Upload
duongkhanh
View
231
Download
0
Embed Size (px)
Citation preview
Skylark Tiny III User Manual
一只云雀在云上翱翔
A skylark soars above the clouds.
WWW.SkylarkFPV.com
SATETY WARNING
SKYLARK OSD is for entertainment purpose only, users should bear all the risks
involved when using this electronics device.
Service center website: www.SkylarkFPV.com
Because the product function unceasing renewal, you hand user manual and the
actual content may try some. The latest user manual please from Skylark PPV
service center web site. This user manual is updated on March 20, 2012.
SKYLARK Tiny III OSD User Manual www.SkylarkFPV.com
Tiny III OSD User Manual
1.Main feature:
2.Main connection:
3.Packing list:1. Tiny III OSD board 1 pc
2. 60A Current sensor 1 pc
3. 10Hz GPS board 1 pc
4. GPS cable 1 pc
5. Current sensor cable 1 pc
6. User manual 1 pc
7. Reserve wire several pcs
1. Build in barometer.
2. Utra small and light.
3. Build in 60A Current sensor.
4. Online firmware upgrade.
5. Selectable OSD Screen.
6. 10Hz supper sense GPS with backup battery.
7. XT60 connector
8. Fly summarize
9. High precision current sensor
AV transmitter
12V
camera
Tiny III OSD
Voltage/Current sensor
SKYLARK Tiny III OSD User Manual www.SkylarkFPV.com
4.Tiny III OSD Connect with GPS、VOL/CUR Sensor:
Tiny III OSD connection operation:
1. According to on the picture above connected Tiny III OSD with GPS,
VOL/CUR Sensor (voltage current Sensor) .
2. RSSI / 5 V_IN/GND use 3 P line connected to the remote control receiver
of one of steering gear mouth, for Tiny III OSD provides 5 V power supply.
3. From the video camera will VideoIn output side, from the GND terminal GND
camera [camera needed another power supply].
4. VideoOut connected with the video of the transmitter graph input, GND
connected withthe GND terminal of the figure transmitter [ transmitter
needed another power supply ].
VOL/CUR Sensor
GPS
VOL/CUR Sensor
GPSTiny III OSD
Reset button
RSSI
5V IN
GND
GND
VIDEO
CAM
backside
SKYLARK Tiny III OSD User Manual www.SkylarkFPV.com
5.Setting:
Tiny III OSD Setting
LED lamp instructions:
1. When GPS properly connected and GPS work normal, LED by the output of
the GPS frequency flashing, for example, 10 HZ GPS, LED by 10 HZ frequency
blinking.
2. When not connected GPS or GPS unnormal, LED by 2 seconds to kill bright
show.
SKYLARK Tiny III OSD User Manual www.SkylarkFPV.com
6.OSD Screen:
[ standard screen ]
[ simple screen ]
SKYLARK Tiny III OSD User Manual www.SkylarkFPV.com
Displayed information description:
Description Display Range
Latitude N is North Latitude, S is South Latitude, Unit is Degree 90.0N~0~90.0S
Longitude E is East Longitude, W is West Longitude, Unit is Degree 180.0E~0~180.0W Numbers of GPS satellites
Numbers of GPS satellite that can be received signal currently.
0~9; 9 would be displayed even more than 9
Speed Total speed, unit is Km/ hour 0~999km/h
Current Operation current, unit is A 0.0~99.9A
Voltage System voltage, unit is V. it would flash when under voltage. 0.0~99.9V
Electricity consumption
The electricity consumed from system start-up till now, unit is mAH
0.0~9999mAH
Remaining electricity
The battery symbol indicates the remaining electricity level, when it is nearly used up, the symbol would flash.
It takes a 2200mAH battery as indication standard.
Point of departure Indicate the point of departure Location & direction The plane icon indicates the existing location & direction
corresponding to the point of departure. Up: North, Down: South, Left: West, Right: East. The flying direction is shown by the plane icon.
Altitude corresponding to the point of departure
Altitude that corresponding to the point of departure. The figure can be negative, unit is meter.
-9999~9999m
Returning angle & direction
Indicate the required angle and direction for a returning journey, the unit for angle is degree. When angle is less than 5 degree, it would consider as accurate, so direction would not be displayed.
Horizontal distance corresponding to the point of departure
The horizontal distance corresponding to the point of departure, the unit would be adjusted automatically.
0~99.9km
Signal indication of remote control
When the device is under interference and out of control range, it would flash.
Flying time The flying time is accumulated from the first take-off. When there are 4 or more GPS satellites and the speed exceeds 5m/s the first time, it starts counting.
Description Display Range
SKYLARK Tiny III OSD User Manual www.SkylarkFPV.com
7.Skylark Tiny III OSD Setting:
1. Click OSD->ScreenSet
Skylark Tiny III OSD RSSI Calibration
1. Make sure the RC receiver RSSI is connected to the OSD board.
2. Use the Skylark USB Cable connect your computer and the GPS port of the Tiny
OSD board
3. Remote Control power on
4. RC receiver power on
5. Run Configuration Software
6. Click OSD->Calibrate
7. Click "Start" button
SKYLARK Tiny III OSD User Manual www.SkylarkFPV.com
8. Remote Control power off
9. Click "Stop" button
SKYLARK Tiny III OSD User Manual www.SkylarkFPV.com
10. Remote Control power on
SKYLARK Tiny III OSD User Manual www.SkylarkFPV.com
8.Skylark Tiny OSD Upgrade:
Download
Upgrade
Skylark Configuration Software
Tiny OSD Firmware
1. Download rhe Skylark Configuration Software and the Tiny OSD Firmware V1.6
2. Unzip the SkylarkSetup V2.0.zip
3. Double click the SkylarkSetup V2.0.exe and install the software to your computer
4. Use the Skylark USB Cable connect your computer and the GPS port of the
Tiny OSD board
5. Unzip Tiny firmware V1.6.zip
6. Double click SkylarkFPV icon on your computer desktop