Upload
robert-roman
View
218
Download
0
Embed Size (px)
Citation preview
8/12/2019 Sharp Dust Sensor
http://slidepdf.com/reader/full/sharp-dust-sensor 1/3
GP2U06 High Sensitivity Dust Sensor
Compact and Thin Type Dust Sensor for Detecting Particles
Sharp's GP2U06 is dust sensor which integrated optical
sensor portion and signal amplifier portion.
It is suitable for indoor air purifier sensor because of
compact, thin, low dissipation current type.
(1) Compact, thin type (58 x 38 x 25mm)
(2) High sensitivity
(Dust detecting sensitivity : TYP.0.5V/(0.1mg/m3)
(3) Can detect dust even in low density area
(Minimum particle density : TYP. 0.02mg/m3)
(4) Operating voltage : 5V
(5) Low dissipation current (Icc : MAX. 15mA)
(1) Air purifiers
(2) Air conditioners
VVcc
Operating supply voltage
5±0.5
Parameter Symbol Ratings Unit
Vcc V
Input terminal voltage VLED V
Operating temperature ˚C
Storage temperature ˚C
Remarks
-
Supply voltage -0.3 to +7
-0.3 to +Vcc
-10 to +65
-20 to +80
Topr
Tstg
Terminal configuration
1
2
3
4
Output terminal
GND
Emitting device operating terminal
Vcc
58
3 8
φ9
φ3.2
Connector
12
3
4
Detecting window
2 5
(Unit : mm)Outline DimensionsGeneral Description
Features
Applications
Absolute Maximum Ratings (Ta=25˚C)
(Notice) • In the absence of device specification sheets, SHARP takes no responsibility for any defects that may occur in equipment using any SHARP deviceshown in catalogs, data books, etc. Contact SHARP in order to obtain the latest device specification sheets before using any SHARP device.
• Specifications are subject to change without notice for improvement.
(Internet) • Data for SHARP's optoelectronic/power device is provided on internet. (Address http://www.sharp.co.jp/ecg/)
Symbol Ratings Unit Remarks
-
-
-
Open drain input
8/12/2019 Sharp Dust Sensor
http://slidepdf.com/reader/full/sharp-dust-sensor 2/3
GP2U06
Conditions MIN. TYP. MAX. Unit
Detecting sensitivity K *1, 2 V/(0.1mg/m3)
Output voltage (no dust) *2 V
Range of output voltage VOH RL=4.7k Ω
LED operating current mA
Dissipation current mA
VOC
ILED
ICC
0
3.2
0.50.35 0.65
0.5
15
10
1.0
20
15
V
LED terminal=0V *2
RL= *2
Input condition to LED terminal
Recommended input conditions to LED terminal
Vcc
R1
R3
C1
R2
R4Tr
LED
+
GP2U06
2
T=30ms
T=30±5ms
PW=0.4±0.1ms
Pw=0.4ms
Detecting window
Dust
Photodiode
circuit
Emittingcircuit
Amp. Amp.Peak hold
circuit
Operation
circuit
Sensitivity adjustment
Vcc
Output terminal(Vo)
GND
3
2
1
4
Emitting device
Operating terminal
Parameter Symbol
Electro-optical Characteristics
Block Diagram
(Ta=25˚C, Vcc=5V)
High Sensitivity Dust Sensor
-
-
- -
*1 • Dust density is measured by mildseven smoke density, using digital dust meter [P-5L2 made by
SHIBATA scientific instrumental industry].
• Detecting sensitivity is settled according to the change of output voltage when dust density change
0.1mg/m3 from the initial value.
*2 Input conditions to LED terminal (pulse operation condition) is shown in the right figure.
8/12/2019 Sharp Dust Sensor
http://slidepdf.com/reader/full/sharp-dust-sensor 3/3
This datasheet has been download from:
www.datasheetcatalog.com
Datasheets for electronics components.