Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
Remote control battery installation
TINSEA348AWZZ
MODEL
HT-SB32D
SOUND BAR HOME THEATRE SYSTEM
This Quick Start Guide will help you to correctly install and operate your system.
Remote control × 1 RCA cable (2 pins - 2 pins) × 1
AC power lead × 1 Foot cushion × 4
AC/DC adaptor × 1 Wall mount angle × 2
Nut
(Spike + Nut) × 4 (Length: 25 mm) Pattern paper × 1
Accessories
Turn on your system
Before using remote control
Before using remote control, please remove plastic shield at battery holder.
Battery holder
Plastic shield
Remote control
1 Press the ON/STAND-BY button.
The sound mode indicator and display light up. If the power does not turn on, check whether the power cord is plugged in properly.
2 To set the unit to stand-by mode:
Press the ON/STAND-BY button again.The STAND-BY indicator turns red.
Polarity (+) symbol
Printed in Malaysia
11A R AS 1
1 Insert pin into the hole as shown and pull to open the battery holder.
Battery holder
Locking tabBattery type
Positive (+) side up
2 Remove the old battery from the battery holder, insert the new battery and then slide the battery holder back into the remote control.
Back of remote control
Pin
HT-SB250W250BK (QG).indd 1 12/29/2010 5:07:22 PM
Accessories
MUTE
ON/STAND-BY
MUSIC
CINEMA
NEWS
SURROUND
BYPASS
INPUT
TV CH
VOLVOL
RRMCGA32
2AWSA
SOUND MODE
Remote control x 1 AC/DC adaptor x 1(RADPA100AWZZ)
Optical cable x 1 Pattern paper x 1
Velcro tape (hook type) x 1 Velcro tape (loop type) x 2
HT-SB32D
AC power lead x 1 NFC tag x 1
Spike leg x 2
Before using remote controlBefore using the remote control, remove the plastic shield from the battery holder.
Remote control Plastic shield
Battery holder
Turn on your systemPress the ON/STANDBY button.The On/Standby/Input indicator lights up according to input source:Input source On/Standby/Input
indicator
OPTICAL IN Turns green
AUDIO IN Turns cyan
Bluetooth Turns blueNote:If the power does not turn on, check whether the power lead is plugged in properly.To set the sound bar to standby mode:Press the ON/STANDBY button again. The PAIRING indicator turns BLUE.
AC power connection
1 Plug the AC power lead into the AC/DC adaptor.
2 Plug the AC/DC adaptor cable into the DC INPUT socket on the sound bar.
3 Plug the AC power lead into a wall socket. The PAIRING indicator turns BLUE.
14G R AS 1TINSEA474AWZZ
Barcodesofthttp://www.barcodesoft.com
Barcode Symbology: Code 93 ; Font Facename: Code93MHr Data To Encode: TINSEA474AWZZ
Point Size 8 : *TINSEA474AWZZI3*|
Point Size 10 : *TINSEA474AWZZI3*| Point Size 12 : *TINSEA474AWZZI3*| Point Size 14 : *TINSEA474AWZZI3*|
Make sure to unplug the AC power lead before making any connections.
2
1
AC/DC Adaptor Cable
DC IN socket(DC 19V)
AC power lead
AC/DC Adaptor (AC 100 - 240 V ~ 50/60 Hz)
Wall socket
HTSB32_QG.indd 1 2014-07-07 08:56:37
To mount the sound bar on the wall1 Fix the pattern paper to the wall in horizontal
position as below.
44 mm
509 mmWall surface
Pattern paper (supplied)
548 mm
2 Make a hole on the wall following the screw point marks on the pattern paper by using a drill.
Wall surface
32 mm
8-9 mm
3 Fix a wall mount plug into the hole using a ham-mer, until it is flush with the wall surface.
32 mm
8-9 mm
Wall surface
4 Fasten the screws to the wall as shown below.(Total screw is 2 pieces)
Screw using
Wall surface
Wall surface
Screwdriver
4.5 mm - 5 mmGap from wall surface
5 Hang the sound bar onto the screws.
System preparation
1 Peel the double sided tape separator. 2 Fix the spike leg onto the sound bar as shown.
Make sure to unplug the AC power lead before installing the sound bar or changing the position.
Spike leg
Double sided tape separator Bottom of
sound bar
HTSB32_QG.indd 2 2014-07-07 08:56:38