Your SMART Board 8070i-SMP interactive display includes the following:• four terminal connection panels, enabling you to connect

speakers, a dedicated in-room computer, a guest laptop, cabling for another guest laptop (installed solution) and other peripheral devices, such as DVD/Blu-ray ™ players and VCRs.

• a SMART Meeting Pro™ software download for the in-room computer.

• a SMART GoWire™ auto-launch cable with SMART Meeting Pro software to connect to a guest laptop.

• a CAT 5 USB extender to extend your USB connection up to 91' (28 m).

SMART GoWire cable

CAT 5 USB extender(CAT5-XT-1100)

SMART Board 8070i-SMPinteractive display

1

2

Dedicated in-room computer Guest laptop

a

Bottom terminal panel

Side laptop terminal panel

91' (

28 m

) max

.

c

f

VGA

Audio terminal panel

Speakers

Inside terminal panel

Power switch

HDMI

h

cb

d

e

smarttech.com

/kb/170166

Optional cables (not included)

Power (country-specific)a

SMART GoWire cablee

91' (28 m)

VGA

USBd

b CAT 5 USB extenderCAT5-XT-1100

Cat 5 f

k VGA to RGB/HV

RS-232 m

c

HDMIh

52' (16 m)

Cat 5 g

(×2)

SMART GoWire cablep

(×2)

CAT 5 USB extenderCAT5-XT-1100

n

Required cables (not included)

j DVI

HDMIh

Standard cable connections SMART Board® 8070i-SMP interactive display cabling guide

© 2012 SMART Technologies ULC. All rights reserved. SMART Board, SMART Meeting Pro, SMART GoWire, smarttech, the SMART logo and all SMART taglines are trademarks or registered trademarks of SMART Technologies ULC in the U.S. and/or other countries. All third-party product and company names may be trademarks of their respective owners. One or more of the following patents: US6320597; US6326954; US6563491; US6741267; US6803906; US6829372; US6947032; US6954197; US6972401; US7151533; US7236162; US7411575; US7619617; US7643006; US7692625; US7755613; US7757001; US7880720; USD612396; USD616462; USD617332; and USD636784. Other patents pending. Contents are subject to change without notice. 02/2012. 1017288 Rev 01

smarttech.com/support smarttech.com/contactsupport *1017288*

1

2

Dedicated in-room computer (USB 1) Guest laptop (USB 2)

a

Roomcontrol

Guest laptop (USB 3)

Bottom terminal panel

Side laptop terminal panel

52' (

16 m

) max

.

c

m

g

DVI

Audio terminal panel

Speakers

Inside terminal panel (For in-room computer)

Power switch

HDMI

h

VGA

k p

52' (

16 m

) max

.

n

n

g

n

n

e

HDMI

h

c

Remotely managing yourSMART Board™ 8070iinteractive displayConnecting your interactive display to an RS-232 system 2

Connection diagram 2Serial interface settings 3

Power modes 4RS-232 programming commands and responses 4

Interpreting the “invalid cmd” response 5Command inventory 5Designating video input source commands for a specific video input 6Designating a target interactive display 7

Commands and controls 8Power state commands 8Video input source 9Video source commands 10Audio output commands 13System information commands 14Service information 18

This document includes detailed instructions on how to set up your computer or room control systemto remotely manage your SMART Board™8070i interactive display using an RS-232 serial interface.

1

j

SMART Board™ 8070iInteractive DisplayUser's Guide

USB1/USB2 => HDMI/DVI Copyright SMART Technologies. All Rights Reserved.Header

Configuring the video and touch input for your SMART Board 8070i interactive display

OverviewYou can connect your SMART Board 8070i interactive display to up to three computers at once. Each computer must be connected to the interactivedisplay with a USB cable for touch input and a video cable for video input.

The following table shows the default touch input and video input pairings.

If you want to use a video and touch input pairing other than the default, you can change the video input settings in the Video and Touch Input Settingswindow of the SMART control panel.

N O T E

If multiple interactive displays are connected to your room computer, disconnect all but one of the interactive displays, and then configure the interactivedisplays one at a time.

Details

SMART hardware SMART Board 8070i interactive displays

SMART softwareSMART Notebook 10.8 SP1 collaborative learning software, SMART Meeting Pro 2.3 software and SMARTProduct Drivers 10.8

Operating systems Windows operating systems and Mac OS operating system software

Computer Touch input connection Default video input connection

Room computer USB 1 VGA

Guest laptop USB 2 RGB/HV

Side laptop USB 3 HDMI 2

Using the computer that’s connected to the USB 1 connection, configure the video input for each touch input connection using the Video and Touch InputSettings window.

I M P O R T A N T

You must have the latest version of SMART Notebook software or SMART Meeting Pro software installed on the computer connected to USB 1.

The interactive display status light must be green or flashing green.

The interactive display cannot be in Eco-Standby mode.

Page 1 of 3Configuring the video and touch input for your SMART Board 8070i interactive display (...

2/5/2012http://www.smarttech.com/us/Support/Browse+Support/Support+Documents/KB4/170065.a...

DVI

HDMI

DVI HDMI

h j

OR OROR

1

ExtendingUSB ConnectionsSMART Board® 800 series interactivewhiteboards and systems

91' (

28 m

) max

.g

smarttech.com/kb/160469

smarttech.com

/kb/170166

smarttech.com/kb/155317

smarttech.com/kb/170157

smarttech.com/kb/170065

smarttech.com

/kb/170166

smarttech.com

/kb/170166

Alternative cable connections