PowerPoint Presentation
DRAFTINGTHEBASIC SKIRT SLOPERObjectives: At the end of the
lesson, students should be able to:1. Identify the measurements,
tools and materials needed in drafting basic of Skirt sloper.2.
Perform in drafting Basic Skirt Sloper3. Value the importance of
Basic Skirt Sloper trade terms
Trade Terms:
Skirt = is another kind of free hanging garment extendingfrom
the waist down around the legs.
Drafting = an engineering method based on a set of body
measurement.
Sloper = a cardboard copy of the basic pattern that dart areas
and seam allowance cut away.
Apex Distance = measurement is taken across from the tip of the
left bust point to the tip of the right bust point.Hip Depth =
measurement is taken from waist-line down to the fullest part of
the hip.
skirt length = taken from the waist-line to the desired
length.Skirt width = measurement is taken from the circumference of
the hemline of the skirt.
Hips = measurement is taken from the fullest part of the
hips.waist = measurement is taken around the smallest part of the
body. measurement neededMeasurement needed:WaistSkirt lengthHip
depthSkirt widthHipsApex distance
Tools / materials needed
Tools and materials needed are:L-squareHip curvePencilManila
paperTape measure
Reminders
Reminders:Always presence of mind when drafting the patternUse
the proper tools and materials needed.Be sure to have an accurate
body measurementsClean the area after working.Return the tools and
materials in the proper place. procedure
Procedures:1. draw a perpendicular line2. Measure A to B as
skirt length3. Measure Hip Depth A to C4. Measure waist A to D add
1inch for dart measurement5. Measure A to A1, lower inch back and
inch for front.6. Measure hip measurements C to E
7.Measure skirt width B to F8. Measure A to G as apex distance
extended 4 inch line downward to J.9. Measure inch both from G,
mark H and I then connect H to J, I to J using L-square for the
dart.10. From F raised inch and mark that as K11. Connect B to K
with a slightly curve using hip curve.12. Connect D to E with the
hip curve 13. Connect E to F with a straight line using
L-square.14. Connect A1 to D as slightly curve using hip
curve.Video presentation
How to draft a pencil skirt sloper (Part 1 of
2).mp4RubricsAccuracy20%Speed25%Attitude10%Neatness of
work10%Quality of work35%Total100%Rubrics:Accuracy = the quality of
being near to the value.Speed = a rate (usually rapid) at which
something happen.Attitude = a complex mental state involving
beliefs and feeling, values and dispositions to act in certain
ways.Neatness of work = presentation was neat and orderly. Quality
of work = All procedure were followed correctly IV.
EvaluationDirection: In sheet of paper, choose the letter of the
correct answer .
1. This is an engineering method based on a set of body
measurement. A. apex distance B. drafting C. hip depth D. waist2. A
kind of free hanging garment extending from the waist down around
the legs. A. blouse B. gown C. pants D. skirt
3. Which of the following tool is needed in taking body
measurements? A. hip curve B. L-square C. ruler D. tape measure4.
The following measurements needed in drafting basic skirt sloper
except? A. apex distance B. skirt lenght C. waist D. shoulder
5. Why do we need to take a body measurement accurately in
drafting basic skirt sloper? A. for design only B. to have a good
output C. to have a guide in drafting and also the finish garment
will fit to the costumer. D. all of the above
V. AssignmentBring the following materials.1. Scissor2. Thread3.
Needle4. Pin cushion
