Embed Size (px)
Citation preview
Item No. 1
Specifications for Electrophoresis
Mini Protein Electrophoresis system (Dual)
Gel Size: 8x7cm
Spacers of 0.75 & 1.0mm thickness fused with glass plates, sample loading guides.
Two gel running capacity
Ridged combs 10&15 well
Optional preparative combs
Gel casting stand, no tapes or grease.
Submarine DNA Electrophoresis system
Single cast mould to prevent leakage
Mini-7x10cm gel tray UV transparent, 1.5mm and 1.0mm thick, 10x15 well comb, (2pairs) detachable
electrodes, 15x15cm UV Transparent gel tray, tape free gel caster alongwith casting gates. Optional
preparative combs.
Large: 15x25cm gel tray UV transparent gel Tray, 15, x20x30well 1.5x1.0mm thick combs (2each) Detachable
electrodes, 15x15cm UV Transparent gel tray, tape free gel caster alongwith casting gates, optional
preparative combs.
Power Supply: 5-200 V in I V step
200W maximum
Type of output: constant voltage or current with automatic crossover
Output terminals: 4 recessed sets in parallel
Timer: 0.999 minutes
Safety features: No load detection, ground leak detection, sudden load change detection, overload/short
circuit detection, auto power up after power failure.
ELISA Plate washer Item No. 2
Specifications
Ability to wash single strip of 8 wells as well as Whole plate
User programmable soak time, wash cycles and dispensing volume
On board two plate incubator at 37ºC with programmable timer
Washing Method : Plate and Strip Wash, Bottom and Overflow Wash, Rinsing, Priming
Multi step shaking
Quality Process Certifications ISO 9001:2008,ISO 13485:2003 ELISA Plate washer
Automatic Hematology Analyzer with essential accessories Item No. 3
Specifications:
At least 20 parameter with WBC 4-part differential or above for dog, cat, cow and horse, and atlease12 parameters for Rat and mouse
6 pre-set measurements for dog, cat, horse, cow, mouse & rat plus 3 users defined.
4 pre-set dilution mode (Normal, High, and Higher & Low) and in higher dilution mode, WBC range should be up to 0 to 599 × 103/μL.
Twin dilution sampling nozzles for reproducibility and accuracy
Double bath mixing chambers for effective hemolysing and Automatic sampling nozzle cleaning.
All the QC management to calculate, plotting data from the sample data & print as tabular form.
Hemolysing reagent should be cyanide-free.
Serial interface and USB interface for data transfer to a PC with optional Data Management Software,
Detection Method should comply, Electrical resistance detection, Surfactant method /colorimetric method and Histogram calculation platelet distribution width
Sample Volume: Around 30μL for normal mode, 10μL for high dilution mode & 10-20μL for capillary mode with built in pre-dilution facility.
Reproducibility of results( WBC: Within 2.0 % CV,RBC: Within 1.5 % CV, HGB: Within 1.5% CV, PLT: Within 4% CV
Display :colour LCD with backlight and touch screen keys for Numerical data, histograms and measuring conditions
Data Storage: Numerical data for all counted parameters for minimum 400 samples, and histograms for minimum 50 samples.
Operating temperature: 15 to 30°C, humidity: 30 to 85% (Non-condensing.
Power Requirements : 220 - 240 V ±10% AC
Printing Option: External Dot Matrix Printer OR internal Thermal Printer (both optional).
Micro Analytical Balance with the following specifications: Item No. 4
1. Readibility :- 0.01mg 2. Weighing Capacity:- 100 gm 3. Repeatability:- ± 0.05mg 4. Linearity:- ± 0.1 mg 5. Stabilization time: ≤ 3 sec. 6. Stabilizer (Compatible to bal ance)
Homogenizer with the following specifications : Item No. 5
1. Rotor speed range from 5000 upto 30,000 rpm. 2. Quick coupling for dispersing aggregates. 3. 4 interchangeable dispersing aggregates in EC design between approx. 0.1ml and
250 ml. 4. Control knob and speed scale.
5. Voltage 220V±10%
Specifications of Water Bath Item No. 6
1. Capacity: 18 litre or more
2. Temperature range: 5 to 99℃
3. Digital display of temperature
4. Easy to calibrate with user defined calibration points
5. With prefitted test tube racks and raised stainless steel shelves
6. Over temperature alarm.
7. Temperature Stability:±0.2℃
8. Flat lid with variable diameter holes to accommodate vessels.
9. To be supplied essentially with two years warranty
Specifications of Heating Dry Bath Item No. 7
1. Small foot print to accommodate in laminar or culture hood
2. Temperature Range : Ambient +2oC to 100oC
3. Time Range : 1 Min to 23 Hour 59 minutes
4. Temperature Precision : ±0.2oC or better
5. Uniformity of sample block temperature : ±0.5oC or better
6. Average heating rate : about 8-10 minutes to reach 60oC
7. Modular design of blocks to accommodate 0.2 ml to 50ML tubes and 96 well plates
8. Following blocks must be provided essentially with the machine:
24 well block for 0.2 ml tubes : 01 Nos.
12 well block for 0.5 ml tubes : 02 Nos.
6 well block for 1.5 ml tubes : 02 Nos.
6 well block for 2.0 ml tubes : 01 Nos.
6 well block for 15 ml tubes : 01 Nos.
3 well block for 50 ml tubes : 01 Nos.
96 well flat bottom block : 01 Nos.
9. Warranty of at least two years must be provided
Specifications of Multiplex Bead Array Biosensor System Item No. 8
Fully functional multiplex system for detecting at least 100 analytes per sample in a 96 well
microtitre plate format using magnetic or non-magnetic (polystyrene) bead based assays.
The multiplex bead array system should essentially include:
[I] Bead array reader:
1. Dual wavelength LED or Laser based optics and PMT or photodiode or CCD based
detection system to read fluorescence from 96 wells in less than 60 minute
2. Fluidics system to deliver sheath fluid without user intervention
3. Microtitre plate workstation for reading the 96 well plates
[II] Data work station and analysis software:
1. System should be supplied with latest configuration of PC available in the market at
the time of supply. Suitable LED/LCD monitor (atleast 22”), original / licensed
windows based operating system and branded colored laser printer to be provided.
2. Latest software package for data acquisition, data analysis and maintenance
functions of instrument.
3. Software must support instrument calibration and validation, protocol generation and
analysis of multiplex assay data.
4. Software must have provisions for organizing data from multiple data files, performing
common calculations/statistical tests, generate protocols and present results in
common graphical formats
5. Software should be supplied with atleast five user licenses for data analysis
[III] Calibration and validation kits
1. System should include maintenance plate for calibration and validation of instrument
2. The calibration and validation kits should be provided with system for ensuring
satisfactory performance of equipment.
3. These kits should be supplied for performing atleast 200 calibration assays and 24
validation assays
[IV] Automated bead washer
1. Standalone automated washer for washing the magnetic or non-magnetic
(polystyrene) beads
2. Vacuum manifold for washing filter bottom plates with compatible vacuum pump must
be either integrated in the washer or provided separately
[V] Consumables (as per details given below)
1. Flat bottom 96 well plates for using the magnetic bead based assays : 40 Nos.
2. Filter bottom 96 well plates for using the polystyrene bead based assays: 10 Nos.
3. Sheath fluid: Atleast 5 x 20L
4. Multiplex Bead array kit for simultaneously detecting atleast 10 Mouse cytokines
(Th1/Th2) in 5 x 96 samples
5. Multiplex Bead array kit for simultaneously detecting atleast 10 Rat cytokines
(Th1/Th2) in 5 x 96 samples
[VI] Essential Accessories (as per details given below)
1. All connecting cables and fluidic tubings
2. Spare set of air and fluid filters/seals sufficient for five years
3. Magnetic tube holder for holding atleast 12 microfuge tubes during coupling reactions
4. Tube rotator for holding atleast 12 tubes and capable of 360o rotation at variable
speed during coupling of beads
5. Hand held magnetic washer for washing the magnetic beads manually during
different steps
6. Non-refrigerated microfuge with variable speed upto 14000rpm to perform coupling
reactions on polystyrene beads
7. Variable speed microtitre plate shaker for mixing the beads with reactants
[VII] Original illustrated catalogue depicting the specifications of quoted model
must accompany the bid
[VIII] Users list: List of users in India and abroad for the quoted model must be
provided
[IX] Warranty: Atleast for two years from the date of installation
[X] Onsite Training: Bidder must provide free onsite application training to the users
[XI] Instruction manual of the machine for hardware and software should be
provided
Optional Accessories (To be quoted separately with prices mentioned for each item)
1. Carboxylated magnetic beads for developing custom assays: 1ML X 5
2. Carboxylated non-magnetic beads for developing custom assays: 1ML X 10
3. Amine coupling kit for about 120 reactions
4. Streptavidin – phycoeyrthrin conjugate : for 10 x 96 samples
5. Ultrasonic cleaner for cleaning the sample needle
6. Online UPS with atleast one hour power backup on full load
7. Split Air conditioner: 1.5 Tonne and five star rating
8. Any other accessory that will enhance the performance of the system
9. Different bead assay kits available for mouse, rats, canine and other species along
with other related consumables
Specifications of Protein Purification and Analysis System Item No. 9
System should be fully functional, automated chromatography system for protein purification
and analysis, consisting of following components:
1] UV Detector:
a. Multi wavelength detector for simultaneous detection of atleast three wavelengths
b. Detection range : 190 to ≥700 nm
c. Flow cells : 2MM, 5MM and 10MM
2] Conductivity monitor:
a. Built in conductivity monitor for monitoring the conductivity of buffer and samples
b. Conductivity Reading Range : ≤1 mS/cm to ≥ 800 mS /cm
c. Temperatures monitor range : ≤ 4oC to ≥ 90oC
d. Flow cell volume : ≤ 25ul
3] pH Monitor:
a. pH reading range : 0 to 14
b. Accuracy : ±0.1 pH unit
c. Flow cell volume : ≤ 100ul
4] System Pump:
a. Piston type pump
b. Flow rates : Upto 20 ml/min or more
c. Pressure Range : up to 20 Mpa or more
5] Mixer:
a. Mixing in chamber with magnetic stirrer to achieve gradient composition
b. Variable mixing volumes from 500ul to 5ml
6] Air sensors:
System must be provided with air sensors to enable sensing of end of buffer/sample in
order to protect from air entering the columns
7] Automated Fraction Collector:
a. Automated fraction collector compatible with the system for collecting the desired
fractions
b. The functioning of fraction collector must be software controlled
c. There must be option to collect fraction in tubes
d. Tube racks along with 15 and 50ML tubes should be provided
8] Column control valve:
a) System should be supplied with column control valve for connecting column and
should have bypass function to enable washing of system without removing
column.
b) The column control valve should allow reverse flow through the column for fast
and effective elution of strongly bound molecules
9] System Control and analysis software:
a) System should be supplied with user friendly, original software compatible with
the system for performing all types of chromatography applications
b) The software must allow control of entire instrument setup, method development,
real-time monitoring of run parameters including simultaneous display of multiple
wavelengths and data analysis
10] Pre-packed chromatography columns
Following columns must be supplied essentially with the system
a. Pre-packed, Ni charged resin column for affinity purification of His-tagged
recombinant proteins [1ML x 5]
b. Pre-packed, GST resin column for affinity purification GST-tagged recombinant
proteins [1ML x 5]
c. Pre-packed, protein-A or protein-G resin column for affinity purification of
antibodies [1ML x 5]
d. Pre-packed strong anion Exchange Column [1ML x 5]
e. Pre-packed strong cation Exchange Column [1ML x 5]
f. Pre-packed columns for separation of molecules in the range 0.5kDa to 70.0 kDa
[5Nos]
g. Pre-packed columns for separation of molecules in the range 5kDa to 400.0 kDa
[5Nos]
11] Refrigerated Cold Cabinet
System should be supplied with a refrigerated cold cabinet from reputed manufacturer
to house the entire protein purification system with accessories. The cold cabinet
should have following features:
a. Double door, approximately 1200Lit capacity or more
b. Interior and front panel made of stainless steel
c. CFC free refrigeration system and blower for air circulation
d. Fully insulated, front opening glass doors
e. Digital display of temperature
f. Temp range from +1oC to +8oC or more
g. Should have internal switch board for electrical connections
12] Data workstation:
System should be supplied with latest configuration PC available in the market with
original windows based operating system to install the software packages. Atleast 22”
flat LED/LCD monitor along with branded color laser printer to be provided
13] Other Essential Requirements:
a. All tubings, holders, clamps, filters and connection cables must be supplied
essentially to make the system fully functional.
b. Spare set of filters and any other hardware consumable required as replacement
for general maintenance of system should be provided in quantities sufficient for a
period of five years
c. Instruction manual of the machine for hardware and software should be
provided
d. Original illustrated catalogue depicting the specifications of quoted model
must accompany the bid
e. Users list: List of users in India and abroad for the quoted model must be
provided
f. Warranty: Atleast for two years from the date of installation on all components
g. Onsite Training: Bidder must provide free onsite application trainings to the
users
Optional Accessories (To be quoted with prices mentioned separately for each item)
1. Sample Pump
a. Sample pump must allow automated sample application for loading large
sample volumes to a column.
b. The sample pump must be equipped with pressure sensor
c. Metering type piston pump
d. Flow rates : Upto 50 ml/min or more
e. Pressure Range : up to 10 Mpa
2. Compatible 5KVA online UPS with atleast one hour power backup on full load
3. Split Air conditioner: 1.5 Tonne and five star rating to maintain ambient
temperature in laboratory
4. Different pre-packed chromatography columns and other related consumable
items. Following columns can be quoted as optional to select as per requirement
a. Pre-packed, Ni charged resin column for affinity purification of His-tagged
recombinant proteins [5ML x 5]
b. Pre-packed, GST resin column for affinity purification recombinant proteins
[5ML x 5]
c. Pre-packed, protein-A or protein-G resin column for affinity purification of
antibodies [5ML x 5]
d. Pre-packed strong anion Exchange Column [5ML x 5]
e. Pre-packed strong cation Exchange Column [5ML x 5]
f. Pre-packed columns for separation of molecules in the range 0.5kDa to 70.0
kDa [5Nos]
g. Pre-packed columns for separation of molecules in the range 5kDa to 400.0
kDa [5Nos]
5. Any other accessory that will enhance the performance of the protein purification
system
6. Accessories for analysis of proteins like mini and midi vertical gel electrophoresis
system capable to run atleast two gels simultaneously along with suitable power
pack, blotting apparatus: dot/slot blot etc.)
Specifications of Multi-Function Plate Reader Item No. 10
Fully functional multimode reader with following features to monitor absorbance, fluorescence, time
resolved fluorescence, luminescence and either fluorescence polarization or Fluorescence
Resonance Energy Transfer (FRET) in plates
1. Measuring Capabilities :UV/Vis absorbance, fluorescence, TRF and
luminescence
a. Absorbance Wavelength Range : ≤230 to 1000nm
b. Fluorescence Wavelength Range : ≤ 270 to ≥ 840nm
c. Luminescence Wavelength Range : ≤ 270 to ≥ 840nm
2. Reading capabilities : Different plates from 6 well to 384 wells
3. Light Source : Xenon Flash Lamp
4. Wave length selection : Monochromators in all measurement modes
5. Reading capability : Provision to read top or bottom of micro plate
6. Shaker : Provision for shaking sample compartment
7. Incubator : Temperature control of sample compartment
8. Temperature Range : From ambient + 5oC to ≥45oC
9. Measurement Speed : <30 seconds to read 96 well plate
10. Software package : Must include software for instrument control and data analysis
11. Data workstation : Must provide a branded PC with latest configuration available
in the
Market at the time of supply and atleast 22” flat LED/LCD
monitor along with branded color laser printer
12. Warranty : Atleast two years from the date of installation
13. Working voltage : 230/240 Volts, 50Hz
14. Original catalogue highlighting the desired specifications to be provided essentially
15. List of Users of the quoted model must be provided
16. Instruction manual of the machine for hardware and software should be provided
Optional Accessories:
1. Dispensers/Injectors:
a. Atleast two automated dispensers to dispense reagents in plates
b. Variable volume dispensing in 1ul increment
c. Dispensing syringe capacity of 500ul or more
2. Quartz plate of 8 x12 = 96 wells
3. Any other accessory to upgrade the system for better performance and measurement of
other related parameters
4. Compatible online UPS for atleast 30 minutes power backup
Specification of Automated Dispensing platform Item No.11
1. Fully functional and programmable, automated dispensing platform capable of dispensing reagents on solid surfaces like nitrocellulose membrane, glass slides etc.
2. Dispensing platform with high resolution syringe pumps to quantitatively dispense reagents in desired volumes with dispenser arms or dispensing platform moving in X, Y and Z directions.
3. There must be provision for mounting different dispensers on a motorized Z-axis for accurate adjustment of dispenser height to facilitate dispensing on different support matrix.
4. Dispensing area on the rectangular platform : Atleast 300 SqCm 5. Should have provisions for magnetic and vacuum manifold for holding membranes or glass
slides on the dispensing platform at the defined position 6. The dispenser should have inline degasser to prevent formation of air bubbles in the fluid
dispensing path 7. Provision for dispensing stock solutions from either conical bottom tubes or bottles or plates 8. There must be provision for dispensing liquids in the dots and line format using non-contact
type dispensers 9. Desired parameters in case of drop dispensing
a. Minimum volume per drop : ≤ 20nL b. Minimum diameter of drop : ≤ 0.3 MM
10. Desired parameters in case of line dispensing a. Continuous line mode b. Minimum width of line : ≤ 1.0 MM
11. Should be provided with controller and menu driven software to operate different syringe pumps, dispensers and instrument parameters
12. The controller should allow programming of dispensing volumes, variable speed movement of dispensers, line width, line length, dot / line format and pattern selection, dispensing or spraying applications etc.
13. The system should be supplied with atleast two programmable syringe pumps with syringes for simultaneously dispensing two different reagents from stock
14. Should be essentially provided with atleast two syringes of 500ul or more capacity 15. System must include atleast two non-contact type, on-board dispensers for dispensing liquids 16. There must be provision for attaching additional dispensers and different capacity syringes as
per requirements 17. All necessary accessories like tubings, filters, connecting cables etc. must be provided to
make the system fully functional 18. Power requirement: 230/240Volts and 50Hz 19. Warranty : Atleast two years from the date of installation 20. Original illustrated catalogue highlighting the desired technical specifications must be
provided with the bid 21. List of users of the quoted model to be provided 22. Company should have after sales service support in India (please give details of
sales/service office in India) Optional Accessories: [To be quoted separately with prices mentioned against each item]
1. Dispensers for contact dispensing of liquids 2. Additional non-contact dispenser 3. Dispenser for spraying/coating applications 4. Syringes of different capacities/volumes like 100ul, 250ul, 1000ul etc. 5. Compatible Vacuum Pump 6. Compatible de-humidifier/ humidity control system 7. Compressed air source : either air compressor or Nitrogen gas 8. Any other accessory that will enhance the performance of this system
Specifications of Fluorescence Microscope Item No.12
Fully functional Inverted Fluorescence Microscope for bright field and phase contrast microscopy along with camera and image analysis software
[I] Microscope Body
Microscope body with infinity optical corrected optical system with side port for attaching digital camera. Shock less construction with revolving or slider type Nosepiece to accommodate atleast four different objectives at a time.
[II] STAGE
Mechanical XY rectangular stage with specimen holders for multiwell plates, slides, dishes etc.
[III] CONDENSER
Universal turret or slider type condenser for different applications like bright field, phase contrast, differential interference contrast/integrated modulation contrast and fluorescence
[IV] ILLUMINATION SYSTEM
Halogen Illuminating pillar or LED based illumination
[V] OBJECTIVES
High performance long working distance objectives suitable for bright field / phase contrast/ fluorescence observation 4X, 10X, 20X, & 40X
[VI] OBSERVATION / EYEPIECE
Binocular or trinocular tube with 10X, anti-fungus type eyepiece along with dioptre adjustment facility
Microscope, camera and software should be preferably from same manufacturer for better compatibility
Warranty of at least two years should be provided
Should operate on single phase 220 volts and 50Hz power
[VII] Epi fluorescence attachment
1. With atleast 3 position filter block, for simultaneously attaching three fluorescence filters at a time
2. 100 watt fluorescence attachment
3. Following band pass fluorescent filters
a. Blue Filter for FITC/Alexa488 (Ex 465/30nm or 480/40nm and Em 515/40nm or 527/30nm)
b. Green Filter for TRITC/PE/Cy3(Ex 540/25, or 531/40 and Em 605/55 or 593/40)
c. UV Filter for DAPI/Hoechst (Ex 340/40 or 387/11 and Em 435/50 or 447/60)
[VIII] DIGITAL COLOR COOLED CAMERA
1. Digital Color Cooled CCD Camera capable of handling brightfield, fluorescence, DIC, and darkfield images
2. High resolution, atleast 5 mega Pixels camera with 2/3” CCD sensor with pixel size
of about 3.5um x 3.5um 3. Exposure time from 1msec to 500 Seconds or more 4. High Speed (24 or more frames per second) for fast live images. 5. USB port or fire wire cable for attaching camera onto desktop/laptop 6. All features of the camera should be software controlled for capturing images in
different microscopy techniques i.e Brightfield, fluorescence, DIC, darkfield images
[IX] IMAGE ANALYSIS SOFTWARE
1. Original software for capturing live image and analysis of captured image must be provided
2. Software should enable annotation, shading correction and image overlay functions. There must be provision to merge the images for generating multi fluorescence pictures
[X] DATA PROCESSING UNIT:
System should be supplied with latest configuration PC available in the market at the time of supply with original windows based operating system to install the software packages. Atleast 22” flat LED/LCD monitor along to be provided
OPTIONAL ACCESSORIES: (To be quoted separately with prices mentioned for each item)
1. Suitable compatible UPS with at least one hour power back
2. Spare100Watt fluorescence lamp
3. Separate narrow bandpass filter exclusively for viewing GFP fluorescence in the wavelength range Ex: 395 and Em: 509 to be quoted as optional
4. Separate narrow bandpass filter exclusively for viewing RFP fluorescence in the wavelength range Ex: 563 and Em: 582 to be quoted as optional
5. Other accessories that may enhance the performance of fluorescence microscope
Specifications of Vacuum Concentrator Item No.13 1. Centrifugal Vacuum Concentrator: Should be acid resistant, centrifugal vacuum
concentrator with solvent resistant glass lid and PTFE/teflon coated chamber to
accommodate tube and microtitre plate rotors
2. Microprocessor controlled cooling and heating system to achieve user selected
temperature in the range 0oC to 90oC or more
3. Provision for connecting concentrator to vacuum pump and cold trap through acid
resistant tubings.
4. Timer control and display of set as well as actual temperature
5. Brushless motor capable of achieving ≥ 1500 rpm centrifugal motion.
6. Vacuum delay function to achieve speed before applying vacuum.
7. There should be provision for allowing users to check sample status without stopping
the rotor and opening the lid of concentrator
8. Cold Trap: The concentrator must be supplied with cold trap having collector of
atleast 4 litre capacity to trap corrosive materials and solvents. There should be CFC
free refrigeration system to lower cold trap temperature upto -50oC or less.
9. Vacuum Pump: System must be supplied with a rotary vane pump with
displacement capacity of more than 100 L/min. About four litres of vacuum pump oil
along with adapters for connecting tubings must be provided.
10. Rotors: System should be supplied with following rotors:
a. Acid resistant Rotor to accommodate at least 60 tubes of 0.5/ 1.5/ 2.0 ML capacity
b. Acid resistant Rotor to accommodate at least 15 tubes of 15ML capacity
c. Plate rotor to accommodate at least 2 standard microtitre plates
11. Warranty: Atleast two years from the date of installation
12. Suitable voltage stabilizer must be provided
13. Original catalogue: of quoted model depicting technical specifications must
accompany the bid
14. Instruction manual of the machine for hardware and software should be provided
Optional Accessories: (Please quote the optional items with prices of each item
mentioned separately)
1. Chemical traps to provide additional protection of vacuum pump from corrosive
materials
2. Split air conditioner of 1.5 tonne capacity to maintain ambient working temperature
during concentration of samples under refrigeration condition
3. Chemical resistant two tier trolley to accommodate concentrator, cold trap and vacuum
pump
4. All other compatible rotors and accessories that will enhance the performance of
machine should be quoted
Specifications of Vertical Autoclave Item No.14
1. Fully functional, microprocessor controlled, vertical autoclave
2. Digital control of temperature and pressure for efficient steam pressure sterilization
3. Capacity : 40 litres or more
4. Temperature range: upto 122oC or more
5. Heater Power: 2 kW or more
6. Timer in hours and minutes
7. Display of set values and actual parameters
8. Internal chamber made of stainless steel and exteriors made of epoxy powder coated
steel or stainless steel
9. Must have pressure/vacuum guage
10. Top opening door with convenient single locking lid and effortless lifting of lid
11. Over temperature and over pressure safety feature
12. Castors for easy movement
13. Perforated stainless steel basket for keeping the autoclaving material
14. Supply voltage 230/240volts, 50Hz, single phase
15. Warranty: Atleast two years from the date of installation
16. Original illustrated catalogue highlighting the desired specification should be provided
with the bid
Specifications of Benchtop pH meter Item No.15
1. Fully functional benchtop, multiparameter device to measure the pH and temperature
of buffers/reagents
2. There should be large backlit graphic LCD showing measurements of temperature,
pH, along with electrode status, time/date and calibration data.
3. Provision for RS-232 or USB port for PC connectivity.
4. Automatic pH calibration with standard buffers and auto-buffer recognition
5. pH meter must be supplied with swing-arm electrode stand and power cord
pH range : ≤ 2.000 to ≥ 14.000
Temperature Range (°C) : 5 to ≥100
Temperature Accuracy (°C) : +/- 0.1 or better
pH Resolution : upto three decimals
6. Following electrodes must be supplied essentially:
a. Standard electrode with about 12mm diameter bulb - 02Nos
b. Micro electrode with about 5mm diameter bulb to measure pH of low volume
sample - 02 Nos
7. Working voltage 230/240 volts, 50Hz, single phase
8. Calibration buffers to cover acidic, neutral and basic pH range should be provided
9. Original illustrated catalogue showing desired features must be provided
10. Warranty: Atleast two years from the date of installation
11. Optional Accessories:
a. Other electrodes compatible with the pH meter to be quoted as optional with
prices mentioned separately
b. Polymer coated unbreakable electrodes
Specifications for Shaker Incubator (01 Unit) Item No.16
1. Orbital shaker incubator for mixing and incubating biological cultures
2. High quality stainless steel
3. Glass wool insulation
4. Temperature range: 10 to 60°C ± 0.5°C
5. Wave speed: 50 - 400 rpm ± 2 rpm
6. Digital control with LED display:
A. Time: 0-99hr with increment of 1 minute
B. Temperature: with increment of 1°C
C. Shaking speed: with increment of 1 rpm
7. Platform (approximately 40 cm X 40 cm) with clamps: 5 clamps for 250ml flask; 5 clamps
for 500ml flask and 4 clamps for 1000ml flask
8. Soft start and stop features to prevent culture spillage
9. Auto restart function after power interruption with non-volatile memory (retain set
parameters after power failure)
10. Open lid cut-out switch to stop platform motion
11. Audible/visible alarms for temperature (± 2°C) and speed deviation.
12. Unit should operate with 230V AC 50 Hz
13. Suitable voltage stabilizer
14. Warranty of three years.
Technical features should be supported by original literature & list of user
Specifications for Freeze Dryer (01 Unit) Item No.17
1. Microprocessor Controlled Laboratory scale freeze dryer with vacuum pump and facility for
lyophilizing the products in vials and ampoules, sealing under vacuum. The system should have
both automatic and manual operating system.
2. Ice condenser performance: Capable of removing at least 2 lit of water in 24 h and holding at
least 2.5 lit of ice before defrosting.
3. Ice capacity per day : 1 to 2.5 liters
4. Total ice capacity: 2 to 3.5 liters
5. Condenser temperature: -750C to -85
0C
6. Refrigeration: 2x1/3 Hp CFC free hermetically sealed compressor with suitable safety device
7. LC display of system operation and set parameters, viz., ice condenser temp, vacuum time set
8. Automatic defrosting function. Hot gas Frosting
9. Ice condensation chamber with high quality stainless steel inner condenser coils and drain valve.
Ergonomic condenser design to allow easy and quick cleaning, decontamination and defrosting.
10. Drying Chamber made of Stainless Steel with at least 16 ports for use of ampoule.
11. Freeze Dryer Manifold: comprising base plate/adaptor plate, three shelves, and distributors for
ampoules/vials. Freeze drying ampoules and vials of 2 to 5 ml capacity (500Nos) must be supplied
with system
12. System should have provision to start pump after condenser temp reaches -400C for safety
13. Vacuum Pump (quote Price separately): High quality corrosion resistant, direct driven,
double stage vacuum pump with gas ballast facility and safety valve capable of displacing at least
150 lits air per min for better performance. Pump should include exhaust filter, oil mist and odor
filter elements with a spare set. Ultimate Pressure should be at least 2x10¯ 3 mbar.
14. One split air conditioner of 2.0 tone capacity with suitable voltage stabilizer to maintain ambient
temperature for proper functioning of the unit.
15. Compact bench top design with small foot print. A trolley with wheels to keep the lyophylizer
unit, vacuum pump and accessories.
16. Safety device to protect vacuum pump from high temperature; oil and air back suction protection.
System must be quoted with Vacuum Grease, Vacuum Oil.
17. Complete sealing device for vials and ampoules.
18. Electricity requirement: 220-240V, 50Hz.
19. Ambient temperature: +10°C to +32°C
20. Noise level: ≤55dB
21. International Certification: FDA or equivalent, CE, NeP & ETL certified, ISO 9001 & GMP.
22. Servo voltage stabilizer compatible with the system.
Optional: to be quoted separately
Freeze drying ampoules and vials of 2 to 5 ml capacity
Data interface RS232 port for process documentation with PC of latest configuration must
be provided for installation of process documentation software.
Onsite warranty on the machine and accessories for at least two years from the date of installation
AMC charges for additional three years must be quoted separately.
Technical features should be supported by original literature
User list with their contact number and mail ID
Specification for projector and LCD/ILED Panels Item No.18
S. No Description Minimum Should be
Projection system 1 lens projector, Three LCD /LED panels (equal size about 55”-60” diagonally with remote, thin and light weight, Full HD resolution, integrated tuner and speakers, networking feature, various port like, VGA, HDMI, s-video)
1 Resolution 1280x800 dots or more
2 Contrast Ratio 3000:1 or more
3 Brightness 3000 ANSI lm or more
4 Short Throw Distance (Ceiling installation)
1 feet to 3 feet or better
Screen coverage 70" to 130" (measured diagonally)
5 Image Size / Projection Area 55 inches to 100 inches or better
6 Compatibility HDTV Formats (720p, 1080i, 1080p, 575i, 575p), Digital Input (HDMI), Personal Computers, Standard Video, Component Video
7 Aspect Ratio 16:10 (WXGA) or better
8 Interfaces Wireless network interfaces and other built-in interfaces
9 Lamp Life 5000 hrs or more
10 UPS 2 KVA offline with 30 min. backup
11 Remote power point presenter with laser pointer
Yes
12 Warranty 3 Years
Complete commissioning and Ceiling installation of Projector and wall installation of all three panels with Cabling, networking & other materials required
Specification For Somatic cell Counter/Analyzer Item No.19
Light Weight, portable (5-10Kg)
Analysis Time: <1min. per sample
Capacity: min.30 sample per hour
Measurement rang: min 10,000 upper limit; 30, 00,000 somatic cells/ml
Operating Temp.: 10 to 40°C
Sample temp.: 20°C to 60°C
Milk sample volume: 50 to 75µl in cassette
Repeatability: 7 to 10%
Power supply: 220v/50Hz
Minimum 1 year guarantee after installation on all parts.
The instrument should also work without computer
Facility for data transfer to an external Pc/Printer using USB connection
The tender should come with original brochure.
Cell counter with software and database kit for PC connectivity.
Cell counter will come in a bag with Battery.
2.0 KVA UPS of reputed make with batteries for minimum30 min back up.
This to declare that the specification list above, are generic in natures & does not reflect to any
particular brand in manufacture.
Optional: Additional cassettes for 1000 samples will be required.
: Rate for AMC for 5 years after the warranty period.
Food Product Forming machine Item No.20
Automatic Machine for forming products of different shapes and sizes from the mixture of variable amount of milk/coagulum
Forming of balls, nuggets, patties, biscuit like products etc.
Moulds for different shapes and sizes
Capacity to form 500 to 800 forms per hour
Hopper capacity- 5 to 10 kg
Facility to adjust weight of the products
All food contact area of high quality SS
Complete unit, easy to operate and clean
Complete fittings and installation
Warranty: Two years guarantee/warranty
Photograph/diagramme: Photograph of equipment along with all the detail specifications should be supplied.
User list: List of users with address, valid phone nos. and email Ids.
Chhana/Paneer preparation vat Item No.21
Milk loading capacity: 40-60kg
Made up of high quality SS-304
Jacketed with provision of hot water circulation
Completely equipped with agitator, knife and other attachments
Digital temperature indicator.
Provision for controlling the temperature
Inbuilt heating system
Complete fittings and installation
Warranty: Two years guarantee/warranty
Photograph/diagramme: photograph of equipment along with all the detail specifications should be supplied.
User list: List of users with address, valid phone numbers and email Ids.
Item No.22
ELISA Reader -Monochromator-Based Reader with following specifications
Detection mode UV-Visible Absorbance
Read method End-point, kinetic
Microplate types 1- to 384-well plates
(96 well and 384 well)
Shaking Yes
Software Data analysis software with Excel export
Control through USB or serial port
Automation Yes
Wavelength selection Monochromator
Wavelength range 230 - 900 nm, 1 nm increment
Bandpass 4 nm (230-285 m), 8 nm (>285 m)
Dynamic range 0 - 4.0 OD
Resolution 0.0001 OD, 0.0010D
Monochromator wavelength accuracy +2 nm
Monochromator wavelength
repeatability +0.2 nm
OD accuracy <1% at 2.0 OD typical
<3% at 3.0 OD typical
Temperature control 4°C above ambient to 45°C (+0.5°C)
User Interface On-board as well as PC control and support
UPS, dust covers and other required accessories
Specifications for Analytical Balance along with Stabilizer Item No.23
1. Built-in calibration mode with auto calibration on touch of a button
2. Capacity 150-210g with 90-120mm pan size
3. Tare range: Full to capacity
4. Readability: 0.001mg
5. Avereage response time: 5 sec or better
6. Wind draft shield; side & top opening shielding windows for easy pan access
7. Backlit digital display with sealed key pad
8. Operating voltage: 220 - 240V
9. Ambient conditions: 5 - 40°C; upto 85% humidity
10. Dust protection cover
11. Suitable voltage stabilizer
Original illustrated catalogue to support technical specifications & Users’s list
Two years on site warranty
Optional: USB2/RS-232 port computer interface with easy data transfer to Windows®XP/7 OS or better
based PC.
ELISA Reader with gradient filter cassette. Item No.24
Specification
MEASURING RANGE : 0 TO 3.000 Abs.
PHOTOMETRIC ACCURACY : +/- 1% or more
RESOLUTION: 0.001 Abs.
LIGHT SOURCE: Lamp Tungsten halogen with monochromator /Xenon with monochromator
OPTICAL SYSTEM: Grating Monochromator
WAVELENGTH RANGE: 370 nm to 850 nm standard continuously tunable
DETECTOR : Silicon Photodiode
DISPLAY: LCD
INTERFACE TO PC: Software for bidirectional use
POWER SUPPLY: 230 +/-10% VAC, 50 Hz
Accessories: Halogen Lamps (Two)
UPS: 2 KVa
Warranty for 2 years after installation.
Compatible desktop Computer with printer: and requisite software (s) for data reduction, multi-reduction, multi-level transformations, cut-off & validation formulas, flexible reporting options with sufficient data storage capacity and data output device.
Specifications of Digital Weighing Balance(02 Units) Item No.25
1. Monopan Balance with Glass partitions on all sides
2. Capacity : 220 GM or more
3. Readability : 0.1 MG
4. Repeatability : 0.2 MG or better
5. Linearity : 0.3MG or better
6. Average response time : 3 seconds or better
7. Tare Range : Full to capacity
8. Display : LCD display
9. Weighing pan : At least 80mm dia.
10. Weighing modes : grams, milligrams
11. Internal Calibration
12. Must have RS232 port
13. Balance must be ISO certified
14. Warranty of at least two years must be provided
15. Suitable stabilizer to be provided
Analytical Electronic Balance Weighing Balance Item No.26
Weighing cap. -- 200-230 g
Readability --- 0.1 mg
Repeatability ---- ± 0.1 mg
Linearity --- ± 0.2 mg
Pan Size ---- 80- 100 mm
With stabilizer 0.5 KVa
Three year warrantee
Desirable:
1.List of govt organizations supplied
2.Company Catalogoue
Bid should be supported with company catalogoue and list of research organizations supplied
ELISA Reader along with colored printer Item No. 27
Detailed specification;
● Wave length range 400-1000 nm
● Photometric range 0.0-4.0 OD
● Filters 8 position filter wheel
● Linearity ≤1.0% from 0.0-2.0 OD; ≤2.0% from 2.0-3.0 OD
● Accuracy ± 1.0% or 0.010 from 0.000-3.000 OD at 490 nm
● Precision ± 1.0% or 0.005 OD from 0.0-2.0 OD;
● Resolution 0.001 OD
Light source Tungsten halogen lamp average life hr. 3000 hr.
● Plate Types 96 well plate, plate height 16 mm. with flat, U, V shape bottom
● Linear shaking, built in shaker, three speed (low, medium & high)
● Duration second 0.999
Stability & drift < 0.10 OD at OD = 1 at 490 nm single wave length
● Read time 6 seconds at single wavelength, 10 seconds at dual wavelength
●Data output onboard graphical thermal printer and USB 2 interface
Equipment should be stand alone
● Data storage Calender / clock functions; 64 assay protocols
● print out report supported
● Motorized support for plate loading and retrieval
● Software;
High throughout analysis and reporting,
Comprehensive Curve- Fit Analysis, complex Kinetic Analysis
● 240 Volt, 50/60 Hz, Stabilizer 0.5 Kva
Optional- Coloured printer
● Three years warrantee; Three years service contract
Specifications of Bio safety Cabinet Type-III (2 Unit) Item No. 28
Bio- safety cabinet class-III
Should have total exhaust system with ducting.
Approximate interior Dimension (inches) of the cabinet : 25 H X 46 W X 24 D
Adjustable base stand with at least height of 30 inches.
All interiors and exterior should be of stainless steel.
Should have HEPA filters for supply and exhaust for particle size 0.3 microns.
Biological Safety cabinet should include the Zero Leak system, Drain Valve, Metal diffuser.
Work Tray should be easily removable for cleaning purpose.
Electronic airflow control system.
Should have florescent light and UV lights.
Vertical sliding view window w/8” working access and alarms.
Electrical circuits should have circuit breakers for safety.
Should include 1 electrical outlet and 2 service valves for air, gas or vacuum.
Provision of armrest for ergonomic comfort and glove port for transfer of hazardous samples and to avoid cross contamination.
Provision of Pass thru to provide easy transport of cultures and media without exposing to the environment.
ECM motor to increase filter life, lower energy costs and reduce noise and vibration.
Electrical requirement 230 V AV
Air Handling Unit (AHU) to provide temperature uniformity for handling mycobacterium spp.
Nanodrop Specifications Item No. 29
1. LCD Display
2. Wavelength range from 220 onwards upto 900 nm or more
3. Sample size less than 3 microliter
4. Wavelength accuracy 1nm
5. Measurement cycle time should be less than 10 seconds
6. Types of sample: For measuring absorbance of ss/ds DNA, RNA, Dyes,
proteins and other compounds and microbial cell culture OD
7. Electrical requirement: 220-240 volts, single phase, 50Hz to suit
local conditions
8. Data output can be obtained via a printer and a desktop with a compatible
stabilizer should be provided for data storage.
9. The specifications should be supported with original quoted model and its original
broacher.
10. TWO Years Warranty with on-site service as and when required
Item No. 30
Phase contrast Microscope with photo image device and thermostate.
Specifications:
Eye piece 10 X (Two pcs) with Diopter and eye guard, antifungal treated. Plan
achromatic objectives 10X, 20X, 40X & 100 X (oil), Course and fine adjustment.
Sextuple revolving nose piece with slot for POL/DIC slider. Condenser for bright field,
phase contrast and dark field microscopy or better. Illumination 12V, 100 W Halogen
lamp / LED lamp with inbuilt filters. Mechanical stage, ceramic coated. Digital
controlled stage warmer (ambient to 500 C) device with uniform distribution system.
Digital Camera at least 5 mega pixel. Soft ware for capturing images, storage, image
enhancement and measurement. Computer branded processor i 7, 2GB RAM, DVD
Writer, 320-500 GB or higher HDD, 17-18 inches TFT monitor along with UPS, fire
wire, optical mouse and key board. Microscope & Camera compatable should be
from same manufacturer.
Accessories: (optional); Halogen bulb- Two; Eye piece 10 X-one; Objectives 40 X, focusing telescope for phase contrast light, Immersion oil.
Trinocular Inverted research Microscope with camera and other accessories. Item No. 31.
Specifications
Trinocular tube with 30 W halogen illumination and camera attachment facility
Mechanical stage movement with roller guide right fitted handle
Fine and coarse focusing knobs with tension adjustment facility on coarse focusing
Bright-field condenser, Attachment filters for condenser
Plan achromatic anti-fungal objectives (10x, 20x, 40x, 100x)
Wide field Eye piece-antifungal lens (10x)
Spare bulbs 30 W halogen (4 Nos.)
Power cord, Dust cover/Dome shaped transparent cover
Focus should have coaxial coarse and fine focusing knobs.
Auto voltage selector.
Cross stage with flexible right handle
Up-gradable to fluorescent microscope
12 MP Digital camera with LCD display (1.8-2.5”)
>10 x optical zoom;
Built in pop-up type flash.
Built in Memory storage capacity 8 GB
Rechargeable NI-MH Batteries with charger and adapters etc.
Power adapters/cord for direct connectivity.
Memory storage cards (extra 2 Nos. 16 GB capacities).
Useful for field photography.
Adapters/attachments for microscopes, Cover/case
Any other feature adding to efficient working of the microscope may be included
Item No. 32
Biological microscope with digital camera with following specification:
1. Objective Lenses: quadruple objective revolving nosepiece. Plan Achromat 4x, 10x,
40x, 100x oil objectives.
2. Eyepieces: high eye point 10x eyepieces
3. Total Magnification: 100 - 1000x.
4. Focusable condenser
5. Focusing: Fine and coarse coaxial focusing.
6. Halogen illumination system.
7. With compatible digital camera.
Thermo mixer with 1.5ml Exchangeable block Item No. 33
Specifications
1. System should be able to provide peltier driven heating and cooling, with mixing. 2. Temperature range: 15° below ambient to 100°C, with minimum setting of 1°C 3. Sample block design should be easily removable for cleaning or replacement. 4. Mixing frequency: 300-3000rpm 5. Instrument should be specifically designed to take care of cross contamination, by making
sure spillage or lid wetting does not happen even at very low volumes 6. Timing range from 1min to 99h 7. Block Temp.accuracy and uniformity should be less than 10 C 8. Heating Time required should be less than 15 min (from 20 0C to 100 0C) 9. A heated top should be optionally available to prevent condensation on the lid or walls of the
tube. 10. Instrument should be able to recognize the blocks automatically and their respective speed
and temperature. 11. Soft keys for easy access to program parameters should be present 12. System should be stable on work bench even at the maximum speed with minimum noise
levels 13. The specifications of offered thermo mixer model should be supported by original broacher. 14. Warranty period minimum 2 years
Accessories should include
1. Thermo block of atleast 24 micro tubes in capacity of 1.5 ml. 2. Thermo block should be of atleast 48 micro tubes in capacity of 0.5 ml. 3. A voltage stabilizer from a reputed firm
Specifications for mini SDS and western blot apparatus assembly Item No. 34
Mini SDS-PAGE
Should have the capacity to hold at least 10-wells, gel of 1.0 mm thickness and should hold a gel size of
approximately 8 cm x7 cm.
Should have integrated spacers with glass plates for ease of casting.
Should include atleast 5 sets of compatible glass plates (spacer plate and shorter plates), a casting stand and 2
casting frames.
Should include all the accessories of SDS-PAGE gel including sample loading guide, electrode assembly, tank, lid
with power cables and mini cell buffer dam.
Should be a modular system to support blotting and electro-elutions also in the same system.
Powerpack
Should have output range of 10-300 V and 4-400 mA, fully adjustable.
Should have power of approx. 75W and time control of 001-999 minutes, fully adjustable.
Should have atleast 4 pairs of output jacks.
Operational voltage should be 220±20V
The power supply should be capable to operate four electrophoresis units simultaneously for identical runs
with LED display.
Type of out put – constant voltage and constant current
Auto power up feature after power failure should be there.
Western Blotting System
Should hold the gel size of upto 7.5x10 cm.
Should be compatible with the mini-SDS-PAGE gel apparatus.
Should include all the accessories required for Western blotting including buffer tank, buffer cooling unit,
electrode module, gel holder cassette, fiber pad and lid with power cables.
Should have the capacity to run 2 mini gels simultaneously.
Should come with Color coded cassettes and electrodes to ensure proper orientation.
Should come with cooling unit.
Should be a modular system.
Should provide user list with valid phone no and e mail ID
Should provide brochure in original.
Should provide operational voltage 220±20V
Specification: Bench top incubator shaker Item No. 35
Bench top incubator shaker with temperature control range from 7°C above ambient to 50°C
with accuracy ±0.1°C.
It should have orbital shaking.
Speed should be 50-350 rpm with accuracy of ±2rpm
It should have acceleration/deceleration circuit to prevent sudden starts/stops.
It should have timer up to 99 Hrs.
It should display speed, running time, alarm etc on display screen.
It should have alarms alert when speed or temperature deviate from set points.
The system should have port for data logging.
It should have automatic restart after power interruption.
It should stop agitation when chamber is open.
It should have universal platform and clamps to holds various flask.
It should be supplied with compatible stabilizer.
Operational voltage should be 220±20V
Should have two years standard warranty/from the date of installation
Should quote for the price of CMC/AMC per year after the expiry of standard warranty.
Should provide user list with phone no and e mail ID
Should provide brochure in original.
Specifications for Real Time PCR Item No. 36
1. Fully functional high throughput and fast Real-Time PCR system for qualitative and
quantitative detection of nucleic acids, mutation screening and SNP analysis.
2. It should be an open system capable of running different chemistries using TaqMan,
Molecular Beacon, SYBR green etc.
3. System should have 96 well block in plate format to accommodate 0.1/0.2 ml
tubes/strips/plate.
4. System should support reaction volume less than 30 µl.
5. Temperature range of thermal block should be preferably 4 to 99°C and temperature
accuracy should be about ±0.20 to 0.50° C.
6. System should support fast PCR protocol with ramp rate of preferably 4°C/sec or
more.
7. System should be capable of multiplexing with at least 5 different fluorescent
reporters.
8. System should be pre-calibrated for detecting at least five dyes (FAM/SYBR Green,
VIC/JOE, TAMRA, Texas red & CY5 or similar wavelength fluorophores).
9. It should have an LED or Tungsten Halogen excitation source with either photodiode
or CCD or PMT detector.
10. The software must allow analysis of multiple gene expression. The instrument
software must be capable of detecting and analyzing a different gene, SNP or
pathogen target in every well of the 96-well plate. Software should support performing
Absolute quantification, Relative quantification, Allelic Discrimination, Plus/Minus
assays. Along with this system should be able to conduct High Resolution Melting
(HRM) experiments for genotyping and mutation scanning experiments. The HRM
software must be provided essentially along with quoted system.
11. The vendor should have a functional laboratory and technical support team to support
and troubleshoot problems.
12. System should be supplied with three years warranty on all part including excitation
source (LED/lamp) and on-demand repair services as and when required.
13. Installation, testing, validation, demonstration/technical presentation should be
conducted. The vendor should provide comprehensive training on the operation of
the instrument, chemistry options and software. This training should be provided free
of cost with all the consumables required for demonstration.
14. The equipment should be supplied along with 1.5 ton (5 STAR rating) split air-
conditioning unit with appropriate stabilizer in order to maintain ambient temperature
while the equipment is functioning.
15. The following accessories must be supplied with the equipment:
Suitable on line UPS with a minimum 60 minutes power back up on full load.
A desktop computer of a reputed make having following configuration: Processor-
Intel Core i7 3rd gen., 4GB RAM, 500 GB HDD and at least 23 inch flat screen
LCD/LED monitor and a color laser printer with a licensed Windows 7 professional
OS and licensed original MS Office 2013.
Start-up consumables (including plasticware & chemicals) for 1000 reactions.
16. Indian user’s list for the quoted models along with complete contact details
including telephone no. & e. mail should be provided.
17. Technical features described above should exclusively be supported by authentic
original illustrated company catalog of the instrument/equipment quoted. Photocopy
or computer print-out of catalogue will not be accepted.
18. Vendor’s business record is to be authenticated by producing Income Tax return for
at least 3 consecutive previous years.
19. Optional accessories: Spare light source (LED/Tungsten halogen lamp) should also
be quoted separately as optional accessories.
SPECIFICATION FOR ULTRA CENTRIFUGE Item No. 37 Working Voltage == 220-230 Volts RPM / g – 100,000 RPM / 800,000g Easy Protocol Set up; Low Noise Level. LCD-Touch Screen Display. Rotar Tracking Facility ; Password Protected ; User Defined Programme Temperature 00 - 400.C Speed Control +/- 10RPM – Rotor Requirements :
(a) Angular
(b) Swing out with compatible tubes and adaptors.
(Please Quote Different Rotors with price individually Equipment should be supplied with two AC of 1.5 ton capacity)
Stabilizer : Good Quality Compatible and Robust.
5 Year Warranty / Guarantee for the main equipment.
User Lists and Other Detail
Accessories:
Different types of tubes/adaptors compatible to the rotors may be quoted with price mention separately for each item.
Server Item No.38
Server specification-
Intel Xeon Processor E5 2630(6 Core) 2.3 GHz/1333 MHz/ 15 MB Memory 4 x 8 GB,
HDD 3 x 300 GB SAS HDD, 2.5” Hot Swap, Multi Burner, RAID 05 in built (M5110 e card
+ 512 MB Cache) + RPS x 2 HS Component: Power Supply, Fan module, HDD Storage
Bays: 16 x 2.5” hot-swap drive bays or 8 x 2.5” hot-swap drive bays 1 x media bay Intel
USB port, I/O Slots: Riser Slot , IX PCI Express 3.00 x 8 (FH./FL)+ 2 x PCI Express 3.00 x
8 (HF/FL) , IX PCI Express 3.00 x 16 (FH/FL) + 1 x PCI Express 3.00 x 8 (HF/FL), IX PCI-
X(FH/FL) + 1 x PCI –X(FH/FL) + PCI Express 3.00 x 16 (HF/FL) with Key Board, Mouse
and 18.5” Monitor rack with complete accessory with three years onsite warranty.
