SGSN SG7.0 CD6 Cause Description

Nokia Siemens Networks SGSN SG7.0 CD6 Cause Description

1 (98)DN0516745 Issue 11-1

Nokia Siemens Networks


2 (98) Nokia Siemens Networks

DN0516745Issue 11-1

The information in this document is subject to change without notice and describes only the product defined in the introduction of this documentation. This documentation is intended for the use of Nokia Siemens Networks customers only for the purposes of the agreement under which the document is submitted, and no part of it may be used, reproduced, modified or transmitted in any form or means without the prior written permission of Nokia Siemens Networks. The documentation has been prepared to be used by professional and properly trained personnel, and the customer assumes full responsibility when using it. Nokia Siemens Networks welcomes customer comments as part of the process of continuous development and improvement of the documentation. The information or statements given in this documentation concerning the suitability, capacity, or performance of the mentioned hardware or software products are given as is and all liability arising in connection with such hardware or software products shall be defined conclusively and finally in a separate agreement between Nokia Siemens Networks and the customer. However, Nokia Siemens Networks has made all reasonable efforts to ensure that the instructions contained in the document are adequate and free of material errors and omissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks, explain issues which may not be covered by the document. Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NO EVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THIS DOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO SPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES, SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESS INTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THE USE OF THIS DOCUMENT OR THE INFORMATION IN IT. This documentation and the product it describes are considered protected by copyrights and other intellectual property rights according to the applicable laws. The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademark of Nokia Corporation. Siemens is a registered trademark of Siemens AG. Other product names mentioned in this document may be trademarks of their respective owners, and they are mentioned for identification purposes only. Copyright Nokia Siemens Networks 2010. All rights reserved.

Contents

Contents

1 Introduction ............................................................................................ 7

2 SGSN cause codes............................................................................... 102.1 Structure of SGSN Cause ...................................................................... 102.2 Procedure codes (sg_proc_t) ................................................................. 112.3 Initiation causes (sg_init_t) ..................................................................... 152.4 Error causes (sg_err_t) .......................................................................... 20

3 Internal cause to interface cause mapping from MM & SM processes ............................................................................................. 65

3.1 MS initiated attach (GPRS or combined) rejected by network ............... 663.2 MS initiated combined attach accepted GPRS services only

(CS-side fails) ......................................................................................... 693.3 MS initiated routing area update rejected by the network ...................... 703.4 MS initiated combined RAU accepted for GPRS services only

(CS-side fails) ......................................................................................... 733.5 MS initiated PDP context activation rejected by the network ................. 753.6 MS initiated PDP context modification rejected by the network ............. 773.7 Network requested PDP context deactivation ........................................ 783.8 MS initiated service request rejected by the network ............................. 793.9 NW initiated detach request ................................................................... 813.10 Cause mapping between Gr interface (MAP protocol/HLR/AuC

> SGSN > MS) ................................................................................... 833.10.1 Location update procedure..................................................................... 833.11 Cause mapping between GGSN > SGSN > MS ................................ 843.11.1 Create PDP context response ................................................................ 843.11.2 Update PDP context response ............................................................... 86



DN0516745Issue 11-1

Summary of changes

Summary of changes

Changes made between releases SG7.0 CD6 and SG7.0 CD2

The document has been updated to SGSN Release 7.0 CD6 level, including the title.

Section Error causes: Error cause cancel_location_cc, 0x189 has been added.

Error cause No_res_available_c, 0x0C has been updated.

Changes made between releases SG7.0 CD2 and SG7.0 The document has been updated to SGSN Release 7.0 CD2 level, including the title.

Section Error causes: Error causes 0x17F, 0x180, 0x181, 0x182, 0x183, 0x184, 0x185, 0x186, 0x187, 0x88 have been added.

Changes made between releases SG7.0 and SG6.0 CD6

The document has been updated to SGSN Release 7.0 level, including the title.

Section Error causes: Error causes 0x173, 0x178, 0x179, 0x17A, 0x17B, 0x17C, 0x17D, and 0x17E have been added.

Section MS initiated attach (GPRS or combined) rejected by network:

Error causes 0x178, 0x179, 0x17A, 0x17B, 0x17C, and 0x17D have been added. The notes related to cause value #11 have been updated due to the error cause 0x17D.

Section MS initiated PDP context activation rejected by the network:

Error cause 0x173 has been added.

Section Cause mapping between GGSN -> SGSN -> MS, Chapter Create PDP context response:

Cause APN access denied, 222, has been updated.



DN0516745Issue 11-1

Changes made between releases SG6.0 CD6 and SG6.0 CD4

The document has been updated to CD6 level, including the title.

Section Procedure codes:

Procedure codes 0x3E, 0x3F, 0x40, 0x90, and 0x91 have been added.

Section Initiation causes:

Initiation cause 0xB6 has been added.

Section Error causes: Error cause 0x177 has been added.

Error causes 0x11, 0x2C, 0x2D, 0x38, and 0x3F have been modified.

Summary of changes

1 Introduction SGSN Cause has been developed to map the error causes coming from any interface to SGSN causes. The numeric values defined in the corresponding interface specifications are changed to human readable literals, and the mapping is done in one place only. This means that if some numeric value is changed in the specification, it only needs to be changed in SGSN cause mapping, not in the source code(s).

SGSN Cause also contains internal causes, which are used by processes internally and when exchanging information with another process, but which may be used to find more information on the error that occurred.

External cause code (reject cause sent to the Mobile Station (MS), based on specification) and SGSN Cause are shown in Traffica reports.

SGSN Cause is also used in Call Detail Records (CDRs) in SGSN Charging. SGSN Cause is used in the diagnostics field in CDRs (see 3GPP TS 32.215 Charging data description for the Packet (PS) domain). Diagnostics give a more detailed reason for the release of the connection. Basically, when the CDR has closed the same event, the cause for the CDR closing can be seen in the Traffica report. Both the event shown in Traffica and the closed CDR's diagnostics have the same SGSN Cause value.



DN0516745Issue 11-1

Note Nokia Siemens Networks reserves the right to modify internal causes during the lifecycle of the software package. The meaning of internal causes and their triggers can change within and between the different software packages. The newest version of the document describing the internal and external causes should be always used.

Before using any information in this document, please check if there is a newer version available.

Summary of changes



DN0516745Issue 11-1

2 SGSN cause codes 2.1 Structure of SGSN Cause

The SGSN Cause is divided into five different cause parts. The parts are:

SG_PROC_T This part indicates the ongoing procedure of GMM or SM operation.

SG_INIT_T This part indicates who has started the operation (network or MS) or the reason why a specific operation has been started.

FAMILY_ID_T This part contains the family identifier, and it shows the family that has been set by the actual error cause.

SG_ERR_T This part contains the actual error cause. The error cause listing contains the cause literal, interface cause value in hexadecimal number and the verbal explanation.

INT_CAUSE (WORD) This part is reserved for internal use by process families. It can be used to give more detailed information on error situations to designers.

Summary of changes

2.2

Procedure codes (sg_proc_t)

undefined_c 0xFF Initialisation value

attach_c 0x0 Attach, unspecified

gprs_attach_c 0x1 GPRS attach

comb_attach_c 0x2 Combined GPRS/IMSI attach

imsi_attach_c 0x3 IMSI attach

og_inter_sgsn_att_c 0x5 Outgoing inter SGSN attach

og_inter_papu_att_c 0x6 Outgoing inter PAPU attach

ra_update_c 0x10 RA update, type unspecified

intra_papu_ra_upd_c 0x11 Intra PAPU RA update

inter_papu_ra_upd_c 0x12 Inter PAPU RA update

inter_sgsn_ra_upd_c 0x13 Inter SGSN RA update

inter_sg_ra_w_imsi_c 0x14 Inter SGSN RA update with IMSI attach

intra_papu_ra_imsi_c 0x15 Intra PAPU RA update with IMSI attach

inter_papu_ra_imsi_c 0x16 Inter PAPU RA update with IMSI attach

intra_papu_comb_upd_c 0x17 Intra PAPU combined RA/LA update

inter_papu_comb_upd_c 0x18 Inter PAPU combined RA/A update

inter_sgsn_comb_upd_c 0x19 Inter SGSN combined RA/LA update

periodic_comb_upd_c 0x1A Periodic combined RA/LA update

periodic_ra_upd_c 0x1B Periodic RA update

og_inter_papu_rau_c 0x1C Outgoing inter PAPU RA update

og_inter_sgsn_rau_c 0x1D Outgoing inter SGSN RA update



DN0516745Issue 11-1

og_inter_sys_rau_c 0x1E Outgoing inter SGSN RA update from 2G system to 3G

detach_c 0x20 Detach, type unspecified

pwr_off_detach_c 0x21 Power off detach

mo_gprs_detach_c 0x22 MS-originated GPRS detach

mo_comb_detach_c 0x23 MS-originated GPRS/IMSI detach

mo_imsi_detach_c 0x24 MS-originated IMSI detach

nwr_gprs_detach_c 0x25 Network-requested GPRS detach

nwr_comb_detach_c 0x26 Network-requested GPRS/IMSI detach

nwr_imsi_detach_c 0x27 Network-requested IMSI detach

impl_gprs_detach_c 0x28 Implicit GPRS detach

impl_comb_detach_c 0x29 Implicit GPRS/IMSI detach

purge_c 0x2A Purge

authentication_c 0x30 Authentication

ptmsi_realloc_c 0x31 PTMSI reallocation

imei_chk_c 0x32 IMEI check

identity_enq_c 0x33 MS information enquiry

cs_call_c 0x34 CS call

gmm_rel_c 0x35 GMM connection release

detach_by_timer_c 0x36 Detach timer expired

lic_activation_c 0x37 Lawful interception

resume_c 0x38 Resume

og_cs_call_c 0x39 CS call indication to old location

Summary of changes

inter_p_i_ra_up_rel_c 0x3A Inter PAPU RAU after relocation with IMSI

inter_s_i_ra_up_rel_c 0x3B Inter SGSN RAU after relocation with IMSI

inter_p_c_ra_up_rel_c 0x3C Inter PAPU combined RAU after relocation

inter_s_c_ra_up_rel_c 0x3D Inter SGSN combined RAU after relocation

intra_p_i_ra_up_rel_c 0x3E Intra PAPU RAU after relocation with imsi

intra_p_c_ra_up_rel_c 0x3F Intra PAPU combined RAU after relocation

intra_p_ra_upd_relo_c 0x40 Intra PAPU RAU after relocation

mo_activation_c 0x60 MS-requested PDP context activation

nwr_activation_c 0x61 Network-requested PDP context activation

mo_deactivation_c 0x62 MS-requested PDP context deactivation

nwr_deactivation_c 0x63 Network-requested PDP context deactivation

modify_service_c 0x64 Mobile- or network-originated PDP context modification

Context activation to another PAPU/SGSN

param_chg_service_c 0x65 HLR-initiated PDP context modification

deact_service_c 0x66 GMC-requested PDP context deactivation

implicit_deact_c 0x67 PDP context deactivation due to network status

mt_lr_c 0x90 mobile terminated location request

eme_mt_lr_c 0x91 emergency mobile terminated location request

mo_sms_c 0xA0 Mobile-originated SMS procedure

mt_sms_c 0xA1 Mobile-terminated SMS procedure

pfc_download_c 0xB1 BSS-initiated PFC download procedure

pdp_context_inact_c 0xB2 PDP context moves to inactive state

pdp_context_active_c 0xB3 PDP context moves to active state



DN0516745Issue 11-1

lic_deactivation_c 0xC0 Lawful interception deactivation

lic_request_c 0xC1 Lawful interception request

ssf_activity_test_c 0xC2 The SCP sends 'alive' query to the SGSN

ssf_continue_c 0xC3 The SCP instructs the SGSN to continue processing

bss_trace_act_c 0xC4 Activation of BSS TRACE

bss_trace_deact_c 0xC5 Deactivation of BSS TRACE

alert_req_c 0xC6 Alert procedure

og_inter_pa_3t2_sho_c 0xC7 Outgoing inter PAPU RA update from 3G system to 2G

og_inter_pa_2t3_sho_c 0xC8 Outgoing inter PAPU RA update from 2G system to 3G

intra_papu_relo_c 0xD0 Intra PAPU relocation

inter_papu_relo_c 0xD1 Inter PAPU relocation

inter_sgsn_relo_c 0xD2 Inter SGSN relocation

og_inter_papu_relo_c 0xD3 Outgoing inter PAPU relocation

og_inter_sgsn_relo_c 0xD4 Outgoing inter SGSN relocation

inter_p_ra_upd_relo_c 0xD5 Inter PAPU RAU after relocation

inter_s_ra_upd_relo_c 0xD6 Inter SGSN RAU after relocation

og_inter_s_rau_relo_c 0xD7 Outgoing inter SGSN RAU after relocation

og_inter_p_rau_relo_c 0xD8 Outgoing inter PAPU RAU after relocation

intra_p_rau_relo_c 0xD9 Intra PAPU RAU after relocation

service_request_c 0xE0 Service request

iu_reset_c 0xE1 Releasing one or more Iu connection, for example in RNC reset

iu_release_c 0xE2 Releasing one Iu connection

Summary of changes

iu_sign_conn_rel_c 0xE3 Releasing one Iu connection

intra_papu_2t3_sho_c 0xE4 Intra PAPU inter system RAU from 2G system to 3G

intra_p_2t3_imsi_c 0xE5 Intra PAPU inter system RAU from 2G system to 3G with IMSI attach

intra_p_2t3_comb_c 0xE6 Combined intra PAPU inter system RAU from 2G system to 3G

intra_papu_3t2_sho_c 0xE7 Intra PAPU inter system RAU from 3G system to 2G

intra_p_3t2_imsi_c 0xE8 Intra PAPU inter system RAU from 3G system to 2G with IMSI attach

intra_p_3t2_comb_c 0xE9 Combined intra PAPU inter system RAU from 3G system to 2G

inter_papu_2t3_sho_c 0xEA Inter PAPU inter system RAU from 2G system to 3G

inter_p_2t3_imsi_c 0xEB Inter PAPU inter system RAU from 2G system to 3G with IMSI attach

inter_p_2t3_comb_c 0xEC Combined inter PAPU inter system RAU from 2G system to 3G

inter_papu_3t2_sho_c 0xED Inter PAPU inter system RAU from 3G system to 2G

inter_p_3t2_imsi_c 0xEE Inter PAPU inter system RAU from 3G system to 2G with IMSI attach

inter_p_3t2_comb_c 0xEF Combined intra PAPU inter system RAU from 3G system to 2G

rab_create_c 0xF0 RAB create

gmm_info_c 0xF1 GMM information

2.3 Initiation causes (sg_init_t)

undefined_c 0xFF Initialisation value; undefined

ms_initiated_c 0x0 MS-initiated

nw_initiated_c 0x1 Network-initiated

rej_ra_upd_c 0x2 Rejected inter PAPU/SGSN routing area update

rej_attach_c 0x3 Rejected GPRS attach



DN0516745Issue 11-1

rej_auth_c 0x4 Failed authentication

ra_upd_c 0x5 For security procedures

attach_c 0x6 Reattach from MS

Reattach from MS, while MS was already attached, implicit detach for old mm-context will be initiated before new attach can be processed

sm_proc_c 0x7 For security procedures

gsms_proc_c 0x8 For security procedures

mmi_c 0x9 For security procedures

reatt_req_c 0xC The MS is requested to perform a GPRS detach and a new attach

scp_initiated_c 0xD SCP-initiated procedure

hlr_initiated_c 0x20 HLR-initiated procedure

qos_not_accepted_c 0x21 The MS starts deactivation during MO activation

ggsn_recovery_c 0x22 GGSN has been reset, the SM deactivates context

no_sgsn_resources_c 0x23 SGSN has no resources to finish the requested operation

remote_release_c 0x24 Data link has been released by the MS

detach_c 0x25 GPRS detach

mnr_c 0x26 The MS is unreachable

inter_sgsn_rau_c 0x27 Inter SGSN routing area update

inter_papu_rau_c 0x28 Inter PAPU routing area update

og_inter_sgsn_rau_c 0x29 Inter SGSN routing area update to new SGSN

og_inter_papu_rau_c 0x2A Inter PAPU routing area update to new PAPU

failed_imei_chk_c 0x2B IMEI check failed

ll_fail_c 0x2C Lower layer failure

Summary of changes

cs_call_c 0x2D Circuit switched call

no_resources_c 0x2E The MS requests context deactivation due to the lack of resources

unsupp_llc_sapi_c 0x2F The MS does not accept SAPI in MO PDP context activation

u_context_in_ggsn_c 0x30 GGSN has no context to send the MS's data packet

llc_fail_c 0x31 GIPPRB out of order

gsp_exp_c 0x32 GSPPRB's timer expiry

ms_reachab_exp_c 0x33 MS reachable timer expiry

gip_mas_ann_c 0x34 GIPPRB's master detected that GIPPRB's slave is out of order

og_attach_c 0x35 Outgoing attach (attach in new SGSN)

smmu_reset_c 0x36 Leads to detach and activation rejection

time_quota_c 0x37 Frozen hand process leads to release

llc_sndcp_error_c 0x38 Error occurred in SNDCP/LLC layer

ggsn_initiated_c 0x39 Indicates that a GGSN-initiated PDP Context Modification is started

ptmsi_realloc_c 0x50 PTMSI reallocation procedure

identity_enq_c 0x51 Identity enquiry procedure

auth_c 0x52 Authentication procedure

int_sgsn_rau_det_c 0x60 Inter PAPU and inter SGSN situations: PDP-detach request is received in RAU

intra_p_rau_det_c 0x61 Intra PAPU situation: pdp-detach request is received in RAU

int_sgsn_uns_det_c 0x62 Used in inter SGSN RAU situations when both CRs are full

pwr_off_detach_c 0x63 The MS has made a power off detach

mo_activation_c 0x64 The MS has tried to activate the same context twice

og_inter_papu_att_c 0x65 Inter PAPU attach

og_inter_sgsn_att_c 0x66 Inter SGSN attach



DN0516745Issue 11-1

intra_papu_rau_c 0x67 Intra PAPU routing area update

g_att_clo_exp_c 0x68 Inter SGSN attach; the cancel location timer has expired

g_rau_clo_exp_c 0x69 Inter SGSN RAU; the cancel location timer has expired

e_est_c 0x6A Ack context re-establishment

o_pdp_in_gtp_c 0x6B Unknown PDP context in GTP

o_pdp_in_ggsn_c 0x6C Unknown PDP context in GGSN

lr_detach_c 0x6D HLR initiated detach; necessary for PDP context

bss_initiated_c 0x70 BSS PFC download/modify procedures

og_inter_sys_rau_c 0x71 Outgoing inter system RA update

cell_change_c 0x72 PDP context modification initiated by cell change

og_inter_p_3t2_sho_c 0x80 Outgoing inter system inter PAPU RAU from 3G system to 2G

og_inter_p_2t3_sho_c 0x81 Outgoing inter system inter PAPU RAU from 2G system to 3G

og_inter_s_3t2_sho_c 0x82 Outgoing inter system inter SGSN RAU from 3G system to 2G

og_inter_s_2t3_sho_c 0x83 Outgoing inter system inter SGSN RAU from 2G system to 3G

intra_p_3t2_sho_c 0x84 Intra PAPU inter system RAU from 3G system to 2G

intra_p_2t3_sho_c 0x85 Intra PAPU inter system RAU from 2G system to 3G

inter_p_3t2_sho_c 0x86 Inter PAPU inter system RAU from 3G system to 2G

inter_p_2t3_sho_c 0x87 Inter PAPU inter system RAU from 2G system to 3G

inter_s_3t2_sho_c 0x88 Inter SGSN inter system RAU from 3G system to 2G

inter_s_2t3_sho_c 0x89 Inter SGSN inter system RAU from 2G system to 3G

rnc_initiated_c 0x90 RNC initiated procedure

rab_release_c 0x91 RAB release initiated context modify procedure

Summary of changes

paging_c 0x92 SGSN initiated paging procedure

rab_setup_c 0x93 RAB setup in RAU procedure

service_request_c 0x94 Service request initiated procedure

gtp_initiated_c 0x95 GTP initiated RAB release

intra_papu_rel_c 0xA0 Intra PAPU relocation

inter_papu_rel_c 0xA1 Inter PAPU relocation

inter_sgsn_rel_c 0xA2 Inter SGSN relocation

og_inter_papu_rel_c 0xA3 Outgoing inter PAPU relocation

og_inter_sgsn_rel_c 0xA4 Outgoing inter SGSN relocation

no_rau_after_rel_c 0xA5 No RAU after relocation

clo_after_rel_c 0xA6 Cancel location after relocation, RAU to different unit

atm_ip_change_c 0xA7 IP address changed because of ATM connection

mas_rel_for_rab_c 0xA8 Mass release for RABs from GTP

ot_to_2t_lic_c 0xB0 One tunnel changed to two tunnel because of LIC

ot_to_2t_camel_c 0xB1 One tunnel changed to two tunnel because of CAMEL

papu_bl_mass_det_c 0xB2 Mass detach due to PAPU blocking

multi_off_mass_det_c 0xB3 Mass detach due to Multipoint Offload

gmlc_initiated_c 0xB6 GMLC-initiated location request



DN0516745Issue 11-1

2.4 Error causes (sg_err_t)

Internal cause (sg_err_t)

Internal cause value

Internal cause explanation Cause set by family

Undefined_c 0xFFFFFFFF

Any family: Initialise value. Any family

success_c 0x00 Any family: Successful procedure. Any family

send_full_c 0x01 GTPPRB: Cause code returned by Charging Gateway (see ETSI TS 12.15).

GTPPRB

receive_full_c 0x02 GTPPRB: Cause code returned by Charging Gateway (see ETSI TS 12.15).

GTPPRB

another_down_c 0x03 GTPPRB: Cause code returned by Charging Gateway (see ETSI TS 12.15).

GTPPRB

this_down_c 0x04 GTPPRB: Cause code returned by Charging Gateway (see ETSI TS 12.15).

GTPPRB

req_acc_c 0x05 GTPPRB: GTPPRB notifies the GGSN about a successful operation.

GTPPRB

Nonexistent_c 0x06 GTPPRB: GTPPRB tells the GGSN to delete the operation which failed due to a nonexistent context.

GTPPRB

inv_msg_frm_c 0x07 GTPPRB: GTPPRB received a message with invalid format.

GTPPRB

imsi_not_known_c 0x08 GTPPRB: GTPPRB tells that the old SGSN IMSI cannot be found.

GTPPRB

Summary of changes

GCSPRB: GCSPRB has noted that the IMSI has changed during the MM/SM procedure. The ongoing procedure is rejected.

GIPPRB: Location information was requested with an invalid IMSI.

GCSPRB

GIPPRB

Ms_gprs_detached_c 0x09 GTPPRB: GTPPRB informs the old SGSN about a collision of attach or detach.

GS1PRB: MS GPRS detached.

GTPPRB

GS1PRB

Ms_not_gprs_rsp_c 0x0A GTPPRB: GTPPRB informs the old SGSN that the MS is lost or it is not of GPRS quality.

GTPPRB

version_not_supp_c 0x0B GTPPRB: Cause code returned by Charging Gateway (see ETSI TS 12.15).

GTPPRB

No_res_available_c 0x0C GTPPRB, GUDPRB: GTPPRB's TID table or sequence number table (for RAUs) has run out of room.

The GTP had resources for 500 simultaneous inter-unit RAUs before Change Notes SG2_0326, SG3_0152 and SG31_0199; after these, there are resources for 5000 simultaneous inter-unit RAUs.

This cause is also set when TEID table or PDP table becomes full.

GTPPRB: Cause code (199) returned by the GGSN (see 3GPP TS 29.060).

GMGPRB: PRFILE is active with PDP_REJ_IF_RAB_FAILS parameter. Therefore, every RAB failure causes PDP context rejection with this cause.

GTPPRB

GUDPRB

serv_not_supp_c 0x0D GTPPRB: MS97/98 is trying to create secondary context.

GTPPRB



DN0516745Issue 11-1

GS1PRB: Service not supported by the mobile station.

GS1PRB

mand_ie_inc_c 0x0E GTPPRB: GTPPRB tells that the GGSN could not decode a mandatory IE.

GTPPRB

mand_ie_missing_c 0x0F GTPPRB: GTPPRB tells that the GGSN could not find a mandatory IE.

GTPPRB

opt_ie_inc_c 0x10 GTPPRB: GTPPRB tells that the GGSN could not decode an optional IE.

GTPPRB

system_failure_c 0x11 GTPPRB: GTPPRB sets this when there is no appropriate error cause. This cause can also come directly from the GGSN (see 3GPP TS 29.060).

GLRPRB: GSBASE reading error during location request.

GTPPRB

GLRPRB

roam_restr_c 0x12 GTPPRB: GTPPRB informs the old SGSN that the MS is not allowed to roam.

GTPPRB

ptmsi_sign_mism_c 0x13 GTPPRB: GTPPRB informs the old SGSN about a PTMSI signature mismatch.

GMGPRB: The PTMSI signature received from the MS does not match the current one; routing area needs to be updated otherwise the attach is rejected.

GTPPRB

GMGPRB

auth_failure_c 0x14 GTPPRB: Cause code (208) returned by the GGSN (see 3GPP TS 29.060).

GMGPRB: (Case 1): Subscriber authentication fails.

GMGPRB: (Case 2): Error in receiving authentication vectors (authentication vector type not

GTPPRB

GMGPRB

Summary of changes

defined).

GSPPRB: authentication is considered as failed, and the GSPPRB's GMM/SM hand uses this internal cause to inform the GSPPRB's GSMS hand to abort the SMS procedure.

GS1PRB: User authentication fails when Authentication check is requested.

GSPPRB

GS1PRB

usr_auth_fail_c 0x15 GTPPRB: Cause code (209) returned by the GGSN (see 3GPP TS 29.060). Subscriber authentication fails; the ongoing procedure is interrupted.

GMGPRB (Case 1): Subscriber authentication fails because of the received A&C reference number.

GMGPRB (Case 2): Subscriber from Iu access is trying to attach but the authentication is OFF.

GTPPRB

GMGPRB

ctxt_not_found_c 0x16 GTPPRB: Cause code returned by the GGSN (see 3GPP TS 29.060).

GUDPRB: Unknown subscriber.

GTPPRB

GUDPRB

dyn_ips_occupied_c 0x17 GTPPRB: Cause code returned by the GGSN (see 3GPP TS 29.060).

The GGSN does not have any more room for dynamic PDP-addresses when the SGSN (or the MS) has requested a dynamic PDP-address.

GTPPRB

No_mem_available_c 0x18 GTPPRB: Cause code returned by the GGSN (see 3GPP TS 29.060).

The GGSN does not have enough memory to perform the tasks the SGSN (or actually the MS) has requested it to perform.

GTPPRB

unkn_mand_ext_hd_c 0x19 GTPPRB: Cause code returned by the GGSN (see 3GPP TS 29.060).

GTPPRB



DN0516745Issue 11-1

sem_err_in_tft_c 0x1A GTPPRB: Cause code returned by the GGSN (see 3GPP TS 29.060).

GTPPRB

syn_err_in_tft_c 0x1B GTPPRB: Cause code returned by the GGSN (see 3GPP TS 29.060).

GTPPRB

sem_err_in_pfi_c 0x1C GTPPRB: Cause code returned by the GGSN (see 3GPP TS 29.060).

GTPPRB

syn_err_in_pfi_c 0x1D GTPPRB: Cause code returned by the GGSN (see 3GPP TS 29.060).

GTPPRB

unknown_apn_c 0x1E GMGPRB: Failed to select APN for PDP context during PDP context activation. PDP context activation is rejected.

GMGPRB

req_rel_poss_dupl_c 0x1F GTPPRB: Cause code returned by charging gateway (see ETSI TS 12.15).

GTPPRB

synch_failure_c 0x20 GSPPRB: This cause is sent to the network by the ME if the SIM detects that the SQN (Sequence Number) in the authentication request message is 'out of range' (see 3GPP TS 33.102, 24.008).

GSPPRB

mac_failure_c 0x21 GSPPRB: This cause is sent to the network by the ME if the SIM detects that the MAC (Message Authentication Code) in the authentication request message is not fresh (see 3GPP TS 33.102, 24.008).

GSPPRB

incorrect_msg_c 0x22 GCSPRB: GCSPRB has received a message from a wrong GMGPRB hand. The ongoing procedure is interrupted.

GCSPRB

Summary of changes

inv_mand_inf_c 0x23 GSPPRB: The network sets this cause to indicate that it has received a message with a non-semantic mandatory IE error (see 3GPP TS 24.008).

GMGPRB: Network sets this cause to indicate that it has received an invalid QoS profile request in context activation from 3G radio access. (24.008 v3.11.0 (R99), 24.008 v7.7.0 (R7))

GSPPRB

GMGPRB

cond_ie_err_c 0x26 GRNPRB: The VLR returned a location update reject message with reject cause #100.

GRNPRB

inv_rai_info_c 0x28 GMGPRB: Abnormal RAI values. The MS sends incorrect RAI information in the routing area update request message to the SGSN, or GMGPRB receives incorrect RAI information during a CS-call. The routing area update is rejected to the new PAPU/SGSN.

GMGPRB

imsi_u_in_hlr_c 0x29 GRNPRB: The MAP protocol returned MAP error 'IMSI unknown' in the HLR or the VLR returned a location update reject message with reject cause #2.

GRNPRB

imsi_u_in_auc_c 0x2A GRNPRB: The MAP protocol returned a MAP error 'IMSI unknown' in the AuC.

GRNPRB

map_system_fail_c 0x2B GRNPRB: The MAP protocol returned a MAP error 'System failure'.

GRNPRB

data_missing_c 0x2C GRNPRB: the MAP protocol returned a MAP error 'Data missing' or some mandatory data is missing from the received MAP message.

GCSPRB: Data is missing in the received message from GMGPRB, because, for example, there is no IMSI in the message received from GMGPRB.

The ongoing process is rejected.

GRNPRB

GCSPRB



DN0516745Issue 11-1

GLRPRB: No IMSI or MSISDN received in location request.

GLRPRB

unexp_data_val_c 0x2D GRNPRB: The MAP protocol returned a MAP error 'unexpected data value', the HLR returned an unexpected value in MAP message, or unexpected data was received in a MAP message.

GLRPRB: Location estimate type is not supported.

GRNPRB

GLRPRB

unknown_equip_c 0x2E GRNPRB: The MAP protocol returned a MAP error 'unknown equipment'.

GRNPRB

unexp_cause_val_c 0x2F GRNPRB: The MAP protocol returned an unexpected MAP error value or the VLR returned a location update reject with an unexpected reject cause.

GRNPRB

No_gprs_subscr_c 0x30 GRNPRB: The MAP protocol returned a MAP error 'not GPRS subscriber'.

GRNPRB

Unassigned_number_c 0x31 SGIPRB: Cause code returned by SCP. SGIPRB

oper_det_barring_c 0x32 SGIPRB: Cause code returned by SCP.

GS1PRB: Operator determinated barring is activated.

SGIPRB

GS1PRB

call_barred_c 0x33 SGIPRB: Cause code returned by SCP. SGIPRB

cug_reject_c 0x34 SGIPRB: Cause code returned by SCP. SGIPRB

Sm_trans_reject_c 0x35 SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. The SCP orders the SGSN to release MO-SMS sending (specified in SSP - SCP interface).

SGIPRB

Summary of changes

GS1PRB: short message transfer is rejected. GS1PRB sets this error cause when the SM transfer is interrupted for some reason (for example, SMS sending is rejected by the MS, the type of subscriber number is invalid, or MAP interface returns a negative acknowledgement).

GS1PRB

mem_cap_exceeded_c 0x36 SGIPRB: Not in use at the moment (specified in the SSP - SCP interface).

SGIPRB

dest_out of_serv_c 0x37 SGIPRB: Not in use at the moment (specified in the SSP - SCP interface).

SGIPRB

unident_ms_c 0x38 GS1PRB: Unidentified mobile station. GS1PRB sets this error cause when its attempt to read MO or MT SMS subscriber information from the database failed.

GLRPRB: Subscriber is not found from GSBASE in location request.

GS1PRB

GLRPRB

facility_reject_c 0x39 GS1PRB: facility rejected. GS1PRB sets this error cause when MO or MT hand creation has failed.

SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation (specified in the SSP - SCP interface).

GS1PRB

SGIPRB

unknown_ms_c 0x3A GS1PRB: The subscriber number is not within limits.

SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the (SSP - SCP interface).

GS1PRB

SGIPRB



DN0516745Issue 11-1

GMGPRB: the MS or the network has requested an action to an unknown subscriber.

GIPPRB (Case 1): A PDP context activation, modification or release request is rejected by the GIPPRB because the TLLI in the request does not exist in the GIPPRB TLLI table.

GIPPRB (Case 2): A location information request was made for an IMSI that was not yet successfully registered in the PAPU.

GMGPRB

GIPPRB

net_outof_order_c 0x3B SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the SSP - SCP interface).

SGIPRB

temp_failure_c 0x3C SGIPRB: error in SMS handling. The cause code is sent to GMGPRB in the ssf_release_context_ind_s and ssf_release_gprs_ind_s messages.

GS1PRB: temporary failure.

SGIPRB

GS1PRB

Congestion_c 0x3D SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the SSP - SCP interface).

SGIPRB

res_navail_unspec_c 0x3E SGIPRB: Hand creation failed. The cause code is sent to GMGPRB in the ssf_release_context_ind_s and ssf_release_gprs_ind_s messages.

SGIPRB

req_fac_not_subsc_c 0x3F GS1PRB: the requested facility is not subscribed. GS1PRB sets this error cause when the MO or MT SMS teleservice code is not provisioned.

GS1PRB

Summary of changes

SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the SSP - SCP interface).

GLRPRB: Radio access type or GAD shape is not supported in location request.

SGIPRB

GLRPRB

req_fac_nimp_c 0x40 SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the SSP - SCP interface).

SGIPRB

inv_sm_trans_ref_c 0x41 SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the SSP - SCP interface).

SGIPRB

invalid_message_c 0x42 SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the SSP - SCP interface).

SGIPRB

info_elem_missing_c 0x43 SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the SSP - SCP interface).

SGIPRB

msg_not_ex_or_imp_c 0x44 SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the SSP - SCP interface).

SGIPRB

msg_type_not_comp_c 0x45 SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the SSP - SCP interface).

SGIPRB

ie_not_ex_or_imp_c 0x46 SGIPRB: Not in use at the moment (specified in the SSP - SCP interface).

SGIPRB



DN0516745Issue 11-1

invalid_ie_cont_c 0x47 SGIPRB: Not in use at the moment (specified in the SSP - SCP interface).

SGIPRB

ncompat_sm_trans_c 0x48 SGIPRB: Not in use at the moment (specified in the SSP - SCP interface).

SGIPRB

prot_error_unspec_c 0x49 SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the SSP - SCP interface).

GRNPRB: the VLR returned a location update reject with reject cause #111.

SGIPRB

GRNPRB

interwork_unspec_c 0x4A SGIPRB: SGIPRB can receive this cause code in the ReleaseSMS operation. SGIPRB can send this in the EventReportSMS operation (specified in the SSP - SCP interface).

SGIPRB

Ms_lost_c 0x4B GGBPRB: Radio contact is lost with the MS. GGBPRB

bad_quality_c 0x4C GGBPRB: Radio link quality is insufficient to continue communication.

GGBPRB

cell_reselection_c 0x4D GGBPRB: BSS has ordered the MS to perform a cell re-selection.

GGBPRB

No_rsp_c 0x4E GIPPRB (Case 1): The PDP context activation or modification was delayed in an inter-PAPU RAU because a PS Paging procedure was ongoing or a CS activity interrupted the RAU procedure. The PDP context setup is finished after these activities.

GIPPRB (Case 2): A streaming class PDP context was released because the PS Paging failed (MS is unreachable).

GIPPRB (Case 3): Iu-initiated PS Paging was unsuccessful in Gb-interface. This situation occurs

GIPPRB

Summary of changes

when there are both Gb and Iu cells in the same Routing Area.

GCSPRB: GCSPRB did not get the message it requested from GMGPRB.

GCSPRB

No_rsp_from_gsn_c 0x4F GMGPRB: GTPPRB informs GMGPRB that there was no response to the SGSN context request or identification request. The ongoing process is interrupted.

GTPPRB: GTPPRB informs GMGPRB that there was no response to the SGSN context request or identification request.

GMGPRB

GTPPRB

imei_chk_failed_c 0x51 GMGPRB: the MS is blacklisted and the IMEI check fails. Detach is performed.

GRNPRB: IMEI check of the subscriber failed because no EIR address was found.

GS1PRB: User authentication failed when IMEI or IMEI and Authentication check are requested.

GMGPRB

GRNPRB

GS1PRB

param_err_c 0x52 GRNPRB: erroneous IMSI is received from GMGPRB.

GMGPRB: in an attach, detach, or RAU update, the type is unknown. The attach or RAU is rejected.

GRNPRB

GMGPRB



DN0516745Issue 11-1

table_err_c 0x53 GIPPRB (Case 1): GIPPRB: an attach or inter-PAPU RAU is rejected during lower-layer GPRS mobility management procedures, because there is no capacity for new subscribers in the TLLI table. This is an internal error in the 2G SGSN that prevents an attach or inter PAPU RAU.

GIPPRB (Case 2): The Iu-initiated PS Paging could not be performed in the Gb-interface because the GIPPRB TLLI table was full.

GCSPRB: handling (reading or writing) of the GCSPRB file fails. The ongoing process is interrupted.

GMGPRB: handling (reading or writing) of GMGPRB files fails. The ongoing process is interrupted.

GIPPRB

GCSPRB

GMGPRB

protocol_c 0x54 GTPPRB: A protocol error has happened between the SGSN and the GGSN.

GMGPRB: unpacking the input message fails. Some parameters in the message were inappropriate. The ongoing process is interrupted.

GTPPRB

GMGPRB

ptmsi_alloc_fail_c 0x55 GMGPRB: PTMSI allocation fails and the old PTMSI cannot be used.

GMGPRB

opt_not_supp_c 0x57 GMGPRB: Authentication, IMEI check, PTMSI reallocation, or PTMSI signature reallocation is requested from GMGPRB, but the service is not activated in the SGSN.

GMGPRB

Summary of changes

No_rsp_from_scp_c 0x58 SGIPRB: no response from the SCP. The SCP did not answer before the expiry of the supervision timer (Tssf, TC_Guard). The cause code is sent to GMGPRB in the ssf_release_context_ind_s and ssf_release_gprs_ind_s messages.

SGIPRB

overload_c 0x59 GMGPRB: the procedure is discarded because of overload. The GMG does not get a ticket from tisero. The ongoing procedure is rejected.

GRNPRB: The procedure is discarded because of overload.

GMGPRB

GRNPRB

contr_roaming_rej_c 0x5A GMGPRB: Routing area update is restricted by Feature SG01004: Controlled Roaming. The subscriber is not allowed to roam.

GMGPRB

unknown_pdp_ctxt_c 0x5B GTPPRB: The requested PDP context was not found.

GTPPRB

unknown_dns_c 0x5C GTPPRB: The requested APN did not supply any IP addresses or the DNS did not answer.

GTPPRB

hand_ini_failed_c 0x5D GTPPRB: the hand process could not be created.

GCSPRB, GMGPRB: the hand process could not be created. The ongoing procedure is rejected.

GTPPRB

GCSPRB GMGPRB

No_rsp_from_ggsn_c 0x5F GTPPRB: The GGSN did not answer to an n3 amount of requests.

GTPPRB

unsucc_op_c 0x60 GTPPRB: GTPPRB master has removed the hand process forcefully.

GTPPRB

Op_not_allowed_c 0x61 GTPPRB: The same NSAPI already has a tunnel operation ongoing.

GTPPRB



DN0516745Issue 11-1

error_c 0x62 SGIPRB: SGIPRB switchover happens, the SGIPRB master has received a prepare_for_switchover_s message. This cause code is used only internally by SGIPRB between the SGIPRB-master and the SGIPRB-hand process. The switchover is indicated to the hand process with this cause code.

SGIPRB

discard_c 0x64 GTPPRB: an invalid packet is received and discarded.

GTPPRB

nsapi_in_use_c 0x66 GMGPRB: Subscriber tries to activate a PDP context that is already activated. PDP context activation is rejected.

GMGPRB

No_subscription_c 0x67 GMGPRB: The subscriber has no subscriptions in GSBASE. The PDP context activation procedure is rejected.

GMGPRB

No_pdp_context_c 0x68 SGIPRB: SGIPRB forwards this cause code to GMGPRB in the ssf_release_context_ind_s message when cause code is received from GTPRPB in the gtp_datavolume_res_s message. This is the case when there is no PDP context with the IMSI and NSAPI in question. The gtp_datavolume_res_s message is a response to the gtp_datavolume_req_s message sent by SGIPRB.

GMGPRB: modification or deactivation is attempted to a PDP context that does not exist. PDP context modification or deactivation is rejected.

SGIPRB

GMGPRB

invalid_ti_c 0x6A GSPPRB: The network has received an SM with an invalid transaction identifier.

GSPPRB

Summary of changes

No_sgsn_resources_c 0x6B GMGPRB: Adding PDP context to GCNFIL fails. The table is full or the maximum amount of contexts is exceeded. PDP context activation is rejected.

GMGPRB

pdp_type_changed_c 0x6D GMGPRB: PDP context type is changed in the HLR. An active PDP context is deactivated.

GMGPRB

apn_changed_c 0x6E GMGPRB: PDP context APN is changed in the HLR. An active PDP context is deactivated.

GMGPRB

No_linked_ti_c 0x70 GMGPRB: The MS tries to activate a secondary PDP context without a linked transaction identity. PDP context activation is rejected.

GMGPRB

max_pdp_exceeded_c 0x75 GMGPRB: The user has more PDP contexts than the supported amount of contexts in an inter SGSN RAU (RAU from other vendor's SGSN to Nokia SGSN). Not supported PDP contexts are deactivated.

GMGPRB

No_rsp_from_map_c 0x78 GRNPRB: The MAP protocol did not respond before the response timer expiry.

GRNPRB

abort_from_map_c

0x79 GRNPRB: An Abort message has been received from the MAP protocol.

The possible reasons are the following:

The destination network element (HLR, AuC, or EIR) did not respond to the MAP message sent by the SGSN.

Global Title (GT) analysis has not been created for the destination network element.

The destination network element aborted the MAP message sent by the SGSN.

GRNPRB

No_rsp_from_vlr_c 0x7A GRNPRB: The VLR did not respond before the response timer expiry.

GRNPRB

Db_error_c 0x7B GRNPRB: Database error in GSBASE. GRNPRB



DN0516745Issue 11-1

subscr_chk_fail_c 0x7C GRNPRB: Subscription check indicated that access to the network is not allowed.

GRNPRB

roaming_not_allowed_c 0x7E GRNPRB: the MAP protocol returned MAP error 'roaming not allowed'. Roaming is not allowed for the subscriber.

GMGPRB (Case 1): the MAP protocol returned MAP error roaming not allowed. For example, the HLR returns this cause when the services supported by the subscriber's home PLMN are not supported in the current PLMN. The attach or RAU is rejected.

GMGPRB (Case 2): roaming is not allowed for the subscriber (there is no roaming agreement with the subscriber's PLMN). The attach or RAU is rejected.

GMGPRB (Case 3): the MS does not support ciphering. The attach or RAU is rejected.

GMGPRB (Case 4): routing area update is rejected by Feature SG01004: Controlled Roaming. The subscriber is not allowed to roam.

GRNPRB

GMGPRB

hand_creation_fail_c 0x80 GRNPRB: Creation of hand process failed. GRNPRB

Vlr_unreachable_c 0x81 GRNPRB: The subscriber's VLR is unreachable or the VLR association does not exist.

GRNPRB

Db_no_subs_c 0x82 GRNPRB: Subscriber is not found from GSBASE. GRNPRB

Db_no_hlr_c 0x83 GRNPRB: The subscriber's HLR does not exist in GSBASE.

GRNPRB

Summary of changes

no_peer_response_c 0x85 GIPPRB (Case 1): the PDP context is released because the N200 retransmission counter has been exceeded during an ABM (re-)establishment procedure.

GIPPRB (Case 2): the MS is unable to respond to the SGSN-initiated XID reset. The cause code is set after the N200 counter has been exceeded.

GIPPRB (Case 3): the MS is unable to respond to the SGSN-initiated XID reset due to a CS activity.

GIPPRB

inv_xid_response_c 0x87 GIPPRB: The PDP context was released because the MS sent a XID response after a RAU procedure that was not encoded according to 3GPP TS 44.064 and 3GPP TS 44.065 specifications.

GIPPRB

Dm_received_c 0x88 GIPPRB: The PDP context was released because the MS sent a Disconnected Mode (DM) response while the SGSN established an acknowledged LLC data transfer mode.

GIPPRB

qos_mismatch_c 0x8B GIPPRB (Case 1): PDP context establishment or modification was rejected because the GPRS mobility management sent an unsupported value in the QoS reliability class attribute. This is an internal error in the 2G SGSN that prevented the establishment of a PDP context.

GIPPRB (Case 2): PDP context establishment or modification was rejected because the GPRS mobility management tried to allocate a new QoS profile to an existing SAPI. This is an internal error in the 2G SGSN that prevented the establishment of a PDP context.

GIPPRB

Gb_unavailable_c 0x8D GGBPRB: Internal error in the Gb interface. GGBPRB



DN0516745Issue 11-1

coll_attach_c 0x8E GSPPRB: the GSPPRB's GMM/SM hand uses this internal cause to inform the GSPPRB's GSMS hand to abort the SMS procedure. The SMS procedure collides with an attach procedure.

GMGPRB: colliding attach request from the MS. The network has an ongoing task and an attach request arrives from the MS. The ongoing procedure is interrupted or rejected and the attach procedure is started.

GSPPRB

GMGPRB

coll_ra_upd_c 0x8F GMGPRB: Colliding routing area update request from MS. The network has an ongoing task and a routing area update request arrives from the MS. The ongoing procedure is interrupted or rejected and the routing area update procedure is started.

Scenarios for collision of two RAUs from the same MS:

1. two incoming RAUs (the first one is killed with cause 0x8F)

2. one outgoing and one incoming RAU

GMGPRB

coll_detach_c 0x90 GSPPRB: the GSPPRB's GMM/SM hand uses this internal cause to inform the GSPPRB's GSMS hand to abort the SMS procedure. The SMS procedure collides with the detach procedure.

GMGPRB: The network has an MM or SM process ongoing and a detach request arrives from the MS or the network. The colliding detach interrupts the ongoing process and the detach is performed.

GSPPRB

GMGPRB

Summary of changes

coll_gmm_proc_c 0x91 GSPPRB: When an MO SMS or an MT SMS is received and there is already an ongoing GMM-procedure. The GSPPRB's GMM/SM hand uses this internal cause to inform the GSPPRB's GSMS hand to abort the SMS procedure. The SMS procedure collides with an attach or detach procedure.

GSPPRB

illegal_ms_c 0x93 GRNPRB: The VLR returned a location update reject with reject cause #3.

GRNPRB

mnr_c 0x94 GSPPRB: The maximum number of re-sends has been reached to the MS and the MS does not respond. Re-sends of different messages are defined in specification 3GPP TS 24.008.

GSPPRB

Cs_call_c 0x95 GMGPRB: the network has an ongoing MM or SM process and a CS call indication is received from the MS or the network. The ongoing process is interrupted and the CS call is activated.

GS1PRB: SMS delivery is interrupted because of active CS call.

GMGPRB

GS1PRB

gsp_exp_c 0x96 GMGPRB: the timer has expired while waiting for answer from GSPPRB or the MS to authentication and ciphering request during an MM or SM process. The ongoing process is interrupted.

GMGPRB

gip_err_c 0x97 GSPPRB: GIPPRB does not answer to radio parameter update or assign Kc. This is a fault in the SGSN.

GIPPRB: An MPE (memory protection error) has occurred in a GIPPRB hand process and the GIPPRB master informs GMM about the situation.

GSPPRB

GIPPRB



DN0516745Issue 11-1

gsp_err_c 0x98 GSPPRB: The GMM/SM hand uses this internal cause to inform the GSPPRB's GSMS hand to abort the SMS procedure when the GSPPRB's procedure timer has expired.

GSPPRB

coll_identity_enq_c 0x99 GSPPRB: This cause is set when the MS has an ongoing task and the network starts an identity enquiry procedure. This cause does not cause any failure and GSPPRB uses it to suspend the SMS procedure until the identity procedure is handled.

GSPPRB

coll_auth_c 0x9A GSPPRB: This cause is set when the MS has an ongoing task and the network starts an authentication procedure. This cause does not cause any failure and GSPPRB uses it to suspend the SMS procedure until the authentication procedure is handled.

GSPPRB

coll_ptmsi_realloc_c 0x9B GSPPRB: This cause is set when the MS has an ongoing task and the network starts a PTMSI reallocation procedure. This cause does not cause any failure and GSPPRB uses it to suspend the SMS procedure until the a PTMSI reallocation procedure is handled.

GSPPRB

nw_err_c 0x9C GSPPRB: This cause is set when the MS is not allowed to start any more procedures. The GSPPRB's GMM/SM hand uses this internal cause to inform the GSPPRB's GSMS hand to abort the SMS procedure.

GSPPRB

Summary of changes

cap_unspecified_c 0x9D SGIPRB: Unspecified error situations in SGIPRB. For example, a create session, a create context, a create CAP, an ActivityTest operation has failed, an unknown operation was received from the SCP, or the operation response is 'nack'. The cause code is sent to GMGPRB in the ssf_release_context_ind_s and ssf_release_gprs_ind_s messages.

SGIPRB

forced_deact_c 0x9F GCSPRB: GCSPRB asks GCHPRB to close all S-CDR of a certain IMSI. When GCSPRB does not receive S-CDR-related information from GMGPRB during PDP context deactivation or detach, all S-CDRs of the given IMSI are closed.

GCSPRB

illegal_me_c 0x0A1 GRNPRB: The VLR returned a location update reject with reject cause #6.

GRNPRB

plmn_not_allow_c 0x0A2 GRNPRB: The VLR returned a location update reject with reject cause #11.

GRNPRB

Loc_area_not_allow_c 0x0A3 GRNPRB: The VLR returned a location update reject with reject cause #12.

GRNPRB

roam_nt_allow_in_la_c 0x0A4 GRNPRB: The VLR returned a location update reject with reject cause #13.

GMGPRB: Routing area update is rejected by Feature SG01004: Controlled Roaming. The subscriber is not allowed to roam.

GRNPRB

GMGPRB

mandat_info_el_err_c 0x0A5 GRNPRB: The VLR returned a location update reject with reject cause #96.

GRNPRB

info_el_no_ex_or_i_c 0x0A6 GRNPRB: The VLR returned a location update reject with reject cause #99.

GRNPRB

imsi_unknwn_in_vlr_c 0x0A7 GRNPRB: The VLR returned a location update reject with reject cause #4.

GRNPRB

network_failure_c 0x0A8 GRNPRB: The VLR returned a location update reject with reject cause #17.

GRNPRB



DN0516745Issue 11-1

semantic_inc_msg_c 0x0A9 GRNPRB: The VLR returned a location update reject with reject cause #95.

GRNPRB

msg_not_ex_or_impl_c 0x0AA GRNPRB: The VLR returned a location update reject with reject cause #97.

GRNPRB

Vlr_congestion_c 0x0AB GRNPRB: The VLR returned a location update reject with reject cause #22.

GRNPRB

req_allr_fulfilled_c 0x0AD GTPPRB: The CG has already performed the requested operation.

GTPPRB

incorrect_seqnums_c 0x0AE GTPPRB: The CG reports that the sequence number of the released or cancelled packet's IE is incorrect.

GTPPRB

req_not_fulfilled_c 0x0AF GTPPRB: The CG did not perform the requested operation.

GTPPRB

cdr_decoding_error_c 0x0B0 GTPPRB: The CG could not decode the CDR. GTPPRB

No_suit_cell_in_la_c 0x0B1 GRNPRB: The VLR returned a location update reject with reject cause #15.

GRNPRB

coll_deact_c 0x0B2 GMGPRB: The network has an SM process ongoing and a PDP deactivation request arrives from the MS or the network. The colliding deactivation interrupts the ongoing process and PDP deactivation is performed.

GMGPRB

coll_act_c 0x0B3 GMGPRB: There is already an ongoing PDP activation in the network and a new PDP activation request arrives from the MS. The ongoing process is interrupted and the new activation is performed.

GMGPRB

coll_mod_c 0x0B4 GMGPRB: The network has a PDP modification ongoing and a new PDP modification request arrives from the MS. The ongoing process is interrupted and the new modification is performed.

GMGPRB

Summary of changes

info_to_gs1_c 0x0B5 GIPPRB: GIPPRB informs GS1 about the MS activity as requested by GS1PRB.

GIPPRB

unk_pdp_add_or_type_c

0x0B6 GTPPRB: The GGSN does not support the PDP address or PDP type requested by the SGSN.

GTPPRB

contr_roam_rl97_rej_c 0x0B7 GMGPRB: Roaming is restricted by Feature SG01004: Controlled Roaming. This cause is used when the MS is older than 3GPP Release 99. The routing area update or attach is rejected.

GMGPRB

Ac_max_bw_fail_c 0xB8 GMGPRB: Admission control: the RT PDP contexts exceeded the bandwidth limit.

GMGPRB

Ac_max_user_fail_c 0xB9 GMGPRB: Admission control: the RT PDP contexts exceeded the user limit.

GMGPRB

Ac_max_act_user_fail_c

0xBA GMGPRB: Admission control: the active RT PDP contexts exceeded the user limit.

GMGPRB

ac_max_bw_fail_2_c 0xBB GMGPRB: Secondary admission control: the RT PDP contexts exceeded the bandwidth limit.

GMGPRB

Ac_max_act_user_f_2_c

0xBC GMGPRB: Secondary admission control: the active RT PDP contexts exceeded the user limit.

GMGPRB

Ac_modify_fail_c 0xBD GMGPRB: Admission control: the RT PDP contexts exceeded the bandwidth limit in the PDP context modify procedure.

GMGPRB

pfc_create_fail_c 0xBE GMGPRB: The BSS rejects the PFC creation procedure.

GMGPRB

No_rsp_from_bss_c 0xBF GMGPRB: No response from BSS. GMGPRB

rt_setup_timeout_c 0xC0 GIPPRB: Streaming class PDP context was released when the context admission control timer expired. In this case, the setup of the streaming class PDP context was delayed too much.

GIPPRB

mo_sms_a_num_barr_c 0xC1 GS1PRB: MO-SMS denied based on A-number. GS1PRB

mo_sms_smsc_barr_c 0xC2 GS1PRB: MO-SMS denied based on SMSC. GS1PRB



DN0516745Issue 11-1

Mt_sms_smsc_barr_c 0xC3 GS1PRB: MT-SMS denied based on SMSC. GS1PRB

Llc_or_sndcp_fail_c 0xC4 GSPPRB: The MS sends a PDP context deactivation message with cause #25.

GSPPRB

insuf_recources_c 0xC5 GSPPRB: The MS sends a PDP context deactivation message with cause #26.

GSPPRB

regular_deact_c 0xC6 GSPPRB: The MS sends a PDP context deactivation message with cause #36.

GSPPRB

qos_not_accepted_c 0xC7 GSPPRB: The MS sends a PDP context deactivation with cause #37.

GSPPRB

No_pfc_support_c 0xC8 GGBPRB: The BSS does not support PFC procedures.

GGBPRB

alert_req_grn_case_c 0xC9 GIPPRB: GIPPRB informs GRNPRB about MS activity as requested by GRNPRB.

GIPPRB

inv_own_ip_address_c 0xCA GTPPRB: The GTP informs the GMG that its own PAPU IP address is invalid.

GTPPRB

not_prepaid_user_c 0xCB GTPPRB: Modification or deactivation was attempted to a PDP context that is not for prepaid or CAMEL subscriber.

GTPPRB

SGIPRB: SGIPRB forwards this cause code to GMGPRB in the ssf_release_context_ind_s message when cause code is received from GTPRPB in the gtp_datavolume_res_s message. This is the case when the GTP recognises that the subscriber is not a prepaid subscriber. The gtp_datavolume_res_s message is the response to the gtp_datavolume_req_s message sent by SGIPRB.

SGIPRB

Summary of changes

release_from_scp_c 0xCC SGIPRB: Release GPRS operation is received from the SCP. The SCP orders the SGSN to release the GPRS session and/or the PDP contexts. The cause code is sent to GMGPRB in the ssf_release_context_ind_s and ssf_release_gprs_ind_s messages.

SGIPRB

abort_from_cap_c 0xCD SGIPRB: TC_Abort is received from the SCP. The cause code is sent to GMGPRB in the ssf_release_context_ind_s and ssf_release_gprs_ind_s messages.

SGIPRB

disc_received_c 0xCE GIPPRB (Case 1): A PDP context was released because the MS sent a Disconnect (DISC) command when the SGSN established an acknowledged LLC data transfer mode.

GIPPRB (Case 2): A PDP context was released because the MS sent a Disconnect (DISC) command during the acknowledged LLC mode data transfer.

GIPPRB

out_of_memory_c 0xCF GIPPRB (Case 1): PDP context establishment or modification failed because there was no free memory left for the PDP context buffering mechanism.

GIPPRB (Case 2): PDP context was released because there was not enough memory for acknowledged LLC data transfer.

GIPPRB

inv_xid_command_c 0xD0 GIPPRB: A PDP context was released because the MS sent a XID command that was not encoded according to specifications 3GPP TS 44.064 and 3GPP TS 44.065.

GIPPRB



DN0516745Issue 11-1

no_resources_c 0xD1 GIPPRB (Case 1): The PDP context establishment was rejected because the maximum amount of supported PDP contexts had already been established. This is an internal error in the SGSN that prevents the establishment of a PDP context.

GIPPRB (Case 2): The Iu-initiated PS Paging could not be performed in the Gb-interface because there were no GIPPRB hand processes left.

GIPPRB (Case 3): The Iu-initiated PS Paging could not be performed in the Gb-interface because the GIPPRB hand creation failed.

GIPPRB (Case 4): The Iu-initiated PS Paging could not be performed in the Gb-interface because the provided TLLI was not in local format.

GIPPRB

nsapi_error_c 0xD2 GIPPRB (Case 1): The PDP context establishment was rejected because the GPRS mobility management sent an NSAPI value that had already been used by the SNDCP layer. This is an internal error in the 2G SGSN that prevented the establishment of a PDP context.

GIPPRB (Case 2): The PDP context modification or release was rejected by the SNDCP layer because the GPRS mobility management sent an NSAPI value that was unknown to SNDCP layer. This is an internal error in the 2G SGSN that caused the release of the PDP context.

GIPPRB

sndcp_out_of_sync_c 0xD4 GIPPRB: A PDP context was released because the SNDCP protocol entities in the 2G SGSN and the MS were not in synchrony.

GIPPRB

Summary of changes

variable_corrupted_c 0xD5 GIPPRB: The mapping of an SNDCP protocol layer internal parameter failed when a PDP context was being established. This is an internal error in the 2G SGSN that prevented the establishment of a PDP context.

GIPPRB

ptmsi_imsi_mismatch_c 0xD6 GMGPRB: There are two subscribers who have different IMSIs but have the same PTMSI.

GIPPRB: An Iu-initiated PS Paging was unsuccessful because neither IMSI nor P-TMSI matched with the one already known in the GIPPRB hand process.

GMGPRB

GIPPRB

max_subs_exceeded_c 0xD7 GMGPRB: The subscriber table in GMGPRB is full; there are no free records.

GMGPRB

ggsn_restarted_c 0xD8 GTPPRB: GTPPRB sets this error cause when the GGSN has restarted.

GTPPRB

sg_err_t_imei_fail_cs _allow_c

0xDB GMGPRB: When the feature enabling blacklisted MEs to have CS service (Feature SG02156) is active, emergency calls are possible for MEs with a blacklisted IMEI.

GMGPRB

ac_max_ave_bw_limit_c

0xDE GMGPRB: Admission control: the RT PDP contexts exceeded the average bandwidth limit.

GMGPRB

req_trf_c_not_avl_c 0xDF GMGPRB: This cause comes from the RNC (see

3GPP TS 25.413).

GSPPRB: The RNC sends for example a RAB assignment response with RANAP cause 18 (see 3GPP TS 25.413).

GMGPRB

GSPPRB

req_mbr_not_avail_c 0xE0 GMGPRB internal cause code


GMGPRB

GSPPRB



DN0516745Issue 11-1

req_mbr_dl_not_avail_c 0xE1 GMGPRB: GMGPRB internal cause code


GMGPRB

GSPPRB

req_mbr_ul_not_avail_c 0xE2 GMGPRB: internal cause code


GMGPRB

GSPPRB

req_gbr_not_avail_c 0xE3 GMGPRB: internal cause code


GMGPRB

GSPPRB

req_gbr_dl_not_avail_c 0xE4 GMGPRB: internal cause code


GMGPRB

GSPPRB

req_gbr_ul_not_avail_c 0xE5 GMGPRB: internal cause code


GMGPRB

GSPPRB

Summary of changes

req_tr_delay_not_a_c 0xE6 GMGPRB: internal cause code


GMGPRB

GSPPRB

invalid_rab_id_c 0xE7 GMGPRB: internal cause code


GMGPRB

GSPPRB

inv_rab_param_c_c 0xE8 GMGPRB: internal cause code


GMGPRB

GSPPRB

inv_rab_param_v_c 0xE9 GMGPRB: internal cause code


GMGPRB

GSPPRB

r_conn_lost_ue_c 0xEA GMGPRB: internal cause code


GMGPRB

GSPPRB



DN0516745Issue 11-1

Rls_due_ue_sig_c 0xEB GMGPRB: internal cause code


GMGPRB

GSPPRB

Rls_due_utran_r_c 0xEC GMGPRB: internal cause code


GMGPRB

GSPPRB

user_inactivity_c 0xED GMGPRB: internal cause code

GSPPRB: The RNC sends for example an Iu release request with RANAP cause 16 (see 3GPP TS 25.413).

GMGPRB

GSPPRB

no_res_tar_cell_c 0xEE GMGPRB: internal cause code


GMGPRB

GSPPRB

coll_og_attach_c 0xEF GMGPRB: An outgoing attach request collided with an ongoing procedure. The ongoing process is interrupted and the outgoing attach is performed.

GMGPRB

coll_og_rau_c 0xF0 GMGPRB: An outgoing RA update request collided with an ongoing procedure. The ongoing process is interrupted and the outgoing RA update is performed.

GMGPRB

Summary of changes

coll_purge_c 0xF1 GMGPRB: A purge request collided with an ongoing procedure. The ongoing process is interrupted and the purge is performed.

GMGPRB

coll_og_cs_call_c 0xF2 GMGPRB: An outgoing CS call indication collided in the previous location (in case of an SGSN Context Request where the extension header includes a Suspend Request). The ongoing process is interrupted and the outgoing CS call is performed.

GMGPRB

No_rsp_from_rnc_c 0xF3 GSPPRB: There is no response from the RNC to security mode-, RAB assignment-, or SRSN context request.

GSPPRB

rab_pre_empted_c 0xF4 GSPPRB: The RNC sends for example RAB assignment response with RANAP cause 53 (see 3GPP TS 25.413).

GSPPRB

trelocovera_exp_c 0xF5 GSPPRB: The SRNC sends for example Relocation cancel with RANAP cause 2 (see 3GPP TS 25.413).

GSPPRB

trelocprep_exp_c 0xF6 GSPPRB: The SRNC sends for example Relocation cancel with RANAP cause 3 (see 3GPP TS 25.413).

GSPPRB

treloccompl_exp_c 0xF7 GMGPRB: In relocation, while waiting for Relocation Complete, timer has been expired. Relocation is interrupted.

GMGPRB

tqueing_expiry_c 0xF8 GSPPRB: The RNC sends for example a RAB assignment response with RANAP cause 5 (see 3GPP TS 25.413).

Note

Queuing is not supported in the SGSN

GSPPRB

reloc_triggered_c 0xF9 GSPPRB: The RNC indicates failed operation because of relocation by sending RANAP cause 6 (see 3GPP TS 25.413).

GSPPRB



DN0516745Issue 11-1

trelocalloc_exp_c 0xFA GMGPRB: In relocation, while waiting for a response to Relocation Request, timer has been expired. Relocation is interrupted.

GSPPRB: CN indicates a failed Relocation resource allocation procedure due to the expiry of the timer TRELOCalloc.

GMGPRB

GSPPRB

unabl_estab_d_r_c 0xFB GSPPRB: The RNC sends for example a RAB assignment response with RANAP cause 8 (see 3GPP TS 25.413).

GSPPRB

unkn_target_rnc_c 0xFC GSPPRB: The CN rejects relocation with RANAP cause 9 (see 3GPP TS 25.413) because the target RNC is not known to the CN.

GSPPRB

reloc_cancelled_c 0xFD GMGPRB: Relocation cancel has been received. GMGPRB

successfu_reloc_c 0xFE GSPPRB: The RNC sends for example an Iu release request with RANAP cause 11 (see 3GPP TS 25.413).

GSPPRB

req_cip_a_n_sup_c 0xFF GSPPRB: The RNC rejects security mode procedure with RANAP cause 12 (see 3GPP TS 25.413) because of the requested ciphering parameters.

GSPPRB

Ch_ci_pro_n_sup_c 0x101 GSPPRB: The RNC rejects security mode procedure with RANAP cause 13 (see 3GPP TS 25.413) because there is a conflict with the existing security parameters.

GSPPRB

fail_r_if_proce_c 0x102 GSPPRB: The RNC sends for example an Iu release request with RANAP cause 14 (see 3GPP TS 25.413).

GSPPRB

time_criti_relo_c 0x103 GSPPRB: SRNC requests Relocation for time critical reason with RANAP cause 17 (see 3GPP TS 25.413).

GSPPRB

Summary of changes

req_tr_dela_n_a_c 0x104 GSPPRB: The RNC sends for example a RAB assignment response with RANAP cause 22 (see 3GPP TS 25.413).

GSPPRB

cond_viol_sdu_p_c 0x105 GSPPRB: The RNC sends for example a RAB assignment response with RANAP cause 24 (see 3GPP TS 25.413).

GSPPRB

cond_viol_t_h_p_c 0x106 GSPPRB: The RNC sends for example a RAB assignment response with RANAP cause 25 (see 3GPP TS 25.413).

GSPPRB

cond_viol_gbr_c 0x107 GSPPRB: The RNC sends for example a RAB assignment response with RANAP cause 26 (see 3GPP TS 25.413).

GSPPRB

Up_versio_n_sup_c 0x108 GSPPRB: The RNC sends for example a RAB assignment response with RANAP cause 27 (see 3GPP TS 25.413).

GSPPRB

iu_up_failure_c 0x109 GSPPRB: The RNC sends for example an Iu release request with RANAP cause 28 (see 3GPP TS 25.413).

GSPPRB

Rel_fail_targ_c 0x10A GSPPRB: The TRNC indicates a failed Relocation resource allocation with RANAP cause 29 (see 3GPP TS 25.413).

GSPPRB

no_remain_rab_c 0x10B GSPPRB: The RNC sends for example an Iu release request with RANAP cause 31 (see 3GPP TS 25.413).

GSPPRB

integ_othr_proc_c 0x10C GSPPRB: SRNC sends for example a Relocation cancel with RANAP cause 32 (see 3GPP TS 25.413).

GSPPRB

rep_integ_chk_f_c 0x10D GSPPRB: The RNC rejects security mode procedure with RANAP cause 37 (see 3GPP TS 25.413).

GSPPRB



DN0516745Issue 11-1

req_superseded_c 0x10F GSPPRB: The RNC sends for example a RAB assignment response with RANAP cause 39 (see 3GPP TS 25.413).

GSPPRB

res_opt_reloc_c 0x110 GSPPRB: SRNC requests Relocation for resource optimization with RANAP cause 41 (see 3GPP TS 25.413).

GSPPRB

req_info_na_c 0x111 GSPPRB: The RNC rejects request with RANAP cause 42 (see 3GPP TS 25.413).

GSPPRB

reloc_dsrbl_r_r_c 0x112 GSPPRB: SRNC requests Relocation for radio interface reasons with RANAP cause 43 (see 3GPP TS 25.413).

GSPPRB

reloc_n_su_targ_c 0x113 GMGPRB: Relocation Required message is not received with target RNC information.

GSPPRB: TRNC indicates failed Relocation resource allocation with RANAP cause 44 (see 3GPP TS 25.413).

GMGPRB

GSPPRB

directed_retry_c 0x114 GSPPRB: RANAP cause 45 (see 3GPP TS 25.413).

GSPPRB

rnc_un_est_rfcs_c 0x115 GSPPRB: The RNC sends for example a RAB assignment response with RANAP cause 47 (see 3GPP TS 25.413).

GSPPRB

dec_keys_n_avl_c 0x116 GSPPRB: The RNC rejects security mode procedure with RANAP cause 48 (see 3GPP TS 25.413).

GSPPRB

ded_ass_dat_n_a_c 0x117 GSPPRB: The RNC indicates failed procedure with RANAP cause 49 (see 3GPP TS 25.413).

GSPPRB

Summary of changes

reloc_targ_n_al_c 0x118 GSPPRB (Case 1): The RNC state is not 'available'.

GSPPRB (Case 2): LAI has not been configured to target RNC.

GSPPRB (Case 3): The allocation of connection ID failed.

GSPPRB

loc_report_cong_c 0x119 GSPPRB: The RNC indicates the failed location reporting procedure with RANAP cause 51 (see 3GPP TS 25.413).

GSPPRB

r_loa_serv_cell_c 0x11A RNC overload indication with RANAP cause 52 (see 3GPP TS 25.413).

----

geran_iu_fail_c 0x11B GSPPRB: The RNC sends for example a RAB assignment response with RANAP cause 54 (see 3GPP TS 25.413).

GSPPRB

a_r_due_sh_net_c 0x11C GSPPRB: The RNC indicates failed procedure with RANAP cause 55 (see 3GPP TS 25.413).

GSPPRB

rl_n_s_due_pue_c 0x11D GSPPRB: The TRNC indicates failed Relocation resource allocation with RANAP cause 56 (see 3GPP TS 25.413).

GSPPRB

loa_hig_in_tar_c 0x11E GSPPRB: The RNC indicates failed procedure with RANAP cause 57 (see 3GPP TS 25.413).

GSPPRB

unkn_iu_trns_as_c 0x11F GSPPRB: The RNC indicates failed procedure with RANAP cause 65 (see 3GPP TS 25.413).

GSPPRB

usr_restr_s_ind_c 0x120 GSPPRB: The RNC indicates location reporting procedure with RANAP cause 81 (see 3GPP TS 25.413).

GSPPRB

usr_restr_e_ind_c 0x121 GSPPRB: The RNC indicates location reporting procedure with RANAP cause 82 (see 3GPP TS 25.413).

GSPPRB

normal_release_c 0x122 GSPPRB: The RNC or CN indicates Iu release with RANAP cause 83 (see 3GPP TS 25.413).

GSPPRB



DN0516745Issue 11-1

trnsfr_syntax_e_c 0x123 GSPPRB: The RNC or CN indicates protocol error with RANAP cause 97 (see 3GPP TS 25.413).

GSPPRB

abstr_stx_e_r_c 0x124 GSPPRB: The RNC or CN indicates protocol error with RANAP cause 100 (see 3GPP TS 25.413).

GSPPRB

abstr_stx_e_i_c 0x125 GSPPRB: The RNC or CN indicates protocol error with RANAP cause 101 (see 3GPP TS 25.413).

GSPPRB

absrt_stx_e_f_c_c 0x126 GSPPRB: The RNC or CN indicates protocol error with RANAP cause 102 (see 3GPP TS 25.413).

GSPPRB

om_intervention_c 0x127 GSPPRB: The RNC indicates failed procedure with RANAP cause 113 (see 3GPP TS 25.413).

GSPPRB

no_resource_avl_c 0x128 GSPPRB: The RNC indicates failed procedure with RANAP cause 114 (see 3GPP TS 25.413).

GSPPRB

unspecific_fail_c 0x129 GMGPRB: A RAB Assignment Response is received with an unknown context identifier.

GSPPRB: The RNC indicates failed procedure with RANAP cause 115 (see 3GPP TS 25.413).

GMGPRB

GSPPRB

network_optimis_c 0x12A GSPPRB: The RNC indicates failed procedure with RANAP cause 116 (see 3GPP TS 25.413).

GSPPRB

max_sgsn_pdp_re_c 0x132 GCSPRB: The GCSPRB rejects request to activate a PDP context due to the lack of SGSN level capacity.

GCSPRB

iu_conn_fail_es_c 0x134 GSPPRB: The RNC or CN indicates the failed procedure with RANAP cause 66 (see 3GPP TS 25.413).

GSPPRB

hlr_acc_rest_2g_11_c 0x135 GMGPRB: Subscriber access to GERAN is rejected due to HLR access restriction, external cause #11 is sent to the MS.

GMGPRB

Summary of changes

hlr_acc_rest_2g_12_c 0x136 GMGPRB, GRNPRB: Subscriber access to GERAN is rejected due to HLR access restriction, external cause #12 is sent to the MS.

GMGPRB, GRNPRB


GMGPRB


GMGPRB


GMGPRB

hlr_acc_rest_3g_11_c 0x13A GMGPRB: Subscriber access to UTRAN is rejected due to HLR access restriction, external cause #11 is sent to the MS.

GMGPRB

hlr_acc_rest_3g_12_c 0x13B GMGPRB, GRNPRB: Subscriber access to UTRAN is rejected due to HLR access restriction, external cause #12 is sent to the MS.

GMGPRB, GRNPRB

hlr_acc_rest_3g_13_c 0x13C GMGPRB: Subscriber access to UTRAN is rejected due to HLR access restriction, external cause #13 is sent to the MS.

GMGPRB

hlr_acc_rest_3g_14_c 0x13D GMGPRB: Subscriber access to UTRAN is rejected due to HLR access restriction, external cause #14 is sent to the MS.

GMGPRB

hlr_acc_rest_3g_15_c 0x13E GMGPRB: Subscriber access to UTRAN is rejected due to HLR access restriction, external cause #15 is sent to the MS.

GMGPRB

plmn_rest_2gto2g_11_c 0x13F GMGPRB: GSM subscriber access to GERAN is rejected due to the local access restriction, external cause #11 is sent to the MS.

GMGPRB



DN0516745Issue 11-1

plmn_rest_2gto2g_12_c 0x140 GMGPRB: GSM subscriber access to GERAN is rejected due to the local access restriction, external cause #12 is sent to the MS.

GMGPRB


GMGPRB


GMGPRB


GMGPRB

plmn_rest_2gto3g_11_c 0x144 GMGPRB: GSM subscriber access to UTRAN is rejected due to the local access restriction, external cause #11 is sent to the MS.

GMGPRB


GMGPRB


GMGPRB


GMGPRB


GMGPRB

plmn_rest_3gto2g_11_c 0x149 GMGPRB: UMTS subscriber access to GERAN is rejected due to the local access restriction, external cause #11 is sent to the MS.

GMGPRB

Summary of changes

plmn_rest_3gto2g_12_c 0x14A GMGPRB: UMTS subscriber access to GERAN is rejected due to the local access restriction, external cause #12 is sent to the MS.

GMGPRB

plmn_rest_3gto2g_13_c 0x14B GMGPRB: UMTS subscriber access to GERAN is rejected due to local access restriction, external cause #13 is sent to the MS.

GMGPRB

plmn_rest_3gto2g_14_c 0x14C GMGPRB: UMTS subscriber access to GERAN is rejected due to the local access restriction, external cause #14 is sent to the MS.

GMGPRB

plmn_rest_3gto2g_15_c 0x14D GMGPRB: UMTS subscriber access to GERAN is rejected due to the local access restriction, external cause #15 is sent to the MS.

GMGPRB

plmn_rest_3gto3g_11_c 0x14E GMGPRB: UMTS subscriber access to UTRAN is rejected due to the local access restriction, external cause #11 is sent to the MS.

GMGPRB

plmn_rest_3gto3g_12_c 0x14F GMGPRB: UMTS subscriber access to UTRAN is rejected due to the local access restriction, external cause #12 is sent to the MS.

GMGPRB

plmn_rest_3gto3g_13_c 0x150 GMGPRB: UMTS subscriber access to UTRAN is rejected due to the local access restriction, external cause #13 is sent to the MS.

GMGPRB


GMGPRB


GMGPRB

subs_cnt_rest_2g_11_c 0x153 GMGPRB: The subscriber access to GERAN is rejected due to subscriber count access restriction, external cause #11 is sent to the MS.

GMGPRB



DN0516745Issue 11-1

subs_cnt_rest_2g_12_c 0x154 GCSPRB: The subscriber access to GERAN is rejected due to subscriber count access restriction, external cause #12 is sent to the MS.

GCSPRB


GMGPRB


GMGPRB


GMGPRB

subs_cnt_rest_3g_11_c 0x158 GMGPRB: The subscriber access to UTRAN is rejected due to subscriber count access restriction, external cause #11 is sent to the MS.

GMGPRB

subs_cnt_rest_3g_12_c 0x159 GCSPRB: The subscriber access to UTRAN is rejected due to subscriber count access restriction, external cause #12 is sent to the MS.

GCSPRB

subs_cnt_rest_3g_13_c 0x15A GMGPRB: The subscriber access to UTRAN is rejected due to subscriber count access restriction, external cause #13 is sent to the MS.

GMGPRB

subs_cnt_rest_3g_14_c 0x15B GMGPRB: The subscriber access to UTRAN is rejected due to subscriber count access restriction, external cause #14 is sent to the MS.

GMGPRB

subs_cnt_rest_3g_15_c 0x15C GMGPRB: The subscriber access to UTRAN is rejected due to subscriber count access restriction, external cause #15 is sent to the MS.

GMGPRB

coll_relocation_c 0x15D GMGPRB: A Relocation collided with an ongoing procedure. The ongoing process is interrupted and the relocation is performed.

GMGPRB

Summary of changes

coll_og_relocation_c 0x15E GMGPRB: An outgoing Relocation collided with an ongoing procedure. The ongoing process is interrupted and the outgoing relocation is performed.

GMGPRB

coll_serv_request_c 0x15F GMGPRB: A Service request collided with an ongoing procedure. The ongoing process is interrupted and the service request is performed.

GMGPRB

coll_isho_c 0x160 GMGPRB: A new procedure from a different system collided with an ongoing procedure. The ongoing process is interrupted and the new is performed.

GMGPRB

auth_no_resp_c 0x161 GSPPRB: Indication of the failed procedure, because there is no response to the authentication and ciphering request.

GSPPRB

identity_no_resp_c 0x162 GSPPRB: Indication of the failed procedure, because there is no response to the identity request.

GSPPRB

rel_due_sgsn_c 0x165 GMGPRB (Case 1): In Relocation Required message the received target RNC identifies the confusing PAPU identifier (possible configuration error).

GMGPRB (Case 2): Internal error in GMGPRB. Ongoing procedure information is missed.

GMGPRB

no_rsp_co_process_c 0x167 GMGPRB: The timer has expired while waiting for answer from the co-process. The ongoing process is interrupted, except if it is a detach or a PDP context deactivation.

GMGPRB

coll_iu_reset_c 0x168 GMGPRB: An Iu-reset request collided with an ongoing procedure. The ongoing process is interrupted and the Iu reset is performed.

GMGPRB



DN0516745Issue 11-1

coll_iu_release_c 0x16D GMGPRB: An Iu-release procedure collided with an ongoing procedure The ongoing process is interrupted and the Iu release is performed.

GMGPRB

rnc_unsup_rab_mod_c 0x16E GMGPRB: RNC initiated RAB modification although RNC doesn't support RAB modification

GMGPRB

dns_failure_c 0x170 GMGPRB: Inter SGSN RAU is received with cause code unknown_dns_c. GMGPRB changes this cause code to dns_failure_c. Optional feature.

GMGPRB

gtp_res_unavail_c 0x172 GSPPRB: RAB release procedure initiated by RNC when it has received GTP-Error indication.

GSPPRB

apn_access_denied_c 0x173 GTPPRB: Cause code (222) returned by the GGSN (see 3GPP TS 29.060). APN authentication fails - no subscription; the ongoing procedure is interrupted.

GTPPRB

pos_method_failure_c 0x177 GLRPRB, GSPPRB: Positioning failed or timer for location request expired.

GLRPRB, GSPPRB

subs_cnt_rest_cam_11_c

0x178 GMGPRB: The subscriber access is rejected due to camel subscriber count access restriction, external cause #11 is sent to the MS.

GMGPRB


0x179 GCSPRB: The subscriber access is rejected due to camel subscriber count access restriction, external cause #12 is sent to the MS.

GCSPRB


0x17A GMGPRB: The subscriber access is rejected due to camel subscriber count access restriction, external cause #13 is sent to the MS.

GMGPRB


0x17B GMGPRB: The subscriber access is rejected due to camel subscriber count access restriction, external cause #14 is sent to the MS.

GMGPRB

Summary of changes


0x17C GMGPRB: The subscriber access is rejected due to camel subscriber count access restriction, external cause #15 is sent to the MS.

GMGPRB

cs_ps_coordination_c 0x17D GMGPRB: SGSN may not able to provide service to the UE due MOCN feature SG01179.

GMGPRB

cap_unknown_apn_c 0x17E SGIPRB: Release GPRS operation is received from the SCP. Wrong APN settings in mobile. The SCP orders the SGSN to release the GPRS session and/or the PDP contexts. The cause code is sent to GMGPRB in the ssf_release_c

Documents

SGSN SG7.0 CD6 Cause Description