Embed Size (px)
Citation preview
4/15/13
Show ‘n Rise (CURVED)SERPENTINE
339016 thru 339019
CEN
TER
CO
NN
ECTI
ON
PA
NEL
EN
D P
AN
EL
EN
D P
AN
EL
CENTERPANEL
CENTERPANEL
CENTERPANEL
BACKPANEL
BACKPANEL
BACKPANEL
BACKPANEL
CENTERPANEL
Item # NAME Graphic Panels Fabric Panels CASE WRAP
339016 HARDWARE KIT-no lights NONE NONE no wrap339017 FABRIC KIT-w/light NONE (4)Center (3) End (4) Back Fabric339018 MURAL KIT/Fabric Ends-w/light (4)Center (1) End (4) Back (2) End Fabric
339019 MURAL KIT-w/light ((4)Center (3) End (4) Back NONE Graphic
12 QUAD FRAME (qty:2)
TOP VIEW
Step 1 Remove all parts from your Hard Case (3) and place on a flat, clean surface. Review the Frame (5) and notice where the pivoting light clips are located. This will determine the TOP of the display.
Step 2Pull the Frame (5) up and out from the corners until it is fully expanded on the floor. Repeat for 2nd Frame (5).
CU
RVED
EN
D P
AN
EL
CU
RVED
EN
D P
AN
EL CENTERPANEL
CENTERPANEL
CENTERPANEL
CENTERPANEL
12 Quad shown as example
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
pivoting light clip
Page 1 of 4
Step 3
Push all locking clips together to secure the Frame (5) in its expanded position.
CLOSEDOPEN
Pressure may need to be applied to
secure.
Step 4
With Frames (5) set up and in locked position, you will now be installing all of the Mag Rails (2). Steps 5 thru 9 show how to install the Mag Rails (2) as well as an instructional video:
http://creativedisplaysite.com/Mag_Rail_Install.html
Display Set-Up
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
1 - Mural Graphic Face Plates (qty: 56)**2 - Mag Rails (qty: 12)3 - Oval Hard Case (qty:2)4 - Hardware Bag (qty:2)5 - Frame (qty:2)
1
Product Parts for HARDWARE
2
6 - Double LED light kit (qty:2)7 - Panels (see chart above for qty and panel style)8 - Case to Counter Kit (qty:2)
Product Parts for PANEL KITS and LIGHTS
7
ALL PARTS COME IN THE KIT
3
GeoMetrix Graphic Face Plates
Splash Graphic Face Plates
Mural Graphic Face Plates
OUTIN
OUTIN
OUT
IN
54
6a b
c
**Frame (3) should come with Face Plates already installed.
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
8
Oval Top
wrap
8a
8b
4/15/13
OUT
IN
Step 5:
With 3-sectioned Mag Rail (2) folded, ( fold so pins are UP and facing away from the frame) start with BOTTOM section and slide back slot onto Mural Graphic Face Plates (1) on Frame.
OUT
IN
MAGNET
MAGNET
OUT
IN
OUT
IN
OUT
IN
OUT
IN
MAG
NET
MAG
NET
OUT
IN
OUT
IN
OUT
IN
slide channel over face plate
then slide over bottom face plate
OUT
IN
OUT
IN
OUT
IN
BOTT
OM
MIDDLE
TOP
Step 6:
Unfold Mag Rail (2) and fold TOP section onto MIDDLE section. (pins will now be facing the magnets on the middle section)
Slide MIDDLE section onto the next upper hub, then interlock to bottom section.
OUT
IN
OUT
IN
OUT
IN
slide channel over face plate
lock middle section to bottom section
Step 7:
OUTIN
Step 8:
Repeat to secure TOP section of Mag Rail (2) to Frame.
OUT
IN
Step 9:
Connect the Mag Rails (2) to the Frame (5) on all front connection points as well as the back vertical ends. Once all Mag Rails (2) are installed give the rails a shake to verify that are all secure.
OUT
IN
SHAKE
Step 10:
Determine which Mag Rail (2) light (6c) will attach to, and insert clip (6-b) from LED kit (6) into top of Mag Rail (2). Install LED light (6-c) from LED kit (6) onto inserted clip (6-b)
Display Set-Up Continued
6b
6b6c
Mag Rail
Page 2 of 4
BACK ENDBACK END
NOTE:
Set Frames (5) up as shown. First one needs to be concave and the second one needs to be convex.
CONCAVE CONVEX
Leave a gap. Frames are connected by a Panel (7).
4/15/13
Display Set-Up Continued...
Step 11
Set all plastic wrapped panels (7) out on floor in order of how they will be installed. All panels are installed by hooking the notch located on the top of the panel (7) to the pins at the top of the mag rail (2).
(KEEP the protective sleeves as they will be used for storage.)
Step 13
Secure the rest of the panels using the same method as in Step 8.
Note of OPTION:
Frames can be set up convex to concave HOWEVER
Step 12
Install the Panels (7) to the Frame (5). Start with the end panel. Remove it from protective sleeve, while holding it in a curved position hook the notches located on top of the panel (7) to the pins at the top of front end and back end Mag Rail (2). With top notches both hooked slide your hands down the panel securing it to the vertical Magnets.
Front end top pin Back side top pin
Step 14
Plug lights (6) into power source. Display is now ready.
CEN
TER
CO
NN
ECTI
ON
PA
NEL
EN
D P
AN
EL
EN
D P
AN
EL
CENTERPANEL
CENTERPANEL
CENTERPANEL
BACKPANEL
BACKPANEL
BACKPANEL
BACKPANEL
CENTERPANEL
CONVEXCONCAVE
*GRAPHIC PANELS WILL NEED TO BE PRINTED WITH THIS LAYOUT IN MIND*
Page 3 of 4
4/15/13
Step 3
Unplug and remove lights (6c) and clips (6b) from Frames (5). Place in carrying case.
Step 4
Remove all Mag Rails (2) from Frame (5). Collapse and place in hardware bag (4)
Step 5
Collapse Frame (5). MAKE SURE ALL LOCKING CLIPS ARE IN OPEN POSITION before collapsing Frame (5)
Step 6
Place all parts in the open center area inside the shipping cases with rolled Panels (6).
OPEN
Disassembly Instructions
Step 2
Place rolled Panels (7) into Oval Hard Cases (3).
Step 1
Remove all Panels (7) and carefully roll them up graphic/fabric side out. Place into clear protective sleeves.
GRAPHIC SIDE OUT
Step 15
Secure Wrap (8b) to the Oval Case (3). Velcro® connection point will be on the backside of Case (3).
Repeat for 2nd Case.
Step 16
Place the oval Top (8a) part of the Case to Counter Kit (8) in the groove on top of the Oval Case (3)
Repeat for 2nd Case.
Page 4 of 4
SET-UP NOTE:Display should have Face Plates (1) already installed in Frame (5). If not, Slide (with force) the Face Plate (1) into the hubs. Typically you will slide RIGHT to LEFT when looking at the face of the Frame (5).
See opposite for Face Plate Locations.FRONT VIEW (x2)
(all hubs)BACK VIEW (x2)
(vertical ends only)
GeoMetrix Graphic Face Plates
Splash Graphic Face Plates
Mural Graphic Face Plates
OUTIN
OUTIN
OUT
IN
HUB
OUT
IN
OUT
IN
OUT
IN
OUT
INOUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
INOUT
IN
OUT
IN
Warranty Information: All products are designed to provide the user with a cost-effective and durable product. Standard warranty is a ‘one year parts and labor’ warranty which warrants product against defects in material and workmanship. It does not cover damage due to accidents, abuse, or normal wear and tear. Products found to be defective will be replaced or repaired at factory’s discretion.
OUT
IN
OUT
IN
OUT
INOUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
INOUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
INOUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
INOUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
INOUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
INOUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
OUT
IN
