM-12


Monarch Sump & Sewage Sump Pumps

Features:Motor - 1/6 HP, 115 volt, thermal overload protected. 9 foot power cord. Stainless steel heattreated shaft. “Oil free” motor. Permanently lubricated lip seal. CSA approved.Pump Casing - Corrosion resistant aluminum for superior heat dissipation.3/4" NPT discharge.Impeller - Constructed of durable glass reinforced thermoplastic.Garden Hose Adapter - For convenient hook up.Bottom Suction Design - Bottom suction design allows pumping to within 1/4" of the surface. Built in suction strainer to eliminate internal damage from possible debris.Removable filter screen for easy cleaning.

UP16M SERIES SUBMERSIBLE UTILITY PUMP

PERFORMANCE CHARTSMODEL TOTAL HEAD IN FEET SHUT-OFFNO 5 10 15 17 HEAD


UP16M 20 14 7 4 16

SUBMERSIBLE UTILITY PUMP - 3/4” DISCHARGEMODEL NO ORDER NO. HP SHIP WT. DESCRIPTION

(LBS.)

UP16M 620137 1/6 8 Submersible utility pump with garden hose adapter44-33FR 616130 1/3 33 Cast Iron Pump end with S.S. Franklin Motor built-in44-50FR 616130 1/2 37 Pressure diaphragms with 10 ft. vented power cord

UP16M SERIES SUBMERSIBLE UTILITY PUMPFeatures:Motor - 1/4 HP, 115 volt, thermal overload protected. 9 foot power cord. Stainless steel heattreated shaft. “Oil free” motor. Permanently lubricated lip seal. CSA approved.Pump Casing - Corrosion resistant aluminum for superior heat dissipation. 1 1/4" NPT dis-charge.Impeller - Constructed of durable glass reinforced thermoplastic.Switch - Automatic, mercury free, mechanical float switch.Bottom Suction Design - Bottom suction design allows pumping to within 1/4" of the sur-face. Built in suction strainer to eliminate internal damage from possible debris. Removablefilter screen for easy cleaning.



SP25A 24 19 12 5 21

SUBMERSIBLE UTILITY PUMP - 1 1/4” DISCHARGEMODEL NO ORDER NO. HP SHIP WT. DESCRIPTION

(LBS.)

SP25A 620136 1/4 8.5 Submersible sump pump with automatic float switch.

SP33A 620135 1/3 10 Submersible sump pump with automatic float switch


Monarch Sump & Sewage Sump/Effluent Pumps

SP33A SERIES SUBMERSIBLE SUMP PUMPFeatures:Motor - 1/3 HP, 115 volt, thermal overload protected, CSA approved. “Oil free” motor. Stain-less steel motor housing improves heat dissipation for longer motor life. Complete with a 9foot power cord. Stainless steel heat treated shaft. Permanently lubricated lip seal.Pump Casing - Fully constructed of durable reinforced thermoplastic for excellent corrosionresistance. 1 1/4" NPT discharge for ease of installation.Impeller - Non clogging design constructed of durable reinforced thermoplastic.Switch - Automatic, mercury free, mechanical float switch.Bottom Suction Design - Built in suction strainer to eliminate internal damage from possibledebris. Removable filter screen for easy cleaning.

Features:Construction - Rugged cast iron motor housing dissipates heat away from motor. Ruggedcorrosion resistant, molded polypropylene pump body.Motor - 1/3 HP, 115 volt with stainless steel shaft, in oil filled chamber with thermal overloadprotection. CSA approved.Impeller - 5 vane reinforced polypropylene, handles 1/2" spherical solids.Seal - Mechanical type in oil filled chamber with ceramic and carbon faces.Switch - Separate float switch, removable for manual operation.Discharge - 1 1/2" NPT. Reducer bushing for 1 1/4" discharge included.



SP33A 30 23 16 5 23

SUBMERSIBLE SUMP PUMP - 1 1/4” DISCHARGEMODEL NO ORDER NO. HP SHIP WT. DESCRIPTION

(LBS.)

SP33A 620135 1/3 10 Submersible sump pump with automatic float switch



ESP33 44 33 13 0 17.5

SUMP/EFFLUENT PUMPS – SUBMERSIBLE TYPE - 1 1/2” - 1 1/4”DISCHARGE

MODEL NO ORDER NO. HP SHIP WT. DESCRIPTION(LBS.)

ESP33AM 620088 1/3 19 Automatic, with separate float switch and 10 ft. cord

ESP33M 620089 1/3 17 Manual, with 10 ft. power cord

ESP33 SERIES SUBMERSIBLE SUMP/EFFLUENT PUMP


Monarch Sump & Sewage Submersible Sewage Pumps

WS SERIES SUBMERSIBLE SEWAGE PUMPS - VORTEXFeatures:Construction - Motor and pump housing is Cast Iron.Cord - 20 foot power cord sealed at motor housing.Impeller - A high capacity vortex impeller, designed for superior solids handling capabili-ties. This impeller is able to pass 2" solids by creating a vortex. Solids do not come intocontact with the impeller. This provides superior clog free operation.Motor - Powerful CSA approved 115 volt, capacitor start motor. The durable cast iron motorhousing dissipates heat away from the motor providing longer life. With thermal overloadprotection and double ball bearings for reliability.Switch - Mercury Free Float switch for automatic on-off operation.Discharge - 2" NPT.Fasteners - 304 Stainless steel fasteners throughout, for serviceability.



WSV52 112 80 40 0 18

SUBMERSIBLE SEWAGE PUMPS - AUTOMATIC AND MANUALMODEL NO PART NO. HP VOLT PH SOLIDS SHIP WT. SWITCH CORD

HANDLING (LBS.) LENGTH

WSV52M 620202 1/2 115V 1 2" 54 Manual 20'

WSV52A 620205 1/2 115V 1 2" 56 Automatic 20'


G e n e r a l P u m p A c c e s s o r i e s

PHOTO PART NO. MODEL DESCRIPTION

W-TYPE AUTOMATIC PRESSURE REGULATORA 78835 W1 0 to 1600 PSI W-Type Automatic pressure regulator with built-in

chemical injector and by-pass tube• Sized for direct mount on to most general pumps• Saves space and plumbing• Maximum pressure can be pre-set

SBH SERIES WET SANDBLASTING ATTACHMENT HEADB 78865 SBH1 Water flow draws sand into spray. Uses dry, sifted, quartz or silica

sand

WATER SUCTION KITC 78866 WW20-152 Make yourself completely mobile with the WW20-152. Draw water

from a pond, creek, lake or even drums of water. Comes completewith garden hose fitting, 25' H.D. 3/4 hose, suction strainer andcheck valve.

REF. PART NO. REPLACES DESCRIPTION1 78836 90.3839.00 O-Ring3 78837 10007870 Nipple4 78838 90.3832.00 O-Ring kit 946 78839 36.3167.66 Valve kit 987 78839 90.5025.00 O-Ring kit 988 78839 90.3575.00 O-Ring kit 989 78839 90.5075.00 O-Ring kit 98

10 78839 90.3589.00 O-Ring kit 9811 78839 36.3165.70 Valve guide kit 98

12 78839 90.3847.00 O-Ring kit 9813 78839 36.3166.70 Bushing kit 9814 78840 94.7436.00 Spring15 78841 36.3169.70 Spring plate16 78842 36.3171.02 Knob17 78843 92.2200.00 Nut18 78844 99.3052.00 Bolt19 78845 36.3172.51 Cap20 78839 90.5065.00 O-Ring kit 9821 78839 90.3822.00 O-Ring kit 98 or 94

22 78839 36.3168.66 Piston kit 9823 78839 97.6132.00 Pin kit 9824 78839 97.4800.00 Ball kit 9825 78839 36.3164.66 Valve seat kit 9827 78847 90.3820.00 O-Ring28 78848 36.2567.70 Bolt29 78849 90.3825.00 O-Ring30 78850 36.3152.22 Body31 78851 90.3827.00 O-Ring32 78852 36.2568.70 Bolt

36 78853 90.3591.00 O-Ring37 78854 36.2560.70 Nipple38 78855 92.8925.00 Filter39 78856 90.3828.00 O-Ring40 78857 36.2569.70 Hose barb41 78858 10.0119.02 Ring nut46 78859 10015766 Nozzle47 78838 90.3582.00 O-Ring kit 9448 78838 94.8217.00 Spring kit 9449 78838 97.4782.00 Ball kit 94

50 78838 90.3572.00 O-Ring kit 9451 78838 90.3585.00 O-Ring kit 9452 78860 36.2563.70 Valve seat53 78861 36.2562.51 Body54 78838 94.7383.00 Spring kit 9455 78838 90.3580.00 O-Ring kit 9456 78862 36.2564.70 Valve57 78863 36.2565.51 Knob58 78838 90.3570.00 O-Ring kit 9459 78864 36.2566.70 Hose barb

PHOTO B PHOTO C

PHOTO A

THE MOST COMMON SPAREPARTS ARE SOLD IN KITPACKAGING


G e n e r a l P u m p & I n t e r p u m p

T9721,T9731, T9791, W972, W973 & W979

PART NO. 70180 70181 70182

Model No. T9721 T9731 T9791

GPM 2.1 2.85 2.5

PSI 1000 1000 1100

RPM 1750 1750 1750

HP 1.5 2.0 2.0

Max. inlet pressure (PSI) 125 125 125

Max. suction lift (ft.hg) 10/8.8 10/8.8 10/8.8

Piston bore (mm) 20 22 20

Piston stroke (mm) 7.8 10.5 9.5

Crankcase capacity (L) 0.3 0.3 0.3

Inlet Port (in.) 1/2 1/2 1/2

Outlet Port (in.) 3/8 3/8 3/8

Shaft diameter (mm) 24 24 24

Weight (lbs.) 11 11 11

REF. PART NO. REPLACES DESCRIPTION

1 78162 49.1200.41 Head

4 70965 90.3841.00 O-Ring kit 1

5 70965 36.2003.66 Valve seal kit 1

6 70965 36.2007.76 Air valve kit 1

7 70965 94.7376.00 Spring kit 1

8 70965 36.2002.51 Valve guide kit 1

9 78164 90.3847.00 O-Ring kit 4

10 78164 98.2220.00 Cap kit 4

11 70965 36.7032.01 Valve unit kit 1

12 78165 90.2703.00 Packing kit 27

13 78165 50.2166.70 Ring kit 27

14 78165 50.1000.51 Head ring kit 27

15 78165 50.0805.70 Packing retainer kit 27

16 78165 90.3612.00 O-Ring kit 27

17 78166 90.1614.00 Ring kit 23

19 78167 50.1500.74 Cover

20 78168 50.2116.51 Spacer

21 78169 90.4097.00 O-Ring

22 78170 91.8329.00 Bearing T9791, W979

22 78170 91.8328.00 Bearing T9721, T9731,W972,W973

23 78172 49.0100.22 Crankcase (W)

23 78173 49.0104.22 Crankcase (T)

24 78174 98.2103.00 Dip stick

25 78175 49.2119.84 Gasket

26 78176 49.1600.22 Crankcase cover (W)

26 78177 49.1603.22 Crankcase cover (T)

28 78178 90.3585.00 O-Ring kit 6

29 78179 97.5968.00 Oil level indicator

30 78180 98.2041.00 Cap

31 78181 49.0204.35 Crankshaft T9791, W979

31 78182 49.0220.35 Crankshaft T9721, W972

31 78183 49.0217.35 Crankshaft T9731, W973


32 78184 97.7330.00 Piston ring

33 78185 91.4878.00 Key

34 78186 50.0300.01 Connecting rod

36 78187 96.6939.00 Washer

37 78188 99.1927.00 Bolt

38 78189 50.0500.56 Piston guide

39 78178 96.7286.00 Washer kit 6

40 78190 50.0404.09 Piston

41 78178 90.5067.00 Anti extrustion ring kit 6

42 78178 96.7280.00 Washer kit 6

43 78178 47.2195.66 Piston bolt kit 6

44 78191 50.2115.51 Spacer

45 78192 90.1634.00 Ring seal

49 78193 98.2100.00 Cap

50 78194 98.2176.00 Cap

51 78195 96.7514.00 Washer

52 78196 96.7380.00 Washer

THE MOST COMMON SPARE PARTS ARE SOLD ONLY IN KIT PACKAGING



T9051, TT9061, TT9071, W905, WW906 & WW907

PART NO. 70183 70184 70185

Model T9051 TT9061 TT9071

GPM 2.11 2.11 2.8

PSI 1015 1015 1500

RPM 1750 3400 3400

HP 1.5 1.5 3

Max. inlet pressure (PSI) 125 125 125

Max. suction lift (ft/hg) 10/8.8 10/8.8 10/8.8


Piston stroke (mm) 9.4 5 6.6

Crankcase capacity (l) 0.33 0.33 0.33

Inlet port (in.) 3/8 3/8 3/8

Oultlet port (in.) 1/4 1/4 1/4

Shaft diameter 5/8 hollow 5/8 hollow 3/4 hollow

MOTOR FLANGE NOT SUPPLIEDWITH PUMP

VERSION AFOR ELECTRIC

MOTORS (60 HZ) 56C

VERSION CGASOLINE ENGINES

TT9061 & TT9071 ONLY


1 78197 51.0106.22 Crankcase

2 78193 98.2100.00 Cap

4 78199 51.2091.02 Side cover

5 78800 90.1565.00 Ring kit 83

6 78180 98.2041.00 Cap

7 78801 51.1200.41 Head

10 70965 90.3841.00 O-ring kit 1

11 70965 36.2003.66 Valve seat kit 1

12 70965 36.2001.76 Air valve kit 1

13 70965 94.7376.00 Spring kit 1

14 70965 36.2002.51 Valve guide kit 1

15 78802 90.3847.00 O-Ring kit 84

16 78802 98.2218.00 Cap kit 84

17 70965 36.7032.01 Valve unit kit 1

18 78803 51.1000.51 Head ring kit 96

19 78803 90.2620.00 Packing kit 96


20 78803 51.0800.70 Rocking ret.kit 96

21 78803 90.3604.00 O-Ring kit 96

22 78803 90.3835.00 O-Ring kit 96


24 78804 91.8014.00 Bushing

25 78174 98.2103.00 Dipstick

26 78805 92.2216.00 Nut

27 78806 96.7008.00 Washer

28 78807 51.0400.09 Piston

29 78808 90.3572.00 O-Ring

30 78809 90.5022.00 Unit extrusion ring

31 78810 96.7070.00 Washer

32 78811 97.7310.00 Piston pin

33 78812 51.1600.22 Crankcase cover

35 78813 51.2101.84 Gasket

36 78814 51.0300.22 Connecting rod

37 78815 51.0500.56 Piston guide


42 78817 10034422 C flange

43 78191 50211551 Spacer

44 78169 90409700 O-Ring

45 78818 90164400 Ring seal

46 78819 90066700 Cir clip

47 78816 91837300 Bearing

48 78820 51020835 Crankshaft TT9061

48 78821 51020935 Crankshaft TT9071

48 78822 51021535 Crankshaft T9051

62 78823 10.0346.22 Motor flange

65 78191 50.2115.51 Spacer

66 78169 90.4097.00 O-Ring

67 78818 90.1644.00 Ring seal

68 78819 90.0667.00 Cir clip

69 78816 91.8373.00 Bearing

70 78824 51.0210.35 Crankshaft

70 78825 51.0211.35 Crankshaft




T9951, T9961, T9971, T701, T711 & T911

PART NO. 70186 70187 70188

Model T9951 T9961 T9971

GPM 3.5 4.0 4.0

PSI 1300 1100 2000

RPM 1750 1750 1750

HP 3.0 3.0 5.5

Max. inlet pressure (psi) 125 125 125

Max. suction lift (ft/hg) 10/8.8 10/8.8 10/8.8


Piston stroke (mm) 8.5 10 10

Crankcase capacity (l) 0.45 0.45 0.45

Inlet port (in.) 1/2 1/2 1/2

Outlet port (in.) 3/8 3/8 3/8

Shaft diameter (mm) 24 24 24

Weight (lbs.) 18.7 18.7 18.7

MOTOR FLANGENOT SUPPLIEDWITH PUMP


1 78826 50.1207.41 Head

4 70965 90.3841.00 O-Ring kit 1

5 70965 36.2003.66 Valve seal kit 1

6 70965 36.2001.76 Air valve kit 1

7 70965 94.7376.00 Spring kit 1

8 70965 36.2002.51 Valve guide kit 1

9 78164 90.3847.00 O-Ring kit 4

10 78164 98.2220.00 Cap kit 4

11 70965 36.7032.01 Valve unit kit 1

12 78165 90.2703.00 Packing kit 27

13 78165 50.2166.70 Ring kit 27

14 78165 50.1000.51 Head ring kit 27

15 78165 50.0805.70 Packing retainer kit 27

16 78165 90.3612.00 O-Ring kit 27

17 78166 90.1614.00 Ring kit 23


20 78168 50.2116.51 Spacer

21 78169 90.4097.00 O-Ring

22 78170 91.8329.00 Bearing

23 78827 50.0104.22 Crankcase

24 78174 98.2103.00 Dipstick

25 78828 50.2119.84 Gasket


28 78178 97.5968.00 O-Ring kit 6


30 78180 98.2041.00 Cap

31 78830 50.0218.35 Crankshaft T711-T911-T9961-T9971

31 78831 50.0219.35 Crankshaft T701-T9951

32 78184 97.7330.00 Piston ring

33 78832 91.4890.00 Key

34 78186 50.0300.01 Connecting rod - T701-T711-T9961-T9951


36 78187 96.6939.00 Washer

37 78188 99.1927.00 Bolt

38 78834 50.0501.56 Piston guide

39 78178 96.7286.00 Washer kit 6

40 78190 50.0404.09 Piston

41 78178 90.5067.00 Unit extrustion ring kit 6

42 78178 96.7280.00 Washer kit 6

43 78178 47.2195.66 Piston bolt kit 6

44 78191 50.2115.51 Spacer

45 78192 90.1634.00 Ring seal

49 78193 98.2100.00 Cap

50 78194 98.2176.00 Cap

51 78195 96.7514.00 Washer

52 78196 96.7380.00 Washer



Westward Pressure Washer Pumps and Parts

AXD3020GAxial radial pump, direct mount.Built-in unloader & soaper. Fitsmost gas engines with 3/4" roundshaft: Briggs & Stratton, Honda,Kawasaki, Kohler, Kubota, &Yamaha

AXD2020EAxial radial pump, direct mount.Built-in unloader & soaper. Fitsmost electric motors with 5/8"round shaft: Baldor

TO FIT WSSE1015AND WSSE1520PUMP ASSEMBLYPUMP ONLYSpecifications:• 2.0 GPM• 1.5 HP• 3400 RPM• 2000 PSI• 5/8” Hollow Shaft

LWDK3020GTriplex ceramic plunger pump,direct mount, built-in unloaderand soaper. Fits most gas en-gines with 3/4" round shaft:Briggs & Stratton, Honda,Kawasaki, Kohler, Kubota, &Yamaha

TO FIT WSS2055PUMP ASSEMBLYPUMP ONLYSpecifications:• 3.0 GPM• 5.5 HP• 3400 RPM• 2000 PSI• 3/4" Hollow Shaft

PART NO.

SPP 70189

SPP 70190


SPP 70960 Seal Kit

SPP 70961 Valve Kit

PART NO.

SPP 70191

SPP 70192


SPP 70960 Seal Kit

SPP 70961 Valve Kit

PART NO.

SPP 70193

SPP 70194


SPP 70962 Seal Kit

SPP 70965 Valve Kit

PUMP OIL• Non-detergent, non foaming• Specially formulated and rated for superiorrust protection and oxidation protection• Ideal for axial radial pumps•Universal Transmission Fluid Heavy (UTFH)


74225 1 litre (UTFH)

TO FIT WSS2005EPUMP ASSEMBLYPUMP ONLYSpecifications:• 2.7 GPM• 5 HP• 3400 RPM• 2000 PSI• 3/4" Hollow Shaft

SEE SECTION 7 FOR MOREINFORMATION


Westward Pressure Washer Pumps and Parts

COMPONENTS FOR ALL WESTWARD PRESSURE WASHERS

FEMALE SOCKET FEMALE PLUG MALE PLUG

1/4" NPT SPP 74228 SPP 74226 SPP 78118 SPP 78121 SPP 781243/8" NPT SPP 74229 SPP 74227 SPP 78119 SPP 78122 SPP 781251/2" NPT SPP 74232 SPP 74591 SPP 78120 SPP 78123 SPP 78126


73645 Filter screen washer (2005E, E1015, E1520, 2055)

70967 Water inlet filter (3011)

70968 Soap hose assy

78088 Soap suction filter

70969 Garden hose adapter assy

70970 1/2" thermal valve (2055)

70971 E-Z start unloader valve (3011)

70972 Repair kit for 70971

70973 Seal kit for 70971

70974 By pass hose (3011)

75027 5000 PSI gauge (3011)

78083 Handgun (3011)

78127 Repair kit for 78083 Handgun

78105 Handgun (all units except 3011)

78129 Repair Kit for 78105 Handgun

78078 18" lance w/molded grip


78080 36" lance w/molded grip (all units)


70975 Red tip (2005E, E1015, E1520, 2055) 0°

70976 Yellow tip (2005E, E1015, E1520, 2055) 15°

70977 White tip (2005E, E1015, E1520, 2055) 40°

70978 Black Soaper nozzle (all units)

70979 Red tip (3011) 0°

70980 Yellow tip (3011) 15°

70981 White Tip (3011) 40°

70982 30' high pressure hose with couplers (2055E,E1015, E1520, 2055)

70983 50' high pressure hose with couplers (3011)

ZWD4030GTriplex ceramic plunger pump,direct mount. Fits most gasengines with 1" round shaft:Briggs & Stratton, Honda,Kawasaki, Kohler, Kubota,& Yamaha

PART NO.

SPP 70195

SPP 70196


SPP 70964 Seal Kit

SPP 70965 Valve Kit

TO FIT WSS3011PUMP ASSEMBLYPUMP ONLYSpecifications:• 4.0 GPM• 11 HP• 3400 RPM• 3000 PSI• 1" Hollow Shaft

FEMALE COUPLER XMPT

O-RINGS FORFEMALE COUPLERS

FOR MORE INFORMATIONSEE SECTION 7


C e n t r i g u g a l W a t e r P u m p s

2" AND 3" HONDA POWERED WATER PUMPSGeneral purpose centrifugal water pumps constructed from aluminum for performancereliability, durability, and lightweight portability. These pumps are economical and ideal fordrainage and most general purpose water pumping applications including effulent.

PART NO. WSS20402” GENERAL PURPOSE PUMPEngine: 4 HP Honda “Oil Alert”Pump: Centrifugal AluminumImpeller: Cast IronInlet/Outlet: 50 mm (2")Max Flow: 580 L/min, 150 Gal/minMax Head: 85 feetSolids: NoDry Weight: 21 kg (46 lbs.)

PART NO. WSS30503” GENERAL PURPOSE PUMPEngine: 5.5 HP Honda “Oil Alert”Pump: Centrifugal AluminumImpeller: Cast IronInlet/Outlet: 80 mm (3")Max Flow: 980 L/min, 255 Gal/minMax Head: 95 feetSolids: NoDry Weight: 27 kg (59 lbs.)

PARTS BREAKDOWN SEE SECTION 9

PARTS BREAKDOWN SEE SECTION 9

PART NO. WSST30803”TRASH PUMPEngine: 8 HP Honda GX Oil AlertImpeller: Cast IronInlet/Outlet: 80 mm (3")Max Flow: 1100 L/min, 300 Gal/minMax Head: 100 feetMax Lift: 25 feetSolids: 1"Dry Weight: 59 kg (130 lbs.)

PART NO. WSS20502” GENERAL PURPOSE PUMPEngine: 5 HP Honda GCPump: Centrifugal AluminumImpeller: Cast IronInlet/Outlet: 50 mm (2")Max Flow: 580 L/min, 150 Gal/minMax Head: 85 feetSolids: NoDry Weight: 21 kg (46 lbs.)


W a t e r P u m p A c c e s s o r i e s

ALL BRONZE CHECK VALVES

PART NO REPLACES PIPE SIZE SHIP WT. (LBS)

78708 627710 ½" 1 ¼

78709 627720 ¾" 1 ¼

78710 627730 1" 2

78711 627740 1 ¼" 2 ½

78712 627750 1 ½" 3

78713 627760 2" 3 ½

76147 CU-300 3" 3 ½

76148 CU-400 4" 4 ½

PLASTIC SUCTION STRAINER


78704 627815 1 ½" 1/3

78705 627825 2" 1/3

74994 70002800 3" ¾"


78706 627530 2 ½" 5

78707 627540 3" 5

HD BRONZE FOOT VALVE WITH PERFORATED STAINLESS STEEL STRAINER

CYCOLAC FOOT VALVE WITH STRAINER (ABS PLASTIC)

PART NO REPLACES PIPE SIZE MIN. WELL DIA.

78701 626860 1" 2"

78702 626870 1 ¼" 2 ½"

78703 626871 1 ½" 2 ½"

STANDARD BRONZE FOOT VALVE WITH PERFORATED BRASS STRAINER

PART NO REPLACES PIPE SIZE MIN. WELL DIA.

78696 627610 3/4" 1 ¼"

78697 627620 1" 2"

78698 627630 1 1/4" 2 1/2"

78699 627640 1 ½" 3"

78700 6927650 2" 3 ½"

76145 FU-300 3" 3 ½"

76146 FU-400 4" 4 ½"

CAST IRON SUCTION STRAINERS-STR SERIES

PART NO MODEL NO. REPLACES PIPE SIZE DESCRIPTION

78714 STR-1 1/4 409390 1 ¼" Rugged construction, painted,

78715 STR-1 1/2 409340 1 ½" with standard pipe thread. An ideal

78716 STR-2 409350 2" choice for the protection of your pump,

78717 STR-3 409360 3" Designed with a maximum “open”

78718 STR-4 409370 4" area for continuous flow.

NYLON FOOT STRAINERSThe Slimline plastic foot strainer is used forsuction on: 1 ¼", 1 ½", or 2" hose. Thisstrainer includes a check valve type shut offto prevent pump prime loss by holding wa-ter in hose when pump is shut off.


77020 08ART17B 1 ¼" foot strainer

77021 08ART17C 1 ½" foot strainer

77022 08ART17D 2" foot strainer


D e l a v a n P u m p C o u p l e r s

PART NO. PUMP COUPLERS REPLACES PUMP AND TRACTOR PTO WEIGHT DESCRIPTIONCOUPLER MATCH

70400 46814-1 For 6 - roller pump with 5/8" pump 2.1 lbs. Fits either 540 or 1000 rpm 1 3/8" shaftsshaft, 1 3/8” 540 & 1000 rpm PTO Allows quick and simple slip-on, slip off

installation of a pump to a tractor PTO70401 46814-2 For old-style and competitive pumps 2.1 lbs. shaft. Just pull collar back and slide on

with 7/8" shaft, 1 3/8" 540 & 1000 or slide off. Coupler is clamped to pumpPTO shaft with allen head socket screws.

Dual Speed 540 & Corrosion resistant cast aluminum; collar70402 1000 RPM PTO Quick 46814-3 For 7-* & 8-roller pumps with 15/16" 2.1 lbs. is Super Tough Nylon

Couplers shafts, 1 3/8" 540 & 1000 PTO

70412 46819 Replacement ¼" socket headsetscrew for 70400, 70401, 70402

70405 35735 For 5-, 7-* & 8-Roller pumps with 2.3 lbs. Same quick installation as above; use on15/16" shafts, 1 3/8" 540 RPM PTO 1 3/8” 540 RPM PTO only; body is steel

70406 35979 For Turbo 90 pump & 5- & 8-Roller 2.3 lbs. Same as above except use on 1 3/8"pumps with 15/16" shafts, 1 3/8" 1000 RPM PTO

Steel Bodied PTO Quick 1000 RPM PTO70407 Couplers for Turbo 90 35992 For Turbo 90 pump with 15/16" shaft, 4.6 lbs. Same as above except use on 1 3/4"

and Roller Pumps 1 3/4" 1000 RPM PTO 1000 RPM PTO

76517 35992 Replacement pin for above couplersExcept for 70407 *7-Roller pump on 540 PTO only

NOTE: Do not use P/N 46814 Coupler76518 35993 Replacement pin for 70407 coupler for 5 Roller or Turbo 90 Pumps

70408 46935-1 For Turbo 90 pump and 5- & 8-Roller 2.3 lbs. This coupler reduces possible vibrationPumps with 15/16" shafts, 1 3/8" by clamping a full 360° on the pump1000 RPM PTO shaft and PTO. Better centering of pump

shaft to tractor PTO; less chance for70409 47647 For Turbo 90 pump & 5- & 8-Roller 3.7 lbs. uneven wear. Both ends of coupler must

pumps with 15/16" shafts, 1 3/4" be wrench-tightened onto PTO & pump1000 RPM PTO shafts before operation. Do not force

CollarTM Coupler for coupler too far onto PTO. After coupler isTurboTM 90 Pumps in position, 1/4"-3/8" of PTO splineand Roller Pumps shouldbe visible.

70466 50101 For 4-Roller pump with 5/8" shaft & 2.2 lbs Aluminum set-screw coupler. Set screws5/8" motor or engine drive shaft are recessed for safety.

Set Screw Couplerfor 4-Roller Pump


H y p r o P u m p C o u p l e r s

HYPRO QUICK COUPLER (FEMALE TO FEMALE)PUMP END

PART NO. REPLACES PTO (I.D.) (I.D.) MATERIAL RPM PUMP MODEL

70420 1321-0006 1 3/8" (6 spline) 5/8" die cast 540 6500

70421 1321-0007 1 3/8" (6 spline) 15/16" die cast 540 1500, 1700, 7560, 7700

70422 1321-0008 1 3/8" (21 spline) 5/8" die cast 1000 4000, 6500

70423 1321-0009 1 3/8" (21 spline) 15/16" die cast 1000 1500, 1700, 7560

70448 1321-0012 1 3/8" (multi-speed) 5/8" die cast 540/1000 4000, 6500

70449 1321-0013 1 3/8" (multi-speed) 15/16" die cast 540/1000 1500, 7560, 7700

70458 1323-0072 1 3/8" (6 spline) 15/16" forged steel 540 1500, 1700, 7560, 7700

70459 1323-0073 1 3/8" (21 spline) 15/16" forged steel 1000 1500, 1700, 7560

70462 1323-0074 1 3/8" (6 spline) 5/8" forged steel 540 6500

70463 1323-0075 1 3/8" (21 spline) 5/8" forged steel 1000 4000, 6500

70464 1323-0076 1 3/8" (multi-speed) 15/16" forged steel 540/1000 1500, 1700, 7560

70465 1323-0077 1 3/8" (multi-speed) 5/8" forged steel 540/1000 4000,6500

76515 3250-004 Replacement Nylon ball for above couplers

PUMP ENDPART NO. REPLACES PTO (I.D.) (I.D.) MATERIAL RPM PUMP MODEL

79035 1320-0015 3/4" 5/8" steel * 4000, 6500

71028 1320-0016 5/8" 5/8" steel * 4000, 6500

70424 1320-0022 1 3/8" (6 spline) 5/8" die cast 540 6500 Series

70425 1320-0033 1 3/8" (6 spline) 15/16" die cast 540 1500, 1700, 7560, 7700

70427 1320-0038 1 3/8" (21 spline) 15/16" die cast 1000 1500, 1700, 7560

70426 1320-0053 1 3/8" (21 spline 5/8" die cast 1000 4000, 6500

70413 1320-0054 3/4" 15/16" die cast * 1500, 1700, 7560, 7700

71419 1320-0059 1 3/8" (6 spline) 1" die cast 540 1200/5200

70415 1320-0076 1 3/8" (6 spline) 15/16" forged steel 540 1500, 1700, 7560, 7700

70416 1320-0077 1 3/8" (6 spline) 5/8" forged steel 540 6500


70445 1320-0079 1 3/8" (21 spline) 5/8" forged steel 1000 4000, 6500


70447 1320-0081 1 3/8" (6 spline) 1" forged steel 540 1200/5200

* Refer to recommended pump rpm

STEEL

DIE CAST FORGED STEEL

FORGED STEELDIE CAST

HYPRO ADAPTER FOR ADAPTING PUMPS TO PTO'S ANDGAS ENGINES (FEMALE TO FEMALE)


Ace Couplers

ACE STANDARD COUPLERSPART NO. REPLACES DESCRIPTION

70432 612-6SP Fits 5/8" shaft on to 540 rpm 6 spline



70434 812-21SP-78 Fits 7/8" shaft on to 1000 rpm 21 spline




SHAFT COUPLINGS

SERIES 2739 (4 1/2 HP LIMIT)PART NO. REPLACES COUPLING BORE SIZE

70451 2739-0001 5/8" w/ 3/16" key

70452 2739-0002 3/4" w/ 3/16" key

70453 2739-0003 7/8" w/ 3/16" key

70454 2739-0004 15/16" w/ 1/4" key

70455 2739-0005 1" w/ 1/4" key

70456 2739-0006 1 1/8" w/ 1/4" key

70450 2729-0001 Centre disc for 2739 couplings

70457 2729-0005 HD centre disc for 2739 coupler

SERIES 2738 (2 HP LIMIT)PART NO. REPLACES COUPLING BORE SIZE

70441 2738-0001 1/2" w/ 1/8" key

70442 2738-0002 5/8" w/ 3/16" key

70443 2738-0003 3/4" w/ 3/16" key

70444 2738-0004 7/8" w/ 3/16" key

70440 2728-0001 Centre disc for 2738 couplings


70419 1" - 15 spline male x 5/8" female

GARDEN TRACTOR AND ATV STEEL COUPLER

ACE QUICK COUPLERSPART NO. REPLACES DESCRIPTION

70436 612-6SPQC Fits 5/8" shaft 540 rpm 6 spline

70437 612-21SPQC Fits 5/8" shaft 1000 rpm 21 spline

70438 812-6SPQC-78 Fits 7/8" shaft 540 rpm 6 spline




76519 BAC-83-QC Replacement ball for above couplers

COUPLINGEND

CENTERDISC

COUPLINGEND

STEELBODY

STEEL BODY

STEEL BODY


Pump Couplers - 540 RPM - 6 Spline

FFEMALE # PART OVERALL WEIGHTSPLINE OF NO. A B LENGTH KG

SPLINESIN MM IN MM IN MM IN MM

1 3/8 35 6 4981 5/8 16 1 3/8 35 4 5/8 117.5 0.82

1 3/8 35 6 4982 3/4 19 1 3/8 35 4 5/8 117.5 0.78

1 3/8 35 6 4983 7/8 22 1 3/8 35 4 5/8 117.5 0.74

1 3/8 35 6 4984 1 25 1 1/2 38 4 5/8 117.5 0.66

GENERAL PURPOSE PUMP ADAPTOR

QUICK RELEASE ADAPTER

SPECIAL PTO ADAPTER


PTO 4895 1" Round with 540 rpm (6 spline)

PTO 4896 1 1/8" Round with 540 rpm (6 spline)





PTO 4900 7/8" Round (A) with 540 rpm (6 spline)

PTO 4901 1" Round (A) with 540 rpm (6 spline)


PTO 4981 5/8" Round with 540 rpm (6 spline)



PTO 4984 1" Round with 540 rpm (6 spline)

B = 0.3165"/0.3188" (8.04mm/8.098mm). holes fitted with grub screwsF = 1 3/8" (35mm) x 6 Spline.

C = 3/8" UNC holes fitted with grub screws.

Documents

SPRAYER PARTS CATALOGUE PUMPS AND COUPLERSwestwardparts.com/public/downloads/catalogue/sprayer-parts/1... · 1-4 PUMPS AND COUPLERS SPRAYER PARTS CATALOGUE©2003 Delavan 4 Roller