Embed Size (px)
Citation preview
ALUMASC EXTERIOR BUILDING PRODUCTS LTD
Tel: +44 (0)1744 648400 Email: [email protected]
Website: www.alumascwaterproofing.co.uk Ref: SD010FR Issued: 01/06/12 Page 1 of 2
Euroroof MonoSingle Layer Cold-Applied Bituminous Warm Roof
When to Specify The Euroroof Mono single layer warm roof solution offers all of the benefits of high performance bituminous membranes, combined with quick and safe, flame-free methods of installation. Widely specified on new-build projects due to the time and cost efficiencies it offers, Euroroof Mono also suits roof refurbishment - whether to simply re-establish the integrity of the waterproofing, or to upgrade the thermal performance and/or improve roof drainage.
Warranties Alumasc offers a comprehensive range of warranty options. The typical warranty period for Euroroof Mono is 15 years. Installed exclusively by Euroroof Approved Contractors and underpinned by Alumasc’s extensive project support service, Alumasc warranties cover both product and installation. Independent insurance backed latent product defect warranties are also available through FCA licensed brokers.
Key FeaturesLifespanThe Euroroof Mono membrane has a typical life expectancy in excess of 25 years (under normal UK climatic conditions) and has been rigorously tested against wind uplift in accordance with BS 6399-2:1997.
DurabilityWith high tensile strength and pliability, Euroroof Mono membranes are designed to perform in the harshest conditions, with excellent resistance to puncture and UV degradation. The SBS elastomeric bitumen coating ensures low temperature flexibility.
PerformanceEuroroof Mono membranes have been specifically developed to provide all of the benefits typically associated with high performance bituminous membranes, without the need to use hot bitumen in the installation process.
Cost-effectiveThe quick, clean and safe installation methods of the Euroroof Mono single layer system provide excellent time and cost efficiencies during construction, whilst equally allowing the building to be operational at the earliest opportunity.
QualityEuroroof Mono membranes are manufactured and independently assessed against the BS EN ISO 9001:2008 Quality Management Standard, ensuring the highest possible consistency of product performance.
EnvironmentManufactured in accordance with the ISO 14001:2004 Environmental Management Standard, Euroroof Mono membranes score highly in BREEAM ratings (notably in Section MAT5 for the responsible sourcing of materials). Euroroof membranes can also contribute to a very good generic rating in the BRE’s Green Guide to Specification, capable of an ‘A+’ rating when installed on timber or metal decks.
Euroroof Mono Cap Sheet
Euroroof PU Membrane Adhesive
Alumasc GTF PIR Insulation adhered in Euroroof PU Insulation Adhesive
Euroroof Self-Adhesive Vapour Barrier Plus
Euroroof Contact Adhesive
Plywood Deck
ALUMASC EXTERIOR BUILDING PRODUCTS LTD
Tel: +44 (0)1744 648400 Email: [email protected]
Website: www.alumascwaterproofing.co.uk Ref: SD010FR Issued: 01/06/12 Page 2 of 2
Euroroof MonoSingle Layer Cold-Applied Bituminous Warm Roof
Application1. Tape joints and prime the plywood deck with Euroroof Contact Adhesive
immediately prior to installing the vapour barrier.
2. Roll out and align one layer of Euroroof Self-Adhesive Vapour Barrier Plus, providing for 75mm side and 100mm end laps. Remove the release film and firmly pressure roll the surface and laps to ensure adhesion.
3. Install Alumasc GTF polyisocyanurate insulation, bonded in the single component Euroroof PU Insulation Adhesive. Coverage rates are dependent upon the project’s design loads. Please refer to project specification and site test results for project-specific coverage rates. The curing time for the adhesive will be approximately 60 minutes at 10ºC, 30 minutes at 20ºC and 15 minutes at 30ºC.
4. Bed the Euroroof Mono high performance membrane in the single component Euroroof PU Membrane Adhesive to ensure a satisfactory bond with the underlying insulation. Please refer to the project specification for project-specific application rates. Seal 100mm side laps and 150mm end laps using a shoe-burner gas torch. Pressure roll the overlaps by using a 15kg roller. A small (approx 5-10mm) continuous bead of compound must always be visible at the joint.
5. Note: Pre-cut the lower corner of the end of each roll at 45º where it will be overlapped by the end lap of the next roll.
6. Install vapour control layer, insulation and underlay to upstands (where appropriate) as described in the project specification.
7. At upstands, ensure that the waterproofing extends at least 150mm above the finished roof surface and laps onto the adjoining roof membrane by at least 100mm. The head of the detail must be terminated with a suitable mechanical termination.
NB: Euroroof Mono waterproofing is exclusively installed by a nationwide network of Euroroof Approved Contractors.
The company pursues a policy of constant product development and information contained in this publication is therefore subject to change without notice. The customer is responsible for ensuring that each product is fit for its intended purpose and that the conditions for use are suitable. All quoted data is nominal and subject to production tolerances.
System Componentsn Euroroof Mono is a 4.2mm thick, polyester-
reinforced SBS-modified bitumen membrane (1 x 8 m) that is intended for use as a single layer, flame-free roof waterproofing system. The integral polyester reinforcement ensures excellent mechanical strength and dimensional resistance.
n Alumasc GTF is a CFC- and HCFC-free PIR thermal insulation with plain glass-fibre tissue to both faces and is supplied in 600 by 1200mm boards and a range of thicknesses to suit the required thermal value.
n Euroroof Self-Adhesive Vapour Barrier Plus is a high performance vapour barrier, manufactured from 2.5mm thick modified bitumen and containing an integral glass-fibre reinforcement. On the underside, a polyethylene release film covers the self-adhesive coating that will provide a strong bond with the substrate.
Technical SupportAlumasc Technical Services provide an extensive project support service that includes site surveys, project specifications, performance calculations (e.g. U-values, condensation risk analysis), CAD detail drawings and general technical advice.
Contact Alumasc Technical Services via:
+44 (0) 1744 648400
Online resources are available on our website or via the embedded links below:
Web Links
Brochures & Datasheets
NBS Specifications
CAD Drawings for typical details
www.alumascwaterproofing.co.uk
