Solid State Relays Industrial, 1-Phase Analog Switching Type RM1E · 2018-10-03 · Specifications are subject to change without notice (06.09.2017) 1 • AC Solid State Relay •

Specifications are subject to change without notice (06.09.2017) 1

• AC Solid State Relay• Analog switching (phase-angle control) for resistive and slightly inductive load applications• 4 - 20mA or 0 -10V control input• Rated operational current: 25, 50, 75, 100 and 125 AACrms • Rated operational voltage: Up to 600 VACrms• Variable intensity LED-indication according to input current• Integral snubber network• Polarized lockable control connector for safe connection for voltage controlled version

Product De scrip tion The analog switching relay works in accordance with the phase angle control prin ci ple, i.e., the output switching point in the AC sine wave depends on the control input which can be either 4-20mA or 0-10VDC. 4 mA or 0VDC correspond to

zero output power whilst 20 mA or 10VDC correspond to full output power (near linear power response). The relay switches off every time the out-put cur rent cross es zero, and switches ON in ac cord ance with the ap plied control input.

Solid State Relays

Switching mode Rated operational Rated operational Control input voltage current

E: Analog switching 23: 230 VACrms* 25: 25 AACrms AA: 4 - 20 mADC 40: 400 VACrms 50: 50 AACrms V: 0-10VDC** 48: 480 VACrms 75: 75 AACrms 60: 600 VACrms 100: 100 AACrms 125: 125 AACrms* For nominal operational voltage of 110VACrms, use RM1E23...** RM1E..V.. require an external supply voltage

Type Selection

Rated Blocking Control Rated operational current op. voltage voltage input 25 A 50 A 75A 100 A 125 A

230 VAC 650 Vp 4 - 20 mA RM1E23AA25 RM1E23AA50 RM1E23AA100 RM1E23AA125 0-10 VDC RM1E23V25 RM1E23V50 RM1E23V100 RM1E23V125400 VAC 850 Vp 4 - 20 mA RM1E40AA25 RM1E40AA50 RM1E40AA100480 VAC 1200 Vp 4 - 20 mA RM1E48AA25 RM1E48AA50 RM1E48AA75 RM1E48AA100 RM1E48AA125 0-10 VDC RM1E48V25 RM1E48V50 RM1E48V100 RM1E48V125600 VAC 1400 Vp 4 - 20 mA RM1E60AA25 RM1E60AA50 RM1E60AA100 0-10 VDC RM1E60V25 RM1E60V50 RM1E60V100

Selection Guide

General Spec i fi ca tions RM 1E 23 ... RM 1E 40 ... RM 1E 48 ... RM 1E 60 ...

Operational voltage range RM1E..AA.. 90 to 280 VAC 340 to 460 VAC 200 to 550 VAC 410 to 660 VAC RM1E..V.. 90 to 265 VAC - 200 to 550 VAC 410 to 660 VAC Blocking voltage 650 Vp 850 Vp 1200 Vp 1400 Vp Operational frequency range 45 to 65 Hz 45 to 65 Hz 45 to 65 Hz 45 to 65 Hz Power factor > 0.75 > 0.75 > 0.75 > 0.75 Approvals UR, cUR, CSA, EAC UR, cUR, CSA, EAC UR, cUR, CSA, EAC UR, cUR, CSA, EAC

CE-marking Yes Yes Yes Yes*

* Heatsink must be connected to ground for 600V types

Industrial, 1-Phase Analog Switching

Solid State RelayNumber of PolesSwitching modeRated operational voltageControl inputRated operational current

Ordering Key RM 1E 60 AA 50

Type RM1E

RM1E..AA

RM1E..V

2 Specifications are subject to change without notice (06.09.2017)

RM1E...25 RM1E...50 RM1E...75 RM1E...100 RM1E...125

Rated operational current AC51 Ta=25 ˚C 25 AACrms 50 AACrms 75 AACrms 100 AACrms 125 AACrms AC53a Ta=25 ˚C 5 AACrms 15 AACrms 20 AACrms 20 AACrms 30AACrmsMinimum operational current 150 mA 250 mA 400 mA 400 mA 500 mARep. overload current t=1s 55 AACrms 125 AACrms 150 AACrms 150 AACrms 200 AACrmsNon-rep. surge current t=10ms 325 Ap 600 Ap 1150 Ap 1150 Ap 1900 Ap

Off-state leakage current < 3 mA < 3 mA < 3 mA < 3 mA < 3 mAI2t for fusing t= 10 ms 525 A2s 1800 A2s 6600 A2s 6600 A2s 18000 A²sCritical dV/dt off-state min. 1000 V/µs 1000 V/µs 1000 V/µs 1000 V/µs 1000 V/µs

RM1E

Input Spec i fi ca tions

RM1E..AA.. Current controlled input Control current range (A1-A2) 4-20 mADCPick up current 4.2 mADCDrop out current 4.1 mADCResponse time (input to output) ≤ 20 ms Voltage drop < 10 VDC @ 20 mADynamic impedance ≥ 330 ΩMax. allowable input current 50 mAReverse polarity protected Yes

Note: The use of twisted pair cable for the control input is recommended

RM1E..V.. Voltage controlled input Supply voltage, Vss (A3-A2) 24 VDC ±20%Max. supply current 15 mA @ 19.2 VDC 20 mA @ 30 VDCControl voltage, Vcc (A1-A2) 0-10VDCPick up voltage 0.2 VDCDrop out voltage 0.1VDCControl input current 0.15 mA @10 VDCResponse time (input to output) ≤ 20 msSupply reverse protected Yes

Output Spec i fi ca tions

Output Power Dissipation

0

20

40

60

80

100

120

140

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125

Pow

er d

issip

atio

n in

W

Load current per pole in AACrms

RM1E..25

RM1E.60..50

RM1E..100

RM1E..50

RM1E..75

RM1E..125


RM1E

Immunity EN60947-4-3

Electrostatic Discharge (ESD) Immunity IEC/EN 61000-4-2

Air discharge, 8kV Performance Criteria 2

Contact, 4kV Performance Criteria 2

Electrical Fast Transient (Burst) Immunity IEC/EN 61000-4-4

Output: 2kV, 5kHz Performance Criteria 1

Input: 1kV, 5kHz Performance Criteria 1

Electrical Surge Immunity IEC/EN 61000-4-5

Output, line to line, 1kV Performance Criteria 2

Output, line to earth, 1kV Performance Criteria 2

Output, line to earth, 2kV Performance Criteria 2 with external varistor

Input, line to line, 1kV Performance Criteria 2

Input, line to earth, 2kV Performance Criteria 2

Radiated Radio Frequency Immunity IEC/EN 61000-4-3 10V/m, 80 - 1000 MHz Performance Criteria 1 10V/m, 1.4 - 2.0GHz Performance Criteria 1 3 V/m, 2.0 - 2.7GHz Performance Criteria 1

Conducted Radio Frequency Immunity IEC/EN 61000-4-6 10V/m, 0.15 - 80 MHz Performance Criteria 1

Voltage Dips Immunity IEC/EN 61000-4-11 0% for 0.5 , 1 cycle Performance Criteria 2 40% for 10 cycles Performance Criteria 2 70% for 25 cycles Performance Criteria 2 80% for 250 cycles Performance Criteria 2

Voltage Interruptions Immunity IEC/EN 61000-4-11 0% for 5000ms Performance Criteria 2

EMC Emission EN60947-4-3

Radio Interference Voltage Emission (Conducted) IEC/EN 55011

0.15 - 30MHz Class A (industrial) with filters IEC/EN 60947-4-3 Class A (industrial) with filters

Radio Interference Field Emission (Radiated) IEC/EN 55011

30 - 1000MHz Class B

Electromagnetic Compatibility

Notes:- Control input lines must be installed together to maintain products’ susceptibility to Radio Frequency interference.- Performance Criteria 1: No degradation of performance or loss of function is allowed when the product is operated as intended.- Performance Criteria 2: During the test, degradation of performance or partial loss of function is allowed. However, when the test is complete the product should return operating as intended by itself.- Performance Criteria 3: Temporary loss of function is allowed, provided the function can be restored by manual operation of the controls.


RM1E

Housing Specifications Weight 25 A, 50 A Approx. 60 g 75 A, 100 A, 125 A Approx. 100 gHousing material Noryl, blackBaseplate 25 A, 50 A Aluminium 75 A, 100 A, 125 A Copper, nickel-platedRelay Mounting screws M5 Mounting torque 1.5-2.0 Nm

Functional Di a gram

IO

T1

L1

IC

(Brown) A3(+)

(Black) A2(-)

(Blue) A1(+)

RM1E..V..

RM1E..AA..

IO

A1(+) T1

L1A2(-)

IC

Connection Specifications

Stripping length (X) 12 mm 8 mm

Connection Type M5 screw with captivated washer RM1E..AA..: M3 screw with captivated washer RM1E..V..: 3 pins, pitch 2.54mm square pin 0.64’ Accessory: RCS3-100-1 terminated cable

Rigid (solid & stranded) UR rated data 1x 2.5 - 6.0 mm² 2x 2.5 - 6.0 mm² 1x 0.5 - 2.5 mm² 2x 0.5 - 2.5 mm² 1x 14 - 10 AWG 2x 14 - 10 AWG 1x 18 - 12 AWG 2x 18 - 12 AWG

Flexible with end sleeve 2x 1.0 - 2.5 mm² 1x 1.0 - 4.0 mm² 2x 2.5 - 4.0 mm² 1x 0.5 - 2.5 mm² 2x 0.5 - 2.5 mm² 1x 18 - 12 AWG 2x 18 - 14 AWG 1x 18 - 12 AWG 2x 18 - 12 AWG 2x 14 - 12 AWG

Flexible without end sleeve 2x 1.0 - 2.5 mm² 1x 1.0 - 6.0 mm² 2x 2.5 - 6.0 mm² 1x 18 - 10 AWG 2x 18 - 14 AWG 2x 14 - 10 AWG

Torque specification Pozidrive 2 Pozidrive 1

2.4 Nm (21.2 lb-in) 0.5 Nm (4.4 lb-in)

Aperture for termination lug 12 mm 7.5 mm

X X

X X

X X

X X

Connection terminals L1, T1 A1, A2


RM1E

Heatsink Dimensions (load current versus ambient temperature)With the output fully ON (360° conduction angle)

RM1E..25 RM1E..50

Operating temperature -20° to +70°C (4˚ to +158 ˚F)Storage temperature -20° to +100°C (-4˚ to +212 ˚F)Junction temperature ≤125°C (257 ˚F)

Thermal Spec i fi ca tions IsolationRated isolation voltage Input to output ≥ 4000 Vrms Output to case ≥ 4000 Vrms

RM1.60..50 RM1E...75

Load current [A]

Thermal resistance [°C/W]

Ambient temp. [°C]

TA

25.0 3.23 2.80 2.37 1.94 1.51 1.09

22.5 3.70 3.21 2.73 2.24 1.75 1.26

20.0 4.30 3.74 3.17 2.61 2.05 1.49

17.5 5.07 4.41 3.76 3.10 2.44 1.78

15.0 6.12 5.33 4.54 3.75 2.96 2.17

12.5 7.58 6.61 5.64 4.66 3.69 2.72

10.0 9.80 7.19 6.14 5.08 4.02 2.97

7.5 13.5 11.80 10.09 8.37 6.66 4.94

5.0 - 18.3 15.7 13.04 10.39 7.74

2.5 - - - - - 7

20 30 40 50 60 70

Load current [A]


Ambient temp. [°C]

TA

50.0 0.99 0.81 0.63 0.44 0.26 0.08

45.0 1.28 1.07 0.86 0.65 0.44 0.23

40.0 1.64 1.40 1.15 0.91 0.67 0.42

35.0 2.11 1.82 1.54 1.25 0.96 0.67

30.0 2.60 2.25 1.90 1.55 1.20 0.85

25.0 3.30 2.86 2.43 1.99 1.55 1.11

20.0 4.36 3.79 3.22 2.65 2.08 1.51

15.0 6.1 5.4 4.6 3.77 2.97 2.18

10.0 9.76 8.52 7.3 6.0 4.8 3.54

5.0 -- -- 15.47 12.85 10.24 7.6

20 30 40 50 60 70

Load current [A]


Ambient temp. [°C]

TA

50.0 1.25 1.07 0.88 0.70 0.52 0.34

45.0 1.46 1.25 1.04 0.84 0.63 0.42

40.0 1.73 1.49 1.25 1.01 0.77 0.52

35.0 2.08 1.80 1.51 1.23 0.94 0.66

30.0 2.56 2.22 1.87 1.53 1.18 0.84

25.0 3.24 2.81 2.38 1.95 1.52 1.09

20.0 4.26 3.71 3.15 2.59 2.03 1.47

15.0 5.99 5.22 4.45 3.67 2.90 2.12

10.0 9.49 8.27 7.06 5.85 4.64 3.43

5.0 - 17.5 15.0 12.4 9.91 7.39

20 30 40 50 60 70

Load current [A]


Ambient temp. [°C]

TA

75.0 1.00 0.88 0.75 0.63 0.50 0.38

67.5 1.15 1.00 0.86 0.72 0.57 0.43

60.0 1.33 1.16 1.00 0.83 0.66 0.50

52.5 1.56 1.37 1.17 0.98 0.78 0.59

45.0 1.88 1.65 1.41 1.18 0.94 0.71

37.5 2.33 2.04 1.75 1.46 1.17 0.87

30.0 3.01 2.64 2.26 1.88 1.51 1.13

22.5 4.16 3.64 3.12 2.60 2.08 1.56

15.0 6.46 5.66 4.85 4.04 3.23 2.42

7.5 13.42 11.74 10.06 8.39 6.71 5.03

20 30 40 50 60 70


Heatsink Dimensions (load current versus ambient temperature)

Dimensions

RM1E..100 RM1E..125Load current [A]


Ambient temp. [°C]

TA

100.0 0.60 0.52 0.43 0.34 0.26 0.17

90.0 0.74 0.64 0.54 0.44 0.34 0.24

80.0 0.91 0.79 0.68 0.56 0.45 0.33

70.0 1.09 0.96 0.82 0.68 0.55 0.41

60.0 1.33 1.16 1.00 0.83 0.66 0.50

50.0 1.66 1.45 1.24 1.04 0.83 0.62

40.0 2.16 1.89 1.62 1.35 1.08 0.81

30.0 3.01 2.64 2.26 1.88 1.51 1.13

20.0 4.73 4.14 3.55 2.96 2.37 1.78

10.0 9.94 8.70 7.45 6.21 4.97 3.73

20 30 40 50 60 70

Load current [A]


Ambient temp. [°C]

TA

125.0 0.63 0.55 0.47 0.40 0.32 0.24

112.5 0.73 0.64 0.54 0.45 0.36 0.27

100.0 0.84 0.74 0.63 0.52 0.42 0.32

87.5 0.99 0.87 0.74 0.62 0.50 0.37

75.0 1.20 1.05 0.90 0.75 0.60 0.45

62.5 1.48 1.30 1.11 0.93 0.74 0.56

50.0 1.92 1.68 1.44 1.20 0.96 0.72

37.5 2.65 2.32 1.98 1.65 1.32 0.99

25.0 4.12 3.60 3.09 2.57 2.06 1.54

12.5 8.55 7.48 6.41 5.34 4.27 3.21

20 30 40 50 60 70

RM1E

APPLYHEATSINK

COMPOUND

29.6

28.9

58.2

47

.5

44.8

12.3

5.2

2 x M5

1.84Pitch 2.54

LED

RM1E..AA RM1E..V

All dimensions in mm All dimensions in mm


Applications

RM1E

A2 (GRD)A1 (Vcc)A3 (Vss)

(Black)(Blue)(Brown)

0V0-10VDC+24VDC

4 to 20 mA

Iin

Uline Uline

RM1E..AA.. RM1E..V..A2

A1

L1 L1

T1 T1

Transfer CharacteristicsOutout power as a function of control output

This relay is suitable for control of heaters, lighting and slightly inductive loads such as small fans. The relay can also be used for soft turn-on of high-power incandescent lamps.

Control current (mA) Control voltage (VDC) Output power

4 0 0

8 2.5 25

12 5 50

16 7.5 75

20 10 99

• Heatsinks and fans• 5.40oC/W to 0.12oC/W thermal resistance• DIN, panel or thru wall mounting• Single or multiple SSR mounting

Heatsink Selection

Heatsink Range Overview:http://www.productselection.net/PDF/UK/ssr_accessories.pdf

Heatsink Selector Tool:http://www.productselection.net/heatsink/heatsinkselector.php?LANG=UK

Ordering Key RHS..


RM1E

Short Circuit ProtectionProtection Co-ordination, Type 1 vs. Type 2:

Type 1 protection implies that after a short circuit, the device under test will no longer be in a functioning state. In type 2 co-ordination the device under test will still be functional after the short circuit. In both cases, however, the short circuit has to be interrupted. The fuse between enclosure and supply shall not open. The door or cover of the enclosure shall not be blown open. There shall be no damage to conductors of terminals and the conductors shall not separate from terminals. Therese shall be no breakage or cracking of insulating bases to the extent that the integrity of the mounting of live parts is impaired. Discharge of parts or any risk of fire shall not occur.

The product variants listed in the table hereunder are suitable for use on a circuit capable of delivering not more than 65,000A rms Symmetrical Amperes, 600Volts maximum when protected by fuses. Tests at 65,000A were performed with Class J, fast acting: please refer to the table below for maximum allowed ampere rating of the fuse. Use fuses only.

Co-ordination Type 1 (UL508)Part No. Prospective short Max. fuse Class Voltage [VAC] circuit current [kArms] size [A]

RM1E..25.. 65 30 J / CC 600RM1E..50.. 65 30 J 600 20 HSJ20 (Mersen*) 600RM1E..75.. 65 100 J 600RM1E..100.. 65 80 J 600 60 HSJ60 (Mersen*) 600RM1E..125.. 65 125 J 600 60 HSJ60 (Mersen*) 600

Co-ordination Type 2 (IEC/EN60947-4-3)Part No. Prospective short Max. fuse Brand Model Size circuit current [kArms] size [A]

RM1E.xx.25.. (xx =23,40,48) 10 25 Mersen* 6.9gRB 10-25 10.3 x 38

RM1E.60..25.. 10 20 Mersen* 6.9gRB 10-20 10.3 x 38

RM1E.xx.50.. (xx = 23,40) 10 50 Mersen* 6.9zz CP gRC 14x51/50 14 x 51

RM1E.xx.50.. (xx = 48,60) 10 50 Mersen* 6.9zz CP gRC 22x58/50 22 x 58

RM1E.xx.75.. (xx = 23,40,48,60) 10 63 Mersen* 6.9zz CP gRC 22x58/63 22 x 58

RM1E.xx.100.. (xx = 23,40,48) 10 100 Mersen* 6.9zz CP gRC 22x58/100 22 x 58

RM1E.xx.100.. (xx = 23,40,48) 10 80 Mersen* 6.9zz CP gRC 22x58/80 22 x 58

RM1E.xx.125.. (xx = 23 or 48) 10 125 Mersen* 6.921 CP URGD 27x60/125 27 x 60

zz = 00, without fuse trip indication

zz = 21, with fuse trip indication

* Formerly Ferraz Shawmut


RM1E

Type 2 Protection with Miniature Circuit Breakers (M.C.B.s)Solid State Relay ABB Model no. for ABB Model no. for Wire cross Minimum length of type Z - type M. C. B. B - type M. C. B. sectional area [mm2] Cu wire conductor [m]* (rated current) (rated current)

RM1E..25.. 1-pole S201-Z4 (4A) S201-B2 (2A) 1.0 21.0 S201-Z6 UC (6A) S201-B2 (2A) 1.0 21.0 1.5 31.5 RM1E..50.. 1-pole S201-Z10 (10A) S201-B4 (4A) 1.0 7.6 1.5 11.4 2.5 19.0 S201-Z16 (16A) S201-B6 (6A) 1.0 5.2 1.5 7.8 2.5 13.0 4.0 20.8 S201-Z20 (20A) S201-B10 (10A) 1.5 12.6 2.5 21.0 S201-Z25 (25A) S201-B13 (13A) 2.5 25.0 4.0 40.0 2-poles S202-Z25 (25A) S202-B13 (13A) 2.5 19.0 4.0 30.4 RM1E..75.. 1-pole RM1E..100.. S201-Z20 (20A) S201-B10 (10A) 1.5 4.2 2.5 7.0 4.0 11.2 S201-Z32 (32A) S201-B16 (16A) 2.5 13.0 4.0 20.8 6.0 31.2 2-poles S202-Z20 (20A) S202-B10 (10A) 1.5 1.8 2.5 3.0 4.0 4.8 S202-Z32 (32A) S202-B16 (16A) 2.5 5.0 4.0 8.0 6.0 12.0 10.0 20.0 S202-Z50 (50A) S202-B25 (25A) 4.0 14.8 6.0 22.2 10.0 37.0 RM1E..125.. 1-pole S201-Z50 (50A) S201-B25 (25A) 4.0 4.8 6.0 7.2 10.0 12.0 16.0 19.2 S201-Z63 (63A) S201-B32 (32A) 6.0 7.2 10.0 12.0 16.0 19.2

* Between MCB and Load (including return path which goes back to the mains).Note: A prospective current of 6kA and a 230/400V power supply system is assumed for the above suggested specifications. For cables with different cross section than those mentioned above please consult Carlo Gavazzi’s Technical Support Group.


25

The declaration in this section is prepared in compliance with People’s Republic of China Electronic Industry Standard SJ/T11364-2014: Marking for the Restricted Use of Hazardous Substances in Electronic and Electrical Products.

Part Name Toxic or Harardous Substances and Elements

Lead(Pb)

Mercury(Hg)

Cadmium(Cd)

Hexavalent Chromium

(Cr(Vl))

Polybrominated biphenyls (PBB)

Polybrominated diphenyl ethers

(PBDE)

Power Unit Assembly x O O O O O

O: Indicates that said hazardous substance contained in homogeneous materials fot this part are below the limit require-ment of GB/T 26572.

X: Indicates that said hazardous substance contained in one of the homogeneous materials used for this part is above the limit requirement of GB/T 26572.

Environmental Information

环境特性

这份申明根据中华人民共和国电子工业标准SJ/T11364-2014：标注在电子电气产品中限定使用的有害物质

零件名称有毒或有害物质与元素

铅(Pb)

汞(Hg)

镉(Cd)

六价铬(Cr(Vl))

多溴化联苯(PBB)

多溴联苯醚(PBDE)

功率单元 x O O O O O

O:此零件所有材料中含有的该有害物低于GB/T 26572的限定。

X: 此零件某种材料中含有的该有害物高于GB/T 26572的限定。


Fork Terminals

• Terminal adaptors for 35mm2 cable• Type RM635FK• Pack size: 10 pieces

All accessories can be ordered pre-assembled with Solid State Relays.Other accessories include DIN rail adaptors, fuses, varistors and spacers.

For futher information refer to Accessories datasheets at:www.productselection.net/PDF/UK/SSR_Accessories.pdf

Other Accessories• Graphite thermal pad

with adhesive on one side

• Type KK071CUT• Dimensions: 35 x 43 x

0.25mm• Packing quantity: 50pcs.

• Touch safety cover• Type RMIP20• IP20 protection degree• Pack size: 20 pieces

Ordering KeyRM terminal adaptorTouch protected (optional)

RM635FK P

FASTON Terminals

• Faston tabs• Tab dimensions accord-

ing to DIN 46342 part 1• Pure tin-plated brass

RAM Solid State RelayFaston terminalsTab orientationInput Tab width: 4.8mmOutput Tab width: 6.3mm

Ordering KeyScrew mounted Faston terminals RM1E48V25 F 4

RS, RM Solid State RelayTab orientation

** 48: 4.8mm faston for input 63: 6.3mm faston for output

Faston terminals in packs of 20 RM48 F4

0: Flat (0º)4: Angled (45º)

*

Documents

Solid State Relays Industrial, 1-Phase Analog Switching Type RM1E · 2018-10-03 · Specifications are subject to change without notice (06.09.2017) 1 • AC Solid State Relay •