IntroductionUse this document for quick installation and setup.

Teledyne LeCroy’s SFF-8639 to PCI Express 3.0 Adapter card provides a quick and simple means for test and debug of Solid State Drives (SSDs) based on PCI Express (PCIe®) protocols. It supports data rates of 2.5 GT/s (Gen1), 5 GT/s (Gen2) and 8 GT/s (Gen3). The Port B SFF-8639 Adapter looks exactly the same as the Port A adapter except for the bracket label which reads

"Dual Port SFF-8639 to PCIe Adapter Port B". Functionally, the Port B SFF-8639 Adapter works up to X2 since only Lanes 0 and 1 are routed in the PCB from the PCIe edge connector to the Port B of the SFF-8639 connector.

SFF-8639 Single-Port Adapter Card

SFF-8639 to PCI Express 3.0 AdapterQuick Start

1

ComponentsThe analyzer package includes the following components: • SFF-8639 single-port Adapter card• Power supply 12V @ 3A• Quick Start Guide (this document)Inspect the received shipping container for any damage. Unpack the container and account for each of the system components listed on the accompanying packing list. Visually inspect each component for absence of damage. In the event of damage, notify the shipper and Teledyne LeCroy. Retain all shipping materials for shipper’s inspection.

2

3 ConnectionsPerform to the following steps to connect the Adapter (see the image below):1. Insert the SSF-8639 device under test (DUT) through the 2.5" bracket mak-

ing sure it connects properly in the bottom SSF-8639 connector. 2. Make sure the power for the DUT is sourced correctly using switches SW2

and SW3. The factory default positions are SW1.1 OFF, SW1.2 ON, SW1.3 OFF, SW1.4 OFF, SW3 3.3V and SW2 12V HOST. See the tables below to source the correct power for the DUT.

3. Make sure only switch 2 from the DIP switch array SW1 is in the on position. The PRSNT# pins configuration is X1 or X4 device is selected using SW1 according to the table.

4. Plug the adapter with the device under test in any PCI Express slot.5. Connect the power supply to the external power jack (J3) if needed.

PCI Express (PCIe) Interface(plugs into PCI Express slot)

Device Under Test (DUT)

SW1 SW3 SW2

External power jack 12V

See section 4 for switch configurations.

Configuration

SW1

Note: Up to X2 for Port B Adapter

SW2

SW3

WARNING: When sourcing 5V from SW3 make sure external power cable is supplied through J3.

SW1.1 SW1.2 SW1.3 SW1.4 Boot Configuration

ON OFF X X X1

OFF ON X X X4 (see note below)

Others reserved

SW2 Position 12V Power to DUT

12V EXT From J3 12V

12V HOST From PCIe Bus 12V

SW3 Position Power to DUT source

3.3V From PCIe Bus 3.3V

5V From J3 regulated down to 5V

4

Copyright© 2013 Teledyne LeCroy, Inc. All rights reserved. Part Number: 923879-00 Rev BThis document may be printed and reproduced without additional permission, but all copies should contain this copyright notice.

Trademarks and ServicemarksTeledyne LeCroy is a trademark of Teledyne LeCroy. All other trademarks are property of their respective companies.

ChangesProduct specifications are subject to change without notice.Teledyne LeCroy reserves the right to revise the information in this document without notice or penalty.

Teledyne LeCroy Customer SupportOnline DownloadPeriodically check the Teledyne LeCroy Protocol Solutions Group web site for software updates and other support related to this product. Software updates are available to users with a current Maintenance Agreement. Mail: 3385 Scott Blvd., Santa Clara, CA 95054-3115Web: teledynelecroy.com/tm/Library/software/PSG E-mail: psgsupport@teledynelecroy.comTel: (800) 909-7112 (USA and Canada) Tel: (408) 653-1260 (worldwide)Fax: (408) 727-6622 (worldwide)

Environmental Conditions

• Temperature: Operating 32° F to 122° F (0° C to 50° C) • Temperature: Non-Operating 14° F to 176° F (-10° C to 80° C)• Humidity: Operating 10% to 90% RH (non-condensing)

5