Upload
others
View
5
Download
0
Embed Size (px)
Citation preview
SOM i.MX 8M User Manual NXP i.MX 8M™ based SOM | Rev. 1.0
EMBEDDED EDGE COMPUTING
SolidRun Ltd. 7 Hamada st. | Yokne'am Illit 2069201 | Israel www.solid-run.com
2
Revisions and Notes
Date Owner Revision Notes
Feb. 25th 2018 Noam Wiedenfeld 1.0 Initial release
Disclaimer
No warranty of accuracy is given concerning the contents of the information contained in this
publication. To the extent permitted by law no liability (including liability to any person by reason of
negligence) will be accepted by SolidRun Ltd., its subsidiaries or employees for any direct or indirect
loss or damage caused by omissions from or inaccuracies in this document. SolidRun Ltd. reserves the
right to change details in this publication without prior notice. Product and company names herein
may be the trademarks of their respective owners.
© 2018 SolidRun Ltd. All Rights Reserved.
Please verify that you have the most current version of this document from: www.solid- run.com
3
Table of Content Introduction ........................................................................................................................................................ 4
Overview ............................................................................................................................................................. 4
Highlighted Features .......................................................................................................................................... 4
Supporting Products ........................................................................................................................................... 5
Description ......................................................................................................................................................... 5
Block Diagram ................................................................................................................................................. 5
Feature Summary ........................................................................................................................................... 6
Core System Components .................................................................................................................................. 7
i.MX8 SoC Family ............................................................................................................................................ 7
Memory .......................................................................................................................................................... 8
10/100/1000 MBPS ETHERNET PHY ............................................................................................................. 10
WI-FI (11AC/B/G/N 2TX2R) TYPE 1216 AND BT 5.0 ...................................................................................... 10
MIPI CSI-2 CAMERA INTERFACE ................................................................................................................... 11
i.MX8 SOM External Interfaces ......................................................................................................................... 12
General ......................................................................................................................................................... 12
Supported Interfaces .................................................................................................................................... 12
Power and Reset ............................................................................................................................................... 23
Reset ............................................................................................................................................................. 23
i. MX8 SOM Integration Manual ........................................................................................................................ 24
Power up sequence ...................................................................................................................................... 24
Booting Options ............................................................................................................................................ 24
I2C Interfaces ................................................................................................................................................ 26
GPIO Interfaces ............................................................................................................................................. 26
i. MX8 SOM Debugging Capability ................................................................................................................. 26
i.MX8 Typical Power Consumption................................................................................................................... 27
i. MX8 SOM Mechanical Description ................................................................................................................. 28
Ordering Information ....................................................................................................................................... 29
5
Introduction
This User Manual relates to the SolidRun SOM i.MX8M series, which includes:
• Dual core ARM A53 (1.5 GHz) of the i.MX8M SoC.
• Quad lite core ARM A53 (1.5GHz) of the i.MX8M SoC.
• Quad core ARM A53 (1.5GHz) of the i.MX8M SoC.
Overview
The SolidRun’s SOM i.MX8M is a high-performance system on module (SOM) based on the
highly integrated NXP i.MX8M family of products.
Highlighted Features
• Ultra-small footprint SOM (47x30mm) including three board-to-board connectors (250 total pins number).
• NXP i.MX8M SoC (supports dual, quad lite and quad versions)
o Up to quad Cortex A53 and up to 1.5GHz
o Cortex-M4 subsystem processor supports real time tasks.
o Industry-leading audio, voice and video processing for applications
o OpenGL ES 3.1, OpenCL 1.2, OpenGL 3.0, OpenVG and Vulkan standards
• LPDDR4 memory in x32 configurations supports up to 4GB (Quad version)
• Power management devices
• Gigabit Ethernet interface based on Qualcomm Atheros 8031
• Wi-Fi (11ac/b/g/n 2Tx2R) + BT (V4.1 LE) M.2 Type 1216 based on Qualcomm Atheros QCA6174A-5.
• BT V5.0 based on Nordic’s nRF52832.
• PCIe clock generator supporting Gen2.
• 4-Lanes CSI connector for direct connection to a camera.
6
NOR
eMMC
Supporting Products
The following products are provided from SolidRun both as production level platforms and as
reference examples on how to incorporate the SOM in different levels of integration:
• HummingBoard Pulse– A board computer that incorporates the SOM retains the same
Android and different Linux distributions while adding extra hardware functionalities and
access to the hardware.
• CuBox-Pulse – A minicomputer that is only 2"x2"x2" in size that runs Android and Linux with
different distribution variants, use cases.
Description
Block Diagram
The following figure describes the i.MX8 Blocks Diagram.
10/100/1000 AR8031
GE PHY
RGMII 32 Bits Up to 4GB
USB1 (USB3/ USB2)
USB2 (USB3/ USB2) QSPIA, SS0
4K HDMI Level
adapter SDIO1, 8 Bits
PCIe 2
UART 1 (RX/TX) IMX-8M
I2C1
C
O
N
N
E
C
T
O
R
S
UART 2/3 (RX/TX/CTS/RTS)
ESPI2 SS0
I2C2/ I2C3
SDIO2 (4 BITS/ VSelect)
CSI 1 (2, 4 Lanes)
SAI2/3(TX/RX/TXC/MCLK/TXFS)
SAI1 (Full Bus)
GPIO
Boot Mode, Boot SEL
Reset, Conttrol
QUAD
QUAD Lite
DUAL
PCIe 1 WI-FI AC
EEPROM
UART 4 BT 5.0
CSI 2 (2, 4 Lanes) F
P
C
Cortex M4
3.3V
5V Power
3.3V PMIC
CLK2_O PCIe_CLK2
PCIe_CLK1
PCIe CLK
PCIe_CLK2 Buffer
WI-FI
7
Feature Summary
Following is the features summary of the SOM. Notice that some of the features are pinout
multiplexed (please refer to the pin mux table below and the NXP i.MX8M data sheets):
• NXP i.MX8M series SoC (Dual/Quad Lite/Quad ARM® Cortex™ A53 Processor, up to 1.5 GHz)
• Cortex-M4 subsystem processor.
• Up to 4GByte LPDDR4 memory
• Eight bits eMMC memory.
• QSPI NOR Flash memory.
• I2C EEPROM.
• HDMI 2.0a, HDMI 1.4 interface
• 4-lanes MIPI-DSI interface
• Two 4 lanes MIPI CSI-2 ()
• 10/100/1000 Mbps Ethernet PHY supporting 1588 standard (PPS output)
• Wi-Fi (11ac/b/g/n 2Tx2R) + BT (V4.1 LE) M.2 Type 1216 based on Qualcomm Atheros QCA6174A-5.
• BT V5.0 based on Nordic’s nRF52832
• Two USB 3.0 Host and OTG
• Two PCIe interfaces (PCIe-1 is available only if Wi-Fi is not in use).
• PCIe clock generator.
• Four bits SD interface
• Single eSPI interface.
• Up to three Synchronous Audio Interfaces.
• Up to three Serial interfaces.
• Required power sources:
o A single 5.0V interface
o 1.8/3.3V to support uSD card optional IO power.
8
Core System Components
i.MX8 SoC Family
The i.MX8M Dual / 8M QuadLite / 8M Quad processors feature advanced implementation of a quad
Arm® Cortex®-A53 core, which operates at speeds of up to 1.5 GHz. A general- purpose Cortex®-M4
core processor is for low-power processing.
The following figure describes the i.MX8 SoC’s main features (For more details refer to NXP’s
i.MX8 datasheet).
i. MX8 supports three variants; the following table describes the main differences:
9
LPDDR4
eMMC
Memory
The IMX-8 SOM support varieties of memory interfaces for booting and data storage. The following
figure describes the IMX-8 SOM memory interfaces.
Carrier SOM
LPDDR4
• Up to 4GB memory space (QUAD-Light and Dual up to 3GB).
• 32 Bits data bus.
• Up to 3200 MT/s.
• Supports D1, D2 and D4 die chips (Two CS).
• Support various low power modes, clock and power gated operation.
• Support Self-Refresh mode.
eMMC NAND Flash
• Up to 64GB memory space.
• 8 Bits data bus.
• Support MMC standard, up to version 5.0.
• Up to 1600 Mbps of data transfer for MMC cards using 8 parallel data lines in SDR
mode.
• Up to 3200 Mbps of data transfer for MMC cards using 8 parallel data lines in DDR
mode.
• IMX-8 uSDHC-1.
• Can be used as BOOT NVM *
USB2/3 32 Bits
NOR ESPI2, SS0
IMX-8 QSPAI, SS0
uSD SDIO2, 4 Bits QUAD
QUAD-Light
DUAL
SDIO1, 8 Bits
I2C1 EEPROM
EEPROM I2C2/3
NOR
10
Quad Serial NOR Flash (SOM)
• Each channel can be configured as 1/2/4-bit operation.
• Support both SDR mode and DDR mode
• No reset
• IMX-8 QSPIA/nSS0.
• Can be used as BOOT NVM *
EEPROM (SOM)
• 1Kb EEPROM
• ON-Semi’s CAT24AA01TDI or compatible
• IMX-6 I2C1
• Address 0X50 (7 bits format)
• Stores SOM’s configurations.
Micro-SD (Carrier)
• Optional on Carrier board
• IMX-8 uSDHC-1.
• Implements 4 data bits.
• Support SD/SDIO standard, up to version 3.0.
• Up to 400 Mbps of data transfer in SDR mode and up to 800 Mbps of data transfer in DDR mode using 4 parallel data lines.
• Can be used as BOOT NVM *
Serial NOR Flash (Carrier)
• Optional on Carrier board
• 1 bits data bus.
• IMX-8 eSPI2/nSS0
• Can be used as BOOT NVM *
*Please Note – All boot configuration signals are available on the SOM
connector.
11
2
D
C
o
n
n
e
c
t
o
r
10/100/1000 MBPS ETHERNET PHY
The Ethernet PHY is based on the Qualcomm / Atheros AR8031. The following figure describes
the Giga Ethernet interface.
P PS
M
• IMX-8 RGMII interface.
• IEEE 802.3 Ethernet interface for 1000BASE-T, 100BASE-TX, and 10BASE-Te.
• Atheros AR8031 PHY.
• Supports 1588 (PPS signal).
• 25M clock supports Synchronous Ethernet.
WI-FI (11AC/B/G/N 2TX2R) TYPE 1216 AND BT 5.0
The following figure describes the WI-FI and BT support in the IMX-8 SOM.
USB
SW
IMX-8
TX
RGMII REF_CLK
RX GE
AR8031
MDC/MDIO 25
25M
PHY &
MAG
C
o
n
n
e
c
t
o
r
PCIe
CLK Buff.
IMX-8 CLKO2
PCIe-1
UART-4 TX/RX
M.2 1216
11ac/b/g/n
+
BT 4.1 LE
BT 5.0
12
WI-FI
The WI-FI module is an M.2 1216 standard LGA module. The i.MX8 WI-FI module is Silex’s
WCBN3507A which based on Qualcomm Atheros QCA6174A-5 chip. The WI-FI main features are:
• Operate at ISM frequency Band (2.4/ 5 GHz)
• IEEE Standards Support 802.11ac, 802.11a, 802.11b, 802.11g and 802.11n
• IMX-8 PCIe-1 interface
• Enterprise level security supporting: WPA, WPA2
• Support 2 transmission and 2 receiving, transmission rate can up to 867Mbps(Physical Rate) in downstream and upstream
• USB2 connection is optional from carrier board to support BT over the M.2 module (*).
• Global certification.
BT 5.0
The i.MX8 SOM uses U-BLOX’s NINA-B111 module. The module is based on Nordic’s
nRF52832 BT SoC. The module main features are:
• Bluetooth 5.
• Advanced Serial Port Service.
• GATT server and client.
• Open CPU with Arm® Mbed™ and Nordic SDK.
• External antenna.
• Global certification.
Please Note: (*) the Silex M.2 module doesn’t support BT over UART.
MIPI CSI-2 CAMERA INTERFACE
The i.MX8 SOM supports a 4-Lanes MIPI CSI-2 interface. A 22 pins
FPC connector on the SOM board enables a direct connection to a
Camera supporting the CSI interface.
The connector pin-out is according to Allied Vision, a cameras
manufacturer. The figure to the right describes the interface
signals.
12
WI-FI
Resistor
Assembly
Option REF_CLK
REF_CLK
PCIe
CLK Buff.
C
o
n
n
e
c
t
o
r
• IMX-8 MIPI CSI channel 2.
• Implements all three CSI-2 MIPI layers.
• Scalable data lane support, 1 to 4 Data Lanes.
• Supports high speed mode (80Mbps - 1.5Gbps) per lane, providing 4K@30fpscapability for the 4 lanes.
• Virtual Channel support.
i. MX8 SOM External Interfaces
General
The SOM incorporates three Hirose DF40 board-to-board headers. The
selection of the Hirose DF40 is due to the following criteria:
• Miniature (0.4m pitch)
• Highly reliable manufacturer
• Availability (worldwide distribution channels)
• Excellent signal integrity (supports 6Gbps)
o Please contact Hirose or SolidRun for reliability and test result data.
• Mating height of between 1.5mm to 4.0mm (1.5mm to 3.0mm if using 70-pin Board- to-Board header). SR-SOM-MX6 headers are fixed, the final mating height is determined by carrier implementation.
Supported Interfaces
PCIe
The i.MX8 SOM supports two PCIe interfaces. The following figure describes the PCIe
interfaces.
IMX-8 PCIe-1
TX_M/P
RX_M/P
PCIe-1 REF_CLK X
PCIe-2
TX_M/P
RX_M/P
PCIe-2 REF_CLK
CLK2
13
The PCIe main features are:
• On board clock buffer sources all PCIe interfaces, on SOM and on Carrier.
• The IMX-8 CLK2_P/N clock output feeds the PCIe clock buffer.
• PCIe-1 can be used by the WI-FI module on the SOM or other module on the carrier. It is an assembly option.
• 1.5 / 2.5 / 3.0 / 5.0 / 6.0 Gbps Serializer / Deserializer.
• Compliant with PCI Express Base Specification 2.1.
• Supports Spread Spectrum Clocking in Transmitter and Receiver.
• x1 Gen2 lane.
• The PCIe TX signals are DC coupled by capacitors.
• The clock are HSTL compatible, no decoupling capacitors.
USB 3.0
The i.MX8 supports two USB 3.0 interfaces. The following figure describes the USB
interfaces.
C
o
n
n
e
c
RX_P/N t
DP/DN o
r
The USB main features are:
• USB 1 and USB 2 are directly connected to the connectors (No HUB).
• The TX signals are DC coupled by capacitors.
• Complies with USB specification rev 3.0 (xHCI compatible).
• USB dual-role operation and can be configured as host or device.
• Super-speed (5 Gbit/s), high-speed (480 Mbit/s), full-speed (12 Mbit/s), and low speed (1.5 Mbit/s) operations.
• Supports four programmable, bidirectional USB endpoints.
• OTG (on-the-go) 2.0 compliant, which includes both device and host capability. Super-speed operation is not supported when OTG is enabled.
• The USB 3.0 module operates in following modes:
IMX-8
USB1 TX_P/N
RX_P/N
DP/DN
USB1 VBUS
USB1 ID
USB2
TX_P/N
USB2 VBUS
14
o Host Mode: SS/HS/FS/LS
o Device Mode: SS/HS/FS
o OTG: HS/FS/LS.
• Power control signal are not part of the USB module, any available GPIO can be used.
MIPI CSI
The following figure describes the CSI interface.
CSI_LANE
CSI_LANE
CSI_LANE
CSI_LANE
CSI_CL
• i.MX8 MIPI CSI channel 1.
• Implements all three CSI-2 MIPI layers.
• Scalable data lane support, 1 to 4 Data Lanes.
• Supports high speed mode (80Mbps - 1.5Gbps) per lane, providing 4K@30fpscapability for the 4 lanes.
• Virtual Channel support.
MIPI DSI
The following figure described the DSI interface.
IMX-8
DSI_LANE0
C
o DSI_LANE1 n DSI_LANE2 n
DSI DSI_LANE3
DSI_CLK
e
c
t
o
r
The DSI main features are:
• Implements all three DSI Layers.
• Support for Command and Video Modes.
IMX-8
CSI 1
C
o
n
n
e
c
t
o
r
15
C
o
n
n
e
c
t
o
r
• Host Version.
• Scalable data lane support, 1 to 4 Data Lanes. (Optional bidirectional support on lane 0).
• Support for all DSI data types and formats.
• Virtual Channel support.
• MIPI Alliance Specification for Display Serial Interface Version 1.1 compliant.
Audio
The i.MX8 SOM supports up to three Audio channels, SAI1, SAI2 and SAI3. The following figure
describes the audio interface.
RXD, TXD, T/RXC, T/RXFS, MCL
RXD, TXD, T/RXC, T/RXFS, MCLK
SPDIF OUT
The Audio main features are:
• SAI1 supports 8TX and 8 RX channels.
• SAI2 and SAI3 supports RX and TX,
• SPDIF Out.
• Transmitter with independent bit clock and frame sync supporting 1 data line.
• Receiver with independent bit clock and frame sync supporting 1 data line.
• Each data line can support a maximum Frame size of 32 words.
For more details check the i.MX8 datasheet and AN.
Please Note: SAI1 signals are used as boot configuration during POR.
IMX-8 SAI1
SAI2
SAI3
SPDIF
16
HDMI
The i.MX8 supports the HDMI interface including the signal termination. The following figure
describes the HDMI interface.
The HDMI main features are:
• On board pull-up termination to support HDMI levels.
• HDMI HPD support 5V level,
• HDMI DDC doesn’t support PU, need to support on carrier board.
• Up to 4Kp60 video/graphics display over HDMI 2.0a with HDCP 2.2 encryption and audio formats including Dolby Digital, DTS, TrueHD, LPCM.
For more details check the i.MX8 datasheet.
Please Note: to support DPI, the pull-Up termination resistors are not
assembled.
17
UART
The i.MX8 SOM can support up to 4 UART interfaces. The following figure describes the UART
interfaces.
RX, TX (TerminaL
RX, TX,CTS, RT
RX, T
RX, TX Resistor4 - RX, T
Assembly
Option 2 – CTS, RTS
BT 5
MODULE
The UART interfaces main features are:
• UART 1 supports TX and RX. Can be used as debug terminal.
• UART 2 supports TX, RX, CTS and RTS. When using the RTS and CTS signals UART 4 is not available.
• UART 3 Supports TX, RX, CTS and RTS.
• UART 4 support TX and RX. It has an assembly options:
o On SOM BT module.
o Free UART on carrier board.
• High-speed TIA/EIA-232-F compatible, up to Mbit/s.
• 9-bit or Multidrop mode (RS-485) support (automatic slave address detection).
• 7 or 8 data bits for RS-232 characters, or 9 bit RS-485 format.
• Hardware flow control support for request to send (RTS_B) and clear to send (CTS_B) signals.
• RS-485 driver direction control via CTS_B signal.
• Auto baud rate detection (up to 115.2 Kbit/s).
• DCE/DTE capability.
For more information check the i.MX8 datasheet.
IMX-8 UART 1
UART 3
UART 2
UART 4
C
o
n
n
e
c t
o
r
18
eSPI
The i.MX8 SOM supports an eSPI interface. The following figure describes the eSPI
interface.
nSS0, MOSI, MISO, CLK
• i.MX8’s eSPI channel 2.
• Single chip select nSS0.
• Master/Slave configurable.
• Polarity and phase of the Chip Select (SS) and SPI Clock (SCLK) are configurable.
Please Note: eSPI channel 1 is not available as default configuration. The
signals supporting channel 1 are available as GPIO.
I2C
i. MX8 supports up to four I2c Interfaces. The following figure describes the I2C interfaces.
EEPROM
PMIC 1K
Camera
FPC
IMX-8 0x50
I2C1
I2C2
I2C3
The I2C main features are:
• I2C-1 is used only on the SOM. It is connected to the SOM EEPROM, PMIC and camera FPC connector.
• I2C-2 and I2C-3 are available on the connector by default.
• I2C-4 is not available as default configuration; it signals are available as GPIO.
• Multimaster operation.
• Software programmability for one of 64 different serial clock frequencies.
IMX-8
eSPI 2
C
o
n
n
e
c
t
o
r
19
• In Standard mode, I2C supports the data transfer rates up to 100 kbits/s.
• In Fast mode, data transfer rates up to 400 kbits/s can be achieved.
For more details check the i.MX8 datasheet.
uSD
The uSD supports the following features:
• i.MX8 uSDHC-1.
• Implements 4 data bits.
• Support SD/SDIO standard, up to version 3.0.
• Up to 400 Mbps of data transfer in SDR mode and up to 800 Mbps of data transfer in DDR mode using 4 parallel data lines.
• 1.8V or 3.3V support using SD2_VSELECT signal.
20
Connector’s Signal Description
J5001
PIN PWR Main GPIO PIN PWR Main GPIO
1 3V3 PMIC_ON 2
3 3V3 BOOT_MODE0 4 DSI_DN3
5 3V3 BOOT_MODE1 6 DSI_DP3
7 GND GND
8 GND GND
9
DSI_CKP
10 GND GND
11 DSI_CKN 12 DSI_DN0
13 GND GND 14 DSI_DP0
15 DSI_DN2 16 GND GND
17 DSI_DP2 18 PCIE1_REF_CLKP_CN
19 GND GND
20
PCIE1_REF_CLKN_CN
21
DSI_DN1
22 GND GND
23 DSI_DP1 24 3V3 PCIE_nPME gpio3.IO[5]
25 GND GND 26 3V3 PCIe_nWAKE gpio3.IO[12]
27 3V3 PWM1_OUT 28 3V3 USB1_SS_SEL gpio3.IO[15]
29 3V3 UART3_TXD gpio5.IO[27] 30 GND GND
31 3V3 UART3_RXD gpio5.IO[26] 32
PCIE1_TXP_C
33 GND GND
34
PCIE1_TXN_C
35 36 GND GND
37 3V3 UART3_CTS gpio5.IO[9] 38 PCIE1_RXP_C
39 3V3 UART3_RTS gpio5.IO[10] 40 PCIE1_RXN_C
41 3V3 SAI1_TXD2 (BT_CFG10) gpio4.IO[14] 42 GND GND
43 3V3 DSI_TS_nINT gpio5.IO[7] 44 3V3 UART2_RXD gpio5.IO[24]
45
46 3V3 UART2_TXD gpio5.IO[25]
47 GND GND 48 3V3 UART2_CTS uart4.RX/gpio5.IO[28]
49 50 3V3 UART2_RTS uart4.TX/gpio5.IO[29]
51 SAI1_TXD4 (BT_CFG12) gpio4.IO[16] 52 GND GND
53 WIFI_DP 54 CSI_P1_DN0
55
WIFI_DN
56
CSI_P1_DP0
57 GND GND
58 GND GND
59 CSI_P1_CKP 60 CSI_P1_DP2
61 CSI_P1_CKN 62 CSI_P1_DN2
63 GND GND 64 GND GND
65 CSI_P1_DP3 66 CSI_P1_DP1
67
CSI_P1_DN3
68
CSI_P1_DN1
69 GND GND 70 GND GND
J7
21
PIN PWR Main GPIO PIN PWR Main GPIO
1
PCIE2_REF_CLKP_CN
2
PCIE2_RXN
3
PCIE2_REF_CLKN_CN
4
PCIE2_RXP
5 GND GND
6 GND GND
7
PCIE2_TXN
8 3V3 SAI3_MCLK gpio5.IO[2]
9
PCIE2_TXP
10 3V3 SAI3_RXC gpio4.IO[29]
11 GND GND
12 3V3 SAI1_TXC gpio4.IO[11]
13 3V3 SAI3_TXFS gpio4.IO[31] 14 3V3 SAI3_TXC gpio5.IO[0]
15 3V3 SAI3_RXFS gpio4.IO[28] 16 3V3 SPDIF_TX gpio5.IO[3]
17 GND GND
18 3V3 IR_CAP gpio1.IO[12]
19
HDMI_TXP2
20 3V3 SAI1_TXD7 (BT_CFG15) gpio4.IO[19]
21
HDMI_TXN2
22 3V3 SAI1_TXD0 (BT_CFG8) gpio4.IO[12]
23 GND GND
24 3V3 SAI1_TXD1 (BT_CFG9) gpio4.IO[13]
25
HDMI_TXP1
26 3V3 SAI3_RXD gpio4.IO[30]
27
HDMI_TXN1
28 3V3 SAI1_TXD3 (BT_CFG11) gpio4.IO[15]
29 GND GND
30 3V3 SAI1_TXFS gpio4.IO[10]
31
HDMI_TXP0
32 3V3 nWDOG gpio1.IO[2]
33
HDMI_TXN0
34
35 GND GND
36 3V3 SAI1_MCLK gpio4.IO[20]
37
HDMI_CLKP
38 3V3 CLKO2 gpio1.IO[15]
39
HDMI_CLKN
40
41 GND GND
42 GND GND
43 3V3 HDMI_CEC
44
Tanya gpio5.IO[21]
45 5V HDMI_DDC_SCL
46
SAI1_RXD7 (BT_CFG7) gpio4.IO[9]
47 5V HDMI_DDC_SDA
48 GND GND
49 5V HDMI_HPD
50 3V3 SAI1_RXD5 (BT_CFG5) gpio4.IO[7]
51 3V3 SAI2_TXC gpio4.IO[25] 52 3V3 UART1_TXD gpio5.IO[23]
53 3V3 SAI2_TXD gpio4.IO[26] 54 3V3 UART1_RXD gpio5.IO[22]
55 3V3 SAI2_TXFS gpio4.IO[24] 56 3V3 USB1_ID
57 3V3 SAI2_RXD gpio4.IO[23] 58 GND GND
59 3V3 SAI2_MCLK gpio4.IO[27] 60
USB2_RXP
61 GND GND
62
USB2_RXN
63 3V3 SAI1_RXD6 (BT_CFG6) gpio4.IO[8] 64 GND GND
65 3V3 SYS_nRST
66
USB2_TXN
67 3V3 SAI1_RXD4 (BT_CFG4) gpio4.IO[6] 68
USB2_TXP
69 3V3 SAI1_RXC gpio4.IO[1] 70 GND GND
71 3V3 SAI1_RXFS gpio4.IO[0] 72 3V3 SAI1_RXD2 (BT_CFG2) gpio4.IO[4]
73 3V3 SD2_VSELECT gpio1.IO[4] 74 3V3 SAI1_RXD3 (BT_CFG3) gpio4.IO[5]
75 GND GND
76 GND GND
77
HDMI_AUXP
78 3V3 SAI1_RXD0 (BT_CFG0) gpio4.IO[2]
79
HDMI_AUXN
80 3V3 SAI1_RXD1 (BT_CFG1) gpio4.IO[3]
J9
22
PIN PWR Main GPIO PIN PWR Main GPIO
1
MDI_TRXN3
2 GND GND
3
MDI_TRXP3
4
USB1_TXP
5 GND GND
6
USB1_TXN
7
MDI_TRXN2
8 GND GND
9
MDI_TRXP2
10
USB1_RXP
11 GND GND
12
USB1_RXN
13
MDI_TRXN1
14 GND GND
15
MDI_TRXP1
16
USB1_DP
17 GND GND
18
USB1_DN
19
MDI_TRXN0
20 GND GND
21
MDI_TRXP0
22
USB2_DP
23 GND GND
24
USB2_DN
25 3V3 LED_10_100_LED_1000
26 GND GND
27 3V3 LED_ACT
28 3V3 USB_H1_PWR_EN gpio3.IO[4]
29 3V3 PPS
30 3V3 USB_OTG_PWR_EN gpio3.IO[2]
31 3V3 I2C3_SCL gpio5.IO[18] 32 3V3 ECSPI2_SS0 gpio5.IO[13]
33 3V3 I2C3_SDA gpio5.IO[19] 34 3V3 DSI_EN gpio5.IO[6]
35 GND GND
36 GND GND
37 3V3 CSI_nRST gpio1.IO[6] 38 3V3 SD2_CLK gpio2.IO[13]
39 3V3 AUD_nMUTE gpio1.IO[8] 40 3V3 SD2_CMD gpio2.IO[14]
41 3V3 CLKO_25MHz gpio3.IO[11] 42 3V3 SD2_DATA0 gpio2.IO[15]
43 5V USB1_VBUS
44 3V3 SD2_DATA1 gpio2.IO[16]
45 3V3 ECSPI2_MISO gpio5.IO[12] 46 3V3 SD2_DATA2 gpio2.IO[17]
47 3V3 ECSPI2_MOSI gpio5.IO[11] 48 3V3 SD2_DATA3 gpio2.IO[18]
49 3V3 ECSPI2_SCLK gpio5.IO[10] 50 3V3 SD2_nCD gpio2.IO[12]
51 3V3 I2C2_SDA gpio5.IO[17] 52 5V USB2_VBUS
53 3V3 I2C2_SCL gpio5.IO[16] 54 3V3 SAI1_TXD5 (BT_CFG13) gpio4.IO[17]
55 3V3 SWDCLK1
56
57 3V3 CLK_25M
58
59 3V3 SWDIO1
60
61 1.8/3.3V NVCC_SD2
62 3V3 ONOFF
63 3V3 3V3_OUT
64 3V3 SAI1_TXD6 (BT_CFG14) gpio4.IO[18]
65 3V3 3V3_OUT
66
67 3V3 3V3_OUT
68 3V3 PWM2_OUT gpio1.IO[13]
69 3V3 3V3_OUT
70 GND GND
71 5V VIN_5V0
72 GND GND
73 5V VIN_5V0
74 GND GND
75 5V VIN_5V0
76 GND GND
77 5V VIN_5V0
78 GND GND
79 5V VIN_5V0
80 GND GND
Power and Reset
23
The i.MX8 power is a single 5V source. It uses NXP’s PMIC and discreet power converter to source all
the i.MX8 power rails. The following figure describes the i.MX8 power architecture.
The power architecture main features are:
• Single 5V power source.
• NXP’s PF4210 source most of the IMX-8 power rails.
• Two discrete DC-to-DC converters source the CPU SOC and ARM powers.
• SNVS_3V3 can’t be power by a battery (No separate input).
• 3.3V output up to 2A (Need to calculate system and SOM power).
• Power up sequence is supported by the PMIC configuration.
Reset
The i.MX8 POR signal is activated by the PMIC output. The following figure describes the reset
architecture.
C
O
SYS_RST N N
E
C
T
3V3
VDD_SOC EN
PMIC_ON
PMIC POR
O nWDOG
R
POR
S IMX-8
A reset can be triggered by an external reset signal (Switch) or the internal Watch-Dog. Both signals
are OR to disable the VDD_SOC power source. The power source PG signal enables/disables the PMIC.
3.3V
C 5V DCDC BUCK NVCC_SNVS_3V3
3.38V/4A
O
N
N
E
C
T
O
R
S
SNVS_3V3
0.9V
PG Reset
DCDC BUCK
0.92V/3A EN
PMIC_ON
LDO
0.9V/0.3A
3.3V
PG
DCDC BUCK
0.99V/3A EN
VDDA_1V8
PMIC_ON
Conn.
NVCC_SD2
POR
3A Power
VDDA_1V8 EN Switch
24
i.MX8 SOM Integration Manual
Power up sequence
The IMX-8 is source by a single 5V input. Al power sequences are supported by the SOM.
When using the SOM 3.3V output there is no need to consider its power sequence. If an external
power source is used, it needs to be power according to the power sequence rules. (See IMX-8
datasheet for details)
Booting Options
Fuses Booting
The IMX-8 can boot from its internal fuses map. Booting from the fuses is enabled when the
BOOT_MODE[1..0] is set to “00”.
Booting From Resistors Settings
The i.MX8 SOM can boot from different NVM according to an external resistors configuration. The
boot from the resistors configuration BOOT_MODE[1..0] is set to “10”.
The available booting NVM are:
• eMMC on uSDH1.
• uSD card on uSDH2.
• QSPI on QSPIA.
25
The booting signals are SAI1RXD[0..7] and SAI1TXD[0..7]. The following table describes the
booting signals and its status during and after POR.
The following table describes how the booting signals need to be set to support the different
booting options.
Notes:
• NAND booting is not an option on the IMX-8 SOM.
• SPI NOR is an option on the carrier board (Not on the SOM).
• The configuration signals can be used as I/O or Audio interfaces after POR. Make sure that during POR it keep the booting requirements.
26
I2C Interfaces
The i.MX8 SOM uses I2C1 interface for its internal configurations. The following table describes
the address mapping.
Ref. Chip I2C Port Address A Port Address B Description
U15 PMIC 1 0 0 0 1 0 0 0 RW 08H IMX8 PMIC
U17 EEPROM 1 1 0 1 0 0 0 0 RW 50H EEPROM
GPIO Interfaces
The i.MX8 SOM uses some GPIO signals for it internal controls. The following table
describes the GPIO allocation.
Signal I/O Description Remarks
PCIE1_nCLKREQ gpio5.IO[20] Input from WI-FI module Active Low
WL_REG_ON gpio5.IO[5] Enable the WI-FI RF Active High
WL_nPERST gpio4.IO[21] Reset the WI-FI module Active Low
REF_CLK_32K gpio3.IO[3] 32K clock for the WI-FI module N.I.U.
UBLOX_RSTN gpio5.IO[1] Reset the BT module Active Low
ENET_nRST gpio1.IO[9] Ethernet PHY reset Active Low
ENET_WoL gpio1.IO[10] Ethernet Wake-Up signal Active Low
ENET_nINT gpio1.IO[11] Ethernet interrupt Active Low
PMIC_nINT gpio1.IO[7] PMIC interrup Active Low
i.MX8 SOM Debugging Capability
The IMX-8 SOM supports two main debugging interfaces:
• UART interface
• JTAG interface
The UART interface is a null modem interface that is internally pulled up and support using UART1
TX/RX signals.
he UART interface is optional to use and mentioned here since most of the
27
software infrastructure used in CuBox-Pulse and HummingBoard Pulse uses those two signals for
debugging.
JTAG interface is on the IMX-8 SOM and is exposed as test pins on component side. Following is a
snapshot of the test points and its connectivity traces:
TP-4 -> JTAG_nTRST. TP-5 -> JTAG_TDI. TP-6 -> JTAG_TMS. TP-7 ->
JTAG_TCK. TP-8 -> JTAG_TDO.
i.MX8 Typical Power Consumption
Setup 5V DC input power
consumption
Notes
Android idle TBD Performance governor, HDMI is on, USB,
eSata, WiFi and Ethernet are off
Android idle with Ethernet TBD Performance governor, HDMI is on, USB,
eSata, WiFi and Ethernet is 1Gbps
(note #1)
Android Nenamark2 benchmark TBD Performance governor, HDMI is on,
usb, sata, wifi and Ethernet are off
Full load - Android Nenamark2 benchmark
+ 4 processors running 100% (dd command
memory to memory)
TBD Performance governor, HDMI is on, USB,
eSata, WiFi and Ethernet is 1Gbps (note
#1). Tj is 55c
Full load - Android Nenamark2 benchmark
+ 4 processors running 100% (dd command
memory to memory)
TBD Performance governor, HDMI is on, usb, sata, wifi and Ethernet is 1Gbps (note #1). Tj is 87c (note #2)
Video 1080p Big Buck Bunny with AC3
audio codec (gstreamer from local SD)
TBD Performance governor, HDMI is on, USB,
eSata, WiFi and Ethernet are off
Linux idle TBD Performance governor, HDMI, USB,
eSata, WiFi and Ethernet are all off.
Linux suspend to memory TBD Note #3
28
i. MX8 SOM Mechanical Description
The following is a diagram of the TOP VIEW of the i.MX8 SOM.
Note the following details:
- The carrier board must use the same footprint as in the above mechanical footprint. Since this is a TOP VIEW of
the print side of the SOM i.MX8, the diagram above describes the dimensions and placement of the board-to-
board headers, mechanical holes and boundaries of the SOM i.MX8, as-is.
- J5002 is the main board-to-board header (bottom side in the diagram).
- J8004 is the second board-to-board header (upper side in the diagram).
- J5001 is the third board-to-board header (right side in the diagram).
- CuBox-i design does not use the mechanical holes, since the mating strength of two Hirose DF40 pairs and the
internal heat spreader is satisfactory for the design requirements.
- In case 1.5mm mating height was chosen, then the SOM i.MX8 requirement would be that all area beneath
it on the carrier will be all dedicated ONLY for the board- to-board connectivity; no other components are
allowed.
- In case higher mating is chosen, then 1.5mm should be reserved for the SR-SOM- MX6. For instance, if 3.5mm
mating height is chosen, then 1.5mm is dedicated to the SOM i.MX8 print side components and the remaining
2mm for the carrier components underneath the SOM i.MX8.
Refer to SolidRun HummingBoard and CuBox Pulse design and layout, where there are examples
of the main and second 80 pin header board-to- board usage.
29
Ordering Information
Please refer to the SolidRun website for more information regarding part numbers and the
procedure for placing an order.
http://www.solid-run.com