1

SmarterHome IP54 Battery Powered Fingerprint

Smart Wi-Fi Door Lock KASHFNGDLKA

Quick Start Guide

Table of Contents Installation ................................................................................................................................................................... 2 Using the App ............................................................................................................................................................ 7 Operation ....................................................................................................................................................................12 Specifications ........................................................................................................................................................... 13

2

Installation Note: Please have a Phillips-head screwdriver and 4x AA batteries on hand before installation.

1. It is recommended to have this installed by a professional. 2. Please note that the connection line shouldn’t be pressed, bent or folded during

installation. 3. Before the installation, ensure the lock is suitable for the door, or the direction of the

handle must be adjusted according to the door opening direction. 4. While installing, the door must be in a half-open state until the installation is complete. 5. After the installation is complete, test whether the front handle and back handle

unlock/lock normally. 6. If it does not work properly, please check if there has been an error during installation.

1. Installation Overview

1 Front panel 12 Connection column screws 2 Connection column 13 Reverse lock knob 3 Square steel 14 Back locking paddle 4 Lock body 15 Deadbolt 5 Connection line 16 Latch-bolt 6 Back panel 17 Lock body screws 7 ‘SET’ button 18 Connection column 8 Connection column screws 19 Keyhole 9 Battery cover 20 Emergency power port 10 Battery cover screw 21 Front handle 11 Back handle

3

2. Confirm the Direction of the Door This smart lock is suitable for 4 kinds of door opening directions (Left Out/Left In/Right Out/Right In).

3. Open Hole Drill correct holes in your door to facilitate installation. 4. Changing the Handle Direction 4.1 Check if the handle direction is appropriate for the door (facing left or right). If is not the correct direction, this can be changed with the following: 4.2 Front Handle Direction Change

• Disassemble the direction-changing screw, carefully and slowly twist the handle clockwise 180°, then retighten the direction-changing screw. Check the handle to make sure it isn’t stuck in place and can be used.

4.3 Back Handle Direction Change

• Disassemble the direction-changing screw, carefully and slowly twist the handle clockwise 180°, then retighten the direction-changing screw. Check the handle to make sure it isn’t stuck in place and can be used.

4.4 Match the front handle and back handle to make sure they are in the correct direction.

4

5. Installing Lock Body 5.1 Choose the installation direction of the latch-bolt of the lock body according to the door

opening direction.

5.2 Change the direction of the lock body.

a. Push the reversing block to the other side. b. Push the latch-bolt into the lock and turn it 180 degrees. c. Put back the reversing block and the latch-bolt will pop up automatically.

5.3 Put the lock body into the door frame and tighten with 2 fixing screws.

6. Choose the Parts Choose suitable parts according to the following table: Door thickness Square steel

length Connection column length

Connection column screw length

4-5.5cm 8cm 3.5cm 3cm and 5cm 5.5-6cm 8cm 5.5cm 3cm and 5cm 7-8cm 10cm 5.5cm 5cm and 7cm 9-10cm 12cm 5.5cm 7cm and 9cm >10cm (Optional)

14cm 5.5cm 9cm and 11cm

5

7. Installing the Lock 7.1 Installing the Front Panel

a. Install 2 connection columns on the front panel. b. Adjust the dot direction on the square steel sleeve with reference to the sticker on the

rubber mat a. Left open- keep the dot left or right b. Right open- keep the dot at the top or bottom

c. Insert the suitable square steel into the lock body. d. Pass the connection line through the door hole. e. Align the square steel with the square steel hole of the front panel and fix the front

panel on the door, then press the other end of the square steel.

7.2 Installing the Back Panel

6

a. Press the front panel and connect the connection line with the corresponding interface

of the back panel, then insert the excess line into the door hole. b. Insert the back-locking paddle into the lock body. You can cut off one or two sections

of the back-locking paddle according to the thickness of the door. Note: The length of the back-locking paddle should not exceed the thickness of the

door. c. Align the square steel with the square steel hole of the back panel and compress the

back panel. d. Lock with 2 connection column screws to fix the back panel. e. Install 4x AA batteries and the battery cover, then lock the battery cover with the

screw. Note: When installing the back lock, please look through the screw hole and make sure the connection wire is not blocking the connection column hole to avoid damaging the connection wire when installing the screw. 8. Installing Buckle Plate and Buckle Box

9. Debugging

a. Please always keep the door in a half-open status when debugging. b. Check whether the following functions can be achieved or not.

• Press down front handle: latch-bolt/deadbolt remains locked in locked status. • Press down front handle: latch-bolt/deadbolt retract in unlocked status. • Lift up front handle: dead bolt stretches out in any status. • Press down back handle: latch-bolt/deadbolt retract in any status. • Lift up back handle: dead bolt stretches out in any status.

c. When locking in reverse direction from inside, press down the front handle/back handle, the latch-bolt/deadbolt should not move.

d. Verify other functions are normal or not, including self-locking, virtual password, setting button, app remote unlocking etc.

7

Using the App Installing the App Download the “Kogan SmarterHome” app from the Play Store (Android) or App Store (iOS).

Creating SmarterHome Account

If you do not have a Kogan SmarterHome account, register or sign in with a verification code sent by SMS.

To register:

1. Tap to enter registration page. 2. The system automatically recognises your country/area. You can also select your

country code manually. Enter your mobile number/email address and tap “Next”.

If you choose the mobile number option, then enter the verification code sent to you by SMS. Set a password as prompted and press “Confirm” to finish your registration.

Create a profile on the next page to define your location and room.

8

Adding Device through Network

1. Power the SmarterHome device ON and follow the product-specific instructions to enter the Wi-Fi-connect mode.

2. Open Kogan SmarterHome app and tap “+” in the upper right to add a new device through the network.

3. Select the type of device you want to connect to on the next screen. 4. Ensure the device’s indicator light rapidly flashes and tap “Confirm light is rapidly

flashing”. 5. Select Wi-Fi network (Note: Network must be 2.4GHz band) and enter the password.

The device will commence the pairing process and connect to the app. • If needed, short press ‘3’ & ‘#’ on the lock to verify the administrator. • During connection, the LED for ‘8’ will flash quickly. • The Wi-Fi network of the app and device should be the same.

6. After successfully configuring the devices, the device will be shown on the home page. Tap to enter its control page.

• Once added successfully, a voice will sound saying ‘Added successfully’. • If addition has failed, an LED light will show ‘X’ and a voice will sound saying

’Add failure’. Please try to connect the unit again if this occurs.

9

To remotely open the door: a. Press ‘4’ and ‘#’ to activate the lock. b. Press the icon ‘Click open remotely’, when it flashes.

Google Home Control Adding “SmarterHome” to the Google Home App

Method 1:

Note: You will need to have set up a Google Home account prior to linking your Kogan SmarterHome device.

1. From the home screen of Google Home app, press the “Add” button. 2. Press “Set up device” and press “Set up or add”.

3. Under the “Works with Google” banner, tap “Have something already set up?” 4. Navigate to the magnifying glass search icon. 5. Search for “Smarter Home”.

10

Adding “SmarterHome” to the Google Home App

Method 2:

Note: You will need to have set up a Google Home account prior to linking your Kogan SmarterHome device.

1. Select “Menu” and then “Home Control”. 2. In the “Home Control” screen, select the + icon in the bottom right. 3. A list will appear showing actions and a search function to access more apps. From

here, install the SmarterHome app.

Using “SmarterHome”

1. Log into your SmarterHome account with your email address or mobile number. 2. Once linked, it will show the devices linked to your account, you can assign them to

rooms. You will be prompted to authorise apps to sync. 3. Click “Done” and then it will give you a list of commands available. 4. When successfully linked, you will see it on your “Home Control” screen at the bottom

of the app screen. You can now control your Kogan SmarterHome devices through Google Home.

11

Alexa Note: You will need to have set up an Alexa account prior to linking your Kogan SmarterHome device.

1. Select “Menu” and then “Skills”. 2. Search for the app and enable it.

12

Operation Using the Lock Adding the Administrator (The first 3 users are administrators)

1. Remove the battery cover, short press ‘Set’ (back panel) or long press ‘*’ and then a voice will prompt: ‘Please add administrator’.

2. Add the administrator’s fingerprint (3 times), card or password (6-8 numbers) followed by ‘#’ (the same password must be entered again as a confirmation).

3. A voice will say: ‘Added successfully’. 4. Then you can continue to add users.

Notes: 1. Different position fingerprints can be added to improve the fingerprint identification

rate. 2. ‘*’ is used as the back and sign out button, while ‘#’ is used as the confirm button.

Adding a User

An administrator is required to verify and assist in adding another user.

1. Remove the battery cover, short press ‘Set’ (back panel) or long press ‘*’ and then a voice will prompt: ‘Please verify the administrator’.

2. Verify the administrator. 3. Add the user’s fingerprint (3 times), card or password (6-8 numbers) followed by ‘#’

(the same password must be entered again as a confirmation). 4. The voice will say: ‘Added successfully’. 5. Then you can continue to add users.

Deleting a User

1. Remove the battery cover, short press ‘Set’ (back panel) or long press ‘*’ and then a voice will prompt: ‘Please verify the administrator’.

2. Verify the administrator. 3. Short press Set (back panel) or long press ‘*’ again. 4. Press ‘1’ to remove all user fingerprints, press ‘2’ to remove all user passwords, press ‘3’

to remove all user cards and press ‘4’ to remove all users. 5. The voice will then say: ‘Successful’. Note: The administrator can’t be removed by doing this, only normal users.

Modify Password 1. Press ‘7’ and ‘#’ and you will hear a long beep from the lock. 2. Enter the old password that is to be changed. The lock will prompt “Please add user”. 3. Enter the new password followed by ‘##’. The lock will then prompt “Successful”.

Note: The old password that was modified will be invalid after the change. Reset the Lock

1. Remove the battery cover, long press ‘Set’ for 3 seconds and verify the administrator. 2. The system will restore itself to factory default settings. Notes:

13

6 After the reset, all user and administrator information is removed. 7 The password will return to its default ‘1234567890’. 8 Please add a new administrator immediately.

Self-locking

If the password is entered wrong 5 times in a row, the system will be locked for 180 seconds (3 minutes). Using the fingerprint or card unlock can remove the self-lock. If the fingerprint is entered wrong 5 times in a row, the system will be locked for 180 seconds (3 minutes). Using the card unlock can remove the self-lock. Low Power Warning

When the battery power is lower than 4.8V, the lock will prompt ‘The battery is used up, please replace it’. Please replace with 4 new batteries soon after. Do not mix brands, or new and used batteries. Virtual Password

Enter a virtual password before or after the real password and it can then be unlocked. Volume Adjustment: Press ‘3’ ‘3’ ‘3’ ‘#’ to change volume (Mute, Low, Medium, High).

Doorbell: Press ‘#’ in the standby or initial state to sound.

Specifications Fingerprint sensor Semiconductor DPI 500 Identify time 0.3s Unlock way Fingerprint, Card, Password, Key and App System capacity 100 Supply voltage 6V Low voltage warning 4.8V Standby current <=50µA

User manual is subject to change without notice. For the latest version of your user manual, please visit https://www.kogan.com/usermanuals/