SHINELIGHT TECHNOLOGY CO., LTDshinelight.cc/uploads/20140123152206_987.pdf · 2019. 11. 3. · SHINELIGHT TECHNOLOGY CO., LTD DIMMING FUNCTION I 0-10V ANALOG DIMMING – for SHD*-**

www.shinelight.cc Tel: 86-573-87967809 Fax: 86-573-87967851 [email protected]

SHINELIGHT TECHNOLOGY CO., LTD

120W Constant Current Output LED Driver

FEATURES

High Efficiency

Build-in Active PFC

Constant Output Current

Waterproof (IP67)

All-Round Protection: OVP, SCP, OTP

Dimming Function Optional (0-10V、PWM、Timer)

SHC120/SHD120/SHP120/ SHT120 SERIES SPECIFICATIONS

Model

Output

Current

(±5%) (mA)

Output

Voltage

(V)

Efficiency PF No Load

Output

Voltage

(±5%) (V)

Ripple &

Noise (V) 110V

Input

220V

Input

110V

Input

220V

Input

SH*120-0350SW 350 206 ~ 343 91.0% 93.0% 0.99 0.96 360 10.7

SH*120-0450SW 450 160 ~ 267 91.0% 93.0% 0.99 0.96 280 8.3

SH*120-0700SW 700 103 ~ 172 90.0% 92.0% 0.99 0.96 180 5.4

SH*120-1050SW 1050 69 ~ 114 89.0% 91.0% 0.99 0.96 120 3.6

SH*120-1400SW 1400 52 ~ 86 89.0% 91.0% 0.99 0.96 91 2.7

SH*120-1750SW 1750 42 ~ 69 88.0% 90.0% 0.99 0.96 72 2.1

SH*120-2100SW 2100 35 ~ 58 88.0% 90.0% 0.99 0.96 61 1.8

SH*120-2800SW 2800 26 ~ 43 88.0% 90.0% 0.99 0.96 45 1.4

SH*120-3150SW 3150 23 ~ 38 87.5% 89.5% 0.99 0.97 40 1.2

SH*120-4200SW 4200 18 ~ 29 87.5% 89.5% 0.99 0.97 31 0.9

NOTE: 1. All specifications are typical at 25°C unless otherwise stated.

2. The “Efficiency” & “PF” values are measured at full load, after the unit is thermally stabilized,

otherwise they will be lower about 1%.

3. The “Ripple & Noise” values are measured by 20MHz bandwidth oscilloscope and the output

paralleled a 0.1uF ceramic capacitor and a 10uF electrolytic capacitor.



ELECTRICAL SPECIFICATIONS

Parameter Values Conditions

INPUT

AC Voltage 90 ~ 305 Vac Operating Voltage

Frequency Range 47 ~ 63 Hz

AC Current (110V input) 1.25 A Full load

AC Current (220V input) 0.61 A

Inrush Current 65 A Cold start, Vin=230V

Leakage Current 0.75 mA Vin=277V, 50Hz

OUTPUT

Top Output Power 120 W

Set-up Delay Time 0.8 ~ 1.2 s

Line Regulation 1%

Load Regulation 3%

PROTECT

Over Voltage Protect

1.3 Vo ±5% floating deviation

Hiccup mode. The power supply shall return to normal

operation only after the power is turn-on again.

Short Circuit Protect

No damage shall occur when any output operating in a

short circuit condition. The power supply shall be

self-recovery when the fault condition is removed.

Over Temperature Protect 110°C

NOTE: 1. All specifications except “OTP” are measured at 25°C.

SAFETY & EMC COMPLIANCE

Parameter Standards

Safety UL/c-UL, CE UL8750, UL935, UL1012, CSA-C22.2 No.107.1

EN61347-1, EN61347-2-13

EMI EN55015

EMS

EN61000-3-2, EN61000-3-3, EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8, EN61000-4-11, EN61547

PRODUCTS INFORMATION

Parameter Values

Working Temp., Humidity -35°C ~ +70°C; 10 ~ 100% RH non-condensing

Storage Temp., Humidity -40°C ~ +85°C; 5 ~ 100% RH



MTBF 275,000 hours

Life Time 82,000 hours

Dimension (L*W*H)

SHC120-****SW-C 6.24(7.42)*3.07*1.46 inch;

158.5(188.5)*78.0*37.0 mm

SHC120-****SW-E 6.24(7.26)*3.43*1.56 inch;

158.5(184.5)*87.0*39.5 mm

Net Weight SHC120-****SW-C 900 g

SHC120-****SW-E 1000 g

APPLICATION NOTES

I DERATING CHARACTER

II POWER FACTOR CHARACTERS

III EFFICIENCY CHARACTERS

IV TOTAL HARMONICS DISTORTION

V LIFE TIME vs Tc/Ta



MECHANICAL SPECIFICATIONS

ENCAPSULATION I SHC120-****SW-C / SHT120-****SW-C

SHD120-****SW-C

SHP120-****SW-C



ENCAPSULATION II SHC120-****SW-E / SHT120-****SW-E

SHD120-****SW-E



SHP120-****SW-E



DIMMING FUNCTION

I 0-10V ANALOG DIMMING – for SHD***-**** MODELS

LED Driver V

0-10V INPUT

(purple)

0-10Vdc

GND (gray)

Mode 1：0-10Vdc Input on Dimming Control

LED Driver

0-10V INPUT

(purple)

Rx

GND (gray)

Mode 2：External Resistor on Dimming Control


Absolute Max. Voltage 0 ~ 12 V Normal 10~11V

0-10V Input Source Current 0 ~ 10 mA

NOTE: 1.If the dimming function is not used, short 10V output pin (yellow) and 0-10V input pin

(purple).

2. Io is actual output current and Ir is rated current without dimming control.

3. For the driver to operate properly, the load voltage must be maintained above the minimum

voltage threshold, proximally 50% of the max. output voltage for any given mode.

4. The dimming signal is allowed to be less than 1V, when it for 0-1V, the output current can

maintain about 10%Ir, however, the connected LEDs may flicker. Keeping dimming voltage

greater than 1V in application is strongly recommended.

5. Do not connect the GND of dimming to the output. Otherwise, the LED driver can not work

normally.

II PWM DIMMING– for SHP***-**** MODELS




Input Voltage 0~10 V Purple wire.

Input Current 10 mA

PWM Frequency 0.5 ~ 3 kHz

PWM Pulse Width 10%~100%

NOTE: 1. Pulse width less than 10% will cause the driver working unsteadily.

III TIMER DIMMING for SHT***-**** MODELS

NOTE: 1.The dimming time of the chart is for reference only, it can be adjusted according to the

client's requirement.

Documents

SHINELIGHT TECHNOLOGY CO., LTDshinelight.cc/uploads/20140123152206_987.pdf · 2019. 11. 3. · SHINELIGHT TECHNOLOGY CO., LTD DIMMING FUNCTION I 0-10V ANALOG DIMMING – for SHD***-****

SHINELIGHT TECHNOLOGY CO., LTDshinelight.cc/uploads/20140123152206_987.pdf · 2019. 11. 3. · SHINELIGHT TECHNOLOGY CO., LTD DIMMING FUNCTION I 0-10V ANALOG DIMMING – for SHD*-**