Spirou Patsi 67, 11855 Athens, Greece HUBER S.A.Spirou Patsi 67, 11855 Athens, Greece +30 (210) 3458126, 3475784 Fax: +30 (210) 3478074 Email: [email protected] HUBER S.A. Products

Spirou Patsi 67, 11855 Athens, Greece

+30 (210) 3458126, 3475784

Fax: +30 (210) 3478074

Email: [email protected]

HUBER S.A.Products Contact

2

EN853 1SN DN12 DIN 20022 SAE100R1AT ID 1/2" WP 160BAR

Read the hydraulic hose markings

Modern hoses are c lear ly marked with thehose type, s ize, pressure rating.

Do not re ly on this information if you think thesystem pressure may be greater but a lsonever f it a new hose that is rated with a lowersize or pressure.

Each hose on a system will probably have adifferent rating so make sure you check eachone. Some will be high f low and high pressurewhile other parts of the c ircuit may requirelower f low and lower work ing pressures.

Ident ify the hose size

Measure and specify the ID not the OD.

For example 13.0mm is the hose bore s ize of ahose with nominal diameter of 12, not the outsidediameter.

Because of different wall thicknesses you cannotre ly on measur ing the wall thickness of the tube.

Typical markings and measurements of a Hydraulic Rubber hose with 1 Steel Braid.

EN853, DIN20022 and SAE100R2AT are European, German and American markings. Either ofthem specifies that the hose has 1 steel braid and is suitable for swaging on it, high pressurehydraulic fittings. 1SN is equivalent of 1 STEEL BRAID. DN12 specifies the NOMINAL DIAMETER. ID 1/2” is the INTERNAL DIAMETER of the hose. WP 160 BAR is the WORKING PRESSURE in BAR.

Typical markings and measurements of a Hydraulic Rubber hose with 2 Steel Braids.

Typical markings and measurements of a Hydraulic Rubber hose with 4 Steel Spirals type SP

EN853 2SN DN12 DIN 20022 SAE100R2AT ID 1/2" WP 275 BAR

Typical markings and measurements of a Hydraulic Rubber hose with 4 Steel Spirals type SH

Typical markings and measurements of a Hydraulic Rubber hose with 6 Steel Spirals type R 15

EN856 4SP DN19 DIN 20023 SAE100R9R ID 3/4" WP 350 BAR

EN856 4SH DN38 DIN 20023 ID 1.1/2" WP 290 BAR

EN856 6SP DN38 DIN 20023 SAE100R15 ID1.1/2" WP 420 BAR

135° Female 24° conewith O-Ring Metric

90°Female 24° conewith O-Ring Metric

Male 24° cone Metric

Standpipe Straight Metric

135° Standpipe Metric

90° Standpipe Metric

Female 24° conewith O-Ring Metric

1 2 3 4

5 6 7 8

90°Female 60° coneBSP

Male 60° coneBSP

135° Female 60° coneBSP

Female 60° coneBSP

Male 60° coneBSPT

Male 60° coneNPT

Female 74° coneUNF

135° Female 74° coneUNF

90° Female 74° coneUNF

Male 74° coneUNF

SAE Flange Straight3000 PSI

SAE Flange 45°6000 PSI


Flange Halves3000 PSI

SAE Flange Straight6000 PSI



Flange Halves6000 PSI

Banjo Metric

1

6

3 4

5

1 2 3 4

1 2

5 6 8

3 4

7

Cutting Ring

Cutting Ring

ΔιαστάσειςØ χιλ.

Εσωτερική

Ø χιλ.

Πάνω στο Πλέγμα

Ø χιλ.

Εξωτερική

Πίεση Λειτουγίας

Bar

Πίεση Θραύσης

Bar

Ακτίνα Κάμψης

χιλ.

Βάρος

Κιλά/μέτρο

3/16” 48 111 134 415 1650 90 31

1/4” 64 127 15 400 1600 100 38

5/16” 79 143 166 350 1400 115 45

3/8” 95 167 19 330 1320 130 55

1/2” 127 198 222 275 1100 180 66

5/8” 159 23 254 250 1000 200 79

3/4” 19 27 293 215 850 240 95

1” 254 349 381 165 650 300 137

1.1/4” 318 445 483 125 500 420 202

1.1/2” 381 508 546 90 360 500 275

2” 508 635 673 80 320 630 348

Tube : Seamless oil resistant.Reinforcement : Two braids of HTS wire.Cover : Oil, weather & abrasion resistantTemperature : -40ºC to 120ºC.Application : For high pressure hydraulic oils fuel, lubricating oils, water and air.End Connection : Swaged or Crimped or Reusable type .

NominalØ

Ø mm.

Internal Ø

Ømm.

On the braid

Ø mm.

External

Working Pressure

Bar

Burst Pressure

Bar

Bending Radius

mm.

Weight

Kg/m

1/4” 64 147 179 450 1800 150 63

3/8” 95 175 214 445 1780 180 78

1/2” 127 202 246 415 1660 230 93

5/8” 159 238 282 350 1400 250 113

3/4” 19 282 322 350 1400 300 152

1” 254 353 397 280 1120 340 206

1.1/4” 318 46 508 210 840 460 329

Tube : Seamless oil resistant.Reinforcement : Four layers of HTS wires.Cover : Oil, weather & abrasion resistantTemperature : -40ºC to 120ºC.Application : For high pressure hydraulic oils fuel, lubricating oils, water and air.End Connection : Swaged or Crimped or Reusable type .

NominalØ

Ø mm.

Internal Ø

Ømm.

On the braid

Ø mm.

External

Working Pressure

Bar

Burst Pressure

Bar

Bending Radius

mm.

Weight

Kg/m

3/4” 19 284 322 420 1680 280 153

1” 254 352 387 380 1520 340 2,12

1.1/4” 318 419 455 350 1400 460 258

1.1/2” 381 488 535 290 1160 560 346

2” 508 632 681 250 1000 700 492

Tube : Seamless oil resistant.Reinforcement : Four layers of HTS wires.Cover : Oil, weather & abrasion resistantTemperature : -40ºC to 120ºC.Application : For high pressure hydraulic oils fuel, lubricating oils, water and air.End Connection : Swaged or Crimped or Reusable type .

Tube : Synthetic rubber, resistant against hydraulic fluids.Reinforcement : Four spiral layers DN 19 – DN 25 and six spiral layers DN 32 – DN 38 ofhigh tensile steel wireCover : Oil, weather & abrasion resistantTemperature : -40ºC to 120ºC.Application : For high pressure hydraulic oils fuel, lubricating oils, water and

NominalØ

Ø mm.

Internal Ø

Ø mm.

External

Working Pressure

Bar

Burst Pressure

Bar

Bending Radius

mm.

3/4” 19.5 32 420 840 265

1” 26 39 420 840 330

1.1/4” 32 51 420 840 445

1.1/2” 39 60 420 840 530

NominalØ

Ø mm.

Internal Ø

Ømm.

On the braid

Ø mm.

External

Working Pressure

Bar

Burst Pressure

Bar

Bending Radius

mm.

Weight

Kg/m

3/16” 48 95 118 250 1000 90 19

1/4” 64 111 134 225 900 100 23

5/16” 79 127 15 215 850 115 27

3/8” 95 151 174 180 720 130 34

1/2” 127 183 206 160 640 180 42

5/8” 159 214 237 130 520 200 51

3/4” 19 254 277 105 420 240 64

1” 254 333 356 88 350 300 94

1.1/4” 318 405 435 63 250 420 129

1.1/2” 381 468 506 50 200 500 159

2” 508 64 64 40 160 630 212

Tube : Seamless oil resistant.Reinforcement : One braid of HTS wire.Cover : Oil, weather & abrasion resistantTemperature : -40ºC to 120ºC.Application : For high pressure hydraulic oils fuel, lubricating oils, water and air.End Connection : Swaged or Crimped or Reusable type .

C utting Ring

C utting Ring

How to identify hydraulic hose for replacement

This information covers high pressure hydraulic hose for systems such as industrial machines, marine applications, tractors,excavators, presses and pressure hoses etc.Keep a record of the following information to ensure easy maintenance and replacement of your hoses.

mailto:[email protected]?subject=??? p??s??? ???. ??sta ??�pe?

mailto:[email protected]?subject=Att. Mr. Costas Huber


+30 (210) 3458126, 3475784

Fax: +30 (210) 3478074



Example of an enquiry

Our Client asks for : 20 pieces of hose type SAE100R2AT, hose Inside Ø 3/4”, with 2 Fittings Part Number M118 and M118.Overall length 2,60 meters each.

Our Offer20 pieces hose type SAE100R2AT (our hose with 2 steel braids), Inside Ø 3/4” with 2 fittings the first Female M26x1.5-18 with O-Ring Metricand the second Female M26x1.5-18 with O-Ring MetricOverall L= 2,60 metres each.

Price € …… /piece.




You measure theInner diameter in mm


You measure theOuter diameter in mm

Measuring Metric Threads of L Series

Male 24° Cone Female 24° Cone with O-Ring

1,5 mm or 2 mm

The pitch of the thread

METRIC THREAD MEASUREMENTS

ThreadFemaleInside Ø

mm

MaleOutside Ø

mm

12x1.5 10.5 12

14x1.5 12.5 14

16x1.5 14.5 16

18x1.5 16.5 18

22x1.5 20.5 22

26x1.5 26

27x2 25 27

30x2 28 30

36x2 34 36

45x2 43 45

52x2 50 24.5

1 2 3 4

NominalØ

Hose IDØ Thread

InsideØ of

cuttingring

Metric FemaleO-Ring

Metric Female135° O-Ring


Metric MaleO-Ring

Standpipe

Measure theoutside Ø

in mm

Standpipe135°


in mm

Standpipe90°


in mm

Metric Banjo

Measure theinside Øin mm

5 3/16” M12x1,5 6 M101 M201 M301 M401 M501 M601 M701 M801

5 3/16” M14x1,5 8 M102 M202 M302 M402 M502 M602 M702 M802

6 1/4” M12x1,5 6 M103 M203 M303 M403 M503 M603 M703 M803

6 1/4” M14x1,5 8 M104 M204 M304 M404 M504 M604 M704 M804

6 1/4” M16x1,5 10 M105 M205 M305 M405 M505 M605 M705 M805

6 1/4” M18x1,5 12 M106 M206 M306 M406 M506 M606 M706 M806

8 5/16” M14x1,5 8 M107 M207 M307 M407 M507 M607 M707 M807

8 5/16” M16x1,5 10 M108 M208 M308 M408 M508 M608 M708 M808

8 5/16” M18x1,5 12 M109 M209 M309 M409 M509 M609 M709 M809

10 3/8” M16x1,5 10 M110 M210 M310 M410 M510 M610 M710 M810

10 3/8” M18x1,5 12 M111 M211 M311 M411 M511 M611 M711 M811

10 3/8” M22x1,5 15 M112 M212 M312 M412 M512 M612 M712 M812

12 1/2” M22x1,5 15 M113 M213 M313 M413 M513 M613 M713 M813

12 1/2” M26x1,5 18 M114 M214 M314 M414 M514 M614 M714 M814

16 5/8” M26x1,5 18 M115 M215 M315 M415 M515 M615 M715 M815

16 5/8” M27x2 18 M116 M216 M316 M416 M516 M616 M716 M816

16 5/8” M30x2 22 M117 M217 M317 M417 M517 M617 M717 M817

20 3/4” M26x1.5 18 M118 M218 M318 M418 M518 M618 M718 M818

20 3/4” M30x2 22 M119 M219 M319 M419 M519 M619 M719 M819

25 1” M36x2 28 M120 M220 M320 M420 M520 M620 M720 M820

32 1.1/4” M45x2 35 M121 M221 M321 M421 M521 M621 M721 M821

40 1.1/2” M52x2 42 M122 M222 M322 M422 M522 M622 M722 M822

HUBER S.A.

41 2 3

*The most common threads for thesetype of fittings are marked in blue.

Metric Fittings Series L Part Numbers




+30 (210) 3458126, 3475784

Fax: +30 (210) 3478074



Example of an enquiry

Our Client asks for : 20 pieces of hose type SAE100R1AT, hose Inside Ø 3/8”, with 2 Fittings Part Number S109 and S109.Overall length 1,80 meters each.

Our OfferWe offer : 20 pieces hose type SAE100R1AT (our hose with 1 steel braid), Inside Ø 3/8” with 2 fittings the first Female - M18X1,5 -10 withO-Ring Metric and the second Female - M18X1,5 - 10 with O-Ring Metric.Overall L= 1,80 metres each.


HUBER S.A.Nominal

ØHose ID

Ø Thread

InsideØ of

cuttingring

Metric FemaleO-Ring



Metric MaleO-Ring

Standpipe


in mm

Standpipe135°


in mm

Standpipe90°


in mm

Metric Banjo

Measure theinside Øin mm

5 3/16” M14x1,5 6 S101 S201 S301 S401 S501 S601 S701 S801

5 3/16” M16x1,5 8 S102 S202 S302 S402 S502 S602 S702 S802

6 1/4” M14x1,5 6 S103 S203 S303 S403 S503 S603 S703 S803

6 1/4” M16x1,5 8 S104 S204 S304 S404 S504 S604 S704 S804

6 1/4” M18x1,5 10 S105 S205 S305 S405 S505 S605 S705 S805

6 1/4” M20x1,5 12 S106 S206 S306 S406 S506 S606 S706 S806

8 5/16” M18x1,5 10 S107 S207 S307 S407 S507 S607 S707 S807

8 5/16” M20x1,5 12 S108 S208 S308 S408 S508 S608 S708 S808

10 3/8” M18x1,5 10 S109 S209 S309 S409 S509 S609 S709 S809

10 3/8” M20x1,5 12 S110 S210 S310 S410 S510 S610 S710 S810

10 3/8” M22x1,5 14 S111 S211 S311 S411 S511 S611 S711 S811

12 1/2” M22x1,5 14 S112 S212 S312 S412 S512 S612 S712 S812

12 1/2” M24x1,5 16 S113 S213 S313 S413 S513 S613 S713 S813

16 5/8” M24x1,5 16 S114 S214 S314 S414 S514 S614 S714 S814

16 5/8” M30x2 20 S115 S215 S315 S415 S515 S615 S715 S815

20 3/4” M30x2 20 S116 S216 S316 S416 S516 S616 S716 S816

20 3/4” M36x2 25 S117 S217 S317 S417 S517 S617 S717 S817

25 1” M36x2 25 S118 S218 S318 S418 S518 S618 S718 S818

25 1” M42x2 30 S119 S219 S319 S419 S519 S619 S719 S819

32 1.1/4” M42x2 30 S120 S220 S320 S420 S520 S620 S720 S820

32 1.1/4” M52x2 38 S121 S221 S321 S421 S521 S621 S721 S821

40 1.1/2” M52x2 38 S122 S222 S322 S422 S522 S622 S722 S822

Male 24° Cone Female 24° Cone with O-Ring

1,5 mm or 2 mm

The pitch of the thread

METRIC THREAD MEASUREMENTS

ThreadFemaleInside Ø

mm

MaleOutside Ø

mm

14x1.5 12.5 14

16x1.5 14.5 16

18x1.5 16.5 18

20x1.5 18.5 20

22x1.5 20.5 22

24x1.5 22.5 24

30x2 28 30

36x2 34 36

42x2 40 42

52x2 50 52

Measuring Metric Threads of S Series

41 2 3






You measure theOuter diameter in mm

1 2 3 4

HUBER S.A.


Metric Fittings Series S Part Numbers




+30 (210) 3458126, 3475784

Fax: +30 (210) 3478074



Example of enquiry

Our Client asks for : 10 pieces of hose type SAE100R2AT, hose, Inside Ø 3/4”, with 2 Fittings Part N° BSP122 and BSP322.Overall length 2 meters each.

Our Offer

We offer : 10 pieces hose type SAE100R2AT (our hose with 2 steel braids), Inside Ø 3/4” with 2 fittings the first Female BSP3/4” and the second Female BSP 90° for hose 3/4”.Overall L= 2 metres each.


Measuring BSP Threads

British Standard Pipe Thread – Parallel (BSPP)

FemaleOuter Inner Threads

Nominal Dash Diameter Diameter Pitch perSize Size (mm) (mm) (mm) inch

1/8" 2 9.728 8.566 0.907 281/4" 4 13.157 11.445 1.337 193/8" 6 16.662 14.95 1.337 191/2" 8 20.955 18.631 1.814 145/8" 10 22.911 20.587 1.814 143/4" 12 26.441 24.117 1.814 147/8" 14 30.201 27.877 1.814 141" 16 33.249 30.291 2.309 11

1 1/8" 18 37.897 34.939 2.309 111 1/4" 20 41.91 38.952 2.309 11

22 44.323 41.365 2.309 111 1/2" 24 47.803 44.845 2.309 111 3/4" 28 53.746 50.788 2.309 11

2" 32 59.614 56.656 2.309 112 1/4" 36 65.71 62.752 2.309 112 1/2" 40 75.184 72.226 2.309 112 3/4" 44 81.534 78.576 2.309 11

3" 48 87.884 84.926 2.309 11

Male

1 3/8"

British Standard Pipe Thread - Tapered (BSPT)

Male FemaleOuter Inner Threads

Nominal Dash Diameter Diameter Pitch perSize Size (mm) (mm) (mm) inch

1/16" 1 7.723 6.561 0.907 281/8" 2 9.728 8.566 0.907 281/4" 4 13.157 11.445 1.337 193/8" 6 16.662 14.95 1.337 191/2" 8 20.955 18.631 1.814 143/4" 12 26.441 24.117 1.814 141" 16 33.249 30.291 2.309 11

1 1/4" 20 41.91 38.952 2.309 111 1/2" 24 47.803 44.845 2.309 11

2" 32 59.614 56.656 2.309 112 1/2" 40 75.184 72.226 2.309 11

3" 48 87.884 84.926 2.309 114" 64 113.03 110.072 2.309 115" 80 138.43 135.472 2.309 11

Nomina lDiamete r

Ø

HoseIns ide

Diamete rØ

BSPThread

/Threadspe r inch

Fema leBSP

Female135° BSP

Female90° BSP Male BSP Male BSPT

5 3/16” 1/8”-28 BSP101 BSP201 BSP301 BSP401 BSPT501








8 5/16” 1/2” BSP109 BSP209 BSP309 BSP409 BSPT509














20 3/4” 1” BSP111 BSP211 BSP311 BSP411 BSPT511

25 1” 3/4” BSP112 BSP212 BSP312 BSP412 BSPT512

25 1” 1” BSP113 BSP213 BSP313 BSP413 BSPT513

25 1” 1.1/4” BSP114 BSP214 BSP314 BSP414 BSPT514

32 1.1/4” 1.1/4” BSP115 BSP215 BSP315 BSP415 BSPT515

32 1.1/4” 1.1/2 BSP116 BSP216 BSP316 BSP416 BSPT516

40 1.1/2” 1.1/2” BSP117 BSP217 BSP317 BSP417 BSPT517

40 1.1/2” 2” BSP116 BSP216 BSP316 BSP416 BSPT516

50 2” 2” BSP117 BSP217 BSP317 BSP417 BSPT517

3 51 2 4

You measure theouter diameter at

The center of the thread

You measure theouter diameter in mm

MaleBSP


Female135° BSP

Female90° BSP

Fema leBSP

Ma leBSPT

BSP Fittings Part Numbers


HUBER S.A.

3

5

1 2 4




+30 (210) 3458126, 3475784

Fax: +30 (210) 3478074



Measuring UNF Threads of the JIC Fittings

You measure theInner diameter in inches

You measure theouter diameter in inches

UNFMale

UNF 135°FEMALE

UNFFemale

UNF 90°FEMALE

Example of enquiry

Our Client asks for : 10 pieces of hose type SAE100R2AT, hose, Inside Ø 3/4”, with 2 FittingsPart Number BSP122 and BSP322.Overall length 2 meters each.

Our Offer

We offer : 10 pieces hose type SAE100R2AT (our hose with 2 steel braids), Inside Ø 3/4” with2 fittings the first Female BSP and the second Female 90°.Overall L= 2 metres each.


UNF Thread Sizes

Male FemaleOuter Inner Threads

Nominal Diameter Diameter perSize inches inches inch

1/4” 0.25 0.2113 285/16” 0.3125 0.2674 243/8" 0.375 0.3299 247/16" 0.4375 0.3834 201/2” 0.5 0.4459 209/16” 0.5625 0.5024 185/8” 0.625 0.5649 183/4” 0.75 0.6823 167/8” 0.875 0.7977 141” 1 0.9098 12

1.1/8” 1.125 1.0348 121.1/4” 1.25 1.1598 121.3/8” 1.375 1.2848 121.1/2” 1.5 1.4098 12

UNF Fittings Part Numbers

Nomina lDiamete r

Ø

HoseIns ide

Diamete rØ

UNFThread

/Threadspe r inch

FemaleUNF

Female 135°UNF

Female 90°UNF Male UNF

5 3/16” 7/16”-20 UNF101 UNF201 UNF301 UNF401

5 3/16” 1/2”-20 UNF102 UNF202 UNF302 UNF402

6 1/4” 7/16”-20 UNF103 UNF203 UNF303 UNF403

6 1/4” 1/2”-20 UNF104 UNF204 UNF304 UNF404

6 1/4” 9/16”-18 UNF105 UNF205 UNF305 UNF405

8 5/16” 1/2”-20 UNF107 UNF207 UNF307 UNF407

8 5/16” 9/16”-18 UNFP108 UNF208 UNF308 UNF408

8 5/16” 3/4”-16 UNFP109 UNF209 UNF309 BSP409

10 3/8” 9/16”-18 UNF110 UNF210 UNF310 UNF410

10 3/8” 3/4”-16 UNF111 UNF211 UNF311 UNF411

10 3/8” 7/8”-14 UNF112 UNF212 UNF312 UNF412

12 1/2” 3/4”-16 UNF113 UNF213 UNF313 UNF413

12 1/2” 7/8”-14 UNF114 UNF214 UNF314 UNF414

12 1/2” 1.16”-12 UNF115 UNF215 UNF315 UNF415

12 5/8” 7/8”-14 UNF116 UNF216 UNF316 UNF416

16 5/8” 1.1/16”-12 UNF117 UNF217 UNF317 UNF417

20 3/4” 7/8”-14 UNF118 UNF218 UNF318 UNF418

20 3/4” 1.1/16”-12 BSP119 UNF219 UNF319 UNF419

20 3/4” 1.3/16”-12 BSP120 UNF220 UNF320 UNF420

20 3/4” 1.5/16”-12 BSP121 UNF221 UNF321 UNF421

25 1” 1.1/16”-12 BSP122 UNF222 UNF322 UNF422

25 1” 1.5/16”-12 BSP111 UNF211 UNF311 UNF411

25 1” 1.5/8”-12 BSP112 UNF212 UNF312 UNF412

32 1.1/4” 1.5/8”-12 BSP113 UNF213 UNF313 UNF413

32 1.1/4” 1.7/8”-12 BSP114 UNF214 UNF314 UNF414

40 1.1/2” 1.7/8”-12 BSP115 UNF215 UNF315 UNF415

50 2” 2.1/2”-12 BSP116 UNF216 UNF316 UNF416

1 2 3 4

HUBER S.A.





+30 (210) 3458126, 3475784

Fax: +30 (210) 3478074



Flanges Part Numbers

Nomina lDiamete r

Ø

InchØ

Flangeand the

outs ide Ø in mm

ASA 3000 PSIStra ight

ASA 3000 PSI135°

ASA 3000 PSI90°

Split Flange3000 PSI

12 1/2” 1/2” - 30.2mm ASA3-101 ASA3-201 ASA3-301 ASA3-401

12 1/2” 5/8” - 34 mm ASA3-102 ASA3-202 ASA3-302 ASA3-402

12 1/2” 3/4” - 38.1 mm ASA3-103 ASA3-203 ASA3-303 ASA3-403

16 5/8” 1/2” - 30.2 mm ASA3-104 ASA3-204 ASA3-304 ASA3-404

16 5/8” 5/8” - 34 mm ASA3-105 ASA3-205 ASA3-305 ASA3-405

16 5/8” 3/4” - 38.1 mm ASA3-106 ASA3-206 ASA3-306 ASA3-406

20 3/4” 1/2” - 30.2 mm ASA3-107 ASA3-207 ASA3-307 ASA3-407

20 3/4” 3/4” - 38.1 mm ASA3-108 ASA3-208 ASA3-308 ASA3-408

20 3/4” 1” - 44.5 mm ASA3-109 ASA3-209 ASA3-309 ASA3-409

25 1” 3/4” - 38.1 mm ASA3-110 ASA3-210 ASA3-310 ASA3-410

25 1” 1” - 44.5 mm ASA3-111 ASA3-211 ASA3-311 ASA3-411

25 1” 1.1/4” - 50.8 mm ASA3-112 ASA3-212 ASA3-312 ASA3-412

32 1.1/4” 1” - 44.5 mm ASA3-113 ASA3-213 ASA3-313 ASA3-413

32 1.1/4” 1.1/4” - 50.8 mm ASA3-114 ASA3-214 ASA3-314 ASA3-414

32 1.1/4” 1.1/2” - 60.3 mm ASA3-115 ASA3-215 ASA3-315 ASA3-415

40 1.1/2” 1.1/2” - 60.3 mm ASA3-116 ASA3-216 ASA3-316 ASA3-416

40 1.1/2” 2” - 71.4 mm ASA3-117 ASA3-217 ASA3-317 ASA3-417

50 2” 2” - 71.4 mm ASA3-118 ASA3-218 ASA3-318 ASA3-418

50 2” 2.1/2” - 84.1 mm ASA3-119 ASA3-219 ASA3-319 ASA3-419

Outside Ø mm

Dimensions and Part Numbers of ASA 3000 PSI

Flanges Part Numbers

Nomina lDiamete r

Ø

InchØ

Flangeand the

outs ide Ø in mm

ASA 6000 PSIStra ight

ASA 6000 PSI135°

ASA 6000 PSI90°

Split Flange6000 PSI

12 1/2” 1/2” - 31.7mm ASA6-101 ASA6-201 ASA6-301 ASA6-401

12 1/2” 3/4” - 41.3 mm ASA6-102 ASA6-202 ASA6-302 ASA6-402

16 5/8” 1/2” - 31.7 mm ASA6-104 ASA6-204 ASA6-304 ASA6-404

16 5/8” 3/4” - 41.3 mm ASA6-105 ASA6-205 ASA6-305 ASA6-405

20 3/4” 1/2” - 31.7 mm ASA6-107 ASA6-207 ASA6-307 ASA6-407

20 3/4” 3/4” - 41.3 mm ASA6-108 ASA6-208 ASA6-308 ASA6-408

20 3/4” 1” - 47.6 mm ASA6-109 ASA6-209 ASA6-309 ASA6-409

25 1” 3/4” - 41.3 mm ASA6-110 ASA6-210 ASA6-310 ASA6-410

25 1” 1” - 47.6 mm ASA6-111 ASA6-211 ASA6-311 ASA6-411

25 1” 1.1/4” - 54 mm ASA6-112 ASA6-212 ASA6-312 ASA6-412

32 1.1/4” 1” - 47.6 mm ASA6-113 ASA6-213 ASA6-313 ASA6-413

32 1.1/4” 1.1/4” - 54 mm ASA6-114 ASA6-214 ASA6-314 ASA6-414

32 1.1/4” 1.1/2” - 63.5 mm ASA6-115 ASA6-215 ASA6-315 ASA6-415

40 1.1/2” 1.1/2” - 63.5 mm ASA6-116 ASA6-216 ASA6-316 ASA6-416

40 1.1/2” 2” - 79.4 mm ASA6-117 ASA6-217 ASA6-317 ASA6-417

50 2” 2” - 79.4 mm ASA6-118 ASA6-218 ASA6-318 ASA6-418

Outside Ø mm

Dimensions and Part Numbers of ASA 6000 PSI

*The most common diameters for thesetype of fittings are marked in blue.

*The most common diameters for thesetype of fittings are marked in blue.



Documents

Spirou Patsi 67, 11855 Athens, Greece HUBER S.A.Spirou Patsi 67, 11855 Athens, Greece +30 (210) 3458126, 3475784 Fax: +30 (210) 3478074 Email: [email protected] HUBER S.A. Products