Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
Your FlexiPot 9 System set-up guidelines
plantsAllow your
to establish
before turning your
system on.
9
[email protected] I www.autopot.co.uk I +44 (0)1276 534894 [email protected] I www.autopot.co.uk I +44 (0)1276 534894
Simple careguidelines
Ensuring that the AQUAvalve5 floods and drains correctly
Care and maintenance
Making sure your AQUAvalve5 floods and drains correctly is simply achieved and only takes a few seconds.
Hold the AQUAvalve5 at eye level so that you can see the silicone fitted to the top float resting on the hole below it.
The silicone must create a tight seal when touching the hole.
If it looks like it is not sitting parallel on the hole below, simply lift the top float and apply pressure to one side of the silicone, drop the float and hold at eye level again. Repeat the procedure if necessary.
At the end of your growing season, clean the AQUAvalve5 using warm soapy water. Using an old tooth brush will help.
The AQUAvalve5 is easily disassembled. The top float will slide all the way across and the bottom float is unclipped from its pivoting position. The circular discs fitted to the top float can also be removed by using pliers to grip the raised point.
At this point is it advisable to remove the silicones to avoid them being lost.
It is also handy to have a paper clip or pipe cleaner to hand so that you can push it through the AQUAvalve5 nozzle, this will remove any lime scale build up that may have occurred during the growing season.
Blowing through the AQUAvalve5 nozzle will also help to remove any build up. Do not under any circumstances use a drill & drill bit to clear the AQUAvalve5 nozzle.
This will potentially damage the AQUAvalve5 beyond repair.
11
2
2
3
4
Ensure the silicone is sitting parallel on the hole below it. Hold at eye level
to check the position is correct
FlexiPot 9 Systemsetup instructions
Using your front instruction sheet, repeat the module set up instructions for the number of trays.
If you require any guidance email - [email protected]
Allow your plants to establish for 7-10 days before turning system on
Plan views and options
Suggested layouts
• 1x100LFlexiTank• 9x1PotXLtrayandlid• 9x20LfabricFlexiPot• 9xAQUAvalve5• 1x16mmtankadapterandfilter• 2x16mmin-linetap
• 3x16-9mmcrossconnector• 3x16-9mmteeconnector• 1x16mmteeconnector• 6metresof16mmpipe• 4.5metresof9mmpipe• 9xFlexiPotPotSock
FlexiPot 9 System contents FlexiPot 9 dimensions
Advice
• PleasenotethatmultipleFlexiPotsmayincreaseroomhummidityduetotheexposedsurfacesofthefabricpots.
• Potupyourplants,waterthrough,thenallowyourplantstoestablishinthepotsforaperiodof7to10daysbeforeturning your system on. This will encourage a stronger and healthier root system.
• Alwaysraiseyourreservoirtoaminimumof150mmabovethehighestAQUAvalveandre-fillthereservoirwhenthereisapproximatelya1/3ofthesolutionleft-NEVERALLOWTHERESERVOIRTORUNEMPTY.
• WithAQUAvalve5systemsmineralororganicfertilisersmaybefedviathereservoirandpipework.Organicfertilisers willrequireawaterpumpinthereservoirrunningfor15minsevery2hrsandcleaningofthereservoir,pump,and filter each time the reservoir empties. Flush pipework with plain water every time the reservoir empties.
• CleanallsubstratefromthebottomandsidesofthepotsbeforeplacingintraystoensureAQUAvalvefunctionality.
• Alwaysusefreedrainingsubstrates,forexample:soil/perlite,coco/perlite,soil/claypebbles,coco/claypebbles,rockwool/clay pebbles.
8
5
Position tray so it is level.
3Remove collar.
Push 9mm pipe through collar and attach to AQUAvalve nozzle.
Rescrew collar - DON’Toverturn... when you feel it grip STOP.
Connect AQUAvalve so ‘half moon’ is on T section in the tray.
4
Cut 9mm/16mm pipe to appropriate length
6
380mm
285m
m
280mm
355m
mFlexiPot 20L
System requires minimum 100 litre FlexiTank (supplied)
9mm pipe
16mm pipe
AQUAvalve5
16mm click-fit tank adaptor & filter
16mm in-line tap
16mm – 9mm cross connector
16mm tee connector
16mm – 9mm tee connector
100 LFlexiTank
100 LFlexiTank
432mm
750m
m
7
According to the size of your system connect your 9mm/16mm pipe to relevant fitting or tank...
[email protected] I www.autopot.co.uk I +44 (0)1276 534894
Ref:9mmpipe-Outsideø9mm/Insideø7mm16mmpipe-Outsideø16mm/Insideø13mm
1 2
Fill FlexiPot with medium and pot up plants.
Fit FlexiPot PotSock over the base of FlexiPot
Secure PotSock drawstring.
Water through pot and allow to drain outside the tray. Brush off debris.
Place FlexiPot in tray.
PotSock drawstring MUST NOTbe next to AQUAvalve
Ensure NO FABRIC IS TOUCHING AQUAVALVE
Place lid over valve onto tray.