Ship Construction_RUDDER AND PROPELLERS

8/7/2019 Ship Construction_RUDDER AND PROPELLERS

http://slidepdf.com/reader/full/ship-constructionrudder-and-propellers 1/9

Ship Construction

Rudder and Propellers

The shape of a rudder plays an important part in its efficiency. The area of the rudder is

approximately 2% of the product of the length of the ship and the designed draught.

Since the vertical dimensions of the rudder are somewhat restricted due to the area

constraint as mentioned above, the fore and aft dimensions are increased.

Again due to this increased dimensions the torque necessary to turn this rudder is

overcome by fitting balanced or semi balanced rudders. Such a rudder has about 1/3rd of

the rudder area forward of the turning axis.



An ideal rudder is one where the centre of pressure and the turning axis coincide for all

angles of the helm.

An unbalanced rudder consists of a number of pintles and gudgeons, the top pintle being

the locking pintle which prevents any vertical movement in the rudder and the pintle And

gudgeon taking the weight of the rudder.



Principle of screw propulsion

Some people still occasionally refer to the propeller as the “airscrew”, a very accurate

and descriptive term that reflects the basic design and function of the propeller.

Leonardo da Vinci had proposed the concept of a “helical screw” to power a machine

vertically into the air.

The propeller uses that principle to provide propulsion through the air, much like a

threaded screw advances through a solid medium, with some notable exceptions,

primarily related to the loss of forward movement because the medium is not solid.

Nonetheless, the propeller is similar to a screw in some common features. First, the pitch

of a propeller is the theoretical distance the propeller would move forward in one

revolution (similar to a screw) and conceptually is the same as the pitch of a screw,

namely the distance between threads if the propeller were a continuous helix.

The second feature that relates to its screw design is that the angle of the blade changes

along the radius, so that close to the hub, the angle is very steep and at the tip of the blade

it is much more shallow.

From a practical standpoint, this means that unless the pitch for a given propeller is

known, it requires a trigonometric calculation to determine the pitch empirically.

Thirdly, just as screws come in left hand and right hand threads, propellers have the same

designation. When facing the water/ air flow if the top of the propeller moves to the

right, it is designated “Right Hand” and if to the left it is “Left Hand”. (As viewed from

the front a right hand propeller turns counterclockwise and a left hand propeller turns

clockwise.) Propellers will frequently be stamped as “RH” or “LH”.

Propeller and some definitions





Boss or Hub

The central portion of a screw propeller to which the blades are attached and through

which the driving shaft is fitted.

Rake

The point displacement, from the propeller plane to the generator line in the direction of

the shaft axis. Aft displacement is considered positive rake (see Figure 2). The rake at the

blade tip or the rake angle are generally used as measures of the rake. The strength

criteria of some classification societies use other definitions for rake.



Skew

The displacement of any blade section along the pitch helix measured from the generator

line to the reference point of the section (see Figure 2). Positive skew- back is opposite to

the direction of ahead motion of the blade section. The skew definition pertains to

midchord skew, unless specified otherwise.

Back (of blade)

The side of a propeller blade which faces generally in the direction of ahead motion. This

side of the blade is also known as the suction side of the blade because the average

pressure there is lower than the pressure on the face of the blade during normal ahead

operation.

Tip

The maximum reach of the blade from the center of the propeller hub. It separates the

leading edge from the trailing edge.

Radius

Radius of any point on a propeller.

Pitch

The pitch of a propeller is the theoretical distance the propeller would move forward in

one revolution (similar to a screw) and conceptually is the same as the pitch of a screw,

namely the distance between threads if the propeller were a screw. For this reason,

propellers will frequently be stamped with a designation such as “D 2550/P2610”. This

means that the diameter (in this case length of propeller or thickness of a screw) is 2.550

meters, and the pitch is 2.610 meters, so that in a mathematical sense, one revolution of

this propeller would move it forward a distance of 2.610 meters.



Comparing fixed-pitch with controllable-pitch propellers

Advantages of a controllable pitch propeller

Allow greater manoeuvrability

Allow engines to operate at optimum revs

Removes need for reversing engines

Reduced size of Air Start Compressors and receivers

Improves propulsion efficiency at lower loads

Disadvantages

Greater initial cost

Increased complexity and maintenance requirements

Increase stern tube loading due to increase weight of assembly, the stern tube bearing

diameter is larger to accept the larger diameter shaft required to allow room for Oil Tube

Lower propulsive efficiency at maximum continuous rating

Prop shaft must be removed outboard requiring rudder to be removed for all prop

maintenance.

Increased risk of pollution due to leak seals



Sketches the arrangement of an oil-lubricated sterntube and tailshaft

Stern tubes are fitted to provide a bearing for the tail end shaft and to enable a watertight

gland to be fitted at an accessible position.

The tube is usually constructed of cast steel with a flange at its forward end and a thread

at the after end. It is inserted from forward and this end is bolted over packing to the after

peak bulkhead. A large nut is placed over the thread at the after end, tightened and

secured to the propeller post.

In an oil lubricated stern tube the bearings are made of white metal. A gland is fitted to

each end of the stern tube and since the after end gland will not be accessible during sea

service it is made self adjusting. The flange shown is attached to the propeller so that it

rotates with the shaft and oil tightness is obtained by a rotating gland.

States how the propeller is attached to the tailshaft

The after end of the tail end shaft is tapered to receive the propeller boss and a key is

provided to transfer the torque from the shaft to the propeller. A nut fitted with a locking

plate secures the propeller in position and as an additional safeguard it is fitted with a left

hand thread in association with a right hand ed propeller or vice versa.



To remove the propeller and the tail end shaft the propeller should be slung on special

eyes provide on the shell for this purpose – the rope guards removed – and the propeller

nut slackened.

The propeller is then started from the shaft by driving steel wedges between the boss andthe propeller post. When it is free the nut is removed.

Cross-section of a shaft tunnel

Documents

Ship Construction_RUDDER AND PROPELLERS